summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2018-11-30mt76x0: pci: enable VHT rates in IBSS modeLorenzo Bianconi2-3/+2
Enable VHT tx rates in ad-hoc mode for mt76x0e driver. Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: introduce mt76x02_config_mac_addr_list routineLorenzo Bianconi4-15/+27
Add mt76x02_config_mac_addr_list routine in order to set the mac address list supported by the driver. Initialize wiphy->addresses/n_addresses for mt76x0e driver Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: dfs: fix IBI_R11 configuration on non-radar channelsLorenzo Bianconi1-2/+6
Fix IBI_R11 configuration on non-radar channels for mt76x0e driver. This patch improve system stability under heavy load. Moreover use IBI_R11 name and remove magic numbers for 0x212c register Fixes: 0c3b3abc9251 ("mt76x0: pci: add DFS support") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x02: assure we update gain after scanStanislaw Gruszka3-3/+8
Assure that after we initialize dev->cal.low_gain to -1 this will cause update gain calibration. Otherwise this might or might not happen depending on value of second bit of low_gain and values read from registers in mt76x02_phy_adjust_vga_gain(). Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x02: run calibration after scanningStanislaw Gruszka4-1/+6
If we are associated and scanning is performed, sw_scan_complete callback is done after we get back to operating channel, so we do not perform queue cal work. Fix this queue cal work from sw_scan_complete(). On mt76x0 we have to restore gain in MT_BBP(AGC, 8) register after scanning, as it was multiple times modified by channel switch code. So queue cal work without any delay to set AGC gain value. Similar like in mt76x2 init AGC gain only when set operating channel and just check before queuing cal work in sw_scan_complete() if initialization was already done. Fixes: bbd10586f0df ("mt76x0: phy: do not run calibration during channel switch") Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: remove wait argument from mt76x02_mcu_set_radio_stateStanislaw Gruszka6-10/+7
Remove wait argument from mt76x02_mcu_set_radio_state and newer wait for response when sending CMD_POWER_SAVING_OP mcu command. Note this change behaviour for PCIe devices, but the change is in align with vendor driver. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: remove wait argument from mt76x02_mcu_function_selectStanislaw Gruszka6-12/+13
Remove wait argument from mt76x02_mcu_function_select and wait for response when function is not Q_SELECT, what is the same behaviour like in vendor driver. Note this change behaviour for PCIe devices for Q_SELECT function form wait to no-wait, and for mt76x0u BW_SETTING from no-wait to wait. But the change is in align with vendor driver. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: remove mcu_msg_allocStanislaw Gruszka7-44/+35
We almost always use patter like this: skb = mt76_mcu_msg_alloc(dev, &msg, sizeof(msg)); return mt76_mcu_send_msg(dev, skb, CMD_FUN_SET_OP, wait_resp); This is not needed, we can allocate skb in mcu_send_msg routine. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: use band parameter for LC calibrationStanislaw Gruszka1-2/+3
We use always 1 as band parameter for MCU_CAL_LC, this break 2GHz, we should use 0 for this band instead. Patch fixes problems happened sometimes when try to associate with 2GHz AP and manifest by errors like below: [14680.920823] wlan0: authenticate with 18:31:bf:c0:51:b0 [14681.109506] wlan0: send auth to 18:31:bf:c0:51:b0 (try 1/3) [14681.310454] wlan0: send auth to 18:31:bf:c0:51:b0 (try 2/3) [14681.518469] wlan0: send auth to 18:31:bf:c0:51:b0 (try 3/3) [14681.726499] wlan0: authentication with 18:31:bf:c0:51:b0 timed out Fixes: 9aec146d0f6b ("mt76x0: pci: introduce mt76x0_phy_calirate routine") Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: phy: use tssi reported value to configure tx power if availableLorenzo Bianconi2-5/+17
Use tssi calibrated value to configure tx power gain if tssi is enabled in eeprom data Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: phy: introduce tssi calibration supportLorenzo Bianconi3-3/+357
Run mt76x0 tssi calibration process if enabled in eeprom data. Perform calibration procedure every 4s Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_eeprom_copy in mt76x02-lib moduleLorenzo Bianconi3-13/+17
Move mt76x02_eeprom_copy utility routine in mt76x02-lib module in order to be reused by mt76x0 driver adding tssi calibration support Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x2u: init: use common routines for wcid/key initializationLorenzo Bianconi1-12/+7
Use mt76x02_mac_wcid_setup and mt76x02_mac_shared_key_setup for shared keys and wcid table initialization and remove duplicated code Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x2u: init: remove not useful configurationLorenzo Bianconi1-3/+0
Remove MT_TSO_CTRL and MT_HEADER_TRANS_CTRL_REG initialization since it is already done in mt76_write_mac_initvals routine Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: init: use mt76x02_mac_wcid_setup for wcid configurationLorenzo Bianconi1-43/+2
Use mt76x02_mac_wcid_setup utility routine for wcid init configuration and remove duplicated code. This patch fixes a mt76x0 AP issue since hw key table selection was set to pairwise by default Fixes: dbad2adcb2c7 ("mt76x0: pci: enable AP support") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x2: move wcid_tx_rate conf at bootstrapLorenzo Bianconi2-4/+4
Move WCID tx rate configuration at device bootstrap since the related register are always set to 0 Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: init: use mt76x02_mac_shared_key_setup in mt76x0_init_hardwareLorenzo Bianconi1-9/+4
Use mt76x02_mac_shared_key_setup utility routine for shared key initialization and remove duplicated code Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: phy: use mt76_poll_msec in mt76x0_phy_temp_sensorLorenzo Bianconi1-2/+1
Use mt76_poll_msec utility routine for CORE_R34 register polling instead of mt76_poll in order to allow the hw to complete requested calibration since on slow devices (e.g. mt7620 based boards) calibration takes longer than 2ms Fixes: 66a34c66e0cb ("mt76x0: phy: add phy/vco temperature compensation") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: do not overwrite other MT_BBP(AGC, 8) fieldsStanislaw Gruszka1-3/+1
MT_BBP(AGC, 8) register has values depend on band in mt76x0_bbp_switch_tab, so we should not overwrite other fields than MT_BBP_AGC_GAIN when setting gain. This can fix performance issues when connecting to 2.4GHz AP. Fixes: 4636a2544c3b ("mt76x0: phy: align channel gain logic to mt76x2 one") Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: add support for reporting tx status with skbFelix Fietkau11-95/+231
MT76x2/MT76x0 has somewhat unreliable tx status reporting, and for that reason the driver currently does not report per-skb tx ack status at all. This breaks things like client idle polling, which relies on the tx ack status of a transmitted nullfunc frame. This patch adds code to report skb-attached tx status if requested by mac80211 or the rate control module. Since tx status is polled from a simple FIFO register, the code needs to account for the possibility of tx status events getting lost. The code keeps a list of skbs for which tx status is required and passes them to mac80211 once tx status has been filled in and the DMA queue is done with it. If a tx status event is not received after one second, the status rates are cleared, and a succesful ACK is indicated to avoid spurious disassoc during assoc or client polling. Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: mt76x02: only override control->sta on sw-encrypted txFelix Fietkau1-1/+3
control->sta is set to NULL early when encryption is turned on for the station and info->control.hw_key is not set. This code is missing a check for the 802.11 header protected flag, otherwise it resets the station for other frames, e.g. client probing frames. Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: mt76x02: skip station tx status for non-sta wcid entriesFelix Fietkau1-1/+1
Fixes a crash that could occur if a frame is sent to a station, but the station's wcid was not used (e.g. for software encrypted mgmt tx) Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: clean up more unused EXPORT_SYMBOLsFelix Fietkau3-10/+1
Make functions static where possible Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: pci: add DFS supportLorenzo Bianconi7-33/+49
Introduce dfs support in mt76x0e driver and unlock radar channels Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move dfs support in mt76x02-lib moduleLorenzo Bianconi8-102/+83
Move mt76x2 DFS support in mt76x02-lib module in order to be reused by mt76x0 driver and unlock DFS frequencies Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_bss_info_changed in mt76x02-lib moduleLorenzo Bianconi7-92/+48
Unify drv_bss_info_changed mac80211 callback and remove duplicated code in mt76x0 and mt76x2 drivers Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move tx protection routines in mt76x02-lib moduleLorenzo Bianconi14-171/+54
Move mt76x02_set_rts_threshold and mt76x02_mac_set_tx_protection routines in mt76x02-lib module and remove duplicated code in mt76x0 and mt76x2 drivers. Remove pci_mac.c and mt76x0/mac.c since now are empty files Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: update init vals for MT_TX_PROT registersLorenzo Bianconi1-6/+9
Add missing VHT MT_TX_PROT register init values Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_set_tx_ackto in mt76x02-lib moduleLorenzo Bianconi7-34/+39
Move mt76x02_set_tx_ackto and mt76x02_set_coverage_class routines in mt76x02-lib module in order to be reused by mt76x0 driver. This is a preliminary patch to unify drv_bss_info_changed mac80211 callback between mt76x0 and mt76x2 drivers Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: pci: enable AP supportLorenzo Bianconi4-39/+32
Add missing mac80211 callbacks to mt76x0e_ops data structure and add mt76x02_beacon utility routines in mt76x0_bss_info_changed in order to enable/disable beacon transmission Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: introduce mt76x02_init_beacon_config routineLorenzo Bianconi4-28/+31
Add mt76x02_init_beacon_config utility routine in mt76x02-lib module in order to be reused by mt76x0 driver configuring BSSID registers and remove duplicated code Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_sta_ps in mt76x02-lib moduleLorenzo Bianconi6-14/+15
Move mt76x02_sta_ps utility routine in mt76x02_util.c in order to be reused by mt76x0 driver adding AP support Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_get_txpower in mt76x02_util.cLorenzo Bianconi6-14/+24
Move mt76x02_get_txpower utility routine in mt76x02-lib module in order to be reused by mt76x0 and mt76x2u drivers Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_sw_scan and mt76x02_sw_scan_complete in mt76x02-lib moduleLorenzo Bianconi8-66/+34
Move mt76x02_sw_scan and mt76x02_sw_scan_complete utility routines in mt76x02_util.c in order to be reused by mt76x0 and mt76x2u drivers and remove duplicated code Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: pci: add pre_tbtt_tasklet supportLorenzo Bianconi5-7/+7
Enable/disable pre_tbtt_tasklet in mt76x0 driver in order to add AP support Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move tx beacon routines in mt76x02-lib moduleLorenzo Bianconi6-147/+130
Move mt76x02_tx beacon utility routines in mt76x02_mmio.c in order to be reused by mt76x0 driver adding AP support Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mac beacon routines in mt76x02-lib moduleLorenzo Bianconi7-129/+135
Move mt76x02_beacon mac routines in mt76x02_mac.c in order to be reused by mt76x0 driver adding AP support Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_init_device in mt76x02-lib moduleLorenzo Bianconi8-114/+87
Move mt76x02_init_device routine in mt76x02_util.c in order to be reused by mt76x0 driver and remove duplicated code. Move interface combo definition supported by the driver in mt76x02_init_device routine Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_mac_set_short_preamble in mt76x02_mac.cLorenzo Bianconi5-10/+11
Move mt76x02_mac_set_short_preamble routine in mt76x02-lib module since it is shared between mt76x0 and mt76x2 drivers Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: align mt76x0u and mt76x0e fw versionLorenzo Bianconi3-4/+23
Unify firmware version used on mt76x0e and mt76x0u drivers. Fallback to mt7610u fw if mt7610e one is not available Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: mac: remove mt76x0_mac_set_ampdu_factorLorenzo Bianconi2-26/+0
Remove no longer used mt76x0_mac_set_ampdu_factor routine Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: pci: add missing MODULE_FIRMWARE macroLorenzo Bianconi3-3/+5
Add missing firmware declaration for mt76x0e driver Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: init: simplify mt76x0_init_mac_registersLorenzo Bianconi1-17/+10
Simplify mt76x0_init_mac_registers routine using mt76_set, mt76_clear and mt76_rmw utility routines Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: antenna select correctionsStanislaw Gruszka2-18/+44
Update mt76x0_phy_ant_select() to conform vendor driver, most notably add dual antenna mode support, read configuration from EEPROM and move ant select out of channel config to init phase. Plus small MT7630E quirk for MT_CMB_CTRL register which vendor driver dedicated to this chip do. This make MT7630E workable with mt76x0e driver and do not cause any problems on MT7610U for me. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: usb: fix static tracepointsLorenzo Bianconi10-347/+38
Add submit_urb and rx_urb static tracepoints in mt76-usb module. Move trace_mac_txstat_fetch in mt76x02_mac_load_tx_status routine in order to be available to usb drivers. Moreover remove no longer used mt76x0/trace.{c,h} Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: mt76x0: handle chip specific initval differencesFelix Fietkau2-4/+49
Some RF registers need different values for various chips. For at least mt76x0_rf_central_tab registers, overwriting them later does not work, as the wrong values can cause the entire system to hang on some devices with MT7610E Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: clean up unused leftover EXPORT_SYMBOLsFelix Fietkau6-18/+3
Make previously exported functions static where possible Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: do not perform MCU calibration for MT7630Stanislaw Gruszka2-0/+8
Driver works better for MT7630 without MCU calibration, which looks like it can hangs the firmware. Vendor driver do not perform it for MT7630 as well. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: phy: unify calibration between mt76x0u and mt76x0eLorenzo Bianconi4-84/+4
Align phy calibration logic between mt76x0u and mt76x0e drivers This patch improves connection stability with low SNR Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x2u: introduce mac workqueue supportLorenzo Bianconi4-1/+5
Add mac workqueue support to mt76x2u driver in order to compute device statistics and add mac stuck routine Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-26 22:23:30 +0300