| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add at24 EEPROM chip support.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add at24 EEPROM chip support.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[tony@atomide.com: updated to remove missing i2c1_pins]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove ADS7846 touchscreen pdata quirk for CM-T3x CoMs
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add ADS7846 touchscreen support.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix comment style
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add node for RTC.
Note that on dra7xx are no separate interrupts for alram
and timer unlike for SoCs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[nm@ti.com: update with rtc crossbar number]
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This adds support for the N900's battery to the
Nokia N900 DTS file.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add si4713 node to the N900 device tree file.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The HDMI node does not have a power supply attached. As a result its
power regulator, VDAC, shuts off on boot and screen loses signal.
This attaches VDAC (vdda_hdmi_dac) to HDMI's vdda-supply.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This adds the NovaTech OrionLXm which is based on the AM335x SoC
http://www.novatechweb.com/substation-automation/orionlxm/
RAM: 512MiB
Flash: 4GB eMMC
Ethernet PHYs: 2x Micrel KSZ8041FTLI
USB ports are used internally by the expansion cards.
Internal micro SD slot is available.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add serial port aliases for consoles > 6.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
BeagleBoard-X15 is the next generation Open Source Hardware
BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHz A15
processor. The platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x1080@60), separate LCD
port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G
Ethernet.
For more information, refer to:
BeagleBoard-X15 Wiki:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
AM5728 is part of the Sitara product family whose additional details
will be available: http://www.ti.com/lsds/ti/arm/overview.page
Technical Reference Manual for AM5728 is public domain at:
http://www.ti.com/lit/spruhz6
Just add basic support for the moment, the following updates are needed:
i) Ethernet - depends on SoC dts fixes
ii) USB Client (USB2) - depends on GPIO extcon
ii) HDMI - additional driver fixes pending
iii) Audio - additional driver fixes pending
NOTE:
AM5728 Data Manual (SPRS915L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions". This implies
that all unused voltage rails for AM5728 can never be switched off even
if the hardware blocks inside that voltage domain is unused. Switching
off these unused rails may result in stability issues on other domains
and increased leakage and power-on-hour impacts.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add btwilink device for IGEPv2 Rev. F and IGEP COM MODULE Rev. G.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can't suppose that the i2c2 pins are configured as I2C bus, these pins are
connected to expansion connectors.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add support for the new hardware revision of the IGEPv2. Basically, the new
revision F replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use the omap3-igep0020-common.dtsi file and remove repeated parts leaving
the nodes that are not common between IGEPv2 hardware revisions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add support for the new hardware revision of the IGEP COM MODULE. Basically,
the new revision G replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use the omap3-igep0030-common.dtsi file and remove repeated parts leaving
the nodes that are not common between IGEP COM MODULE hardware revisions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
New IGEP boards revisions will use another Wifi module, so this patch moves
the DT nodes outside the common omap3-igep.dtsi file to specific DT for every
board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We'll introduce new hardware revisions soon. This patch is only to
indicate which board revision supports this device tree file in order
to avoid confusions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We'll introduce new hardware revisions soon. This patch is only to
indicate which board revision supports this device tree file in order
to avoid confusions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
At this moment all supported boards use same NAND chip, so has more sense
move the GPMC and NAND configuration to the omap3-igep.dtsi common place.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
UART2 is used to connect the processor with the bluetooth chip, these pins
are not common between IGEPv2 boards and IGEP COM MODULE boards. This patch
muxes the correct pins for every board and removes UART2 configuration from
common omap3-igep.dtsi file.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
by adding labels to DWC3 nodes, it's far easier
for boards to reference them.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated for otg 4 move to dra74x.dtsi]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Adding CPSW phy-id, CPSW and MDIO pinmux configuration for active and
sleep states and enable them in board evm dts file.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
DRA7 Data Manual (SPRS857L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions".
This implies that all unused voltage rails for Vayu can never be
switched off even if the hardware blocks inside that voltage domain is
unused. Switching off these unused rails may result in stability issues
on other domains and increased leakage and power-on-hour impacts.
J6eco-evm dts file already considers this, however j6evm-dts file needs
to be fixed to consider this constraint of the SoC.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add MMC1 and 2 nodes. MMC1 is SDcard and MMC2 is eMMC.
NOTE on MMC1 card detect: Ideally, we should be using in-built SDCD
support, but we dont have it yet. So, use the fact that control module
of DRA7 is setup such that no matter what mode one configures it, GPIO
option is always hardwired in - use GPIO mode for SDcard detection.
[peter.ujfalusi@ti.com]
The power line feeding the SD card is also used by other devices on the EVM.
Use generic name instead of mmc2_3v3 so when other devices want to use the
same regulator it will look a bit better.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With Commit adff5962fdd2 ("Input: introduce palmas-pwrbutton"), we can
now support tps power button as a event source - This is SW7 (PB/WAKE)
on the J6-evm.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Even thought sys_nirq1 is hardwired on the SoC for the pin, it is
better to configure the pin to the required mux configuration.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The ldo4_reg regulator provides power to the USB1 and USB2
High Speed PHYs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add USB data and pinctrl for USB.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The 4th USB controller instance present only on the DRA74x family of
devices so move it there.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
DRA72-evm has a 256MB 16-bit wide NAND chip. Add
pinmux and NAND node.
The NAND chips 'Chip select' and 'Write protect' can be
controlled using DIP Switch SW5. To use NAND,
the switch must be configured like so:
SW5.1 (NAND_SELn) = ON (LOW)
SW5.9 (GPMC_WPN) = OFF (HIGH)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Adding CPSW phy-id, CPSW and MDIO pinmux configuration for active and
sleep states and enable them in board evm dts file.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add CPSW and MDIO related device tree data for DRA7XX and made as status
disabled. Phy-id, pinmux for active and sleep state needs to be added in
board dts files and enable the CPSW device.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use omap specific pinctrl defines (OMAP3_CORE1_IOPAD) to configure
the padconf register offset.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add DSS related pinmux and display data nodes required to support
DVI video out on SBC-T3530, SBC-T3730 and SBC-T3517.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Cc: devicetree@vger.kernel.org
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Cc: devicetree@vger.kernel.org
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The '#mbox-cells' property is added to all the OMAP mailbox
nodes. This property is mandatory with the new mailbox framework.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the interrupts property to all the 13 mailbox nodes in
DRA7xx. The interrupts property information added is inline
with the expected values with the DRA7xx crossbar driver,
and is common to both DRA74x and DRA72x SoCs.
Do note that the mailbox 1 is only capable of generating out
3 interrupts, while all the remaining mailboxes have 4
interrupts each.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Looks like we have some GPMC NAND timings missing device
width. This fixes "gpmc_cs_program_settings: invalid width 0!"
errors during boot.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With the GPMC warnings now enabled, I noticed the LAN9220 timings
can overflow the GPMC registers with 200MHz L3 speed. Earlier we
were just skipping the bad timings and would continue with the
bootloader timings. Now we no longer allow to continue with bad
timings as we have the timings in the .dts files.
We could start using the GPMC clock divider, but let's instead
use the u-boot timings that are known to be working and a bit
faster. These are basically the u-boot NET_GPMC_CONFIG[1-6]
defines deciphered. Except that we don't set gpmc,burst-length
as that's only partially configured and does not seem to work
if fully enabled.
[tony@atomide.com: updated to remove gpmc,burst-length]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The four port serial port on the zoom debug board uses a TL16CP754C
with a single interrupt and GPMC chip select. The serial ports each
use a 8 bytes for IO registers, and are 256 bytes apart on the GPMC
line.
Let's add timings for all four ports so we can remove the GPMC
workarounds for using bootloader timings.
Not caused by this patch, but looks like u-boot only properly
initializes the fifo on the first serial port. Currently the other
ports produce garbage at least with my version of u-boot. I suspect
that TL16CP754C needs non-standard initialization added to 8250
driver to properly fix this issue.
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Let's use the bootloader values except for the partially configured
wait-pin that does not seem to work.
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The GPMC binding is obviously very confusing as the values
are all over the place. People seem to confuse the GPMC partition
size for the chip select, and the device IO size within the GPMC
partition easily.
The ranges entry contains the GPMC partition size. And the
reg entry contains the size of the IO registers of the
device connected to the GPMC.
Let's fix the issue according to the following table:
Device GPMC partition size Device IO size
connected in the ranges entry in the reg entry
NAND 0x01000000 (16MB) 4
16550 0x01000000 (16MB) 8
smc91x 0x01000000 (16MB) 0xf
smc911x 0x01000000 (16MB) 0xff
OneNAND 0x01000000 (16MB) 0x20000 (128KB)
16MB NOR 0x01000000 (16MB) 0x01000000 (16MB)
32MB NOR 0x02000000 (32MB) 0x02000000 (32MB)
64MB NOR 0x04000000 (64MB) 0x04000000 (64MB)
128MB NOR 0x08000000 (128MB) 0x08000000 (128MB)
256MB NOR 0x10000000 (256MB) 0x10000000 (256MB)
Let's also add comments to the fixed entries while at it.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Apparently some versions of nolo don't mux the all the necessary GPMC
pins for the smc91x probe to work properly. Let's fix this issue
by adding mux support for GPMC to the kernel.
Note that GPMC clk needs input enabled for OnenNAND to work.
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another small batch of fixes.
Most of these make zynq, socfpga and sunxi platforms work a bit
better:
- due to new requirements for regulators, DWMMC on socfpga broke past
v3.17
- SMP spinup fix for socfpga
- a few DT fixes for zynq
- another option (FIXED_REGULATOR) for sunxi is needed that used to
be selected by other options but no longer is.
- a couple of small DT fixes for at91
- ...and a couple for i.MX"
* tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
ARM: multi_v7_defconfig: enable CONFIG_MMC_DW_ROCKCHIP
ARM: sunxi_defconfig: enable CONFIG_REGULATOR_FIXED_VOLTAGE
ARM: dts: socfpga: Add a 3.3V fixed regulator node
ARM: dts: socfpga: Fix SD card detect
ARM: dts: socfpga: rename gpio nodes
ARM: at91/dt: sam9263: fix PLLB frequencies
power: reset: at91-reset: fix power down register
MAINTAINERS: add atmel ssc driver maintainer entry
arm: socfpga: fix fetching cpu1start_addr for SMP
ARM: zynq: DT: trivial: Fix mc node
ARM: zynq: DT: Add cadence watchdog node
ARM: zynq: DT: Add missing reference for memory-controller
ARM: zynq: DT: Add missing reference for ADC
ARM: zynq: DT: Add missing address for L2 pl310
ARM: zynq: DT: Remove 222 MHz OPP
ARM: zynq: DT: Fix GEM register area size
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"overlayfs merge + leak fix for d_splice_alias() failure exits"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
overlayfs: embed middle into overlay_readdir_data
overlayfs: embed root into overlay_readdir_data
overlayfs: make ovl_cache_entry->name an array instead of pointer
overlayfs: don't hold ->i_mutex over opening the real directory
fix inode leaks on d_splice_alias() failure exits
fs: limit filesystem stacking depth
overlay: overlay filesystem documentation
overlayfs: implement show_options
overlayfs: add statfs support
overlay filesystem
shmem: support RENAME_WHITEOUT
ext4: support RENAME_WHITEOUT
vfs: add RENAME_WHITEOUT
vfs: add whiteout support
vfs: export check_sticky()
vfs: introduce clone_private_mount()
vfs: export __inode_permission() to modules
vfs: export do_splice_direct() to modules
vfs: add i_op->dentry_open()
|
