1 files changed, 90 insertions, 0 deletions
diff --git a/include/linux/power/bq2415x_charger.h b/include/linux/power/bq2415x_charger.h
new file mode 100644
index 000000000000..fb6bf4d8aea8
--- /dev/null
+++ b/include/linux/power/bq2415x_charger.h
@@ -0,0 +1,90 @@
+/*
+    bq2415x_charger.h - bq2415x charger driver
+    Copyright (C) 2011-2012  Pali Rohár <pali.rohar@gmail.com>
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation; either version 2 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License along
+    with this program; if not, write to the Free Software Foundation, Inc.,
+    51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+*/
+
+#ifndef BQ2415X_CHARGER_H
+#define BQ2415X_CHARGER_H
+
+/*
+  This is platform data for bq2415x chip. It contains default board voltages
+  and currents which can be also later configured via sysfs. If value is -1
+  then default chip value (specified in datasheet) will be used.
+
+  Value resistor_sense is needed for for configuring charge and termination
+  current. It it is less or equal to zero, configuring charge and termination
+  current will not be possible.
+
+  Function set_mode_hook is needed for automode (setting correct current limit
+  when charger is connected/disconnected or setting boost mode). When is NULL,
+  automode function is disabled. When is not NULL, it must have this prototype:
+
+    int (*set_mode_hook)(
+      void (*hook)(enum bq2415x_mode mode, void *data),
+      void *data)
+
+  hook is hook function (see below) and data is pointer to driver private data
+
+  bq2415x driver will call it as:
+
+    platform_data->set_mode_hook(bq2415x_hook_function, bq2415x_device);
+
+  Board/platform function set_mode_hook return non zero value when hook
+  function was successful registered. Platform code should call that hook
+  function (which get from pointer, with data) every time when charger was
+  connected/disconnected or require to enable boost mode. bq2415x driver then
+  will set correct current limit, enable/disable charger or boost mode.
+
+  Hook function has this prototype:
+
+    void hook(enum bq2415x_mode mode, void *data);
+
+  mode is bq2415x mode (charger or boost)
+  data is pointer to driver private data (which get from set_charger_type_hook)
+
+  When bq driver is being unloaded, it call function:
+
+    platform_data->set_mode_hook(NULL, NULL);
+
+  (hook function and driver private data are NULL)
+
+  After that board/platform code must not call driver hook function! It is
+  possible that pointer to hook function will not be valid and calling will
+  cause undefined result.
+
+*/
+
+/* Supported modes with maximal current limit */
+enum bq2415x_mode {
+	BQ2415X_MODE_NONE,		/* unknown or no charger (100mA) */
+	BQ2415X_MODE_HOST_CHARGER,	/* usb host/hub charger (500mA) */
+	BQ2415X_MODE_DEDICATED_CHARGER, /* dedicated charger (unlimited) */
+	BQ2415X_MODE_BOOST,		/* boost mode (charging disabled) */
+};
+
+struct bq2415x_platform_data {
+	int current_limit;		/* mA */
+	int weak_battery_voltage;	/* mV */
+	int battery_regulation_voltage;	/* mV */
+	int charge_current;		/* mA */
+	int termination_current;	/* mA */
+	int resistor_sense;		/* m ohm */
+	int (*set_mode_hook)(void (*hook)(enum bq2415x_mode mode, void *data),
+			     void *data);
+};
+
+#endif