1 files changed, 182 insertions, 156 deletions

diff --git a/net/mac80211/mlme.c b/net/mac80211/mlme.c
index f76da5b3f5c5..c8836fa7d627 100644
--- a/net/mac80211/mlme.c
+++ b/net/mac80211/mlme.c
@@ -171,122 +171,64 @@ static int ecw2cw(int ecw)
 	return (1 << ecw) - 1;
 }
 
-/*
- * ieee80211_enable_ht should be called only after the operating band
- * has been determined as ht configuration depends on the hw's
- * HT abilities for a specific band.
- */
-static u32 ieee80211_enable_ht(struct ieee80211_sub_if_data *sdata,
-			       struct ieee80211_ht_info *hti,
-			       const u8 *bssid, u16 ap_ht_cap_flags,
-			       bool beacon_htcap_ie)
+static u32 ieee80211_config_ht_tx(struct ieee80211_sub_if_data *sdata,
+				  struct ieee80211_ht_operation *ht_oper,
+				  const u8 *bssid, bool reconfig)
 {
 	struct ieee80211_local *local = sdata->local;
 	struct ieee80211_supported_band *sband;
 	struct sta_info *sta;
 	u32 changed = 0;
-	int hti_cfreq;
 	u16 ht_opmode;
-	bool enable_ht = true;
-	enum nl80211_channel_type prev_chantype;
-	enum nl80211_channel_type rx_channel_type = NL80211_CHAN_NO_HT;
-	enum nl80211_channel_type tx_channel_type;
+	bool disable_40 = false;
 
 	sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
-	prev_chantype = sdata->vif.bss_conf.channel_type;
 
-
-	hti_cfreq = ieee80211_channel_to_frequency(hti->control_chan,
-						   sband->band);
-	/* check that channel matches the right operating channel */
-	if (local->hw.conf.channel->center_freq != hti_cfreq) {
-		/* Some APs mess this up, evidently.
-		 * Netgear WNDR3700 sometimes reports 4 higher than
-		 * the actual channel, for instance.
-		 */
-		printk(KERN_DEBUG
-		       "%s: Wrong control channel in association"
-		       " response: configured center-freq: %d"
-		       " hti-cfreq: %d  hti->control_chan: %d"
-		       " band: %d.  Disabling HT.\n",
-		       sdata->name,
-		       local->hw.conf.channel->center_freq,
-		       hti_cfreq, hti->control_chan,
-		       sband->band);
-		enable_ht = false;
-	}
-
-	if (enable_ht) {
-		rx_channel_type = NL80211_CHAN_HT20;
-
-		if (!(ap_ht_cap_flags & IEEE80211_HT_CAP_40MHZ_INTOLERANT) &&
-		    !ieee80111_cfg_override_disables_ht40(sdata) &&
-		    (sband->ht_cap.cap & IEEE80211_HT_CAP_SUP_WIDTH_20_40) &&
-		    (hti->ht_param & IEEE80211_HT_PARAM_CHAN_WIDTH_ANY)) {
-			switch(hti->ht_param & IEEE80211_HT_PARAM_CHA_SEC_OFFSET) {
-			case IEEE80211_HT_PARAM_CHA_SEC_ABOVE:
-				rx_channel_type = NL80211_CHAN_HT40PLUS;
-				break;
-			case IEEE80211_HT_PARAM_CHA_SEC_BELOW:
-				rx_channel_type = NL80211_CHAN_HT40MINUS;
-				break;
-			}
-		}
+	switch (sdata->vif.bss_conf.channel_type) {
+	case NL80211_CHAN_HT40PLUS:
+		if (local->hw.conf.channel->flags & IEEE80211_CHAN_NO_HT40PLUS)
+			disable_40 = true;
+		break;
+	case NL80211_CHAN_HT40MINUS:
+		if (local->hw.conf.channel->flags & IEEE80211_CHAN_NO_HT40MINUS)
+			disable_40 = true;
+		break;
+	default:
+		break;
 	}
 
-	tx_channel_type = ieee80211_get_tx_channel_type(local, rx_channel_type);
-
-	if (local->tmp_channel)
-		local->tmp_channel_type = rx_channel_type;
+	/* This can change during the lifetime of the BSS */
+	if (!(ht_oper->ht_param & IEEE80211_HT_PARAM_CHAN_WIDTH_ANY))
+		disable_40 = true;
 
-	if (!ieee80211_set_channel_type(local, sdata, rx_channel_type)) {
-		/* can only fail due to HT40+/- mismatch */
-		rx_channel_type = NL80211_CHAN_HT20;
-		WARN_ON(!ieee80211_set_channel_type(local, sdata,
-						    rx_channel_type));
-	}
-
-	if (beacon_htcap_ie && (prev_chantype != rx_channel_type)) {
-		/*
-		 * Whenever the AP announces the HT mode change that can be
-		 * 40MHz intolerant or etc., it would be safer to stop tx
-		 * queues before doing hw config to avoid buffer overflow.
-		 */
-		ieee80211_stop_queues_by_reason(&sdata->local->hw,
-				IEEE80211_QUEUE_STOP_REASON_CHTYPE_CHANGE);
+	mutex_lock(&local->sta_mtx);
+	sta = sta_info_get(sdata, bssid);
 
-		/* flush out all packets */
-		synchronize_net();
+	WARN_ON_ONCE(!sta);
 
-		drv_flush(local, false);
-	}
+	if (sta && !sta->supports_40mhz)
+		disable_40 = true;
 
-	/* channel_type change automatically detected */
-	ieee80211_hw_config(local, 0);
+	if (sta && (!reconfig ||
+		    (disable_40 != !!(sta->sta.ht_cap.cap &
+					IEEE80211_HT_CAP_SUP_WIDTH_20_40)))) {
 
-	if (prev_chantype != tx_channel_type) {
-		rcu_read_lock();
-		sta = sta_info_get(sdata, bssid);
-		if (sta)
-			rate_control_rate_update(local, sband, sta,
-						 IEEE80211_RC_HT_CHANGED,
-						 tx_channel_type);
-		rcu_read_unlock();
+		if (disable_40)
+			sta->sta.ht_cap.cap &= ~IEEE80211_HT_CAP_SUP_WIDTH_20_40;
+		else
+			sta->sta.ht_cap.cap |= IEEE80211_HT_CAP_SUP_WIDTH_20_40;
 
-		if (beacon_htcap_ie)
-			ieee80211_wake_queues_by_reason(&sdata->local->hw,
-				IEEE80211_QUEUE_STOP_REASON_CHTYPE_CHANGE);
+		rate_control_rate_update(local, sband, sta,
+					 IEEE80211_RC_BW_CHANGED);
 	}
+	mutex_unlock(&local->sta_mtx);
 
-	ht_opmode = le16_to_cpu(hti->operation_mode);
+	ht_opmode = le16_to_cpu(ht_oper->operation_mode);
 
 	/* if bss configuration changed store the new one */
-	if (sdata->ht_opmode_valid != enable_ht ||
-	    sdata->vif.bss_conf.ht_operation_mode != ht_opmode ||
-	    prev_chantype != rx_channel_type) {
+	if (!reconfig || (sdata->vif.bss_conf.ht_operation_mode != ht_opmode)) {
 		changed |= BSS_CHANGED_HT;
 		sdata->vif.bss_conf.ht_operation_mode = ht_opmode;
-		sdata->ht_opmode_valid = enable_ht;
 	}
 
 	return changed;
@@ -316,12 +258,12 @@ static int ieee80211_compatible_rates(const u8 *supp_rates, int supp_rates_len,
 }
 
 static void ieee80211_add_ht_ie(struct ieee80211_sub_if_data *sdata,
-				struct sk_buff *skb, const u8 *ht_info_ie,
+				struct sk_buff *skb, const u8 *ht_oper_ie,
 				struct ieee80211_supported_band *sband,
 				struct ieee80211_channel *channel,
 				enum ieee80211_smps_mode smps)
 {
-	struct ieee80211_ht_info *ht_info;
+	struct ieee80211_ht_operation *ht_oper;
 	u8 *pos;
 	u32 flags = channel->flags;
 	u16 cap;
@@ -329,21 +271,21 @@ static void ieee80211_add_ht_ie(struct ieee80211_sub_if_data *sdata,
 
 	BUILD_BUG_ON(sizeof(ht_cap) != sizeof(sband->ht_cap));
 
-	if (!ht_info_ie)
+	if (!ht_oper_ie)
 		return;
 
-	if (ht_info_ie[1] < sizeof(struct ieee80211_ht_info))
+	if (ht_oper_ie[1] < sizeof(struct ieee80211_ht_operation))
 		return;
 
 	memcpy(&ht_cap, &sband->ht_cap, sizeof(ht_cap));
 	ieee80211_apply_htcap_overrides(sdata, &ht_cap);
 
-	ht_info = (struct ieee80211_ht_info *)(ht_info_ie + 2);
+	ht_oper = (struct ieee80211_ht_operation *)(ht_oper_ie + 2);
 
 	/* determine capability flags */
 	cap = ht_cap.cap;
 
-	switch (ht_info->ht_param & IEEE80211_HT_PARAM_CHA_SEC_OFFSET) {
+	switch (ht_oper->ht_param & IEEE80211_HT_PARAM_CHA_SEC_OFFSET) {
 	case IEEE80211_HT_PARAM_CHA_SEC_ABOVE:
 		if (flags & IEEE80211_CHAN_NO_HT40PLUS) {
 			cap &= ~IEEE80211_HT_CAP_SUP_WIDTH_20_40;
@@ -358,6 +300,16 @@ static void ieee80211_add_ht_ie(struct ieee80211_sub_if_data *sdata,
 		break;
 	}
 
+	/*
+	 * If 40 MHz was disabled associate as though we weren't
+	 * capable of 40 MHz -- some broken APs will never fall
+	 * back to trying to transmit in 20 MHz.
+	 */
+	if (sdata->u.mgd.flags & IEEE80211_STA_DISABLE_40MHZ) {
+		cap &= ~IEEE80211_HT_CAP_SUP_WIDTH_20_40;
+		cap &= ~IEEE80211_HT_CAP_SGI_40;
+	}
+
 	/* set SM PS mode properly */
 	cap &= ~IEEE80211_HT_CAP_SM_PS;
 	switch (smps) {
@@ -557,7 +509,7 @@ static void ieee80211_send_assoc(struct ieee80211_sub_if_data *sdata)
 	}
 
 	if (!(ifmgd->flags & IEEE80211_STA_DISABLE_11N))
-		ieee80211_add_ht_ie(sdata, skb, assoc_data->ht_information_ie,
+		ieee80211_add_ht_ie(sdata, skb, assoc_data->ht_operation_ie,
 				    sband, local->oper_channel, ifmgd->ap_smps);
 
 	/* if present, add any custom non-vendor IEs that go after HT */
@@ -1182,7 +1134,7 @@ static void ieee80211_sta_wmm_params(struct ieee80211_local *local,
 	if (!local->ops->conf_tx)
 		return;
 
-	if (local->hw.queues < 4)
+	if (local->hw.queues < IEEE80211_NUM_ACS)
 		return;
 
 	if (!wmm_param)
@@ -1435,7 +1387,6 @@ static void ieee80211_set_disassoc(struct ieee80211_sub_if_data *sdata,
 	sdata->vif.bss_conf.assoc = false;
 
 	/* on the next assoc, re-program HT parameters */
-	sdata->ht_opmode_valid = false;
 	memset(&ifmgd->ht_capa, 0, sizeof(ifmgd->ht_capa));
 	memset(&ifmgd->ht_capa_mask, 0, sizeof(ifmgd->ht_capa_mask));
 
@@ -1496,19 +1447,24 @@ void ieee80211_sta_rx_notify(struct ieee80211_sub_if_data *sdata,
 static void ieee80211_reset_ap_probe(struct ieee80211_sub_if_data *sdata)
 {
 	struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
+	struct ieee80211_local *local = sdata->local;
 
+	mutex_lock(&local->mtx);
 	if (!(ifmgd->flags & (IEEE80211_STA_BEACON_POLL |
-			      IEEE80211_STA_CONNECTION_POLL)))
-	    return;
+			      IEEE80211_STA_CONNECTION_POLL))) {
+		mutex_unlock(&local->mtx);
+		return;
+	}
 
 	ifmgd->flags &= ~(IEEE80211_STA_CONNECTION_POLL |
 			  IEEE80211_STA_BEACON_POLL);
-	mutex_lock(&sdata->local->iflist_mtx);
-	ieee80211_recalc_ps(sdata->local, -1);
-	mutex_unlock(&sdata->local->iflist_mtx);
+
+	mutex_lock(&local->iflist_mtx);
+	ieee80211_recalc_ps(local, -1);
+	mutex_unlock(&local->iflist_mtx);
 
 	if (sdata->local->hw.flags & IEEE80211_HW_CONNECTION_MONITOR)
-		return;
+		goto out;
 
 	/*
 	 * We've received a probe response, but are not sure whether
@@ -1520,6 +1476,9 @@ static void ieee80211_reset_ap_probe(struct ieee80211_sub_if_data *sdata)
 	mod_timer(&ifmgd->conn_mon_timer,
 		  round_jiffies_up(jiffies +
 				   IEEE80211_CONNECTION_IDLE_TIME));
+out:
+	ieee80211_run_deferred_scan(local);
+	mutex_unlock(&local->mtx);
 }
 
 void ieee80211_sta_tx_notify(struct ieee80211_sub_if_data *sdata,
@@ -1567,14 +1526,23 @@ static void ieee80211_mgd_probe_ap_send(struct ieee80211_sub_if_data *sdata)
 		ifmgd->nullfunc_failed = false;
 		ieee80211_send_nullfunc(sdata->local, sdata, 0);
 	} else {
+		int ssid_len;
+
 		ssid = ieee80211_bss_get_ie(ifmgd->associated, WLAN_EID_SSID);
-		ieee80211_send_probe_req(sdata, dst, ssid + 2, ssid[1], NULL, 0,
-					 (u32) -1, true, false);
+		if (WARN_ON_ONCE(ssid == NULL))
+			ssid_len = 0;
+		else
+			ssid_len = ssid[1];
+
+		ieee80211_send_probe_req(sdata, dst, ssid + 2, ssid_len, NULL,
+					 0, (u32) -1, true, false);
 	}
 
 	ifmgd->probe_send_count++;
 	ifmgd->probe_timeout = jiffies + msecs_to_jiffies(probe_wait_ms);
 	run_again(ifmgd, ifmgd->probe_timeout);
+	if (sdata->local->hw.flags & IEEE80211_HW_REPORTS_TX_ACK_STATUS)
+		drv_flush(sdata->local, false);
 }
 
 static void ieee80211_mgd_probe_ap(struct ieee80211_sub_if_data *sdata,
@@ -1586,17 +1554,18 @@ static void ieee80211_mgd_probe_ap(struct ieee80211_sub_if_data *sdata,
 	if (!ieee80211_sdata_running(sdata))
 		return;
 
-	if (sdata->local->scanning)
-		return;
-
-	if (sdata->local->tmp_channel)
-		return;
-
 	mutex_lock(&ifmgd->mtx);
 
 	if (!ifmgd->associated)
 		goto out;
 
+	mutex_lock(&sdata->local->mtx);
+
+	if (sdata->local->tmp_channel || sdata->local->scanning) {
+		mutex_unlock(&sdata->local->mtx);
+		goto out;
+	}
+
 #ifdef CONFIG_MAC80211_VERBOSE_DEBUG
 	if (beacon && net_ratelimit())
 		printk(KERN_DEBUG "%s: detected beacon loss from AP "
@@ -1623,6 +1592,8 @@ static void ieee80211_mgd_probe_ap(struct ieee80211_sub_if_data *sdata,
 	else
 		ifmgd->flags |= IEEE80211_STA_CONNECTION_POLL;
 
+	mutex_unlock(&sdata->local->mtx);
+
 	if (already)
 		goto out;
 
@@ -1643,6 +1614,7 @@ struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw,
 	struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
 	struct sk_buff *skb;
 	const u8 *ssid;
+	int ssid_len;
 
 	if (WARN_ON(sdata->vif.type != NL80211_IFTYPE_STATION))
 		return NULL;
@@ -1653,8 +1625,13 @@ struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw,
 		return NULL;
 
 	ssid = ieee80211_bss_get_ie(ifmgd->associated, WLAN_EID_SSID);
+	if (WARN_ON_ONCE(ssid == NULL))
+		ssid_len = 0;
+	else
+		ssid_len = ssid[1];
+
 	skb = ieee80211_build_probe_req(sdata, ifmgd->associated->bssid,
-					(u32) -1, ssid + 2, ssid[1],
+					(u32) -1, ssid + 2, ssid_len,
 					NULL, 0, true);
 
 	return skb;
@@ -2000,7 +1977,6 @@ static bool ieee80211_assoc_success(struct ieee80211_sub_if_data *sdata,
 	struct ieee80211_bss_conf *bss_conf = &sdata->vif.bss_conf;
 	u32 changed = 0;
 	int err;
-	u16 ap_ht_cap_flags;
 
 	/* AssocResp and ReassocResp have identical structure */
 
@@ -2051,7 +2027,8 @@ static bool ieee80211_assoc_success(struct ieee80211_sub_if_data *sdata,
 		ieee80211_ht_cap_ie_to_sta_ht_cap(sdata, sband,
 				elems.ht_cap_elem, &sta->sta.ht_cap);
 
-	ap_ht_cap_flags = sta->sta.ht_cap.cap;
+	sta->supports_40mhz =
+		sta->sta.ht_cap.cap & IEEE80211_HT_CAP_SUP_WIDTH_20_40;
 
 	rate_control_rate_init(sta);
 
@@ -2092,11 +2069,10 @@ static bool ieee80211_assoc_success(struct ieee80211_sub_if_data *sdata,
 		ieee80211_set_wmm_default(sdata, false);
 	changed |= BSS_CHANGED_QOS;
 
-	if (elems.ht_info_elem && elems.wmm_param &&
+	if (elems.ht_operation && elems.wmm_param &&
 	    !(ifmgd->flags & IEEE80211_STA_DISABLE_11N))
-		changed |= ieee80211_enable_ht(sdata, elems.ht_info_elem,
-					       cbss->bssid, ap_ht_cap_flags,
-					       false);
+		changed |= ieee80211_config_ht_tx(sdata, elems.ht_operation,
+						  cbss->bssid, false);
 
 	/* set AID and assoc capability,
 	 * ieee80211_set_associated() will tell the driver */
@@ -2319,7 +2295,7 @@ static const u64 care_about_ies =
 	(1ULL << WLAN_EID_CHANNEL_SWITCH) |
 	(1ULL << WLAN_EID_PWR_CONSTRAINT) |
 	(1ULL << WLAN_EID_HT_CAPABILITY) |
-	(1ULL << WLAN_EID_HT_INFORMATION);
+	(1ULL << WLAN_EID_HT_OPERATION);
 
 static void ieee80211_rx_mgmt_beacon(struct ieee80211_sub_if_data *sdata,
 				     struct ieee80211_mgmt *mgmt,
@@ -2468,11 +2444,13 @@ static void ieee80211_rx_mgmt_beacon(struct ieee80211_sub_if_data *sdata,
 	if (local->hw.flags & IEEE80211_HW_PS_NULLFUNC_STACK) {
 		if (directed_tim) {
 			if (local->hw.conf.dynamic_ps_timeout > 0) {
-				local->hw.conf.flags &= ~IEEE80211_CONF_PS;
-				ieee80211_hw_config(local,
-						    IEEE80211_CONF_CHANGE_PS);
+				if (local->hw.conf.flags & IEEE80211_CONF_PS) {
+					local->hw.conf.flags &= ~IEEE80211_CONF_PS;
+					ieee80211_hw_config(local,
+							    IEEE80211_CONF_CHANGE_PS);
+				}
 				ieee80211_send_nullfunc(local, sdata, 0);
-			} else {
+			} else if (!local->pspolling && sdata->u.mgd.powersave) {
 				local->pspolling = true;
 
 				/*
@@ -2504,31 +2482,14 @@ static void ieee80211_rx_mgmt_beacon(struct ieee80211_sub_if_data *sdata,
 			erp_valid, erp_value);
 
 
-	if (elems.ht_cap_elem && elems.ht_info_elem && elems.wmm_param &&
+	if (elems.ht_cap_elem && elems.ht_operation && elems.wmm_param &&
 	    !(ifmgd->flags & IEEE80211_STA_DISABLE_11N)) {
-		struct sta_info *sta;
 		struct ieee80211_supported_band *sband;
-		u16 ap_ht_cap_flags;
-
-		rcu_read_lock();
-
-		sta = sta_info_get(sdata, bssid);
-		if (WARN_ON(!sta)) {
-			rcu_read_unlock();
-			return;
-		}
 
 		sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
 
-		ieee80211_ht_cap_ie_to_sta_ht_cap(sdata, sband,
-				elems.ht_cap_elem, &sta->sta.ht_cap);
-
-		ap_ht_cap_flags = sta->sta.ht_cap.cap;
-
-		rcu_read_unlock();
-
-		changed |= ieee80211_enable_ht(sdata, elems.ht_info_elem,
-					       bssid, ap_ht_cap_flags, true);
+		changed |= ieee80211_config_ht_tx(sdata, elems.ht_operation,
+						  bssid, true);
 	}
 
 	/* Note: country IE parsing is done for us by cfg80211 */
@@ -3060,6 +3021,11 @@ static int ieee80211_prep_connection(struct ieee80211_sub_if_data *sdata,
 	struct sta_info *sta;
 	bool have_sta = false;
 	int err;
+	int ht_cfreq;
+	enum nl80211_channel_type channel_type = NL80211_CHAN_NO_HT;
+	const u8 *ht_oper_ie;
+	const struct ieee80211_ht_operation *ht_oper = NULL;
+	struct ieee80211_supported_band *sband;
 
 	if (WARN_ON(!ifmgd->auth_data && !ifmgd->assoc_data))
 		return -EINVAL;
@@ -3081,17 +3047,76 @@ static int ieee80211_prep_connection(struct ieee80211_sub_if_data *sdata,
 	mutex_unlock(&local->mtx);
 
 	/* switch to the right channel */
+	sband = local->hw.wiphy->bands[cbss->channel->band];
+
+	ifmgd->flags &= ~IEEE80211_STA_DISABLE_40MHZ;
+
+	if (sband->ht_cap.ht_supported) {
+		ht_oper_ie = cfg80211_find_ie(WLAN_EID_HT_OPERATION,
+					      cbss->information_elements,
+					      cbss->len_information_elements);
+		if (ht_oper_ie && ht_oper_ie[1] >= sizeof(*ht_oper))
+			ht_oper = (void *)(ht_oper_ie + 2);
+	}
+
+	if (ht_oper) {
+		ht_cfreq = ieee80211_channel_to_frequency(ht_oper->primary_chan,
+							  cbss->channel->band);
+		/* check that channel matches the right operating channel */
+		if (cbss->channel->center_freq != ht_cfreq) {
+			/*
+			 * It's possible that some APs are confused here;
+			 * Netgear WNDR3700 sometimes reports 4 higher than
+			 * the actual channel in association responses, but
+			 * since we look at probe response/beacon data here
+			 * it should be OK.
+			 */
+			printk(KERN_DEBUG
+			       "%s: Wrong control channel: center-freq: %d"
+			       " ht-cfreq: %d ht->primary_chan: %d"
+			       " band: %d. Disabling HT.\n",
+			       sdata->name, cbss->channel->center_freq,
+			       ht_cfreq, ht_oper->primary_chan,
+			       cbss->channel->band);
+			ht_oper = NULL;
+		}
+	}
+
+	if (ht_oper) {
+		channel_type = NL80211_CHAN_HT20;
+
+		if (sband->ht_cap.cap & IEEE80211_HT_CAP_SUP_WIDTH_20_40) {
+			switch (ht_oper->ht_param &
+					IEEE80211_HT_PARAM_CHA_SEC_OFFSET) {
+			case IEEE80211_HT_PARAM_CHA_SEC_ABOVE:
+				channel_type = NL80211_CHAN_HT40PLUS;
+				break;
+			case IEEE80211_HT_PARAM_CHA_SEC_BELOW:
+				channel_type = NL80211_CHAN_HT40MINUS;
+				break;
+			}
+		}
+	}
+
+	if (!ieee80211_set_channel_type(local, sdata, channel_type)) {
+		/* can only fail due to HT40+/- mismatch */
+		channel_type = NL80211_CHAN_HT20;
+		printk(KERN_DEBUG
+		       "%s: disabling 40 MHz due to multi-vif mismatch\n",
+		       sdata->name);
+		ifmgd->flags |= IEEE80211_STA_DISABLE_40MHZ;
+		WARN_ON(!ieee80211_set_channel_type(local, sdata,
+						    channel_type));
+	}
+
 	local->oper_channel = cbss->channel;
-	ieee80211_hw_config(local, IEEE80211_CONF_CHANGE_CHANNEL);
+	ieee80211_hw_config(local, 0);
 
 	if (!have_sta) {
-		struct ieee80211_supported_band *sband;
 		u32 rates = 0, basic_rates = 0;
 		bool have_higher_than_11mbit;
 		int min_rate = INT_MAX, min_rate_index = -1;
 
-		sband = sdata->local->hw.wiphy->bands[cbss->channel->band];
-
 		ieee80211_get_rates(sband, bss->supp_rates,
 				    bss->supp_rates_len,
 				    &rates, &basic_rates,
@@ -3311,7 +3336,7 @@ int ieee80211_mgd_assoc(struct ieee80211_sub_if_data *sdata,
 	/* Also disable HT if we don't support it or the AP doesn't use WMM */
 	sband = local->hw.wiphy->bands[req->bss->channel->band];
 	if (!sband->ht_cap.ht_supported ||
-	    local->hw.queues < 4 || !bss->wmm_used)
+	    local->hw.queues < IEEE80211_NUM_ACS || !bss->wmm_used)
 		ifmgd->flags |= IEEE80211_STA_DISABLE_11N;
 
 	memcpy(&ifmgd->ht_capa, &req->ht_capa, sizeof(ifmgd->ht_capa));
@@ -3334,11 +3359,12 @@ int ieee80211_mgd_assoc(struct ieee80211_sub_if_data *sdata,
 		ifmgd->ap_smps = ifmgd->req_smps;
 
 	assoc_data->capability = req->bss->capability;
-	assoc_data->wmm = bss->wmm_used && (local->hw.queues >= 4);
+	assoc_data->wmm = bss->wmm_used &&
+			  (local->hw.queues >= IEEE80211_NUM_ACS);
 	assoc_data->supp_rates = bss->supp_rates;
 	assoc_data->supp_rates_len = bss->supp_rates_len;
-	assoc_data->ht_information_ie =
-		ieee80211_bss_get_ie(req->bss, WLAN_EID_HT_INFORMATION);
+	assoc_data->ht_operation_ie =
+		ieee80211_bss_get_ie(req->bss, WLAN_EID_HT_OPERATION);
 
 	if (bss->wmm_used && bss->uapsd_supported &&
 	    (sdata->local->hw.flags & IEEE80211_HW_SUPPORTS_UAPSD)) {