summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2020-10-21drm/i915: Restore ILK-M RPS supportVille Syrjälä1-0/+1
Restore RPS for ILK-M. We lost it when an extra HAS_RPS() check appeared in intel_rps_enable(). Unfortunaltey this just makes the performance worse on my ILK because intel_ips insists on limiting the GPU freq to the minimum. If we don't do the RPS init then intel_ips will not limit the frequency for whatever reason. Either it can't get at some required information and thus makes wrong decisions, or we mess up some weights/etc. and cause it to make the wrong decisions when RPS init has been done, or the entire thing is just wrong. Would require a bunch of reverse engineering to figure out what's going on. Cc: stable@vger.kernel.org Cc: Chris Wilson <chris@chris-wilson.co.uk> Fixes: 9c878557b1eb ("drm/i915/gt: Use the RPM config register to determine clk frequencies") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201021131443.25616-1-ville.syrjala@linux.intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
2020-10-21drm/i915: Enable scaling filter for plane and CRTCPankaj Bharadiya4-4/+32
GEN >= 10 hardware supports the programmable scaler filter. Attach scaling filter property for CRTC and plane for GEN >= 10 hardwares and program scaler filter based on the selected filter type. changes since v3: * None changes since v2: * Use updated functions * Add ps_ctrl var to contain the full PS_CTRL register value (Ville) * Duplicate the scaling filter in crtc and plane hw state (Ville) changes since v1: * None Changes since RFC: * Enable properties for GEN >= 10 platforms (Ville) * Do not round off the crtc co-ordinate (Danial Stone, Ville) * Add new functions to handle scaling filter setup (Ville) * Remove coefficient set 0 hardcoding. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-5-pankaj.laxminarayan.bharadiya@intel.com
2020-10-21drm/i915/display: Add Nearest-neighbor based integer scaling supportPankaj Bharadiya2-0/+103
Integer scaling (IS) is a nearest-neighbor upscaling technique that simply scales up the existing pixels by an integer (i.e., whole number) multiplier.Nearest-neighbor (NN) interpolation works by filling in the missing color values in the upscaled image with that of the coordinate-mapped nearest source pixel value. Both IS and NN preserve the clarity of the original image. Integer scaling is particularly useful for pixel art games that rely on sharp, blocky images to deliver their distinctive look. Introduce functions to configure the scaler filter coefficients to enable nearest-neighbor filtering. Bspec: 49247 changes since v6: * Trust compiler, remove pointless inline keyword from cnl_coef_tap() & cnl_nearest_filter_coef() functions (Ville) changes since v4: * Make cnl_coef_tap(), cnl_nearest_filter_coef() inline (Uma) changes since v3: * None changes since v2: * Move APIs from 5/5 into this patch. * Change filter programming related function names to cnl_*, move filter select bits related code into inline function (Ville) changes since v1: * Rearrange skl_scaler_setup_nearest_neighbor_filter() to iterate the registers directly instead of the phases and taps (Ville) changes since RFC: * Refine the skl_scaler_setup_nearest_neighbor_filter() logic (Ville) Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-4-pankaj.laxminarayan.bharadiya@intel.com
2020-10-21drm/i915: Introduce scaling filter related registers and bit fieldsPankaj Bharadiya1-0/+22
Introduce scaler registers and bit fields needed to configure the scaling filter in prgrammed mode and configure scaling filter coefficients. changes since v3: * None changes since v2: * Change macro names to CNL_* and use +(set)*8 instead of adding another trip through _PICK_EVEN (Ville). changes since v1: * None changes since RFC: * Parametrize scaler coeffient macros by 'set' (Ville) Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-3-pankaj.laxminarayan.bharadiya@intel.com
2020-10-21drm: Introduce plane and CRTC scaling filter propertiesPankaj Bharadiya7-0/+174
Introduce per-plane and per-CRTC scaling filter properties to allow userspace to select the driver's default scaling filter or Nearest-neighbor(NN) filter for upscaling operations on CRTC and plane. Drivers can set up this property for a plane by calling drm_plane_create_scaling_filter() and for a CRTC by calling drm_crtc_create_scaling_filter(). NN filter works by filling in the missing color values in the upscaled image with that of the coordinate-mapped nearest source pixel value. NN filter for integer multiple scaling can be particularly useful for for pixel art games that rely on sharp, blocky images to deliver their distinctive look. changes since: v6: * Move property doc to existing "Standard CRTC Properties" and "Plane Composition Properties" doc comments (Simon) changes since v3: * Refactor code, add new function for common code (Ville) changes since v2: * Create per-plane and per-CRTC scaling filter property (Ville) changes since v1: * None changes since RFC: * Add separate properties for plane and CRTC (Ville) Link: https://github.com/xbmc/xbmc/pull/18194 Link: https://github.com/xbmc/xbmc/pull/18567 Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> Acked-by: Simon Ser <contact@emersion.fr> Acked-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-2-pankaj.laxminarayan.bharadiya@intel.com
2020-10-21drm/i915/display: Rename pipe_timings to transcoder_timingsManasi Navare1-11/+11
No functional changes in this patch. With Bigjoiner, there are 2 pipes driving 2 halfs of 1 transcoder. The transcoder_mode has the full timings, and is used for configuring the transcoder with the intended mode after joining the 2 halves. To clear the confusion, we rename intel_set_pipe_timings to intel_set_transcoder_timings v2: * Split the renaming into separate patch (Ville) Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Manasi Navare <manasi.d.navare@intel.com> Reviewed-by: Animesh Manna <animesh.manna@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201008214535.22942-2-manasi.d.navare@intel.com
2020-10-20drm/i915: Sort ICL PCI IDsVille Syrjälä1-8/+8
Sort the ICL PCI IDs numerically. Some order seems better than randomness. Cc: Alexei Podtelezhnikov <apodtele@gmail.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-14-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Sort CNL PCI IDsVille Syrjälä1-9/+9
Sort the CNL PCI IDs numerically. Some order seems better than randomness. Cc: Alexei Podtelezhnikov <apodtele@gmail.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-13-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Sort CFL PCI IDsVille Syrjälä1-2/+2
Sort the CFL PCI IDs numerically. Some order seems better than randomness. Cc: Alexei Podtelezhnikov <apodtele@gmail.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-12-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Sort CML PCI IDsVille Syrjälä1-6/+6
Sort the CML PCI IDs numerically. Some order seems better than randomness. Cc: Alexei Podtelezhnikov <apodtele@gmail.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-11-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Sort KBL PCI IDsVille Syrjälä1-4/+4
Sort the KBL PCI IDs numerically. Some order seems better than randomness. Cc: Alexei Podtelezhnikov <apodtele@gmail.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-10-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Sort SKL PCI IDsVille Syrjälä1-4/+4
Sort the SKL PCI IDs numerically. Some order seems better than randomness. Cc: Alexei Podtelezhnikov <apodtele@gmail.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-9-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Sort HSW PCI IDsVille Syrjälä1-17/+17
Sort the HSW PCI IDs numerically. Some order seems better than randomness. Cc: Alexei Podtelezhnikov <apodtele@gmail.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-8-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Ocd the HSW PCI ID hex numbersVille Syrjälä1-3/+3
Most of the HSW PCI IDs are upper case hex numbers, but a few are lower case. Make it consistent so these don't stick out like a sore thumb. Cc: Alexei Podtelezhnikov <apodtele@gmail.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-7-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Try to fix the SKL GT3/4 vs. GT3e/4e commentsVille Syrjälä1-6/+6
Bunch of the SKL SKUs currently documented as GT3/4 seem to actually be GT3e/4e. Fix up the comments. Cc: Alexei Podtelezhnikov <apodtele@gmail.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-6-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Add SKL GT1.5 PCI IDsAlexei Podtelezhnikov1-3/+6
Add three new devices 0x1913, 0x1915, and 0x1917 also known as iSKLULTGT15, iSKLULXGT15, and iSKLDTGT15. Signed-off-by: Alexei Podtelezhnikov <apodtele@gmail.com> [vsyrjala: Split separate changes into separate patchs, Sort the IDs] Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-5-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Reclassify SKL 0x1923 and 0x1927 as ULTAlexei Podtelezhnikov1-3/+3
Reclassify 0x1923, 0x1927 according to specifications. Of note, the second to last digit seems to correspond to GT#. Signed-off-by: Alexei Podtelezhnikov <apodtele@gmail.com> [vsyrjala: Split separate changes into separate patches, Sort the IDs] Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-4-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Reclassify SKL 0x192a as GT3Alexei Podtelezhnikov1-1/+1
Reclassify 0x192A according to specifications. Of note, the second to last digit seems to correspond to GT#. Signed-off-by: Alexei Podtelezhnikov <apodtele@gmail.com> [vsyrjala: Split separate changes into separate patches] Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-3-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Update Haswell PCI IDsAlexei Podtelezhnikov1-1/+1
Reclassify 0x0426 as GT3 (GT2+) according to specifications and the second least significant digit. Signed-off-by: Alexei Podtelezhnikov <apodtele@gmail.com> [vsyrjala: s/GT2/GT3/ in the comment] Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-2-ville.syrjala@linux.intel.com Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
2020-10-20drm/i915: Sort the mess around ICP TC hotplugs regsVille Syrjälä1-107/+106
Move the DSC stuff out from the middle of the ICP HPD register definitions. The location seems to have been selected by a dice roll. SHPD_FILTER_CNT addition also went astray due to the DSC mess, so we also fix that vs. ICP_TC_HPD_{SHORT,LONG}_DETECT(). Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201006143349.5561-2-ville.syrjala@linux.intel.com Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
2020-10-20drm/i915: Refactor .hpd_irq_setup() calls a bitVille Syrjälä1-10/+12
Add a small wrapper for .hpd_irq_setup() which does the "do we even have the hook?" and "are display interrupts enabled?" checks. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201006185809.4655-3-ville.syrjala@linux.intel.com Reviewed-by: Imre Deak <imre.deak@intel.com>
2020-10-20drm/i915: Reorder hpd init vs. display resumeVille Syrjälä5-34/+46
Currently we call .hpd_irq_setup() directly just before display resume, and follow it with another call via intel_hpd_init() just afterwards. Assuming the hpd pins are marked as enabled during the open-coded call these two things do exactly the same thing (ie. enable HPD interrupts). Which even makes sense since we definitely need working HPD interrupts for MST sideband during the display resume. So let's nuke the open-coded call and move the intel_hpd_init() call earlier. However we need to leave the poll_init_work stuff behind after the display resume as that will trigger display detection while we're resuming. We don't want that trampling over the display resume process. To make this a bit more symmetric we turn this into a intel_hpd_poll_{enable,disable}() pair. So we end up with the following transformation: intel_hpd_poll_init() -> intel_hpd_poll_enable() lone intel_hpd_init() -> intel_hpd_init()+intel_hpd_poll_disable() .hpd_irq_setup()+resume+intel_hpd_init() -> intel_hpd_init()+resume+intel_hpd_poll_disable() If we really would like to prevent all *long* HPD processing during display resume we'd need some kind of software mechanism to simply ignore all long HPDs. Currently we appear to have that just for fbdev via ifbdev->hpd_suspended. Since we aren't exploding left and right all the time I guess that's mostly sufficient. For a bit of history on this, we first got a mechanism to block hotplug processing during suspend in commit 15239099d7a7 ("drm/i915: enable irqs earlier when resuming") on account of moving the irq enable earlier. This then got removed in commit 50c3dc970a09 ("drm/fb-helper: Fix hpd vs. initial config races") because the fdev initial config got pushed to a later point. The second ad-hoc hpd_irq_setup() for resume was added in commit 0e32b39ceed6 ("drm/i915: add DP 1.2 MST support (v0.7)") to be able to do MST sideband during the resume. And finally we got a partial resurrection of the hpd blocking mechanism in commit e8a8fedd57fd ("drm/i915: Block fbdev HPD processing during suspend"), but this time it only prevent fbdev from handling hpd while resuming. v2: Leave the poll_init_work behind v3: Remove the extra intel_hpd_poll_disable() from display reset (Lyude) Add the missing intel_hpd_poll_disable() to display init (Imre) Cc: Lyude Paul <lyude@redhat.com> Cc: Imre Deak <imre.deak@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201013181137.30560-1-ville.syrjala@linux.intel.com Reviewed-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Lyude Paul <lyude@redhat.com>
2020-10-20drm/i915: s/intel_dp_sink_dpms/intel_dp_set_power/Ville Syrjälä4-17/+17
Rename intel_dp_sink_dpms() to intel_dp_set_power() so one doesn't always have to convert from the DPMS enum values to the actual DP D-states. Also when dealing with a branch device this has nothing to do with any sink, so the old name was nonsense anyway. Also adjust the debug message accordingly, and pimp it with the standard encoder id+name thing. Trivial bits done with cocci: @@ expression DP; @@ ( - intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF) + intel_dp_set_power(DP, DP_SET_POWER_D3) | - intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON) + intel_dp_set_power(DP, DP_SET_POWER_D0) ) Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com Reviewed-by: Imre Deak <imre.deak@intel.com>
2020-10-20drm/i915: Move the lspcon resume from .reset() to intel_dp_sink_dpms()Ville Syrjälä1-3/+2
Rather that try to trick LSPCON back into PCON mode from the .reset() hook let's just do that as a regular part of the normal modeset sequence, which is going to take care of the system resume case. During a normal modeset this should normally be a nop as the mode should have already been switched by .detect(). Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-1-ville.syrjala@linux.intel.com Reviewed-by: Imre Deak <imre.deak@intel.com>
2020-10-20drm/i915: Drop runtime-pm assert from vgpu io accessorsChris Wilson1-1/+26
The "mmio" writes into vgpu registers are simple memory traps from the guest into the host. We do not need to assert in the guest that the device is awake for the io as we do not write to the device itself. However, over time we have refactored all the mmio accessors with the result that the vgpu reuses the gen2 accessors and so inherits the assert for runtime-pm of the native device. The assert though has actually been there since commit 3be0bf5acca6 ("drm/i915: Create vGPU specific MMIO operations to reduce traps"). References: 3be0bf5acca6 ("drm/i915: Create vGPU specific MMIO operations to reduce traps") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Yan Zhao <yan.y.zhao@intel.com> Cc: Zhenyu Wang <zhenyuw@linux.intel.com> Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com> Cc: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20200811092532.13753-1-chris@chris-wilson.co.uk
2020-10-20drm/i915: Force VT'd workarounds when running as a guest OSChris Wilson1-1/+5
If i915.ko is being used as a passthrough device, it does not know if the host is using intel_iommu. Mixing the iommu and gfx causes a few issues (such as scanout overfetch) which we need to workaround inside the driver, so if we detect we are running under a hypervisor, also assume the device access is being virtualised. Reported-by: Stefan Fritsch <sf@sfritsch.de> Suggested-by: Stefan Fritsch <sf@sfritsch.de> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Zhenyu Wang <zhenyuw@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Stefan Fritsch <sf@sfritsch.de> Cc: stable@vger.kernel.org Tested-by: Stefan Fritsch <sf@sfritsch.de> Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201019101523.4145-1-chris@chris-wilson.co.uk
2020-10-20drm/i915/display/fbc: Implement WA 22010751166José Roberto de Souza1-0/+7
Underruns happens when plane height + y offset is not a modulo of 4 when FBC is enabled. It happens when scanline is at vactive - 10 but that is not feasible to do from the software side so here completely disabling FBC when height + y offset matches to avoid visual glitches. Specification says that it only affects TGL display C stepping and newer but to simply the check and as TGL is already in final costumers hands, pre-production display stepping A and B was also included. BSpec: 52887 ICL BSpec: 52888 EHL/JSL BSpec: 52890/55378 TGL BSpec: 53508 DG1 BSpec: 53273 RKL Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201019175609.28715-1-jose.souza@intel.com
2020-10-20drm/i915/display: Program DBUF_CTL tracker state serviceJosé Roberto de Souza2-5/+23
This sequence is not part of "Sequences to Initialize Display" but as noted in the MBus page the DBUF_CTL.Tracker_state_service needs to be set to 8. BSpec: 49213 Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201019173906.18892-1-jose.souza@intel.com
2020-10-16drm/i915: Inline intel_dp_ycbcr420_config()Ville Syrjälä1-24/+9
intel_dp_ycbcr420_config() is rather pointless. Just inline it directly into intel_dp_compute_config(). This gets rid of the ugly double assignment of output_format. Not really sure what the best policy would be when the user supplies a mode classified by the display as "YCbCr 4:2:0 only", but we know that we can't do YCbCr 4:2:0 output. For now keep the current behaviour of just silently upgrade it to RGB 4:4:4. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200924184156.24491-3-ville.syrjala@linux.intel.com Reviewed-by: Uma Shankar <uma.shankar@intel.com>
2020-10-16drm/i915: Nuke lspcon_ycbcr420_config()Ville Syrjälä3-21/+3
Remove the lspcon special case from intel_dp_compute_config() and just treat it like any other DFP than can do 4:4:4->4:2:0 conversion. The only difference between the two codepaths was that the lspcon code tried to already halve port_clock. That was just total nonsense as we hadn't even computed the base port_clock at that time. All that stuff happens intel_dp_compute_link_config*() and it already takes care of the 4:2:0 clock reduction. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200924184156.24491-2-ville.syrjala@linux.intel.com Reviewed-by: Uma Shankar <uma.shankar@intel.com>
2020-10-16drm/i915: Nuke lspcon_downsamplingVille Syrjälä3-23/+12
crtc_state->lspcon_downsampling isn't particularly useful at the moment since we can't even do proper readout for it. Let's get rid of it. Will help with unifying the LSPCON with the regular DFP YCbCr output support. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200924184156.24491-1-ville.syrjala@linux.intel.com Reviewed-by: Uma Shankar <uma.shankar@intel.com>
2020-10-16drm/i915: Mark initial fb obj as WT on eLLC machines to avoid rcu lockup ↵Ville Syrjälä1-0/+8
during fbdev init Currently we leave the cache_level of the initial fb obj set to NONE. This means on eLLC machines the first pin_to_display() will try to switch it to WT which requires a vma unbind+bind. If that happens during the fbdev initialization rcu does not seem operational which causes the unbind to get stuck. To most appearances this looks like a dead machine on boot. Avoid the unbind by already marking the object cache_level as WT when creating it. We still do an excplicit ggtt pin which will rewrite the PTEs anyway, so they will match whatever cache level we set. Cc: <stable@vger.kernel.org> # v5.7+ Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2381 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201007120329.17076-1-ville.syrjala@linux.intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
2020-10-16drm/i915: Apply WAC6entrylatency to kbl/cflVille Syrjälä1-0/+8
WAC6entrylatency is trying to fix excessive rc6 entry latency caused by the extra delay from FBC_LLC_READ_CTRL, which is there for some extra sync with uncore for frame buffer caching in LLC. Reading through the hsd the recommendation was to set the FBC_LLC_FULLY_OPEN bit to disable this extra delay entirely. This can be done whenever fb LLC caching is not used. The alternative suggestion was to reduce the delay to eg. 0x5 via updated BIOS programming instructions. But all the kbl/cfl machines I've seen still have the default 0xff programmed. As we never use fb LLC caching let's just apply the w/a to all skl derivatives to get consistent rc6 latencies. I was able to measure the effect of FBC_LLC_READ_CTRL to rc6 latency via forcewake. Here's a graph of some of the results: sleep;fw_req=1;wait fw_ack==1;sleep;fw_req=0;wait fw_ack==0 fw_ack==1 duration 160us +----------------------------------------------------------------+ | + + $$+ + + | | $$ $ $ ******$$ ** $ $**$* #########$$######| 140us |-$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$*$$$$$$$$$$$$$$$$ $$$$$$| | $ * # | | $ * # | 120us |$+ * # +-| |$ * # | |$ * # # | 100us |$+ ************######################## +-| |$ * *# | |$ ***** ######### | 80us |$+ * # #### ## +-| |$ **** ### # # | | ** #### FBC_LLC_READ_CTRL: 0x8000 ******* | 60us |-###### FBC_LLC_READ_CTRL: 0xffff #######-| |## + + FBC_LLC_READ_CTRL: 0x400000ff $$$$$$$ | +----------------------------------------------------------------+ 0ms 10ms 20ms 30ms 40ms 50ms 60ms sleep duration The default FBC_LLC_READ_CTRL value of 0xff is documented to give us a 170usec delay. That tracks well with the knees at 0xffff->~44msec and 0x8000->~22msec we see in the graph. We can see that if we sleep longer than the FBC_LLC_READ_CTRL delay we always observe the full (~145usec) rc6 wakeup latency. But if we sleep for less than the FBC_LLC_READ_CTRL delay we see a quicker fw wakeup, presumably due the hardware not having yet entered rc6 fully. The other plateaus in the graph I suspect correspond to some shallower internal rc states. v2: s/usec/msec/ typo in commit msg Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200716190426.17047-2-ville.syrjala@linux.intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
2020-10-16drm/i915/rkl: Add new cdclk tableMatt Roper1-1/+31
A recent bspec update has provided a new cdclk table for RKL. All of the cdclk values are the same as those we've been using on ICL, TGL, etc., but we obtain them by doubling both the PLL ratio and CD2X divider numbers. Bspec: 49202 Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201015220038.271740-1-matthew.d.roper@intel.com
2020-10-16drm/i915/dgfx: define llc and snooping behaviourMichel Thierry1-0/+2
While we do lack the faster shared LLC, we should still have support for snooping over PCIe. Signed-off-by: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Matthew Auld <matthew.auld@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-11-lucas.demarchi@intel.com
2020-10-16drm/i915/dg1: Update DMC_DEBUG registerAnshuman Gupta2-2/+8
Update the DMC_DEBUG_DC5 register to its new location and do not try reading the DC6 counter since DG1 doesn't support DC6. v2: Use IS_DGFX() instead of IS_DG1(). Even if not having DC6 is not directly related to DGFX, the register move to a new location is. So in future, if there is one supporting DC6, it would just need to add the other register rather than fixing the case of a wrong register being read (Matt) Cc: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-10-lucas.demarchi@intel.com
2020-10-16drm/i915/dg1: DG1 does not support DC6Anshuman Gupta1-1/+4
DC6 is not supported on DG1, so change the allowed DC mask for DG1. This is not yet on bspec, but it has been confirmed by HW engineers. Cc: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-9-lucas.demarchi@intel.com
2020-10-16drm/i915/dg1: Add initial DG1 workaroundsStuart Summers6-44/+131
DG1 shares some workarounds with TGL and RKL and also has some additional workarounds of its own. v2: Correct location of Wa_1408615072 (JohnH). v3: Apply WAs 1606700617, 18011464164 and 22010931296 to DG1 (José) v4 (Anusha) - Add Wa_22010271021 - s/Wa_14010096844/Wa_1409836686 v5: - Extend Wa_14010919138 to all revs (Matt Atwood) - Power gate media is global gen12 design. (Rodrigo) - Rebase (Lucas) v6: use REG_BIT() to fix checkpatch warning (Lucas) BSpec: 53508 Cc: Matt Atwood <matthew.s.atwood@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Signed-off-by: Stuart Summers <stuart.summers@intel.com> Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-8-lucas.demarchi@intel.com
2020-10-16drm/i915/dg1: Load DMCMatt Atwood1-3/+9
Add support to load DMC v2.0.2 on DG1 While we're at it, make TGL use the same GEN12 firmware size definition and remove obsolete comment. Bpec: 49230 v2: do not replace GEN12_CSR_MAX_FW_SIZE (from José) and replace stale comment Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-7-lucas.demarchi@intel.com
2020-10-16drm/i915/dg1: Enable DPLL for DG1Lucas De Marchi2-4/+8
Add DG1 DPLL Enable register macro and use the macro to enable the correct DPLL based on PLL id. Although we use _MG_PLL1_ENABLE/_MG_PLL2_ENABLE these are rather combo phys. While at it, fix coding style: wrong newlines and use if/else chain v2: Rewrite original patch from Aditya Swarup based on refactors upstream Bspec: 49443, 49206 Cc: Clinton Taylor <Clinton.A.Taylor@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Aditya Swarup <aditya.swarup@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Aditya Swarup <aditya.swarup@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-6-lucas.demarchi@intel.com
2020-10-16drm/i915/dg1: Add and setup DPLLs for DG1Aditya Swarup1-4/+38
Add entries for dg1 plls and setup dg1_pll_mgr to reuse ICL callbacks. Initial setup for shared dplls DPLL0/1 for DDIA/DDIB and DPLL2/3 for DDI-TC1/DDI-TC2. Configure dpll cfgcrx registers to drive the plls on DG1. v2 (Lucas): Reword commit message and add missing update_ref_clks hook (requested by Matt Roper) Signed-off-by: Aditya Swarup <aditya.swarup@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-5-lucas.demarchi@intel.com
2020-10-16drm/i915/dg1: Add DPLL macros for DG1Aditya Swarup2-1/+33
DG1 has 4 DPLLs where DPLL0 and DPLL1 drive DDIA/B and DPLL2 and DPLL3 drive DDI-TC1/DDI-TC2. Introduce DG1_DPLL_CFCRx() helper macros to configure DPLL registers. Bspec: 50288, 50299 Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Aditya Swarup <aditya.swarup@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-4-lucas.demarchi@intel.com
2020-10-16drm/i915/dg1: Add DG1 power wellsLucas De Marchi2-2/+6
TGL power wells can be re-used for DG1 with the exception of the fake power well for TC_COLD. v2: use logic to skip power wells while copying instead of duplicating the definition of TGL power wells (Matt Roper) Bspec: 49182 Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-3-lucas.demarchi@intel.com
2020-10-16drm/i915/cnl: skip PW_DDI_F on certain skusLucas De Marchi2-12/+9
The skus guarded by IS_CNL_WITH_PORT_F() have port F and thus they need those power wells. The others don't have those. Up to now we were just overriding the number of power wells on !IS_CNL_WITH_PORT_F(), relying on those power wells to be the last ones. Now that we have logic in place to skip power wells by id, use it instead. Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-2-lucas.demarchi@intel.com
2020-10-16drm/i915/display: allow to skip certain power wellsAditya Swarup1-6/+18
This allows us to skip power wells on a platform allowing it to re-use the table from another one instead of having to create a new table from scratch that is basically a copy with a few removals. Cc: Imre Deak <imre.deak@intel.com> Suggested-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Aditya Swarup <aditya.swarup@intel.com> [ Adapt ignore logic to be based on pw id rather than adding a new field, as suggested by Imre ] Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-1-lucas.demarchi@intel.com
2020-10-14drm/i915/jsl: Split EHL/JSL platform info and PCI idsTejas Upadhyay16-38/+54
Recently we came across requirement to identify EHL and JSL platform to program them differently. Thus Split the basic platform definition, macros, and PCI IDs to differentiate between EHL and JSL platforms. Also, IS_ELKHARTLAKE is replaced with IS_JSL_EHL everywhere. Changes since V1 : - Rebased to avoid merge conflicts - Added missed check for jasperlake in intel_uc_fw.c Cc : Matt Roper <matthew.d.roper@intel.com> Cc : Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201013192948.63470-1-tejaskumarx.surendrakumar.upadhyay@intel.com
2020-10-13drm/i915: Force DPCD backlight mode for BOE 2270 panelAaron Ma1-0/+1
BOE 2270 panel failed to control backlight brightness. Add it in edid quirks to force using DPCD backlight control. Then the brightness can be controlled. Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201009085750.88490-2-aaron.ma@canonical.com
2020-10-13drm/i915/dpcd_bl: uncheck PWM_PIN_CAP when detect eDP backlight capabilitiesAaron Ma1-2/+1
BOE panel with ID 2270 claims both PWM_PIN_CAP and AUX_SET_CAP backlight control bits, but default chip backlight failed to control brightness. Check AUX_SET_CAP and proceed to check quirks or VBT backlight type. DPCD can control the brightness of this pannel. Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201009085750.88490-1-aaron.ma@canonical.com
2020-10-13drm/i915/dp: Tweak initial dpcd backlight.enabled valueSean Paul1-11/+20
In commit 79946723092b ("drm/i915: Assume 100% brightness when not in DPCD control mode"), we fixed the brightness level when DPCD control was not active to max brightness. This is as good as we can guess since most backlights go on full when uncontrolled. However in doing so we changed the semantics of the initial 'backlight.enabled' value. At least on Pixelbooks, they were relying on the brightness level in DP_EDP_BACKLIGHT_BRIGHTNESS_MSB to be 0 on boot such that enabled would be false. This causes the device to be enabled when the brightness is set. Without this, brightness control doesn't work. So by changing brightness to max, we also flipped enabled to be true on boot. To fix this, make enabled a function of brightness and backlight control mechanism. Fixes: 79946723092b ("drm/i915: Assume 100% brightness when not in DPCD control mode") Cc: Lyude Paul <lyude@redhat.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com> Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Kevin Chowski <chowski@chromium.org>> Signed-off-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200918002845.32766-1-sean@poorly.run
2020-10-12drm/i915: Switch to LTTPR non-transparent mode link trainingImre Deak5-73/+321
The DP Standard's recommendation is to use the LTTPR non-transparent mode link training if LTTPRs are detected, so let's do this. Besides power-saving, the advantages of this are that the maximum number of LTTPRs can only be used in non-transparent mode (the limit is 5-8 in transparent mode), and it provides a way to narrow down the reason for a link training failure to a given link segment. Non-transparent mode is probably also the mode that was tested the most by the industry. The changes in this patchset: - Pass the DP PHY that is currently link trained to all LT helpers, so that these can access the correct LTTPR/DPRX DPCD registers. - During LT take into account the LTTPR common lane rate/count and the per LTTPR-PHY vswing/pre-emph limits. - Switch to LTTPR non-transparent LT mode and train each link segment according to the sequence in DP Standard v2.0 (complete CR/EQ for each segment before continuing with the next segment). v2: - Switch to non-transparent mode during connector detection, which is required before reading the per-PHY LTTPR capabilities. - Move the DP_PHY_LTTPR() macro to drm_dp_helper.h (Ville) - Use the new drm_dp_dpcd_read_phy_link_status() instead of adding the same logic to intel_dp_get_link_status(). (Ville) - Make intel_dp_lttpr_phy_caps() return a pointer to the whole array instead of a pointer to its first element. (Ville) - Add the intel_dp_phy_is_downstream_of_source() helper. (Ville) - Add a code comment about the disable->enable quirk of non-transparent mode. - Add the intel_dp_training_pattern_set_reg() helper. - Fix checkpatch/sparse warns. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-7-imre.deak@intel.com
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-27 21:51:48 +0300