| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
'asoc/topic/tas3a227e' and 'asoc/topic/tas571x' into asoc-next
|
|
'asoc/topic/ssm2602', 'asoc/topic/ssm4567' and 'asoc/topic/sta32x' into asoc-next
|
|
'asoc/topic/sgtl5000' into asoc-next
|
|
'asoc/topic/pxa', 'asoc/topic/qcom' and 'asoc/topic/rcar' into asoc-next
|
|
'asoc/topic/gtm601', 'asoc/topic/intel', 'asoc/topic/lm3857' and 'asoc/topic/max98090' into asoc-next
|
|
'asoc/topic/fsl-spdif', 'asoc/topic/fsl-ssi' and 'asoc/topic/gpio-jack' into asoc-next
|
|
into asoc-next
|
|
'asoc/topic/cs35l32' and 'asoc/topic/da7210' into asoc-next
|
|
'asoc/topic/arizona' and 'asoc/topic/atmel' into asoc-next
|
|
'asoc/topic/ada1977', 'asoc/topic/adau1701' and 'asoc/topic/adau17x1' into asoc-next
|
|
|
|
|
|
|
|
|
|
'asoc/fix/wm8955' into asoc-linus
|
|
'asoc/fix/max98925', 'asoc/fix/rcar' and 'asoc/fix/ux500' into asoc-linus
|
|
|
|
Instead of hard wiring the WCLK frequency at probe time do it runtime.
The hard wired 88_96KHz was not even setting the correct bits since it was
defined as (1 << 6) which will change the I2S_OUT_SEL bit and will leave
the amplifier configured for 8KHz.
At the same time clean up and fix the CFG3 register bits.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Configure the word length based on the params_width of the stream.
Also configure the clock per frame value which is used when tas2552 is bus
master.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Certain sequence need to be followed in order to have smooth power up and
power down performance.
Execute this sequence via DAPM_POST widget.
Remove patching the RESERVED_0D register at probe time since it has to be
handled every time when we stop or start the amplifier.
In order to be able to execute the sequence at the correct time, the driver
need to request to ignore the pmdown time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The last parameter for DECLARE_TLV_DB_SCALE() is to tell if the gain will
be muted or not when it is set to raw 0. IN this case it is not muted.
The PGA_GAIN is in 0-4 bits in the register. Fix the offset in the
SOC_SINGLE_TLV() for this.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The strings should be: 'static const char * const tas2552_input_texts[]'
SOC_DAPM_ENUM should have "Route" in place of xname and no need to have it
as an array.
Also align the parameters.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
TDM support is achieved using DSP transfer mode and setting a programmable
offset which specifies where data begins with respect to the frame sync.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use names from the datasheet for the definitions.
Correct the data format definitions since they were not correct.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DSP_A mode require one bit delay from the FS, DSP_B is without data delay.
When checking the requested format, also match the bit and fs inversion
flag along with the format since it is not possible to change inversion.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Instead of hard wiring the PLL_CLKIN and PDM_CLK to be sourced from BCLK add
proper clock configuration via the set_dai_sysclk callback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Binding header file for clock input selection and configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Resource management
- Fix IOV sorting by alignment (Wei Yang)
- Preserve resource size during alignment reordering (Yinghai Lu)
Miscellaneous
- MAINTAINERS: Add Pratyush for SPEAr13xx and DesignWare PCIe (Pratyush Anand)"
* tag 'pci-v4.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Preserve resource size during alignment reordering
PCI: Fix IOV resource sorting by alignment requirement
MAINTAINERS: Add Pratyush Anand as SPEAr13xx and DesignWare PCIe maintainer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"It was a fairly calm week; here you can find only a few trivial quirks
and fixes for USB and HD-audio. All changes are pretty device
specific"
* tag 'sound-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: fix missing input volume controls in MAYA44 USB(+)
ALSA: usb-audio: add MAYA44 USB+ mixer control names
ALSA: hda/realtek - Add a fixup for another Acer Aspire 9420
ALSA: hda - Fix jack detection at resume with VT codecs
ALSA: usb-audio: don't try to get Outlaw RR2150 sample rate
ALSA: usb-audio: Add mic volume fix quirk for Logitech Quickcam Fusion
ALSA: hda/realtek - Suooprt Dell headset mode for ALC256
|
|
Prevents frequent panic on boot, if the irq handler rt5645_irq
gets called before the workqueue rt5645_jack_detect_work is
initialized.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fix from Joerg Roedel:
"Only one patch:
- Revert "iommu/amd: Don't allocate with __GFP_ZERO in
alloc_coherent".
This patch caused problems with some drivers, so it is better to
revert it now until the drivers have been fixed"
* tag 'iommu-fixes-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
Revert "iommu/amd: Don't allocate with __GFP_ZERO in alloc_coherent"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- early_idt_handlers[] fix that fixes the build with bleeding edge
tooling
- build warning fix on GCC 5.1
- vm86 fix plus self-test to make it harder to break it again"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm/irq: Stop relying on magic JMP behavior for early_idt_handlers
x86/asm/entry/32, selftests: Add a selftest for kernel entries from VM86 mode
x86/boot: Add CONFIG_PARAVIRT_SPINLOCKS quirk to arch/x86/boot/compressed/misc.h
x86/asm/entry/32: Really make user_mode() work correctly for VM86 mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"The biggest chunk of the changes are two regression fixes: a HT
workaround fix and an event-group scheduling fix. It's been verified
with 5 days of fuzzer testing.
Other fixes:
- eBPF fix
- a BIOS breakage detection fix
- PMU driver fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/pt: Fix a refactoring bug
perf/x86: Tweak broken BIOS rules during check_hw_exists()
perf/x86/intel/pt: Untangle pt_buffer_reset_markers()
perf: Disallow sparse AUX allocations for non-SG PMUs in overwrite mode
perf/x86: Improve HT workaround GP counter constraint
perf/x86: Fix event/group validation
perf: Fix race in BPF program unregister
|
|
Pull drm fixes from Dave Airlie:
"Just two small fixes: one radeon, one amdkfd"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/amdkfd: fix topology bug with capability attr.
drm/radeon: use proper ACR regisiter for DCE3.2
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c bug fixes from Wolfram Sang:
"Two small bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: s3c2410: fix oops in suspend callback for non-dt platforms
i2c: hix5hd2: Fix modalias to make module auto-loading work
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.1-rc7
Here are a couple of new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
On some v7 devices (e.g. Lenovo-E550) the deltas reported are typically
only in the 0-1 range dividing this by 2 results in a range of 0-0.
And even for v7 devices where this does not lead to making the trackstick
entirely unusable, it makes it twice as slow as before we added v7 support
and were using the ps/2 mouse emulation of the dual point setup.
If some kind of generic slowdown is actually necessary for some devices,
then that belongs in userspace, not in the kernel.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Rico Moorman <rico.moorman@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds new icbody type to the list recognized by Elantech PS/2 driver.
Cc: stable@vger.kernel.org
Signed-off-by: Sam Hung <sam.hung@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
If SRIOV is enabled we need to be in VEB mode not VEPA mode at probe.
This fixes an NPAR bug when SRIOV is enabled in the BIOS.
Change-ID: Ibf006abafd9a0ca3698ec24848cd771cf345cbbc
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The patch fixes a bug in the default configuration which
prevented a software bridge loaded on the PF interface from
working correctly because broadcast packets are incorrectly
looped back.
Fix the general case, by loading the driver in VEPA mode Until a
VF or VMDq VSI is added. This way loopback on the Main VSI is
turned off until needed and can resolve the issue of unnecessary
reflection for users that do not have VF or VMDq VSIs setup.
The driver must now coordinate the loopback setting for the Flow
Director (FDIR) VSI to make sure it is in sync with the current
VEB or VEPA mode setting.
The user can still switch bridge modes from the bridge commands and
choose to be in VEPA mode with VF VSIs. Because of hardware
requirements, the call to switch to VEB mode when no VF/VMDqs are
present will be rejected.
NOTE: This patch uses BIT_ULL as that is preferred going forward,
a followup patch in the lower priority queue to net-next will fix
up the remaining 1 << usages.
Change-ID: Ib121ddb18fe4b3c4f52e9deda6fcbeb9105683d1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes a bug where the i40e Tx queue will hang if this
skb is passed to the driver.
With mixed size fragments while using TSO there was a corner case
where we needed to linearize but we were not. This was seen with
iSCSI traffic and could be reproduced with a frag list that looks
like this:
num_frags = 17, gso_segs = 17, hdr_len = 66,
skb_shinfo(skb)->gso_size = 1448
size = 3002, j = 1, frag_size = 2936, num_frags = 17
size = 4268, j = 1, frag_size = 4096, num_frags = 16
size = 5534, j = 1, frag_size = 4096, num_frags = 15
size = 5352, j = 1, frag_size = 4096, num_frags = 14
size = 5170, j = 1, frag_size = 4096, num_frags = 13
size = 3468, j = 1, frag_size = 2576, num_frags = 12
size = 750, j = 1, frag_size = 112, num_frags = 11
size = 862, j = 2, frag_size = 112, num_frags = 10
size = 974, j = 3, frag_size = 112, num_frags = 9
size = 1126, j = 4, frag_size = 152, num_frags = 8
size = 1330, j = 5, frag_size = 204, num_frags = 7
size = 1534, j = 6, frag_size = 204, num_frags = 6
size = 356, j = 1, frag_size = 204, num_frags = 5
size = 560, j = 2, frag_size = 204, num_frags = 4
size = 764, j = 3, frag_size = 204, num_frags = 3
size = 968, j = 4, frag_size = 204, num_frags = 2
size = 1140, j = 5, frag_size = 172, num_frags = 1
result: linearize = 0, j = 6
Change-ID: I79bb1aeab0af255fe2ce28e93672a85d85bf47e8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
"IS_ENABLED(PPC_PSERIES)" always evaluates to false, as IS_ENABLED() is
supposed to be used with the full Kconfig symbol name, including the
"CONFIG_" prefix.
Add the missing "CONFIG_" prefix to fix this.
Fixes: a25095d451ece23b ("of: Move dynamic node fixups out of powerpc and into common code")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org #+3.17
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
In the functions compat_get_bitmap() and compat_put_bitmap() the
variable nr_compat_longs stores how many compat_ulong_t words should be
copied in a loop.
The copy loop itself is this:
if (nr_compat_longs-- > 0) {
if (__get_user(um, umask)) return -EFAULT;
} else {
um = 0;
}
Since nr_compat_longs gets unconditionally decremented in each loop and
since it's type is unsigned this could theoretically lead to out of
bounds accesses to userspace if nr_compat_longs wraps around to
(unsigned)(-1).
Although the callers currently do not trigger out-of-bounds accesses, we
should better implement the loop in a safe way to completely avoid such
warp-arounds.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
|
|
Added the USB serial device ID for the HubZ dual ZigBee
and Z-Wave radio dongle.
Signed-off-by: John D. Blair <johnb@candicontrols.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Pull dmaengine fixes from Vinod Koul:
"We have two small fixes:
- pl330 termination hang fix by Krzysztof
- hsu memory leak fix by Peter"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: hsu: Fix memory leak when stopping a running transfer
dmaengine: pl330: Fix hang on dmaengine_terminate_all on certain boards
|
|
sound/soc/zte/zx296702-i2s.c:428:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
MCLK is one of the possible source for the pll_clkin frequency. Make this
clear by renaming the variable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The function name and parameters of:
tas2552_sw_shutdown(struct tas2552_data *tas_data, int sw_shutdown)
implies that if sw_shutdown is 1 we should be entering to the software
shutdown mode.
The code can be simplified as well within the function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Initialize the cfg1_reg to 0 and set the mute bit only when it is needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove the _MASK postfix of the bit definitions, collect the CFG1 bit
definition in one place and correct the bit shifts at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
