| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When using the SCMP mode instead of SUBU, this RTC can also support
other input frequencies than 32768Hz. Also, upcoming SoCs will only
support SCMP.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250526095801.35781-8-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Datasheet says that the controller must be disabled before setting up
either SUBU or SCMP. This did not matter so far because the driver only
supported SUBU which was the default, too. It is good practice to follow
datasheet recommendations, though. It will also be needed because SCMP
mode will be added in a later patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250526095801.35781-7-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The external crystal can be a second clock input. It is needed for the
SCMP counting method which allows using crystals different than 32768Hz.
It is also needed for an upcoming SoC which only supports the SCMP
method.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250526095801.35781-6-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The driver currently uses dev_err for messages that have a very low probability
of being read by the user as the error will probably never happen and the
systems with the RTC probably don't have any user able to read the message.
Moreover, the only user action after getting this message is the restart the
action so drop the level to dev_dbg.
Link: https://lore.kernel.org/r/20250525222153.1472917-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The ocillator on the m41t62 (and other chips of this type) needs
a kickstart upon a failure; the RTC read routine will notice the
oscillator failure and fail reads. This is added in the RTC write
routine; this allows the system to know that the time in the RTC
is accurate. This is following the procedure described in section
3.11 of "https://www.st.com/resource/en/datasheet/m41t62.pdf"
Signed-off-by: A. Niyas Ahamed Mydeen <nmydeen@mvista.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Link: https://lore.kernel.org/r/20250402120546.336657-2-nmydeen@mvista.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add a RTC driver for NXP S32G2/S32G3 SoCs.
RTC tracks clock time during system suspend. It can be a wakeup source
for the S32G2/S32G3 SoC based boards.
The RTC module from S32G2/S32G3 is not battery-powered and it is not kept
alive during system reset.
Co-developed-by: Bogdan Hamciuc <bogdan.hamciuc@nxp.com>
Signed-off-by: Bogdan Hamciuc <bogdan.hamciuc@nxp.com>
Co-developed-by: Ghennadi Procopciuc <Ghennadi.Procopciuc@nxp.com>
Signed-off-by: Ghennadi Procopciuc <Ghennadi.Procopciuc@nxp.com>
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Enric Balletbo i Serra <eballetbo@kernel.org>
Link: https://lore.kernel.org/r/20250403103346.3064895-3-ciprianmarian.costea@oss.nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
RTC tracks clock time during system suspend and it is used as a wakeup
source on S32G2/S32G3 architecture.
RTC from S32G2/S32G3 is not battery-powered and it is not kept alive
during system reset.
Co-developed-by: Bogdan-Gabriel Roman <bogdan-gabriel.roman@nxp.com>
Signed-off-by: Bogdan-Gabriel Roman <bogdan-gabriel.roman@nxp.com>
Co-developed-by: Ghennadi Procopciuc <ghennadi.procopciuc@nxp.com>
Signed-off-by: Ghennadi Procopciuc <ghennadi.procopciuc@nxp.com>
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250403103346.3064895-2-ciprianmarian.costea@oss.nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add SAMA7D65 RTT compatible to DT bindings documentation.
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/183474a65377f4030360166a5f2659af7323e82b.1744666011.git.Ryan.Wanner@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add SAMA7D65 RTC compatible to DT bindings documentation.
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/a274485331628be0bcf382b1ba489d4555fa49c8.1744666011.git.Ryan.Wanner@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
When an application sets and enables an alarm on Loongson RTC devices,
the alarm notification fails to propagate to userspace because the
ACPI event handler omits calling rtc_update_irq().
As a result, processes waiting via select() or poll() on RTC device
files fail to receive alarm notifications.
The ACPI interrupt is also triggered multiple times. In loongson_rtc_handler,
we need to clear TOY_MATCH0_REG to resolve this issue.
Fixes: 09471d8f5b39 ("rtc: loongson: clear TOY_MATCH0_REG in loongson_rtc_isr()")
Fixes: 1b733a9ebc3d ("rtc: Add rtc driver for the Loongson family chips")
Signed-off-by: Liu Dalin <liudalin@kylinsec.com.cn>
Reviewed-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/20250509084416.7979-1-liudalin@kylinsec.com.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Implement the RTC driver for CV1800, which able to provide time alarm.
Signed-off-by: Jingbao Qiu <qiujingbao.dlmu@gmail.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20250507195626.502240-1-alexander.sverdlin@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The driver only support OF probe so drop the unused platform module
alias.
Fixes: 4e64350f42e2 ("rtc: add STM32 RTC driver")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250423130318.31244-8-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The driver only support OF probe so drop the unused platform module
alias.
Fixes: ae05c95074e0 ("rtc: s3c: add s3c_rtc_data structure to use variant data instead of s3c_cpu_type")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Fixes: 0d297df03890 ("ARM: s3c: simplify platform code")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250423130318.31244-7-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The driver only support OF probe so drop the unused platform module
alias.
Fixes: 5a418558cdae ("rtc: pm8xxx: add support for devicetree")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250423130318.31244-6-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The driver only support OF probe so drop the unused platform module
alias.
Fixes: 24e1f2c9383e ("rtc: ingenic: Only support probing from devicetree")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20250423130318.31244-5-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The driver only support OF probe so drop the unused platform module
alias.
Fixes: 80ca3277bc7f ("rtc: da9063: Add DA9062 RTC capability to DA9063 RTC driver")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250423130318.31244-4-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The driver only supports OF probe so drop the unused platform module
alias.
Fixes: dd3bf50b35e3 ("rtc: cpcap: new rtc driver")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250423130318.31244-3-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The driver only support OF probe so drop the unused platform module
alias.
Fixes: 288d9cf1764a ("rtc: at91rm9200: use of_device_get_match_data()")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250423130318.31244-2-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
On many Qualcomm platforms the PMIC RTC control and time registers are
read-only so that the RTC time can not be updated. Instead an offset
needs be stored in some machine-specific non-volatile memory, which a
driver can take into account.
On platforms where the offset is stored in a Qualcomm specific UEFI
variable the variables are also accessed in a non-standard way, which
means that the OS cannot assume that the variable service is available
by the time the driver probes.
Use the new 'qcom,uefi-rtc-info' property to determine whether to probe
defer until the UEFI offset becomes available so that the offset can be
used also when the RTC driver is built in or when a dependency of the
UEFI variable driver is built as a module (e.g. the driver for the SCM
interconnects).
Fixes: bba38b874886 ("rtc: pm8xxx: add support for uefi offset")
Reported-by: Rob Clark <robdclark@gmail.com>
Link: https://lore.kernel.org/lkml/CAF6AEGsfke=x0p1b2-uNX6DuQfRyEjVbJaxTbVLDT2YvSkGJbg@mail.gmail.com/
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250423075143.11157-3-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
On many Qualcomm platforms the PMIC RTC control and time registers are
read-only so that the RTC time can not be updated. Instead an offset
needs be stored in some machine-specific non-volatile memory, which a
driver can take into account.
On platforms where the offset is stored in a Qualcomm specific UEFI
variable the variables are also accessed in a non-standard way, which
means that the OS cannot assume that the variable service is available
by the time the RTC driver probes.
Add a 'qcom,uefi-rtc-info' boolean flag to indicate that the RTC offset
is stored in a Qualcomm specific UEFI variable so that the OS can
determine whether to wait for it to become available.
The UEFI variable is
882f8c2b-9646-435f-8de5-f208ff80c1bd-RTCInfo
and holds a 12-byte structure where the first four bytes is a GPS time
offset in little-endian byte order.
Link: https://lore.kernel.org/all/aAecIkgmTTlThKEZ@hovoldconsulting.com/
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250423075143.11157-2-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Enabling the compile test should not cause automatic enabling of all
drivers, but only allow to choose to compile them.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250417074640.81363-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
KMSAN complains that alarm->time can be used uninitialized. Pass 0 to
trace_rtc_read_alarm in case it has not been set.
Link: https://lore.kernel.org/r/20250408144203.3869821-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The code for enabling and disabling the irq is so similar that it can
easily be handled by one function. Like in most other RTC drivers. Save
the duplicated code and one layer of indirection.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250320102218.10781-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
It is good practice to clear running interrupts before removing the
driver. This is not really a bugfix because on current systems RuntimePM
will disable the module clock, so interrupts won't be initiated. The
dependency on that behaviour is subtle, though. Better be self-contained
and clean up when removing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250312100105.36767-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use the BIT macro, use curly braces for else-blocks, don't split strings
over multiple lines, annotate the lock, update copyright.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250227134256.9167-18-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
No need to store the resource for the registers in the per-device struct
because we only need it during probe. Remove some unneeded unlikely()
while here and correct the type of 'regsize'.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250227134256.9167-17-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The wrapper to enable interrupts is so thin that we can use it directly.
Also gets rid of an 'inline' which doesn't make sense here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250227134256.9167-16-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
We only need the alarm_irq handler. That means we can remove everything
related to periodic_irq and carry_irq. Also, the shared handler can go
since we only we need the alarm interrupt in any case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250227134256.9167-15-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Because periodic interrupts are emulated by the RTC core, the PIE
handling code can simply go away now. And with it the custom proc-file.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250227134256.9167-14-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
With old, custom UIE handling removed, we can now disable the carry
interrupt in probe() and leave it like this. No further handling is
required.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250227134256.9167-13-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Since commit e428c6a2772b ("RTC: Clean out UIE icotl implementations"),
the flag for UIE cannot be set anymore. Because UIE is now handled via
regular alarms and a timerqueue by the RTC core, the UIE handling code
can simply go away now.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250227134256.9167-12-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The DT bindings for this driver define the interrupts in the order as
they are numbered in the interrupt controller. The old platform_data,
however, listed them in a different order. So, for DT based platforms,
they are mixed up. Assign them specifically for DT, so we can keep the
bindings stable. After the fix, 'rtctest' passes again on the Renesas
Genmai board (RZ-A1 / R7S72100).
Fixes: dab5aec64bf5 ("rtc: sh: add support for rza series")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250227134256.9167-11-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
|
|
The "real" linux/types.h UAPI header gracefully degrades to a NOOP when
included from assembly code.
Mirror this behaviour in the tools/ variant.
Test for __ASSEMBLER__ over __ASSEMBLY__ as the former is provided by the
toolchain automatically.
Reported-by: Mark Brown <broonie@kernel.org>
Closes: https://lore.kernel.org/lkml/af553c62-ca2f-4956-932c-dd6e3a126f58@sirena.org.uk/
Fixes: c9fbaa879508 ("selftests: vDSO: parse_vdso: Use UAPI headers instead of libc headers")
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Link: https://patch.msgid.link/20250321-uapi-consistency-v1-1-439070118dc0@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
- support up to 8192 processors
- add cpuidle governor debug telemetry, disabled by default
- update default output to exclude cpuidle invocation counts
- bug fixes
* tag 'turbostat-2025.05.06' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: v2025.05.06
tools/power turbostat: disable "cpuidle" invocation counters, by default
tools/power turbostat: re-factor sysfs code
tools/power turbostat: Restore GFX sysfs fflush() call
tools/power turbostat: Document GNR UncMHz domain convention
tools/power turbostat: report CoreThr per measurement interval
tools/power turbostat: Increase CPU_SUBSET_MAXCPUS to 8192
tools/power turbostat: Add idle governor statistics reporting
tools/power turbostat: Fix names matching
tools/power turbostat: Allow Zero return value for some RAPL registers
tools/power turbostat: Clustered Uncore MHz counters should honor show/hide options
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire fix from Vinod Koul:
- add missing config symbol CONFIG_SND_HDA_EXT_CORE required for asoc
driver CONFIG_SND_SOF_SOF_HDA_SDW_BPT
* tag 'soundwire-6.15-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
ASoC: SOF: Intel: Let SND_SOF_SOF_HDA_SDW_BPT select SND_HDA_EXT_CORE
|
|
Support up to 8192 processors
Add cpuidle governor debug telemetry, disabled by default
Update default output to exclude cpuidle invocation counts
Bug fixes
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Create "pct_idle" counter group, the sofware notion of residency
so it can now be singled out, independent of other counter groups.
Create "cpuidle" group, the cpuidle invocation counts.
Disable "cpuidle", by default.
Create "swidle" = "cpuidle" + "pct_idle".
Undocument "sysfs", the old name for "swidle", but keep it working
for backwards compatibilty.
Create "hwidle", all the HW idle counters
Modify "idle", enabled by default
"idle" = "hwidle" + "pct_idle" (and now excludes "cpuidle")
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf event fix from Ingo Molnar:
"Fix a perf events time accounting bug"
* tag 'perf-urgent-2025-04-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix child_total_time_enabled accounting bug at task exit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
- Fix a nonsensical Kconfig combination
- Remove an unnecessary rseq-notification
* tag 'sched-urgent-2025-04-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq: Eliminate useless task_work on execve
sched/isolation: Make CONFIG_CPU_ISOLATION depend on CONFIG_SMP
|
|
... and don't error out so hard on missing module descriptions.
Before commit 6c6c1fc09de3 ("modpost: require a MODULE_DESCRIPTION()")
we used to warn about missing module descriptions, but only when
building with extra warnigns (ie 'W=1').
After that commit the warning became an unconditional hard error.
And it turns out not all modules have been converted despite the claims
to the contrary. As reported by Damian Tometzki, the slub KUnit test
didn't have a module description, and apparently nobody ever really
noticed.
The reason nobody noticed seems to be that the slub KUnit tests get
disabled by SLUB_TINY, which also ends up disabling a lot of other code,
both in tests and in slub itself. And so anybody doing full build tests
didn't actually see this failre.
So let's disable SLUB_TINY for build-only tests, since it clearly ends
up limiting build coverage. Also turn the missing module descriptions
error back into a warning, but let's keep it around for non-'W=1'
builds.
Reported-by: Damian Tometzki <damian@riscv-rocks.de>
Link: https://lore.kernel.org/all/01070196099fd059-e8463438-7b1b-4ec8-816d-173874be9966-000000@eu-central-1.amazonses.com/
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Fixes: 6c6c1fc09de3 ("modpost: require a MODULE_DESCRIPTION()")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Probe cpuidle "sysfs" residency and counts separately,
since soon we will make one disabled on, and the
other disabled off.
Clarify that some BIC (build-in-counters) are actually "groups".
since we're about to re-name some of those groups.
no functional change.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Do fflush() to discard the buffered data, before each read of the
graphics sysfs knobs.
Fixes: ba99a4fc8c24 ("tools/power turbostat: Remove unnecessary fflush() call")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Document that on Intel Granite Rapids Systems,
Uncore domains 0-2 are CPU domains, and
uncore domains 3-4 are IO domains.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The CoreThr column displays total thermal throttling events
since boot time.
Change it to report events during the measurement interval.
This is more useful for showing a user the current conditions.
Total events since boot time are still available to the user via
/sys/devices/system/cpu/cpu*/thermal_throttle/*
Document CoreThr on turbostat.8
Fixes: eae97e053fe30 ("turbostat: Support thermal throttle count print")
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: Chen Yu <yu.c.chen@intel.com>
|
|
On systems with >= 1024 cpus (in my case 1152), turbostat fails with the error output:
"turbostat: /sys/fs/cgroup/cpuset.cpus.effective: cpu str malformat 0-1151"
A similar error appears with the use of turbostat --cpu when the inputted cpu
range contains a cpu number >= 1024:
# turbostat -c 1100-1151
"--cpu 1100-1151" malformed
...
Both errors are caused by parse_cpu_str() reaching its limit of CPU_SUBSET_MAXCPUS.
It's a good idea to limit the maximum cpu number being parsed, but 1024 is too low.
For a small increase in compute and allocated memory, increasing CPU_SUBSET_MAXCPUS
brings support for parsing cpu numbers >= 1024.
Increase CPU_SUBSET_MAXCPUS to 8192, a common setting for CONFIG_NR_CPUS on x86_64.
Signed-off-by: Justin Ernst <justin.ernst@hpe.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer cleanups from Thomas Gleixner:
"A set of final cleanups for the timer subsystem:
- Convert all del_timer[_sync]() instances over to the new
timer_delete[_sync]() API and remove the legacy wrappers.
Conversion was done with coccinelle plus some manual fixups as
coccinelle chokes on scoped_guard().
- The final cleanup of the hrtimer_init() to hrtimer_setup()
conversion.
This has been delayed to the end of the merge window, so that all
patches which have been merged through other trees are in mainline
and all new users are catched.
Doing this right before rc1 ensures that new code which is merged post
rc1 is not introducing new instances of the original functionality"
* tag 'timers-cleanups-2025-04-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tracing/timers: Rename the hrtimer_init event to hrtimer_setup
hrtimers: Rename debug_init_on_stack() to debug_setup_on_stack()
hrtimers: Rename debug_init() to debug_setup()
hrtimers: Rename __hrtimer_init_sleeper() to __hrtimer_setup_sleeper()
hrtimers: Remove unnecessary NULL check in hrtimer_start_range_ns()
hrtimers: Make callback function pointer private
hrtimers: Merge __hrtimer_init() into __hrtimer_setup()
hrtimers: Switch to use __htimer_setup()
hrtimers: Delete hrtimer_init()
treewide: Convert new and leftover hrtimer_init() users
treewide: Switch/rename to timer_delete[_sync]()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more irq updates from Thomas Gleixner:
"A set of updates for the interrupt subsystem:
- A treewide cleanup for the irq_domain code, which makes the naming
consistent and gets rid of the original oddity of naming domains
'host'.
This is a trivial mechanical change and is done late to ensure that
all instances have been catched and new code merged post rc1 wont
reintroduce new instances.
- A trivial consistency fix in the migration code
The recent introduction of irq_force_complete_move() in the core
code, causes a problem for the nostalgia crowd who maintains ia64
out of tree.
The code assumes that hierarchical interrupt domains are enabled
and dereferences irq_data::parent_data unconditionally. That works
in mainline because both architectures which enable that code have
hierarchical domains enabled. Though it breaks the ia64 build,
which enables the functionality, but does not have hierarchical
domains.
While it's not really a problem for mainline today, this
unconditional dereference is inconsistent and trivially fixable by
using the existing helper function irqd_get_parent_data(), which
has the appropriate #ifdeffery in place"
* tag 'irq-urgent-2025-04-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/migration: Use irqd_get_parent_data() in irq_force_complete_move()
irqdomain: Stop using 'host' for domain
irqdomain: Rename irq_get_default_host() to irq_get_default_domain()
irqdomain: Rename irq_set_default_host() to irq_set_default_domain()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A revert to fix a adjtimex() regression:
The recent change to prevent that time goes backwards for the coarse
time getters due to immediate multiplier adjustments via adjtimex(),
changed the way how the timekeeping core treats that.
That change result in a regression on the adjtimex() side, which is
user space visible:
1) The forwarding of the base time moves the update out of the
original period and establishes a new one. That's changing the
behaviour of the [PF]LL control, which user space expects to be
applied periodically.
2) The clearing of the accumulated NTP error due to #1, changes the
behaviour as well.
An attempt to delay the multiplier/frequency update to the next tick
did not solve the problem as userspace expects that the multiplier or
frequency updates are in effect, when the syscall returns.
There is a different solution for the coarse time problem available,
so revert the offending commit to restore the existing adjtimex()
behaviour"
* tag 'timers-urgent-2025-04-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "timekeeping: Fix possible inconsistencies in _COARSE clockids"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"One important fix and one small configuration update.
The first patch by Artur Rojek fixes an issue with the J2 firmware
loader not being able to find the location of the device tree blob due
to insufficient alignment of the .bss section which rendered J2 boards
unbootable.
The second patch by Johan Korsnes updates the defconfigs on sh to drop
the CONFIG_NET_CLS_TCINDEX configuration option which became obsolete
after 8c710f75256b ("net/sched: Retire tcindex classifier").
Summary:
- sh: defconfig: Drop obsolete CONFIG_NET_CLS_TCINDEX
- sh: Align .bss section padding to 8-byte boundary"
* tag 'sh-for-v6.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: defconfig: Drop obsolete CONFIG_NET_CLS_TCINDEX
sh: Align .bss section padding to 8-byte boundary
|
