| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 330bb7117101099c687e9c7f13d48068670b9c62 upstream.
In commit 38506ecefab9 ("rtlwifi: rtl_pci: Start modification for
new drivers"), the flag that indicates that interrupts are enabled was
never set.
In addition, there are several places when enable/disable interrupts
were commented out are restored. A sychronize_interrupts() call is
removed.
Fixes: 38506ecefab9 ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # v3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3155db7613edea8fb943624062baf1e4f9cfbfd6 upstream.
In commit 38506ecefab9 ("rtlwifi: rtl_pci: Start modification for
new drivers"), a callback needed to check if the hardware has released
a buffer indicating that a DMA operation is completed was not added.
Fixes: 38506ecefab9 ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # v3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0e531cc575c4e9e3dd52ad287b49d3c2dc74c810 upstream.
In commit 38506ecefab9 ("rtlwifi: rtl_pci: Start modification for
new drivers"), a callback to get the RX buffer address was added to
the PCI driver. Unfortunately, driver rtl8192de was not modified
appropriately and the code runs into a WARN_ONCE() call. The use
of an incorrect array is also fixed.
Fixes: 38506ecefab9 ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # 3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3e1740993e43116b3bc71b0aad1e6872f6ccf341 upstream.
Testing with the new fsstress support for subvolumes uncovered a pretty
bad problem with rename exchange on subvolumes. We're modifying two
different subvolumes, but we only start the transaction on one of them,
so the other one is not added to the dirty root list. This is caught by
btrfs_cow_block() with a warning because the root has not been updated,
however if we do not modify this root again we'll end up pointing at an
invalid root because the root item is never updated.
Fix this by making sure we add the destination root to the trans list,
the same as we do with normal renames. This fixes the corruption.
Fixes: cdd1fedf8261 ("btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT")
CC: stable@vger.kernel.org # 4.9+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fd0ddbe2509568b00df364156f47561e9f469f15 upstream.
Backreference walking, which is used by send to figure if it can issue
clone operations instead of write operations, can be very slow and use
too much memory when extents have many references. This change simply
skips backreference walking when an extent has more than 64 references,
in which case we fallback to a write operation instead of a clone
operation. This limit is conservative and in practice I observed no
signicant slowdown with up to 100 references and still low memory usage
up to that limit.
This is a temporary workaround until there are speedups in the backref
walking code, and as such it does not attempt to add extra interfaces or
knobs to tweak the threshold.
Reported-by: Atemu <atemu.main@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/CAE4GHgkvqVADtS4AzcQJxo0Q1jKQgKaW3JGp3SGdoinVo=C9eQ@mail.gmail.com/T/#me55dc0987f9cc2acaa54372ce0492c65782be3fa
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34b127aecd4fe8e6a3903e10f204a7b7ffddca22 upstream.
The last user of btrfs_bio::flags was removed in commit 326e1dbb5736
("block: remove management of bi_remaining when restoring original
bi_end_io"), remove it.
(Tagged for stable as the structure is heavily used and space savings
are desirable.)
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f7bddf1e27d18fbc7d3e3056ba449cfbe4e20b0a upstream.
During a cyclic writeback, extent_write_cache_pages() uses done_index
to update the writeback_index after the current run is over. However,
instead of current index + 1, it gets to to the current index itself.
Unfortunately, this, combined with returning on EOF instead of looping
back, can lead to the following pathlogical behavior.
1. There is a single file which has accumulated enough dirty pages to
trigger balance_dirty_pages() and the writer appending to the file
with a series of short writes.
2. balance_dirty_pages kicks in, wakes up background writeback and sleeps.
3. Writeback kicks in and the cursor is on the last page of the dirty
file. Writeback is started or skipped if already in progress. As
it's EOF, extent_write_cache_pages() returns and the cursor is set
to done_index which is pointing to the last page.
4. Writeback is done. Nothing happens till balance_dirty_pages
finishes, at which point we go back to #1.
This can almost completely stall out writing back of the file and keep
the system over dirty threshold for a long time which can mess up the
whole system. We encountered this issue in production with a package
handling application which can reliably reproduce the issue when
running under tight memory limits.
Reading the comment in the error handling section, this seems to be to
avoid accidentally skipping a page in case the write attempt on the
page doesn't succeed. However, this concern seems bogus.
On each page, the code either:
* Skips and moves onto the next page.
* Fails issue and sets done_index to index + 1.
* Successfully issues and continue to the next page if budget allows
and not EOF.
IOW, as long as it's not EOF and there's budget, the code never
retries writing back the same page. Only when a page happens to be
the last page of a particular run, we end up retrying the page, which
can't possibly guarantee anything data integrity related. Besides,
cyclic writes are only used for non-syncing writebacks meaning that
there's no data integrity implication to begin with.
Fix it by always setting done_index past the current page being
processed.
Note that this problem exists in other writepages too.
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
write
commit a0e248bb502d5165b3314ac3819e888fdcdf7d9f upstream.
When doing a buffered write it's possible to leave the subv_writers
counter of the root, used for synchronization between buffered nocow
writers and snapshotting. This happens in an exceptional case like the
following:
1) We fail to allocate data space for the write, since there's not
enough available data space nor enough unallocated space for allocating
a new data block group;
2) Because of that failure, we try to go to NOCOW mode, which succeeds
and therefore we set the local variable 'only_release_metadata' to true
and set the root's sub_writers counter to 1 through the call to
btrfs_start_write_no_snapshotting() made by check_can_nocow();
3) The call to btrfs_copy_from_user() returns zero, which is very unlikely
to happen but not impossible;
4) No pages are copied because btrfs_copy_from_user() returned zero;
5) We call btrfs_end_write_no_snapshotting() which decrements the root's
subv_writers counter to 0;
6) We don't set 'only_release_metadata' back to 'false' because we do
it only if 'copied', the value returned by btrfs_copy_from_user(), is
greater than zero;
7) On the next iteration of the while loop, which processes the same
page range, we are now able to allocate data space for the write (we
got enough data space released in the meanwhile);
8) After this if we fail at btrfs_delalloc_reserve_metadata(), because
now there isn't enough free metadata space, or in some other place
further below (prepare_pages(), lock_and_cleanup_extent_if_need(),
btrfs_dirty_pages()), we break out of the while loop with
'only_release_metadata' having a value of 'true';
9) Because 'only_release_metadata' is 'true' we end up decrementing the
root's subv_writers counter to -1 (through a call to
btrfs_end_write_no_snapshotting()), and we also end up not releasing the
data space previously reserved through btrfs_check_data_free_space().
As a consequence the mechanism for synchronizing NOCOW buffered writes
with snapshotting gets broken.
Fix this by always setting 'only_release_metadata' to false at the start
of each iteration.
Fixes: 8257b2dc3c1a ("Btrfs: introduce btrfs_{start, end}_nocow_write() for each subvolume")
Fixes: 7ee9e4405f26 ("Btrfs: check if we can nocow if we don't have data space")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 536870071dbc4278264f59c9a2f5f447e584d139 upstream.
In the fixup worker, if we fail to mark the range as delalloc in the io
tree, we must release the previously reserved metadata, as well as update
the outstanding extents counter for the inode, otherwise we leak metadata
space.
In pratice we can't return an error from btrfs_set_extent_delalloc(),
which is just a wrapper around __set_extent_bit(), as for most errors
__set_extent_bit() does a BUG_ON() (or panics which hits a BUG_ON() as
well) and returning an -EEXIST error doesn't happen in this case since
the exclusive bits parameter always has a value of 0 through this code
path. Nevertheless, just fix the error handling in the fixup worker,
in case one day __set_extent_bit() can return an error to this code
path.
Fixes: f3038ee3a3f101 ("btrfs: Handle btrfs_set_extent_delalloc failure in fixup worker")
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit baf320b9d531f1cfbf64c60dd155ff80a58b3796 upstream.
We hit the following warning while running down a different problem
[ 6197.175850] ------------[ cut here ]------------
[ 6197.185082] refcount_t: underflow; use-after-free.
[ 6197.194704] WARNING: CPU: 47 PID: 966 at lib/refcount.c:190 refcount_sub_and_test_checked+0x53/0x60
[ 6197.521792] Call Trace:
[ 6197.526687] __btrfs_release_delayed_node+0x76/0x1c0
[ 6197.536615] btrfs_kill_all_delayed_nodes+0xec/0x130
[ 6197.546532] ? __btrfs_btree_balance_dirty+0x60/0x60
[ 6197.556482] btrfs_clean_one_deleted_snapshot+0x71/0xd0
[ 6197.566910] cleaner_kthread+0xfa/0x120
[ 6197.574573] kthread+0x111/0x130
[ 6197.581022] ? kthread_create_on_node+0x60/0x60
[ 6197.590086] ret_from_fork+0x1f/0x30
[ 6197.597228] ---[ end trace 424bb7ae00509f56 ]---
This is because the free side drops the ref without the lock, and then
takes the lock if our refcount is 0. So you can have nodes on the tree
that have a refcount of 0. Fix this by zero'ing out that element in our
temporary array so we don't try to kill it again.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add comment ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3797136b626ad4b6582223660c041efdea8f26b2 upstream.
While testing 5.2 we ran into the following panic
[52238.017028] BUG: kernel NULL pointer dereference, address: 0000000000000001
[52238.105608] RIP: 0010:drop_buffers+0x3d/0x150
[52238.304051] Call Trace:
[52238.308958] try_to_free_buffers+0x15b/0x1b0
[52238.317503] shrink_page_list+0x1164/0x1780
[52238.325877] shrink_inactive_list+0x18f/0x3b0
[52238.334596] shrink_node_memcg+0x23e/0x7d0
[52238.342790] ? do_shrink_slab+0x4f/0x290
[52238.350648] shrink_node+0xce/0x4a0
[52238.357628] balance_pgdat+0x2c7/0x510
[52238.365135] kswapd+0x216/0x3e0
[52238.371425] ? wait_woken+0x80/0x80
[52238.378412] ? balance_pgdat+0x510/0x510
[52238.386265] kthread+0x111/0x130
[52238.392727] ? kthread_create_on_node+0x60/0x60
[52238.401782] ret_from_fork+0x1f/0x30
The page we were trying to drop had a page->private, but had no
page->mapping and so called drop_buffers, assuming that we had a
buffer_head on the page, and then panic'ed trying to deref 1, which is
our page->private for data pages.
This is happening because we're truncating the free space cache while
we're trying to load the free space cache. This isn't supposed to
happen, and I'll fix that in a followup patch. However we still
shouldn't allow those sort of mistakes to result in messing with pages
that do not belong to us. So add the page->mapping check to verify that
we still own this page after dropping and re-acquiring the page lock.
This page being unlocked as:
btrfs_readpage
extent_read_full_page
__extent_read_full_page
__do_readpage
if (!nr)
unlock_page <-- nr can be 0 only if submit_extent_page
returns an error
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
[ add callchain ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f4925a7b23428d5719af5a2816586b2a0e6fd19 upstream.
When the implementation of SKBs with fraglist was sent upstream, a
merge-damage occurred and half the patch was not applied.
This causes problems in high-throughput situations with AX200 devices,
including low throughput and FW crashes.
Introduce the part that was missing from the original patch.
Fixes: 0044f1716c4d ("iwlwifi: pcie: support transmitting SKBs with fraglist")
Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[ This patch was created by me, but the original author of this code
is Johannes, so his s-o-b is here and he's marked as the author of
the patch. ]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c388abefda0d92355714010c0199055c57ab6c7 upstream.
We can't use "port->sw" and/or "port->mux" after it has been freed.
Fixes: 23481121c81d ("usb: typec: class: Don't use port parent for getting mux handles")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: stable <stable@vger.kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191126140452.14048-1-wenyang@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4bd5ead82d4b877ebe41daf95f28cda53205b039 upstream.
Since the role_store() uses strncmp(), it's possible to refer
out-of-memory if the sysfs data size is smaller than strlen("host").
This patch fixes it by using sysfs_streq() instead of strncmp().
Reported-by: Pavel Machek <pavel@denx.de>
Fixes: 9bb86777fb71 ("phy: rcar-gen3-usb2: add sysfs for usb role swap")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2d7b78f59e020b07fc6338eefe286f54ee2d6773 upstream.
Clear ep0's DWC3_EP_TRANSFER_STARTED flag if the END_TRANSFER command is
completed. Otherwise, we can't start control transfer again after
END_TRANSFER.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3abda5a98a18e524e17fd4085c9f4bd53e9ef53 upstream.
Normally the END_TRANSFER command completion handler will clear the
DWC3_EP_TRANSFER_STARTED flag. However, if the command was sent without
interrupt on completion, then the flag will not be cleared. Make sure to
clear the flag in this case.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c7d4b7b3d43c54c0b8c1e4adb917a151c754196 upstream.
This patch corrects the condition to kick the transfer without
giving back the requests when either request has remaining data
or when there are pending SGs. The && check was introduced during
spliting up the dwc3_gadget_ep_cleanup_completed_requests() function.
Fixes: f38e35dd84e2 ("usb: dwc3: gadget: split dwc3_gadget_ep_cleanup_completed_requests()")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c3caae4cd6e122472efcf64759ff6392fb6bce2 upstream.
The original ID that was added for Comet Lake PCH was
actually for the -LP (low power) variant even though the
constant for it said CMLH. Changing that while at it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191212093713.60614-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63341ab03706e11a31e3dd8ccc0fbc9beaf723f0 upstream.
In case we have to migrate a ballon page to a newpage of another zone, the
managed page count of both zones is wrong. Paired with memory offlining
(which will adjust the managed page count), we can trigger kernel crashes
and all kinds of different symptoms.
One way to reproduce:
1. Start a QEMU guest with 4GB, no NUMA
2. Hotplug a 1GB DIMM and online the memory to ZONE_NORMAL
3. Inflate the balloon to 1GB
4. Unplug the DIMM (be quick, otherwise unmovable data ends up on it)
5. Observe /proc/zoneinfo
Node 0, zone Normal
pages free 16810
min 24848885473806
low 18471592959183339
high 36918337032892872
spanned 262144
present 262144
managed 18446744073709533486
6. Do anything that requires some memory (e.g., inflate the balloon some
more). The OOM goes crazy and the system crashes
[ 238.324946] Out of memory: Killed process 537 (login) total-vm:27584kB, anon-rss:860kB, file-rss:0kB, shmem-rss:00
[ 238.338585] systemd invoked oom-killer: gfp_mask=0x100cca(GFP_HIGHUSER_MOVABLE), order=0, oom_score_adj=0
[ 238.339420] CPU: 0 PID: 1 Comm: systemd Tainted: G D W 5.4.0-next-20191204+ #75
[ 238.340139] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu4
[ 238.341121] Call Trace:
[ 238.341337] dump_stack+0x8f/0xd0
[ 238.341630] dump_header+0x61/0x5ea
[ 238.341942] oom_kill_process.cold+0xb/0x10
[ 238.342299] out_of_memory+0x24d/0x5a0
[ 238.342625] __alloc_pages_slowpath+0xd12/0x1020
[ 238.343024] __alloc_pages_nodemask+0x391/0x410
[ 238.343407] pagecache_get_page+0xc3/0x3a0
[ 238.343757] filemap_fault+0x804/0xc30
[ 238.344083] ? ext4_filemap_fault+0x28/0x42
[ 238.344444] ext4_filemap_fault+0x30/0x42
[ 238.344789] __do_fault+0x37/0x1a0
[ 238.345087] __handle_mm_fault+0x104d/0x1ab0
[ 238.345450] handle_mm_fault+0x169/0x360
[ 238.345790] do_user_addr_fault+0x20d/0x490
[ 238.346154] do_page_fault+0x31/0x210
[ 238.346468] async_page_fault+0x43/0x50
[ 238.346797] RIP: 0033:0x7f47eba4197e
[ 238.347110] Code: Bad RIP value.
[ 238.347387] RSP: 002b:00007ffd7c0c1890 EFLAGS: 00010293
[ 238.347834] RAX: 0000000000000002 RBX: 000055d196a20a20 RCX: 00007f47eba4197e
[ 238.348437] RDX: 0000000000000033 RSI: 00007ffd7c0c18c0 RDI: 0000000000000004
[ 238.349047] RBP: 00007ffd7c0c1c20 R08: 0000000000000000 R09: 0000000000000033
[ 238.349660] R10: 00000000ffffffff R11: 0000000000000293 R12: 0000000000000001
[ 238.350261] R13: ffffffffffffffff R14: 0000000000000000 R15: 00007ffd7c0c18c0
[ 238.350878] Mem-Info:
[ 238.351085] active_anon:3121 inactive_anon:51 isolated_anon:0
[ 238.351085] active_file:12 inactive_file:7 isolated_file:0
[ 238.351085] unevictable:0 dirty:0 writeback:0 unstable:0
[ 238.351085] slab_reclaimable:5565 slab_unreclaimable:10170
[ 238.351085] mapped:3 shmem:111 pagetables:155 bounce:0
[ 238.351085] free:720717 free_pcp:2 free_cma:0
[ 238.353757] Node 0 active_anon:12484kB inactive_anon:204kB active_file:48kB inactive_file:28kB unevictable:0kB iss
[ 238.355979] Node 0 DMA free:11556kB min:36kB low:48kB high:60kB reserved_highatomic:0KB active_anon:152kB inactivB
[ 238.358345] lowmem_reserve[]: 0 2955 2884 2884 2884
[ 238.358761] Node 0 DMA32 free:2677864kB min:7004kB low:10028kB high:13052kB reserved_highatomic:0KB active_anon:0B
[ 238.361202] lowmem_reserve[]: 0 0 72057594037927865 72057594037927865 72057594037927865
[ 238.361888] Node 0 Normal free:193448kB min:99395541895224kB low:73886371836733356kB high:147673348131571488kB reB
[ 238.364765] lowmem_reserve[]: 0 0 0 0 0
[ 238.365101] Node 0 DMA: 7*4kB (U) 5*8kB (UE) 6*16kB (UME) 2*32kB (UM) 1*64kB (U) 2*128kB (UE) 3*256kB (UME) 2*512B
[ 238.366379] Node 0 DMA32: 0*4kB 1*8kB (U) 2*16kB (UM) 2*32kB (UM) 2*64kB (UM) 1*128kB (U) 1*256kB (U) 1*512kB (U)B
[ 238.367654] Node 0 Normal: 1985*4kB (UME) 1321*8kB (UME) 844*16kB (UME) 524*32kB (UME) 300*64kB (UME) 138*128kB (B
[ 238.369184] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=2048kB
[ 238.369915] 130 total pagecache pages
[ 238.370241] 0 pages in swap cache
[ 238.370533] Swap cache stats: add 0, delete 0, find 0/0
[ 238.370981] Free swap = 0kB
[ 238.371239] Total swap = 0kB
[ 238.371488] 1048445 pages RAM
[ 238.371756] 0 pages HighMem/MovableOnly
[ 238.372090] 306992 pages reserved
[ 238.372376] 0 pages cma reserved
[ 238.372661] 0 pages hwpoisoned
In another instance (older kernel), I was able to observe this
(negative page count :/):
[ 180.896971] Offlined Pages 32768
[ 182.667462] Offlined Pages 32768
[ 184.408117] Offlined Pages 32768
[ 186.026321] Offlined Pages 32768
[ 187.684861] Offlined Pages 32768
[ 189.227013] Offlined Pages 32768
[ 190.830303] Offlined Pages 32768
[ 190.833071] Built 1 zonelists, mobility grouping on. Total pages: -36920272750453009
In another instance (older kernel), I was no longer able to start any
process:
[root@vm ~]# [ 214.348068] Offlined Pages 32768
[ 215.973009] Offlined Pages 32768
cat /proc/meminfo
-bash: fork: Cannot allocate memory
[root@vm ~]# cat /proc/meminfo
-bash: fork: Cannot allocate memory
Fix it by properly adjusting the managed page count when migrating if
the zone changed. The managed page count of the zones now looks after
unplug of the DIMM (and after deflating the balloon) just like before
inflating the balloon (and plugging+onlining the DIMM).
We'll temporarily modify the totalram page count. If this ever becomes a
problem, we can fine tune by providing helpers that don't touch
the totalram pages (e.g., adjust_zone_managed_page_count()).
Please note that fixing up the managed page count is only necessary when
we adjusted the managed page count when inflating - only if we
don't have VIRTIO_BALLOON_F_DEFLATE_ON_OOM. With that feature, the
managed page count is not touched when inflating/deflating.
Reported-by: Yumei Huang <yuhuang@redhat.com>
Fixes: 3dcc0571cd64 ("mm: correctly update zone->managed_pages")
Cc: <stable@vger.kernel.org> # v3.11+
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc71d8b580ba81b55b6e15b1c0320632515b4bac upstream.
When virt_wifi interface is created, virt_wifi_newlink() is called and
it calls register_netdevice().
if register_netdevice() fails, it internally would call
->priv_destructor(), which is virt_wifi_net_device_destructor() and
it frees netdev. but virt_wifi_newlink() still use netdev.
So, use-after-free would occur in virt_wifi_newlink().
Test commands:
ip link add dummy0 type dummy
modprobe bonding
ip link add bonding_masters link dummy0 type virt_wifi
Splat looks like:
[ 202.220554] BUG: KASAN: use-after-free in virt_wifi_newlink+0x88b/0x9a0 [virt_wifi]
[ 202.221659] Read of size 8 at addr ffff888061629cb8 by task ip/852
[ 202.222896] CPU: 1 PID: 852 Comm: ip Not tainted 5.4.0-rc5 #3
[ 202.223765] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 202.225073] Call Trace:
[ 202.225532] dump_stack+0x7c/0xbb
[ 202.226869] print_address_description.constprop.5+0x1be/0x360
[ 202.229362] __kasan_report+0x12a/0x16f
[ 202.230714] kasan_report+0xe/0x20
[ 202.232595] virt_wifi_newlink+0x88b/0x9a0 [virt_wifi]
[ 202.233370] __rtnl_newlink+0xb9f/0x11b0
[ 202.244909] rtnl_newlink+0x65/0x90
[ ... ]
Cc: stable@vger.kernel.org
Fixes: c7cdba31ed8b ("mac80211-next: rtnetlink wifi simulation device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20191121122645.9355-1-ap420073@gmail.com
[trim stack dump a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a3c4c2339f8948b0f578e938970303a7372e60c0 upstream.
Change calculating of position page containing BBM
If none of BBM flags are set then function nand_bbm_get_next_page
reports EINVAL. It causes that BBM is not read at all during scanning
factory bad blocks. The result is that the BBT table is build without
checking factory BBM at all. For Micron flash memories none of these
flags are set if page size is different than 2048 bytes.
Address this regression by:
- adding NAND_BBM_FIRSTPAGE chip flag without any condition. It solves
issue only for Micron devices.
- changing the nand_bbm_get_next_page_function. It will return 0
if no of BBM flag is set and page parameter is 0. After that modification
way of discovering factory bad blocks will work similar as in kernel
version 5.1.
Cc: stable@vger.kernel.org
Fixes: f90da7818b14 (mtd: rawnand: Support bad block markers in first, second or last page)
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 69c7f4618c16b4678f8a4949b6bb5ace259c0033 upstream.
Any write with either dd or flashcp to a device driven by the
spear_smi.c driver will pass through the spear_smi_cpy_toio()
function. This function will get called for chunks of up to 256 bytes.
If the amount of data is smaller, we may have a problem if the data
length is not 4-byte aligned. In this situation, the kernel panics
during the memcpy:
# dd if=/dev/urandom bs=1001 count=1 of=/dev/mtd6
spear_smi_cpy_toio [620] dest c9070000, src c7be8800, len 256
spear_smi_cpy_toio [620] dest c9070100, src c7be8900, len 256
spear_smi_cpy_toio [620] dest c9070200, src c7be8a00, len 256
spear_smi_cpy_toio [620] dest c9070300, src c7be8b00, len 233
Unhandled fault: external abort on non-linefetch (0x808) at 0xc90703e8
[...]
PC is at memcpy+0xcc/0x330
The above error occurs because the implementation of memcpy_toio()
tries to optimize the number of I/O by writing 4 bytes at a time as
much as possible, until there are less than 4 bytes left and then
switches to word or byte writes.
Unfortunately, the specification states about the Write Burst mode:
"the next AHB Write request should point to the next
incremented address and should have the same size (byte,
half-word or word)"
This means ARM architecture implementation of memcpy_toio() cannot
reliably be used blindly here. Workaround this situation by update the
write path to stick to byte access when the burst length is not
multiple of 4.
Fixes: f18dbbb1bfe0 ("mtd: ST SPEAr: Add SMI driver for serial NOR flash")
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d26a6a6150c486f51ea2aaab33af04db02f63b8 upstream.
Keeping interrupts on could result in brcmfmac freeing some resources
and then IRQ handlers trying to use them. That was obviously a straight
path for crashing a kernel.
Example:
CPU0 CPU1
---- ----
brcmf_pcie_reset
brcmf_pcie_bus_console_read
brcmf_detach
...
brcmf_fweh_detach
brcmf_proto_detach
brcmf_pcie_isr_thread
...
brcmf_proto_msgbuf_rx_trigger
...
drvr->proto->pd
brcmf_pcie_release_irq
[ 363.789218] Unable to handle kernel NULL pointer dereference at virtual address 00000038
[ 363.797339] pgd = c0004000
[ 363.800050] [00000038] *pgd=00000000
[ 363.803635] Internal error: Oops: 17 [#1] SMP ARM
(...)
[ 364.029209] Backtrace:
[ 364.031725] [<bf243838>] (brcmf_proto_msgbuf_rx_trigger [brcmfmac]) from [<bf2471dc>] (brcmf_pcie_isr_thread+0x228/0x274 [brcmfmac])
[ 364.043662] r7:00000001 r6:c8ca0000 r5:00010000 r4:c7b4f800
Fixes: 4684997d9eea ("brcmfmac: reset PCIe bus on a firmware crash")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 56d9e7bd3fa0f105b6670021d167744bc50ae4fe upstream.
When an IRQ occurs, regmap_{read,write,...}() is invoked in atomic
context. Regmap must indicate register IO is fast so that a spinlock is
used instead of a mutex to avoid sleeping in atomic context:
lock_acquire
__mutex_lock
mutex_lock_nested
regmap_lock_mutex
regmap_write
a10_eccmgr_irq_unmask
unmask_irq.part.0
irq_enable
__irq_startup
irq_startup
__setup_irq
request_threaded_irq
devm_request_threaded_irq
altr_sdram_probe
Mark it so.
[ bp: Massage. ]
Fixes: 3dab6bd52687 ("EDAC, altera: Add support for Stratix10 SDRAM EDAC")
Reported-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Robert Richter <rrichter@marvell.com>
Cc: stable <stable@vger.kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/1574361048-17572-2-git-send-email-thor.thayer@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1689114acc5e89a196fec6d732dae3e48edb6ad upstream.
devm_kcalloc() can fail and return NULL so we need to check for that.
Cc: stable@vger.kernel.org
Fixes: 58472f5cd4f6f ("tpm: validate TPM 2.0 commands")
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 19e6317d24c25ee737c65d1ffb7483bdda4bb54a upstream.
The problem arises because our read() function grabs a lock of the
circular buffer, finds something of interest, then invokes copy_to_user()
straight from the buffer, which in turn takes mm->mmap_sem. In the same
time, the callback mon_bin_vma_fault() is invoked under mm->mmap_sem.
It attempts to take the fetch lock and deadlocks.
This patch does away with protecting of our page list with any
semaphores, and instead relies on the kernel not close the device
while mmap is active in a process.
In addition, we prohibit re-sizing of a buffer while mmap is active.
This way, when (now unlocked) fault is processed, it works with the
page that is intended to be mapped-in, and not some other random page.
Note that this may have an ABI impact, but hopefully no legitimate
program is this wrong.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Reported-by: syzbot+56f9673bb4cdcbeb0e92@syzkaller.appspotmail.com
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 46eb14a6e158 ("USB: fix usbmon BUG trigger")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191204203941.3503452b@suzdal.zaitcev.lan
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1cd17f7f0def31e3695501c4f86cd3faf8489840 upstream.
Explicitly initialize URB structure urb_list field in usb_init_urb().
This field can be potentially accessed uninitialized and its
initialization is coherent with the usage of list_del_init() in
usb_hcd_unlink_urb_from_ep() and usb_giveback_urb_bh() and its
explicit initialization in usb_hcd_submit_urb() error path.
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191127160355.GA27196@ingrassia.epigenesys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c11c4bed02b202e278c0f5c319ae435d7fb9815 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 03270634e242 ("USB: Add ADU support for Ontrak ADU devices")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1848a543191ae32e558bb0a5974ae7c38ebd86fc upstream.
Free the sw structure only after we are done using it.
This patch just moves the put_device() down a bit to avoid the
use after free.
Fixes: 5c54fcac9a9d ("usb: roles: Take care of driver module reference counting")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20191124142236.25671-1-wenyang@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7c5a2df3367a2c4984f1300261345817d95b71f8 upstream.
Make sure to use the current alternate setting when looking up the
endpoints on epic devices to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 6e8cf7751f9f ("USB: add EPIC support to the io_edgeport driver")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 59920635b89d74b9207ea803d5e91498d39e8b69 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09068c1ad53fb077bdac288869dec2435420bdc4 upstream.
Make sure that the interrupt interface has an endpoint before trying to
access its endpoint descriptors to avoid dereferencing a NULL pointer.
The driver binds to the interrupt interface with interface number 0, but
must not assume that this interface or its current alternate setting are
the first entries in the corresponding configuration arrays.
Fixes: b72458a80c75 ("[PATCH] USB: Eagle and ADI 930 usb adsl modem driver")
Cc: stable <stable@vger.kernel.org> # 2.6.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 11d7c8d3b1259c303fb52789febed58f0bc35ad1 upstream.
When the internal reference was selected by a channel it was not enabled.
This patch fixes that and enables it.
Fixes: b3af341bbd96 ("iio: adc: Add ad7124 support")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 341826a065660d1b77d89e6335b6095cd654271c upstream.
When a conversion result is being read from ADC, the driver reads the
number of channels + 1 because it thinks that IIO_CHAN_SOFT_TIMESTAMP
is also a physical channel. This patch fixes this issue.
Fixes: 2985a5d88455 ("staging: iio: adc: ad7606: Move out of staging")
Reported-by: Robert Wörle <rwoerle@mibtec.de>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 53eaa9c27fdc01b4f4d885223e29f97393409e7e upstream.
Temperature should be reported in milli-degrees, not degrees. Fix
scale and offset values to use the correct unit.
This is a fix for an issue that has been present for a long time.
The fixes tag reflects the point at which the code last changed in a
fashion that would make this fix patch no longer apply. Backports
will be necessary to fix those elements that predate that patch.
Fixes: 1615fe41a195 ("iio: imu: mpu6050: Fix FIFO layout for ICM20602")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 342a6928bd5017edbdae376042d8ad6af3d3b943 upstream.
The IIO_HUMIDITYRELATIVE channel was being incorrectly reported back
as percent when it should have been milli percent. This is via an
incorrect scale value being returned to userspace.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49549cb23a2926eba70bb634e361daea0f319794 upstream.
This patch fixes the scales for the gyroscope, accelerometer and
barometer. The pressure scale was just wrong. For the others, the scale
factors were not taking into account that a 32bit word is being read
from the device.
Fixes: 7abad1063deb ("iio: adis16480: Fix scale factors")
Fixes: 82e7a1b25017 ("iio: imu: adis16480: Add support for ADIS1649x family of devices")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4c35b7a51e2f291471f7221d112c6a45c63e83bc upstream.
The driver is defining debugfs entries by calling
`adis16480_debugfs_init()`. However, those entries are attached to the
iio_dev debugfs entry which won't exist if no debugfs_reg_access
callback is provided.
Fixes: 2f3abe6cbb6c ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f9007d692017cef38baf2a9b82b7879d5b2407b upstream.
Since v4.7 the dma initialization requires that there is a
device tree property for "rx" and "tx" channels which is
not provided by the pdata-quirks initialization.
By conversion of the mmc3 setup to device tree this will
finally allows to remove the OpenPandora wlan specific omap3
data-quirks.
Fixes: 81eef6ca9201 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.7+
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b29b8113bb41285eb7ed55ce0c65017b5c0240f7 upstream.
As we will remove items off the list using list_del(), we need to use the
safe version of list_for_each_entry().
Fixes: b5d2f741077a ("interconnect: qcom: Add sdm845 interconnect provider driver")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Cc: <stable@vger.kernel.org> # v5.3+
Link: https://lore.kernel.org/r/20191212075332.16202-3-georgi.djakov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd82873f23c9a6ad834348f8b83f3b6a5bca2c65 upstream.
spin_unlock_irqrestore() might be called with stale flags after
reading port status, possibly restoring interrupts to a incorrect
state.
If a usb2 port just finished resuming while the port status is read
the spin lock will be temporary released and re-acquired in a separate
function. The flags parameter is passed as value instead of a pointer,
not updating flags properly before the final spin_unlock_irqrestore()
is called.
Cc: <stable@vger.kernel.org> # v3.12+
Fixes: 8b3d45705e54 ("usb: Fix xHCI host issues on remote wakeup.")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7ff11162808cc2ec66353fc012c58bb449c892c3 upstream.
xhci driver claims it needs XHCI_TRUST_TX_LENGTH quirk for both
Broadcom/Cavium and a Renesas xHC controllers.
The quirk was inteded for handling false "success" complete event for
transfers that had data left untransferred.
These transfers should complete with "short packet" events instead.
In these two new cases the false "success" completion is reported
after a "short packet" if the TD consists of several TRBs.
xHCI specs 4.10.1.1.2 say remaining TRBs should report "short packet"
as well after the first short packet in a TD, but this issue seems so
common it doesn't make sense to add the quirk for all vendors.
Turn these events into short packets automatically instead.
This gets rid of the "The WARN Successful completion on short TX for
slot 1 ep 1: needs XHCI_TRUST_TX_LENGTH quirk" warning in many cases.
Cc: <stable@vger.kernel.org>
Reported-by: Eli Billauer <eli.billauer@gmail.com>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Eli Billauer <eli.billauer@gmail.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7c67cf6658cec70d8a43229f2ce74ca1443dc95e upstream.
I've recently observed failed xHCI suspend attempt on AMD Raven Ridge
system:
kernel: xhci_hcd 0000:04:00.4: WARN: xHC CMD_RUN timeout
kernel: PM: suspend_common(): xhci_pci_suspend+0x0/0xd0 returns -110
kernel: PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -110
kernel: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x150 returns -110
kernel: PM: Device 0000:04:00.4 failed to suspend async: error -110
Similar to commit ac343366846a ("xhci: Increase STS_SAVE timeout in
xhci_suspend()") we also need to increase the HALT timeout to make it be
able to suspend again.
Cc: <stable@vger.kernel.org> # 5.2+
Fixes: f7fac17ca925 ("xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 057d476fff778f1d3b9f861fdb5437ea1a3cfc99 upstream.
A race in xhci USB3 remote wake handling may force device back to suspend
after it initiated resume siganaling, causing a missed resume event or warm
reset of device.
When a USB3 link completes resume signaling and goes to enabled (UO)
state a interrupt is issued and the interrupt handler will clear the
bus_state->port_remote_wakeup resume flag, allowing bus suspend.
If the USB3 roothub thread just finished reading port status before
the interrupt, finding ports still in suspended (U3) state, but hasn't
yet started suspending the hub, then the xhci interrupt handler will clear
the flag that prevented roothub suspend and allow bus to suspend, forcing
all port links back to suspended (U3) state.
Example case:
usb_runtime_suspend() # because all ports still show suspended U3
usb_suspend_both()
hub_suspend(); # successful as hub->wakeup_bits not set yet
==> INTERRUPT
xhci_irq()
handle_port_status()
clear bus_state->port_remote_wakeup
usb_wakeup_notification()
sets hub->wakeup_bits;
kick_hub_wq()
<== END INTERRUPT
hcd_bus_suspend()
xhci_bus_suspend() # success as port_remote_wakeup bits cleared
Fix this by increasing roothub usage count during port resume to prevent
roothub autosuspend, and by making sure bus_state->port_remote_wakeup
flag is only cleared after resume completion is visible, i.e.
after xhci roothub returned U0 or other non-U3 link state link on a
get port status request.
Issue rootcaused by Chiasheng Lee
Cc: <stable@vger.kernel.org>
Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com>
Reported-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ce91f1a43b37463f517155bdfbd525eb43adbd1a upstream.
When xHCI is part of Alpine or Titan Ridge Thunderbolt controller and
the xHCI device is hot-removed as a result of unplugging a dock for
example, the driver leaks memory it allocates for xhci->usb3_rhub.psi
and xhci->usb2_rhub.psi in xhci_add_in_port() as reported by kmemleak:
unreferenced object 0xffff922c24ef42f0 (size 16):
comm "kworker/u16:2", pid 178, jiffies 4294711640 (age 956.620s)
hex dump (first 16 bytes):
21 00 0c 00 12 00 dc 05 23 00 e0 01 00 00 00 00 !.......#.......
backtrace:
[<000000007ac80914>] xhci_mem_init+0xcf8/0xeb7
[<0000000001b6d775>] xhci_init+0x7c/0x160
[<00000000db443fe3>] xhci_gen_setup+0x214/0x340
[<00000000fdffd320>] xhci_pci_setup+0x48/0x110
[<00000000541e1e03>] usb_add_hcd.cold+0x265/0x747
[<00000000ca47a56b>] usb_hcd_pci_probe+0x219/0x3b4
[<0000000021043861>] xhci_pci_probe+0x24/0x1c0
[<00000000b9231f25>] local_pci_probe+0x3d/0x70
[<000000006385c9d7>] pci_device_probe+0xd0/0x150
[<0000000070241068>] really_probe+0xf5/0x3c0
[<0000000061f35c0a>] driver_probe_device+0x58/0x100
[<000000009da11198>] bus_for_each_drv+0x79/0xc0
[<000000009ce45f69>] __device_attach+0xda/0x160
[<00000000df201aaf>] pci_bus_add_device+0x46/0x70
[<0000000088a1bc48>] pci_bus_add_devices+0x27/0x60
[<00000000ad9ee708>] pci_bus_add_devices+0x52/0x60
unreferenced object 0xffff922c24ef3318 (size 8):
comm "kworker/u16:2", pid 178, jiffies 4294711640 (age 956.620s)
hex dump (first 8 bytes):
34 01 05 00 35 41 0a 00 4...5A..
backtrace:
[<000000007ac80914>] xhci_mem_init+0xcf8/0xeb7
[<0000000001b6d775>] xhci_init+0x7c/0x160
[<00000000db443fe3>] xhci_gen_setup+0x214/0x340
[<00000000fdffd320>] xhci_pci_setup+0x48/0x110
[<00000000541e1e03>] usb_add_hcd.cold+0x265/0x747
[<00000000ca47a56b>] usb_hcd_pci_probe+0x219/0x3b4
[<0000000021043861>] xhci_pci_probe+0x24/0x1c0
[<00000000b9231f25>] local_pci_probe+0x3d/0x70
[<000000006385c9d7>] pci_device_probe+0xd0/0x150
[<0000000070241068>] really_probe+0xf5/0x3c0
[<0000000061f35c0a>] driver_probe_device+0x58/0x100
[<000000009da11198>] bus_for_each_drv+0x79/0xc0
[<000000009ce45f69>] __device_attach+0xda/0x160
[<00000000df201aaf>] pci_bus_add_device+0x46/0x70
[<0000000088a1bc48>] pci_bus_add_devices+0x27/0x60
[<00000000ad9ee708>] pci_bus_add_devices+0x52/0x60
Fix this by calling kfree() for the both psi objects in
xhci_mem_cleanup().
Cc: <stable@vger.kernel.org> # 4.4+
Fixes: 47189098f8be ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f2c710f7dca8457e88b4ac9de2060f011254f9dd upstream.
Xhci driver cannot call pci_set_power_state() on non-pci xhci host
controllers. For example, NVIDIA Tegra XHCI host controller which acts
as platform device with XHCI_SPURIOUS_WAKEUP quirk set in some platform
hits this issue during shutdown.
Cc: <stable@vger.kernel.org>
Fixes: 638298dc66ea ("xhci: Fix spurious wakeups after S5 on Haswell")
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed9ed5a89acba51b82bdff61144d4e4a4245ec8a upstream.
Add missing endpoint-type sanity checks to probe.
This specifically prevents a warning in USB core on URB submission when
fuzzing USB descriptors.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191202085610.12719-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84f60ca7b326ed8c08582417493982fe2573a9ad upstream.
The driver failed to initialise its receive-buffer pointer, something
which could lead to an illegal free on late probe errors.
Fix this by making sure to clear all driver data at allocation.
Fixes: 2032e2c2309d ("usb_gigaset: code cleanup")
Cc: stable <stable@vger.kernel.org> # 2.6.33
Cc: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191202085610.12719-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 53f35a39c3860baac1e5ca80bf052751cfb24a99 upstream.
Fix a general protection fault when accessing the endpoint descriptors
which could be triggered by a malicious device due to missing sanity
checks on the number of endpoints.
Reported-by: syzbot+35b1c403a14f5c89eba7@syzkaller.appspotmail.com
Fixes: 07dc1f9f2f80 ("[PATCH] isdn4linux: Siemens Gigaset drivers - M105 USB DECT adapter")
Cc: stable <stable@vger.kernel.org> # 2.6.17
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191202085610.12719-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2cdb20507fe2079a146459f9718b45d78cbbe61 upstream.
This undoes the previous call to alloc_chrdev_region() on failure,
and is probably what was meant originally given the label name.
Signed-off-by: Marcelo Diop-Gonzalez <marcgonzalez@google.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 187ac53e590c ("staging: vchiq_arm: rework probe and init functions")
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20191203153921.70540-1-marcgonzalez@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
