| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
move bitrate_masks into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Leave only vif-specific deinit stuff in remove_interface().
Move the global deinit (including power_off) to stop().
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Make sta use the global wl->links[hlid].tx_queue (by
considering its links map) instead of wl->tx_queue,
and then unify the tx and tx_reset flows for the
various vifs.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move last_tx_hlid into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The fw boot and initialization currently happens inside the
add_interface() callback. This is wrong, as add_interface is
called for each new vif. However, we due to some fw limitation
(we have to know the actual mac address on boot), we can't
completely move it into the start() callback.
Until the fw will be fixed, refactor the fw init into
a new function, and call it from add_interface()
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move recorded_ap_keys into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Add wlvif->links_map bitmap to represent all the links
allocated for this vif.
AP vif also has a sta_hlid_map bitmap, which represents
the links stations connected to it (sta_hlid_bitmap is
a subset of wlvif->links_map, which itself is a subset
of the global wl->links_map)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move ba_fields into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move rssi_thold and last_rssi_event into the per-interface
data, rather than being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move ps_poll_failures and psm_entry_retries into the per-interface
data, rather than being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move ps_compl into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move pspoll_work into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move default_key into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move beacon_int into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move dev_hlid into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Initialize the vif data according to the vif type
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move session_counter into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move ap_global_hlid and ap_bcast_hlid into the per-interface
data, rather than being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move sta_hlid into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move dev_role_id into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move role_id into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move aid into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move probereq into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move ssid and ssid_len into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move p2p field into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
set_bss_type is no longer evaluated, so delete it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move bss_type into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Use the per-interface vif->bss_conf instead of the global wl->bssid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move basic_rate into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
move rate_set into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Define a per-vif data struct.
This struct holds all the vif-specifc data, which is
currently being hold by the global wl struct.
Start by moving the basic_rate_set field into it.
NOTE: in order to make the patches a bit smaller, start by
using wl->vif in some functions, instead of changing all
the function prototypes at once. finally, wl->vif will be
removed altogether.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Split the init sequence into common commands (non role-specific)
and role-specific commands.
We still need to call the common commands only on add_interface()
(rather than on start()) as the fw must get the mac address
when uploading the nvs.
Future patches will refactor the init sequence further more.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[fixed a couple of sparse warnings]
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The mac address of the interface already exists in vif->addr.
Use it instead of wl->mac_addr.
It seems that due to some fw bug, we still need to set nvs->mac
to the actual mac addresss, otherwise the fw doesn't function
well (e.g. can't get dhcp address).
Thus, use wl->mac_addr for this purpose, and don't delete it yet.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The current wl12xx fw (7.3.0.0.77) supports both STA and AP mode, and
we no longer use AP-mode-specific quirks.
WL12XX_QUIRK_END_OF_TRANSACTION is still used for certain HWs, while
WL12XX_QUIRK_LPD_MODE is not used anymore.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The wl12xx FW supports HW channel switch. If we don't use it,
sometimes the firmware gets confused when recalibrating to the new
channel, causing RX problems. This commit adds HW channel switch
support by implementing the channell_switch op.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
[added one comment, remove the tx_flush and rephrased the commit message]
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The wiphy max_sched_scan_ie_len attribute was not set correctly and
remained as 0, so when IEs were being passed in a scheduled scan, we
were returning -EINVAL.
Fix this by setting the attribute properly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
p2p packets should go out only with OFDM rates.
Configure a new rate policy that will (later) be used
during p2p_find (when the p2p_cli / p2p_go interfaces
are in use, we won't have to use this policy, as
the configured rates should already be OFDM-only).
Additionally, update CONF_TX_MAX_RATE_CLASSES to reflect
the current value from the fw api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
|
|
the AR_SREV register does not seems to indicate whether AR9480 is
pci_express capable or not though the other information like macVersion
etc can be obtained properly. this fix is essential as ASPM won't be intialized
and its related driver functionality ath9k_hw_configpcipowersave won't be
called
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
this patch fixes the assumption of maximum number of GPIO pins present
in AR9287/AR9300. this fix is essential as we might encounter some
functionality issues involved in accessing the status of GPIO pins which
are all incorrectly assumed to be not within the range of max_num_gpio
of AR9300/AR9287 chipsets
Cc: stable@kernel.org
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Recent patches added support for resetting the SD8686 hardware when
commands time out, which seems to happen quite frequently soon after
resuming the system from a Wake-on-WLAN-triggered resume.
At http://dev.laptop.org/ticket/10969 we see the same thing happen
with transmits. In this case, the hardware will fail to respond to
a frame passed for transmission, and libertas (correctly) will block
all further commands and transmissions as the hardware can only
deal with one thing at a time. This results in a lockup while the
system waits indefinitely for the dead card to respond.
Hook up a TX lockup timer to detect this and reset the hardware.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.
The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
ops.conf_tx = conf_tx_op;
@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
conf_tx_op (
- struct ieee80211_hw *hw,
+ struct ieee80211_hw *hw, struct ieee80211_vif *vif,
u16 queue,
const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rename the iwlagn module as iwlwifi in preparation for future
changes. Add an alias to iwlagn for backward compatibility.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
this extends the bits for rf kill GPIO selection to [7:2] from [4:2] as
we use GPIO pin 11 as rfkill for AR9480 and also remove few unused
macros
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: "Hu, Russell" <rhu@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In failure case locks are not allocated in mwifiex_register().
So mwifiex_free_lock_list() routine call becomes redundant.
Also we don't need to check return type for mwifiex_init_lock_list()
routine. It never fails.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The commit "mwifiex: remove list traversal.."(fcf2176c87..)
wrongly modifies AMSDU aggregation check. Due to this even though
packet size for iperf traffic is already large, we unnecessarily
try to aggregate them which adds some delay. If Tx iperf is started
on UUT for 30 seconds, UUT keeps sending Tx packets for few more
seconds.
That commit is reverted to fix the problem.
Also, MIN_NUM_AMSDU check is moved inside the loop to optimize the
loop.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This was reported and tested by Martin Walter over at AVM GmbH Berlin.
This also applies to 3.0.1 so sendint to stable.
Cc: s.kirste@avm.de
Cc: d.friedel@avm.de
Cc: Martin Walter <m.walter@avm.de>
Cc: Peter Grabienski <pgrabien@qca.qualcomm.com>
Cc: stable@kernel.org
Tested-by: Martin Walter <m.walter@avm.de>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Recently mac80211 was changed to use nullfunc instead of probe
request for connection monitoring for tx ack status reporting
hardwares. Sometimes in congested network, STA got disconnected
quickly after the association. It was observered that the rate
control was not adopted to environment due to minimal transmission.
As the nullfunc are used for monitoring purpose, these frames should
not be sacrificed for rate control updation. So it is better to send
the monitoring null func frames at minimum rate that could help to
retain the connection.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add a gpio setup function which gives a chance to set up
platform specific configuration such as pin multiplexing,
input/output direction at the runtime or booting time.
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Allow injected unicast frames to be sent without having to wait
for an ACK.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
