| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Down-speed auto-negotiation may not always be enabled, in which case the
PHY won't down-shift to 100 or 10 during auto-negotiation.
This change enables downshift and configures the number of retries to
default 4 (which is also in the datasheet
The downshift control mechanism can also be controlled via the phy-tunable
interface (ETHTOOL_PHY_DOWNSHIFT control).
The change has been adapted from the Aquantia PHY driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ADIN PHYs supports 4 types of reset:
1. The standard PHY reset via BMCR_RESET bit in MII_BMCR reg
2. Reset via GPIO
3. Reset via reg GeSftRst (0xff0c) & reload previous pin configs
4. Reset via reg GeSftRst (0xff0c) & request new pin configs
Resets 2, 3 & 4 are almost identical, with the exception that the crystal
oscillator is available during reset for 2.
This change implements subsystem software reset via the GeSftRst and
reloading the previous pin configuration (so reset number 3).
This will also reset the PHY core regs (similar to reset 1).
Since writing bit 1 to reg GeSftRst is self-clearing, the only thing that
can be done, is to write to that register, wait a specific amount of time
(10 milliseconds should be enough) and try to read back and check if there
are no errors on read. A busy-wait-read won't work well, and may sometimes
work or not work.
In case phylib is configured to also do a reset via GPIO, the ADIN PHY may
be reset twice when the PHY device registers, but that isn't a problem,
since it's being done on boot (or PHY device register).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ADIN1200 & ADIN1300 PHYs support EEE by using standard Clause 45 access
to access MMD registers for EEE.
The EEE register addresses (when using Clause 22) are available at
different addresses (than Clause 45), and since accessing these regs (via
Clause 22) needs a special mechanism, a translation table is required to
convert these addresses.
For Clause 45, this is not needed since the driver will likely never use
this access mode.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ADIN PHYs support automatic MDI/MDIX negotiation. By default this is
disabled, so this is enabled at `config_init`.
This is controlled via the PHY Control 1 register.
The supported modes are:
1. Manual MDI
2. Manual MDIX
3. Auto MDIX - prefer MDIX
4. Auto MDIX - prefer MDI
The phydev mdix & mdix_ctrl fields include modes 3 & 4 into a single
auto-mode. So, the default mode this driver enables is 4 when Auto-MDI mode
is used.
When detecting MDI/MDIX mode, a combination of the PHY Control 1 register
and PHY Status 1 register is used to determine the correct MDI/MDIX mode.
If Auto-MDI mode is not set, then the manual MDI/MDIX mode is returned.
If Auto-MDI mode is set, then MDIX mode is returned differs from the
preferred MDI/MDIX mode.
This covers all cases where:
1. MDI preferred & Pair01Swapped == MDIX
2. MDIX preferred & Pair01Swapped == MDI
3. MDI preferred & ! Pair01Swapped == MDIX
4. MDIX preferred & ! Pair01Swapped == MDI
The preferred MDI/MDIX mode is not configured via SW, but can be configured
via HW pins. Note that the `Pair01Swapped` is the Green-Yellow physical
pairs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FIFO depth can be configured for the RMII mode. This change adds
support for doing this via device-tree (or ACPI).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal delays for the RGMII are configurable for both RX & TX. This
change adds support for configuring them via device-tree (or ACPI).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ADIN1300 chip supports RGMII, RMII & MII modes. Default (if
unconfigured) is RGMII.
This change adds support for configuring these modes via the device
registers.
For RGMII with internal delays (modes RGMII_ID,RGMII_TXID, RGMII_RXID),
the default delay is 2 ns. This can be configurable and will be done in
a subsequent change.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both ADIN1200 & ADIN1300 support Clause 45 access for some registers.
The Extended Management Interface (EMI) registers are accessible via both
Clause 45 (at register MDIO_MMD_VEND1) and using Clause 22.
The Clause 22 access for MMD regs differs from the standard one defined by
802.3. The ADIN PHYs use registers ExtRegPtr (0x0010) and ExtRegData
(0x0011) to access Clause 45 & EMI registers.
The indirect access is done via the following mechanism (for both R/W):
1. Write the address of the register in the ExtRegPtr
2. Read/write the value of the register via reg ExtRegData
This mechanism is needed to manage configuration of chip settings and to
access EEE registers via Clause 22.
Since Clause 45 access will likely never be used, it is not implemented via
this hook.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change hooks link-status-change interrupts to phylib.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The chip supports standard suspend/resume via BMCR reg.
Hook these functions into the `adin` driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change adds support for Analog Devices Industrial Ethernet PHYs.
Particularly the PHYs this driver adds support for:
* ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY
* ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
The 2 chips are register compatible with one another. The main difference
being that ADIN1200 doesn't operate in gigabit mode.
The chips can be operated by the Generic PHY driver as well via the
standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the
kernel as well. This assumes that configuration of the PHY has been done
completely in HW, according to spec.
Configuration can also be done via registers, which will be supported by
this driver.
Datasheets:
https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1300.pdf
https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1200.pdf
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Don't taint the kernel if CPUs have different sets of page sizes
supported (other than the one in use).
- Issue I-cache maintenance for module ftrace trampoline.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ftrace: Ensure module ftrace trampoline is coherent with I-side
arm64: cpufeature: Don't treat granule sizes as strict
|
|
The initial support for dynamic ftrace trampolines in modules made use
of an indirect branch which loaded its target from the beginning of
a special section (e71a4e1bebaf7 ("arm64: ftrace: add support for far
branches to dynamic ftrace")). Since no instructions were being patched,
no cache maintenance was needed. However, later in be0f272bfc83 ("arm64:
ftrace: emit ftrace-mod.o contents through code") this code was reworked
to output the trampoline instructions directly into the PLT entry but,
unfortunately, the necessary cache maintenance was overlooked.
Add a call to __flush_icache_range() after writing the new trampoline
instructions but before patching in the branch to the trampoline.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: James Morse <james.morse@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: be0f272bfc83 ("arm64: ftrace: emit ftrace-mod.o contents through code")
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These add a check to avoid recent suspend-to-idle power regression on
systems with NVMe drives where the PCIe ASPM policy is "performance"
(or when the kernel is built without ASPM support), fix an issue
related to frequency limits in the schedutil cpufreq governor and fix
a mistake related to the PM QoS usage in the cpufreq core introduced
recently.
Specifics:
- Disable NVMe power optimization related to suspend-to-idle added
recently on systems where PCIe ASPM is not able to put PCIe links
into low-power states to prevent excess power from being drawn by
the system while suspended (Rafael Wysocki).
- Make the schedutil governor handle frequency limits changes
properly in all cases (Viresh Kumar).
- Prevent the cpufreq core from treating positive values returned by
dev_pm_qos_update_request() as errors (Viresh Kumar)"
* tag 'pm-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
nvme-pci: Allow PCI bus-level PM to be used if ASPM is disabled
PCI/ASPM: Add pcie_aspm_enabled()
cpufreq: schedutil: Don't skip freq update when limits change
cpufreq: dev_pm_qos_update_request() can return 1 on success
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Fixes in dmaengine drivers for:
- dw-edma: endianess, _iomem type and stack usages
- ste_dma40: unneeded variable and null-pointer dereference
- tegra210-adma: unused function
- omap-dma: off-by-one fix"
* tag 'dmaengine-fix-5.3-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
omap-dma/omap_vout_vrfb: fix off-by-one fi value
dmaengine: stm32-mdma: Fix a possible null-pointer dereference in stm32_mdma_irq_handler()
dmaengine: tegra210-adma: Fix unused function warnings
dmaengine: ste_dma40: fix unneeded variable warning
dmaengine: dw-edma: fix endianess confusion
dmaengine: dw-edma: fix __iomem type confusion
dmaengine: dw-edma: fix unnecessary stack usage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All small fixes targeted for stable:
- Two fixes for USB-audio with malformed descriptor, spotted by
fuzzers
- Two fixes Conexant HD-audio codec wrt power management
- Quirks for HD-audio AMD platform and HP laptop
- HD-audio memory leak fix"
* tag 'sound-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Fix a stack buffer overflow bug in check_input_term
ALSA: usb-audio: Fix an OOB bug in parse_audio_mixer_unit
ALSA: hda - Add a generic reboot_notify
ALSA: hda - Let all conexant codec enter D3 when rebooting
ALSA: hda/realtek - Add quirk for HP Envy x360
ALSA: hda - Fix a memory leak bug
ALSA: hda - Apply workaround for another AMD chip 1022:1487
|
|
Pull drm fixes from Dave Airlie:
"Nothing too crazy this week, one amdgpu fix to use vmalloc for a
struct that grew in size, and another MST fix for nouveau, and some
other misc fixes:
i915:
- single GVT use after free fix
scheduler:
- entity destruction race fix
amdgpu:
- struct allocation fix
- gfx9 soft recovery fix
nouveau:
- followup MST fix
ast:
- vga register race fix"
* tag 'drm-fixes-2019-08-16' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau: Only recalculate PBN/VCPI on mode/connector changes
drm/ast: Fixed reboot test may cause system hanged
drm/scheduler: use job count instead of peek
drm/amd/display: use kvmalloc for dc_state (v2)
drm/amdgpu: fix gfx9 soft recovery
drm/i915: Use after free in error path in intel_vgpu_create_workload()
|
|
* pm-cpufreq:
cpufreq: schedutil: Don't skip freq update when limits change
cpufreq: dev_pm_qos_update_request() can return 1 on success
|
|
Recent gcc compilers (gcc 9.1) generate warnings about an out of bounds
memset, if the memset goes accross several fields of a struct. This
generated a couple of warnings on x86_64 builds in sanitize_boot_params().
Fix this by explicitly saving the fields in struct boot_params
that are intended to be preserved, and zeroing all the rest.
[ tglx: Tagged for stable as it breaks the warning free build there as well ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190731054627.5627-2-jhubbard@nvidia.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-linus
Vinod writes:
soundwire fixes for v5.3-rc5
Pierre sent fixes which are queued now for v5.3-rc5 are:
- regmap dependecy
- cadence register definitions
* tag 'soundwire-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: fix regmap dependencies and align with other serial links
soundwire: cadence_master: fix definitions for INTSTAT0/1
soundwire: cadence_master: fix register definition for SLAVE_STATE
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.4-rc5:
- GVT use-after-free fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87zhkag9ic.fsf@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fix local endpoint handling
Here's a pair of patches that fix two issues in the handling of local
endpoints (rxrpc_local structs):
(1) Use list_replace_init() rather than list_replace() if we're going to
unconditionally delete the replaced item later, lest the list get
corrupted.
(2) Don't access the rxrpc_local object after passing our ref to the
workqueue, not even to illuminate tracepoints, as the work function
may cause the object to be freed. We have to cache the information
beforehand.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Antoine Tenart says:
====================
net: mscc: PTP Hardware Clock (PHC) support
This series introduces the PTP Hardware Clock (PHC) support to the Mscc
Ocelot switch driver. In order to make use of this, a new register bank
is added and described in the device tree, as well as a new interrupt.
The use this bank and interrupt was made optional in the driver for dt
compatibility reasons.
Thanks!
Antoine
Since v5:
- Made sure both the PTP interrupt and register bank were available to
enable supporting h/w timestamping.
- Added a check after a kzalloc.
- Add Reviewed-by tags from Andrew.
Since v4:
- Added SKBTX_IN_PROGRESS.
- Fixed two xmas trees.
- Rework the loop condition in ocelot_ptp_rdy_irq_handler.
Since v3:
- Fixed a spin_unlock_irqrestore issue.
Since v2:
- Prevented from a possible infinite loop when reading the h/w
timestamps.
- s/GFP_KERNEL/GFP_ATOMIC/ in the Tx path.
- Set rx_filter to HWTSTAMP_FILTER_PTP_V2_EVENT at probe.
- Fixed s/w timestamping dependencies.
- Added Paul Burton's Acked-by on patches 2 and 4.
Since v1:
- Used list_for_each_safe() in ocelot_deinit().
- Fixed a memory leak in ocelot_deinit() by calling
dev_kfree_skb_any().
- Fixed a locking issue in get_hwtimestamp().
- Handled the NULL case of ptp_clock_register().
- Added comments on optional dt properties.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for PTP Hardware Clock (PHC) to the Ocelot
switch for both PTP 1-step and 2-step modes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In struct frame_info, the cpuq member is never used. This cosmetic patch
removes it from the structure, and from the parsing of the frame header
as it's only set but never used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This cosmetic patch improves the frame header parsing readability by
introducing a new macro to access and mask its fields.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for using the PTP register range, and adds a
description of its registers. This bank is used when configuring PTP.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One additional interrupt needs to be described within the Ocelot device
tree node: the PTP ready one. This patch documents the binding needed to
do so.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One additional register range needs to be described within the Ocelot
device tree node: the PTP. This patch documents the binding needed to do
so.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This patchset contains Netfilter fixes for net:
1) Extend selftest to cover flowtable with ipsec, from Florian Westphal.
2) Fix interaction of ipsec with flowtable, also from Florian.
3) User-after-free with bound set to rule that fails to load.
4) Adjust state and timeout for flows that expire.
5) Timeout update race with flows in teardown state.
6) Ensure conntrack id hash calculation use invariants as input,
from Dirk Morris.
7) Do not push flows into flowtable for TCP fin/rst packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
packet_sendmsg() checks tx_ring.pg_vec to decide
if it must call tpacket_snd().
Problem is that the check is lockless, meaning another thread
can issue a concurrent setsockopt(PACKET_TX_RING ) to flip
tx_ring.pg_vec back to NULL.
Given that tpacket_snd() grabs pg_vec_lock mutex, we can
perform the check again to solve the race.
syzbot reported :
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 11429 Comm: syz-executor394 Not tainted 5.3.0-rc4+ #101
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:packet_lookup_frame+0x8d/0x270 net/packet/af_packet.c:474
Code: c1 ee 03 f7 73 0c 80 3c 0e 00 0f 85 cb 01 00 00 48 8b 0b 89 c0 4c 8d 24 c1 48 b8 00 00 00 00 00 fc ff df 4c 89 e1 48 c1 e9 03 <80> 3c 01 00 0f 85 94 01 00 00 48 8d 7b 10 4d 8b 3c 24 48 b8 00 00
RSP: 0018:ffff88809f82f7b8 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffff8880a45c7030 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 1ffff110148b8e06 RDI: ffff8880a45c703c
RBP: ffff88809f82f7e8 R08: ffff888087aea200 R09: fffffbfff134ae50
R10: fffffbfff134ae4f R11: ffffffff89a5727f R12: 0000000000000000
R13: 0000000000000001 R14: ffff8880a45c6ac0 R15: 0000000000000000
FS: 00007fa04716f700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa04716edb8 CR3: 0000000091eb4000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
packet_current_frame net/packet/af_packet.c:487 [inline]
tpacket_snd net/packet/af_packet.c:2667 [inline]
packet_sendmsg+0x590/0x6250 net/packet/af_packet.c:2975
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:657
___sys_sendmsg+0x3e2/0x920 net/socket.c:2311
__sys_sendmmsg+0x1bf/0x4d0 net/socket.c:2413
__do_sys_sendmmsg net/socket.c:2442 [inline]
__se_sys_sendmmsg net/socket.c:2439 [inline]
__x64_sys_sendmmsg+0x9d/0x100 net/socket.c:2439
do_syscall_64+0xfd/0x6a0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: 69e3c75f4d54 ("net: TX_RING and packet mmap")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sudarsana Reddy Kalluru says:
====================
qed*: Support for NVM config attributes.
The patch series adds support for managing the NVM config attributes.
Patch (1) adds functionality to update config attributes via MFW.
Patch (2) adds driver interface for updating the config attributes.
Changes from previous versions:
-------------------------------
v4: Added more details on the functionality and its usage.
v3: Removed unused variable.
v2: Removed unused API.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds driver interface for reading the config attributes from user
provided buffer, and updates these values on nvm config flash partition.
This is basically an expansion of our existing ethtool -f implementation.
The management FW has exposed an additional method of configuring some of
the nvram options, and this makes use of that. This implementation will
come into use when newer FW files which contain configuration directives
employing this API will be provided to ethtool -f.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds API for configuring the NVM config attributes using
Management FW (MFW) interfaces.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
`check_input_term` recursively calls itself with input from
device side (e.g., uac_input_terminal_descriptor.bCSourceID)
as argument (id). In `check_input_term`, if `check_input_term`
is called with the same `id` argument as the caller, it triggers
endless recursive call, resulting kernel space stack overflow.
This patch fixes the bug by adding a bitmap to `struct mixer_build`
to keep track of the checked ids and stop the execution if some id
has been checked (similar to how parse_audio_unit handles unitid
argument).
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In myri10ge_probe(), myri10ge_alloc_slices() is invoked to allocate slices
related structures. Later on, myri10ge_request_irq() is used to get an irq.
However, if this process fails, the allocated slices related structures are
not deallocated, leading to memory leaks. To fix this issue, revise the
target label of the goto statement to 'abort_with_slices'.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2019-08-14
this is a pull request for net-next/master consisting of 41 patches.
The first two patches are for the kvaser_pciefd driver: Christer Beskow
removes unnecessary code in the kvaser_pciefd_pwm_stop() function,
YueHaibing removes the unused including of <linux/version.h>.
In the next patch YueHaibing also removes the unused including of
<linux/version.h> in the f81601 driver.
In the ti_hecc driver the next 6 patches are by me and fix checkpatch
warnings. YueHaibing's patch removes an unused variable in the
ti_hecc_mailbox_read() function.
The next 6 patches all target the xilinx_can driver. Anssi Hannula's
patch fixes a chip start failure with an invalid bus. The patch by
Venkatesh Yadav Abbarapu skips an error message in case of a deferred
probe. The 3 patches by Appana Durga Kedareswara rao fix the RX and TX
path for CAN-FD frames. Srinivas Neeli's patch fixes the bit timing
calculations for CAN-FD.
The next 12 patches are by me and several checkpatch warnings in the
af_can, raw and bcm components.
Thomas Gleixner provides a patch for the bcm, which switches the timer
to HRTIMER_MODE_SOFT and removes the hrtimer_tasklet.
Then 6 more patches by me for the gw component, which fix checkpatch
warnings, followed by 2 patches by Oliver Hartkopp to add CAN-FD
support.
The vcan driver gets 3 patches by me, fixing checkpatch warnings.
And finally a patch by Andre Hartmann to fix typos in CAN's netlink
header.
====================
|
|
The ctx->sk_write_space pointer is only set when TLS tx mode is enabled.
When running without TX mode its a null pointer but we still set the
sk sk_write_space pointer on close().
Fix the close path to only overwrite sk->sk_write_space when the current
pointer is to the tls_write_space function indicating the tls module should
clean it up properly as well.
Reported-by: Hillf Danton <hdanton@sina.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Fixes: 57c722e932cfb ("net/tls: swap sk_write_space on close")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If oct->fn_list.enable_io_queues() fails, no cleanup is executed, leading
to memory/resource leaks. To fix this issue, invoke
octeon_delete_instr_queue() before returning from the function.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull xfs fixes from Darrick Wong:
- Fix crashes when the attr fork isn't present due to errors but inode
inactivation tries to zap the attr data anyway.
- Convert more directory corruption debugging asserts to actual
EFSCORRUPTED returns instead of blowing up later on.
- Don't fail writeback just because we ran out of memory allocating
metadata log data.
* tag 'xfs-5.3-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: don't crash on null attr fork xfs_bmapi_read
xfs: remove more ondisk directory corruption asserts
fs: xfs: xfs_log: Don't use KM_MAYFAIL at xfs_log_reserve().
|
|
__page_pool_get_cached() will return NULL when the ring is
empty, even if there are pages present in the lookaside cache.
It is also possible to refill the cache, and then return a
NULL page.
Restructure the logic so eliminate both cases.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull iomap fixlet from Darrick Wong:
"A single update to the MAINTAINERS entry for iomap now that we've
removed fs/iomap.c"
* tag 'iomap-5.3-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
MAINTAINERS: iomap: Remove fs/iomap.c record
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-08-15
This series introduces two fixes to mlx5 driver.
1) Eran fixes a compatibility issue with ethtool flash.
2) Maxim fixes a race in XSK wakeup flow.
Please pull and let me know if there is any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Gerd Rausch says:
====================
net/rds: Fixes from internal Oracle repo
This is the first set of (mostly old) patches from our internal repository
in an effort to synchronize what Oracle had been using internally
with what is shipped with the Linux kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Original commit from 2011 updated to include a change by
Yuval Shaia <yuval.shaia@oracle.com>
that adds a new statistic counter "send_stuck_rm"
to capture the messages looping exessively
in the send path.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a previous commit, fields were added to "struct rds_statistics"
but array "rds_stat_names" was not updated accordingly.
Please note the inconsistent naming of the string representations
that is done in the name of compatibility
with the Oracle internal code-base.
s_recv_bytes_added_to_socket -> "recv_bytes_added_to_sock"
s_recv_bytes_removed_from_socket -> "recv_bytes_freed_fromsock"
Fixes: 192a798f5299 ("RDS: add stat for socket recv memory usage")
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Bang Nguyen <bang.nguyen@oracle.com>
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Signed-off-by: Somasundaram Krishnasamy <somasundaram.krishnasamy@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will kick the RDS worker thread if we have been looping
too long.
Original commit from 2012 updated to include a change by
Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
that triggers "must_wake" if "rds_ib_recv_refill_one" fails.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
netdevsim: implement support for devlink region and snapshots
Implement devlink region support for netdevsim and test it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test netdevsim devlink region implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
