diff options
Diffstat (limited to 'include/linux/platform_data')
| -rw-r--r-- | include/linux/platform_data/atmel.h | 73 | ||||
| -rw-r--r-- | include/linux/platform_data/gpio-omap.h | 1 | ||||
| -rw-r--r-- | include/linux/platform_data/iommu-omap.h | 49 | ||||
| -rw-r--r-- | include/linux/platform_data/leds-omap.h | 22 | ||||
| -rw-r--r-- | include/linux/platform_data/mmc-omap.h | 151 | ||||
| -rw-r--r-- | include/linux/platform_data/mtd-nand-omap2.h | 46 | ||||
| -rw-r--r-- | include/linux/platform_data/mtd-onenand-omap2.h | 28 | ||||
| -rw-r--r-- | include/linux/platform_data/usb-omap.h | 80 |
8 files changed, 413 insertions, 37 deletions
diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h index b0f2c56a8ea2..6a293b7fff3b 100644 --- a/include/linux/platform_data/atmel.h +++ b/include/linux/platform_data/atmel.h @@ -8,6 +8,55 @@ #define __ATMEL_H__ #include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/device.h> +#include <linux/i2c.h> +#include <linux/leds.h> +#include <linux/spi/spi.h> +#include <linux/usb/atmel_usba_udc.h> +#include <linux/atmel-mci.h> +#include <sound/atmel-ac97c.h> +#include <linux/serial.h> +#include <linux/platform_data/macb.h> + +/* + * at91: 6 USARTs and one DBGU port (SAM9260) + * avr32: 4 + */ +#define ATMEL_MAX_UART 7 + + /* USB Device */ +struct at91_udc_data { + int vbus_pin; /* high == host powering us */ + u8 vbus_active_low; /* vbus polarity */ + u8 vbus_polled; /* Use polling, not interrupt */ + int pullup_pin; /* active == D+ pulled up */ + u8 pullup_active_low; /* true == pullup_pin is active low */ +}; + + /* Compact Flash */ +struct at91_cf_data { + int irq_pin; /* I/O IRQ */ + int det_pin; /* Card detect */ + int vcc_pin; /* power switching */ + int rst_pin; /* card reset */ + u8 chipselect; /* EBI Chip Select number */ + u8 flags; +#define AT91_CF_TRUE_IDE 0x01 +#define AT91_IDE_SWAP_A0_A2 0x02 +}; + + /* USB Host */ +#define AT91_MAX_USBH_PORTS 3 +struct at91_usbh_data { + int vbus_pin[AT91_MAX_USBH_PORTS]; /* port power-control pin */ + int overcurrent_pin[AT91_MAX_USBH_PORTS]; + u8 ports; /* number of ports on root hub */ + u8 overcurrent_supported; + u8 vbus_pin_active_low[AT91_MAX_USBH_PORTS]; + u8 overcurrent_status[AT91_MAX_USBH_PORTS]; + u8 overcurrent_changed[AT91_MAX_USBH_PORTS]; +}; /* NAND / SmartMedia */ struct atmel_nand_data { @@ -24,4 +73,28 @@ struct atmel_nand_data { unsigned int num_parts; }; + /* Serial */ +struct atmel_uart_data { + int num; /* port num */ + short use_dma_tx; /* use transmit DMA? */ + short use_dma_rx; /* use receive DMA? */ + void __iomem *regs; /* virt. base address, if any */ + struct serial_rs485 rs485; /* rs485 settings */ +}; + + /* Touchscreen Controller */ +struct at91_tsadcc_data { + unsigned int adc_clock; + u8 pendet_debounce; + u8 ts_sample_hold_time; +}; + +/* CAN */ +struct at91_can_data { + void (*transceiver_switch)(int on); +}; + +/* FIXME: this needs a better location, but gets stuff building again */ +extern int at91_suspend_entering_slow_clock(void); + #endif /* __ATMEL_H__ */ diff --git a/include/linux/platform_data/gpio-omap.h b/include/linux/platform_data/gpio-omap.h index e8741c2678d5..5d50b25a73d7 100644 --- a/include/linux/platform_data/gpio-omap.h +++ b/include/linux/platform_data/gpio-omap.h @@ -26,7 +26,6 @@ #include <linux/io.h> #include <linux/platform_device.h> -#include <mach/irqs.h> #define OMAP1_MPUIO_BASE 0xfffb5000 diff --git a/include/linux/platform_data/iommu-omap.h b/include/linux/platform_data/iommu-omap.h new file mode 100644 index 000000000000..c677b9f2fefa --- /dev/null +++ b/include/linux/platform_data/iommu-omap.h @@ -0,0 +1,49 @@ +/* + * omap iommu: main structures + * + * Copyright (C) 2008-2009 Nokia Corporation + * + * Written by Hiroshi DOYU <Hiroshi.DOYU@nokia.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#define MMU_REG_SIZE 256 + +/** + * struct iommu_arch_data - omap iommu private data + * @name: name of the iommu device + * @iommu_dev: handle of the iommu device + * + * This is an omap iommu private data object, which binds an iommu user + * to its iommu device. This object should be placed at the iommu user's + * dev_archdata so generic IOMMU API can be used without having to + * utilize omap-specific plumbing anymore. + */ +struct omap_iommu_arch_data { + const char *name; + struct omap_iommu *iommu_dev; +}; + +/** + * struct omap_mmu_dev_attr - OMAP mmu device attributes for omap_hwmod + * @da_start: device address where the va space starts. + * @da_end: device address where the va space ends. + * @nr_tlb_entries: number of entries supported by the translation + * look-aside buffer (TLB). + */ +struct omap_mmu_dev_attr { + u32 da_start; + u32 da_end; + int nr_tlb_entries; +}; + +struct iommu_platform_data { + const char *name; + const char *clk_name; + const int nr_tlb_entries; + u32 da_start; + u32 da_end; +}; diff --git a/include/linux/platform_data/leds-omap.h b/include/linux/platform_data/leds-omap.h new file mode 100644 index 000000000000..56c9b2a0ada5 --- /dev/null +++ b/include/linux/platform_data/leds-omap.h @@ -0,0 +1,22 @@ +/* + * Copyright (C) 2006 Samsung Electronics + * Kyungmin Park <kyungmin.park@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef ASMARM_ARCH_LED_H +#define ASMARM_ARCH_LED_H + +struct omap_led_config { + struct led_classdev cdev; + s16 gpio; +}; + +struct omap_led_platform_data { + s16 nr_leds; + struct omap_led_config *leds; +}; + +#endif diff --git a/include/linux/platform_data/mmc-omap.h b/include/linux/platform_data/mmc-omap.h new file mode 100644 index 000000000000..2bf1b30cb5dc --- /dev/null +++ b/include/linux/platform_data/mmc-omap.h @@ -0,0 +1,151 @@ +/* + * MMC definitions for OMAP2 + * + * Copyright (C) 2006 Nokia Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#define OMAP_MMC_MAX_SLOTS 2 + +/* + * struct omap_mmc_dev_attr.flags possibilities + * + * OMAP_HSMMC_SUPPORTS_DUAL_VOLT: Some HSMMC controller instances can + * operate with either 1.8Vdc or 3.0Vdc card voltages; this flag + * should be set if this is the case. See for example Section 22.5.3 + * "MMC/SD/SDIO1 Bus Voltage Selection" of the OMAP34xx Multimedia + * Device Silicon Revision 3.1.x Revision ZR (July 2011) (SWPU223R). + * + * OMAP_HSMMC_BROKEN_MULTIBLOCK_READ: Multiple-block read transfers + * don't work correctly on some MMC controller instances on some + * OMAP3 SoCs; this flag should be set if this is the case. See + * for example Advisory 2.1.1.128 "MMC: Multiple Block Read + * Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_ + * Revision F (October 2010) (SPRZ278F). + */ +#define OMAP_HSMMC_SUPPORTS_DUAL_VOLT BIT(0) +#define OMAP_HSMMC_BROKEN_MULTIBLOCK_READ BIT(1) + +struct mmc_card; + +struct omap_mmc_dev_attr { + u8 flags; +}; + +struct omap_mmc_platform_data { + /* back-link to device */ + struct device *dev; + + /* number of slots per controller */ + unsigned nr_slots:2; + + /* set if your board has components or wiring that limits the + * maximum frequency on the MMC bus */ + unsigned int max_freq; + + /* switch the bus to a new slot */ + int (*switch_slot)(struct device *dev, int slot); + /* initialize board-specific MMC functionality, can be NULL if + * not supported */ + int (*init)(struct device *dev); + void (*cleanup)(struct device *dev); + void (*shutdown)(struct device *dev); + + /* To handle board related suspend/resume functionality for MMC */ + int (*suspend)(struct device *dev, int slot); + int (*resume)(struct device *dev, int slot); + + /* Return context loss count due to PM states changing */ + int (*get_context_loss_count)(struct device *dev); + + /* Integrating attributes from the omap_hwmod layer */ + u8 controller_flags; + + /* Register offset deviation */ + u16 reg_offset; + + struct omap_mmc_slot_data { + + /* + * 4/8 wires and any additional host capabilities + * need to OR'd all capabilities (ref. linux/mmc/host.h) + */ + u8 wires; /* Used for the MMC driver on omap1 and 2420 */ + u32 caps; /* Used for the MMC driver on 2430 and later */ + u32 pm_caps; /* PM capabilities of the mmc */ + + /* + * nomux means "standard" muxing is wrong on this board, and + * that board-specific code handled it before common init logic. + */ + unsigned nomux:1; + + /* switch pin can be for card detect (default) or card cover */ + unsigned cover:1; + + /* use the internal clock */ + unsigned internal_clock:1; + + /* nonremovable e.g. eMMC */ + unsigned nonremovable:1; + + /* Try to sleep or power off when possible */ + unsigned power_saving:1; + + /* If using power_saving and the MMC power is not to go off */ + unsigned no_off:1; + + /* eMMC does not handle power off when not in sleep state */ + unsigned no_regulator_off_init:1; + + /* Regulator off remapped to sleep */ + unsigned vcc_aux_disable_is_sleep:1; + + /* we can put the features above into this variable */ +#define HSMMC_HAS_PBIAS (1 << 0) +#define HSMMC_HAS_UPDATED_RESET (1 << 1) +#define HSMMC_HAS_HSPE_SUPPORT (1 << 2) +#define MMC_OMAP7XX (1 << 3) +#define MMC_OMAP15XX (1 << 4) +#define MMC_OMAP16XX (1 << 5) + unsigned features; + + int switch_pin; /* gpio (card detect) */ + int gpio_wp; /* gpio (write protect) */ + + int (*set_bus_mode)(struct device *dev, int slot, int bus_mode); + int (*set_power)(struct device *dev, int slot, + int power_on, int vdd); + int (*get_ro)(struct device *dev, int slot); + void (*remux)(struct device *dev, int slot, int power_on); + /* Call back before enabling / disabling regulators */ + void (*before_set_reg)(struct device *dev, int slot, + int power_on, int vdd); + /* Call back after enabling / disabling regulators */ + void (*after_set_reg)(struct device *dev, int slot, + int power_on, int vdd); + /* if we have special card, init it using this callback */ + void (*init_card)(struct mmc_card *card); + + /* return MMC cover switch state, can be NULL if not supported. + * + * possible return values: + * 0 - closed + * 1 - open + */ + int (*get_cover_state)(struct device *dev, int slot); + + const char *name; + u32 ocr_mask; + + /* Card detection IRQs */ + int card_detect_irq; + int (*card_detect)(struct device *dev, int slot); + + unsigned int ban_openended:1; + + } slots[OMAP_MMC_MAX_SLOTS]; +}; diff --git a/include/linux/platform_data/mtd-nand-omap2.h b/include/linux/platform_data/mtd-nand-omap2.h index 1a68c1e5fe53..24d32ca34bef 100644 --- a/include/linux/platform_data/mtd-nand-omap2.h +++ b/include/linux/platform_data/mtd-nand-omap2.h @@ -8,9 +8,13 @@ * published by the Free Software Foundation. */ -#include <plat/gpmc.h> +#ifndef _MTD_NAND_OMAP2_H +#define _MTD_NAND_OMAP2_H + #include <linux/mtd/partitions.h> +#define GPMC_BCH_NUM_REMAINDER 8 + enum nand_io { NAND_OMAP_PREFETCH_POLLED = 0, /* prefetch polled mode, default */ NAND_OMAP_POLLED, /* polled mode, without prefetch */ @@ -18,10 +22,38 @@ enum nand_io { NAND_OMAP_PREFETCH_IRQ /* prefetch enabled irq mode */ }; +enum omap_ecc { + /* 1-bit ecc: stored at end of spare area */ + OMAP_ECC_HAMMING_CODE_DEFAULT = 0, /* Default, s/w method */ + OMAP_ECC_HAMMING_CODE_HW, /* gpmc to detect the error */ + /* 1-bit ecc: stored at beginning of spare area as romcode */ + OMAP_ECC_HAMMING_CODE_HW_ROMCODE, /* gpmc method & romcode layout */ + OMAP_ECC_BCH4_CODE_HW, /* 4-bit BCH ecc code */ + OMAP_ECC_BCH8_CODE_HW, /* 8-bit BCH ecc code */ +}; + +struct gpmc_nand_regs { + void __iomem *gpmc_status; + void __iomem *gpmc_nand_command; + void __iomem *gpmc_nand_address; + void __iomem *gpmc_nand_data; + void __iomem *gpmc_prefetch_config1; + void __iomem *gpmc_prefetch_config2; + void __iomem *gpmc_prefetch_control; + void __iomem *gpmc_prefetch_status; + void __iomem *gpmc_ecc_config; + void __iomem *gpmc_ecc_control; + void __iomem *gpmc_ecc_size_config; + void __iomem *gpmc_ecc1_result; + void __iomem *gpmc_bch_result0[GPMC_BCH_NUM_REMAINDER]; + void __iomem *gpmc_bch_result1[GPMC_BCH_NUM_REMAINDER]; + void __iomem *gpmc_bch_result2[GPMC_BCH_NUM_REMAINDER]; + void __iomem *gpmc_bch_result3[GPMC_BCH_NUM_REMAINDER]; +}; + struct omap_nand_platform_data { int cs; struct mtd_partition *parts; - struct gpmc_timings *gpmc_t; int nr_parts; bool dev_ready; enum nand_io xfer_type; @@ -30,14 +62,4 @@ struct omap_nand_platform_data { struct gpmc_nand_regs reg; }; -/* minimum size for IO mapping */ -#define NAND_IO_SIZE 4 - -#if defined(CONFIG_MTD_NAND_OMAP2) || defined(CONFIG_MTD_NAND_OMAP2_MODULE) -extern int gpmc_nand_init(struct omap_nand_platform_data *d); -#else -static inline int gpmc_nand_init(struct omap_nand_platform_data *d) -{ - return 0; -} #endif diff --git a/include/linux/platform_data/mtd-onenand-omap2.h b/include/linux/platform_data/mtd-onenand-omap2.h index 2858667d2e4f..685af7e8b120 100644 --- a/include/linux/platform_data/mtd-onenand-omap2.h +++ b/include/linux/platform_data/mtd-onenand-omap2.h @@ -9,17 +9,15 @@ * published by the Free Software Foundation. */ +#ifndef __MTD_ONENAND_OMAP2_H +#define __MTD_ONENAND_OMAP2_H + #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> #define ONENAND_SYNC_READ (1 << 0) #define ONENAND_SYNC_READWRITE (1 << 1) - -struct onenand_freq_info { - u16 maf_id; - u16 dev_id; - u16 ver_id; -}; +#define ONENAND_IN_OMAP34XX (1 << 2) struct omap_onenand_platform_data { int cs; @@ -27,27 +25,9 @@ struct omap_onenand_platform_data { struct mtd_partition *parts; int nr_parts; int (*onenand_setup)(void __iomem *, int *freq_ptr); - int (*get_freq)(const struct onenand_freq_info *freq_info, - bool *clk_dep); int dma_channel; u8 flags; u8 regulator_can_sleep; u8 skip_initial_unlocking; }; - -#define ONENAND_MAX_PARTITIONS 8 - -#if defined(CONFIG_MTD_ONENAND_OMAP2) || \ - defined(CONFIG_MTD_ONENAND_OMAP2_MODULE) - -extern void gpmc_onenand_init(struct omap_onenand_platform_data *d); - -#else - -#define board_onenand_data NULL - -static inline void gpmc_onenand_init(struct omap_onenand_platform_data *d) -{ -} - #endif diff --git a/include/linux/platform_data/usb-omap.h b/include/linux/platform_data/usb-omap.h new file mode 100644 index 000000000000..8570bcfe6311 --- /dev/null +++ b/include/linux/platform_data/usb-omap.h @@ -0,0 +1,80 @@ +/* + * usb-omap.h - Platform data for the various OMAP USB IPs + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com + * + * This software is distributed under the terms of the GNU General Public + * License ("GPL") version 2, as published by the Free Software Foundation. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + */ + +#define OMAP3_HS_USB_PORTS 3 + +enum usbhs_omap_port_mode { + OMAP_USBHS_PORT_MODE_UNUSED, + OMAP_EHCI_PORT_MODE_PHY, + OMAP_EHCI_PORT_MODE_TLL, + OMAP_EHCI_PORT_MODE_HSIC, + OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0, + OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM, + OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0, + OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM, + OMAP_OHCI_PORT_MODE_TLL_6PIN_DATSE0, + OMAP_OHCI_PORT_MODE_TLL_6PIN_DPDM, + OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0, + OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM, + OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0, + OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM +}; + +struct usbtll_omap_platform_data { + enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS]; +}; + +struct ehci_hcd_omap_platform_data { + enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS]; + int reset_gpio_port[OMAP3_HS_USB_PORTS]; + struct regulator *regulator[OMAP3_HS_USB_PORTS]; + unsigned phy_reset:1; +}; + +struct ohci_hcd_omap_platform_data { + enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS]; + unsigned es2_compatibility:1; +}; + +struct usbhs_omap_platform_data { + enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS]; + + struct ehci_hcd_omap_platform_data *ehci_data; + struct ohci_hcd_omap_platform_data *ohci_data; +}; + +/*-------------------------------------------------------------------------*/ + +struct omap_musb_board_data { + u8 interface_type; + u8 mode; + u16 power; + unsigned extvbus:1; + void (*set_phy_power)(u8 on); + void (*clear_irq)(void); + void (*set_mode)(u8 mode); + void (*reset)(void); +}; + +enum musb_interface { + MUSB_INTERFACE_ULPI, + MUSB_INTERFACE_UTMI +}; |