| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2017-11-21
This series contains fixes for igb/vf, ixgbe/vf, i40e/vf and fm10k.
Jake fixes a regression issue with older firmware, where we were using
the NVM lock to synchronize NVM reads for all devices and firmware
versions, yet this caused issues with older firmware prior to version
1.5. Fixed this by only grabbing the lock for newer devices and firmware
version 1.5 or newer.
Zijie Pan fixes the calculation of the i40e VF MAC addresses, where it was
possible to increment to the next MAC entry without calling
i40e_add_mac_filter().
Amritha removes the upper limit of 64 queues on a channel VSI since the
upper bound is determined by the VSI's num_queue_pairs.
Filip fixes an issue during FLR resets, where should have been checking
for upcoming core reset and if so, just return with I40E_ERR_NOT_READY.
Alan fixes the notifying clients of l2 parameters by copying the
parameters to the client instance struct and re-organizes the priority
in which the client tasks fire so that if the flag for notifying l2
params is set, it will trigger before the client open task. Also fixed
the promiscuous settings after reset for all the VSI's.
Brian King from IBM fixes an issue seen on Power systems which would
result in skb list corruption and eventual kernel oops. Brian
provides the same fix for nearly all our drivers, to replace the
read_barrier_depends with smp_rmb() to ensure loads are ordered with
respect to the load of tx_buffer->next_to_watch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY on BCM7278 has an additional bit that needs to be cleared:
IDDQ_GLOBAL_PWR, without doing this, the PHY remains stuck in reset out
of suspend/resume cycles.
Fixes: 0fe9933804eb ("net: dsa: bcm_sf2: Add support for BCM7278 integrated switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2017-11-23
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Several BPF offloading fixes, from Jakub. Among others:
- Limit offload to cls_bpf and XDP program types only.
- Move device validation into the driver and don't make
any assumptions about the device in the classifier due
to shared blocks semantics.
- Don't pass offloaded XDP program into the driver when
it should be run in native XDP instead. Offloaded ones
are not JITed for the host in such cases.
- Don't destroy device offload state when moved to
another namespace.
- Revert dumping offload info into user space for now,
since ifindex alone is not sufficient. This will be
redone properly for bpf-next tree.
2) Fix test_verifier to avoid using bpf_probe_write_user()
helper in test cases, since it's dumping a warning into
kernel log which may confuse users when only running tests.
Switch to use bpf_trace_printk() instead, from Yonghong.
3) Several fixes for correcting ARG_CONST_SIZE_OR_ZERO semantics
before it becomes uabi, from Gianluca. More specifically:
- Add a type ARG_PTR_TO_MEM_OR_NULL that is used only
by bpf_csum_diff(), where the argument is either a
valid pointer or NULL. The subsequent ARG_CONST_SIZE_OR_ZERO
then enforces a valid pointer in case of non-0 size
or a valid pointer or NULL in case of size 0. Given
that, the semantics for ARG_PTR_TO_MEM in combination
with ARG_CONST_SIZE_OR_ZERO are now such that in case
of size 0, the pointer must always be valid and cannot
be NULL. This fix in semantics allows for bpf_probe_read()
to drop the recently added size == 0 check in the helper
that would become part of uabi otherwise once released.
At the same time we can then fix bpf_probe_read_str() and
bpf_perf_event_output() to use ARG_CONST_SIZE_OR_ZERO
instead of ARG_CONST_SIZE in order to fix recently
reported issues by Arnaldo et al, where LLVM optimizes
two boundary checks into a single one for unknown
variables where the verifier looses track of the variable
bounds and thus rejects valid programs otherwise.
4) A fix for the verifier for the case when it detects
comparison of two constants where the branch is guaranteed
to not be taken at runtime. Verifier will rightfully prune
the exploration of such paths, but we still pass the program
to JITs, where they would complain about using reserved
fields, etc. Track such dead instructions and sanitize
them with mov r0,r0. Rejection is not possible since LLVM
may generate them for valid C code and doesn't do as much
data flow analysis as verifier. For bpf-next we might
implement removal of such dead code and adjust branches
instead. Fix from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tuntap and similar devices can inject GSO packets. Accept type
VIRTIO_NET_HDR_GSO_UDP, even though not generating UFO natively.
Processes are expected to use feature negotiation such as TUNSETOFFLOAD
to detect supported offload types and refrain from injecting other
packets. This process breaks down with live migration: guest kernels
do not renegotiate flags, so destination hosts need to expose all
features that the source host does.
Partially revert the UFO removal from 182e0b6b5846~1..d9d30adf5677.
This patch introduces nearly(*) no new code to simplify verification.
It brings back verbatim tuntap UFO negotiation, VIRTIO_NET_HDR_GSO_UDP
insertion and software UFO segmentation.
It does not reinstate protocol stack support, hardware offload
(NETIF_F_UFO), SKB_GSO_UDP tunneling in SKB_GSO_SOFTWARE or reception
of VIRTIO_NET_HDR_GSO_UDP packets in tuntap.
To support SKB_GSO_UDP reappearing in the stack, also reinstate
logic in act_csum and openvswitch. Achieve equivalence with v4.13 HEAD
by squashing in commit 939912216fa8 ("net: skb_needs_check() removes
CHECKSUM_UNNECESSARY check for tx.") and reverting commit 8d63bee643f1
("net: avoid skb_warn_bad_offload false positives on UFO").
(*) To avoid having to bring back skb_shinfo(skb)->ip6_frag_id,
ipv6_proxy_select_ident is changed to return a __be32 and this is
assigned directly to the frag_hdr. Also, SKB_GSO_UDP is inserted
at the end of the enum to minimize code churn.
Tested
Booted a v4.13 guest kernel with QEMU. On a host kernel before this
patch `ethtool -k eth0` shows UFO disabled. After the patch, it is
enabled, same as on a v4.13 host kernel.
A UFO packet sent from the guest appears on the tap device:
host:
nc -l -p -u 8000 &
tcpdump -n -i tap0
guest:
dd if=/dev/zero of=payload.txt bs=1 count=2000
nc -u 192.16.1.1 8000 < payload.txt
Direct tap to tap transmission of VIRTIO_NET_HDR_GSO_UDP succeeds,
packets arriving fragmented:
./with_tap_pair.sh ./tap_send_ufo tap0 tap1
(from https://github.com/wdebruij/kerneltools/tree/master/tests)
Changes
v1 -> v2
- simplified set_offload change (review comment)
- documented test procedure
Link: http://lkml.kernel.org/r/<CAF=yD-LuUeDuL9YWPJD9ykOZ0QCjNeznPDr6whqZ9NGMNF12Mw@mail.gmail.com>
Fixes: fb652fdfe837 ("macvlan/macvtap: Remove NETIF_F_UFO advertisement.")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 6fa1ba61520576cf1346c4ff09a056f2950cb3bf partially
implemented the new ethtool API, by replacing get_settings()
with get_link_ksettings(). This breaks ethtool, since the
userspace tool (according to the new API specs) never tries
the legacy set() call, when the new get() call succeeds.
All attempts to chance some setting from userspace result in:
> Cannot set new settings: Operation not supported
Implement the missing set() call.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian reported a breakage with anycast routes due to commit
4832c30d5458 ("net: ipv6: put host and anycast routes on device with
address"). Prior to this commit anycast routes were added against the
loopback device causing repetitive route entries with no insight into
why they existed. e.g.:
$ ip -6 ro ls table local type anycast
anycast 2001:db8:1:: dev lo proto kernel metric 0 pref medium
anycast 2001:db8:2:: dev lo proto kernel metric 0 pref medium
anycast fe80:: dev lo proto kernel metric 0 pref medium
anycast fe80:: dev lo proto kernel metric 0 pref medium
The point of commit 4832c30d5458 is to add the routes using the device
with the address which is causing the route to be added. e.g.,:
$ ip -6 ro ls table local type anycast
anycast 2001:db8:1:: dev eth1 proto kernel metric 0 pref medium
anycast 2001:db8:2:: dev eth2 proto kernel metric 0 pref medium
anycast fe80:: dev eth2 proto kernel metric 0 pref medium
anycast fe80:: dev eth1 proto kernel metric 0 pref medium
For traffic to work as it did before, the dst device needs to be switched
to the loopback when the copy is created similar to local routes.
Fixes: 4832c30d5458 ("net: ipv6: put host and anycast routes on device with address")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ursula Braun says:
====================
net/smc: fixes for smc buffer handling
here are 2 cleanup patches for smc buffer handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With gcc-4.1.2:
net/smc/smc_core.c: In function ‘__smc_buf_create’:
net/smc/smc_core.c:567: warning: ‘bufsize’ may be used uninitialized in this function
Indeed, if the for-loop is never executed, bufsize is used
uninitialized. In addition, buf_desc is stored for later use, while it
is still a NULL pointer.
Before, error handling was done by checking if buf_desc is non-NULL.
The cleanup changed this to an error check, but forgot to update the
preinitialization of buf_desc to an error pointer.
Update the preinitializatin of buf_desc to fix this.
Fixes: b33982c3a6838d13 ("net/smc: cleanup function __smc_buf_create()")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3e034725c0d8 ("net/smc: common functions for RMBs and send buffers")
merged handling of SMC receive and send buffers. It introduced sk_buf_size
as merged start value for size determination. But since sk_buf_size is not
used at all, sk_sndbuf is erroneously used as start for rmb creation.
This patch makes sure, sk_buf_size is really used as intended, and
sk_rcvbuf is used as start value for rmb creation.
Fixes: 3e034725c0d8 ("net/smc: common functions for RMBs and send buffers")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the 'ignore_routes_with_linkdown' sysctl is set, we should not
consider linkdown nexthops during route lookup.
While the code correctly verifies that the initially selected route
('match') has a carrier, it does not perform the same check in the
subsequent multipath selection, resulting in a potential packet loss.
In case the chosen route does not have a carrier and the sysctl is set,
choose the initially selected route.
Fixes: 35103d11173b ("net: ipv6 sysctl option to ignore routes when nexthop link is down")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If you flush (delete) a filter chain other than chain 0 (such as when
deleting the device), the kernel may run into a use-after-free. The
chain refcount must not be decremented unless we are sure we are done
with the chain.
To reproduce the bug, run:
ip link add dtest type dummy
tc qdisc add dev dtest ingress
tc filter add dev dtest chain 1 parent ffff: flower
ip link del dtest
Introduced in: commit f93e1cdcf42c ("net/sched: fix filter flushing"),
but unless you have KAsan or luck, you won't notice it until
commit 0dadc117ac8b ("cls_flower: use tcf_exts_get_net() before call_rcu()")
Fixes: f93e1cdcf42c ("net/sched: fix filter flushing")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Roman Kapl <code@rkapl.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/phy/cortina.o
see include/linux/module.h for more information
This adds the license as "GPL", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux into timers/urgent
Pull the last batch of manual timer conversions from Kees Cook:
- final batch of "non trivial" timer conversions (multi-tree dependencies,
things Coccinelle couldn't handle, etc).
- treewide conversions via Coccinelle, in 4 steps:
- DEFINE_TIMER() functions converted to struct timer_list * argument
- init_timer() -> setup_timer()
- setup_timer() -> timer_setup()
- setup_timer() -> timer_setup() (with a single embedded structure)
- deprecated timer API removals (init_timer(), setup_*timer())
- finalization of new API (remove global casts)
|
|
$(real-objs-y) in only used in scripts/Makefile.build to form
"targets", but $(extra-y) is added to "targets" in another line.
We do not need to add $(extra-y) twice.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
*.i and *.lst are supported by the single target build. Clean up them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The "rpm" has been kept for backward compatibility since pre-git era.
I am planning to remove it after the Linux 4.18 release. Annouce the
end of the support, prompting to use "rpm-pkg" instead.
If you use "rpm", it will work like "rpm-pkg", but warning messages
will be displayed as follows:
WARNING: "rpm" target will be removed after Linux 4.18
Please use "rpm-pkg" instead.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
For rpm-pkg and deb-pkg, a source tar file is created. All paths in
the archive must be prefixed with the base name of the tar so that
everything is contained in the directory when you extract it.
Currently, scripts/package/Makefile uses a symlink for that, and
removes it after the tar is created.
If you terminate the build during the tar creation, the symlink is
left over. Then, at the next package build, you will see a warning
like follows:
ln: '.' and 'kernel-4.14.0+/.' are the same file
It is possible to fix it by adding -n (--no-dereference) option to
the "ln" command, but a cleaner way is to use --transform option
of "tar" command. This option is GNU extension, but it should not
hurt to use it in the Linux build system.
The 'S' flag is needed to exclude symlinks from the path fixup.
Without it, symlinks in the kernel are broken.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The command "make -j8 C=1 CHECK=scripts/coccicheck" produces
lots of "coccicheck failed" error messages.
Julia Lawall explained the Coccinelle behavior as follows:
"The problem on the Coccinelle side is that it uses a subdirectory
with the name of the semantic patch to store standard output and
standard error for the different threads. I didn't want to use a
name with the pid, so that one could easily find this information
while Coccinelle is running. Normally the subdirectory is cleaned
up when Coccinelle completes, so there is only one of them at a time.
Maybe it is best to just add the pid. There is the risk that these
subdirectories will accumulate if Coccinelle crashes in a way such
that they don't get cleaned up, but Coccinelle could print a warning
if it detects this case, rather than failing."
When scripts/coccicheck is used as CHECK tool and -j option is given
to Make, the whole of build process runs in parallel. So, multiple
processes try to get access to the same subdirectory.
I notice spatch creates the subdirectory only when it runs in parallel
(i.e. --jobs <N> is given and <N> is greater than 1).
Setting NPROC=1 is a reasonable solution; spatch does not create the
subdirectory. Besides, ONLINE=1 mode takes a single file input for
each spatch invocation, so there is no reason to parallelize it in
the first place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Julia Lawall <Julia.Lawall@lip6.fr>
|
|
sym_arr is of type struct symbol **.
So in malloc we need sizeof(struct symbol *).
The problem was indicated by coccinelle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
when the verifier detects that register contains a runtime constant
and it's compared with another constant it will prune exploration
of the branch that is guaranteed not to be taken at runtime.
This is all correct, but malicious program may be constructed
in such a way that it always has a constant comparison and
the other branch is never taken under any conditions.
In this case such path through the program will not be explored
by the verifier. It won't be taken at run-time either, but since
all instructions are JITed the malicious program may cause JITs
to complain about using reserved fields, etc.
To fix the issue we have to track the instructions explored by
the verifier and sanitize instructions that are dead at run time
with NOPs. We cannot reject such dead code, since llvm generates
it for valid C code, since it doesn't do as much data flow
analysis as the verifier does.
Fixes: 17a5267067f3 ("bpf: verifier (add verifier core)")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This commit adds PCI ID for Raven platform
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It maybe the typo for ALC700 support patch.
To fix the bit value on this patch.
Fixes: 6fbae35a3170 ("ALSA: hda/realtek - Add support for new codecs ALC700/ALC701/ALC703")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The changes for this release include power management improvements for
the pwm-img driver, support for the backup mode on pwm-atmel-tcb as
well as support for more hardware with the R-Car and Mediatek drivers.
To round things off there's a bit of cleanup for sunxi and stm32-lp"
* tag 'pwm/for-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: stm32-lp: Remove pwm_is_enabled() check before calling pwm_disable()
pwm: mediatek: Add MT2712/MT7622 support
pwm: sunxi: Use of_device_get_match_data()
pwm: atmel-tcb: Support backup mode
dt-bindings: pwm: Add R-Car D3 device tree bindings
pwm: img: Add runtime PM
pwm: img: Add suspend / resume handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"There is nothing scary this cycle, mostly driver fixes and updates.
The core fix has been in for a while and has been tested on multiple
kernel revisions by multiple teams.
Core:
- Fix setting the alarm to the next expiring timer
New drivers:
- Mediatek MT7622 RTC
- NXP PCF85363
- Spreadtrum SC27xx PMIC RTC
Drivers updates:
- Use generic nvmem to expose the Non volatile ram for ds1305,
ds1511, m48t86 and omap
- abx80x: solve possible race condition at probe
- armada38x: support trimming the RTC oscillator
- at91rm9200: fix reading the alarm value at boot
- ds1511: allow waking platform
- m41t80: rework square wave output
- pcf8523: support trimming the RTC oscillator
- pcf8563: fix clock output rate
- pl031: make interrupt optional
- xgene: fix suspend/resume"
* tag 'rtc-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
dt-bindings: rtc: imxdi: Improve the bindings text
rtc: sc27xx: Add Spreadtrum SC27xx PMIC RTC driver
dt-bindings: rtc: Add Spreadtrum SC27xx RTC documentation
rtc: at91rm9200: fix reading alarm value
rtc: at91rm9200: stop calculating yday in at91_rtc_readalarm
rtc: sysfs: Use time64_t variables to set time/alarm
rtc: xgene: mark PM functions as __maybe_unused
rtc: xgene: Fix suspend/resume
rtc: pcf8563: don't alway enable the alarm
rtc: pcf8563: fix output clock rate
rtc: rx8010: Fix for incorrect return value
rtc: rx8010: Specify correct address for RX8010_RESV31
rtc: rx8010: Remove duplicate define
rtc: m41t80: remove unneeded checks from m41t80_sqw_set_rate
rtc: m41t80: avoid i2c read in m41t80_sqw_is_prepared
rtc: m41t80: avoid i2c read in m41t80_sqw_recalc_rate
rtc: m41t80: fix m41t80_sqw_round_rate return value
rtc: m41t80: m41t80_sqw_set_rate should return 0 on success
rtc: add support for NXP PCF85363 real-time clock
rtc: omap: Support scratch registers
...
|
|
Running this code with IRQs enabled (where dummy_lock is a spinlock):
static void check_load_gs_index(void)
{
/* This will fail. */
load_gs_index(0xffff);
spin_lock(&dummy_lock);
spin_unlock(&dummy_lock);
}
Will generate a lockdep warning. The issue is that the actual write
to %gs would cause an exception with IRQs disabled, and the exception
handler would, as an inadvertent side effect, update irqflag tracing
to reflect the IRQs-off status. native_load_gs_index() would then
turn IRQs back on and return with irqflag tracing still thinking that
IRQs were off. The dummy lock-and-unlock causes lockdep to notice the
error and warn.
Fix it by adding the missing tracing.
Apparently nothing did this in a context where it mattered. I haven't
tried to find a code path that would actually exhibit the warning if
appropriately nasty user code were running.
I suspect that the security impact of this bug is very, very low --
production systems don't run with lockdep enabled, and the warning is
mostly harmless anyway.
Found during a quick audit of the entry code to try to track down an
unrelated bug that Ingo found in some still-in-development code.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/e1aeb0e6ba8dd430ec36c8a35e63b429698b4132.1511411918.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull MTD updates from Richard Weinberger:
"General changes:
- Unconfuse get_unmapped_area and point/unpoint driver methods
- New partition parser: sharpslpart
- Kill GENERIC_IO
- Various fixes
NAND changes:
- Add a flag to mark NANDs that require 3 address cycles to encode a
page address
- Set a default ECC/free layout when NAND_ECC_NONE is requested
- Fix a bug in panic_nand_write()
- Another batch of cleanups for the denali driver
- Fix PM support in the atmel driver
- Remove support for platform data in the omap driver
- Fix subpage write in the omap driver
- Fix irq handling in the mtk driver
- Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
- Change log level of ECC error messages in the mxc driver
- Patch the pxa3xx driver to support Armada 8k platforms
- Add BAM DMA support to the qcom driver
- Convert gpio-nand to the GPIO desc API
- Fix ECC handling in the mt29f driver
SPI-NOR changes:
- Introduce system power management support
- New mechanism to select the proper .quad_enable() hook by JEDEC
ID, when needed, instead of only by manufacturer ID
- Add support to new memory parts from Gigadevice, Winbond, Macronix
and Everspin
- Maintainance for Cadence, Intel, Mediatek and STM32 drivers"
* tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd: (85 commits)
mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid
mtd: sharpslpart: Add sharpslpart partition parser
mtd: Add sanity checks in mtd_write/read_oob()
mtd: remove the get_unmapped_area method
mtd: implement mtd_get_unmapped_area() using the point method
mtd: chips/map_rom.c: implement point and unpoint methods
mtd: chips/map_ram.c: implement point and unpoint methods
mtd: mtdram: properly handle the phys argument in the point method
mtd: mtdswap: fix spelling mistake: 'TRESHOLD' -> 'THRESHOLD'
mtd: slram: use memremap() instead of ioremap()
kconfig: kill off GENERIC_IO option
mtd: Fix C++ comment in include/linux/mtd/mtd.h
mtd: constify mtd_partition
mtd: plat-ram: Replace manual resource management by devm
mtd: nand: Fix writing mtdoops to nand flash.
mtd: intel-spi: Add Intel Lewisburg PCH SPI super SKU PCI ID
mtd: nand: mtk: fix infinite ECC decode IRQ issue
mtd: spi-nor: Add support for mr25h128
mtd: nand: mtk: change the compile sequence of mtk_nand.o and mtk_ecc.o
mtd: spi-nor: enable 4B opcodes for mx66l51235l
...
|
|
Pull xfs fixes from Darrick Wong:
- Fix a memory leak in the new in-core extent map
- Refactor the xfs_dev_t conversions for easier xfsprogs porting
* tag 'xfs-4.15-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: abstract out dev_t conversions
xfs: fix memory leak in xfs_iext_free_last_leaf
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull mode_t whack-a-mole from Al Viro:
"For all internal uses we want umode_t, which is arch-independent;
mode_t (or __kernel_mode_t, for that matter) is wrong outside of
userland ABI.
Unfortunately, that crap keeps coming back and needs to be put down
from time to time..."
* 'work.whack-a-mole' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
mode_t whack-a-mole: task_dump_owner()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull 9p filesystemfixes from Al Viro:
"Several 9p fixes"
* '9p-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
9p: Fix missing commas in mount options
net/9p: Switch to wait_event_killable()
fs/9p: Compare qid.path in v9fs_test_inode
|
|
Set the clang KBUILD_CFLAGS up before including arch/ Makefiles,
so that ld-options (etc.) can work correctly.
This fixes errors with clang such as ld-options trying to CC
against your host architecture, but LD trying to link against
your target architecture.
Signed-off-by: Chris Fries <cfries@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
I think this snuck in when I applied the patch for f97decac5f4c (didn't
apply cleanly, required some manual applying + git-add). It is unused
and shouldn't be here. My bad.
Fixes: f97decac5f4c "drm/msm: Support multiple ringbuffers"
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This uses the EDID info from my HTC Vive to mark it as
non-desktop.
v2: Change description from non-standard to non-desktop
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We don't want fbcon to get used on non-desktop dislays,
don't pass them as enabled connectors to the fb helper setup.
This prevents my HMD from getting disorted fbcon, and from
affecting other displays console.
v2: Change description from non-standard to non-desktop
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This adds the infrastructure needed to quirk displays
using edid and to mark them a non-desktop.
A non-desktop display is one which shouldn't normally be included
as a part of a desktop environment.
This is meant to cover head mounted devices like HTC Vive.
v2: Change description from non-standard to non-desktop, add docs
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fixup docs
|
|
tilcdc fixes for v4.15
* tag 'tilcdc-4.15-fixes' of https://github.com/jsarha/linux:
drm/tilcdc: Remove obsolete "ti,tilcdc,slave" dts binding support
|
|
into drm-next
more misc amdgpu fixes.
* 'drm-next-4.15' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: fix rmmod KCQ disable failed error
drm/amdgpu: fix kernel hang when starting VNC server
drm/amdgpu: don't skip attributes when powerplay is enabled
drm/amd/pp: fix typecast error in powerplay.
Revert "drm/radeon: dont switch vt on suspend"
drm/amd/amdgpu: fix over-bound accessing in amdgpu_cs_wait_any_fence
drm/amd/powerplay: fix unfreeze level smc message for smu7
drm/amdgpu:fix memleak
drm/amdgpu:fix memleak in takedown
|
|
git://git.pengutronix.de/git/pza/linux into drm-next
drm/imx: various cleanups
- Switch to drm_*_get/put() helpers
- Use correct parallel-display connector enum: DPI instead of VGA
- Remove incorrect unit name from device tree binding documentation example
- Remove an unused variable
* tag 'imx-drm-next-2017-10-18' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-v3: ipu-dc: Remove unused 'di' variable
dt-bindings: fsl-imx-drm: Remove incorrect "@di0" usage
drm/imx: parallel-display: use correct connector enum
drm/imx: switch to drm_*_get(), drm_*_put() helpers
|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Fixes for v4.15-rc1
This includes an update to the SOR pad clock programming needed because
of some changes that went in through the clock tree.
* tag 'drm/tegra/for-4.15-rc1-fixes' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: sor: Reimplement pad clock
|
|
Gianluca Borello says:
====================
This set includes some fixes in semantics and usability issues that emerged
recently, and would be good to have them in net before the next release.
In particular, ARG_CONST_SIZE_OR_ZERO semantics was recently changed in
commit 9fd29c08e520 ("bpf: improve verifier ARG_CONST_SIZE_OR_ZERO
semantics") with the goal of letting the compiler generate simpler code
that the verifier can more easily accept.
To handle this change in semantics, a few checks in some helpers were
added, like in commit 9c019e2bc4b2 ("bpf: change helper bpf_probe_read arg2
type to ARG_CONST_SIZE_OR_ZERO"), and those checks are less than ideal
because once they make it into a released kernel bpf programs can start
relying on them, preventing the possibility of being removed later on.
This patch tries to fix the issue by introducing a new argument type
ARG_PTR_TO_MEM_OR_NULL that can be used for helpers that can receive a
<NULL, 0> tuple. By doing so, we can fix the semantics of the other helpers
that don't need <NULL, 0> and can just handle <!NULL, 0>, allowing the code
to get rid of those checks.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Commit 9fd29c08e520 ("bpf: improve verifier ARG_CONST_SIZE_OR_ZERO
semantics") relaxed the treatment of ARG_CONST_SIZE_OR_ZERO due to the way
the compiler generates optimized BPF code when checking boundaries of an
argument from C code. A typical example of this optimized code can be
generated using the bpf_perf_event_output helper when operating on variable
memory:
/* len is a generic scalar */
if (len > 0 && len <= 0x7fff)
bpf_perf_event_output(ctx, &perf_map, 0, buf, len);
110: (79) r5 = *(u64 *)(r10 -40)
111: (bf) r1 = r5
112: (07) r1 += -1
113: (25) if r1 > 0x7ffe goto pc+6
114: (bf) r1 = r6
115: (18) r2 = 0xffff94e5f166c200
117: (b7) r3 = 0
118: (bf) r4 = r7
119: (85) call bpf_perf_event_output#25
R5 min value is negative, either use unsigned or 'var &= const'
With this code, the verifier loses track of the variable.
Replacing arg5 with ARG_CONST_SIZE_OR_ZERO is thus desirable since it
avoids this quite common case which leads to usability issues, and the
compiler generates code that the verifier can more easily test:
if (len <= 0x7fff)
bpf_perf_event_output(ctx, &perf_map, 0, buf, len);
or
bpf_perf_event_output(ctx, &perf_map, 0, buf, len & 0x7fff);
No changes to the bpf_perf_event_output helper are necessary since it can
handle a case where size is 0, and an empty frame is pushed.
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Commit 9fd29c08e520 ("bpf: improve verifier ARG_CONST_SIZE_OR_ZERO
semantics") relaxed the treatment of ARG_CONST_SIZE_OR_ZERO due to the way
the compiler generates optimized BPF code when checking boundaries of an
argument from C code. A typical example of this optimized code can be
generated using the bpf_probe_read_str helper when operating on variable
memory:
/* len is a generic scalar */
if (len > 0 && len <= 0x7fff)
bpf_probe_read_str(p, len, s);
251: (79) r1 = *(u64 *)(r10 -88)
252: (07) r1 += -1
253: (25) if r1 > 0x7ffe goto pc-42
254: (bf) r1 = r7
255: (79) r2 = *(u64 *)(r10 -88)
256: (bf) r8 = r4
257: (85) call bpf_probe_read_str#45
R2 min value is negative, either use unsigned or 'var &= const'
With this code, the verifier loses track of the variable.
Replacing arg2 with ARG_CONST_SIZE_OR_ZERO is thus desirable since it
avoids this quite common case which leads to usability issues, and the
compiler generates code that the verifier can more easily test:
if (len <= 0x7fff)
bpf_probe_read_str(p, len, s);
or
bpf_probe_read_str(p, len & 0x7fff, s);
No changes to the bpf_probe_read_str helper are necessary since
strncpy_from_unsafe itself immediately returns if the size passed is 0.
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Commit 9c019e2bc4b2 ("bpf: change helper bpf_probe_read arg2 type to
ARG_CONST_SIZE_OR_ZERO") changed arg2 type to ARG_CONST_SIZE_OR_ZERO to
simplify writing bpf programs by taking advantage of the new semantics
introduced for ARG_CONST_SIZE_OR_ZERO which allows <!NULL, 0> arguments.
In order to prevent the helper from actually passing a NULL pointer to
probe_kernel_read, which can happen when <NULL, 0> is passed to the helper,
the commit also introduced an explicit check against size == 0.
After the recent introduction of the ARG_PTR_TO_MEM_OR_NULL type,
bpf_probe_read can not receive a pair of <NULL, 0> arguments anymore, thus
the check is not needed anymore and can be removed, since probe_kernel_read
can correctly handle a <!NULL, 0> call. This also fixes the semantics of
the helper before it gets officially released and bpf programs start
relying on this check.
Fixes: 9c019e2bc4b2 ("bpf: change helper bpf_probe_read arg2 type to ARG_CONST_SIZE_OR_ZERO")
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
With the current ARG_PTR_TO_MEM/ARG_PTR_TO_UNINIT_MEM semantics, an helper
argument can be NULL when the next argument type is ARG_CONST_SIZE_OR_ZERO
and the verifier can prove the value of this next argument is 0. However,
most helpers are just interested in handling <!NULL, 0>, so forcing them to
deal with <NULL, 0> makes the implementation of those helpers more
complicated for no apparent benefits, requiring them to explicitly handle
those corner cases with checks that bpf programs could start relying upon,
preventing the possibility of removing them later.
Solve this by making ARG_PTR_TO_MEM/ARG_PTR_TO_UNINIT_MEM never accept NULL
even when ARG_CONST_SIZE_OR_ZERO is set, and introduce a new argument type
ARG_PTR_TO_MEM_OR_NULL to explicitly deal with the NULL case.
Currently, the only helper that needs this is bpf_csum_diff_proto(), so
change arg1 and arg3 to this new type as well.
Also add a new battery of tests that explicitly test the
!ARG_PTR_TO_MEM_OR_NULL combination: all the current ones testing the
various <NULL, 0> variations are focused on bpf_csum_diff, so cover also
other helpers.
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
I got the logic wrong in the DT CPU features code when I added the
Power9 DD2.1 feature. We should be setting the bit if we detect a
DD2.1, not clearing it if we detect a DD2.0.
This code isn't actually exercised at the moment so nothing is
actually broken.
Fixes: 3ffa9d9e2a7c ("powerpc/64s: Fix Power9 DD2.0 workarounds by adding DD2.1 feature")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
IMC_MAX_PMU is used for static storage (per_nest_pmu_arr) which holds
nest pmu information. Current value for the macro is 32 based on
the initial number of nest pmu units supported by the nest microcode.
But going forward, microcode could support more nest units. Instead
of static storage, patch to fix the code to dynamically allocate an
array based on the number of nest imc units found in the device tree.
Fixes:8f95faaac56c1 ('powerpc/powernv: Detect and create IMC device')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
"pmu_count" in opal_imc_counters_probe() is intended to hold
the number of successful nest imc pmu registerations. But
current code also counts other imc units like core_imc and
thread_imc. Patch add a check to count only nest imc pmus.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
On powerpc32, patch_instruction() is called by apply_feature_fixups()
which is called from early_init()
There is the following note in front of early_init():
* Note that the kernel may be running at an address which is different
* from the address that it was linked at, so we must use RELOC/PTRRELOC
* to access static data (including strings). -- paulus
Therefore, slab_is_available() cannot be called yet, and
text_poke_area must be addressed with PTRRELOC()
Fixes: 95902e6c8864 ("powerpc/mm: Implement STRICT_KERNEL_RWX on PPC32")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The previous fix for addressing the breakage in vmaster slave
initialization, commit a91d66129fb9 ("ALSA: hda - Fix incorrect TLV
callback check introduced during set_fs() removal"), introduced a new
helper to process over each slave kctl. However, this helper passes
only the original kctl, not the virtual slave kctl. As a result,
HD-audio driver (which is the only user so far) couldn't initialize
the slave correctly because it's trying to update the value directly
with the original kctl, not with the mapped kctl.
This patch fixes the situation again by passing both the mapped slaved
and original slave kctls to the function. Luckily there is a single
caller as of now, so changing the call signature is no big matter.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=197959
Fixes: a91d66129fb9 ("ALSA: hda - Fix incorrect TLV callback check introduced during set_fs() removal")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40evf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
