summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2010-04-16ath9k_htc: Fix sparse endian warningsSujith9-52/+51
This patch fixes a bunch of endian issues that were exposed by sparse. It's a miracle that the driver worked at all till now. The Lord be praised. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_htc: Handle WMI timeouts properlySujith2-0/+14
If a WMI command has timed out for some reason, a late WMI response would end up updating the response region of a new WMI request that has been issued in the meantime. Fix this race condition by dropping a WMI response if a new WMI command has been issued. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_htc: Add dropped SKB count to debugfsSujith3-4/+13
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_htc: Remove GPIO set on unloadSujith1-1/+0
There is no point in trying to set the LED pin when the module is being unloaded. The target would be reset anyway. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Use buffered register writesSujith8-1/+175
This patch adds macros at certain places which could be optimized for multiple register writes. The performance of ath9k_htc improves considerably, especially reducing the latency involved in a scan run. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Relocate Opmode initializationSujith1-6/+2
Programming the opmode in the HW can be done before the assoc_id and STA_ID registers are setup. This helps ath9k_htc when multiple register writes are used. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Add macros for multiple register writesSujith1-0/+18
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_htc: Implement multiple register write supportSujith3-4/+113
This patch adds support for writing multiple registers in a single USB command. Specific calls from the HW code that performs multiple register writes would be modified to make use of this in subsequent patches. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath: Add buffered register write operationsSujith1-1/+13
This is required to implement delayed/buffered register writes in ath9k_htc. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_htc: Cleanup beacon configurationSujith2-15/+10
This patch cleans up beacon configuration, removing a redundant interface type check and updating beacon interval in the correct place. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16iwmc3200wifi: check sparse endianness annotationsSamuel Ortiz1-0/+2
Add -D__CHECK_ENDIAN__ to driver ccflags so that sparse will always check endianness by default. Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16iwmc3200wifi: Fix sparse warningsSamuel Ortiz3-5/+6
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath5k/ath9k: Fix 64 bits TSF readsBenoit Papillault2-6/+44
According to tests, both TSF lower and upper registers kept counting, so the higher part could have been updated after the lower part has been read, as shown in the following log where the upper part is read first and the lower part next. tsf = {00000003-fffffffd} tsf = {00000003-00000001} tsf = {00000004-0000000b} This patch corrects this by checking that the upper part has not been changed while the lower part was read. It has been tested in an IBSS network where artifical IBSS merges have been done in order to trigger hundreds of rollover for the TSF lower part. It follows the logic mentionned by Derek, with only 2 register reads needed at each additional steps instead of 3 (the minimum number of register reads is still 3). Signed-off-by: Benoit Papillault <benoit.papillault@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: add the PCI ID for the first AR9300 deviceLuis R. Rodriguez1-0/+1
The first AR9003 hardware family device supported is the AR9300, which has the vendor:device id 168c:0030 Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Abort rx if hw is not coming out of full sleep in resetVasanthakumar Thiagarajan3-0/+16
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k: Enable TXOK and TXERR interrupts for TX EDMAVasanthakumar Thiagarajan1-5/+10
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k: add LDPC supportLuis R. Rodriguez3-4/+22
LDPC is enabled by the rate control if the its determined that the target peer supports LDPC. We would have already intersected the HT capabilities so if our peer supports LDPC so do we. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: add LDPC support for AR9003Luis R. Rodriguez4-2/+6
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16mac80211: add LDPC control flagLuis R. Rodriguez1-0/+2
LDPC will be enabled through the rate control algorithm for each buffer the the tx_info flags. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k: Add Tx EDMA supportVasanthakumar Thiagarajan3-60/+218
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Compute pointer checksum over the link descriptorVasanthakumar Thiagarajan1-15/+21
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k: Initialize and configure tx status for EDMAVasanthakumar Thiagarajan4-2/+52
Also add a function to clean up tx status ring. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k: Setup appropriate tx desc for regular dma and edmaVasanthakumar Thiagarajan4-14/+20
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: set cwmin and cwmax to 0 for for AR9003 upon txq resetLuis R. Rodriguez1-0/+6
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: enable CRC check of descriptors for AR9003Luis R. Rodriguez2-0/+7
Enable CRC check on the descriptor fetched from host on AR9003 upon reseting the TX queue. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k: add RXLP and RXHP to debugfs countersLuis R. Rodriguez2-4/+22
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Fill descriptor abstrations for AR9003Vasanthakumar Thiagarajan3-7/+254
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: move AR9002 mac ops to its own fileLuis R. Rodriguez10-464/+486
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Add function to configure tx status ring bufferVasanthakumar Thiagarajan5-1/+59
Also reset tx status ring suring chip reset. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Define abstraction for tx desc accessVasanthakumar Thiagarajan7-281/+431
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k: Load SW filtered NF values and start NF cal during full reset for AR9003Vasanthakumar Thiagarajan1-0/+5
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: skip WEP aggregation enable code for AR9003Luis R. Rodriguez3-5/+15
The AR9002 hardware code enables aggregation for WEP but mac80211 doesn't enable aggregation with WEP, and the AR9003 code family does not need this so skip it for now for AR9003 but leave the code and annotate we should eventually consider how to remove this in consideration for the HAL unification goals. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: skip asynch fifo enablement to AR9003Luis R. Rodriguez3-15/+32
The asynch fifo code is specific to >= AR9287 so stuff it into the AR9002 hardware family code and skip it for AR9003 cards. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Update ath9k_hw_set_dma for AR9300Felix Fietkau2-3/+21
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: add TX/RX gain register initialization for AR9003Luis R. Rodriguez3-0/+69
This is done depending on what the EEPROM settings indicates. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: add the AR9300 SREV hw name printLuis R. Rodriguez1-0/+1
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Configure Tx interrupt mitigation timerVasanthakumar Thiagarajan1-0/+5
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: move the RF claim stuff to AR9002 hardware familyLuis R. Rodriguez3-46/+53
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: move AR9280 PCI EEPROM fix to eeprom_def.cFelix Fietkau2-17/+6
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Fill get_isr() for AR9003Vasanthakumar Thiagarajan5-0/+146
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: add OFDM spur mitigation for AR9003Luis R. Rodriguez5-4/+267
We add this now as OFDM spur mitigation required accessing the EEPROM for the AR9003 devices. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Implement AR9003 eeprom callbacksSenthil Balasubramanian7-4/+2187
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: restore mac address reading logicLuis R. Rodriguez5-11/+11
Once upon a time the AR_EEPROM_MAC macro was added to let us add a random attribute to the three 4-bytes of MAC addresses entries we read from the EEPROM. This was good while a random high-enough value was used which did not conflict with any of the already existing enum eeprom_param values. With AR9003 support the enums overlap and it means we either increment the random offset or just restore the reading logic to match what the HAL has. I choose to do the later to synchronize the logic on both code bases. This should fix reading the MAC address from the EEPROM on AR9003 hardware. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: rename eep_AR9287_ops to eep_ar9287_opsLuis R. Rodriguez3-3/+3
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: complete AR9003 calibrationLuis R. Rodriguez4-12/+667
This goes with some new shiny TX IQ calibration that AR9003 hardware family supports. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: fill in the callbacks for calibration for AR9003Luis R. Rodriguez3-2/+39
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: abstract loading noisefloorLuis R. Rodriguez6-68/+81
This is the last call on calib.c which acceses PHY stuff, with this change we calib.c is now generic between both all supported hardware families. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: abstract the AR_PHY_AGC_CONTROL register accessLuis R. Rodriguez3-20/+15
This is so we can share routines which access this register on calib.c Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Initialize interrupt mask for AR9003Vasanthakumar Thiagarajan2-5/+29
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Abstract the routine which returns interrupt statusVasanthakumar Thiagarajan7-286/+310
Also move interrupt related code to mac.c Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-01-18 03:46:30 +0300