diff options
Diffstat (limited to 'include/uapi/linux/nl80211.h')
| -rw-r--r-- | include/uapi/linux/nl80211.h | 76 |
1 files changed, 70 insertions, 6 deletions
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index 56368e9b4622..6b76e3b0c18e 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -323,7 +323,7 @@ * @NL80211_CMD_GET_SCAN: get scan results * @NL80211_CMD_TRIGGER_SCAN: trigger a new scan with the given parameters * %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the - * probe requests at CCK rate or not. %NL80211_ATTR_MAC can be used to + * probe requests at CCK rate or not. %NL80211_ATTR_BSSID can be used to * specify a BSSID to scan for; if not included, the wildcard BSSID will * be used. * @NL80211_CMD_NEW_SCAN_RESULTS: scan notification (as a reply to @@ -600,6 +600,20 @@ * * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface. * + * @NL80211_CMD_SET_MULTICAST_TO_UNICAST: Configure if this AP should perform + * multicast to unicast conversion. When enabled, all multicast packets + * with ethertype ARP, IPv4 or IPv6 (possibly within an 802.1Q header) + * will be sent out to each station once with the destination (multicast) + * MAC address replaced by the station's MAC address. Note that this may + * break certain expectations of the receiver, e.g. the ability to drop + * unicast IP packets encapsulated in multicast L2 frames, or the ability + * to not send destination unreachable messages in such cases. + * This can only be toggled per BSS. Configure this on an interface of + * type %NL80211_IFTYPE_AP. It applies to all its VLAN interfaces + * (%NL80211_IFTYPE_AP_VLAN), except for those in 4addr (WDS) mode. + * If %NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED is not present with this + * command, the feature is disabled. + * * @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial * mesh config parameters may be given. * @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the @@ -874,6 +888,12 @@ * This will contain a %NL80211_ATTR_NAN_MATCH nested attribute and * %NL80211_ATTR_COOKIE. * + * @NL80211_CMD_UPDATE_CONNECT_PARAMS: Update one or more connect parameters + * for subsequent roaming cases if the driver or firmware uses internal + * BSS selection. This command can be issued only while connected and it + * does not result in a change for the current association. Currently, + * only the %NL80211_ATTR_IE data is used and updated with this command. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -1069,6 +1089,10 @@ enum nl80211_commands { NL80211_CMD_CHANGE_NAN_CONFIG, NL80211_CMD_NAN_MATCH, + NL80211_CMD_SET_MULTICAST_TO_UNICAST, + + NL80211_CMD_UPDATE_CONNECT_PARAMS, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -1638,8 +1662,16 @@ enum nl80211_commands { * the connection request from a station. nl80211_connect_failed_reason * enum has different reasons of connection failure. * - * @NL80211_ATTR_SAE_DATA: SAE elements in Authentication frames. This starts - * with the Authentication transaction sequence number field. + * @NL80211_ATTR_AUTH_DATA: Fields and elements in Authentication frames. + * This contains the authentication frame body (non-IE and IE data), + * excluding the Authentication algorithm number, i.e., starting at the + * Authentication transaction sequence number field. It is used with + * authentication algorithms that need special fields to be added into + * the frames (SAE and FILS). Currently, only the SAE cases use the + * initial two fields (Authentication transaction sequence number and + * Status code). However, those fields are included in the attribute data + * for all authentication algorithms to keep the attribute definition + * consistent. * * @NL80211_ATTR_VHT_CAPABILITY: VHT Capability information element (from * association request when used with NL80211_CMD_NEW_STATION) @@ -1936,6 +1968,17 @@ enum nl80211_commands { * attribute. * @NL80211_ATTR_NAN_MATCH: used to report a match. This is a nested attribute. * See &enum nl80211_nan_match_attributes. + * @NL80211_ATTR_FILS_KEK: KEK for FILS (Re)Association Request/Response frame + * protection. + * @NL80211_ATTR_FILS_NONCES: Nonces (part of AAD) for FILS (Re)Association + * Request/Response frame protection. This attribute contains the 16 octet + * STA Nonce followed by 16 octets of AP Nonce. + * + * @NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED: Indicates whether or not multicast + * packets should be send out as unicast to all stations (flag attribute). + * + * @NL80211_ATTR_BSSID: The BSSID of the AP. Note that %NL80211_ATTR_MAC is also + * used in various commands/events for specifying the BSSID. * * @NUM_NL80211_ATTR: total number of nl80211_attrs available * @NL80211_ATTR_MAX: highest attribute number currently defined @@ -2195,7 +2238,7 @@ enum nl80211_attrs { NL80211_ATTR_CONN_FAILED_REASON, - NL80211_ATTR_SAE_DATA, + NL80211_ATTR_AUTH_DATA, NL80211_ATTR_VHT_CAPABILITY, @@ -2336,6 +2379,13 @@ enum nl80211_attrs { NL80211_ATTR_NAN_FUNC, NL80211_ATTR_NAN_MATCH, + NL80211_ATTR_FILS_KEK, + NL80211_ATTR_FILS_NONCES, + + NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED, + + NL80211_ATTR_BSSID, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -2347,6 +2397,7 @@ enum nl80211_attrs { #define NL80211_ATTR_SCAN_GENERATION NL80211_ATTR_GENERATION #define NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG #define NL80211_ATTR_IFACE_SOCKET_OWNER NL80211_ATTR_SOCKET_OWNER +#define NL80211_ATTR_SAE_DATA NL80211_ATTR_AUTH_DATA /* * Allow user space programs to use #ifdef on new attributes by defining them @@ -3660,6 +3711,9 @@ enum nl80211_bss_status { * @NL80211_AUTHTYPE_FT: Fast BSS Transition (IEEE 802.11r) * @NL80211_AUTHTYPE_NETWORK_EAP: Network EAP (some Cisco APs and mainly LEAP) * @NL80211_AUTHTYPE_SAE: Simultaneous authentication of equals + * @NL80211_AUTHTYPE_FILS_SK: Fast Initial Link Setup shared key + * @NL80211_AUTHTYPE_FILS_SK_PFS: Fast Initial Link Setup shared key with PFS + * @NL80211_AUTHTYPE_FILS_PK: Fast Initial Link Setup public key * @__NL80211_AUTHTYPE_NUM: internal * @NL80211_AUTHTYPE_MAX: maximum valid auth algorithm * @NL80211_AUTHTYPE_AUTOMATIC: determine automatically (if necessary by @@ -3672,6 +3726,9 @@ enum nl80211_auth_type { NL80211_AUTHTYPE_FT, NL80211_AUTHTYPE_NETWORK_EAP, NL80211_AUTHTYPE_SAE, + NL80211_AUTHTYPE_FILS_SK, + NL80211_AUTHTYPE_FILS_SK_PFS, + NL80211_AUTHTYPE_FILS_PK, /* keep last */ __NL80211_AUTHTYPE_NUM, @@ -4280,6 +4337,9 @@ enum nl80211_iface_limit_attrs { * of supported channel widths for radar detection. * @NL80211_IFACE_COMB_RADAR_DETECT_REGIONS: u32 attribute containing the bitmap * of supported regulatory regions for radar detection. + * @NL80211_IFACE_COMB_BI_MIN_GCD: u32 attribute specifying the minimum GCD of + * different beacon intervals supported by all the interface combinations + * in this group (if not present, all beacon intervals be identical). * @NUM_NL80211_IFACE_COMB: number of attributes * @MAX_NL80211_IFACE_COMB: highest attribute number * @@ -4287,8 +4347,8 @@ enum nl80211_iface_limit_attrs { * limits = [ #{STA} <= 1, #{AP} <= 1 ], matching BI, channels = 1, max = 2 * => allows an AP and a STA that must match BIs * - * numbers = [ #{AP, P2P-GO} <= 8 ], channels = 1, max = 8 - * => allows 8 of AP/GO + * numbers = [ #{AP, P2P-GO} <= 8 ], BI min gcd, channels = 1, max = 8, + * => allows 8 of AP/GO that can have BI gcd >= min gcd * * numbers = [ #{STA} <= 2 ], channels = 2, max = 2 * => allows two STAs on different channels @@ -4314,6 +4374,7 @@ enum nl80211_if_combination_attrs { NL80211_IFACE_COMB_NUM_CHANNELS, NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS, NL80211_IFACE_COMB_RADAR_DETECT_REGIONS, + NL80211_IFACE_COMB_BI_MIN_GCD, /* keep last */ NUM_NL80211_IFACE_COMB, @@ -4634,6 +4695,8 @@ enum nl80211_feature_flags { * configuration (AP/mesh) with HT rates. * @NL80211_EXT_FEATURE_BEACON_RATE_VHT: Driver supports beacon rate * configuration (AP/mesh) with VHT rates. + * @NL80211_EXT_FEATURE_FILS_STA: This driver supports Fast Initial Link Setup + * with user space SME (NL80211_CMD_AUTHENTICATE) in station mode. * * @NUM_NL80211_EXT_FEATURES: number of extended features. * @MAX_NL80211_EXT_FEATURES: highest extended feature index. @@ -4648,6 +4711,7 @@ enum nl80211_ext_feature_index { NL80211_EXT_FEATURE_BEACON_RATE_LEGACY, NL80211_EXT_FEATURE_BEACON_RATE_HT, NL80211_EXT_FEATURE_BEACON_RATE_VHT, + NL80211_EXT_FEATURE_FILS_STA, /* add new features before the definition below */ NUM_NL80211_EXT_FEATURES, |