summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2023-03-24arm64: dts: qcom: ipq8074-hk01: enable QMP device, not the PHY nodeDmitry Baryshkov1-2/+2
Correct PCIe PHY enablement to refer the QMP device nodes rather than PHY device nodes. QMP nodes have 'status = "disabled"' property in the ipq8074.dtsi, while PHY nodes do not correspond to the actual device and do not have the status property. Fixes: e8a7fdc505bb ("arm64: dts: ipq8074: qcom: Re-arrange dts nodes based on address") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230324021651.1799969-1-dmitry.baryshkov@linaro.org
2023-03-24arm64: dts: qcom: sc8280xp-x13s: enable alternate touchpadJohan Hovold1-9/+1
Enable both touchpad nodes in the devictree and let the HID driver determine which one is actually populated (by attempting to read from each i2c address). Ideally this would not be needed and the boot firmware should instead enable only the node for the populated touchpad, but this is unlikely to ever be realised for the X13s. Note that the pin configuration must currently be moved to the parent i2c-bus node even though only one of these nodes will ever be successfully probed on a specific device (e.g. to allow them to be probed in parallel). Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230324094744.20448-1-johan+linaro@kernel.org
2023-03-23arm64: dts: qcom: qrb5165-rb5: Use proper WSA881x shutdown GPIO polarityKrzysztof Kozlowski1-2/+2
The WSA881x shutdown GPIO is active low (SD_N), but Linux driver assumed DTS always comes with active high. Since Linux drivers were updated to handle proper flag, correct the DTS. The change is not backwards compatible with older Linux kernel. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230322193051.826167-5-krzysztof.kozlowski@linaro.org
2023-03-23arm64: dts: qcom: sm8250-mtp: Use proper WSA881x shutdown GPIO polarityKrzysztof Kozlowski1-2/+2
The WSA881x shutdown GPIO is active low (SD_N), but Linux driver assumed DTS always comes with active high. Since Linux drivers were updated to handle proper flag, correct the DTS. The change is not backwards compatible with older Linux kernel. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230322193051.826167-4-krzysztof.kozlowski@linaro.org
2023-03-23arm64: dts: qcom: sdm850-samsung-w737: Use proper WSA881x shutdown GPIO polarityKrzysztof Kozlowski1-2/+2
The WSA881x shutdown GPIO is active low (SD_N), but Linux driver assumed DTS always comes with active high. Since Linux drivers were updated to handle proper flag, correct the DTS. The change is not backwards compatible with older Linux kernel. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230322193051.826167-3-krzysztof.kozlowski@linaro.org
2023-03-23arm64: dts: qcom: sdm850-lenovo-yoga-c630: Use proper WSA881x shutdown GPIO ↵Krzysztof Kozlowski1-2/+2
polarity The WSA881x shutdown GPIO is active low (SD_N), but Linux driver assumed DTS always comes with active high. Since Linux drivers were updated to handle proper flag, correct the DTS. The change is not backwards compatible with older Linux kernel. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230322193051.826167-2-krzysztof.kozlowski@linaro.org
2023-03-23arm64: dts: qcom: sc8280xp-pmics: fix sdam 'reg' propertyJohan Hovold1-1/+1
The SPMI PMIC register region width is fixed and should not be encoded in the devicetree. Fixes: d6dbbda37ab5 ("arm64: dts: qcom: sc8280xp-pmics: add pmk8280 sdam nvram") Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230320135710.1989-3-johan+linaro@kernel.org
2023-03-23arm64: dts: qcom: sm8450: add dp controllerNeil Armstrong1-0/+79
Add the Display Port controller subnode to the MDSS node. Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230206-topic-sm8450-upstream-dp-controller-v6-5-d78313cbc41d@linaro.org
2023-03-23arm64: dts: qcom: sm8450: switch to usb3/dp combo phyNeil Armstrong1-27/+15
The QMP PHY is a USB3/DP combo phy, switch to the newly documented bindings and register the clocks to the GCC and DISPCC controllers. Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230206-topic-sm8450-upstream-dp-controller-v6-4-d78313cbc41d@linaro.org
2023-03-23arm64: dts: qcom: sm8350: add dp controllerNeil Armstrong1-0/+79
Add the Display Port controller subnode to the MDSS node. Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #SM8350-HDK Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230206-topic-sm8450-upstream-dp-controller-v6-3-d78313cbc41d@linaro.org
2023-03-23arm64: dts: qcom: sm8350: switch to combo usb3/dp phyNeil Armstrong1-27/+15
The first QMP PHY is an USB3/DP combo phy, switch to the newly documented bindings and register the clocks to the GCC and DISPCC controllers. Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #SM8350-HDK Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230206-topic-sm8450-upstream-dp-controller-v6-2-d78313cbc41d@linaro.org
2023-03-23arm64: dts: qcom: sc7280: align RPMh regulator nodes with bindingsKrzysztof Kozlowski5-7/+7
Device node names should be generic and bindings expect certain pattern for RPMh regulator nodes. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230217155838.848403-3-krzysztof.kozlowski@linaro.org
2023-03-23arm64: dts: qcom: sc7280-herobrine-audio-rt5682: add missing suppliesKrzysztof Kozlowski2-0/+4
Bindings expect DBVDD-supply and LDO1-IN-supply: sc7280-herobrine-evoker-lte.dtb: codec@1a: 'DBVDD-supply' is a required property sc7280-herobrine-evoker-lte.dtb: codec@1a: 'LDO1-IN-supply' is a required property In sc7180-trogdor.dtsi they come from the same regulator, so let's assume intention was the same here. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230217155838.848403-2-krzysztof.kozlowski@linaro.org
2023-03-23arm64: dts: qcom: sc7180-trogdor-pazquel360: drop incorrect RT5682S VBAT-supplyKrzysztof Kozlowski1-0/+1
It seems that the RT5682S codec does not use VBAT-supply: sc7180-trogdor-pazquel360-lte.dtb: codec@1a: Unevaluated properties are not allowed ('VBAT-supply' was unexpected) Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230217155838.848403-1-krzysztof.kozlowski@linaro.org
2023-03-23arm64: dts: qcom: ipq5332: enable the CPUFreq supportKathiravan T1-0/+37
Add the APCS, A53 PLL, cpu-opp-table nodes to bump the CPU frequency above 800MHz. Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230217083308.12017-6-quic_kathirav@quicinc.com
2023-03-22arm64: dts: qcom: sc8280xp-x13s: add wifi calibration variantJohan Hovold1-0/+17
Describe the bus topology for PCIe domain 6 and add the ath11k calibration variant so that the board file (calibration data) can be loaded. Link: https://bugzilla.kernel.org/show_bug.cgi?id=216246 Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Tested-by: Steev Klimaszewski <steev@kali.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230321094011.9759-3-johan+linaro@kernel.org
2023-03-22arm64: dts: qcom: sc8280xp-x13s: add hid 1.8V suppliesJohan Hovold1-0/+4
All the input devices use s10b as 1.8V supply. Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230322113318.17908-7-johan+linaro@kernel.org
2023-03-22arm64: dts: qcom: sc8280xp-x13s: add pmic regulator suppliesJohan Hovold1-0/+22
The s11b, s12b, s1c and bob supplies are used by several pmic regulators. Add the missing description to the devicetree. Note that there are still some consumers that are not (fully) described in the devicetree so the supplies must remain marked as always-on for now. Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230322113318.17908-6-johan+linaro@kernel.org
2023-03-22arm64: dts: qcom: sc8280xp-x13s: mark bob regulator as always-onJohan Hovold1-0/+1
The bob supply is used by several pmic regulators and components which are not (yet fully) described in the devicetree. Mark the regulator as always-on for now. Fixes: f29077d86652 ("arm64: dts: qcom: sc8280xp-x13s: Add soundcard support") Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230322113318.17908-5-johan+linaro@kernel.org
2023-03-22arm64: dts: qcom: sc8280xp-x13s: mark s12b regulator as always-onJohan Hovold1-0/+1
The s12b supply is used by several pmic regulators as well as the wlan/bluetooth radio which are not yet fully described in the devicetree. Mark the regulator as always-on for now. Fixes: f29077d86652 ("arm64: dts: qcom: sc8280xp-x13s: Add soundcard support") Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230322113318.17908-4-johan+linaro@kernel.org
2023-03-22arm64: dts: qcom: sc8280xp-x13s: mark s10b regulator as always-onJohan Hovold1-0/+1
The s10b supply is used by several components that are not (yet) described in devicetree (e.g. ram, charger, ec) and must not be disabled. Mark the regulator as always-on. Fixes: f29077d86652 ("arm64: dts: qcom: sc8280xp-x13s: Add soundcard support") Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230322113318.17908-3-johan+linaro@kernel.org
2023-03-22arm64: dts: qcom: sc8280xp-x13s: mark s11b regulator as always-onJohan Hovold1-0/+1
The s11b supply is used by the wlan module (as well as some of the pmics) which are not yet fully described in the devicetree. Mark the regulator as always-on for now. Fixes: 123b30a75623 ("arm64: dts: qcom: sc8280xp-x13s: enable WiFi controller") Cc: stable@vger.kernel.org # 6.2 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230322113318.17908-2-johan+linaro@kernel.org
2023-03-22arm64: dts: qcom: sm8450-hdk: align WCD9385 reset pin with downstream configKrzysztof Kozlowski1-1/+3
Downstream DTS uses 16 mA drive strength for the WCD9385 audio codec RESET_N reset pin. It also pulls the pin down in shutdown mode, thus it is more like a shutdown pin, not a reset. Use the same settings here for HDK8450 and keep the WCD9385 by default in powered off (so pin as low). Align the name of pin configuration node with other pins in the DTS. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230308183317.559253-2-krzysztof.kozlowski@linaro.org
2023-03-22arm64: dts: qcom: sm8450-hdk: use precise WCD9385 compatibleKrzysztof Kozlowski1-1/+1
The HDK8450 uses WCD9385 audio codec, so use precise compatible, even though WCD9380 and WCD9385 are both compatible. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230308183317.559253-1-krzysztof.kozlowski@linaro.org
2023-03-22arm64: dts: qcom: sm8450-hdk: use recommended drive strength for speaker SD_NKrzysztof Kozlowski1-2/+2
Downstream DTS (and sc8280xp-lenovo-thinkpad-x13s with the same speakers) uses 16 mA drive strength for the WSA8835 speaker SD_N reset/shutdown pin. Use the same for HDK8450, as it is seem the recommended value. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230308142712.277659-1-krzysztof.kozlowski@linaro.org
2023-03-22arm64: dts: qcom: sm8150: Add SoC-specific compatible to cpufreq_hwKonrad Dybcio1-1/+1
Add a SoC-specific compatbile to cpufreq_hw for compliancy with bindings. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230308-topic-cpufreq_bindings-v1-8-3368473ec52d@linaro.org
2023-03-22arm64: dts: qcom: sm6350: Add SoC-specific compatible to cpufreq_hwKonrad Dybcio1-1/+1
Add a SoC-specific compatbile to cpufreq_hw for compliancy with bindings. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Luca Weiss <luca.weiss@fairphone.com> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230308-topic-cpufreq_bindings-v1-7-3368473ec52d@linaro.org
2023-03-22arm64: dts: qcom: sm6115: Add SoC-specific compatible to cpufreq_hwKonrad Dybcio1-1/+1
Add a SoC-specific compatbile to cpufreq_hw for compliancy with bindings. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230308-topic-cpufreq_bindings-v1-6-3368473ec52d@linaro.org
2023-03-22arm64: dts: qcom: sdm845: Add SoC-specific compatible to cpufreq_hwKonrad Dybcio1-1/+1
Add a SoC-specific compatbile to cpufreq_hw for compliancy with bindings. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230308-topic-cpufreq_bindings-v1-5-3368473ec52d@linaro.org
2023-03-22arm64: dts: qcom: sc7180: Add SoC-specific compatible to cpufreq_hwKonrad Dybcio1-1/+1
Add a SoC-specific compatbile to cpufreq_hw for compliancy with bindings. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230308-topic-cpufreq_bindings-v1-4-3368473ec52d@linaro.org
2023-03-22arm64: dts: qcom: sdm845-oneplus-common: add Hall sensorGergo Koteles1-0/+25
Enable the Hall effect sensor (flip cover) for OnePlus 6/6T. The GPIO is mapped to SW_LID events as in msm8916, msm8994, msm8998 devices. Signed-off-by: Gergo Koteles <soyer@irl.hu> Reviewed-by: Caleb Connolly <caleb@connolly.tech> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230306174147.185239-1-soyer@irl.hu
2023-03-22arm64: dts: qcom: drop redundant line breaksKrzysztof Kozlowski18-29/+0
Remove trailing, redundant line breaks. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230306081430.28491-2-krzysztof.kozlowski@linaro.org
2023-03-22arm64: dts: qcom: sdm845-db845c: drop empty node overrideKrzysztof Kozlowski1-4/+0
Drop empty override of pm8998_gpios. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230306081430.28491-1-krzysztof.kozlowski@linaro.org
2023-03-22arm64: dts: qcom: pm660: align thermal node names with bindingsKrzysztof Kozlowski2-2/+2
Bindings expect thermal node names to end with '-thermal', so fix pm660 and pm660l: sda660-inforce-ifc6560.dtb: thermal-zones: 'pm660', 'pm660l' do not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+' Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230305154308.241651-1-krzysztof.kozlowski@linaro.org
2023-03-22arm64: dts: qcom: sm8350-microsoft-surface: fix USB dual-role mode propertyKrzysztof Kozlowski1-0/+3
The "dr_mode" is a property of USB DWC3 node, not the Qualcomm wrapper one: sm8350-microsoft-surface-duo2.dtb: usb@a6f8800: 'dr_mode' does not match any of the regexes: '^usb@[0-9a-f]+$', 'pinctrl-[0-9]+' Fixes: c16160cfa565 ("arm64: dts: qcom: add minimal DTS for Microsoft Surface Duo 2") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230304130315.51595-2-krzysztof.kozlowski@linaro.org
2023-03-22arm64: dts: qcom: sm8250-xiaomi-elish: fix USB maximum speed propertyKrzysztof Kozlowski1-1/+1
Fix typo in USB DWC3 node maximum speed property. Fixes: a41b617530bf ("arm64: dts: qcom: sm8250: Add device tree for Xiaomi Mi Pad 5 Pro") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230304130315.51595-1-krzysztof.kozlowski@linaro.org
2023-03-22arm64: dts: qcom: sa8775p-ride: enable the BT UART portBartosz Golaszewski1-0/+33
Enable the high-speed UART port connected to the Bluetooth controller on the sa8775p-adp development board. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230309103752.173541-10-brgl@bgdev.pl
2023-03-22arm64: dts: qcom: sa8775p-ride: enable the GNSS UART portBartosz Golaszewski1-0/+33
Enable the high-speed UART port connected to the GNSS controller on the sa8775p-adp development board. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230309103752.173541-9-brgl@bgdev.pl
2023-03-22arm64: dts: qcom: sa8775p: add high-speed UART nodesBartosz Golaszewski1-0/+30
Add two UART nodes that are known to be used by existing development boards with this SoC. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230309103752.173541-8-brgl@bgdev.pl
2023-03-22arm64: dts: qcom: sa8775p-ride: enable the SPI nodeBartosz Golaszewski1-0/+14
Enable the SPI interface exposed on the sa8775p-ride development board. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230309103752.173541-7-brgl@bgdev.pl
2023-03-22arm64: dts: qcom: sa8775p: add the spi16 nodeBartosz Golaszewski1-0/+21
Add the SPI controller node for the interface exposed on the sa8775p-ride development board. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230309103752.173541-6-brgl@bgdev.pl
2023-03-22arm64: dts: qcom: sa8775p-ride: enable i2c18Bartosz Golaszewski1-0/+15
This enables the I2C interface on the sa8775p-ride development board. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230309103752.173541-5-brgl@bgdev.pl
2023-03-22arm64: dts: qcom: sa8775p: add the i2c18 nodeBartosz Golaszewski1-0/+22
Add a disabled node for the I2C interface that's exposed on the sa8775p-ride development board. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230309103752.173541-4-brgl@bgdev.pl
2023-03-22arm64: dts: qcom: sa8775p-ride: enable QUPv3 #2Bartosz Golaszewski1-0/+4
Enable the second instance of the QUPv3 engine on the sa8775p-ride board. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230309103752.173541-3-brgl@bgdev.pl
2023-03-22arm64: dts: qcom: sa8775p: add the QUPv3 #2 nodeBartosz Golaszewski1-0/+13
Add the second instance of the QUPv3 engine to the sa8775p.dtsi. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230309103752.173541-2-brgl@bgdev.pl
2023-03-22arm64: dts: qcom: pm8150l: add spmi-flash-led nodeDanila Tikhonov1-0/+6
Add a node describing the flash block found on pm8150l. Signed-off-by: Danila Tikhonov <danila@jiaxyga.com> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230321182319.24958-1-danila@jiaxyga.com
2023-03-22arm64: dts: qcom: sdm845: Fix the BAM DMA engine compatible stringBhupesh Sharma1-1/+1
As per documentation, Qualcomm SDM845 SoC supports BAM DMA engine v1.7.4, so use the correct compatible strings. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230321190118.3327360-2-bhupesh.sharma@linaro.org
2023-03-22arm64: dts: qcom: sm8550-mtp: add pmic glink nodeNeil Armstrong1-1/+44
Add the pmic glink node linked with the DWC3 USB controller switched to OTG mode and tagged with usb-role-switch. Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230130-topic-sm8450-upstream-pmic-glink-v5-11-552f3b721f9e@linaro.org
2023-03-22arm64: dts: qcom: sm8450-hdk: add pmic glink nodeNeil Armstrong1-1/+44
Add the pmic glink node linked with the DWC3 USB controller switched to OTG mode and tagged with usb-role-switch. Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230130-topic-sm8450-upstream-pmic-glink-v5-10-552f3b721f9e@linaro.org
2023-03-22arm64: dts: qcom: sm8350-hdk: add pmic glink nodeNeil Armstrong1-2/+44
Add the pmic glink node linked with the DWC3 USB controller switched to OTG mode and tagged with usb-role-switch. Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230130-topic-sm8450-upstream-pmic-glink-v5-9-552f3b721f9e@linaro.org
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-27 06:29:43 +0300