diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/asm-powerpc/prom.h | 2 | ||||
| -rw-r--r-- | include/asm-powerpc/smu.h | 153 | ||||
| -rw-r--r-- | include/asm-ppc/prom.h | 2 | ||||
| -rw-r--r-- | include/asm-ppc64/prom.h | 2 | ||||
| -rw-r--r-- | include/linux/proc_fs.h | 9 |
5 files changed, 149 insertions, 19 deletions
diff --git a/include/asm-powerpc/prom.h b/include/asm-powerpc/prom.h index 7587bf5f38c6..f999df1c5c90 100644 --- a/include/asm-powerpc/prom.h +++ b/include/asm-powerpc/prom.h @@ -203,7 +203,7 @@ extern int prom_n_addr_cells(struct device_node* np); extern int prom_n_size_cells(struct device_node* np); extern int prom_n_intr_cells(struct device_node* np); extern void prom_get_irq_senses(unsigned char *senses, int off, int max); -extern void prom_add_property(struct device_node* np, struct property* prop); +extern int prom_add_property(struct device_node* np, struct property* prop); #ifdef CONFIG_PPC32 /* diff --git a/include/asm-powerpc/smu.h b/include/asm-powerpc/smu.h index 959bad660233..76c29a9784dd 100644 --- a/include/asm-powerpc/smu.h +++ b/include/asm-powerpc/smu.h @@ -20,16 +20,52 @@ /* * Partition info commands * - * I do not know what those are for at this point + * These commands are used to retreive the sdb-partition-XX datas from + * the SMU. The lenght is always 2. First byte is the subcommand code + * and second byte is the partition ID. + * + * The reply is 6 bytes: + * + * - 0..1 : partition address + * - 2 : a byte containing the partition ID + * - 3 : length (maybe other bits are rest of header ?) + * + * The data must then be obtained with calls to another command: + * SMU_CMD_MISC_ee_GET_DATABLOCK_REC (described below). */ #define SMU_CMD_PARTITION_COMMAND 0x3e +#define SMU_CMD_PARTITION_LATEST 0x01 +#define SMU_CMD_PARTITION_BASE 0x02 +#define SMU_CMD_PARTITION_UPDATE 0x03 /* * Fan control * - * This is a "mux" for fan control commands, first byte is the - * "sub" command. + * This is a "mux" for fan control commands. The command seem to + * act differently based on the number of arguments. With 1 byte + * of argument, this seem to be queries for fans status, setpoint, + * etc..., while with 0xe arguments, we will set the fans speeds. + * + * Queries (1 byte arg): + * --------------------- + * + * arg=0x01: read RPM fans status + * arg=0x02: read RPM fans setpoint + * arg=0x11: read PWM fans status + * arg=0x12: read PWM fans setpoint + * + * the "status" queries return the current speed while the "setpoint" ones + * return the programmed/target speed. It _seems_ that the result is a bit + * mask in the first byte of active/available fans, followed by 6 words (16 + * bits) containing the requested speed. + * + * Setpoint (14 bytes arg): + * ------------------------ + * + * first arg byte is 0 for RPM fans and 0x10 for PWM. Second arg byte is the + * mask of fans affected by the command. Followed by 6 words containing the + * setpoint value for selected fans in the mask (or 0 if mask value is 0) */ #define SMU_CMD_FAN_COMMAND 0x4a @@ -156,6 +192,14 @@ #define SMU_CMD_POWER_SHUTDOWN "SHUTDOWN" #define SMU_CMD_POWER_VOLTAGE_SLEW "VSLEW" +/* + * Read ADC sensors + * + * This command takes one byte of parameter: the sensor ID (or "reg" + * value in the device-tree) and returns a 16 bits value + */ +#define SMU_CMD_READ_ADC 0xd8 + /* Misc commands * * This command seem to be a grab bag of various things @@ -176,6 +220,25 @@ * Misc commands * * This command seem to be a grab bag of various things + * + * SMU_CMD_MISC_ee_GET_DATABLOCK_REC is used, among others, to + * transfer blocks of data from the SMU. So far, I've decrypted it's + * usage to retreive partition data. In order to do that, you have to + * break your transfer in "chunks" since that command cannot transfer + * more than a chunk at a time. The chunk size used by OF is 0xe bytes, + * but it seems that the darwin driver will let you do 0x1e bytes if + * your "PMU" version is >= 0x30. You can get the "PMU" version apparently + * either in the last 16 bits of property "smu-version-pmu" or as the 16 + * bytes at offset 1 of "smu-version-info" + * + * For each chunk, the command takes 7 bytes of arguments: + * byte 0: subcommand code (0x02) + * byte 1: 0x04 (always, I don't know what it means, maybe the address + * space to use or some other nicety. It's hard coded in OF) + * byte 2..5: SMU address of the chunk (big endian 32 bits) + * byte 6: size to transfer (up to max chunk size) + * + * The data is returned directly */ #define SMU_CMD_MISC_ee_COMMAND 0xee #define SMU_CMD_MISC_ee_GET_DATABLOCK_REC 0x02 @@ -353,21 +416,26 @@ struct smu_sdbp_header { __u8 flags; }; -/* - * 32 bits integers are usually encoded with 2x16 bits swapped, - * this demangles them + + /* + * demangle 16 and 32 bits integer in some SMU partitions + * (currently, afaik, this concerns only the FVT partition + * (0x12) */ -#define SMU_U32_MIX(x) ((((x) << 16) & 0xffff0000u) | (((x) >> 16) & 0xffffu)) +#define SMU_U16_MIX(x) le16_to_cpu(x); +#define SMU_U32_MIX(x) ((((x) & 0xff00ff00u) >> 8)|(((x) & 0x00ff00ffu) << 8)) + /* This is the definition of the SMU sdb-partition-0x12 table (called * CPU F/V/T operating points in Darwin). The definition for all those * SMU tables should be moved to some separate file */ -#define SMU_SDB_FVT_ID 0x12 +#define SMU_SDB_FVT_ID 0x12 struct smu_sdbp_fvt { __u32 sysclk; /* Base SysClk frequency in Hz for - * this operating point + * this operating point. Value need to + * be unmixed with SMU_U32_MIX() */ __u8 pad; __u8 maxtemp; /* Max temp. supported by this @@ -376,10 +444,73 @@ struct smu_sdbp_fvt { __u16 volts[3]; /* CPU core voltage for the 3 * PowerTune modes, a mode with - * 0V = not supported. + * 0V = not supported. Value need + * to be unmixed with SMU_U16_MIX() */ }; +/* This partition contains voltage & current sensor calibration + * informations + */ +#define SMU_SDB_CPUVCP_ID 0x21 + +struct smu_sdbp_cpuvcp { + __u16 volt_scale; /* u4.12 fixed point */ + __s16 volt_offset; /* s4.12 fixed point */ + __u16 curr_scale; /* u4.12 fixed point */ + __s16 curr_offset; /* s4.12 fixed point */ + __s32 power_quads[3]; /* s4.28 fixed point */ +}; + +/* This partition contains CPU thermal diode calibration + */ +#define SMU_SDB_CPUDIODE_ID 0x18 + +struct smu_sdbp_cpudiode { + __u16 m_value; /* u1.15 fixed point */ + __s16 b_value; /* s10.6 fixed point */ + +}; + +/* This partition contains Slots power calibration + */ +#define SMU_SDB_SLOTSPOW_ID 0x78 + +struct smu_sdbp_slotspow { + __u16 pow_scale; /* u4.12 fixed point */ + __s16 pow_offset; /* s4.12 fixed point */ +}; + +/* This partition contains machine specific version information about + * the sensor/control layout + */ +#define SMU_SDB_SENSORTREE_ID 0x25 + +struct smu_sdbp_sensortree { + u8 model_id; + u8 unknown[3]; +}; + +/* This partition contains CPU thermal control PID informations. So far + * only single CPU machines have been seen with an SMU, so we assume this + * carries only informations for those + */ +#define SMU_SDB_CPUPIDDATA_ID 0x17 + +struct smu_sdbp_cpupiddata { + u8 unknown1; + u8 target_temp_delta; + u8 unknown2; + u8 history_len; + s16 power_adj; + u16 max_power; + s32 gp,gr,gd; +}; + + +/* Other partitions without known structures */ +#define SMU_SDB_DEBUG_SWITCHES_ID 0x05 + #ifdef __KERNEL__ /* * This returns the pointer to an SMU "sdb" partition data or NULL @@ -423,8 +554,10 @@ struct smu_user_cmd_hdr __u32 cmdtype; #define SMU_CMDTYPE_SMU 0 /* SMU command */ #define SMU_CMDTYPE_WANTS_EVENTS 1 /* switch fd to events mode */ +#define SMU_CMDTYPE_GET_PARTITION 2 /* retreive an sdb partition */ __u8 cmd; /* SMU command byte */ + __u8 pad[3]; /* padding */ __u32 data_len; /* Lenght of data following */ }; diff --git a/include/asm-ppc/prom.h b/include/asm-ppc/prom.h index 75c0637acdc8..3e39827ed566 100644 --- a/include/asm-ppc/prom.h +++ b/include/asm-ppc/prom.h @@ -93,7 +93,7 @@ extern int device_is_compatible(struct device_node *device, const char *); extern int machine_is_compatible(const char *compat); extern unsigned char *get_property(struct device_node *node, const char *name, int *lenp); -extern void prom_add_property(struct device_node* np, struct property* prop); +extern int prom_add_property(struct device_node* np, struct property* prop); extern void prom_get_irq_senses(unsigned char *, int, int); extern int prom_n_addr_cells(struct device_node* np); extern int prom_n_size_cells(struct device_node* np); diff --git a/include/asm-ppc64/prom.h b/include/asm-ppc64/prom.h index bdb47174ff0e..76bb0266d67c 100644 --- a/include/asm-ppc64/prom.h +++ b/include/asm-ppc64/prom.h @@ -213,6 +213,6 @@ extern int prom_n_addr_cells(struct device_node* np); extern int prom_n_size_cells(struct device_node* np); extern int prom_n_intr_cells(struct device_node* np); extern void prom_get_irq_senses(unsigned char *senses, int off, int max); -extern void prom_add_property(struct device_node* np, struct property* prop); +extern int prom_add_property(struct device_node* np, struct property* prop); #endif /* _PPC64_PROM_H */ diff --git a/include/linux/proc_fs.h b/include/linux/proc_fs.h index 0563581e3a02..65ceeaa30652 100644 --- a/include/linux/proc_fs.h +++ b/include/linux/proc_fs.h @@ -139,15 +139,12 @@ extern void proc_tty_unregister_driver(struct tty_driver *driver); /* * proc_devtree.c */ +#ifdef CONFIG_PROC_DEVICETREE struct device_node; +struct property; extern void proc_device_tree_init(void); -#ifdef CONFIG_PROC_DEVICETREE extern void proc_device_tree_add_node(struct device_node *, struct proc_dir_entry *); -#else /* !CONFIG_PROC_DEVICETREE */ -static inline void proc_device_tree_add_node(struct device_node *np, struct proc_dir_entry *pde) -{ - return; -} +extern void proc_device_tree_add_prop(struct proc_dir_entry *pde, struct property *prop); #endif /* CONFIG_PROC_DEVICETREE */ extern struct proc_dir_entry *proc_symlink(const char *, |