diff options
Diffstat (limited to 'include/linux')
25 files changed, 2360 insertions, 223 deletions
diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h index a12a38107c1a..1faa58f9b85e 100644 --- a/include/linux/i2c/twl.h +++ b/include/linux/i2c/twl.h @@ -188,6 +188,7 @@ int twl_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes); int twl_get_type(void); int twl_get_version(void); +int twl_get_hfclk_rate(void); int twl6030_interrupt_unmask(u8 bit_mask, u8 offset); int twl6030_interrupt_mask(u8 bit_mask, u8 offset); diff --git a/include/linux/ioport.h b/include/linux/ioport.h index 589e0e75efae..85ac9b9b72a2 100644 --- a/include/linux/ioport.h +++ b/include/linux/ioport.h @@ -29,8 +29,9 @@ struct resource { #define IORESOURCE_BITS 0x000000ff /* Bus-specific bits */ #define IORESOURCE_TYPE_BITS 0x00001f00 /* Resource type */ -#define IORESOURCE_IO 0x00000100 +#define IORESOURCE_IO 0x00000100 /* PCI/ISA I/O ports */ #define IORESOURCE_MEM 0x00000200 +#define IORESOURCE_REG 0x00000300 /* Register offsets */ #define IORESOURCE_IRQ 0x00000400 #define IORESOURCE_DMA 0x00000800 #define IORESOURCE_BUS 0x00001000 diff --git a/include/linux/mfd/88pm860x.h b/include/linux/mfd/88pm860x.h index 7b24943779fa..ef3e6b701179 100644 --- a/include/linux/mfd/88pm860x.h +++ b/include/linux/mfd/88pm860x.h @@ -34,22 +34,6 @@ enum { PM8606_ID_MAX, }; -enum { - PM8606_BACKLIGHT1 = 0, - PM8606_BACKLIGHT2, - PM8606_BACKLIGHT3, -}; - -enum { - PM8606_LED1_RED = 0, - PM8606_LED1_GREEN, - PM8606_LED1_BLUE, - PM8606_LED2_RED, - PM8606_LED2_GREEN, - PM8606_LED2_BLUE, - PM8607_LED_VIBRATOR, -}; - /* 8606 Registers */ #define PM8606_DCM_BOOST (0x00) @@ -322,7 +306,7 @@ struct pm860x_chip { struct regmap *regmap_companion; int buck3_double; /* DVC ramp slope double */ - unsigned short companion_addr; + int companion_addr; unsigned short osc_vote; int id; int irq_mode; @@ -340,16 +324,12 @@ enum { }; struct pm860x_backlight_pdata { - int id; int pwm; int iset; - unsigned long flags; }; struct pm860x_led_pdata { - int id; int iset; - unsigned long flags; }; struct pm860x_rtc_pdata { @@ -379,15 +359,29 @@ struct pm860x_platform_data { struct pm860x_rtc_pdata *rtc; struct pm860x_touch_pdata *touch; struct pm860x_power_pdata *power; - struct regulator_init_data *regulator; - - unsigned short companion_addr; /* I2C address of companion chip */ + struct regulator_init_data *buck1; + struct regulator_init_data *buck2; + struct regulator_init_data *buck3; + struct regulator_init_data *ldo1; + struct regulator_init_data *ldo2; + struct regulator_init_data *ldo3; + struct regulator_init_data *ldo4; + struct regulator_init_data *ldo5; + struct regulator_init_data *ldo6; + struct regulator_init_data *ldo7; + struct regulator_init_data *ldo8; + struct regulator_init_data *ldo9; + struct regulator_init_data *ldo10; + struct regulator_init_data *ldo12; + struct regulator_init_data *ldo_vibrator; + struct regulator_init_data *ldo14; + + int companion_addr; /* I2C address of companion chip */ int i2c_port; /* Controlled by GI2C or PI2C */ int irq_mode; /* Clear interrupt by read/write(0/1) */ int irq_base; /* IRQ base number of 88pm860x */ int num_leds; int num_backlights; - int num_regulators; }; extern int pm8606_osc_enable(struct pm860x_chip *, unsigned short); @@ -408,8 +402,4 @@ extern int pm860x_page_bulk_write(struct i2c_client *, int, int, extern int pm860x_page_set_bits(struct i2c_client *, int, unsigned char, unsigned char); -extern int pm860x_device_init(struct pm860x_chip *chip, - struct pm860x_platform_data *pdata) __devinit ; -extern void pm860x_device_exit(struct pm860x_chip *chip) __devexit ; - #endif /* __LINUX_MFD_88PM860X_H */ diff --git a/include/linux/mfd/ab3100.h b/include/linux/mfd/ab3100.h new file mode 100644 index 000000000000..afd3080bde24 --- /dev/null +++ b/include/linux/mfd/ab3100.h @@ -0,0 +1,129 @@ +/* + * Copyright (C) 2007-2009 ST-Ericsson AB + * License terms: GNU General Public License (GPL) version 2 + * AB3100 core access functions + * Author: Linus Walleij <linus.walleij@stericsson.com> + * + */ + +#include <linux/regulator/machine.h> + +struct device; + +#ifndef MFD_AB3100_H +#define MFD_AB3100_H + + +#define AB3100_P1A 0xc0 +#define AB3100_P1B 0xc1 +#define AB3100_P1C 0xc2 +#define AB3100_P1D 0xc3 +#define AB3100_P1E 0xc4 +#define AB3100_P1F 0xc5 +#define AB3100_P1G 0xc6 +#define AB3100_R2A 0xc7 +#define AB3100_R2B 0xc8 + +/* + * AB3100, EVENTA1, A2 and A3 event register flags + * these are catenated into a single 32-bit flag in the code + * for event notification broadcasts. + */ +#define AB3100_EVENTA1_ONSWA (0x01<<16) +#define AB3100_EVENTA1_ONSWB (0x02<<16) +#define AB3100_EVENTA1_ONSWC (0x04<<16) +#define AB3100_EVENTA1_DCIO (0x08<<16) +#define AB3100_EVENTA1_OVER_TEMP (0x10<<16) +#define AB3100_EVENTA1_SIM_OFF (0x20<<16) +#define AB3100_EVENTA1_VBUS (0x40<<16) +#define AB3100_EVENTA1_VSET_USB (0x80<<16) + +#define AB3100_EVENTA2_READY_TX (0x01<<8) +#define AB3100_EVENTA2_READY_RX (0x02<<8) +#define AB3100_EVENTA2_OVERRUN_ERROR (0x04<<8) +#define AB3100_EVENTA2_FRAMING_ERROR (0x08<<8) +#define AB3100_EVENTA2_CHARG_OVERCURRENT (0x10<<8) +#define AB3100_EVENTA2_MIDR (0x20<<8) +#define AB3100_EVENTA2_BATTERY_REM (0x40<<8) +#define AB3100_EVENTA2_ALARM (0x80<<8) + +#define AB3100_EVENTA3_ADC_TRIG5 (0x01) +#define AB3100_EVENTA3_ADC_TRIG4 (0x02) +#define AB3100_EVENTA3_ADC_TRIG3 (0x04) +#define AB3100_EVENTA3_ADC_TRIG2 (0x08) +#define AB3100_EVENTA3_ADC_TRIGVBAT (0x10) +#define AB3100_EVENTA3_ADC_TRIGVTX (0x20) +#define AB3100_EVENTA3_ADC_TRIG1 (0x40) +#define AB3100_EVENTA3_ADC_TRIG0 (0x80) + +/* AB3100, STR register flags */ +#define AB3100_STR_ONSWA (0x01) +#define AB3100_STR_ONSWB (0x02) +#define AB3100_STR_ONSWC (0x04) +#define AB3100_STR_DCIO (0x08) +#define AB3100_STR_BOOT_MODE (0x10) +#define AB3100_STR_SIM_OFF (0x20) +#define AB3100_STR_BATT_REMOVAL (0x40) +#define AB3100_STR_VBUS (0x80) + +/* + * AB3100 contains 8 regulators, one external regulator controller + * and a buck converter, further the LDO E and buck converter can + * have separate settings if they are in sleep mode, this is + * modeled as a separate regulator. + */ +#define AB3100_NUM_REGULATORS 10 + +/** + * struct ab3100 + * @access_mutex: lock out concurrent accesses to the AB3100 registers + * @dev: pointer to the containing device + * @i2c_client: I2C client for this chip + * @testreg_client: secondary client for test registers + * @chip_name: name of this chip variant + * @chip_id: 8 bit chip ID for this chip variant + * @event_subscribers: event subscribers are listed here + * @startup_events: a copy of the first reading of the event registers + * @startup_events_read: whether the first events have been read + * + * This struct is PRIVATE and devices using it should NOT + * access ANY fields. It is used as a token for calling the + * AB3100 functions. + */ +struct ab3100 { + struct mutex access_mutex; + struct device *dev; + struct i2c_client *i2c_client; + struct i2c_client *testreg_client; + char chip_name[32]; + u8 chip_id; + struct blocking_notifier_head event_subscribers; + u8 startup_events[3]; + bool startup_events_read; +}; + +/** + * struct ab3100_platform_data + * Data supplied to initialize board connections to the AB3100 + * @reg_constraints: regulator constraints for target board + * the order of these constraints are: LDO A, C, D, E, + * F, G, H, K, EXT and BUCK. + * @reg_initvals: initial values for the regulator registers + * plus two sleep settings for LDO E and the BUCK converter. + * exactly AB3100_NUM_REGULATORS+2 values must be sent in. + * Order: LDO A, C, E, E sleep, F, G, H, K, EXT, BUCK, + * BUCK sleep, LDO D. (LDO D need to be initialized last.) + * @external_voltage: voltage level of the external regulator. + */ +struct ab3100_platform_data { + struct regulator_init_data reg_constraints[AB3100_NUM_REGULATORS]; + u8 reg_initvals[AB3100_NUM_REGULATORS+2]; + int external_voltage; +}; + +int ab3100_event_register(struct ab3100 *ab3100, + struct notifier_block *nb); +int ab3100_event_unregister(struct ab3100 *ab3100, + struct notifier_block *nb); + +#endif /* MFD_AB3100_H */ diff --git a/include/linux/mfd/abx500.h b/include/linux/mfd/abx500.h index 1318ca622633..5d5298d56026 100644 --- a/include/linux/mfd/abx500.h +++ b/include/linux/mfd/abx500.h @@ -1,12 +1,9 @@ /* * Copyright (C) 2007-2009 ST-Ericsson AB * License terms: GNU General Public License (GPL) version 2 - * AB3100 core access functions - * Author: Linus Walleij <linus.walleij@stericsson.com> * * ABX500 core access functions. - * The abx500 interface is used for the Analog Baseband chip - * ab3100 and ab8500. + * The abx500 interface is used for the Analog Baseband chips. * * Author: Mattias Wallin <mattias.wallin@stericsson.com> * Author: Mattias Nilsson <mattias.i.nilsson@stericsson.com> @@ -21,118 +18,6 @@ struct device; #ifndef MFD_ABX500_H #define MFD_ABX500_H -#define AB3100_P1A 0xc0 -#define AB3100_P1B 0xc1 -#define AB3100_P1C 0xc2 -#define AB3100_P1D 0xc3 -#define AB3100_P1E 0xc4 -#define AB3100_P1F 0xc5 -#define AB3100_P1G 0xc6 -#define AB3100_R2A 0xc7 -#define AB3100_R2B 0xc8 - -/* - * AB3100, EVENTA1, A2 and A3 event register flags - * these are catenated into a single 32-bit flag in the code - * for event notification broadcasts. - */ -#define AB3100_EVENTA1_ONSWA (0x01<<16) -#define AB3100_EVENTA1_ONSWB (0x02<<16) -#define AB3100_EVENTA1_ONSWC (0x04<<16) -#define AB3100_EVENTA1_DCIO (0x08<<16) -#define AB3100_EVENTA1_OVER_TEMP (0x10<<16) -#define AB3100_EVENTA1_SIM_OFF (0x20<<16) -#define AB3100_EVENTA1_VBUS (0x40<<16) -#define AB3100_EVENTA1_VSET_USB (0x80<<16) - -#define AB3100_EVENTA2_READY_TX (0x01<<8) -#define AB3100_EVENTA2_READY_RX (0x02<<8) -#define AB3100_EVENTA2_OVERRUN_ERROR (0x04<<8) -#define AB3100_EVENTA2_FRAMING_ERROR (0x08<<8) -#define AB3100_EVENTA2_CHARG_OVERCURRENT (0x10<<8) -#define AB3100_EVENTA2_MIDR (0x20<<8) -#define AB3100_EVENTA2_BATTERY_REM (0x40<<8) -#define AB3100_EVENTA2_ALARM (0x80<<8) - -#define AB3100_EVENTA3_ADC_TRIG5 (0x01) -#define AB3100_EVENTA3_ADC_TRIG4 (0x02) -#define AB3100_EVENTA3_ADC_TRIG3 (0x04) -#define AB3100_EVENTA3_ADC_TRIG2 (0x08) -#define AB3100_EVENTA3_ADC_TRIGVBAT (0x10) -#define AB3100_EVENTA3_ADC_TRIGVTX (0x20) -#define AB3100_EVENTA3_ADC_TRIG1 (0x40) -#define AB3100_EVENTA3_ADC_TRIG0 (0x80) - -/* AB3100, STR register flags */ -#define AB3100_STR_ONSWA (0x01) -#define AB3100_STR_ONSWB (0x02) -#define AB3100_STR_ONSWC (0x04) -#define AB3100_STR_DCIO (0x08) -#define AB3100_STR_BOOT_MODE (0x10) -#define AB3100_STR_SIM_OFF (0x20) -#define AB3100_STR_BATT_REMOVAL (0x40) -#define AB3100_STR_VBUS (0x80) - -/* - * AB3100 contains 8 regulators, one external regulator controller - * and a buck converter, further the LDO E and buck converter can - * have separate settings if they are in sleep mode, this is - * modeled as a separate regulator. - */ -#define AB3100_NUM_REGULATORS 10 - -/** - * struct ab3100 - * @access_mutex: lock out concurrent accesses to the AB3100 registers - * @dev: pointer to the containing device - * @i2c_client: I2C client for this chip - * @testreg_client: secondary client for test registers - * @chip_name: name of this chip variant - * @chip_id: 8 bit chip ID for this chip variant - * @event_subscribers: event subscribers are listed here - * @startup_events: a copy of the first reading of the event registers - * @startup_events_read: whether the first events have been read - * - * This struct is PRIVATE and devices using it should NOT - * access ANY fields. It is used as a token for calling the - * AB3100 functions. - */ -struct ab3100 { - struct mutex access_mutex; - struct device *dev; - struct i2c_client *i2c_client; - struct i2c_client *testreg_client; - char chip_name[32]; - u8 chip_id; - struct blocking_notifier_head event_subscribers; - u8 startup_events[3]; - bool startup_events_read; -}; - -/** - * struct ab3100_platform_data - * Data supplied to initialize board connections to the AB3100 - * @reg_constraints: regulator constraints for target board - * the order of these constraints are: LDO A, C, D, E, - * F, G, H, K, EXT and BUCK. - * @reg_initvals: initial values for the regulator registers - * plus two sleep settings for LDO E and the BUCK converter. - * exactly AB3100_NUM_REGULATORS+2 values must be sent in. - * Order: LDO A, C, E, E sleep, F, G, H, K, EXT, BUCK, - * BUCK sleep, LDO D. (LDO D need to be initialized last.) - * @external_voltage: voltage level of the external regulator. - */ -struct ab3100_platform_data { - struct regulator_init_data reg_constraints[AB3100_NUM_REGULATORS]; - u8 reg_initvals[AB3100_NUM_REGULATORS+2]; - int external_voltage; -}; - -int ab3100_event_register(struct ab3100 *ab3100, - struct notifier_block *nb); -int ab3100_event_unregister(struct ab3100 *ab3100, - struct notifier_block *nb); - /** * struct abx500_init_setting * Initial value of the registers for driver to use during setup. diff --git a/include/linux/mfd/abx500/ab8500.h b/include/linux/mfd/abx500/ab8500.h index 3764cb6759e3..1491044efa10 100644 --- a/include/linux/mfd/abx500/ab8500.h +++ b/include/linux/mfd/abx500/ab8500.h @@ -341,6 +341,4 @@ static inline int is_ab8500_2p0(struct ab8500 *ab) return (is_ab8500(ab) && (ab->chip_id == AB8500_CUT2P0)); } -int ab8500_irq_get_virq(struct ab8500 *ab8500, int irq); - #endif /* MFD_AB8500_H */ diff --git a/include/linux/mfd/anatop.h b/include/linux/mfd/anatop.h deleted file mode 100644 index 7f92acf03d9e..000000000000 --- a/include/linux/mfd/anatop.h +++ /dev/null @@ -1,40 +0,0 @@ -/* - * anatop.h - Anatop MFD driver - * - * Copyright (C) 2012 Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org> - * Copyright (C) 2012 Linaro - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef __LINUX_MFD_ANATOP_H -#define __LINUX_MFD_ANATOP_H - -#include <linux/spinlock.h> - -/** - * anatop - MFD data - * @ioreg: ioremap register - * @reglock: spinlock for register read/write - */ -struct anatop { - void *ioreg; - spinlock_t reglock; -}; - -extern u32 anatop_read_reg(struct anatop *, u32); -extern void anatop_write_reg(struct anatop *, u32, u32, u32); - -#endif /* __LINUX_MFD_ANATOP_H */ diff --git a/include/linux/mfd/da9055/core.h b/include/linux/mfd/da9055/core.h new file mode 100644 index 000000000000..c96ad682c59e --- /dev/null +++ b/include/linux/mfd/da9055/core.h @@ -0,0 +1,94 @@ +/* + * da9055 declarations for DA9055 PMICs. + * + * Copyright(c) 2012 Dialog Semiconductor Ltd. + * + * Author: David Dajun Chen <dchen@diasemi.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ + +#ifndef __DA9055_CORE_H +#define __DA9055_CORE_H + +#include <linux/interrupt.h> +#include <linux/regmap.h> + +/* + * PMIC IRQ + */ +#define DA9055_IRQ_ALARM 0x01 +#define DA9055_IRQ_TICK 0x02 +#define DA9055_IRQ_NONKEY 0x00 +#define DA9055_IRQ_REGULATOR 0x0B +#define DA9055_IRQ_HWMON 0x03 + +struct da9055_pdata; + +struct da9055 { + struct regmap *regmap; + struct regmap_irq_chip_data *irq_data; + struct device *dev; + struct i2c_client *i2c_client; + + int irq_base; + int chip_irq; +}; + +/* Device I/O */ +static inline int da9055_reg_read(struct da9055 *da9055, unsigned char reg) +{ + int val, ret; + + ret = regmap_read(da9055->regmap, reg, &val); + if (ret < 0) + return ret; + + return val; +} + +static inline int da9055_reg_write(struct da9055 *da9055, unsigned char reg, + unsigned char val) +{ + return regmap_write(da9055->regmap, reg, val); +} + +static inline int da9055_group_read(struct da9055 *da9055, unsigned char reg, + unsigned reg_cnt, unsigned char *val) +{ + return regmap_bulk_read(da9055->regmap, reg, val, reg_cnt); +} + +static inline int da9055_group_write(struct da9055 *da9055, unsigned char reg, + unsigned reg_cnt, unsigned char *val) +{ + return regmap_raw_write(da9055->regmap, reg, val, reg_cnt); +} + +static inline int da9055_reg_update(struct da9055 *da9055, unsigned char reg, + unsigned char bit_mask, + unsigned char reg_val) +{ + return regmap_update_bits(da9055->regmap, reg, bit_mask, reg_val); +} + +/* Generic Device API */ +int da9055_device_init(struct da9055 *da9055); +void da9055_device_exit(struct da9055 *da9055); + +extern struct regmap_config da9055_regmap_config; + +#endif /* __DA9055_CORE_H */ diff --git a/include/linux/mfd/da9055/pdata.h b/include/linux/mfd/da9055/pdata.h new file mode 100644 index 000000000000..147293b4471d --- /dev/null +++ b/include/linux/mfd/da9055/pdata.h @@ -0,0 +1,32 @@ +/* Copyright (C) 2012 Dialog Semiconductor Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ +#ifndef __DA9055_PDATA_H +#define __DA9055_PDATA_H + +#define DA9055_MAX_REGULATORS 8 + +struct da9055; + +enum gpio_select { + NO_GPIO = 0, + GPIO_1, + GPIO_2 +}; + +struct da9055_pdata { + int (*init) (struct da9055 *da9055); + int irq_base; + int gpio_base; + + struct regulator_init_data *regulators[DA9055_MAX_REGULATORS]; + bool reset_enable; /* Enable RTC in RESET Mode */ + enum gpio_select *gpio_rsel; /* Select regulator set thru GPIO 1/2 */ + enum gpio_select *gpio_ren; /* Enable regulator thru GPIO 1/2 */ +}; +#endif /* __DA9055_PDATA_H */ diff --git a/include/linux/mfd/da9055/reg.h b/include/linux/mfd/da9055/reg.h new file mode 100644 index 000000000000..df237ee54803 --- /dev/null +++ b/include/linux/mfd/da9055/reg.h @@ -0,0 +1,699 @@ +/* + * DA9055 declarations for DA9055 PMICs. + * + * Copyright(c) 2012 Dialog Semiconductor Ltd. + * + * Author: David Dajun Chen <dchen@diasemi.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ + +#ifndef __DA9055_REG_H +#define __DA9055_REG_H + +/* + * PMIC registers + */ + /* PAGE0 */ +#define DA9055_REG_PAGE_CON 0x00 + +/* System Control and Event Registers */ +#define DA9055_REG_STATUS_A 0x01 +#define DA9055_REG_STATUS_B 0x02 +#define DA9055_REG_FAULT_LOG 0x03 +#define DA9055_REG_EVENT_A 0x04 +#define DA9055_REG_EVENT_B 0x05 +#define DA9055_REG_EVENT_C 0x06 +#define DA9055_REG_IRQ_MASK_A 0x07 +#define DA9055_REG_IRQ_MASK_B 0x08 +#define DA9055_REG_IRQ_MASK_C 0x09 +#define DA9055_REG_CONTROL_A 0x0A +#define DA9055_REG_CONTROL_B 0x0B +#define DA9055_REG_CONTROL_C 0x0C +#define DA9055_REG_CONTROL_D 0x0D +#define DA9055_REG_CONTROL_E 0x0E +#define DA9055_REG_PD_DIS 0x0F + +/* GPIO Control Registers */ +#define DA9055_REG_GPIO0_1 0x10 +#define DA9055_REG_GPIO2 0x11 +#define DA9055_REG_GPIO_MODE0_2 0x12 + +/* Regulator Control Registers */ +#define DA9055_REG_BCORE_CONT 0x13 +#define DA9055_REG_BMEM_CONT 0x14 +#define DA9055_REG_LDO1_CONT 0x15 +#define DA9055_REG_LDO2_CONT 0x16 +#define DA9055_REG_LDO3_CONT 0x17 +#define DA9055_REG_LDO4_CONT 0x18 +#define DA9055_REG_LDO5_CONT 0x19 +#define DA9055_REG_LDO6_CONT 0x1A + +/* GP-ADC Control Registers */ +#define DA9055_REG_ADC_MAN 0x1B +#define DA9055_REG_ADC_CONT 0x1C +#define DA9055_REG_VSYS_MON 0x1D +#define DA9055_REG_ADC_RES_L 0x1E +#define DA9055_REG_ADC_RES_H 0x1F +#define DA9055_REG_VSYS_RES 0x20 +#define DA9055_REG_ADCIN1_RES 0x21 +#define DA9055_REG_ADCIN2_RES 0x22 +#define DA9055_REG_ADCIN3_RES 0x23 + +/* Sequencer Control Registers */ +#define DA9055_REG_EN_32K 0x35 + +/* Regulator Setting Registers */ +#define DA9055_REG_BUCK_LIM 0x37 +#define DA9055_REG_BCORE_MODE 0x38 +#define DA9055_REG_VBCORE_A 0x39 +#define DA9055_REG_VBMEM_A 0x3A +#define DA9055_REG_VLDO1_A 0x3B +#define DA9055_REG_VLDO2_A 0x3C +#define DA9055_REG_VLDO3_A 0x3D +#define DA9055_REG_VLDO4_A 0x3E +#define DA9055_REG_VLDO5_A 0x3F +#define DA9055_REG_VLDO6_A 0x40 +#define DA9055_REG_VBCORE_B 0x41 +#define DA9055_REG_VBMEM_B 0x42 +#define DA9055_REG_VLDO1_B 0x43 +#define DA9055_REG_VLDO2_B 0x44 +#define DA9055_REG_VLDO3_B 0x45 +#define DA9055_REG_VLDO4_B 0x46 +#define DA9055_REG_VLDO5_B 0x47 +#define DA9055_REG_VLDO6_B 0x48 + +/* GP-ADC Threshold Registers */ +#define DA9055_REG_AUTO1_HIGH 0x49 +#define DA9055_REG_AUTO1_LOW 0x4A +#define DA9055_REG_AUTO2_HIGH 0x4B +#define DA9055_REG_AUTO2_LOW 0x4C +#define DA9055_REG_AUTO3_HIGH 0x4D +#define DA9055_REG_AUTO3_LOW 0x4E + +/* OTP */ +#define DA9055_REG_OPT_COUNT 0x50 +#define DA9055_REG_OPT_ADDR 0x51 +#define DA9055_REG_OPT_DATA 0x52 + +/* RTC Calendar and Alarm Registers */ +#define DA9055_REG_COUNT_S 0x53 +#define DA9055_REG_COUNT_MI 0x54 +#define DA9055_REG_COUNT_H 0x55 +#define DA9055_REG_COUNT_D 0x56 +#define DA9055_REG_COUNT_MO 0x57 +#define DA9055_REG_COUNT_Y 0x58 +#define DA9055_REG_ALARM_MI 0x59 +#define DA9055_REG_ALARM_H 0x5A +#define DA9055_REG_ALARM_D 0x5B +#define DA9055_REG_ALARM_MO 0x5C +#define DA9055_REG_ALARM_Y 0x5D +#define DA9055_REG_SECOND_A 0x5E +#define DA9055_REG_SECOND_B 0x5F +#define DA9055_REG_SECOND_C 0x60 +#define DA9055_REG_SECOND_D 0x61 + +/* Customer Trim and Configuration */ +#define DA9055_REG_T_OFFSET 0x63 +#define DA9055_REG_INTERFACE 0x64 +#define DA9055_REG_CONFIG_A 0x65 +#define DA9055_REG_CONFIG_B 0x66 +#define DA9055_REG_CONFIG_C 0x67 +#define DA9055_REG_CONFIG_D 0x68 +#define DA9055_REG_CONFIG_E 0x69 +#define DA9055_REG_TRIM_CLDR 0x6F + +/* General Purpose Registers */ +#define DA9055_REG_GP_ID_0 0x70 +#define DA9055_REG_GP_ID_1 0x71 +#define DA9055_REG_GP_ID_2 0x72 +#define DA9055_REG_GP_ID_3 0x73 +#define DA9055_REG_GP_ID_4 0x74 +#define DA9055_REG_GP_ID_5 0x75 +#define DA9055_REG_GP_ID_6 0x76 +#define DA9055_REG_GP_ID_7 0x77 +#define DA9055_REG_GP_ID_8 0x78 +#define DA9055_REG_GP_ID_9 0x79 +#define DA9055_REG_GP_ID_10 0x7A +#define DA9055_REG_GP_ID_11 0x7B +#define DA9055_REG_GP_ID_12 0x7C +#define DA9055_REG_GP_ID_13 0x7D +#define DA9055_REG_GP_ID_14 0x7E +#define DA9055_REG_GP_ID_15 0x7F +#define DA9055_REG_GP_ID_16 0x80 +#define DA9055_REG_GP_ID_17 0x81 +#define DA9055_REG_GP_ID_18 0x82 +#define DA9055_REG_GP_ID_19 0x83 + +#define DA9055_MAX_REGISTER_CNT DA9055_REG_GP_ID_19 + +/* + * PMIC registers bits + */ + +/* DA9055_REG_PAGE_CON (addr=0x00) */ +#define DA9055_PAGE_WRITE_MODE (0<<6) +#define DA9055_REPEAT_WRITE_MODE (1<<6) + +/* DA9055_REG_STATUS_A (addr=0x01) */ +#define DA9055_NOKEY_STS 0x01 +#define DA9055_WAKE_STS 0x02 +#define DA9055_DVC_BUSY_STS 0x04 +#define DA9055_COMP1V2_STS 0x08 +#define DA9055_NJIG_STS 0x10 +#define DA9055_LDO5_LIM_STS 0x20 +#define DA9055_LDO6_LIM_STS 0x40 + +/* DA9055_REG_STATUS_B (addr=0x02) */ +#define DA9055_GPI0_STS 0x01 +#define DA9055_GPI1_STS 0x02 +#define DA9055_GPI2_STS 0x04 + +/* DA9055_REG_FAULT_LOG (addr=0x03) */ +#define DA9055_TWD_ERROR_FLG 0x01 +#define DA9055_POR_FLG 0x02 +#define DA9055_VDD_FAULT_FLG 0x04 +#define DA9055_VDD_START_FLG 0x08 +#define DA9055_TEMP_CRIT_FLG 0x10 +#define DA9055_KEY_RESET_FLG 0x20 +#define DA9055_WAIT_SHUT_FLG 0x80 + +/* DA9055_REG_EVENT_A (addr=0x04) */ +#define DA9055_NOKEY_EINT 0x01 +#define DA9055_ALARM_EINT 0x02 +#define DA9055_TICK_EINT 0x04 +#define DA9055_ADC_RDY_EINT 0x08 +#define DA9055_SEQ_RDY_EINT 0x10 +#define DA9055_EVENTS_B_EINT 0x20 +#define DA9055_EVENTS_C_EINT 0x40 + +/* DA9055_REG_EVENT_B (addr=0x05) */ +#define DA9055_E_WAKE_EINT 0x01 +#define DA9055_E_TEMP_EINT 0x02 +#define DA9055_E_COMP1V2_EINT 0x04 +#define DA9055_E_LDO_LIM_EINT 0x08 +#define DA9055_E_NJIG_EINT 0x20 +#define DA9055_E_VDD_MON_EINT 0x40 +#define DA9055_E_VDD_WARN_EINT 0x80 + +/* DA9055_REG_EVENT_C (addr=0x06) */ +#define DA9055_E_GPI0_EINT 0x01 +#define DA9055_E_GPI1_EINT 0x02 +#define DA9055_E_GPI2_EINT 0x04 + +/* DA9055_REG_IRQ_MASK_A (addr=0x07) */ +#define DA9055_M_NONKEY_EINT 0x01 +#define DA9055_M_ALARM_EINT 0x02 +#define DA9055_M_TICK_EINT 0x04 +#define DA9055_M_ADC_RDY_EINT 0x08 +#define DA9055_M_SEQ_RDY_EINT 0x10 + +/* DA9055_REG_IRQ_MASK_B (addr=0x08) */ +#define DA9055_M_WAKE_EINT 0x01 +#define DA9055_M_TEMP_EINT 0x02 +#define DA9055_M_COMP_1V2_EINT 0x04 +#define DA9055_M_LDO_LIM_EINT 0x08 +#define DA9055_M_NJIG_EINT 0x20 +#define DA9055_M_VDD_MON_EINT 0x40 +#define DA9055_M_VDD_WARN_EINT 0x80 + +/* DA9055_REG_IRQ_MASK_C (addr=0x09) */ +#define DA9055_M_GPI0_EINT 0x01 +#define DA9055_M_GPI1_EINT 0x02 +#define DA9055_M_GPI2_EINT 0x04 + +/* DA9055_REG_CONTROL_A (addr=0xA) */ +#define DA9055_DEBOUNCING_SHIFT 0x00 +#define DA9055_DEBOUNCING_MASK 0x07 +#define DA9055_NRES_MODE_SHIFT 0x03 +#define DA9055_NRES_MODE_MASK 0x08 +#define DA9055_SLEW_RATE_SHIFT 0x04 +#define DA9055_SLEW_RATE_MASK 0x30 +#define DA9055_NOKEY_LOCK_SHIFT 0x06 +#define DA9055_NOKEY_LOCK_MASK 0x40 + +/* DA9055_REG_CONTROL_B (addr=0xB) */ +#define DA9055_RTC_MODE_PD 0x01 +#define DA9055_RTC_MODE_SD_SHIFT 0x01 +#define DA9055_RTC_MODE_SD 0x02 +#define DA9055_RTC_EN 0x04 +#define DA9055_ECO_MODE_SHIFT 0x03 +#define DA9055_ECO_MODE_MASK 0x08 +#define DA9055_TWDSCALE_SHIFT 4 +#define DA9055_TWDSCALE_MASK 0x70 +#define DA9055_V_LOCK_SHIFT 0x07 +#define DA9055_V_LOCK_MASK 0x80 + +/* DA9055_REG_CONTROL_C (addr=0xC) */ +#define DA9055_SYSTEM_EN_SHIFT 0x00 +#define DA9055_SYSTEM_EN_MASK 0x01 +#define DA9055_POWERN_EN_SHIFT 0x01 +#define DA9055_POWERN_EN_MASK 0x02 +#define DA9055_POWER1_EN_SHIFT 0x02 +#define DA9055_POWER1_EN_MASK 0x04 + +/* DA9055_REG_CONTROL_D (addr=0xD) */ +#define DA9055_STANDBY_SHIFT 0x02 +#define DA9055_STANDBY_MASK 0x08 +#define DA9055_AUTO_BOOT_SHIFT 0x03 +#define DA9055_AUTO_BOOT_MASK 0x04 + +/* DA9055_REG_CONTROL_E (addr=0xE) */ +#define DA9055_WATCHDOG_SHIFT 0x00 +#define DA9055_WATCHDOG_MASK 0x01 +#define DA9055_SHUTDOWN_SHIFT 0x01 +#define DA9055_SHUTDOWN_MASK 0x02 +#define DA9055_WAKE_UP_SHIFT 0x02 +#define DA9055_WAKE_UP_MASK 0x04 + +/* DA9055_REG_GPIO (addr=0x10/0x11) */ +#define DA9055_GPIO0_PIN_SHIFT 0x00 +#define DA9055_GPIO0_PIN_MASK 0x03 +#define DA9055_GPIO0_TYPE_SHIFT 0x02 +#define DA9055_GPIO0_TYPE_MASK 0x04 +#define DA9055_GPIO0_WEN_SHIFT 0x03 +#define DA9055_GPIO0_WEN_MASK 0x08 +#define DA9055_GPIO1_PIN_SHIFT 0x04 +#define DA9055_GPIO1_PIN_MASK 0x30 +#define DA9055_GPIO1_TYPE_SHIFT 0x06 +#define DA9055_GPIO1_TYPE_MASK 0x40 +#define DA9055_GPIO1_WEN_SHIFT 0x07 +#define DA9055_GPIO1_WEN_MASK 0x80 +#define DA9055_GPIO2_PIN_SHIFT 0x00 +#define DA9055_GPIO2_PIN_MASK 0x30 +#define DA9055_GPIO2_TYPE_SHIFT 0x02 +#define DA9055_GPIO2_TYPE_MASK 0x04 +#define DA9055_GPIO2_WEN_SHIFT 0x03 +#define DA9055_GPIO2_WEN_MASK 0x08 + +/* DA9055_REG_GPIO_MODE (addr=0x12) */ +#define DA9055_GPIO0_MODE_SHIFT 0x00 +#define DA9055_GPIO0_MODE_MASK 0x01 +#define DA9055_GPIO1_MODE_SHIFT 0x01 +#define DA9055_GPIO1_MODE_MASK 0x02 +#define DA9055_GPIO2_MODE_SHIFT 0x02 +#define DA9055_GPIO2_MODE_MASK 0x04 + +/* DA9055_REG_BCORE_CONT (addr=0x13) */ +#define DA9055_BCORE_EN_SHIFT 0x00 +#define DA9055_BCORE_EN_MASK 0x01 +#define DA9055_BCORE_GPI_SHIFT 0x01 +#define DA9055_BCORE_GPI_MASK 0x02 +#define DA9055_BCORE_PD_DIS_SHIFT 0x03 +#define DA9055_BCORE_PD_DIS_MASK 0x04 +#define DA9055_VBCORE_SEL_SHIFT 0x04 +#define DA9055_SEL_REG_A 0x0 +#define DA9055_SEL_REG_B 0x10 +#define DA9055_VBCORE_SEL_MASK 0x10 +#define DA9055_V_GPI_MASK 0x60 +#define DA9055_V_GPI_SHIFT 0x05 +#define DA9055_E_GPI_MASK 0x06 +#define DA9055_E_GPI_SHIFT 0x01 +#define DA9055_VBCORE_GPI_SHIFT 0x05 +#define DA9055_VBCORE_GPI_MASK 0x60 +#define DA9055_BCORE_CONF_SHIFT 0x07 +#define DA9055_BCORE_CONF_MASK 0x80 + +/* DA9055_REG_BMEM_CONT (addr=0x14) */ +#define DA9055_BMEM_EN_SHIFT 0x00 +#define DA9055_BMEM_EN_MASK 0x01 +#define DA9055_BMEM_GPI_SHIFT 0x01 +#define DA9055_BMEM_GPI_MASK 0x06 +#define DA9055_BMEM_PD_DIS_SHIFT 0x03 +#define DA9055_BMEM_PD_DIS_MASK 0x08 +#define DA9055_VBMEM_SEL_SHIT 0x04 +#define DA9055_VBMEM_SEL_VBMEM_A (0<<4) +#define DA9055_VBMEM_SEL_VBMEM_B (1<<4) +#define DA9055_VBMEM_SEL_MASK 0x10 +#define DA9055_VBMEM_GPI_SHIFT 0x05 +#define DA9055_VBMEM_GPI_MASK 0x60 +#define DA9055_BMEM_CONF_SHIFT 0x07 +#define DA9055_BMEM_CONF_MASK 0x80 + +/* DA9055_REG_LDO_CONT (addr=0x15-0x1A) */ +#define DA9055_LDO_EN_SHIFT 0x00 +#define DA9055_LDO_EN_MASK 0x01 +#define DA9055_LDO_GPI_SHIFT 0x01 +#define DA9055_LDO_GPI_MASK 0x06 +#define DA9055_LDO_PD_DIS_SHIFT 0x03 +#define DA9055_LDO_PD_DIS_MASK 0x08 +#define DA9055_VLDO_SEL_SHIFT 0x04 +#define DA9055_VLDO_SEL_MASK 0x10 +#define DA9055_VLDO_SEL_VLDO_A 0x00 +#define DA9055_VLDO_SEL_VLDO_B 0x01 +#define DA9055_VLDO_GPI_SHIFT 0x05 +#define DA9055_VLDO_GPI_MASK 0x60 +#define DA9055_LDO_CONF_SHIFT 0x07 +#define DA9055_LDO_CONF_MASK 0x80 +#define DA9055_REGUALTOR_SET_A 0x00 +#define DA9055_REGUALTOR_SET_B 0x10 + +/* DA9055_REG_ADC_MAN (addr=0x1B) */ +#define DA9055_ADC_MUX_SHIFT 0 +#define DA9055_ADC_MUX_MASK 0xF +#define DA9055_ADC_MUX_VSYS 0x0 +#define DA9055_ADC_MUX_ADCIN1 0x01 +#define DA9055_ADC_MUX_ADCIN2 0x02 +#define DA9055_ADC_MUX_ADCIN3 0x03 +#define DA9055_ADC_MUX_T_SENSE 0x04 +#define DA9055_ADC_MAN_SHIFT 0x04 +#define DA9055_ADC_MAN_CONV 0x10 +#define DA9055_ADC_LSB_MASK 0X03 +#define DA9055_ADC_MODE_MASK 0x20 +#define DA9055_ADC_MODE_SHIFT 5 +#define DA9055_ADC_MODE_1MS (1<<5) +#define DA9055_COMP1V2_EN_SHIFT 7 + +/* DA9055_REG_ADC_CONT (addr=0x1C) */ +#define DA9055_ADC_AUTO_VSYS_EN_SHIFT 0 +#define DA9055_ADC_AUTO_AD1_EN_SHIFT 1 +#define DA9055_ADC_AUTO_AD2_EN_SHIFT 2 +#define DA9055_ADC_AUTO_AD3_EN_SHIFT 3 +#define DA9055_ADC_ISRC_EN_SHIFT 4 +#define DA9055_ADC_ADCIN1_DEB_SHIFT 5 +#define DA9055_ADC_ADCIN2_DEB_SHIFT 6 +#define DA9055_ADC_ADCIN3_DEB_SHIFT 7 +#define DA9055_AD1_ISRC_MASK 0x10 +#define DA9055_AD1_ISRC_SHIFT 4 + +/* DA9055_REG_VSYS_MON (addr=0x1D) */ +#define DA9055_VSYS_VAL_SHIFT 0 +#define DA9055_VSYS_VAL_MASK 0xFF +#define DA9055_VSYS_VAL_BASE 0x00 +#define DA9055_VSYS_VAL_MAX DA9055_VSYS_VAL_MASK +#define DA9055_VSYS_VOLT_BASE 2500 +#define DA9055_VSYS_VOLT_INC 10 +#define DA9055_VSYS_STEPS 255 +#define DA9055_VSYS_VOLT_MIN 2500 + +/* DA9044_REG_XXX_RES (addr=0x20-0x23) */ +#define DA9055_ADC_VAL_SHIFT 0 +#define DA9055_ADC_VAL_MASK 0xFF +#define DA9055_ADC_VAL_BASE 0x00 +#define DA9055_ADC_VAL_MAX DA9055_ADC_VAL_MASK +#define DA9055_ADC_VOLT_BASE 0 +#define DA9055_ADC_VSYS_VOLT_BASE 2500 +#define DA9055_ADC_VOLT_INC 10 +#define DA9055_ADC_VSYS_VOLT_INC 12 +#define DA9055_ADC_STEPS 255 + +/* DA9055_REG_EN_32K (addr=0x35)*/ +#define DA9055_STARTUP_TIME_MASK 0x07 +#define DA9055_STARTUP_TIME_0S 0x0 +#define DA9055_STARTUP_TIME_0_52S 0x1 +#define DA9055_STARTUP_TIME_1S 0x2 +#define DA9055_CRYSTAL_EN 0x08 +#define DA9055_DELAY_MODE_EN 0x10 +#define DA9055_OUT_CLCK_GATED 0x20 +#define DA9055_RTC_CLOCK_GATED 0x40 +#define DA9055_EN_32KOUT_BUF 0x80 + +/* DA9055_REG_RESET (addr=0x36) */ +/* Timer up to 31.744 ms */ +#define DA9055_RESET_TIMER_VAL_SHIFT 0 +#define DA9055_RESET_LOW_VAL_MASK 0x3F +#define DA9055_RESET_LOW_VAL_BASE 0 +#define DA9055_RESET_LOW_VAL_MAX DA9055_RESET_LOW_VAL_MASK +#define DA9055_RESET_US_LOW_BASE 1024 /* min val in units of us */ +#define DA9055_RESET_US_LOW_INC 1024 /* inc val in units of us */ +#define DA9055_RESET_US_LOW_STEP 30 + +/* Timer up to 1048.576ms */ +#define DA9055_RESET_HIGH_VAL_MASK 0x3F +#define DA9055_RESET_HIGH_VAL_BASE 0 +#define DA9055_RESET_HIGH_VAL_MAX DA9055_RESET_HIGH_VAL_MASK +#define DA9055_RESET_US_HIGH_BASE 32768 /* min val in units of us */ +#define DA9055_RESET_US_HIGH_INC 32768 /* inv val in units of us */ +#define DA9055_RESET_US_HIGH_STEP 31 + +/* DA9055_REG_BUCK_ILIM (addr=0x37)*/ +#define DA9055_BMEM_ILIM_SHIFT 0 +#define DA9055_ILIM_MASK 0x3 +#define DA9055_ILIM_500MA 0x0 +#define DA9055_ILIM_600MA 0x1 +#define DA9055_ILIM_700MA 0x2 +#define DA9055_ILIM_800MA 0x3 +#define DA9055_BCORE_ILIM_SHIFT 2 + +/* DA9055_REG_BCORE_MODE (addr=0x38) */ +#define DA9055_BMEM_MODE_SHIFT 0 +#define DA9055_MODE_MASK 0x3 +#define DA9055_MODE_AB 0x0 +#define DA9055_MODE_SLEEP 0x1 +#define DA9055_MODE_SYNCHRO 0x2 +#define DA9055_MODE_AUTO 0x3 +#define DA9055_BCORE_MODE_SHIFT 2 + +/* DA9055_REG_VBCORE_A/B (addr=0x39/0x41)*/ +#define DA9055_VBCORE_VAL_SHIFT 0 +#define DA9055_VBCORE_VAL_MASK 0x3F +#define DA9055_VBCORE_VAL_BASE 0x09 +#define DA9055_VBCORE_VAL_MAX DA9055_VBCORE_VAL_MASK +#define DA9055_VBCORE_VOLT_BASE 750 +#define DA9055_VBCORE_VOLT_INC 25 +#define DA9055_VBCORE_STEPS 53 +#define DA9055_VBCORE_VOLT_MIN DA9055_VBCORE_VOLT_BASE +#define DA9055_BCORE_SL_SYNCHRO (0<<7) +#define DA9055_BCORE_SL_SLEEP (1<<7) + +/* DA9055_REG_VBMEM_A/B (addr=0x3A/0x42)*/ +#define DA9055_VBMEM_VAL_SHIFT 0 +#define DA9055_VBMEM_VAL_MASK 0x3F +#define DA9055_VBMEM_VAL_BASE 0x00 +#define DA9055_VBMEM_VAL_MAX DA9055_VBMEM_VAL_MASK +#define DA9055_VBMEM_VOLT_BASE 925 +#define DA9055_VBMEM_VOLT_INC 25 +#define DA9055_VBMEM_STEPS 63 +#define DA9055_VBMEM_VOLT_MIN DA9055_VBMEM_VOLT_BASE +#define DA9055_BCMEM_SL_SYNCHRO (0<<7) +#define DA9055_BCMEM_SL_SLEEP (1<<7) + + +/* DA9055_REG_VLDO (addr=0x3B-0x40/0x43-0x48)*/ +#define DA9055_VLDO_VAL_SHIFT 0 +#define DA9055_VLDO_VAL_MASK 0x3F +#define DA9055_VLDO6_VAL_MASK 0x7F +#define DA9055_VLDO_VAL_BASE 0x02 +#define DA9055_VLDO2_VAL_BASE 0x03 +#define DA9055_VLDO6_VAL_BASE 0x00 +#define DA9055_VLDO_VAL_MAX DA9055_VLDO_VAL_MASK +#define DA9055_VLDO6_VAL_MAX DA9055_VLDO6_VAL_MASK +#define DA9055_VLDO_VOLT_BASE 900 +#define DA9055_VLDO_VOLT_INC 50 +#define DA9055_VLDO6_VOLT_INC 20 +#define DA9055_VLDO_STEPS 48 +#define DA9055_VLDO5_STEPS 37 +#define DA9055_VLDO6_STEPS 120 +#define DA9055_VLDO_VOLT_MIN DA9055_VLDO_VOLT_BASE +#define DA9055_LDO_MODE_SHIFT 7 +#define DA9055_LDO_SL_NORMAL 0 +#define DA9055_LDO_SL_SLEEP 1 + +/* DA9055_REG_OTP_CONT (addr=0x50) */ +#define DA9055_OTP_TIM_NORMAL (0<<0) +#define DA9055_OTP_TIM_MARGINAL (1<<0) +#define DA9055_OTP_GP_RD_SHIFT 1 +#define DA9055_OTP_APPS_RD_SHIFT 2 +#define DA9055_PC_DONE_SHIFT 3 +#define DA9055_OTP_GP_LOCK_SHIFT 4 +#define DA9055_OTP_APPS_LOCK_SHIFT 5 +#define DA9055_OTP_CONF_LOCK_SHIFT 6 +#define DA9055_OTP_WRITE_DIS_SHIFT 7 + +/* DA9055_REG_COUNT_S (addr=0x53) */ +#define DA9055_RTC_SEC 0x3F +#define DA9055_RTC_MONITOR_EN 0x40 +#define DA9055_RTC_READ 0x80 + +/* DA9055_REG_COUNT_MI (addr=0x54) */ +#define DA9055_RTC_MIN 0x3F + +/* DA9055_REG_COUNT_H (addr=0x55) */ +#define DA9055_RTC_HOUR 0x1F + +/* DA9055_REG_COUNT_D (addr=0x56) */ +#define DA9055_RTC_DAY 0x1F + +/* DA9055_REG_COUNT_MO (addr=0x57) */ +#define DA9055_RTC_MONTH 0x0F + +/* DA9055_REG_COUNT_Y (addr=0x58) */ +#define DA9055_RTC_YEAR 0x3F +#define DA9055_RTC_YEAR_BASE 2000 + +/* DA9055_REG_ALARM_MI (addr=0x59) */ +#define DA9055_RTC_ALM_MIN 0x3F +#define DA9055_ALARM_STATUS_SHIFT 6 +#define DA9055_ALARM_STATUS_MASK 0x3 +#define DA9055_ALARM_STATUS_NO_ALARM 0x0 +#define DA9055_ALARM_STATUS_TICK 0x1 +#define DA9055_ALARM_STATUS_TIMER_ALARM 0x2 +#define DA9055_ALARM_STATUS_BOTH 0x3 + +/* DA9055_REG_ALARM_H (addr=0x5A) */ +#define DA9055_RTC_ALM_HOUR 0x1F + +/* DA9055_REG_ALARM_D (addr=0x5B) */ +#define DA9055_RTC_ALM_DAY 0x1F + +/* DA9055_REG_ALARM_MO (addr=0x5C) */ +#define DA9055_RTC_ALM_MONTH 0x0F +#define DA9055_RTC_TICK_WAKE_MASK 0x20 +#define DA9055_RTC_TICK_WAKE_SHIFT 5 +#define DA9055_RTC_TICK_TYPE 0x10 +#define DA9055_RTC_TICK_TYPE_SHIFT 0x4 +#define DA9055_RTC_TICK_SEC 0x0 +#define DA9055_RTC_TICK_MIN 0x1 +#define DA9055_ALARAM_TICK_WAKE 0x20 + +/* DA9055_REG_ALARM_Y (addr=0x5D) */ +#define DA9055_RTC_TICK_EN 0x80 +#define DA9055_RTC_ALM_EN 0x40 +#define DA9055_RTC_TICK_ALM_MASK 0xC0 +#define DA9055_RTC_ALM_YEAR 0x3F + +/* DA9055_REG_TRIM_CLDR (addr=0x62) */ +#define DA9055_TRIM_32K_SHIFT 0 +#define DA9055_TRIM_32K_MASK 0x7F +#define DA9055_TRIM_DECREMENT (1<<7) +#define DA9055_TRIM_INCREMENT (0<<7) +#define DA9055_TRIM_VAL_BASE 0x0 +#define DA9055_TRIM_PPM_BASE 0x0 /* min val in units of 0.1PPM */ +#define DA9055_TRIM_PPM_INC 19 /* min inc in units of 0.1PPM */ +#define DA9055_TRIM_STEPS 127 + +/* DA9055_REG_CONFIG_A (addr=0x65) */ +#define DA9055_PM_I_V_VDDCORE (0<<0) +#define DA9055_PM_I_V_VDD_IO (1<<0) +#define DA9055_VDD_FAULT_TYPE_ACT_LOW (0<<1) +#define DA9055_VDD_FAULT_TYPE_ACT_HIGH (1<<1) +#define DA9055_PM_O_TYPE_PUSH_PULL (0<<2) +#define DA9055_PM_O_TYPE_OPEN_DRAIN (1<<2) +#define DA9055_IRQ_TYPE_ACT_LOW (0<<3) +#define DA9055_IRQ_TYPE_ACT_HIGH (1<<3) +#define DA9055_NIRQ_MODE_IMM (0<<4) +#define DA9055_NIRQ_MODE_ACTIVE (1<<4) +#define DA9055_GPI_V_VDDCORE (0<<5) +#define DA9055_GPI_V_VDD_IO (1<<5) +#define DA9055_PM_IF_V_VDDCORE (0<<6) +#define DA9055_PM_IF_V_VDD_IO (1<<6) + +/* DA9055_REG_CONFIG_B (addr=0x66) */ +#define DA9055_VDD_FAULT_VAL_SHIFT 0 +#define DA9055_VDD_FAULT_VAL_MASK 0xF +#define DA9055_VDD_FAULT_VAL_BASE 0x0 +#define DA9055_VDD_FAULT_VAL_MAX DA9055_VDD_FAULT_VAL_MASK +#define DA9055_VDD_FAULT_VOLT_BASE 2500 +#define DA9055_VDD_FAULT_VOLT_INC 50 +#define DA9055_VDD_FAULT_STEPS 15 + +#define DA9055_VDD_HYST_VAL_SHIFT 4 +#define DA9055_VDD_HYST_VAL_MASK 0x7 +#define DA9055_VDD_HYST_VAL_BASE 0x0 +#define DA9055_VDD_HYST_VAL_MAX DA9055_VDD_HYST_VAL_MASK +#define DA9055_VDD_HYST_VOLT_BASE 100 +#define DA9055_VDD_HYST_VOLT_INC 50 +#define DA9055_VDD_HYST_STEPS 7 +#define DA9055_VDD_HYST_VOLT_MIN DA9055_VDD_HYST_VOLT_BASE + +#define DA9055_VDD_FAULT_EN_SHIFT 7 + +/* DA9055_REG_CONFIG_C (addr=0x67) */ +#define DA9055_BCORE_CLK_INV_SHIFT 0 +#define DA9055_BMEM_CLK_INV_SHIFT 1 +#define DA9055_NFAULT_CONF_SHIFT 2 +#define DA9055_LDO_SD_SHIFT 4 +#define DA9055_LDO5_BYP_SHIFT 6 +#define DA9055_LDO6_BYP_SHIFT 7 + +/* DA9055_REG_CONFIG_D (addr=0x68) */ +#define DA9055_NONKEY_PIN_SHIFT 0 +#define DA9055_NONKEY_PIN_MASK 0x3 +#define DA9055_NONKEY_PIN_PORT_MODE 0x0 +#define DA9055_NONKEY_PIN_KEY_MODE 0x1 +#define DA9055_NONKEY_PIN_MULTI_FUNC 0x2 +#define DA9055_NONKEY_PIN_DEDICT 0x3 +#define DA9055_NONKEY_SD_SHIFT 2 +#define DA9055_KEY_DELAY_SHIFT 3 +#define DA9055_KEY_DELAY_MASK 0x3 +#define DA9055_KEY_DELAY_4S 0x0 +#define DA9055_KEY_DELAY_6S 0x1 +#define DA9055_KEY_DELAY_8S 0x2 +#define DA9055_KEY_DELAY_10S 0x3 + +/* DA9055_REG_CONFIG_E (addr=0x69) */ +#define DA9055_GPIO_PUPD_PULL_UP 0x0 +#define DA9055_GPIO_PUPD_OPEN_DRAIN 0x1 +#define DA9055_GPIO0_PUPD_SHIFT 0 +#define DA9055_GPIO1_PUPD_SHIFT 1 +#define DA9055_GPIO2_PUPD_SHIFT 2 +#define DA9055_UVOV_DELAY_SHIFT 4 +#define DA9055_UVOV_DELAY_MASK 0x3 +#define DA9055_RESET_DURATION_SHIFT 6 +#define DA9055_RESET_DURATION_MASK 0x3 +#define DA9055_RESET_DURATION_0MS 0x0 +#define DA9055_RESET_DURATION_100MS 0x1 +#define DA9055_RESET_DURATION_500MS 0x2 +#define DA9055_RESET_DURATION_1000MS 0x3 + +/* DA9055_REG_MON_REG_1 (addr=0x6A) */ +#define DA9055_MON_THRES_SHIFT 0 +#define DA9055_MON_THRES_MASK 0x3 +#define DA9055_MON_RES_SHIFT 2 +#define DA9055_MON_DEB_SHIFT 3 +#define DA9055_MON_MODE_SHIFT 4 +#define DA9055_MON_MODE_MASK 0x3 +#define DA9055_START_MAX_SHIFT 6 +#define DA9055_START_MAX_MASK 0x3 + +/* DA9055_REG_MON_REG_2 (addr=0x6B) */ +#define DA9055_LDO1_MON_EN_SHIFT 0 +#define DA9055_LDO2_MON_EN_SHIFT 1 +#define DA9055_LDO3_MON_EN_SHIFT 2 +#define DA9055_LDO4_MON_EN_SHIFT 3 +#define DA9055_LDO5_MON_EN_SHIFT 4 +#define DA9055_LDO6_MON_EN_SHIFT 5 +#define DA9055_BCORE_MON_EN_SHIFT 6 +#define DA9055_BMEM_MON_EN_SHIFT 7 + +/* DA9055_REG_CONFIG_F (addr=0x6C) */ +#define DA9055_LDO1_DEF_SHIFT 0 +#define DA9055_LDO2_DEF_SHIFT 1 +#define DA9055_LDO3_DEF_SHIFT 2 +#define DA9055_LDO4_DEF_SHIFT 3 +#define DA9055_LDO5_DEF_SHIFT 4 +#define DA9055_LDO6_DEF_SHIFT 5 +#define DA9055_BCORE_DEF_SHIFT 6 +#define DA9055_BMEM_DEF_SHIFT 7 + +/* DA9055_REG_MON_REG_4 (addr=0x6D) */ +#define DA9055_MON_A8_IDX_SHIFT 0 +#define DA9055_MON_A89_IDX_MASK 0x3 +#define DA9055_MON_A89_IDX_NONE 0x0 +#define DA9055_MON_A89_IDX_BUCKCORE 0x1 +#define DA9055_MON_A89_IDX_LDO3 0x2 +#define DA9055_MON_A9_IDX_SHIFT 5 + +/* DA9055_REG_MON_REG_5 (addr=0x6E) */ +#define DA9055_MON_A10_IDX_SHIFT 0 +#define DA9055_MON_A10_IDX_MASK 0x3 +#define DA9055_MON_A10_IDX_NONE 0x0 +#define DA9055_MON_A10_IDX_LDO1 0x1 +#define DA9055_MON_A10_IDX_LDO2 0x2 +#define DA9055_MON_A10_IDX_LDO5 0x3 +#define DA9055_MON_A10_IDX_LDO6 0x4 + +#endif /* __DA9055_REG_H */ diff --git a/include/linux/mfd/lp8788-isink.h b/include/linux/mfd/lp8788-isink.h new file mode 100644 index 000000000000..f38262d21ff1 --- /dev/null +++ b/include/linux/mfd/lp8788-isink.h @@ -0,0 +1,52 @@ +/* + * TI LP8788 MFD - common definitions for current sinks + * + * Copyright 2012 Texas Instruments + * + * Author: Milo(Woogyom) Kim <milo.kim@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef __ISINK_LP8788_H__ +#define __ISINK_LP8788_H__ + +/* register address */ +#define LP8788_ISINK_CTRL 0x99 +#define LP8788_ISINK12_IOUT 0x9A +#define LP8788_ISINK3_IOUT 0x9B +#define LP8788_ISINK1_PWM 0x9C +#define LP8788_ISINK2_PWM 0x9D +#define LP8788_ISINK3_PWM 0x9E + +/* mask bits */ +#define LP8788_ISINK1_IOUT_M 0x0F /* Addr 9Ah */ +#define LP8788_ISINK2_IOUT_M 0xF0 +#define LP8788_ISINK3_IOUT_M 0x0F /* Addr 9Bh */ + +/* 6 bits used for PWM code : Addr 9C ~ 9Eh */ +#define LP8788_ISINK_MAX_PWM 63 +#define LP8788_ISINK_SCALE_OFFSET 3 + +static const u8 lp8788_iout_addr[] = { + LP8788_ISINK12_IOUT, + LP8788_ISINK12_IOUT, + LP8788_ISINK3_IOUT, +}; + +static const u8 lp8788_iout_mask[] = { + LP8788_ISINK1_IOUT_M, + LP8788_ISINK2_IOUT_M, + LP8788_ISINK3_IOUT_M, +}; + +static const u8 lp8788_pwm_addr[] = { + LP8788_ISINK1_PWM, + LP8788_ISINK2_PWM, + LP8788_ISINK3_PWM, +}; + +#endif diff --git a/include/linux/mfd/lp8788.h b/include/linux/mfd/lp8788.h new file mode 100644 index 000000000000..cec364bdccfa --- /dev/null +++ b/include/linux/mfd/lp8788.h @@ -0,0 +1,364 @@ +/* + * TI LP8788 MFD Device + * + * Copyright 2012 Texas Instruments + * + * Author: Milo(Woogyom) Kim <milo.kim@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef __MFD_LP8788_H__ +#define __MFD_LP8788_H__ + +#include <linux/gpio.h> +#include <linux/irqdomain.h> +#include <linux/regmap.h> + +#define LP8788_DEV_BUCK "lp8788-buck" +#define LP8788_DEV_DLDO "lp8788-dldo" +#define LP8788_DEV_ALDO "lp8788-aldo" +#define LP8788_DEV_CHARGER "lp8788-charger" +#define LP8788_DEV_RTC "lp8788-rtc" +#define LP8788_DEV_BACKLIGHT "lp8788-backlight" +#define LP8788_DEV_VIBRATOR "lp8788-vibrator" +#define LP8788_DEV_KEYLED "lp8788-keyled" +#define LP8788_DEV_ADC "lp8788-adc" + +#define LP8788_NUM_BUCKS 4 +#define LP8788_NUM_DLDOS 12 +#define LP8788_NUM_ALDOS 10 +#define LP8788_NUM_BUCK2_DVS 2 + +#define LP8788_CHG_IRQ "CHG_IRQ" +#define LP8788_PRSW_IRQ "PRSW_IRQ" +#define LP8788_BATT_IRQ "BATT_IRQ" +#define LP8788_ALM_IRQ "ALARM_IRQ" + +enum lp8788_int_id { + /* interrup register 1 : Addr 00h */ + LP8788_INT_TSDL, + LP8788_INT_TSDH, + LP8788_INT_UVLO, + LP8788_INT_FLAGMON, + LP8788_INT_PWRON_TIME, + LP8788_INT_PWRON, + LP8788_INT_COMP1, + LP8788_INT_COMP2, + + /* interrupt register 2 : Addr 01h */ + LP8788_INT_CHG_INPUT_STATE, + LP8788_INT_CHG_STATE, + LP8788_INT_EOC, + LP8788_INT_CHG_RESTART, + LP8788_INT_RESTART_TIMEOUT, + LP8788_INT_FULLCHG_TIMEOUT, + LP8788_INT_PRECHG_TIMEOUT, + + /* interrupt register 3 : Addr 02h */ + LP8788_INT_RTC_ALARM1 = 17, + LP8788_INT_RTC_ALARM2, + LP8788_INT_ENTER_SYS_SUPPORT, + LP8788_INT_EXIT_SYS_SUPPORT, + LP8788_INT_BATT_LOW, + LP8788_INT_NO_BATT, + + LP8788_INT_MAX = 24, +}; + +enum lp8788_dvs_sel { + DVS_SEL_V0, + DVS_SEL_V1, + DVS_SEL_V2, + DVS_SEL_V3, +}; + +enum lp8788_ext_ldo_en_id { + EN_ALDO1, + EN_ALDO234, + EN_ALDO5, + EN_ALDO7, + EN_DLDO7, + EN_DLDO911, + EN_LDOS_MAX, +}; + +enum lp8788_charger_event { + NO_CHARGER, + CHARGER_DETECTED, +}; + +enum lp8788_bl_ctrl_mode { + LP8788_BL_REGISTER_ONLY, + LP8788_BL_COMB_PWM_BASED, /* PWM + I2C, changed by PWM input */ + LP8788_BL_COMB_REGISTER_BASED, /* PWM + I2C, changed by I2C */ +}; + +enum lp8788_bl_dim_mode { + LP8788_DIM_EXPONENTIAL, + LP8788_DIM_LINEAR, +}; + +enum lp8788_bl_full_scale_current { + LP8788_FULLSCALE_5000uA, + LP8788_FULLSCALE_8500uA, + LP8788_FULLSCALE_1200uA, + LP8788_FULLSCALE_1550uA, + LP8788_FULLSCALE_1900uA, + LP8788_FULLSCALE_2250uA, + LP8788_FULLSCALE_2600uA, + LP8788_FULLSCALE_2950uA, +}; + +enum lp8788_bl_ramp_step { + LP8788_RAMP_8us, + LP8788_RAMP_1024us, + LP8788_RAMP_2048us, + LP8788_RAMP_4096us, + LP8788_RAMP_8192us, + LP8788_RAMP_16384us, + LP8788_RAMP_32768us, + LP8788_RAMP_65538us, +}; + +enum lp8788_bl_pwm_polarity { + LP8788_PWM_ACTIVE_HIGH, + LP8788_PWM_ACTIVE_LOW, +}; + +enum lp8788_isink_scale { + LP8788_ISINK_SCALE_100mA, + LP8788_ISINK_SCALE_120mA, +}; + +enum lp8788_isink_number { + LP8788_ISINK_1, + LP8788_ISINK_2, + LP8788_ISINK_3, +}; + +enum lp8788_alarm_sel { + LP8788_ALARM_1, + LP8788_ALARM_2, + LP8788_ALARM_MAX, +}; + +enum lp8788_adc_id { + LPADC_VBATT_5P5, + LPADC_VIN_CHG, + LPADC_IBATT, + LPADC_IC_TEMP, + LPADC_VBATT_6P0, + LPADC_VBATT_5P0, + LPADC_ADC1, + LPADC_ADC2, + LPADC_VDD, + LPADC_VCOIN, + LPADC_VDD_LDO, + LPADC_ADC3, + LPADC_ADC4, + LPADC_MAX, +}; + +struct lp8788; + +/* + * lp8788_buck1_dvs + * @gpio : gpio pin number for dvs control + * @vsel : dvs selector for buck v1 register + */ +struct lp8788_buck1_dvs { + int gpio; + enum lp8788_dvs_sel vsel; +}; + +/* + * lp8788_buck2_dvs + * @gpio : two gpio pin numbers are used for dvs + * @vsel : dvs selector for buck v2 register + */ +struct lp8788_buck2_dvs { + int gpio[LP8788_NUM_BUCK2_DVS]; + enum lp8788_dvs_sel vsel; +}; + +/* + * struct lp8788_ldo_enable_pin + * + * Basically, all LDOs are enabled through the I2C commands. + * But ALDO 1 ~ 5, 7, DLDO 7, 9, 11 can be enabled by external gpio pins. + * + * @gpio : gpio number which is used for enabling ldos + * @init_state : initial gpio state (ex. GPIOF_OUT_INIT_LOW) + */ +struct lp8788_ldo_enable_pin { + int gpio; + int init_state; +}; + +/* + * struct lp8788_chg_param + * @addr : charging control register address (range : 0x11 ~ 0x1C) + * @val : charging parameter value + */ +struct lp8788_chg_param { + u8 addr; + u8 val; +}; + +/* + * struct lp8788_charger_platform_data + * @vbatt_adc : adc selection id for battery voltage + * @batt_temp_adc : adc selection id for battery temperature + * @max_vbatt_mv : used for calculating battery capacity + * @chg_params : initial charging parameters + * @num_chg_params : numbers of charging parameters + * @charger_event : the charger event can be reported to the platform side + */ +struct lp8788_charger_platform_data { + enum lp8788_adc_id vbatt_adc; + enum lp8788_adc_id batt_temp_adc; + unsigned int max_vbatt_mv; + struct lp8788_chg_param *chg_params; + int num_chg_params; + void (*charger_event) (struct lp8788 *lp, + enum lp8788_charger_event event); +}; + +/* + * struct lp8788_bl_pwm_data + * @pwm_set_intensity : set duty of pwm + * @pwm_get_intensity : get current duty of pwm + */ +struct lp8788_bl_pwm_data { + void (*pwm_set_intensity) (int brightness, int max_brightness); + int (*pwm_get_intensity) (int max_brightness); +}; + +/* + * struct lp8788_backlight_platform_data + * @name : backlight driver name. (default: "lcd-backlight") + * @initial_brightness : initial value of backlight brightness + * @bl_mode : brightness control by pwm or lp8788 register + * @dim_mode : dimming mode selection + * @full_scale : full scale current setting + * @rise_time : brightness ramp up step time + * @fall_time : brightness ramp down step time + * @pwm_pol : pwm polarity setting when bl_mode is pwm based + * @pwm_data : platform specific pwm generation functions + * only valid when bl_mode is pwm based + */ +struct lp8788_backlight_platform_data { + char *name; + int initial_brightness; + enum lp8788_bl_ctrl_mode bl_mode; + enum lp8788_bl_dim_mode dim_mode; + enum lp8788_bl_full_scale_current full_scale; + enum lp8788_bl_ramp_step rise_time; + enum lp8788_bl_ramp_step fall_time; + enum lp8788_bl_pwm_polarity pwm_pol; + struct lp8788_bl_pwm_data pwm_data; +}; + +/* + * struct lp8788_led_platform_data + * @name : led driver name. (default: "keyboard-backlight") + * @scale : current scale + * @num : current sink number + * @iout_code : current output value (Addr 9Ah ~ 9Bh) + */ +struct lp8788_led_platform_data { + char *name; + enum lp8788_isink_scale scale; + enum lp8788_isink_number num; + int iout_code; +}; + +/* + * struct lp8788_vib_platform_data + * @name : vibrator driver name + * @scale : current scale + * @num : current sink number + * @iout_code : current output value (Addr 9Ah ~ 9Bh) + * @pwm_code : PWM code value (Addr 9Ch ~ 9Eh) + */ +struct lp8788_vib_platform_data { + char *name; + enum lp8788_isink_scale scale; + enum lp8788_isink_number num; + int iout_code; + int pwm_code; +}; + +/* + * struct lp8788_platform_data + * @init_func : used for initializing registers + * before mfd driver is registered + * @buck_data : regulator initial data for buck + * @dldo_data : regulator initial data for digital ldo + * @aldo_data : regulator initial data for analog ldo + * @buck1_dvs : gpio configurations for buck1 dvs + * @buck2_dvs : gpio configurations for buck2 dvs + * @ldo_pin : gpio configurations for enabling LDOs + * @chg_pdata : platform data for charger driver + * @alarm_sel : rtc alarm selection (1 or 2) + * @bl_pdata : configurable data for backlight driver + * @led_pdata : configurable data for led driver + * @vib_pdata : configurable data for vibrator driver + * @adc_pdata : iio map data for adc driver + */ +struct lp8788_platform_data { + /* general system information */ + int (*init_func) (struct lp8788 *lp); + + /* regulators */ + struct regulator_init_data *buck_data[LP8788_NUM_BUCKS]; + struct regulator_init_data *dldo_data[LP8788_NUM_DLDOS]; + struct regulator_init_data *aldo_data[LP8788_NUM_ALDOS]; + struct lp8788_buck1_dvs *buck1_dvs; + struct lp8788_buck2_dvs *buck2_dvs; + struct lp8788_ldo_enable_pin *ldo_pin[EN_LDOS_MAX]; + + /* charger */ + struct lp8788_charger_platform_data *chg_pdata; + + /* rtc alarm */ + enum lp8788_alarm_sel alarm_sel; + + /* backlight */ + struct lp8788_backlight_platform_data *bl_pdata; + + /* current sinks */ + struct lp8788_led_platform_data *led_pdata; + struct lp8788_vib_platform_data *vib_pdata; + + /* adc iio map data */ + struct iio_map *adc_pdata; +}; + +/* + * struct lp8788 + * @dev : parent device pointer + * @regmap : used for i2c communcation on accessing registers + * @irqdm : interrupt domain for handling nested interrupt + * @irq : pin number of IRQ_N + * @pdata : lp8788 platform specific data + */ +struct lp8788 { + struct device *dev; + struct regmap *regmap; + struct irq_domain *irqdm; + int irq; + struct lp8788_platform_data *pdata; +}; + +int lp8788_irq_init(struct lp8788 *lp, int chip_irq); +void lp8788_irq_exit(struct lp8788 *lp); +int lp8788_read_byte(struct lp8788 *lp, u8 reg, u8 *data); +int lp8788_read_multi_bytes(struct lp8788 *lp, u8 reg, u8 *data, size_t count); +int lp8788_write_byte(struct lp8788 *lp, u8 reg, u8 data); +int lp8788_update_bits(struct lp8788 *lp, u8 reg, u8 mask, u8 data); +#endif diff --git a/include/linux/mfd/lpc_ich.h b/include/linux/mfd/lpc_ich.h index fec5256c3f5d..3e1df644c407 100644 --- a/include/linux/mfd/lpc_ich.h +++ b/include/linux/mfd/lpc_ich.h @@ -43,6 +43,7 @@ struct lpc_ich_info { char name[32]; unsigned int iTCO_version; unsigned int gpio_version; + u8 use_gpio; }; #endif diff --git a/include/linux/mfd/max8907.h b/include/linux/mfd/max8907.h new file mode 100644 index 000000000000..b06f7a6a1e80 --- /dev/null +++ b/include/linux/mfd/max8907.h @@ -0,0 +1,252 @@ +/* + * Functions to access MAX8907 power management chip. + * + * Copyright (C) 2010 Gyungoh Yoo <jack.yoo@maxim-ic.com> + * Copyright (C) 2012, NVIDIA CORPORATION. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __LINUX_MFD_MAX8907_H +#define __LINUX_MFD_MAX8907_H + +#include <linux/mutex.h> +#include <linux/pm.h> + +#define MAX8907_GEN_I2C_ADDR (0x78 >> 1) +#define MAX8907_ADC_I2C_ADDR (0x8e >> 1) +#define MAX8907_RTC_I2C_ADDR (0xd0 >> 1) + +/* MAX8907 register map */ +#define MAX8907_REG_SYSENSEL 0x00 +#define MAX8907_REG_ON_OFF_IRQ1 0x01 +#define MAX8907_REG_ON_OFF_IRQ1_MASK 0x02 +#define MAX8907_REG_ON_OFF_STAT 0x03 +#define MAX8907_REG_SDCTL1 0x04 +#define MAX8907_REG_SDSEQCNT1 0x05 +#define MAX8907_REG_SDV1 0x06 +#define MAX8907_REG_SDCTL2 0x07 +#define MAX8907_REG_SDSEQCNT2 0x08 +#define MAX8907_REG_SDV2 0x09 +#define MAX8907_REG_SDCTL3 0x0A +#define MAX8907_REG_SDSEQCNT3 0x0B +#define MAX8907_REG_SDV3 0x0C +#define MAX8907_REG_ON_OFF_IRQ2 0x0D +#define MAX8907_REG_ON_OFF_IRQ2_MASK 0x0E +#define MAX8907_REG_RESET_CNFG 0x0F +#define MAX8907_REG_LDOCTL16 0x10 +#define MAX8907_REG_LDOSEQCNT16 0x11 +#define MAX8907_REG_LDO16VOUT 0x12 +#define MAX8907_REG_SDBYSEQCNT 0x13 +#define MAX8907_REG_LDOCTL17 0x14 +#define MAX8907_REG_LDOSEQCNT17 0x15 +#define MAX8907_REG_LDO17VOUT 0x16 +#define MAX8907_REG_LDOCTL1 0x18 +#define MAX8907_REG_LDOSEQCNT1 0x19 +#define MAX8907_REG_LDO1VOUT 0x1A +#define MAX8907_REG_LDOCTL2 0x1C +#define MAX8907_REG_LDOSEQCNT2 0x1D +#define MAX8907_REG_LDO2VOUT 0x1E +#define MAX8907_REG_LDOCTL3 0x20 +#define MAX8907_REG_LDOSEQCNT3 0x21 +#define MAX8907_REG_LDO3VOUT 0x22 +#define MAX8907_REG_LDOCTL4 0x24 +#define MAX8907_REG_LDOSEQCNT4 0x25 +#define MAX8907_REG_LDO4VOUT 0x26 +#define MAX8907_REG_LDOCTL5 0x28 +#define MAX8907_REG_LDOSEQCNT5 0x29 +#define MAX8907_REG_LDO5VOUT 0x2A +#define MAX8907_REG_LDOCTL6 0x2C +#define MAX8907_REG_LDOSEQCNT6 0x2D +#define MAX8907_REG_LDO6VOUT 0x2E +#define MAX8907_REG_LDOCTL7 0x30 +#define MAX8907_REG_LDOSEQCNT7 0x31 +#define MAX8907_REG_LDO7VOUT 0x32 +#define MAX8907_REG_LDOCTL8 0x34 +#define MAX8907_REG_LDOSEQCNT8 0x35 +#define MAX8907_REG_LDO8VOUT 0x36 +#define MAX8907_REG_LDOCTL9 0x38 +#define MAX8907_REG_LDOSEQCNT9 0x39 +#define MAX8907_REG_LDO9VOUT 0x3A +#define MAX8907_REG_LDOCTL10 0x3C +#define MAX8907_REG_LDOSEQCNT10 0x3D +#define MAX8907_REG_LDO10VOUT 0x3E +#define MAX8907_REG_LDOCTL11 0x40 +#define MAX8907_REG_LDOSEQCNT11 0x41 +#define MAX8907_REG_LDO11VOUT 0x42 +#define MAX8907_REG_LDOCTL12 0x44 +#define MAX8907_REG_LDOSEQCNT12 0x45 +#define MAX8907_REG_LDO12VOUT 0x46 +#define MAX8907_REG_LDOCTL13 0x48 +#define MAX8907_REG_LDOSEQCNT13 0x49 +#define MAX8907_REG_LDO13VOUT 0x4A +#define MAX8907_REG_LDOCTL14 0x4C +#define MAX8907_REG_LDOSEQCNT14 0x4D +#define MAX8907_REG_LDO14VOUT 0x4E +#define MAX8907_REG_LDOCTL15 0x50 +#define MAX8907_REG_LDOSEQCNT15 0x51 +#define MAX8907_REG_LDO15VOUT 0x52 +#define MAX8907_REG_OUT5VEN 0x54 +#define MAX8907_REG_OUT5VSEQ 0x55 +#define MAX8907_REG_OUT33VEN 0x58 +#define MAX8907_REG_OUT33VSEQ 0x59 +#define MAX8907_REG_LDOCTL19 0x5C +#define MAX8907_REG_LDOSEQCNT19 0x5D +#define MAX8907_REG_LDO19VOUT 0x5E +#define MAX8907_REG_LBCNFG 0x60 +#define MAX8907_REG_SEQ1CNFG 0x64 +#define MAX8907_REG_SEQ2CNFG 0x65 +#define MAX8907_REG_SEQ3CNFG 0x66 +#define MAX8907_REG_SEQ4CNFG 0x67 +#define MAX8907_REG_SEQ5CNFG 0x68 +#define MAX8907_REG_SEQ6CNFG 0x69 +#define MAX8907_REG_SEQ7CNFG 0x6A +#define MAX8907_REG_LDOCTL18 0x72 +#define MAX8907_REG_LDOSEQCNT18 0x73 +#define MAX8907_REG_LDO18VOUT 0x74 +#define MAX8907_REG_BBAT_CNFG 0x78 +#define MAX8907_REG_CHG_CNTL1 0x7C +#define MAX8907_REG_CHG_CNTL2 0x7D +#define MAX8907_REG_CHG_IRQ1 0x7E +#define MAX8907_REG_CHG_IRQ2 0x7F +#define MAX8907_REG_CHG_IRQ1_MASK 0x80 +#define MAX8907_REG_CHG_IRQ2_MASK 0x81 +#define MAX8907_REG_CHG_STAT 0x82 +#define MAX8907_REG_WLED_MODE_CNTL 0x84 +#define MAX8907_REG_ILED_CNTL 0x84 +#define MAX8907_REG_II1RR 0x8E +#define MAX8907_REG_II2RR 0x8F +#define MAX8907_REG_LDOCTL20 0x9C +#define MAX8907_REG_LDOSEQCNT20 0x9D +#define MAX8907_REG_LDO20VOUT 0x9E + +/* RTC register map */ +#define MAX8907_REG_RTC_SEC 0x00 +#define MAX8907_REG_RTC_MIN 0x01 +#define MAX8907_REG_RTC_HOURS 0x02 +#define MAX8907_REG_RTC_WEEKDAY 0x03 +#define MAX8907_REG_RTC_DATE 0x04 +#define MAX8907_REG_RTC_MONTH 0x05 +#define MAX8907_REG_RTC_YEAR1 0x06 +#define MAX8907_REG_RTC_YEAR2 0x07 +#define MAX8907_REG_ALARM0_SEC 0x08 +#define MAX8907_REG_ALARM0_MIN 0x09 +#define MAX8907_REG_ALARM0_HOURS 0x0A +#define MAX8907_REG_ALARM0_WEEKDAY 0x0B +#define MAX8907_REG_ALARM0_DATE 0x0C +#define MAX8907_REG_ALARM0_MONTH 0x0D +#define MAX8907_REG_ALARM0_YEAR1 0x0E +#define MAX8907_REG_ALARM0_YEAR2 0x0F +#define MAX8907_REG_ALARM1_SEC 0x10 +#define MAX8907_REG_ALARM1_MIN 0x11 +#define MAX8907_REG_ALARM1_HOURS 0x12 +#define MAX8907_REG_ALARM1_WEEKDAY 0x13 +#define MAX8907_REG_ALARM1_DATE 0x14 +#define MAX8907_REG_ALARM1_MONTH 0x15 +#define MAX8907_REG_ALARM1_YEAR1 0x16 +#define MAX8907_REG_ALARM1_YEAR2 0x17 +#define MAX8907_REG_ALARM0_CNTL 0x18 +#define MAX8907_REG_ALARM1_CNTL 0x19 +#define MAX8907_REG_RTC_STATUS 0x1A +#define MAX8907_REG_RTC_CNTL 0x1B +#define MAX8907_REG_RTC_IRQ 0x1C +#define MAX8907_REG_RTC_IRQ_MASK 0x1D +#define MAX8907_REG_MPL_CNTL 0x1E + +/* ADC and Touch Screen Controller register map */ +#define MAX8907_CTL 0 +#define MAX8907_SEQCNT 1 +#define MAX8907_VOUT 2 + +/* mask bit fields */ +#define MAX8907_MASK_LDO_SEQ 0x1C +#define MAX8907_MASK_LDO_EN 0x01 +#define MAX8907_MASK_VBBATTCV 0x03 +#define MAX8907_MASK_OUT5V_VINEN 0x10 +#define MAX8907_MASK_OUT5V_ENSRC 0x0E +#define MAX8907_MASK_OUT5V_EN 0x01 +#define MAX8907_MASK_POWER_OFF 0x40 + +/* Regulator IDs */ +#define MAX8907_MBATT 0 +#define MAX8907_SD1 1 +#define MAX8907_SD2 2 +#define MAX8907_SD3 3 +#define MAX8907_LDO1 4 +#define MAX8907_LDO2 5 +#define MAX8907_LDO3 6 +#define MAX8907_LDO4 7 +#define MAX8907_LDO5 8 +#define MAX8907_LDO6 9 +#define MAX8907_LDO7 10 +#define MAX8907_LDO8 11 +#define MAX8907_LDO9 12 +#define MAX8907_LDO10 13 +#define MAX8907_LDO11 14 +#define MAX8907_LDO12 15 +#define MAX8907_LDO13 16 +#define MAX8907_LDO14 17 +#define MAX8907_LDO15 18 +#define MAX8907_LDO16 19 +#define MAX8907_LDO17 20 +#define MAX8907_LDO18 21 +#define MAX8907_LDO19 22 +#define MAX8907_LDO20 23 +#define MAX8907_OUT5V 24 +#define MAX8907_OUT33V 25 +#define MAX8907_BBAT 26 +#define MAX8907_SDBY 27 +#define MAX8907_VRTC 28 +#define MAX8907_NUM_REGULATORS (MAX8907_VRTC + 1) + +/* IRQ definitions */ +enum { + MAX8907_IRQ_VCHG_DC_OVP = 0, + MAX8907_IRQ_VCHG_DC_F, + MAX8907_IRQ_VCHG_DC_R, + MAX8907_IRQ_VCHG_THM_OK_R, + MAX8907_IRQ_VCHG_THM_OK_F, + MAX8907_IRQ_VCHG_MBATTLOW_F, + MAX8907_IRQ_VCHG_MBATTLOW_R, + MAX8907_IRQ_VCHG_RST, + MAX8907_IRQ_VCHG_DONE, + MAX8907_IRQ_VCHG_TOPOFF, + MAX8907_IRQ_VCHG_TMR_FAULT, + + MAX8907_IRQ_GPM_RSTIN = 0, + MAX8907_IRQ_GPM_MPL, + MAX8907_IRQ_GPM_SW_3SEC, + MAX8907_IRQ_GPM_EXTON_F, + MAX8907_IRQ_GPM_EXTON_R, + MAX8907_IRQ_GPM_SW_1SEC, + MAX8907_IRQ_GPM_SW_F, + MAX8907_IRQ_GPM_SW_R, + MAX8907_IRQ_GPM_SYSCKEN_F, + MAX8907_IRQ_GPM_SYSCKEN_R, + + MAX8907_IRQ_RTC_ALARM1 = 0, + MAX8907_IRQ_RTC_ALARM0, +}; + +struct max8907_platform_data { + struct regulator_init_data *init_data[MAX8907_NUM_REGULATORS]; + bool pm_off; +}; + +struct regmap_irq_chips_data; + +struct max8907 { + struct device *dev; + struct mutex irq_lock; + struct i2c_client *i2c_gen; + struct i2c_client *i2c_rtc; + struct regmap *regmap_gen; + struct regmap *regmap_rtc; + struct regmap_irq_chip_data *irqc_chg; + struct regmap_irq_chip_data *irqc_on_off; + struct regmap_irq_chip_data *irqc_rtc; +}; + +#endif diff --git a/include/linux/mfd/max8925.h b/include/linux/mfd/max8925.h index 15b2392a56fb..74d8e2969630 100644 --- a/include/linux/mfd/max8925.h +++ b/include/linux/mfd/max8925.h @@ -158,8 +158,6 @@ enum { #define TSC_IRQ_MASK (0x03) #define RTC_IRQ_MASK (0x0c) -#define MAX8925_MAX_REGULATOR (23) - #define MAX8925_NAME_SIZE (32) /* IRQ definitions */ @@ -236,7 +234,29 @@ struct max8925_platform_data { struct max8925_backlight_pdata *backlight; struct max8925_touch_pdata *touch; struct max8925_power_pdata *power; - struct regulator_init_data *regulator[MAX8925_MAX_REGULATOR]; + struct regulator_init_data *sd1; + struct regulator_init_data *sd2; + struct regulator_init_data *sd3; + struct regulator_init_data *ldo1; + struct regulator_init_data *ldo2; + struct regulator_init_data *ldo3; + struct regulator_init_data *ldo4; + struct regulator_init_data *ldo5; + struct regulator_init_data *ldo6; + struct regulator_init_data *ldo7; + struct regulator_init_data *ldo8; + struct regulator_init_data *ldo9; + struct regulator_init_data *ldo10; + struct regulator_init_data *ldo11; + struct regulator_init_data *ldo12; + struct regulator_init_data *ldo13; + struct regulator_init_data *ldo14; + struct regulator_init_data *ldo15; + struct regulator_init_data *ldo16; + struct regulator_init_data *ldo17; + struct regulator_init_data *ldo18; + struct regulator_init_data *ldo19; + struct regulator_init_data *ldo20; int irq_base; int tsc_irq; diff --git a/include/linux/mfd/palmas.h b/include/linux/mfd/palmas.h index 9cbc642d40ad..29f6616e12f0 100644 --- a/include/linux/mfd/palmas.h +++ b/include/linux/mfd/palmas.h @@ -23,6 +23,9 @@ #define PALMAS_NUM_CLIENTS 3 struct palmas_pmic; +struct palmas_gpadc; +struct palmas_resource; +struct palmas_usb; struct palmas { struct device *dev; @@ -41,6 +44,9 @@ struct palmas { /* Child Devices */ struct palmas_pmic *pmic; + struct palmas_gpadc *gpadc; + struct palmas_resource *resource; + struct palmas_usb *usb; /* GPIO MUXing */ u8 gpio_muxed; @@ -48,6 +54,23 @@ struct palmas { u8 pwm_muxed; }; +struct palmas_gpadc_platform_data { + /* Channel 3 current source is only enabled during conversion */ + int ch3_current; + + /* Channel 0 current source can be used for battery detection. + * If used for battery detection this will cause a permanent current + * consumption depending on current level set here. + */ + int ch0_current; + + /* default BAT_REMOVAL_DAT setting on device probe */ + int bat_removal; + + /* Sets the START_POLARITY bit in the RT_CTRL register */ + int start_polarity; +}; + struct palmas_reg_init { /* warm_rest controls the voltage levels after a warm reset * @@ -107,21 +130,94 @@ struct palmas_reg_init { }; +enum palmas_regulators { + /* SMPS regulators */ + PALMAS_REG_SMPS12, + PALMAS_REG_SMPS123, + PALMAS_REG_SMPS3, + PALMAS_REG_SMPS45, + PALMAS_REG_SMPS457, + PALMAS_REG_SMPS6, + PALMAS_REG_SMPS7, + PALMAS_REG_SMPS8, + PALMAS_REG_SMPS9, + PALMAS_REG_SMPS10, + /* LDO regulators */ + PALMAS_REG_LDO1, + PALMAS_REG_LDO2, + PALMAS_REG_LDO3, + PALMAS_REG_LDO4, + PALMAS_REG_LDO5, + PALMAS_REG_LDO6, + PALMAS_REG_LDO7, + PALMAS_REG_LDO8, + PALMAS_REG_LDO9, + PALMAS_REG_LDOLN, + PALMAS_REG_LDOUSB, + /* Total number of regulators */ + PALMAS_NUM_REGS, +}; + struct palmas_pmic_platform_data { /* An array of pointers to regulator init data indexed by regulator * ID */ - struct regulator_init_data **reg_data; + struct regulator_init_data *reg_data[PALMAS_NUM_REGS]; /* An array of pointers to structures containing sleep mode and DVS * configuration for regulators indexed by ID */ - struct palmas_reg_init **reg_init; + struct palmas_reg_init *reg_init[PALMAS_NUM_REGS]; /* use LDO6 for vibrator control */ int ldo6_vibrator; +}; +struct palmas_usb_platform_data { + /* Set this if platform wishes its own vbus control */ + int no_control_vbus; + /* Do we enable the wakeup comparator on probe */ + int wakeup; +}; + +struct palmas_resource_platform_data { + int regen1_mode_sleep; + int regen2_mode_sleep; + int sysen1_mode_sleep; + int sysen2_mode_sleep; + + /* bitfield to be loaded to NSLEEP_RES_ASSIGN */ + u8 nsleep_res; + /* bitfield to be loaded to NSLEEP_SMPS_ASSIGN */ + u8 nsleep_smps; + /* bitfield to be loaded to NSLEEP_LDO_ASSIGN1 */ + u8 nsleep_ldo1; + /* bitfield to be loaded to NSLEEP_LDO_ASSIGN2 */ + u8 nsleep_ldo2; + + /* bitfield to be loaded to ENABLE1_RES_ASSIGN */ + u8 enable1_res; + /* bitfield to be loaded to ENABLE1_SMPS_ASSIGN */ + u8 enable1_smps; + /* bitfield to be loaded to ENABLE1_LDO_ASSIGN1 */ + u8 enable1_ldo1; + /* bitfield to be loaded to ENABLE1_LDO_ASSIGN2 */ + u8 enable1_ldo2; + + /* bitfield to be loaded to ENABLE2_RES_ASSIGN */ + u8 enable2_res; + /* bitfield to be loaded to ENABLE2_SMPS_ASSIGN */ + u8 enable2_smps; + /* bitfield to be loaded to ENABLE2_LDO_ASSIGN1 */ + u8 enable2_ldo1; + /* bitfield to be loaded to ENABLE2_LDO_ASSIGN2 */ + u8 enable2_ldo2; +}; + +struct palmas_clk_platform_data { + int clk32kg_mode_sleep; + int clk32kgaudio_mode_sleep; }; struct palmas_platform_data { @@ -138,8 +234,49 @@ struct palmas_platform_data { u8 pad1, pad2; struct palmas_pmic_platform_data *pmic_pdata; + struct palmas_gpadc_platform_data *gpadc_pdata; + struct palmas_usb_platform_data *usb_pdata; + struct palmas_resource_platform_data *resource_pdata; + struct palmas_clk_platform_data *clk_pdata; +}; + +struct palmas_gpadc_calibration { + s32 gain; + s32 gain_error; + s32 offset_error; }; +struct palmas_gpadc { + struct device *dev; + struct palmas *palmas; + + int ch3_current; + int ch0_current; + + int gpadc_force; + + int bat_removal; + + struct mutex reading_lock; + struct completion irq_complete; + + int eoc_sw_irq; + + struct palmas_gpadc_calibration *palmas_cal_tbl; + + int conv0_channel; + int conv1_channel; + int rt_channel; +}; + +struct palmas_gpadc_result { + s32 raw_code; + s32 corrected_code; + s32 result; +}; + +#define PALMAS_MAX_CHANNELS 16 + /* Define the palmas IRQ numbers */ enum palmas_irqs { /* INT1 registers */ @@ -182,34 +319,6 @@ enum palmas_irqs { PALMAS_NUM_IRQ, }; -enum palmas_regulators { - /* SMPS regulators */ - PALMAS_REG_SMPS12, - PALMAS_REG_SMPS123, - PALMAS_REG_SMPS3, - PALMAS_REG_SMPS45, - PALMAS_REG_SMPS457, - PALMAS_REG_SMPS6, - PALMAS_REG_SMPS7, - PALMAS_REG_SMPS8, - PALMAS_REG_SMPS9, - PALMAS_REG_SMPS10, - /* LDO regulators */ - PALMAS_REG_LDO1, - PALMAS_REG_LDO2, - PALMAS_REG_LDO3, - PALMAS_REG_LDO4, - PALMAS_REG_LDO5, - PALMAS_REG_LDO6, - PALMAS_REG_LDO7, - PALMAS_REG_LDO8, - PALMAS_REG_LDO9, - PALMAS_REG_LDOLN, - PALMAS_REG_LDOUSB, - /* Total number of regulators */ - PALMAS_NUM_REGS, -}; - struct palmas_pmic { struct palmas *palmas; struct device *dev; @@ -223,6 +332,69 @@ struct palmas_pmic { int range[PALMAS_REG_SMPS10]; }; +struct palmas_resource { + struct palmas *palmas; + struct device *dev; +}; + +struct palmas_usb { + struct palmas *palmas; + struct device *dev; + + /* for vbus reporting with irqs disabled */ + spinlock_t lock; + + struct regulator *vbus_reg; + + /* used to set vbus, in atomic path */ + struct work_struct set_vbus_work; + + int irq1; + int irq2; + int irq3; + int irq4; + + int vbus_enable; + + u8 linkstat; +}; + +#define comparator_to_palmas(x) container_of((x), struct palmas_usb, comparator) + +enum usb_irq_events { + /* Wakeup events from INT3 */ + PALMAS_USB_ID_WAKEPUP, + PALMAS_USB_VBUS_WAKEUP, + + /* ID_OTG_EVENTS */ + PALMAS_USB_ID_GND, + N_PALMAS_USB_ID_GND, + PALMAS_USB_ID_C, + N_PALMAS_USB_ID_C, + PALMAS_USB_ID_B, + N_PALMAS_USB_ID_B, + PALMAS_USB_ID_A, + N_PALMAS_USB_ID_A, + PALMAS_USB_ID_FLOAT, + N_PALMAS_USB_ID_FLOAT, + + /* VBUS_OTG_EVENTS */ + PALMAS_USB_VB_SESS_END, + N_PALMAS_USB_VB_SESS_END, + PALMAS_USB_VB_SESS_VLD, + N_PALMAS_USB_VB_SESS_VLD, + PALMAS_USB_VA_SESS_VLD, + N_PALMAS_USB_VA_SESS_VLD, + PALMAS_USB_VA_VBUS_VLD, + N_PALMAS_USB_VA_VBUS_VLD, + PALMAS_USB_VADP_SNS, + N_PALMAS_USB_VADP_SNS, + PALMAS_USB_VADP_PRB, + N_PALMAS_USB_VADP_PRB, + PALMAS_USB_VOTG_SESS_VLD, + N_PALMAS_USB_VOTG_SESS_VLD, +}; + /* defines so we can store the mux settings */ #define PALMAS_GPIO_0_MUXED (1 << 0) #define PALMAS_GPIO_1_MUXED (1 << 1) diff --git a/include/linux/mfd/smsc.h b/include/linux/mfd/smsc.h new file mode 100644 index 000000000000..9747b29f356f --- /dev/null +++ b/include/linux/mfd/smsc.h @@ -0,0 +1,109 @@ +/* + * SMSC ECE1099 + * + * Copyright 2012 Texas Instruments Inc. + * + * Author: Sourav Poddar <sourav.poddar@ti.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +#ifndef __LINUX_MFD_SMSC_H +#define __LINUX_MFD_SMSC_H + +#include <linux/regmap.h> + +#define SMSC_ID_ECE1099 1 +#define SMSC_NUM_CLIENTS 2 + +#define SMSC_BASE_ADDR 0x38 +#define OMAP_GPIO_SMSC_IRQ 151 + +#define SMSC_MAXGPIO 32 +#define SMSC_BANK(offs) ((offs) >> 3) +#define SMSC_BIT(offs) (1u << ((offs) & 0x7)) + +struct smsc { + struct device *dev; + struct i2c_client *i2c_clients[SMSC_NUM_CLIENTS]; + struct regmap *regmap; + int clk; + /* Stored chip id */ + int id; +}; + +struct smsc_gpio; +struct smsc_keypad; + +static inline int smsc_read(struct device *child, unsigned int reg, + unsigned int *dest) +{ + struct smsc *smsc = dev_get_drvdata(child->parent); + + return regmap_read(smsc->regmap, reg, dest); +} + +static inline int smsc_write(struct device *child, unsigned int reg, + unsigned int value) +{ + struct smsc *smsc = dev_get_drvdata(child->parent); + + return regmap_write(smsc->regmap, reg, value); +} + +/* Registers for SMSC */ +#define SMSC_RESET 0xF5 +#define SMSC_GRP_INT 0xF9 +#define SMSC_CLK_CTRL 0xFA +#define SMSC_WKUP_CTRL 0xFB +#define SMSC_DEV_ID 0xFC +#define SMSC_DEV_REV 0xFD +#define SMSC_VEN_ID_L 0xFE +#define SMSC_VEN_ID_H 0xFF + +/* CLK VALUE */ +#define SMSC_CLK_VALUE 0x13 + +/* Registers for function GPIO INPUT */ +#define SMSC_GPIO_DATA_IN_START 0x00 + +/* Registers for function GPIO OUPUT */ +#define SMSC_GPIO_DATA_OUT_START 0x05 + +/* Definitions for SMSC GPIO CONFIGURATION REGISTER*/ +#define SMSC_GPIO_INPUT_LOW 0x01 +#define SMSC_GPIO_INPUT_RISING 0x09 +#define SMSC_GPIO_INPUT_FALLING 0x11 +#define SMSC_GPIO_INPUT_BOTH_EDGE 0x19 +#define SMSC_GPIO_OUTPUT_PP 0x21 +#define SMSC_GPIO_OUTPUT_OP 0x31 + +#define GRP_INT_STAT 0xf9 +#define SMSC_GPI_INT 0x0f +#define SMSC_CFG_START 0x0A + +/* Registers for SMSC GPIO INTERRUPT STATUS REGISTER*/ +#define SMSC_GPIO_INT_STAT_START 0x32 + +/* Registers for SMSC GPIO INTERRUPT MASK REGISTER*/ +#define SMSC_GPIO_INT_MASK_START 0x37 + +/* Registers for SMSC function KEYPAD*/ +#define SMSC_KP_OUT 0x40 +#define SMSC_KP_IN 0x41 +#define SMSC_KP_INT_STAT 0x42 +#define SMSC_KP_INT_MASK 0x43 + +/* Definitions for keypad */ +#define SMSC_KP_KSO 0x70 +#define SMSC_KP_KSI 0x51 +#define SMSC_KSO_ALL_LOW 0x20 +#define SMSC_KP_SET_LOW_PWR 0x0B +#define SMSC_KP_SET_HIGH 0xFF +#define SMSC_KSO_EVAL 0x00 + +#endif /* __LINUX_MFD_SMSC_H */ diff --git a/include/linux/mfd/syscon.h b/include/linux/mfd/syscon.h new file mode 100644 index 000000000000..6aeb6b8da64d --- /dev/null +++ b/include/linux/mfd/syscon.h @@ -0,0 +1,23 @@ +/* + * System Control Driver + * + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * Copyright (C) 2012 Linaro Ltd. + * + * Author: Dong Aisheng <dong.aisheng@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __LINUX_MFD_SYSCON_H__ +#define __LINUX_MFD_SYSCON_H__ + +extern struct regmap *syscon_node_to_regmap(struct device_node *np); +extern struct regmap *syscon_regmap_lookup_by_compatible(const char *s); +extern struct regmap *syscon_regmap_lookup_by_phandle( + struct device_node *np, + const char *property); +#endif /* __LINUX_MFD_SYSCON_H__ */ diff --git a/include/linux/mfd/syscon/imx6q-iomuxc-gpr.h b/include/linux/mfd/syscon/imx6q-iomuxc-gpr.h new file mode 100644 index 000000000000..dab34a1deb2c --- /dev/null +++ b/include/linux/mfd/syscon/imx6q-iomuxc-gpr.h @@ -0,0 +1,319 @@ +/* + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __LINUX_IMX6Q_IOMUXC_GPR_H +#define __LINUX_IMX6Q_IOMUXC_GPR_H + +#include <linux/bitops.h> + +#define IOMUXC_GPR0 0x00 +#define IOMUXC_GPR1 0x04 +#define IOMUXC_GPR2 0x08 +#define IOMUXC_GPR3 0x0c +#define IOMUXC_GPR4 0x10 +#define IOMUXC_GPR5 0x14 +#define IOMUXC_GPR6 0x18 +#define IOMUXC_GPR7 0x1c +#define IOMUXC_GPR8 0x20 +#define IOMUXC_GPR9 0x24 +#define IOMUXC_GPR10 0x28 +#define IOMUXC_GPR11 0x2c +#define IOMUXC_GPR12 0x30 +#define IOMUXC_GPR13 0x34 + +#define IMX6Q_GPR0_CLOCK_8_MUX_SEL_MASK (0x3 << 30) +#define IMX6Q_GPR0_CLOCK_8_MUX_SEL_AUDMUX_RXCLK_P7_MUXED (0x0 << 30) +#define IMX6Q_GPR0_CLOCK_8_MUX_SEL_AUDMUX_RXCLK_P7 (0x1 << 30) +#define IMX6Q_GPR0_CLOCK_8_MUX_SEL_SSI3_SSI_SRCK (0x2 << 30) +#define IMX6Q_GPR0_CLOCK_8_MUX_SEL_SSI3_RX_BIT_CLK (0x3 << 30) +#define IMX6Q_GPR0_CLOCK_0_MUX_SEL_MASK (0x3 << 28) +#define IMX6Q_GPR0_CLOCK_0_MUX_SEL_ESAI1_IPP_IND_SCKR_MUXED (0x0 << 28) +#define IMX6Q_GPR0_CLOCK_0_MUX_SEL_ESAI1_IPP_IND_SCKR (0x1 << 28) +#define IMX6Q_GPR0_CLOCK_0_MUX_SEL_ESAI1_IPP_DO_SCKR (0x2 << 28) +#define IMX6Q_GPR0_CLOCK_B_MUX_SEL_MASK (0x3 << 26) +#define IMX6Q_GPR0_CLOCK_B_MUX_SEL_AUDMUX_TXCLK_P7_MUXED (0x0 << 26) +#define IMX6Q_GPR0_CLOCK_B_MUX_SEL_AUDMUX_TXCLK_P7 (0x1 << 26) +#define IMX6Q_GPR0_CLOCK_B_MUX_SEL_SSI3_SSI_STCK (0x2 << 26) +#define IMX6Q_GPR0_CLOCK_B_MUX_SEL_SSI3_TX_BIT_CLK (0x3 << 26) +#define IMX6Q_GPR0_CLOCK_3_MUX_SEL_MASK (0x3 << 24) +#define IMX6Q_GPR0_CLOCK_3_MUX_SEL_AUDMUX_RXCLK_P7_MUXED (0x3 << 24) +#define IMX6Q_GPR0_CLOCK_3_MUX_SEL_AUDMUX_RXCLK_P7 (0x3 << 24) +#define IMX6Q_GPR0_CLOCK_3_MUX_SEL_SSI3_SSI_SRCK (0x3 << 24) +#define IMX6Q_GPR0_CLOCK_3_MUX_SEL_SSI3_RX_BIT_CLK (0x3 << 24) +#define IMX6Q_GPR0_CLOCK_A_MUX_SEL_MASK (0x3 << 22) +#define IMX6Q_GPR0_CLOCK_A_MUX_SEL_AUDMUX_TXCLK_P2_MUXED (0x0 << 22) +#define IMX6Q_GPR0_CLOCK_A_MUX_SEL_AUDMUX_TXCLK_P2 (0x1 << 22) +#define IMX6Q_GPR0_CLOCK_A_MUX_SEL_SSI2_SSI_STCK (0x2 << 22) +#define IMX6Q_GPR0_CLOCK_A_MUX_SEL_SSI2_TX_BIT_CLK (0x3 << 22) +#define IMX6Q_GPR0_CLOCK_2_MUX_SEL_MASK (0x3 << 20) +#define IMX6Q_GPR0_CLOCK_2_MUX_SEL_AUDMUX_RXCLK_P2_MUXED (0x0 << 20) +#define IMX6Q_GPR0_CLOCK_2_MUX_SEL_AUDMUX_RXCLK_P2 (0x1 << 20) +#define IMX6Q_GPR0_CLOCK_2_MUX_SEL_SSI2_SSI_SRCK (0x2 << 20) +#define IMX6Q_GPR0_CLOCK_2_MUX_SEL_SSI2_RX_BIT_CLK (0x3 << 20) +#define IMX6Q_GPR0_CLOCK_9_MUX_SEL_MASK (0x3 << 18) +#define IMX6Q_GPR0_CLOCK_9_MUX_SEL_AUDMUX_TXCLK_P1_MUXED (0x0 << 18) +#define IMX6Q_GPR0_CLOCK_9_MUX_SEL_AUDMUX_TXCLK_P1 (0x1 << 18) +#define IMX6Q_GPR0_CLOCK_9_MUX_SEL_SSI1_SSI_STCK (0x2 << 18) +#define IMX6Q_GPR0_CLOCK_9_MUX_SEL_SSI1_SSI_TX_BIT_CLK (0x3 << 18) +#define IMX6Q_GPR0_CLOCK_1_MUX_SEL_MASK (0x3 << 16) +#define IMX6Q_GPR0_CLOCK_1_MUX_SEL_AUDMUX_RXCLK_P1_MUXED (0x0 << 16) +#define IMX6Q_GPR0_CLOCK_1_MUX_SEL_AUDMUX_RXCLK_P1 (0x1 << 16) +#define IMX6Q_GPR0_CLOCK_1_MUX_SEL_SSI1_SSI_SRCK (0x2 << 16) +#define IMX6Q_GPR0_CLOCK_1_MUX_SEL_SSI1_SSI_RX_BIT_CLK (0x3 << 16) +#define IMX6Q_GPR0_TX_CLK2_MUX_SEL_MASK (0x3 << 14) +#define IMX6Q_GPR0_TX_CLK2_MUX_SEL_ASRCK_CLK1 (0x0 << 14) +#define IMX6Q_GPR0_TX_CLK2_MUX_SEL_ASRCK_CLK2 (0x1 << 14) +#define IMX6Q_GPR0_TX_CLK2_MUX_SEL_ASRCK_CLK3 (0x2 << 14) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL7_MASK BIT(7) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL7_SPDIF 0x0 +#define IMX6Q_GPR0_DMAREQ_MUX_SEL7_IOMUX BIT(7) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL6_MASK BIT(6) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL6_ESAI 0x0 +#define IMX6Q_GPR0_DMAREQ_MUX_SEL6_I2C3 BIT(6) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL5_MASK BIT(5) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL5_ECSPI4 0x0 +#define IMX6Q_GPR0_DMAREQ_MUX_SEL5_EPIT2 BIT(5) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL4_MASK BIT(4) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL4_ECSPI4 0x0 +#define IMX6Q_GPR0_DMAREQ_MUX_SEL4_I2C1 BIT(4) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL3_MASK BIT(3) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL3_ECSPI2 0x0 +#define IMX6Q_GPR0_DMAREQ_MUX_SEL3_I2C1 BIT(3) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL2_MASK BIT(2) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL2_ECSPI1 0x0 +#define IMX6Q_GPR0_DMAREQ_MUX_SEL2_I2C2 BIT(2) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL1_MASK BIT(1) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL1_ECSPI1 0x0 +#define IMX6Q_GPR0_DMAREQ_MUX_SEL1_I2C3 BIT(1) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL0_MASK BIT(0) +#define IMX6Q_GPR0_DMAREQ_MUX_SEL0_IPU1 0x0 +#define IMX6Q_GPR0_DMAREQ_MUX_SEL0_IOMUX BIT(0) + +#define IMX6Q_GPR1_PCIE_REQ_MASK (0x3 << 30) +#define IMX6Q_GPR1_PCIE_EXIT_L1 BIT(28) +#define IMX6Q_GPR1_PCIE_RDY_L23 BIT(27) +#define IMX6Q_GPR1_PCIE_ENTER_L1 BIT(26) +#define IMX6Q_GPR1_MIPI_COLOR_SW BIT(25) +#define IMX6Q_GPR1_DPI_OFF BIT(24) +#define IMX6Q_GPR1_EXC_MON_MASK BIT(22) +#define IMX6Q_GPR1_EXC_MON_OKAY 0x0 +#define IMX6Q_GPR1_EXC_MON_SLVE BIT(22) +#define IMX6Q_GPR1_MIPI_IPU2_SEL_MASK BIT(21) +#define IMX6Q_GPR1_MIPI_IPU2_SEL_GASKET 0x0 +#define IMX6Q_GPR1_MIPI_IPU2_SEL_IOMUX BIT(21) +#define IMX6Q_GPR1_MIPI_IPU1_MUX_MASK BIT(20) +#define IMX6Q_GPR1_MIPI_IPU1_MUX_GASKET 0x0 +#define IMX6Q_GPR1_MIPI_IPU1_MUX_IOMUX BIT(20) +#define IMX6Q_GPR1_MIPI_IPU2_MUX_MASK BIT(19) +#define IMX6Q_GPR1_MIPI_IPU2_MUX_GASKET 0x0 +#define IMX6Q_GPR1_MIPI_IPU2_MUX_IOMUX BIT(19) +#define IMX6Q_GPR1_PCIE_TEST_PD BIT(18) +#define IMX6Q_GPR1_IPU_VPU_MUX_MASK BIT(17) +#define IMX6Q_GPR1_IPU_VPU_MUX_IPU1 0x0 +#define IMX6Q_GPR1_IPU_VPU_MUX_IPU2 BIT(17) +#define IMX6Q_GPR1_PCIE_REF_CLK_EN BIT(16) +#define IMX6Q_GPR1_USB_EXP_MODE BIT(15) +#define IMX6Q_GPR1_PCIE_INT BIT(14) +#define IMX6Q_GPR1_USB_OTG_ID_SEL_MASK BIT(13) +#define IMX6Q_GPR1_USB_OTG_ID_SEL_ENET_RX_ER 0x0 +#define IMX6Q_GPR1_USB_OTG_ID_SEL_GPIO_1 BIT(13) +#define IMX6Q_GPR1_GINT BIT(12) +#define IMX6Q_GPR1_ADDRS3_MASK (0x3 << 10) +#define IMX6Q_GPR1_ADDRS3_32MB (0x0 << 10) +#define IMX6Q_GPR1_ADDRS3_64MB (0x1 << 10) +#define IMX6Q_GPR1_ADDRS3_128MB (0x2 << 10) +#define IMX6Q_GPR1_ACT_CS3 BIT(9) +#define IMX6Q_GPR1_ADDRS2_MASK (0x3 << 7) +#define IMX6Q_GPR1_ACT_CS2 BIT(6) +#define IMX6Q_GPR1_ADDRS1_MASK (0x3 << 4) +#define IMX6Q_GPR1_ACT_CS1 BIT(3) +#define IMX6Q_GPR1_ADDRS0_MASK (0x3 << 1) +#define IMX6Q_GPR1_ACT_CS0 BIT(0) + +#define IMX6Q_GPR2_COUNTER_RESET_VAL_MASK (0x3 << 20) +#define IMX6Q_GPR2_COUNTER_RESET_VAL_5 (0x0 << 20) +#define IMX6Q_GPR2_COUNTER_RESET_VAL_3 (0x1 << 20) +#define IMX6Q_GPR2_COUNTER_RESET_VAL_4 (0x2 << 20) +#define IMX6Q_GPR2_COUNTER_RESET_VAL_6 (0x3 << 20) +#define IMX6Q_GPR2_LVDS_CLK_SHIFT_MASK (0x7 << 16) +#define IMX6Q_GPR2_LVDS_CLK_SHIFT_0 (0x0 << 16) +#define IMX6Q_GPR2_LVDS_CLK_SHIFT_1 (0x1 << 16) +#define IMX6Q_GPR2_LVDS_CLK_SHIFT_2 (0x2 << 16) +#define IMX6Q_GPR2_LVDS_CLK_SHIFT_3 (0x3 << 16) +#define IMX6Q_GPR2_LVDS_CLK_SHIFT_4 (0x4 << 16) +#define IMX6Q_GPR2_LVDS_CLK_SHIFT_5 (0x5 << 16) +#define IMX6Q_GPR2_LVDS_CLK_SHIFT_6 (0x6 << 16) +#define IMX6Q_GPR2_LVDS_CLK_SHIFT_7 (0x7 << 16) +#define IMX6Q_GPR2_BGREF_RRMODE_MASK BIT(15) +#define IMX6Q_GPR2_BGREF_RRMODE_EXT_RESISTOR 0x0 +#define IMX6Q_GPR2_BGREF_RRMODE_INT_RESISTOR BIT(15) +#define IMX6Q_GPR2_DI1_VS_POLARITY_MASK BIT(10) +#define IMX6Q_GPR2_DI1_VS_POLARITY_ACTIVE_H 0x0 +#define IMX6Q_GPR2_DI1_VS_POLARITY_ACTIVE_L BIT(10) +#define IMX6Q_GPR2_DI0_VS_POLARITY_MASK BIT(9) +#define IMX6Q_GPR2_DI0_VS_POLARITY_ACTIVE_H 0x0 +#define IMX6Q_GPR2_DI0_VS_POLARITY_ACTIVE_L BIT(9) +#define IMX6Q_GPR2_BIT_MAPPING_CH1_MASK BIT(8) +#define IMX6Q_GPR2_BIT_MAPPING_CH1_SPWG 0x0 +#define IMX6Q_GPR2_BIT_MAPPING_CH1_JEIDA BIT(8) +#define IMX6Q_GPR2_DATA_WIDTH_CH1_MASK BIT(7) +#define IMX6Q_GPR2_DATA_WIDTH_CH1_18BIT 0x0 +#define IMX6Q_GPR2_DATA_WIDTH_CH1_24BIT BIT(7) +#define IMX6Q_GPR2_BIT_MAPPING_CH0_MASK BIT(6) +#define IMX6Q_GPR2_BIT_MAPPING_CH0_SPWG 0x0 +#define IMX6Q_GPR2_BIT_MAPPING_CH0_JEIDA BIT(6) +#define IMX6Q_GPR2_DATA_WIDTH_CH0_MASK BIT(5) +#define IMX6Q_GPR2_DATA_WIDTH_CH0_18BIT 0x0 +#define IMX6Q_GPR2_DATA_WIDTH_CH0_24BIT BIT(5) +#define IMX6Q_GPR2_SPLIT_MODE_EN BIT(4) +#define IMX6Q_GPR2_CH1_MODE_MASK (0x3 << 2) +#define IMX6Q_GPR2_CH1_MODE_DISABLE (0x0 << 2) +#define IMX6Q_GPR2_CH1_MODE_EN_ROUTE_DI0 (0x1 << 2) +#define IMX6Q_GPR2_CH1_MODE_EN_ROUTE_DI1 (0x3 << 2) +#define IMX6Q_GPR2_CH0_MODE_MASK (0x3 << 0) +#define IMX6Q_GPR2_CH0_MODE_DISABLE (0x0 << 0) +#define IMX6Q_GPR2_CH0_MODE_EN_ROUTE_DI0 (0x1 << 0) +#define IMX6Q_GPR2_CH0_MODE_EN_ROUTE_DI1 (0x3 << 0) + +#define IMX6Q_GPR3_GPU_DBG_MASK (0x3 << 29) +#define IMX6Q_GPR3_GPU_DBG_GPU3D (0x0 << 29) +#define IMX6Q_GPR3_GPU_DBG_GPU2D (0x1 << 29) +#define IMX6Q_GPR3_GPU_DBG_OPENVG (0x2 << 29) +#define IMX6Q_GPR3_BCH_WR_CACHE_CTL BIT(28) +#define IMX6Q_GPR3_BCH_RD_CACHE_CTL BIT(27) +#define IMX6Q_GPR3_USDHCX_WR_CACHE_CTL BIT(26) +#define IMX6Q_GPR3_USDHCX_RD_CACHE_CTL BIT(25) +#define IMX6Q_GPR3_OCRAM_CTL_MASK (0xf << 21) +#define IMX6Q_GPR3_OCRAM_STATUS_MASK (0xf << 17) +#define IMX6Q_GPR3_CORE3_DBG_ACK_EN BIT(16) +#define IMX6Q_GPR3_CORE2_DBG_ACK_EN BIT(15) +#define IMX6Q_GPR3_CORE1_DBG_ACK_EN BIT(14) +#define IMX6Q_GPR3_CORE0_DBG_ACK_EN BIT(13) +#define IMX6Q_GPR3_TZASC2_BOOT_LOCK BIT(12) +#define IMX6Q_GPR3_TZASC1_BOOT_LOCK BIT(11) +#define IMX6Q_GPR3_IPU_DIAG_MASK BIT(10) +#define IMX6Q_GPR3_LVDS1_MUX_CTL_MASK (0x3 << 8) +#define IMX6Q_GPR3_LVDS1_MUX_CTL_IPU1_DI0 (0x0 << 8) +#define IMX6Q_GPR3_LVDS1_MUX_CTL_IPU1_DI1 (0x1 << 8) +#define IMX6Q_GPR3_LVDS1_MUX_CTL_IPU2_DI0 (0x2 << 8) +#define IMX6Q_GPR3_LVDS1_MUX_CTL_IPU2_DI1 (0x3 << 8) +#define IMX6Q_GPR3_LVDS0_MUX_CTL_MASK (0x3 << 6) +#define IMX6Q_GPR3_LVDS0_MUX_CTL_IPU1_DI0 (0x0 << 6) +#define IMX6Q_GPR3_LVDS0_MUX_CTL_IPU1_DI1 (0x1 << 6) +#define IMX6Q_GPR3_LVDS0_MUX_CTL_IPU2_DI0 (0x2 << 6) +#define IMX6Q_GPR3_LVDS0_MUX_CTL_IPU2_DI1 (0x3 << 6) +#define IMX6Q_GPR3_MIPI_MUX_CTL_MASK (0x3 << 4) +#define IMX6Q_GPR3_MIPI_MUX_CTL_IPU1_DI0 (0x0 << 4) +#define IMX6Q_GPR3_MIPI_MUX_CTL_IPU1_DI1 (0x1 << 4) +#define IMX6Q_GPR3_MIPI_MUX_CTL_IPU2_DI0 (0x2 << 4) +#define IMX6Q_GPR3_MIPI_MUX_CTL_IPU2_DI1 (0x3 << 4) +#define IMX6Q_GPR3_HDMI_MUX_CTL_MASK (0x3 << 2) +#define IMX6Q_GPR3_HDMI_MUX_CTL_IPU1_DI0 (0x0 << 2) +#define IMX6Q_GPR3_HDMI_MUX_CTL_IPU1_DI1 (0x1 << 2) +#define IMX6Q_GPR3_HDMI_MUX_CTL_IPU2_DI0 (0x2 << 2) +#define IMX6Q_GPR3_HDMI_MUX_CTL_IPU2_DI1 (0x3 << 2) + +#define IMX6Q_GPR4_VDOA_WR_CACHE_SEL BIT(31) +#define IMX6Q_GPR4_VDOA_RD_CACHE_SEL BIT(30) +#define IMX6Q_GPR4_VDOA_WR_CACHE_VAL BIT(29) +#define IMX6Q_GPR4_VDOA_RD_CACHE_VAL BIT(28) +#define IMX6Q_GPR4_PCIE_WR_CACHE_SEL BIT(27) +#define IMX6Q_GPR4_PCIE_RD_CACHE_SEL BIT(26) +#define IMX6Q_GPR4_PCIE_WR_CACHE_VAL BIT(25) +#define IMX6Q_GPR4_PCIE_RD_CACHE_VAL BIT(24) +#define IMX6Q_GPR4_SDMA_STOP_ACK BIT(19) +#define IMX6Q_GPR4_CAN2_STOP_ACK BIT(18) +#define IMX6Q_GPR4_CAN1_STOP_ACK BIT(17) +#define IMX6Q_GPR4_ENET_STOP_ACK BIT(16) +#define IMX6Q_GPR4_SOC_VERSION_MASK (0xff << 8) +#define IMX6Q_GPR4_SOC_VERSION_OFF 0x8 +#define IMX6Q_GPR4_VPU_WR_CACHE_SEL BIT(7) +#define IMX6Q_GPR4_VPU_RD_CACHE_SEL BIT(6) +#define IMX6Q_GPR4_VPU_P_WR_CACHE_VAL BIT(3) +#define IMX6Q_GPR4_VPU_P_RD_CACHE_VAL_MASK BIT(2) +#define IMX6Q_GPR4_IPU_WR_CACHE_CTL BIT(1) +#define IMX6Q_GPR4_IPU_RD_CACHE_CTL BIT(0) + +#define IMX6Q_GPR5_L2_CLK_STOP BIT(8) + +#define IMX6Q_GPR9_TZASC2_BYP BIT(1) +#define IMX6Q_GPR9_TZASC1_BYP BIT(0) + +#define IMX6Q_GPR10_LOCK_DBG_EN BIT(29) +#define IMX6Q_GPR10_LOCK_DBG_CLK_EN BIT(28) +#define IMX6Q_GPR10_LOCK_SEC_ERR_RESP BIT(27) +#define IMX6Q_GPR10_LOCK_OCRAM_TZ_ADDR (0x3f << 21) +#define IMX6Q_GPR10_LOCK_OCRAM_TZ_EN BIT(20) +#define IMX6Q_GPR10_LOCK_DCIC2_MUX_MASK (0x3 << 18) +#define IMX6Q_GPR10_LOCK_DCIC1_MUX_MASK (0x3 << 16) +#define IMX6Q_GPR10_DBG_EN BIT(13) +#define IMX6Q_GPR10_DBG_CLK_EN BIT(12) +#define IMX6Q_GPR10_SEC_ERR_RESP_MASK BIT(11) +#define IMX6Q_GPR10_SEC_ERR_RESP_OKEY 0x0 +#define IMX6Q_GPR10_SEC_ERR_RESP_SLVE BIT(11) +#define IMX6Q_GPR10_OCRAM_TZ_ADDR_MASK (0x3f << 5) +#define IMX6Q_GPR10_OCRAM_TZ_EN_MASK BIT(4) +#define IMX6Q_GPR10_DCIC2_MUX_CTL_MASK (0x3 << 2) +#define IMX6Q_GPR10_DCIC2_MUX_CTL_IPU1_DI0 (0x0 << 2) +#define IMX6Q_GPR10_DCIC2_MUX_CTL_IPU1_DI1 (0x1 << 2) +#define IMX6Q_GPR10_DCIC2_MUX_CTL_IPU2_DI0 (0x2 << 2) +#define IMX6Q_GPR10_DCIC2_MUX_CTL_IPU2_DI1 (0x3 << 2) +#define IMX6Q_GPR10_DCIC1_MUX_CTL_MASK (0x3 << 0) +#define IMX6Q_GPR10_DCIC1_MUX_CTL_IPU1_DI0 (0x0 << 0) +#define IMX6Q_GPR10_DCIC1_MUX_CTL_IPU1_DI1 (0x1 << 0) +#define IMX6Q_GPR10_DCIC1_MUX_CTL_IPU2_DI0 (0x2 << 0) +#define IMX6Q_GPR10_DCIC1_MUX_CTL_IPU2_DI1 (0x3 << 0) + +#define IMX6Q_GPR12_ARMP_IPG_CLK_EN BIT(27) +#define IMX6Q_GPR12_ARMP_AHB_CLK_EN BIT(26) +#define IMX6Q_GPR12_ARMP_ATB_CLK_EN BIT(25) +#define IMX6Q_GPR12_ARMP_APB_CLK_EN BIT(24) +#define IMX6Q_GPR12_PCIE_CTL_2 BIT(10) + +#define IMX6Q_GPR13_SDMA_STOP_REQ BIT(30) +#define IMX6Q_GPR13_CAN2_STOP_REQ BIT(29) +#define IMX6Q_GPR13_CAN1_STOP_REQ BIT(28) +#define IMX6Q_GPR13_ENET_STOP_REQ BIT(27) +#define IMX6Q_GPR13_SATA_PHY_8_MASK (0x7 << 24) +#define IMX6Q_GPR13_SATA_PHY_8_0_5_DB (0x0 << 24) +#define IMX6Q_GPR13_SATA_PHY_8_1_0_DB (0x1 << 24) +#define IMX6Q_GPR13_SATA_PHY_8_1_5_DB (0x2 << 24) +#define IMX6Q_GPR13_SATA_PHY_8_2_0_DB (0x3 << 24) +#define IMX6Q_GPR13_SATA_PHY_8_2_5_DB (0x4 << 24) +#define IMX6Q_GPR13_SATA_PHY_8_3_0_DB (0x5 << 24) +#define IMX6Q_GPR13_SATA_PHY_8_3_5_DB (0x6 << 24) +#define IMX6Q_GPR13_SATA_PHY_8_4_0_DB (0x7 << 24) +#define IMX6Q_GPR13_SATA_PHY_7_MASK (0x1f << 19) +#define IMX6Q_GPR13_SATA_PHY_7_SATA1I (0x10 << 19) +#define IMX6Q_GPR13_SATA_PHY_7_SATA1M (0x10 << 19) +#define IMX6Q_GPR13_SATA_PHY_7_SATA1X (0x1a << 19) +#define IMX6Q_GPR13_SATA_PHY_7_SATA2I (0x12 << 19) +#define IMX6Q_GPR13_SATA_PHY_7_SATA2M (0x12 << 19) +#define IMX6Q_GPR13_SATA_PHY_7_SATA2X (0x1a << 19) +#define IMX6Q_GPR13_SATA_PHY_6_MASK (0x7 << 16) +#define IMX6Q_GPR13_SATA_SPEED_MASK BIT(15) +#define IMX6Q_GPR13_SATA_SPEED_1P5G 0x0 +#define IMX6Q_GPR13_SATA_SPEED_3P0G BIT(15) +#define IMX6Q_GPR13_SATA_PHY_5 BIT(14) +#define IMX6Q_GPR13_SATA_PHY_4_MASK (0x7 << 11) +#define IMX6Q_GPR13_SATA_PHY_4_16_16 (0x0 << 11) +#define IMX6Q_GPR13_SATA_PHY_4_14_16 (0x1 << 11) +#define IMX6Q_GPR13_SATA_PHY_4_12_16 (0x2 << 11) +#define IMX6Q_GPR13_SATA_PHY_4_10_16 (0x3 << 11) +#define IMX6Q_GPR13_SATA_PHY_4_9_16 (0x4 << 11) +#define IMX6Q_GPR13_SATA_PHY_4_8_16 (0x5 << 11) +#define IMX6Q_GPR13_SATA_PHY_3_MASK (0xf << 7) +#define IMX6Q_GPR13_SATA_PHY_3_OFF 0x7 +#define IMX6Q_GPR13_SATA_PHY_2_MASK (0x1f << 2) +#define IMX6Q_GPR13_SATA_PHY_2_OFF 0x2 +#define IMX6Q_GPR13_SATA_PHY_1_MASK (0x3 << 0) +#define IMX6Q_GPR13_SATA_PHY_1_FAST (0x0 << 0) +#define IMX6Q_GPR13_SATA_PHY_1_MED (0x1 << 0) +#define IMX6Q_GPR13_SATA_PHY_1_SLOW (0x2 << 0) + +#endif /* __LINUX_IMX6Q_IOMUXC_GPR_H */ diff --git a/include/linux/mfd/tc3589x.h b/include/linux/mfd/tc3589x.h index 3acb3a8e3af5..6b8e1ff4672b 100644 --- a/include/linux/mfd/tc3589x.h +++ b/include/linux/mfd/tc3589x.h @@ -117,6 +117,7 @@ struct tc3589x { struct mutex lock; struct device *dev; struct i2c_client *i2c; + struct irq_domain *domain; int irq_base; int num_gpio; diff --git a/include/linux/mfd/tps65217.h b/include/linux/mfd/tps65217.h index 7cd83d826ed8..290762f93930 100644 --- a/include/linux/mfd/tps65217.h +++ b/include/linux/mfd/tps65217.h @@ -213,6 +213,23 @@ enum tps65217_regulator_id { /* Number of total regulators available */ #define TPS65217_NUM_REGULATOR (TPS65217_NUM_DCDC + TPS65217_NUM_LDO) +enum tps65217_bl_isel { + TPS65217_BL_ISET1 = 1, + TPS65217_BL_ISET2, +}; + +enum tps65217_bl_fdim { + TPS65217_BL_FDIM_100HZ, + TPS65217_BL_FDIM_200HZ, + TPS65217_BL_FDIM_500HZ, + TPS65217_BL_FDIM_1000HZ, +}; + +struct tps65217_bl_pdata { + enum tps65217_bl_isel isel; + enum tps65217_bl_fdim fdim; +}; + /** * struct tps65217_board - packages regulator init data * @tps65217_regulator_data: regulator initialization values @@ -222,6 +239,7 @@ enum tps65217_regulator_id { struct tps65217_board { struct regulator_init_data *tps65217_init_data[TPS65217_NUM_REGULATOR]; struct device_node *of_node[TPS65217_NUM_REGULATOR]; + struct tps65217_bl_pdata *bl_pdata; }; /** diff --git a/include/linux/mfd/tps6586x.h b/include/linux/mfd/tps6586x.h index 94514710a03f..2dd123194958 100644 --- a/include/linux/mfd/tps6586x.h +++ b/include/linux/mfd/tps6586x.h @@ -78,6 +78,7 @@ struct tps6586x_platform_data { int gpio_base; int irq_base; + bool pm_off; }; /* diff --git a/include/linux/mfd/tps65910.h b/include/linux/mfd/tps65910.h index 9bf8767818b4..ac772b36a1b1 100644 --- a/include/linux/mfd/tps65910.h +++ b/include/linux/mfd/tps65910.h @@ -366,6 +366,8 @@ /*Register DEVCTRL (0x80) register.RegisterDescription */ +#define DEVCTRL_PWR_OFF_MASK 0x80 +#define DEVCTRL_PWR_OFF_SHIFT 7 #define DEVCTRL_RTC_PWDN_MASK 0x40 #define DEVCTRL_RTC_PWDN_SHIFT 6 #define DEVCTRL_CK32K_CTRL_MASK 0x20 @@ -809,6 +811,7 @@ struct tps65910_board { int vmbch2_threshold; bool en_ck32k_xtal; bool en_dev_slp; + bool pm_off; struct tps65910_sleep_keepon_data *slp_keepon; bool en_gpio_sleep[TPS6591X_MAX_NUM_GPIO]; unsigned long regulator_ext_sleep_control[TPS65910_NUM_REGS]; diff --git a/include/linux/mfd/twl6040.h b/include/linux/mfd/twl6040.h index ba43d4806b83..a8eff4ad9be5 100644 --- a/include/linux/mfd/twl6040.h +++ b/include/linux/mfd/twl6040.h @@ -143,7 +143,7 @@ #define TWL6040_GPO1 0x01 #define TWL6040_GPO2 0x02 -#define TWL6040_GPO3 0x03 +#define TWL6040_GPO3 0x04 /* ACCCTL (0x2D) fields */ @@ -158,7 +158,7 @@ #define TWL6040_VIBROCDET 0x20 #define TWL6040_TSHUTDET 0x40 -#define TWL6040_CELLS 2 +#define TWL6040_CELLS 3 #define TWL6040_REV_ES1_0 0x00 #define TWL6040_REV_ES1_1 0x01 /* Rev ES1.1 and ES1.2 */ @@ -176,6 +176,8 @@ #define TWL6040_SYSCLK_SEL_LPPLL 0 #define TWL6040_SYSCLK_SEL_HPPLL 1 +#define TWL6040_GPO_MAX 3 + struct twl6040_codec_data { u16 hs_left_step; u16 hs_right_step; @@ -192,11 +194,16 @@ struct twl6040_vibra_data { int vddvibr_uV; /* VDDVIBR volt, set 0 for fixed reg */ }; +struct twl6040_gpo_data { + int gpio_base; +}; + struct twl6040_platform_data { int audpwron_gpio; /* audio power-on gpio */ struct twl6040_codec_data *codec; struct twl6040_vibra_data *vibra; + struct twl6040_gpo_data *gpo; }; struct regmap; diff --git a/include/linux/of.h b/include/linux/of.h index f594c528842f..72843b72a2b2 100644 --- a/include/linux/of.h +++ b/include/linux/of.h @@ -317,6 +317,12 @@ static inline const char* of_node_full_name(struct device_node *np) return "<no-node>"; } +static inline struct device_node *of_find_node_by_name(struct device_node *from, + const char *name) +{ + return NULL; +} + static inline bool of_have_populated_dt(void) { return false; |