| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The same hardware issue the at91 must work around applies to at least the
Zynq ethernet, and possibly more devices. The driver also needs to handle
the RXUBR interrupt since it turns it on with MACB_RX_INT_FLAGS anyway.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sowmini Varadhan says:
====================
net/rds: RDS-TCP robustness fixes
This patch-set contains bug fixes for state-recovery at the RDS
layer when the underlying transport is TCP and the TCP state at one
of the endpoints is reset
V2 changes: DaveM comments to reduce memory footprint, follow
NFS/RPC model where possible. Added test-case #3
Without the changes in this set, when one of the endpoints is reset,
the existing code does not correctly clean up RDS socket state for stale
connections, resulting in some unstable, timing-dependant behavior on
the wire, including an infinite exchange of 3WHs back-and-forth, and a
resulting potential to never converge RDS state.
Test cases used to verify the changes in this set are:
1. Start rds client/server applications on two participating nodes,
node1 and node2. After at least one packet has been sent (to establish
the TCP connection), restart the rds_tcp module on the client, and
now resend packets. Tcpdump should show server sending a FIN for the
"old" client port, and clean connection establishment/exchange for
the new client port.
2. At the end of step 1, restart rds srever on node2, and start client on
node1, make sure using tcpdump, 'netstat -an|grep 16385' that
packets flow correctly.
3. start RDS client/server application on two participating nodes, and
repeat steps 1 and 2, but this time, simulate node failure by doing
"ifconfig <intf> down", so no FIN is sent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the peer of an RDS-TCP connection restarts, a reconnect
attempt should only be made from the active side of the TCP
connection, i.e. the side that has a transient TCP port
number. Do not add the passive side of the TCP connection
to the c_hash_node and thus avoid triggering rds_queue_reconnect()
for passive rds connections.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running RDS over TCP, the active (client) side connects to the
listening ("passive") side at the RDS_TCP_PORT. After the connection
is established, if the client side reboots (potentially without even
sending a FIN) the server still has a TCP socket in the esablished
state. If the server-side now gets a new SYN comes from the client
with a different client port, TCP will create a new socket-pair, but
the RDS layer will incorrectly pull up the old rds_connection (which
is still associated with the stale t_sock and RDS socket state).
This patch corrects this behavior by having rds_tcp_accept_one()
always create a new connection for an incoming TCP SYN.
The rds and tcp state associated with the old socket-pair is cleaned
up via the rds_tcp_state_change() callback which would typically be
invoked in most cases when the client-TCP sends a FIN on TCP restart,
triggering a transition to CLOSE_WAIT state. In the rarer event of client
death without a FIN, TCP_KEEPALIVE probes on the socket will detect
the stale socket, and the TCP transition to CLOSE state will trigger
the RDS state cleanup.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there are only IPv6 source specific default routes present, the
host gets -ENETUNREACH on e.g. connect() because ip6_dst_lookup_tail
calls ip6_route_output first, and given source address any, it fails,
and ip6_route_get_saddr is never called.
The change is to use the ip6_route_get_saddr, even if the initial
ip6_route_output fails, and then doing ip6_route_output _again_ after
we have appropriate source address available.
Note that this is '99% fix' to the problem; a correct fix would be to
do route lookups only within addrconf.c when picking a source address,
and never call ip6_route_output before source address has been
populated.
Signed-off-by: Markus Stenberg <markus.stenberg@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
Here are a couple of important Bluetooth & mac802154 fixes for 4.1:
- mac802154 fix for crypto algorithm allocation failure checking
- mac802154 wpan phy leak fix for error code path
- Fix for not calling Bluetooth shutdown() if interface is not up
Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We cast away the volatile, but really, why make it volatile at all?
We already do a mb() inside the cpumask_empty() loop.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This fixes a dumb bug in fs_fully_visible that allows proc or sys to
be mounted if there is a bind mount of part of /proc/ or /sys/ visible.
Cc: stable@vger.kernel.org
Reported-by: Eric Windisch <ewindisch@docker.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
To install tmon we issue "make install" which produces bellow error.
root@odroidxu3:/usr/src/odroidxu3-4.y-testing/tools/thermal/tmon# make install
mkdir -p /usr/bin
install -m 755 -p "tmon" "/usr/bin/tmon"
mkdir -p /
install -m 644 -p "" "/"
install: cannot stat ‘’: No such file or directory
make: [install] Error 1 (ignored)
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
There is a copy and paste bug, "->clk" vs "->pclk", so we return the
wrong error code here.
Fixes: cbac8f639437 ('thermal: rockchip: add driver for thermal')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Package C8 to C10 was introduced in newer Intel CPUs, we need to
include them in the package c-state residency calculation.
Otherwise, idle injection target is not accurately maintained by
the closed control loop.
Also cleaned up the code to make it scale better with large number
of c-states.
Reported-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Broadwell server has support for package C-states, idle injection works
as expected on this platform.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Mark the module init / exit functions with __init / __exit accodingly.
This allows making the intel_powerclamp_ids[] array __initconst, too, as
it only gets referenced from powerclamp_probe(). This is safe as
file2alias doesn't care about the section, but the symbol name for the
MODULE_DEVICE_TABLE alias.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes for bugs caught while digging in fs/namei.c. The
first one is this cycle regression, the second is 3.11 and later"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
path_openat(): fix double fput()
namei: d_is_negative() should be checked before ->d_seq validation
|
|
path_openat() jumps to the wrong place after do_tmpfile() - it has
already done path_cleanup() (as part of path_lookupat() called by
do_tmpfile()), so doing that again can lead to double fput().
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Fetching ->d_inode, verifying ->d_seq and finding d_is_negative() to
be true does *not* mean that inode we'd fetched had been NULL - that
holds only while ->d_seq is still unchanged.
Shift d_is_negative() checks into lookup_fast() prior to ->d_seq
verification.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"When an arm user reported crashes near page_address(page) in my new
code, it became clear that I can't be trusted with GFP masks. Filipe
beat me to the patch, and I'll just be in the corner with my dunce cap
on"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix wrong mapping flags for free space inode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two additional fixes for changes introduced via DM during the 4.1
merge window.
The first reverts a dm-crypt change that wasn't correct. The second
fixes a device format regression that impacted userspace"
* tag 'dm-4.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
init: fix regression by supporting devices with major:minor:offset format
Revert "dm crypt: fix deadlock when async crypto algorithm returns -EBUSY"
|
|
Pull block fixes from Jens Axboe:
"A collection of fixes since the merge window;
- fix for a double elevator module release, from Chao Yu. Ancient bug.
- the splice() MORE flag fix from Christophe Leroy.
- a fix for NVMe, fixing a patch that went in in the merge window.
From Keith.
- two fixes for blk-mq CPU hotplug handling, from Ming Lei.
- bdi vs blockdev lifetime fix from Neil Brown, fixing and oops in md.
- two blk-mq fixes from Shaohua, fixing a race on queue stop and a
bad merge issue with FUA writes.
- division-by-zero fix for writeback from Tejun.
- a block bounce page accounting fix, making sure we inc/dec after
bouncing so that pre/post IO pages match up. From Wang YanQing"
* 'for-linus' of git://git.kernel.dk/linux-block:
splice: sendfile() at once fails for big files
blk-mq: don't lose requests if a stopped queue restarts
blk-mq: fix FUA request hang
block: destroy bdi before blockdev is unregistered.
block:bounce: fix call inc_|dec_zone_page_state on different pages confuse value of NR_BOUNCE
elevator: fix double release of elevator module
writeback: use |1 instead of +1 to protect against div by zero
blk-mq: fix CPU hotplug handling
blk-mq: fix race between timeout and CPU hotplug
NVMe: Fix VPD B0 max sectors translation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a bunch of GPIO fixes that I collected since -rc1, nothing
controversial, nothing special:
- fix a memory leak for GPIO hotplug.
- fix a signedness bug in the ACPI GPIO pin validation.
- driver fixes: Qualcomm SPMI and OMAP MPUIO IRQ issues"
* tag 'gpio-v4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: omap: Fix regression for MPUIO interrupts
gpio: sysfs: fix memory leaks and device hotplug
pinctrl: qcom-spmi-gpio: Fix input value report
pinctrl: qcom-spmi-gpio: Fix output type configuration
gpiolib: change gpio pin from unsigned to signed in acpi callback
|
|
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Don't access RPMB partitions for normal read/write
- Fix hibernation restore sequence
MMC host:
- dw_mmc: Fix card detection for non removable cards
- dw_mmc: Fix sglist issue in 32-bit mode
- sh_mmcif: Fix timeout value for command request"
* tag 'mmc-4.1-rc2' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: dw_mmc: dw_mci_get_cd check MMC_CAP_NONREMOVABLE
mmc: dw_mmc: init desc in dw_mci_idmac_init
mmc: card: Don't access RPMB partitions for normal read/write
mmc: sh_mmcif: Fix timeout value for command request
mmc: core: add missing pm event in mmc_pm_notify to fix hib restore
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"The newly added ftrace_print_array_seq() function had a bug in it.
Luckily, the only user of it didn't make the 4.1 merge window.
But the helper function should be fixed before 4.2 when the users
start coming in"
* tag 'trace-fixes-v4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Make ftrace_print_array_seq compute buf_len
|
|
The reset code functionality is mostly a copy paste between OMAP4+ and
AM33xx+. Re-use the omap4 code where possible, and just keep the special
implementation for de-asserting the hardreset lines for AM33xx, as
AM33xx+ devices have slightly different register layouts compared to
OMAP4+. This patch also fixes the hardreset issues faced on AM43xx.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
AM43xx has slightly different reset register layout compared to OMAP4+,
with varying status bit shifts and status register offsets. Current
code assumes static offsets and identical status / reset control bit
shifts, which is wrong. This patch adds PRM core support for passing
the actual implementations from hwmod code. AM43xx mappings will be fixed
in subsequent patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
This patch adds VPFE HWMOD data for AM43xx.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Benoit Parrot <bparrot@ti.com>
[paul@pwsan.com: updated to apply on v4.1-rc1]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.
So Suspend-to-RAM and Suspend-to-idle are failing on Exynos5250 Snow.
Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Remove the extra zero in the "cpu-crit-0" trip point for exynos5420
and exynos5440.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The Exynos4412 SoC has a s3c6410 RTC where the source clock
is now a mandatory property.
This patch fixes probe failure of s3c-rtc on Odroid-X2/U2/U3 boards.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Commit ea08de16eb1b ("ARM: dts: Add DISP1 power domain for exynos5420")
added a device node for the Exynos5420 DISP1 power domain but dit not
make the DP controller a consumer of that power domain.
This causes an "Unhandled fault: imprecise external abort" error if the
exynos-dp driver tries to access the DP controller registers and the PD
was turned off. This lead to a kernel panic and a complete system hang.
Make the DP controller device node a consumer of the DISP1 power domain
to ensure that the PD is turned on when the exynos-dp driver is probed.
Fixes: ea08de16eb1b ("ARM: dts: Add DISP1 power domain for exynos5420")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This adds Baruch as the maintainer for the Digicolor platform.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The git tree at rocketboards.org is going away. Update the entry to reflect
the address of the new location. Also add an entry for all the socfpga_*
dts files.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Consider "(u64)insn1.imm << 32 | imm" in the arm64 JIT. Since imm is
signed 32-bit, it is sign-extended to 64-bit, losing the high 32 bits.
The fix is to convert imm to u32 first, which will be zero-extended to
u64 implicitly.
Cc: Zi Shen Lim <zlim.lnx@gmail.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: 30d3d94cc3d5 ("arm64: bpf: add 'load 64-bit immediate' instruction")
Signed-off-by: Xi Wang <xi.wang@gmail.com>
[will: removed non-arm64 bits and redundant casting]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Tegra would not only need a hardware vblank counter that
increments at leading edge of vblank, but also support
for instantaneous high precision vblank timestamp queries, ie.
a proper implementation of dev->driver->get_vblank_timestamp().
Without these, there can be off-by-one errors during vblank
disable/enable if the scanout is inside vblank at en/disable
time, and additionally clients will never see any useable
vblank timestamps when querying via drmWaitVblank ioctl. This
would negatively affect swap scheduling under X11 and Wayland.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://people.freedesktop.org/~gabbayo/linux into drm-fixes
- Add missing initialization of SDMA vm register when creating an SDMA queue
- Don't report local memory size, as we don't support local memory allocation
yet.
- Allow to unregister process with exisiting queues. Until now we blocked
it with BUG_ON, which was also an error by itself.
* tag 'drm-amdkfd-fixes-2015-05-07' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: Initialize sdma vm when creating sdma queue
drm/amdkfd: Don't report local memory size
drm/amdkfd: allow unregister process with queues
|
|
into drm-fixes
Mostly stability fixes for UVD and VCE, plus a few other bug and regression
fixes.
* 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: stop trying to suspend UVD sessions
drm/radeon: more strictly validate the UVD codec
drm/radeon: make UVD handle checking more strict
drm/radeon: make VCE handle check more strict
drm/radeon: fix userptr lockup
drm/radeon: fix userptr BO unpin bug v3
drm/radeon: don't setup audio on asics that don't support it
drm/radeon: disable semaphores for UVD V1 (v2)
|
|
iTLB-load-misses and LLC-load-misses count incorrectly on SLM.
There is no ITLB.MISSES support on SLM. Event PAGE_WALKS.I_SIDE_WALK
should be used to count iTLB-load-misses. This event counts when an
instruction (I) page walk is completed or started. Since a page walk
implies a TLB miss, the number of TLB misses can be counted by counting
the number of pagewalks.
DMND_DATA_RD counts both demand and DCU prefetch data reads. However,
LLC-load-misses should only count demand reads. There is no way to not
include prefetches with a single counter on SLM. So the LLC-load-misses
support should be removed on SLM.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1429608881-5055-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
While fuzzing Sasha tripped over another ctx->mutex recursion lockdep
splat. Annotate this.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit 3c18d447b3b3 ("sched/core: Check for available DL bandwidth in
cpuset_cpu_inactive()"), a SCHED_DEADLINE bugfix, had a logic error that
caused a regression in setting a CPU inactive during suspend. I ran into
this when a program was failing pthread_setaffinity_np() with EINVAL after
a suspend+wake up.
A simple reproducer:
$ ./a.out
sched_setaffinity: Success
$ systemctl suspend
$ ./a.out
sched_setaffinity: Invalid argument
... where ./a.out is:
#define _GNU_SOURCE
#include <errno.h>
#include <sched.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <unistd.h>
int main(void)
{
long num_cores;
cpu_set_t cpu_set;
int ret;
num_cores = sysconf(_SC_NPROCESSORS_ONLN);
CPU_ZERO(&cpu_set);
CPU_SET(num_cores - 1, &cpu_set);
errno = 0;
ret = sched_setaffinity(getpid(), sizeof(cpu_set), &cpu_set);
perror("sched_setaffinity");
return ret ? EXIT_FAILURE : EXIT_SUCCESS;
}
The mistake is that suspend is handled in the action ==
CPU_DOWN_PREPARE_FROZEN case of the switch statement in
cpuset_cpu_inactive().
However, the commit in question masked out CPU_TASKS_FROZEN
from the action, making this case dead.
The fix is straightforward.
Signed-off-by: Omar Sandoval <osandov@osandov.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 3c18d447b3b3 ("sched/core: Check for available DL bandwidth in cpuset_cpu_inactive()")
Link: http://lkml.kernel.org/r/1cb5ecb3d6543c38cce5790387f336f54ec8e2bc.1430733960.git.osandov@osandov.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Ronny reported that the following scenario is not handled correctly:
T1 (prio = 10)
lock(rtmutex);
T2 (prio = 20)
lock(rtmutex)
boost T1
T1 (prio = 20)
sys_set_scheduler(prio = 30)
T1 prio = 30
....
sys_set_scheduler(prio = 10)
T1 prio = 30
The last step is wrong as T1 should now be back at prio 20.
Commit c365c292d059 ("sched: Consider pi boosting in setscheduler()")
only handles the case where a boosted tasks tries to lower its
priority.
Fix it by taking the new effective priority into account for the
decision whether a change of the priority is required.
Reported-by: Ronny Meeus <ronny.meeus@gmail.com>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: <stable@vger.kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Fixes: c365c292d059 ("sched: Consider pi boosting in setscheduler()")
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1505051806060.4225@nanos
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There is no need for special handling of stripe-batches when the array
is degraded.
There may be if there is a failure in the batch, but STRIPE_DEGRADED
does not imply an error.
So don't set STRIPE_BATCH_ERR in ops_run_io just because the array is
degraded.
This actually causes a bug: the STRIPE_DEGRADED flag gets cleared in
check_break_stripe_batch_list() and so the bitmap bit gets cleared
when it shouldn't.
So in check_break_stripe_batch_list(), split the batch up completely -
again STRIPE_DEGRADED isn't meaningful.
Also don't set STRIPE_BATCH_ERR when there is a write error to a
replacement device. This simply removes the replacement device and
requires no extra handling.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
As the new 'scribble' array is sized based on chunk size,
we need to make sure the size matches the largest of 'old'
and 'new' chunk sizes when the array is undergoing reshape.
We also potentially need to resize it even when not resizing
the stripe cache, as chunk size can change without changing
number of devices.
So move the 'resize' code into a separate function, and
consider old and new sizes when allocating.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 46d5b785621a ("raid5: use flex_array for scribble data")
|
|
If any memory allocation in resize_stripes fails we will return
-ENOMEM, but in some cases we update conf->pool_size anyway.
This means that if we try again, the allocations will be assumed
to be larger than they are, and badness results.
So only update pool_size if there is no error.
This bug was introduced in 2.6.17 and the patch is suitable for
-stable.
Fixes: ad01c9e3752f ("[PATCH] md: Allow stripes to be expanded in preparation for expanding an array")
Cc: stable@vger.kernel.org (v2.6.17+)
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When performing a reconstruct write, we need to read all blocks
that are not being over-written .. except the parity (P and Q) blocks.
The code currently reads these (as they are not being over-written!)
unnecessarily.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: ea664c8245f3 ("md/raid5: need_this_block: tidy/fix last condition.")
|
|
It is not incorrect to call handle_stripe_fill() when
a batch of full-stripe writes is active.
It is, however, a BUG if fetch_block() then decides
it needs to actually fetch anything.
So move the 'BUG_ON' to where it belongs.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 59fc630b8b5f ("RAID5: batch adjacent full stripe write")
|
|
The new batch_lock and batch_list fields are being initialized in
grow_one_stripe() but not in resize_stripes(). This causes a crash
on resize.
So separate the core initialization into a new function and call it
from both allocation sites.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 59fc630b8b5f ("RAID5: batch adjacent full stripe write")
|
|
This patch is a prerequisite for dm-raid "raid0" support to allow
dm-raid to access the MD RAID0 personality doing unconditional
accesses to mddev->queue, which is NULL in case of dm-raid stacked on
top of MD.
Most of the conditional mddev->queue accesses made it to upstream but
this missing one, which prohibits md raid0 to set disk stack limits
(being done in dm core in case of md underneath dm).
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Tested-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When non-removable is used for emmc, MMC_CAP_NONREMOVABLE should
also be checked, otherwise detection fail since present=0
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Set 0 to des1 in 32bit case.
Otherwise the random value of des1 will be used in
dw_mci_translate_sglist: IDMAC_SET_BUFFER1_SIZE(desc, length)
Signed-off-by: Fei Wang <w.f@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These include three regression fixes (PCI resources management,
ACPI/PNP device enumeration, ACPI SBS on MacBook) and two ACPI
documentation fixes related to GPIO.
Specifics:
- Fix for a PCI resources management regression introduced during the
4.0 cycle and related to the handling of ACPI resources'
Producer/Consumer flags that turn out to be useless (Jiang Liu)
- Fix for a MacBook regression related to the Smart Battery Subsystem
(SBS) driver causing various problems (stalls on boot, failure to
detect or report battery) to happen and introduced during the 3.18
cycle (Chris Bainbridge)
- Fix for an ACPI/PNP device enumeration regression introduced during
the 3.16 cycle caused by failing to include two PNP device IDs into
the list of IDs that PNP device objects need to be created for
(Witold Szczeponik)
- Fixes for two minor mistakes in the ACPI GPIO properties
documentation (Antonio Ospite, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PNP: add two IDs to list for PNPACPI device enumeration
ACPI / documentation: Fix ambiguity in the GPIO properties document
ACPI / documentation: fix a sentence about GPIO resources
ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook
x86/PCI/ACPI: Make all resources except [io 0xcf8-0xcff] available on PCI bus
|
|
* acpi-resources:
x86/PCI/ACPI: Make all resources except [io 0xcf8-0xcff] available on PCI bus
* acpi-battery:
ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook
* acpi-doc:
ACPI / documentation: Fix ambiguity in the GPIO properties document
ACPI / documentation: fix a sentence about GPIO resources
* acpi-pnp:
ACPI / PNP: add two IDs to list for PNPACPI device enumeration
|
