summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2013-06-03ath9k: Simplify ANI initializationSujith Manoharan6-27/+10
The check "enable_ani" is not required since it is always set to true and the logic for disabling/enabling ANI via debugfs is done at a higher layer. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03ath9k: Remove unused structure ath_dbg_bb_mac_sampSujith Manoharan1-39/+0
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03ath9k: Enable WoW only for AR9462Sujith Manoharan7-207/+35
The only card with which WoW has been tested and verified is AR9462. Do not enable it for all cards since WoW is really quirky and needs to be tested properly with each chip. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03ath9k: Return early for invalid ratesSujith Manoharan1-2/+2
Process and update the internal RSSI average, which is used by ANI, after verifying that the received frame has valid rate information. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03net, ipw2x00: remove redundant D0 power state setYijing Wang1-2/+0
Pci_enable_device() will set device power state to D0, so it's no need to do it again in ipw2100_pci_init_one(). Signed-off-by: Yijing Wang <wangyijing@huawei.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03ath9k: advertise support for active monitor interfacesFelix Fietkau1-0/+2
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03Merge branch 'for-john' of ↵John W. Linville10-16/+75
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
2013-06-03cw1200: rename the cw1200 platform definition headerSolomon Peachy3-2/+2
My previous patch just moved the file, but it also needed to be renamed to conform to proper conventions. Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03cw1200: Rework SDIO platform support to prevent build problems.Solomon Peachy5-122/+66
Based on discussions with And Bergmann, this patch changes the SDIO platform code to default to supporting the Sagrad devices, allowing for it to be overridden in board setup code. This renders the cw1200_sagrad module suplerflous, so it is now removed. It also moves the documentation that was in the cw1200_sagrad source to the platform header. Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03cw1200: Replace use of 'struct resource' with 'int' for GPIO fields.Solomon Peachy4-97/+47
The only advantage of 'struct resource' is that it lets us assign names as part of the platform data. Unfortunately since we are using platform data, we are already limited to a single instance of each driver, rendering this moot. So, replace the struct resources with ints, resulting in cleaner code. This was based on a suggestion from Arnd Bergmann. Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03cw1200: Reference correct 'powerup' GPIO signal.Solomon Peachy2-2/+2
Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03cw1200: move platform_data header to correct location.Solomon Peachy4-3/+3
(As suggested by Arnd Bergmann) Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03cw1200: Rename 'sbus' to 'hwbus'Solomon Peachy10-123/+119
This avoids problems when building on SPARC targets due to the driver calling the bus abstraction layer 'sbus'. Not that any SBUS-sporting SPARC targets are likely to have an SDIO controller, but this is the correct thing to do. See http://kisskb.ellerman.id.au/kisskb/buildresult/8846508/ Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03mac80211: fix sdata locking around __ieee80211_request_smpsJohannes Berg1-0/+2
My cfg80211/mac80211 locking unification broke the sdata locking in ieee80211_set_power_mgmt, it needs to acquire the lock for __ieee80211_request_smps(). Add the locking. Reported-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-31Revert "mac80211_hwsim: remove P2P_DEVICE support"Johannes Berg1-1/+3
This reverts commit e3ee68b7b049c5bbfcb78a179c00c373a38ed58c. This wasn't intended to be included here, my mistake. I accidentally merged a mac80211 fixes tree here that had this change, when it wasn't even intended to be there. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-31Revert "iwlwifi: mvm: remove P2P_DEVICE support"Johannes Berg1-1/+13
This reverts commit eebfc9394ee31b3ef162692c0cd483c1318a4395. This wasn't intended to be included here, my mistake. I accidentally merged a mac80211 fixes tree here that had this change, when it wasn't even intended to be there. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-30cw1200: remove unused including <linux/version.h>Wei Yongjun3-3/+0
Remove including <linux/version.h> that don't need it. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-30cw1200: use module_spi_driver to simplify the codeWei Yongjun1-14/+1
module_spi_driver() makes the code simpler by eliminating boilerplate code. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-30cw1200: convert to use simple_open()Wei Yongjun1-7/+1
This removes an open coded simple_open() function and replaces file operations references to the function with simple_open() instead. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-30cw1200: remove duplicated include from wsm.cWei Yongjun1-1/+0
Remove duplicated include. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-30cw1200: Fix compile with CONFIG_PM=nSolomon Peachy5-4/+27
Intel's 0-day kernel build tester caught this build failure. This patch properly wraps everything that depends on CONFIG_PM. Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-30ath9k: check for Rx-STBC flag and pass it to ieee80211Oleksij Rempel3-3/+15
This patch make use of STBC flag in DMA RX descriptor. Only devices after ar9280 can provide this information. If card support it we will set HAVE_STBC flag, to show clint programm thet STBC is supported but not received. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-30ath9k: remove useless flag conversation.Oleksij Rempel4-10/+12
some flags used only outside of ath9k - In this case we can use "enum mac80211_rx_flags" and pass it upstream without extra conversation. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-29cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsetsSolomon Peachy34-0/+15040
Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-29mwifiex: dump small buffers with help of %*phAndy Shevchenko1-3/+2
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-29net: wireless: p54spi: Fix commenting styleSachin Kamat1-8/+7
Make the commenting style consistent with networking block comment style as suggested by checkpatch. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-29net: wireless: p54spi: Use module_spi_driver macroSachin Kamat1-21/+1
module_spi_driver() eliminates some boiler plate and makes code simpler. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-29ath9k_hw: fix PA predistortion miscalibrationFelix Fietkau1-8/+11
If any bins from the training data are skipped (i != max_index), the calculated compensation curve gets distorted, and the signal will be wildly overamplified. This may be the cause of the reported hardware damage that was caused by PA predistortion (because of which PAPRD was disabled by default). When calculating the x_est, Y, theta values, the use of max_index and i was reversed. i points to the bin index whereas max_index refers to the index of the calculated arrays. Note that PA predistortion is still disabled, it will be re-enabled after it has been properly validated. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-29wil6210: Don't use wdev->sme_stateVladimir Kondratiev4-13/+13
sme_state is private wdev's variable. Track connection state internally Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-29wil6210: channel off by 1Vladimir Kondratiev1-1/+1
WMI commands wants channel index, that is channel - 1 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-29Merge branch 'for-john' of ↵John W. Linville47-1388/+1007
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
2013-05-29Merge branch 'for-john' of ↵John W. Linville70-546/+2907
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
2013-05-29mac80211: always send multicast on CAB queueJohannes Berg1-2/+3
If the driver advertised support for a CAB queue, then we should put all multicast frames there, otherwise sending them can be racy with clients going to sleep while we TX a frame. To avoid this, always TX multicast frames on the multicast queue. It seems like even drivers not using the queue framework might want to do this which would mean also moving the IEEE80211_TX_CTL_SEND_AFTER_DTIM flag assignment, but it also seems that drivers behave differently here so that just moving it wouldn't be a good idea. It'd be better to modify those drivers to use the queue framework. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-29cfg80211: remove cleanup_work kernel-docJohannes Berg1-1/+0
I evidently forgot this when removing the work itself. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-29mac80211: support active monitor interfacesFelix Fietkau4-11/+38
Support them only if the driver advertises support for them via IEEE80211_HW_SUPPORTS_ACTIVE_MONITOR. Unlike normal monitor interfaces, they are added to the driver, along with their MAC address. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-29cfg80211: support an active monitor interface flagFelix Fietkau3-0/+16
An active monitor interface is one that is used for communication (via injection). It is expected to ACK incoming unicast packets. This is useful for running various 802.11 testing utilities that associate to an AP via injection and manage the state in user space. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-29iwlwifi: mvm: add debugfs for powersaveAlexander Bondar3-0/+468
Add debugfs files to control powersave parameters for testing. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-29iwlwifi: mvm: Add support for connection monitor offloadHila Gonen5-1/+54
The firmware supports periodic keep alive and beacon monitoring, so advertise connection monitor offload capability by setting IEEE80211_HW_CONNECTION_MONITOR flag. Implement missed beacons notification handler. Call ieee80211_beacon_loss in case of missed beacons, so AP probing by mac80211 can be triggered. Signed-off-by: Hila Gonen <hila.gonen@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-29iwlwifi: take valid ant for HT caps from TLVEmmanuel Grumbach5-16/+22
I forgot to take them from TLV and took them from the NVM instead. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-29iwlwifi: mvm: Change number of DTIMs to skip semanticsAlexander Bondar2-5/+7
If skip over DTIMs is enabled the driver can specify number of DTIMs to skip. This parameter in host-device API implies number of DTIM periods to skip. For example, to skip one DTIM means sleep over two DTIM periods. Change semantics accordingly. Change this parameter's default value. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-29iwlwifi: mvm: add thermal throttling and CT killEytan Lifshitz17-18/+974
In order to avoid NIC destruction due to high temperature, CT kill will power down the NIC. To avoid this, thermal throttling will decrease throughput to prevent the NIC from reaching the temperature at which CT kill is performed. Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-27cfg80211: make WoWLAN configuration available to driversJohannes Berg5-38/+52
Make the current WoWLAN configuration available to drivers at runtime. This isn't really useful for the normal WoWLAN behaviour and accessing it can also be racy, but drivers may use it for testing the WoWLAN device behaviour while the host stays up & running to observe the device. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-27iwlwifi: mvm: use proper scan type for P2PEmmanuel Grumbach1-6/+0
It was set to be FORCED because of a firmware bug which has been fixed. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-27Merge remote-tracking branch 'iwlwifi-fixes/master' into HEADJohannes Berg21-140/+237
Conflicts: drivers/net/wireless/iwlwifi/mvm/ops.c
2013-05-27iwlwifi: mvm: Add beacon abort enablementAlexander Bondar3-46/+86
Beacon abort is used by device to increase idle dwell time when system is idle. This algorithm is on top of beacon filtering feature. Enable beacon abort only if power management is enabled. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-27iwlwifi: dvm: constify configuration structsJohannes Berg2-19/+19
The pointer that gets used is already const, so the structs can obviously be const as well. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-27iwlwifi: move some configuration parameters into DVMJohannes Berg20-187/+217
There are a number of parameters that aren't really hardware specific but rather define how the DVM firmware is used. Move these into the DVM configuration. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-27iwlwifi: dvm: rename iwl_lib_ops to iwl_dvm_cfgJohannes Berg4-23/+23
The next patches will move some more configuration data that isn't needed by mvm into this struct, so rename it now since it won't just be ops. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-27iwlwifi: move D3_CFG_COMPLETE handling into DVMJohannes Berg2-7/+8
The MVM firmware doesn't communicate this way, it instead assumes D3 configuration is complete after a specific host command (which must be last) has been sent. Handling this bit thus belongs into the firmware API code, i.e. DVM. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-05-27iwlwifi: dvm: fix zero LQ CMD sending avoidanceEmmanuel Grumbach1-1/+1
In 63b77bf489881747c5118476918cc8c29378ee63 iwlwifi: dvm: don't send zeroed LQ cmd I tried to avoid to send zeroed LQ cmd, but I made a (very) stupid mistake in the memcmp. Since this patch has been ported to stable, the fix should go to stable too. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58341 Cc: stable@vger.kernel.org Reported-by: Hinnerk van Bruinehsen <h.v.bruinehsen@fu-berlin.de> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-27 01:01:00 +0300