summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2011-10-19xHCI/USB: Make xHCI driver have a BOS descriptor.Sarah Sharp2-2/+50
To add USB 3.0 link power management (LPM), we need to know what the U1 and U2 exit latencies are for the xHCI host controller. External USB 3.0 hubs report these values through the SuperSpeed Capabilities descriptor in the BOS descriptor. Make the USB 3.0 roothub for the xHCI host behave like an external hub and return the BOS descriptors. The U1 and U2 exit latencies will vary across each host controller, so we need to dynamically fill those values in by reading the exit latencies out of the xHC registers. Make the roothub code in the USB core handle hub_control() returning the length of the data copied. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-10-13usb: gadget: add new usb gadget for ACM and mass storageKlaus Schwarzkopf3-0/+268
This driver provides two functions in one configuration: a mass storage, and a ACM (serial port) link. Heavily based on multi.c and cdc2.c Signed-off-by: Klaus Schwarzkopf <schwarzkopf@sensortherm.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: fix compile warningFelipe Balbi1-1/+1
| drivers/usb/gadget/mv_udc_core.c: In function 'handle_setup_packet': | drivers/usb/gadget/mv_udc_core.c:1556:6: warning: 'status' may be \ used uninitialized in this function Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: add clock gating supportNeil Zhang2-11/+185
This patch is going to support clock gating when vbus detection is posible. Clock and phy will be on only when usb gadget is used(vbus valid). Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: add test mode supportNeil Zhang2-19/+54
Add test mode support for marvell udc driver. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: use DMA API for status_req's dma addressNeil Zhang1-1/+8
use DMA API for status_req's dma address, it is needed by dtd. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: fix dtd dma confusionNeil Zhang1-1/+26
The controller will prime failure sometimes when do the iperf test. Add delay to wait controller release dtd dma before we free it. Then the issue is gone. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: add shutdown function for itNeil Zhang1-0/+12
put the device in idle when shutdown. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: correct ep0 stateNeil Zhang1-2/+3
This patch is going to correct the ep0 state, and the unexpected ep0 package warning can be removed. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: rewrite fifo flushNeil Zhang1-27/+18
1: Add parameter check. 2: For controller endpoint, we need to flush in and out directions. 3: delete redundant code, make it more readable. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: set unused endpoint with right typeNeil Zhang1-2/+2
According to the comment right above the code, we should use USB_ENDPOINT_XFER_BULK instead. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: add missing spinlock in ep enable/disableNeil Zhang1-3/+13
The ep enable / disable functions can be called from interrupt context, and they are not race safe on SMP systems. The critical data can be modified in more than one routing. Make them race safe by using IRQ-safe spinlock functions. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: fix bug when handle setup package.Neil Zhang1-2/+1
For the code doesn't restrict controller ep must be ep0, so we will go through all the eps and check if there is a setup package received. And also we just need to acknowledge the corresponding bit in ENDPTSETUPSTAT register. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: init next dtd ptr for dqh when init ep0Neil Zhang1-0/+2
Set next dtd ptr to EP_QUEUE_HEAD_NEXT_TERMINATE for dqh when init ep0. It means the dQH is empty. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: ep0 needn't set toggle flagNeil Zhang1-2/+2
According to ChipIdea datasheet, there is no toggle flag for ep0. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: fix a clerical errorNeil Zhang1-1/+1
The max size of data payload is in bit0 - bit10, so we need use 0x7ff as the bitmask to fetch from usb_endpoint_descriptor.wMaxPacketSize. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: fix kernel panic on some platformsNeil Zhang1-0/+7
Some platforms will use usb to download images, the controller may not be stopped correctly when start kernel. In some cases, it may have some pending interrupts, and they will be triggered immediately when we finish requesting irq in function probe. But we haven't finished the device initialization at this time. So let's stop udc here to avoid this case occurred. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: add section informationNeil Zhang1-2/+2
Tag the probe function as __devinit. Tag the remove function as __devexit. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: mv_udc: refine the driver structureNeil Zhang5-259/+182
This patch do the following things: 1. Add header and Copyright for marvell usb driver. 2. Add mv_usb.h in include/linux/platform_data, make the driver fits all the marvell platform using the same ChipIdea usb ip. 3. Some SOC may has mutiple clock sources, so let me define it in mv_usb_platform_data and give two helper functions named udc_clock_enable/udc_clock_disable to deal with the clocks. 4. Different SOCs will have some difference in PHY initialization, so we will remove file mv_udc_phy.c and add two funtions in mv_usb_platform_data, let the platform relative driver to realize it. 5. Rewrite probe function according to the modification list above. Find it will kernel panic when probe failed. The root cause is as follows: When probe failed, the error handle may call device_unregister() which in return will call gadget_release.In current code, gadget_release have two issues: 1: the_controller is a NULL pointer. 2: if we free udc here, then the following code in probe will access NULL pointer. Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: fix compile warningFelipe Balbi1-2/+2
| drivers/usb/renesas_usbhs/fifo.c: In function ‘usbhsf_dma_prepare_push’: | drivers/usb/renesas_usbhs/fifo.c:823:7: warning: cast from pointer \ to integer of different size [-Wpointer-to-int-cast] | drivers/usb/renesas_usbhs/fifo.c: In function ‘usbhsf_dma_try_pop’: | drivers/usb/renesas_usbhs/fifo.c:900:7: warning: cast from pointer \ to integer of different size [-Wpointer-to-int-cast] Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: drop dependencyFelipe Balbi1-1/+0
that driver can compile cleanly on x86 without any issues. Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: fixup driver compile styleKuninori Morimoto3-4/+12
In current renesas-usbhs, there was inconsistency about the style of kernel module or built-in. This patch solve it. [ balbi@ti.com : fix compile issue when building modules ] Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: bugfix: don't modify platform dataKuninori Morimoto3-14/+18
renesas_usbhs has default callback functions and settings. And it tried overwrite to platform private data if platform doesn't have them. So, if renesas_usbhs was compiled as module, it will be hung-up on 2nd insmod. This patch fixup it. Special thanks to Bastian Reported-by: Bastian Hecht <hechtb@googlemail.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: add mod_host supportKuninori Morimoto5-2/+1349
This is mod_host prototype support for renesas_usbhs driver. It doesn't support USB-Hub, and USB-DMAC for now. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: usbhs_dcp_control_transfer_done() cares mod_hostKuninori Morimoto1-1/+5
CCPL setting is needed on only mod_gadget. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: add data/status stage handlerKuninori Morimoto2-0/+150
mod_host needs data/status stage handler Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: add INTSTS1 interrupt supportKuninori Morimoto3-6/+75
mod_host use INTSTS1 interrupt Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: add usbhs_set_device_speed() support for hostKuninori Morimoto2-0/+67
mod_host needs device speed setup function Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: make sure SOF packet sending-out controlKuninori Morimoto1-0/+7
It is enabled to set SOF packet output bit when USBRST bit was set. And USBRST bit should be set 0 when SOF packet was output. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: support otg pin controlKuninori Morimoto3-0/+10
some renesas_usbhs device is supporting OTG external device interface. In that device, it is necessary to control PWEN/EXTLP on DVSTCTR. This patch support it. But renesas_usbhs driver doesn't have OTG support for now. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: disable pipe on top of interruptKuninori Morimoto1-9/+14
When data read interrupt happened, the pipe is BUF which means "enable". then, next un-necessary interrupt/token might be issued again when all data were popped from fifo. It will cause un-understandable bug. This patch decides pipe disable on top of read interrupt. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: modify pipe sequence settingsKuninori Morimoto4-7/+14
renesas_usbhs can manually set DATA0/DATA1. This patch is prepare for mod_host support Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: disable auto paket start on usbhs_pkt_push()Kuninori Morimoto2-2/+1
Automatically packet start by usbhs_pkt_push() was useful. But the pushed packet will be called twice if new packet was pushed on usbhs_pkt :: done callback. (1st is called by usbhs_pkt_push(), 2nd is called by usbhsf_pkt_handler()) This patch disables automatic packet start, and clarified packet start timing. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: move done callback to struct usbhs_pktKuninori Morimoto5-33/+32
transfer done function was registered in struct struct usbhs_pipe_info. It was good for mod_gadget, but not good for mod_host. This function move it to struct usbhs_pkt. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: add usbhs_pipe_name()Kuninori Morimoto2-1/+7
pipe name is usefull function for mod_xxx Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: add device select support in ↵Kuninori Morimoto3-5/+18
usbhs_pipe_config_update() device select method will be used on mod_host Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: add struct usbhs_priv to packet done functionKuninori Morimoto4-5/+7
There was no method to get struct usbhs_priv when packet transfer done function was called. This patch allow that callback function receive it. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: add usbhs_dcp_dir_for_host()Kuninori Morimoto3-1/+12
renesas_usbhs device needs special bit settings if it was mod_host and dcp pipe. This patch support it. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: remove unneeded parameter from usbhs_mod_is_host()Kuninori Morimoto3-4/+4
it was possible to get usbhs_mod from usbhs_priv. this patch remove unneeded parameter. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: move usbhs_usbreq_get/set_val() to common.cKuninori Morimoto4-30/+33
usbhs_usbreq_get/set_val() functions were in pipe.c file, but it is irrelevant to pipe. this patch move it to common.c Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: move usbhsp_type() to usbhs_pipe_type()Kuninori Morimoto2-18/+20
Pipe type check macro will be used in other files. This patch move local macro to global macro. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: add usbhs_bus_get_speed()Kuninori Morimoto5-19/+18
current mod_gadget had got usb speed on usbhsg_irq_dev_state() which is status change interrupt callback function. And the usb speed data was included in its parameter. But this style works for mod_gadget, but doesn't work for mod_host which isn't interrupted when device status was changed. This patch add usbhs_bus_get_speed() to solve this issue. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: add bus control functionsKuninori Morimoto3-1/+50
this patch add DVSTCTR control function for HOST support Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: change usbhsc_bus_ctrl() to usbsc_set_buswait()Kuninori Morimoto2-10/+7
renesas_usbhs will have register DVSTCTR control function for HOST support. This patch changes usbhsc_bus_ctrl() to usbsc_set_buswait(), to remove DVSTCTR access from it, Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: tidyup INTENB0 methodKuninori Morimoto1-1/+10
This patch tidyup Interrupt Enable Register 0 (INTENB0) which has relationship with picky BEMPENB/BRDYENB. - add explain comment - ignore nonsense 0 write case Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: struct usbhs_pipe hold handlerKuninori Morimoto4-13/+16
packet handler had moved to struct usbhs_pipe from struct usbhsg_uep. it is preparation of mod_host support Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: each pipe hold maxpacket sizeKuninori Morimoto2-21/+10
Current renesas_usbhs pipe accessed DCPMAXP/PIPEMAXP register to get own maxpacket size every time. But maxpacket size isn't changed after pipe start, and register access is too slow. This patch adds new maxp variable to keep own maxpacket. And un-used function are removed. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: remove desc from usbhs_pipe_mallocKuninori Morimoto3-38/+45
Current usbhs_pipe_malloc() used usb_endpoint_descriptor to get necessary information. It was very good for mod_gadget which allocate pipe in runtime, but is not good for mod_host which allocate pipe in initial timing. This patch remove usb_endpoint_descriptor from usbhs_pipe_malloc() Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: move USBHSF_PKT_xxx to pipe.cKuninori Morimoto2-15/+16
There is no longer necessity that USBHSF_PKT_xxx are in fifo.h. it are used in only fifo.c now. This patch move it. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13usb: gadget: renesas_usbhs: add suspend/resume supportKuninori Morimoto1-5/+64
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-23 21:41:22 +0300