diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/net/Space.c | 8 | ||||
| -rw-r--r-- | drivers/net/ethernet/i825xx/Kconfig | 27 | ||||
| -rw-r--r-- | drivers/net/ethernet/i825xx/Makefile | 2 | ||||
| -rw-r--r-- | drivers/net/ethernet/i825xx/eepro.c | 1822 | ||||
| -rw-r--r-- | drivers/net/ethernet/i825xx/eexpress.c | 1661 | ||||
| -rw-r--r-- | drivers/net/ethernet/i825xx/eexpress.h | 179 |
6 files changed, 0 insertions, 3699 deletions
diff --git a/drivers/net/Space.c b/drivers/net/Space.c index ac66a6af7138..726b17b79610 100644 --- a/drivers/net/Space.c +++ b/drivers/net/Space.c @@ -44,8 +44,6 @@ extern struct net_device *el2_probe(int unit); extern struct net_device *ne_probe(int unit); extern struct net_device *hp_probe(int unit); extern struct net_device *hp_plus_probe(int unit); -extern struct net_device *express_probe(int unit); -extern struct net_device *eepro_probe(int unit); extern struct net_device *at1700_probe(int unit); extern struct net_device *fmv18x_probe(int unit); extern struct net_device *eth16i_probe(int unit); @@ -150,12 +148,6 @@ static struct devprobe2 isa_probes[] __initdata = { #ifdef CONFIG_ETH16I {eth16i_probe, 0}, /* ICL EtherTeam 16i/32 */ #endif -#ifdef CONFIG_EEXPRESS /* Intel EtherExpress */ - {express_probe, 0}, -#endif -#ifdef CONFIG_EEXPRESS_PRO /* Intel EtherExpress Pro/10 */ - {eepro_probe, 0}, -#endif #ifdef CONFIG_EWRK3 /* DEC EtherWORKS 3 */ {ewrk3_probe, 0}, #endif diff --git a/drivers/net/ethernet/i825xx/Kconfig b/drivers/net/ethernet/i825xx/Kconfig index b800a94fc875..16b14a93c205 100644 --- a/drivers/net/ethernet/i825xx/Kconfig +++ b/drivers/net/ethernet/i825xx/Kconfig @@ -36,33 +36,6 @@ config BVME6000_NET in your kernel. To compile this driver as a module, choose M here. -config EEXPRESS - tristate "EtherExpress 16 support" - depends on ISA - ---help--- - If you have an EtherExpress16 network (Ethernet) card, say Y and - read the Ethernet-HOWTO, available from - <http://www.tldp.org/docs.html#howto>. Note that the Intel - EtherExpress16 card used to be regarded as a very poor choice - because the driver was very unreliable. We now have a new driver - that should do better. - - To compile this driver as a module, choose M here. The module - will be called eexpress. - -config EEXPRESS_PRO - tristate "EtherExpressPro support/EtherExpress 10 (i82595) support" - depends on ISA - ---help--- - If you have a network (Ethernet) card of this type, say Y. This - driver supports Intel i82595{FX,TX} based boards. Note however - that the EtherExpress PRO/100 Ethernet card has its own separate - driver. Please read the Ethernet-HOWTO, available from - <http://www.tldp.org/docs.html#howto>. - - To compile this driver as a module, choose M here. The module - will be called eepro. - config LASI_82596 tristate "Lasi ethernet" depends on GSC diff --git a/drivers/net/ethernet/i825xx/Makefile b/drivers/net/ethernet/i825xx/Makefile index bc81e14ed5bd..4267ae72c5d2 100644 --- a/drivers/net/ethernet/i825xx/Makefile +++ b/drivers/net/ethernet/i825xx/Makefile @@ -3,8 +3,6 @@ # obj-$(CONFIG_ARM_ETHER1) += ether1.o -obj-$(CONFIG_EEXPRESS) += eexpress.o -obj-$(CONFIG_EEXPRESS_PRO) += eepro.o obj-$(CONFIG_NI52) += ni52.o obj-$(CONFIG_SUN3_82586) += sun3_82586.o obj-$(CONFIG_ZNET) += znet.o diff --git a/drivers/net/ethernet/i825xx/eepro.c b/drivers/net/ethernet/i825xx/eepro.c deleted file mode 100644 index 7f49fd54c521..000000000000 --- a/drivers/net/ethernet/i825xx/eepro.c +++ /dev/null @@ -1,1822 +0,0 @@ -/* eepro.c: Intel EtherExpress Pro/10 device driver for Linux. */ -/* - Written 1994, 1995,1996 by Bao C. Ha. - - Copyright (C) 1994, 1995,1996 by Bao C. Ha. - - This software may be used and distributed - according to the terms of the GNU General Public License, - incorporated herein by reference. - - The author may be reached at bao.ha@srs.gov - or 418 Hastings Place, Martinez, GA 30907. - - Things remaining to do: - Better record keeping of errors. - Eliminate transmit interrupt to reduce overhead. - Implement "concurrent processing". I won't be doing it! - - Bugs: - - If you have a problem of not detecting the 82595 during a - reboot (warm reset), disable the FLASH memory should fix it. - This is a compatibility hardware problem. - - Versions: - 0.13b basic ethtool support (aris, 09/13/2004) - 0.13a in memory shortage, drop packets also in board - (Michael Westermann <mw@microdata-pos.de>, 07/30/2002) - 0.13 irq sharing, rewrote probe function, fixed a nasty bug in - hardware_send_packet and a major cleanup (aris, 11/08/2001) - 0.12d fixing a problem with single card detected as eight eth devices - fixing a problem with sudden drop in card performance - (chris (asdn@go2.pl), 10/29/2001) - 0.12c fixing some problems with old cards (aris, 01/08/2001) - 0.12b misc fixes (aris, 06/26/2000) - 0.12a port of version 0.12a of 2.2.x kernels to 2.3.x - (aris (aris@conectiva.com.br), 05/19/2000) - 0.11e some tweaks about multiple cards support (PdP, jul/aug 1999) - 0.11d added __initdata, __init stuff; call spin_lock_init - in eepro_probe1. Replaced "eepro" by dev->name. Augmented - the code protected by spin_lock in interrupt routine - (PdP, 12/12/1998) - 0.11c minor cleanup (PdP, RMC, 09/12/1998) - 0.11b Pascal Dupuis (dupuis@lei.ucl.ac.be): works as a module - under 2.1.xx. Debug messages are flagged as KERN_DEBUG to - avoid console flooding. Added locking at critical parts. Now - the dawn thing is SMP safe. - 0.11a Attempt to get 2.1.xx support up (RMC) - 0.11 Brian Candler added support for multiple cards. Tested as - a module, no idea if it works when compiled into kernel. - - 0.10e Rick Bressler notified me that ifconfig up;ifconfig down fails - because the irq is lost somewhere. Fixed that by moving - request_irq and free_irq to eepro_open and eepro_close respectively. - 0.10d Ugh! Now Wakeup works. Was seriously broken in my first attempt. - I'll need to find a way to specify an ioport other than - the default one in the PnP case. PnP definitively sucks. - And, yes, this is not the only reason. - 0.10c PnP Wakeup Test for 595FX. uncomment #define PnPWakeup; - to use. - 0.10b Should work now with (some) Pro/10+. At least for - me (and my two cards) it does. _No_ guarantee for - function with non-Pro/10+ cards! (don't have any) - (RMC, 9/11/96) - - 0.10 Added support for the Etherexpress Pro/10+. The - IRQ map was changed significantly from the old - pro/10. The new interrupt map was provided by - Rainer M. Canavan (Canavan@Zeus.cs.bonn.edu). - (BCH, 9/3/96) - - 0.09 Fixed a race condition in the transmit algorithm, - which causes crashes under heavy load with fast - pentium computers. The performance should also - improve a bit. The size of RX buffer, and hence - TX buffer, can also be changed via lilo or insmod. - (BCH, 7/31/96) - - 0.08 Implement 32-bit I/O for the 82595TX and 82595FX - based lan cards. Disable full-duplex mode if TPE - is not used. (BCH, 4/8/96) - - 0.07a Fix a stat report which counts every packet as a - heart-beat failure. (BCH, 6/3/95) - - 0.07 Modified to support all other 82595-based lan cards. - The IRQ vector of the EtherExpress Pro will be set - according to the value saved in the EEPROM. For other - cards, I will do autoirq_request() to grab the next - available interrupt vector. (BCH, 3/17/95) - - 0.06a,b Interim released. Minor changes in the comments and - print out format. (BCH, 3/9/95 and 3/14/95) - - 0.06 First stable release that I am comfortable with. (BCH, - 3/2/95) - - 0.05 Complete testing of multicast. (BCH, 2/23/95) - - 0.04 Adding multicast support. (BCH, 2/14/95) - - 0.03 First widely alpha release for public testing. - (BCH, 2/14/95) - -*/ - -static const char version[] = - "eepro.c: v0.13b 09/13/2004 aris@cathedrallabs.org\n"; - -#include <linux/module.h> - -/* - Sources: - - This driver wouldn't have been written without the availability - of the Crynwr's Lan595 driver source code. It helps me to - familiarize with the 82595 chipset while waiting for the Intel - documentation. I also learned how to detect the 82595 using - the packet driver's technique. - - This driver is written by cutting and pasting the skeleton.c driver - provided by Donald Becker. I also borrowed the EEPROM routine from - Donald Becker's 82586 driver. - - Datasheet for the Intel 82595 (including the TX and FX version). It - provides just enough info that the casual reader might think that it - documents the i82595. - - The User Manual for the 82595. It provides a lot of the missing - information. - -*/ - -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/fcntl.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/in.h> -#include <linux/string.h> -#include <linux/errno.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/skbuff.h> -#include <linux/spinlock.h> -#include <linux/init.h> -#include <linux/delay.h> -#include <linux/bitops.h> -#include <linux/ethtool.h> - -#include <asm/io.h> -#include <asm/dma.h> - -#define DRV_NAME "eepro" -#define DRV_VERSION "0.13c" - -#define compat_dev_kfree_skb( skb, mode ) dev_kfree_skb( (skb) ) -/* I had reports of looong delays with SLOW_DOWN defined as udelay(2) */ -#define SLOW_DOWN inb(0x80) -/* udelay(2) */ -#define compat_init_data __initdata -enum iftype { AUI=0, BNC=1, TPE=2 }; - -/* First, a few definitions that the brave might change. */ -/* A zero-terminated list of I/O addresses to be probed. */ -static unsigned int eepro_portlist[] compat_init_data = - { 0x300, 0x210, 0x240, 0x280, 0x2C0, 0x200, 0x320, 0x340, 0x360, 0}; -/* note: 0x300 is default, the 595FX supports ALL IO Ports - from 0x000 to 0x3F0, some of which are reserved in PCs */ - -/* To try the (not-really PnP Wakeup: */ -/* -#define PnPWakeup -*/ - -/* use 0 for production, 1 for verification, >2 for debug */ -#ifndef NET_DEBUG -#define NET_DEBUG 0 -#endif -static unsigned int net_debug = NET_DEBUG; - -/* The number of low I/O ports used by the ethercard. */ -#define EEPRO_IO_EXTENT 16 - -/* Different 82595 chips */ -#define LAN595 0 -#define LAN595TX 1 -#define LAN595FX 2 -#define LAN595FX_10ISA 3 - -/* Information that need to be kept for each board. */ -struct eepro_local { - unsigned rx_start; - unsigned tx_start; /* start of the transmit chain */ - int tx_last; /* pointer to last packet in the transmit chain */ - unsigned tx_end; /* end of the transmit chain (plus 1) */ - int eepro; /* 1 for the EtherExpress Pro/10, - 2 for the EtherExpress Pro/10+, - 3 for the EtherExpress 10 (blue cards), - 0 for other 82595-based lan cards. */ - int version; /* a flag to indicate if this is a TX or FX - version of the 82595 chip. */ - int stepping; - - spinlock_t lock; /* Serializing lock */ - - unsigned rcv_ram; /* pre-calculated space for rx */ - unsigned xmt_ram; /* pre-calculated space for tx */ - unsigned char xmt_bar; - unsigned char xmt_lower_limit_reg; - unsigned char xmt_upper_limit_reg; - short xmt_lower_limit; - short xmt_upper_limit; - short rcv_lower_limit; - short rcv_upper_limit; - unsigned char eeprom_reg; - unsigned short word[8]; -}; - -/* The station (ethernet) address prefix, used for IDing the board. */ -#define SA_ADDR0 0x00 /* Etherexpress Pro/10 */ -#define SA_ADDR1 0xaa -#define SA_ADDR2 0x00 - -#define GetBit(x,y) ((x & (1<<y))>>y) - -/* EEPROM Word 0: */ -#define ee_PnP 0 /* Plug 'n Play enable bit */ -#define ee_Word1 1 /* Word 1? */ -#define ee_BusWidth 2 /* 8/16 bit */ -#define ee_FlashAddr 3 /* Flash Address */ -#define ee_FlashMask 0x7 /* Mask */ -#define ee_AutoIO 6 /* */ -#define ee_reserved0 7 /* =0! */ -#define ee_Flash 8 /* Flash there? */ -#define ee_AutoNeg 9 /* Auto Negotiation enabled? */ -#define ee_IO0 10 /* IO Address LSB */ -#define ee_IO0Mask 0x /*...*/ -#define ee_IO1 15 /* IO MSB */ - -/* EEPROM Word 1: */ -#define ee_IntSel 0 /* Interrupt */ -#define ee_IntMask 0x7 -#define ee_LI 3 /* Link Integrity 0= enabled */ -#define ee_PC 4 /* Polarity Correction 0= enabled */ -#define ee_TPE_AUI 5 /* PortSelection 1=TPE */ -#define ee_Jabber 6 /* Jabber prevention 0= enabled */ -#define ee_AutoPort 7 /* Auto Port Selection 1= Disabled */ -#define ee_SMOUT 8 /* SMout Pin Control 0= Input */ -#define ee_PROM 9 /* Flash EPROM / PROM 0=Flash */ -#define ee_reserved1 10 /* .. 12 =0! */ -#define ee_AltReady 13 /* Alternate Ready, 0=normal */ -#define ee_reserved2 14 /* =0! */ -#define ee_Duplex 15 - -/* Word2,3,4: */ -#define ee_IA5 0 /*bit start for individual Addr Byte 5 */ -#define ee_IA4 8 /*bit start for individual Addr Byte 5 */ -#define ee_IA3 0 /*bit start for individual Addr Byte 5 */ -#define ee_IA2 8 /*bit start for individual Addr Byte 5 */ -#define ee_IA1 0 /*bit start for individual Addr Byte 5 */ -#define ee_IA0 8 /*bit start for individual Addr Byte 5 */ - -/* Word 5: */ -#define ee_BNC_TPE 0 /* 0=TPE */ -#define ee_BootType 1 /* 00=None, 01=IPX, 10=ODI, 11=NDIS */ -#define ee_BootTypeMask 0x3 -#define ee_NumConn 3 /* Number of Connections 0= One or Two */ -#define ee_FlashSock 4 /* Presence of Flash Socket 0= Present */ -#define ee_PortTPE 5 -#define ee_PortBNC 6 -#define ee_PortAUI 7 -#define ee_PowerMgt 10 /* 0= disabled */ -#define ee_CP 13 /* Concurrent Processing */ -#define ee_CPMask 0x7 - -/* Word 6: */ -#define ee_Stepping 0 /* Stepping info */ -#define ee_StepMask 0x0F -#define ee_BoardID 4 /* Manucaturer Board ID, reserved */ -#define ee_BoardMask 0x0FFF - -/* Word 7: */ -#define ee_INT_TO_IRQ 0 /* int to IRQ Mapping = 0x1EB8 for Pro/10+ */ -#define ee_FX_INT2IRQ 0x1EB8 /* the _only_ mapping allowed for FX chips */ - -/*..*/ -#define ee_SIZE 0x40 /* total EEprom Size */ -#define ee_Checksum 0xBABA /* initial and final value for adding checksum */ - - -/* Card identification via EEprom: */ -#define ee_addr_vendor 0x10 /* Word offset for EISA Vendor ID */ -#define ee_addr_id 0x11 /* Word offset for Card ID */ -#define ee_addr_SN 0x12 /* Serial Number */ -#define ee_addr_CRC_8 0x14 /* CRC over last thee Bytes */ - - -#define ee_vendor_intel0 0x25 /* Vendor ID Intel */ -#define ee_vendor_intel1 0xD4 -#define ee_id_eepro10p0 0x10 /* ID for eepro/10+ */ -#define ee_id_eepro10p1 0x31 - -#define TX_TIMEOUT ((4*HZ)/10) - -/* Index to functions, as function prototypes. */ - -static int eepro_probe1(struct net_device *dev, int autoprobe); -static int eepro_open(struct net_device *dev); -static netdev_tx_t eepro_send_packet(struct sk_buff *skb, - struct net_device *dev); -static irqreturn_t eepro_interrupt(int irq, void *dev_id); -static void eepro_rx(struct net_device *dev); -static void eepro_transmit_interrupt(struct net_device *dev); -static int eepro_close(struct net_device *dev); -static void set_multicast_list(struct net_device *dev); -static void eepro_tx_timeout (struct net_device *dev); - -static int read_eeprom(int ioaddr, int location, struct net_device *dev); -static int hardware_send_packet(struct net_device *dev, void *buf, short length); -static int eepro_grab_irq(struct net_device *dev); - -/* - Details of the i82595. - -You will need either the datasheet or the user manual to understand what -is going on here. The 82595 is very different from the 82586, 82593. - -The receive algorithm in eepro_rx() is just an implementation of the -RCV ring structure that the Intel 82595 imposes at the hardware level. -The receive buffer is set at 24K, and the transmit buffer is 8K. I -am assuming that the total buffer memory is 32K, which is true for the -Intel EtherExpress Pro/10. If it is less than that on a generic card, -the driver will be broken. - -The transmit algorithm in the hardware_send_packet() is similar to the -one in the eepro_rx(). The transmit buffer is a ring linked list. -I just queue the next available packet to the end of the list. In my -system, the 82595 is so fast that the list seems to always contain a -single packet. In other systems with faster computers and more congested -network traffics, the ring linked list should improve performance by -allowing up to 8K worth of packets to be queued. - -The sizes of the receive and transmit buffers can now be changed via lilo -or insmod. Lilo uses the appended line "ether=io,irq,debug,rx-buffer,eth0" -where rx-buffer is in KB unit. Modules uses the parameter mem which is -also in KB unit, for example "insmod io=io-address irq=0 mem=rx-buffer." -The receive buffer has to be more than 3K or less than 29K. Otherwise, -it is reset to the default of 24K, and, hence, 8K for the trasnmit -buffer (transmit-buffer = 32K - receive-buffer). - -*/ -#define RAM_SIZE 0x8000 - -#define RCV_HEADER 8 -#define RCV_DEFAULT_RAM 0x6000 - -#define XMT_HEADER 8 -#define XMT_DEFAULT_RAM (RAM_SIZE - RCV_DEFAULT_RAM) - -#define XMT_START_PRO RCV_DEFAULT_RAM -#define XMT_START_10 0x0000 -#define RCV_START_PRO 0x0000 -#define RCV_START_10 XMT_DEFAULT_RAM - -#define RCV_DONE 0x0008 -#define RX_OK 0x2000 -#define RX_ERROR 0x0d81 - -#define TX_DONE_BIT 0x0080 -#define TX_OK 0x2000 -#define CHAIN_BIT 0x8000 -#define XMT_STATUS 0x02 -#define XMT_CHAIN 0x04 -#define XMT_COUNT 0x06 - -#define BANK0_SELECT 0x00 -#define BANK1_SELECT 0x40 -#define BANK2_SELECT 0x80 - -/* Bank 0 registers */ -#define COMMAND_REG 0x00 /* Register 0 */ -#define MC_SETUP 0x03 -#define XMT_CMD 0x04 -#define DIAGNOSE_CMD 0x07 -#define RCV_ENABLE_CMD 0x08 -#define RCV_DISABLE_CMD 0x0a -#define STOP_RCV_CMD 0x0b -#define RESET_CMD 0x0e -#define POWER_DOWN_CMD 0x18 -#define RESUME_XMT_CMD 0x1c -#define SEL_RESET_CMD 0x1e -#define STATUS_REG 0x01 /* Register 1 */ -#define RX_INT 0x02 -#define TX_INT 0x04 -#define EXEC_STATUS 0x30 -#define ID_REG 0x02 /* Register 2 */ -#define R_ROBIN_BITS 0xc0 /* round robin counter */ -#define ID_REG_MASK 0x2c -#define ID_REG_SIG 0x24 -#define AUTO_ENABLE 0x10 -#define INT_MASK_REG 0x03 /* Register 3 */ -#define RX_STOP_MASK 0x01 -#define RX_MASK 0x02 -#define TX_MASK 0x04 -#define EXEC_MASK 0x08 -#define ALL_MASK 0x0f -#define IO_32_BIT 0x10 -#define RCV_BAR 0x04 /* The following are word (16-bit) registers */ -#define RCV_STOP 0x06 - -#define XMT_BAR_PRO 0x0a -#define XMT_BAR_10 0x0b - -#define HOST_ADDRESS_REG 0x0c -#define IO_PORT 0x0e -#define IO_PORT_32_BIT 0x0c - -/* Bank 1 registers */ -#define REG1 0x01 -#define WORD_WIDTH 0x02 -#define INT_ENABLE 0x80 -#define INT_NO_REG 0x02 -#define RCV_LOWER_LIMIT_REG 0x08 -#define RCV_UPPER_LIMIT_REG 0x09 - -#define XMT_LOWER_LIMIT_REG_PRO 0x0a -#define XMT_UPPER_LIMIT_REG_PRO 0x0b -#define XMT_LOWER_LIMIT_REG_10 0x0b -#define XMT_UPPER_LIMIT_REG_10 0x0a - -/* Bank 2 registers */ -#define XMT_Chain_Int 0x20 /* Interrupt at the end of the transmit chain */ -#define XMT_Chain_ErrStop 0x40 /* Interrupt at the end of the chain even if there are errors */ -#define RCV_Discard_BadFrame 0x80 /* Throw bad frames away, and continue to receive others */ -#define REG2 0x02 -#define PRMSC_Mode 0x01 -#define Multi_IA 0x20 -#define REG3 0x03 -#define TPE_BIT 0x04 -#define BNC_BIT 0x20 -#define REG13 0x0d -#define FDX 0x00 -#define A_N_ENABLE 0x02 - -#define I_ADD_REG0 0x04 -#define I_ADD_REG1 0x05 -#define I_ADD_REG2 0x06 -#define I_ADD_REG3 0x07 -#define I_ADD_REG4 0x08 -#define I_ADD_REG5 0x09 - -#define EEPROM_REG_PRO 0x0a -#define EEPROM_REG_10 0x0b - -#define EESK 0x01 -#define EECS 0x02 -#define EEDI 0x04 -#define EEDO 0x08 - -/* do a full reset */ -#define eepro_reset(ioaddr) outb(RESET_CMD, ioaddr) - -/* do a nice reset */ -#define eepro_sel_reset(ioaddr) { \ - outb(SEL_RESET_CMD, ioaddr); \ - SLOW_DOWN; \ - SLOW_DOWN; \ - } - -/* disable all interrupts */ -#define eepro_dis_int(ioaddr) outb(ALL_MASK, ioaddr + INT_MASK_REG) - -/* clear all interrupts */ -#define eepro_clear_int(ioaddr) outb(ALL_MASK, ioaddr + STATUS_REG) - -/* enable tx/rx */ -#define eepro_en_int(ioaddr) outb(ALL_MASK & ~(RX_MASK | TX_MASK), \ - ioaddr + INT_MASK_REG) - -/* enable exec event interrupt */ -#define eepro_en_intexec(ioaddr) outb(ALL_MASK & ~(EXEC_MASK), ioaddr + INT_MASK_REG) - -/* enable rx */ -#define eepro_en_rx(ioaddr) outb(RCV_ENABLE_CMD, ioaddr) - -/* disable rx */ -#define eepro_dis_rx(ioaddr) outb(RCV_DISABLE_CMD, ioaddr) - -/* switch bank */ -#define eepro_sw2bank0(ioaddr) outb(BANK0_SELECT, ioaddr) -#define eepro_sw2bank1(ioaddr) outb(BANK1_SELECT, ioaddr) -#define eepro_sw2bank2(ioaddr) outb(BANK2_SELECT, ioaddr) - -/* enable interrupt line */ -#define eepro_en_intline(ioaddr) outb(inb(ioaddr + REG1) | INT_ENABLE,\ - ioaddr + REG1) - -/* disable interrupt line */ -#define eepro_dis_intline(ioaddr) outb(inb(ioaddr + REG1) & 0x7f, \ - ioaddr + REG1); - -/* set diagnose flag */ -#define eepro_diag(ioaddr) outb(DIAGNOSE_CMD, ioaddr) - -/* ack for rx int */ -#define eepro_ack_rx(ioaddr) outb (RX_INT, ioaddr + STATUS_REG) - -/* ack for tx int */ -#define eepro_ack_tx(ioaddr) outb (TX_INT, ioaddr + STATUS_REG) - -/* a complete sel reset */ -#define eepro_complete_selreset(ioaddr) { \ - dev->stats.tx_errors++;\ - eepro_sel_reset(ioaddr);\ - lp->tx_end = \ - lp->xmt_lower_limit;\ - lp->tx_start = lp->tx_end;\ - lp->tx_last = 0;\ - dev->trans_start = jiffies;\ - netif_wake_queue(dev);\ - eepro_en_rx(ioaddr);\ - } - -/* Check for a network adaptor of this type, and return '0' if one exists. - If dev->base_addr == 0, probe all likely locations. - If dev->base_addr == 1, always return failure. - If dev->base_addr == 2, allocate space for the device and return success - (detachable devices only). - */ -static int __init do_eepro_probe(struct net_device *dev) -{ - int i; - int base_addr = dev->base_addr; - int irq = dev->irq; - -#ifdef PnPWakeup - /* XXXX for multiple cards should this only be run once? */ - - /* Wakeup: */ - #define WakeupPort 0x279 - #define WakeupSeq {0x6A, 0xB5, 0xDA, 0xED, 0xF6, 0xFB, 0x7D, 0xBE,\ - 0xDF, 0x6F, 0x37, 0x1B, 0x0D, 0x86, 0xC3, 0x61,\ - 0xB0, 0x58, 0x2C, 0x16, 0x8B, 0x45, 0xA2, 0xD1,\ - 0xE8, 0x74, 0x3A, 0x9D, 0xCE, 0xE7, 0x73, 0x43} - - { - unsigned short int WS[32]=WakeupSeq; - - if (request_region(WakeupPort, 2, "eepro wakeup")) { - if (net_debug>5) - printk(KERN_DEBUG "Waking UP\n"); - - outb_p(0,WakeupPort); - outb_p(0,WakeupPort); - for (i=0; i<32; i++) { - outb_p(WS[i],WakeupPort); - if (net_debug>5) printk(KERN_DEBUG ": %#x ",WS[i]); - } - - release_region(WakeupPort, 2); - } else - printk(KERN_WARNING "PnP wakeup region busy!\n"); - } -#endif - - if (base_addr > 0x1ff) /* Check a single specified location. */ - return eepro_probe1(dev, 0); - - else if (base_addr != 0) /* Don't probe at all. */ - return -ENXIO; - - for (i = 0; eepro_portlist[i]; i++) { - dev->base_addr = eepro_portlist[i]; - dev->irq = irq; - if (eepro_probe1(dev, 1) == 0) - return 0; - } - - return -ENODEV; -} - -#ifndef MODULE -struct net_device * __init eepro_probe(int unit) -{ - struct net_device *dev = alloc_etherdev(sizeof(struct eepro_local)); - int err; - - if (!dev) - return ERR_PTR(-ENODEV); - - sprintf(dev->name, "eth%d", unit); - netdev_boot_setup_check(dev); - - err = do_eepro_probe(dev); - if (err) - goto out; - return dev; -out: - free_netdev(dev); - return ERR_PTR(err); -} -#endif - -static void __init printEEPROMInfo(struct net_device *dev) -{ - struct eepro_local *lp = netdev_priv(dev); - int ioaddr = dev->base_addr; - unsigned short Word; - int i,j; - - j = ee_Checksum; - for (i = 0; i < 8; i++) - j += lp->word[i]; - for ( ; i < ee_SIZE; i++) - j += read_eeprom(ioaddr, i, dev); - - printk(KERN_DEBUG "Checksum: %#x\n",j&0xffff); - - Word = lp->word[0]; - printk(KERN_DEBUG "Word0:\n"); - printk(KERN_DEBUG " Plug 'n Pray: %d\n",GetBit(Word,ee_PnP)); - printk(KERN_DEBUG " Buswidth: %d\n",(GetBit(Word,ee_BusWidth)+1)*8 ); - printk(KERN_DEBUG " AutoNegotiation: %d\n",GetBit(Word,ee_AutoNeg)); - printk(KERN_DEBUG " IO Address: %#x\n", (Word>>ee_IO0)<<4); - - if (net_debug>4) { - Word = lp->word[1]; - printk(KERN_DEBUG "Word1:\n"); - printk(KERN_DEBUG " INT: %d\n", Word & ee_IntMask); - printk(KERN_DEBUG " LI: %d\n", GetBit(Word,ee_LI)); - printk(KERN_DEBUG " PC: %d\n", GetBit(Word,ee_PC)); - printk(KERN_DEBUG " TPE/AUI: %d\n", GetBit(Word,ee_TPE_AUI)); - printk(KERN_DEBUG " Jabber: %d\n", GetBit(Word,ee_Jabber)); - printk(KERN_DEBUG " AutoPort: %d\n", !GetBit(Word,ee_AutoPort)); - printk(KERN_DEBUG " Duplex: %d\n", GetBit(Word,ee_Duplex)); - } - - Word = lp->word[5]; - printk(KERN_DEBUG "Word5:\n"); - printk(KERN_DEBUG " BNC: %d\n",GetBit(Word,ee_BNC_TPE)); - printk(KERN_DEBUG " NumConnectors: %d\n",GetBit(Word,ee_NumConn)); - printk(KERN_DEBUG " Has "); - if (GetBit(Word,ee_PortTPE)) printk(KERN_DEBUG "TPE "); - if (GetBit(Word,ee_PortBNC)) printk(KERN_DEBUG "BNC "); - if (GetBit(Word,ee_PortAUI)) printk(KERN_DEBUG "AUI "); - printk(KERN_DEBUG "port(s)\n"); - - Word = lp->word[6]; - printk(KERN_DEBUG "Word6:\n"); - printk(KERN_DEBUG " Stepping: %d\n",Word & ee_StepMask); - printk(KERN_DEBUG " BoardID: %d\n",Word>>ee_BoardID); - - Word = lp->word[7]; - printk(KERN_DEBUG "Word7:\n"); - printk(KERN_DEBUG " INT to IRQ:\n"); - - for (i=0, j=0; i<15; i++) - if (GetBit(Word,i)) printk(KERN_DEBUG " INT%d -> IRQ %d;",j++,i); - - printk(KERN_DEBUG "\n"); -} - -/* function to recalculate the limits of buffer based on rcv_ram */ -static void eepro_recalc (struct net_device *dev) -{ - struct eepro_local * lp; - - lp = netdev_priv(dev); - lp->xmt_ram = RAM_SIZE - lp->rcv_ram; - - if (lp->eepro == LAN595FX_10ISA) { - lp->xmt_lower_limit = XMT_START_10; - lp->xmt_upper_limit = (lp->xmt_ram - 2); - lp->rcv_lower_limit = lp->xmt_ram; - lp->rcv_upper_limit = (RAM_SIZE - 2); - } - else { - lp->rcv_lower_limit = RCV_START_PRO; - lp->rcv_upper_limit = (lp->rcv_ram - 2); - lp->xmt_lower_limit = lp->rcv_ram; - lp->xmt_upper_limit = (RAM_SIZE - 2); - } -} - -/* prints boot-time info */ -static void __init eepro_print_info (struct net_device *dev) -{ - struct eepro_local * lp = netdev_priv(dev); - int i; - const char * ifmap[] = {"AUI", "10Base2", "10BaseT"}; - - i = inb(dev->base_addr + ID_REG); - printk(KERN_DEBUG " id: %#x ",i); - printk(" io: %#x ", (unsigned)dev->base_addr); - - switch (lp->eepro) { - case LAN595FX_10ISA: - printk("%s: Intel EtherExpress 10 ISA\n at %#x,", - dev->name, (unsigned)dev->base_addr); - break; - case LAN595FX: - printk("%s: Intel EtherExpress Pro/10+ ISA\n at %#x,", - dev->name, (unsigned)dev->base_addr); - break; - case LAN595TX: - printk("%s: Intel EtherExpress Pro/10 ISA at %#x,", - dev->name, (unsigned)dev->base_addr); - break; - case LAN595: - printk("%s: Intel 82595-based lan card at %#x,", - dev->name, (unsigned)dev->base_addr); - break; - } - - printk(" %pM", dev->dev_addr); - - if (net_debug > 3) - printk(KERN_DEBUG ", %dK RCV buffer", - (int)(lp->rcv_ram)/1024); - - if (dev->irq > 2) - printk(", IRQ %d, %s.\n", dev->irq, ifmap[dev->if_port]); - else - printk(", %s.\n", ifmap[dev->if_port]); - - if (net_debug > 3) { - i = lp->word[5]; - if (i & 0x2000) /* bit 13 of EEPROM word 5 */ - printk(KERN_DEBUG "%s: Concurrent Processing is " - "enabled but not used!\n", dev->name); - } - - /* Check the station address for the manufacturer's code */ - if (net_debug>3) - printEEPROMInfo(dev); -} - -static const struct ethtool_ops eepro_ethtool_ops; - -static const struct net_device_ops eepro_netdev_ops = { - .ndo_open = eepro_open, - .ndo_stop = eepro_close, - .ndo_start_xmit = eepro_send_packet, - .ndo_set_rx_mode = set_multicast_list, - .ndo_tx_timeout = eepro_tx_timeout, - .ndo_change_mtu = eth_change_mtu, - .ndo_set_mac_address = eth_mac_addr, - .ndo_validate_addr = eth_validate_addr, -}; - -/* This is the real probe routine. Linux has a history of friendly device - probes on the ISA bus. A good device probe avoids doing writes, and - verifies that the correct device exists and functions. */ - -static int __init eepro_probe1(struct net_device *dev, int autoprobe) -{ - unsigned short station_addr[3], id, counter; - int i; - struct eepro_local *lp; - int ioaddr = dev->base_addr; - int err; - - /* Grab the region so we can find another board if autoIRQ fails. */ - if (!request_region(ioaddr, EEPRO_IO_EXTENT, DRV_NAME)) { - if (!autoprobe) - printk(KERN_WARNING "EEPRO: io-port 0x%04x in use\n", - ioaddr); - return -EBUSY; - } - - /* Now, we are going to check for the signature of the - ID_REG (register 2 of bank 0) */ - - id = inb(ioaddr + ID_REG); - - if ((id & ID_REG_MASK) != ID_REG_SIG) - goto exit; - - /* We seem to have the 82595 signature, let's - play with its counter (last 2 bits of - register 2 of bank 0) to be sure. */ - - counter = id & R_ROBIN_BITS; - - if ((inb(ioaddr + ID_REG) & R_ROBIN_BITS) != (counter + 0x40)) - goto exit; - - lp = netdev_priv(dev); - memset(lp, 0, sizeof(struct eepro_local)); - lp->xmt_bar = XMT_BAR_PRO; - lp->xmt_lower_limit_reg = XMT_LOWER_LIMIT_REG_PRO; - lp->xmt_upper_limit_reg = XMT_UPPER_LIMIT_REG_PRO; - lp->eeprom_reg = EEPROM_REG_PRO; - spin_lock_init(&lp->lock); - - /* Now, get the ethernet hardware address from - the EEPROM */ - station_addr[0] = read_eeprom(ioaddr, 2, dev); - - /* FIXME - find another way to know that we've found - * an Etherexpress 10 - */ - if (station_addr[0] == 0x0000 || station_addr[0] == 0xffff) { - lp->eepro = LAN595FX_10ISA; - lp->eeprom_reg = EEPROM_REG_10; - lp->xmt_lower_limit_reg = XMT_LOWER_LIMIT_REG_10; - lp->xmt_upper_limit_reg = XMT_UPPER_LIMIT_REG_10; - lp->xmt_bar = XMT_BAR_10; - station_addr[0] = read_eeprom(ioaddr, 2, dev); - } - - /* get all words at once. will be used here and for ethtool */ - for (i = 0; i < 8; i++) { - lp->word[i] = read_eeprom(ioaddr, i, dev); - } - station_addr[1] = lp->word[3]; - station_addr[2] = lp->word[4]; - - if (!lp->eepro) { - if (lp->word[7] == ee_FX_INT2IRQ) - lp->eepro = 2; - else if (station_addr[2] == SA_ADDR1) - lp->eepro = 1; - } - - /* Fill in the 'dev' fields. */ - for (i=0; i < 6; i++) - dev->dev_addr[i] = ((unsigned char *) station_addr)[5-i]; - - /* RX buffer must be more than 3K and less than 29K */ - if (dev->mem_end < 3072 || dev->mem_end > 29696) - lp->rcv_ram = RCV_DEFAULT_RAM; - - /* calculate {xmt,rcv}_{lower,upper}_limit */ - eepro_recalc(dev); - - if (GetBit(lp->word[5], ee_BNC_TPE)) - dev->if_port = BNC; - else - dev->if_port = TPE; - - if (dev->irq < 2 && lp->eepro != 0) { - /* Mask off INT number */ - int count = lp->word[1] & 7; - unsigned irqMask = lp->word[7]; - - while (count--) - irqMask &= irqMask - 1; - - count = ffs(irqMask); - - if (count) - dev->irq = count - 1; - - if (dev->irq < 2) { - printk(KERN_ERR " Duh! illegal interrupt vector stored in EEPROM.\n"); - goto exit; - } else if (dev->irq == 2) { - dev->irq = 9; - } - } - - dev->netdev_ops = &eepro_netdev_ops; - dev->watchdog_timeo = TX_TIMEOUT; - dev->ethtool_ops = &eepro_ethtool_ops; - - /* print boot time info */ - eepro_print_info(dev); - - /* reset 82595 */ - eepro_reset(ioaddr); - - err = register_netdev(dev); - if (err) - goto err; - return 0; -exit: - err = -ENODEV; -err: - release_region(dev->base_addr, EEPRO_IO_EXTENT); - return err; -} - -/* Open/initialize the board. This is called (in the current kernel) - sometime after booting when the 'ifconfig' program is run. - - This routine should set everything up anew at each open, even - registers that "should" only need to be set once at boot, so that - there is non-reboot way to recover if something goes wrong. - */ - -static const char irqrmap[] = {-1,-1,0,1,-1,2,-1,-1,-1,0,3,4,-1,-1,-1,-1}; -static const char irqrmap2[] = {-1,-1,4,0,1,2,-1,3,-1,4,5,6,7,-1,-1,-1}; -static int eepro_grab_irq(struct net_device *dev) -{ - static const int irqlist[] = { 3, 4, 5, 7, 9, 10, 11, 12, 0 }; - const int *irqp = irqlist; - int temp_reg, ioaddr = dev->base_addr; - - eepro_sw2bank1(ioaddr); /* be CAREFUL, BANK 1 now */ - - /* Enable the interrupt line. */ - eepro_en_intline(ioaddr); - - /* be CAREFUL, BANK 0 now */ - eepro_sw2bank0(ioaddr); - - /* clear all interrupts */ - eepro_clear_int(ioaddr); - - /* Let EXEC event to interrupt */ - eepro_en_intexec(ioaddr); - - do { - eepro_sw2bank1(ioaddr); /* be CAREFUL, BANK 1 now */ - - temp_reg = inb(ioaddr + INT_NO_REG); - outb((temp_reg & 0xf8) | irqrmap[*irqp], ioaddr + INT_NO_REG); - - eepro_sw2bank0(ioaddr); /* Switch back to Bank 0 */ - - if (request_irq (*irqp, NULL, IRQF_SHARED, "bogus", dev) != EBUSY) { - unsigned long irq_mask; - /* Twinkle the interrupt, and check if it's seen */ - irq_mask = probe_irq_on(); - - eepro_diag(ioaddr); /* RESET the 82595 */ - mdelay(20); - - if (*irqp == probe_irq_off(irq_mask)) /* It's a good IRQ line */ - break; - - /* clear all interrupts */ - eepro_clear_int(ioaddr); - } - } while (*++irqp); - - eepro_sw2bank1(ioaddr); /* Switch back to Bank 1 */ - - /* Disable the physical interrupt line. */ - eepro_dis_intline(ioaddr); - - eepro_sw2bank0(ioaddr); /* Switch back to Bank 0 */ - - /* Mask all the interrupts. */ - eepro_dis_int(ioaddr); - - /* clear all interrupts */ - eepro_clear_int(ioaddr); - - return dev->irq; -} - -static int eepro_open(struct net_device *dev) -{ - unsigned short temp_reg, old8, old9; - int irqMask; - int i, ioaddr = dev->base_addr; - struct eepro_local *lp = netdev_priv(dev); - - if (net_debug > 3) - printk(KERN_DEBUG "%s: entering eepro_open routine.\n", dev->name); - - irqMask = lp->word[7]; - - if (lp->eepro == LAN595FX_10ISA) { - if (net_debug > 3) printk(KERN_DEBUG "p->eepro = 3;\n"); - } - else if (irqMask == ee_FX_INT2IRQ) /* INT to IRQ Mask */ - { - lp->eepro = 2; /* Yes, an Intel EtherExpress Pro/10+ */ - if (net_debug > 3) printk(KERN_DEBUG "p->eepro = 2;\n"); - } - - else if ((dev->dev_addr[0] == SA_ADDR0 && - dev->dev_addr[1] == SA_ADDR1 && - dev->dev_addr[2] == SA_ADDR2)) - { - lp->eepro = 1; - if (net_debug > 3) printk(KERN_DEBUG "p->eepro = 1;\n"); - } /* Yes, an Intel EtherExpress Pro/10 */ - - else lp->eepro = 0; /* No, it is a generic 82585 lan card */ - - /* Get the interrupt vector for the 82595 */ - if (dev->irq < 2 && eepro_grab_irq(dev) == 0) { - printk(KERN_ERR "%s: unable to get IRQ %d.\n", dev->name, dev->irq); - return -EAGAIN; - } - - if (request_irq(dev->irq , eepro_interrupt, 0, dev->name, dev)) { - printk(KERN_ERR "%s: unable to get IRQ %d.\n", dev->name, dev->irq); - return -EAGAIN; - } - - /* Initialize the 82595. */ - - eepro_sw2bank2(ioaddr); /* be CAREFUL, BANK 2 now */ - temp_reg = inb(ioaddr + lp->eeprom_reg); - - lp->stepping = temp_reg >> 5; /* Get the stepping number of the 595 */ - - if (net_debug > 3) - printk(KERN_DEBUG "The stepping of the 82595 is %d\n", lp->stepping); - - if (temp_reg & 0x10) /* Check the TurnOff Enable bit */ - outb(temp_reg & 0xef, ioaddr + lp->eeprom_reg); - for (i=0; i < 6; i++) - outb(dev->dev_addr[i] , ioaddr + I_ADD_REG0 + i); - - temp_reg = inb(ioaddr + REG1); /* Setup Transmit Chaining */ - outb(temp_reg | XMT_Chain_Int | XMT_Chain_ErrStop /* and discard bad RCV frames */ - | RCV_Discard_BadFrame, ioaddr + REG1); - - temp_reg = inb(ioaddr + REG2); /* Match broadcast */ - outb(temp_reg | 0x14, ioaddr + REG2); - - temp_reg = inb(ioaddr + REG3); - outb(temp_reg & 0x3f, ioaddr + REG3); /* clear test mode */ - - /* Set the receiving mode */ - eepro_sw2bank1(ioaddr); /* be CAREFUL, BANK 1 now */ - - /* Set the interrupt vector */ - temp_reg = inb(ioaddr + INT_NO_REG); - if (lp->eepro == LAN595FX || lp->eepro == LAN595FX_10ISA) - outb((temp_reg & 0xf8) | irqrmap2[dev->irq], ioaddr + INT_NO_REG); - else outb((temp_reg & 0xf8) | irqrmap[dev->irq], ioaddr + INT_NO_REG); - - - temp_reg = inb(ioaddr + INT_NO_REG); - if (lp->eepro == LAN595FX || lp->eepro == LAN595FX_10ISA) - outb((temp_reg & 0xf0) | irqrmap2[dev->irq] | 0x08,ioaddr+INT_NO_REG); - else outb((temp_reg & 0xf8) | irqrmap[dev->irq], ioaddr + INT_NO_REG); - - if (net_debug > 3) - printk(KERN_DEBUG "eepro_open: content of INT Reg is %x\n", temp_reg); - - - /* Initialize the RCV and XMT upper and lower limits */ - outb(lp->rcv_lower_limit >> 8, ioaddr + RCV_LOWER_LIMIT_REG); - outb(lp->rcv_upper_limit >> 8, ioaddr + RCV_UPPER_LIMIT_REG); - outb(lp->xmt_lower_limit >> 8, ioaddr + lp->xmt_lower_limit_reg); - outb(lp->xmt_upper_limit >> 8, ioaddr + lp->xmt_upper_limit_reg); - - /* Enable the interrupt line. */ - eepro_en_intline(ioaddr); - - /* Switch back to Bank 0 */ - eepro_sw2bank0(ioaddr); - - /* Let RX and TX events to interrupt */ - eepro_en_int(ioaddr); - - /* clear all interrupts */ - eepro_clear_int(ioaddr); - - /* Initialize RCV */ - outw(lp->rcv_lower_limit, ioaddr + RCV_BAR); - lp->rx_start = lp->rcv_lower_limit; - outw(lp->rcv_upper_limit | 0xfe, ioaddr + RCV_STOP); - - /* Initialize XMT */ - outw(lp->xmt_lower_limit, ioaddr + lp->xmt_bar); - lp->tx_start = lp->tx_end = lp->xmt_lower_limit; - lp->tx_last = 0; - - /* Check for the i82595TX and i82595FX */ - old8 = inb(ioaddr + 8); - outb(~old8, ioaddr + 8); - - if ((temp_reg = inb(ioaddr + 8)) == old8) { - if (net_debug > 3) - printk(KERN_DEBUG "i82595 detected!\n"); - lp->version = LAN595; - } - else { - lp->version = LAN595TX; - outb(old8, ioaddr + 8); - old9 = inb(ioaddr + 9); - - if (irqMask==ee_FX_INT2IRQ) { - if (net_debug > 3) { - printk(KERN_DEBUG "IrqMask: %#x\n",irqMask); - printk(KERN_DEBUG "i82595FX detected!\n"); - } - lp->version = LAN595FX; - outb(old9, ioaddr + 9); - if (dev->if_port != TPE) { /* Hopefully, this will fix the - problem of using Pentiums and - pro/10 w/ BNC. */ - eepro_sw2bank2(ioaddr); /* be CAREFUL, BANK 2 now */ - temp_reg = inb(ioaddr + REG13); - /* disable the full duplex mode since it is not - applicable with the 10Base2 cable. */ - outb(temp_reg & ~(FDX | A_N_ENABLE), REG13); - eepro_sw2bank0(ioaddr); /* be CAREFUL, BANK 0 now */ - } - } - else if (net_debug > 3) { - printk(KERN_DEBUG "temp_reg: %#x ~old9: %#x\n",temp_reg,((~old9)&0xff)); - printk(KERN_DEBUG "i82595TX detected!\n"); - } - } - - eepro_sel_reset(ioaddr); - - netif_start_queue(dev); - - if (net_debug > 3) - printk(KERN_DEBUG "%s: exiting eepro_open routine.\n", dev->name); - - /* enabling rx */ - eepro_en_rx(ioaddr); - - return 0; -} - -static void eepro_tx_timeout (struct net_device *dev) -{ - struct eepro_local *lp = netdev_priv(dev); - int ioaddr = dev->base_addr; - - /* if (net_debug > 1) */ - printk (KERN_ERR "%s: transmit timed out, %s?\n", dev->name, - "network cable problem"); - /* This is not a duplicate. One message for the console, - one for the log file */ - printk (KERN_DEBUG "%s: transmit timed out, %s?\n", dev->name, - "network cable problem"); - eepro_complete_selreset(ioaddr); -} - - -static netdev_tx_t eepro_send_packet(struct sk_buff *skb, - struct net_device *dev) -{ - struct eepro_local *lp = netdev_priv(dev); - unsigned long flags; - int ioaddr = dev->base_addr; - short length = skb->len; - - if (net_debug > 5) - printk(KERN_DEBUG "%s: entering eepro_send_packet routine.\n", dev->name); - - if (length < ETH_ZLEN) { - if (skb_padto(skb, ETH_ZLEN)) - return NETDEV_TX_OK; - length = ETH_ZLEN; - } - netif_stop_queue (dev); - - eepro_dis_int(ioaddr); - spin_lock_irqsave(&lp->lock, flags); - - { - unsigned char *buf = skb->data; - - if (hardware_send_packet(dev, buf, length)) - /* we won't wake queue here because we're out of space */ - dev->stats.tx_dropped++; - else { - dev->stats.tx_bytes+=skb->len; - netif_wake_queue(dev); - } - - } - - dev_kfree_skb (skb); - - /* You might need to clean up and record Tx statistics here. */ - /* dev->stats.tx_aborted_errors++; */ - - if (net_debug > 5) - printk(KERN_DEBUG "%s: exiting eepro_send_packet routine.\n", dev->name); - - eepro_en_int(ioaddr); - spin_unlock_irqrestore(&lp->lock, flags); - - return NETDEV_TX_OK; -} - - -/* The typical workload of the driver: - Handle the network interface interrupts. */ - -static irqreturn_t -eepro_interrupt(int irq, void *dev_id) -{ - struct net_device *dev = dev_id; - struct eepro_local *lp; - int ioaddr, status, boguscount = 20; - int handled = 0; - - lp = netdev_priv(dev); - - spin_lock(&lp->lock); - - if (net_debug > 5) - printk(KERN_DEBUG "%s: entering eepro_interrupt routine.\n", dev->name); - - ioaddr = dev->base_addr; - - while (((status = inb(ioaddr + STATUS_REG)) & (RX_INT|TX_INT)) && (boguscount--)) - { - handled = 1; - if (status & RX_INT) { - if (net_debug > 4) - printk(KERN_DEBUG "%s: packet received interrupt.\n", dev->name); - - eepro_dis_int(ioaddr); - - /* Get the received packets */ - eepro_ack_rx(ioaddr); - eepro_rx(dev); - - eepro_en_int(ioaddr); - } - if (status & TX_INT) { - if (net_debug > 4) - printk(KERN_DEBUG "%s: packet transmit interrupt.\n", dev->name); - - - eepro_dis_int(ioaddr); - - /* Process the status of transmitted packets */ - eepro_ack_tx(ioaddr); - eepro_transmit_interrupt(dev); - - eepro_en_int(ioaddr); - } - } - - if (net_debug > 5) - printk(KERN_DEBUG "%s: exiting eepro_interrupt routine.\n", dev->name); - - spin_unlock(&lp->lock); - return IRQ_RETVAL(handled); -} - -static int eepro_close(struct net_device *dev) -{ - struct eepro_local *lp = netdev_priv(dev); - int ioaddr = dev->base_addr; - short temp_reg; - - netif_stop_queue(dev); - - eepro_sw2bank1(ioaddr); /* Switch back to Bank 1 */ - - /* Disable the physical interrupt line. */ - temp_reg = inb(ioaddr + REG1); - outb(temp_reg & 0x7f, ioaddr + REG1); - - eepro_sw2bank0(ioaddr); /* Switch back to Bank 0 */ - - /* Flush the Tx and disable Rx. */ - outb(STOP_RCV_CMD, ioaddr); - lp->tx_start = lp->tx_end = lp->xmt_lower_limit; - lp->tx_last = 0; - - /* Mask all the interrupts. */ - eepro_dis_int(ioaddr); - - /* clear all interrupts */ - eepro_clear_int(ioaddr); - - /* Reset the 82595 */ - eepro_reset(ioaddr); - - /* release the interrupt */ - free_irq(dev->irq, dev); - - /* Update the statistics here. What statistics? */ - - return 0; -} - -/* Set or clear the multicast filter for this adaptor. - */ -static void -set_multicast_list(struct net_device *dev) -{ - struct eepro_local *lp = netdev_priv(dev); - short ioaddr = dev->base_addr; - unsigned short mode; - struct netdev_hw_addr *ha; - int mc_count = netdev_mc_count(dev); - - if (dev->flags&(IFF_ALLMULTI|IFF_PROMISC) || mc_count > 63) - { - eepro_sw2bank2(ioaddr); /* be CAREFUL, BANK 2 now */ - mode = inb(ioaddr + REG2); - outb(mode | PRMSC_Mode, ioaddr + REG2); - mode = inb(ioaddr + REG3); - outb(mode, ioaddr + REG3); /* writing reg. 3 to complete the update */ - eepro_sw2bank0(ioaddr); /* Return to BANK 0 now */ - } - - else if (mc_count == 0) - { - eepro_sw2bank2(ioaddr); /* be CAREFUL, BANK 2 now */ - mode = inb(ioaddr + REG2); - outb(mode & 0xd6, ioaddr + REG2); /* Turn off Multi-IA and PRMSC_Mode bits */ - mode = inb(ioaddr + REG3); - outb(mode, ioaddr + REG3); /* writing reg. 3 to complete the update */ - eepro_sw2bank0(ioaddr); /* Return to BANK 0 now */ - } - - else - { - unsigned short status, *eaddrs; - int i, boguscount = 0; - - /* Disable RX and TX interrupts. Necessary to avoid - corruption of the HOST_ADDRESS_REG by interrupt - service routines. */ - eepro_dis_int(ioaddr); - - eepro_sw2bank2(ioaddr); /* be CAREFUL, BANK 2 now */ - mode = inb(ioaddr + REG2); - outb(mode | Multi_IA, ioaddr + REG2); - mode = inb(ioaddr + REG3); - outb(mode, ioaddr + REG3); /* writing reg. 3 to complete the update */ - eepro_sw2bank0(ioaddr); /* Return to BANK 0 now */ - outw(lp->tx_end, ioaddr + HOST_ADDRESS_REG); - outw(MC_SETUP, ioaddr + IO_PORT); - outw(0, ioaddr + IO_PORT); - outw(0, ioaddr + IO_PORT); - outw(6 * (mc_count + 1), ioaddr + IO_PORT); - - netdev_for_each_mc_addr(ha, dev) { - eaddrs = (unsigned short *) ha->addr; - outw(*eaddrs++, ioaddr + IO_PORT); - outw(*eaddrs++, ioaddr + IO_PORT); - outw(*eaddrs++, ioaddr + IO_PORT); - } - - eaddrs = (unsigned short *) dev->dev_addr; - outw(eaddrs[0], ioaddr + IO_PORT); - outw(eaddrs[1], ioaddr + IO_PORT); - outw(eaddrs[2], ioaddr + IO_PORT); - outw(lp->tx_end, ioaddr + lp->xmt_bar); - outb(MC_SETUP, ioaddr); - - /* Update the transmit queue */ - i = lp->tx_end + XMT_HEADER + 6 * (mc_count + 1); - - if (lp->tx_start != lp->tx_end) - { - /* update the next address and the chain bit in the - last packet */ - outw(lp->tx_last + XMT_CHAIN, ioaddr + HOST_ADDRESS_REG); - outw(i, ioaddr + IO_PORT); - outw(lp->tx_last + XMT_COUNT, ioaddr + HOST_ADDRESS_REG); - status = inw(ioaddr + IO_PORT); - outw(status | CHAIN_BIT, ioaddr + IO_PORT); - lp->tx_end = i ; - } - else { - lp->tx_start = lp->tx_end = i ; - } - - /* Acknowledge that the MC setup is done */ - do { /* We should be doing this in the eepro_interrupt()! */ - SLOW_DOWN; - SLOW_DOWN; - if (inb(ioaddr + STATUS_REG) & 0x08) - { - i = inb(ioaddr); - outb(0x08, ioaddr + STATUS_REG); - - if (i & 0x20) { /* command ABORTed */ - printk(KERN_NOTICE "%s: multicast setup failed.\n", - dev->name); - break; - } else if ((i & 0x0f) == 0x03) { /* MC-Done */ - printk(KERN_DEBUG "%s: set Rx mode to %d address%s.\n", - dev->name, mc_count, - mc_count > 1 ? "es":""); - break; - } - } - } while (++boguscount < 100); - - /* Re-enable RX and TX interrupts */ - eepro_en_int(ioaddr); - } - if (lp->eepro == LAN595FX_10ISA) { - eepro_complete_selreset(ioaddr); - } - else - eepro_en_rx(ioaddr); -} - -/* The horrible routine to read a word from the serial EEPROM. */ -/* IMPORTANT - the 82595 will be set to Bank 0 after the eeprom is read */ - -/* The delay between EEPROM clock transitions. */ -#define eeprom_delay() { udelay(40); } -#define EE_READ_CMD (6 << 6) - -static int -read_eeprom(int ioaddr, int location, struct net_device *dev) -{ - int i; - unsigned short retval = 0; - struct eepro_local *lp = netdev_priv(dev); - short ee_addr = ioaddr + lp->eeprom_reg; - int read_cmd = location | EE_READ_CMD; - short ctrl_val = EECS ; - - /* XXXX - black magic */ - eepro_sw2bank1(ioaddr); - outb(0x00, ioaddr + STATUS_REG); - /* XXXX - black magic */ - - eepro_sw2bank2(ioaddr); - outb(ctrl_val, ee_addr); - - /* Shift the read command bits out. */ - for (i = 8; i >= 0; i--) { - short outval = (read_cmd & (1 << i)) ? ctrl_val | EEDI - : ctrl_val; - outb(outval, ee_addr); - outb(outval | EESK, ee_addr); /* EEPROM clock tick. */ - eeprom_delay(); - outb(outval, ee_addr); /* Finish EEPROM a clock tick. */ - eeprom_delay(); - } - outb(ctrl_val, ee_addr); - - for (i = 16; i > 0; i--) { - outb(ctrl_val | EESK, ee_addr); eeprom_delay(); - retval = (retval << 1) | ((inb(ee_addr) & EEDO) ? 1 : 0); - outb(ctrl_val, ee_addr); eeprom_delay(); - } - - /* Terminate the EEPROM access. */ - ctrl_val &= ~EECS; - outb(ctrl_val | EESK, ee_addr); - eeprom_delay(); - outb(ctrl_val, ee_addr); - eeprom_delay(); - eepro_sw2bank0(ioaddr); - return retval; -} - -static int -hardware_send_packet(struct net_device *dev, void *buf, short length) -{ - struct eepro_local *lp = netdev_priv(dev); - short ioaddr = dev->base_addr; - unsigned status, tx_available, last, end; - - if (net_debug > 5) - printk(KERN_DEBUG "%s: entering hardware_send_packet routine.\n", dev->name); - - /* determine how much of the transmit buffer space is available */ - if (lp->tx_end > lp->tx_start) - tx_available = lp->xmt_ram - (lp->tx_end - lp->tx_start); - else if (lp->tx_end < lp->tx_start) - tx_available = lp->tx_start - lp->tx_end; - else tx_available = lp->xmt_ram; - - if (((((length + 3) >> 1) << 1) + 2*XMT_HEADER) >= tx_available) { - /* No space available ??? */ - return 1; - } - - last = lp->tx_end; - end = last + (((length + 3) >> 1) << 1) + XMT_HEADER; - - if (end >= lp->xmt_upper_limit + 2) { /* the transmit buffer is wrapped around */ - if ((lp->xmt_upper_limit + 2 - last) <= XMT_HEADER) { - /* Arrrr!!!, must keep the xmt header together, - several days were lost to chase this one down. */ - last = lp->xmt_lower_limit; - end = last + (((length + 3) >> 1) << 1) + XMT_HEADER; - } - else end = lp->xmt_lower_limit + (end - - lp->xmt_upper_limit + 2); - } - - outw(last, ioaddr + HOST_ADDRESS_REG); - outw(XMT_CMD, ioaddr + IO_PORT); - outw(0, ioaddr + IO_PORT); - outw(end, ioaddr + IO_PORT); - outw(length, ioaddr + IO_PORT); - - if (lp->version == LAN595) - outsw(ioaddr + IO_PORT, buf, (length + 3) >> 1); - else { /* LAN595TX or LAN595FX, capable of 32-bit I/O processing */ - unsigned short temp = inb(ioaddr + INT_MASK_REG); - outb(temp | IO_32_BIT, ioaddr + INT_MASK_REG); - outsl(ioaddr + IO_PORT_32_BIT, buf, (length + 3) >> 2); - outb(temp & ~(IO_32_BIT), ioaddr + INT_MASK_REG); - } - - /* A dummy read to flush the DRAM write pipeline */ - status = inw(ioaddr + IO_PORT); - - if (lp->tx_start == lp->tx_end) { - outw(last, ioaddr + lp->xmt_bar); - outb(XMT_CMD, ioaddr); - lp->tx_start = last; /* I don't like to change tx_start here */ - } - else { - /* update the next address and the chain bit in the - last packet */ - - if (lp->tx_end != last) { - outw(lp->tx_last + XMT_CHAIN, ioaddr + HOST_ADDRESS_REG); - outw(last, ioaddr + IO_PORT); - } - - outw(lp->tx_last + XMT_COUNT, ioaddr + HOST_ADDRESS_REG); - status = inw(ioaddr + IO_PORT); - outw(status | CHAIN_BIT, ioaddr + IO_PORT); - - /* Continue the transmit command */ - outb(RESUME_XMT_CMD, ioaddr); - } - - lp->tx_last = last; - lp->tx_end = end; - - if (net_debug > 5) - printk(KERN_DEBUG "%s: exiting hardware_send_packet routine.\n", dev->name); - - return 0; -} - -static void -eepro_rx(struct net_device *dev) -{ - struct eepro_local *lp = netdev_priv(dev); - short ioaddr = dev->base_addr; - short boguscount = 20; - short rcv_car = lp->rx_start; - unsigned rcv_event, rcv_status, rcv_next_frame, rcv_size; - - if (net_debug > 5) - printk(KERN_DEBUG "%s: entering eepro_rx routine.\n", dev->name); - - /* Set the read pointer to the start of the RCV */ - outw(rcv_car, ioaddr + HOST_ADDRESS_REG); - - rcv_event = inw(ioaddr + IO_PORT); - - while (rcv_event == RCV_DONE) { - - rcv_status = inw(ioaddr + IO_PORT); - rcv_next_frame = inw(ioaddr + IO_PORT); - rcv_size = inw(ioaddr + IO_PORT); - - if ((rcv_status & (RX_OK | RX_ERROR)) == RX_OK) { - - /* Malloc up new buffer. */ - struct sk_buff *skb; - - dev->stats.rx_bytes+=rcv_size; - rcv_size &= 0x3fff; - skb = netdev_alloc_skb(dev, rcv_size + 5); - if (skb == NULL) { - printk(KERN_NOTICE "%s: Memory squeeze, dropping packet.\n", dev->name); - dev->stats.rx_dropped++; - rcv_car = lp->rx_start + RCV_HEADER + rcv_size; - lp->rx_start = rcv_next_frame; - outw(rcv_next_frame, ioaddr + HOST_ADDRESS_REG); - - break; - } - skb_reserve(skb,2); - - if (lp->version == LAN595) - insw(ioaddr+IO_PORT, skb_put(skb,rcv_size), (rcv_size + 3) >> 1); - else { /* LAN595TX or LAN595FX, capable of 32-bit I/O processing */ - unsigned short temp = inb(ioaddr + INT_MASK_REG); - outb(temp | IO_32_BIT, ioaddr + INT_MASK_REG); - insl(ioaddr+IO_PORT_32_BIT, skb_put(skb,rcv_size), - (rcv_size + 3) >> 2); - outb(temp & ~(IO_32_BIT), ioaddr + INT_MASK_REG); - } - - skb->protocol = eth_type_trans(skb,dev); - netif_rx(skb); - dev->stats.rx_packets++; - } - - else { /* Not sure will ever reach here, - I set the 595 to discard bad received frames */ - dev->stats.rx_errors++; - - if (rcv_status & 0x0100) - dev->stats.rx_over_errors++; - - else if (rcv_status & 0x0400) - dev->stats.rx_frame_errors++; - - else if (rcv_status & 0x0800) - dev->stats.rx_crc_errors++; - - printk(KERN_DEBUG "%s: event = %#x, status = %#x, next = %#x, size = %#x\n", - dev->name, rcv_event, rcv_status, rcv_next_frame, rcv_size); - } - - if (rcv_status & 0x1000) - dev->stats.rx_length_errors++; - - rcv_car = lp->rx_start + RCV_HEADER + rcv_size; - lp->rx_start = rcv_next_frame; - - if (--boguscount == 0) - break; - - outw(rcv_next_frame, ioaddr + HOST_ADDRESS_REG); - rcv_event = inw(ioaddr + IO_PORT); - - } - if (rcv_car == 0) - rcv_car = lp->rcv_upper_limit | 0xff; - - outw(rcv_car - 1, ioaddr + RCV_STOP); - - if (net_debug > 5) - printk(KERN_DEBUG "%s: exiting eepro_rx routine.\n", dev->name); -} - -static void -eepro_transmit_interrupt(struct net_device *dev) -{ - struct eepro_local *lp = netdev_priv(dev); - short ioaddr = dev->base_addr; - short boguscount = 25; - short xmt_status; - - while ((lp->tx_start != lp->tx_end) && boguscount--) { - - outw(lp->tx_start, ioaddr + HOST_ADDRESS_REG); - xmt_status = inw(ioaddr+IO_PORT); - - if (!(xmt_status & TX_DONE_BIT)) - break; - - xmt_status = inw(ioaddr+IO_PORT); - lp->tx_start = inw(ioaddr+IO_PORT); - - netif_wake_queue (dev); - - if (xmt_status & TX_OK) - dev->stats.tx_packets++; - else { - dev->stats.tx_errors++; - if (xmt_status & 0x0400) { - dev->stats.tx_carrier_errors++; - printk(KERN_DEBUG "%s: carrier error\n", - dev->name); - printk(KERN_DEBUG "%s: XMT status = %#x\n", - dev->name, xmt_status); - } - else { - printk(KERN_DEBUG "%s: XMT status = %#x\n", - dev->name, xmt_status); - printk(KERN_DEBUG "%s: XMT status = %#x\n", - dev->name, xmt_status); - } - } - if (xmt_status & 0x000f) { - dev->stats.collisions += (xmt_status & 0x000f); - } - - if ((xmt_status & 0x0040) == 0x0) { - dev->stats.tx_heartbeat_errors++; - } - } -} - -static int eepro_ethtool_get_settings(struct net_device *dev, - struct ethtool_cmd *cmd) -{ - struct eepro_local *lp = netdev_priv(dev); - - cmd->supported = SUPPORTED_10baseT_Half | - SUPPORTED_10baseT_Full | - SUPPORTED_Autoneg; - cmd->advertising = ADVERTISED_10baseT_Half | - ADVERTISED_10baseT_Full | - ADVERTISED_Autoneg; - - if (GetBit(lp->word[5], ee_PortTPE)) { - cmd->supported |= SUPPORTED_TP; - cmd->advertising |= ADVERTISED_TP; - } - if (GetBit(lp->word[5], ee_PortBNC)) { - cmd->supported |= SUPPORTED_BNC; - cmd->advertising |= ADVERTISED_BNC; - } - if (GetBit(lp->word[5], ee_PortAUI)) { - cmd->supported |= SUPPORTED_AUI; - cmd->advertising |= ADVERTISED_AUI; - } - - ethtool_cmd_speed_set(cmd, SPEED_10); - - if (dev->if_port == TPE && lp->word[1] & ee_Duplex) { - cmd->duplex = DUPLEX_FULL; - } - else { - cmd->duplex = DUPLEX_HALF; - } - - cmd->port = dev->if_port; - cmd->phy_address = dev->base_addr; - cmd->transceiver = XCVR_INTERNAL; - - if (lp->word[0] & ee_AutoNeg) { - cmd->autoneg = 1; - } - - return 0; -} - -static void eepro_ethtool_get_drvinfo(struct net_device *dev, - struct ethtool_drvinfo *drvinfo) -{ - strlcpy(drvinfo->driver, DRV_NAME, sizeof(drvinfo->driver)); - strlcpy(drvinfo->version, DRV_VERSION, sizeof(drvinfo->version)); - snprintf(drvinfo->bus_info, sizeof(drvinfo->bus_info), - "ISA 0x%lx", dev->base_addr); -} - -static const struct ethtool_ops eepro_ethtool_ops = { - .get_settings = eepro_ethtool_get_settings, - .get_drvinfo = eepro_ethtool_get_drvinfo, -}; - -#ifdef MODULE - -#define MAX_EEPRO 8 -static struct net_device *dev_eepro[MAX_EEPRO]; - -static int io[MAX_EEPRO] = { - [0 ... MAX_EEPRO-1] = -1 -}; -static int irq[MAX_EEPRO]; -static int mem[MAX_EEPRO] = { /* Size of the rx buffer in KB */ - [0 ... MAX_EEPRO-1] = RCV_DEFAULT_RAM/1024 -}; -static int autodetect; - -static int n_eepro; -/* For linux 2.1.xx */ - -MODULE_AUTHOR("Pascal Dupuis and others"); -MODULE_DESCRIPTION("Intel i82595 ISA EtherExpressPro10/10+ driver"); -MODULE_LICENSE("GPL"); - -module_param_array(io, int, NULL, 0); -module_param_array(irq, int, NULL, 0); -module_param_array(mem, int, NULL, 0); -module_param(autodetect, int, 0); -MODULE_PARM_DESC(io, "EtherExpress Pro/10 I/O base address(es)"); -MODULE_PARM_DESC(irq, "EtherExpress Pro/10 IRQ number(s)"); -MODULE_PARM_DESC(mem, "EtherExpress Pro/10 Rx buffer size(es) in kB (3-29)"); -MODULE_PARM_DESC(autodetect, "EtherExpress Pro/10 force board(s) detection (0-1)"); - -int __init init_module(void) -{ - struct net_device *dev; - int i; - if (io[0] == -1 && autodetect == 0) { - printk(KERN_WARNING "eepro_init_module: Probe is very dangerous in ISA boards!\n"); - printk(KERN_WARNING "eepro_init_module: Please add \"autodetect=1\" to force probe\n"); - return -ENODEV; - } - else if (autodetect) { - /* if autodetect is set then we must force detection */ - for (i = 0; i < MAX_EEPRO; i++) { - io[i] = 0; - } - - printk(KERN_INFO "eepro_init_module: Auto-detecting boards (May God protect us...)\n"); - } - - for (i = 0; i < MAX_EEPRO && io[i] != -1; i++) { - dev = alloc_etherdev(sizeof(struct eepro_local)); - if (!dev) - break; - - dev->mem_end = mem[i]; - dev->base_addr = io[i]; - dev->irq = irq[i]; - - if (do_eepro_probe(dev) == 0) { - dev_eepro[n_eepro++] = dev; - continue; - } - free_netdev(dev); - break; - } - - if (n_eepro) - printk(KERN_INFO "%s", version); - - return n_eepro ? 0 : -ENODEV; -} - -void __exit -cleanup_module(void) -{ - int i; - - for (i=0; i<n_eepro; i++) { - struct net_device *dev = dev_eepro[i]; - unregister_netdev(dev); - release_region(dev->base_addr, EEPRO_IO_EXTENT); - free_netdev(dev); - } -} -#endif /* MODULE */ diff --git a/drivers/net/ethernet/i825xx/eexpress.c b/drivers/net/ethernet/i825xx/eexpress.c deleted file mode 100644 index 7a6a2f04c5b1..000000000000 --- a/drivers/net/ethernet/i825xx/eexpress.c +++ /dev/null @@ -1,1661 +0,0 @@ -/* Intel EtherExpress 16 device driver for Linux - * - * Written by John Sullivan, 1995 - * based on original code by Donald Becker, with changes by - * Alan Cox and Pauline Middelink. - * - * Support for 8-bit mode by Zoltan Szilagyi <zoltans@cs.arizona.edu> - * - * Many modifications, and currently maintained, by - * Philip Blundell <philb@gnu.org> - * Added the Compaq LTE Alan Cox <alan@lxorguk.ukuu.org.uk> - * Added MCA support Adam Fritzler (now deleted) - * - * Note - this driver is experimental still - it has problems on faster - * machines. Someone needs to sit down and go through it line by line with - * a databook... - */ - -/* The EtherExpress 16 is a fairly simple card, based on a shared-memory - * design using the i82586 Ethernet coprocessor. It bears no relationship, - * as far as I know, to the similarly-named "EtherExpress Pro" range. - * - * Historically, Linux support for these cards has been very bad. However, - * things seem to be getting better slowly. - */ - -/* If your card is confused about what sort of interface it has (eg it - * persistently reports "10baseT" when none is fitted), running 'SOFTSET /BART' - * or 'SOFTSET /LISA' from DOS seems to help. - */ - -/* Here's the scoop on memory mapping. - * - * There are three ways to access EtherExpress card memory: either using the - * shared-memory mapping, or using PIO through the dataport, or using PIO - * through the "shadow memory" ports. - * - * The shadow memory system works by having the card map some of its memory - * as follows: - * - * (the low five bits of the SMPTR are ignored) - * - * base+0x4000..400f memory at SMPTR+0..15 - * base+0x8000..800f memory at SMPTR+16..31 - * base+0xc000..c007 dubious stuff (memory at SMPTR+16..23 apparently) - * base+0xc008..c00f memory at 0x0008..0x000f - * - * This last set (the one at c008) is particularly handy because the SCB - * lives at 0x0008. So that set of ports gives us easy random access to data - * in the SCB without having to mess around setting up pointers and the like. - * We always use this method to access the SCB (via the scb_xx() functions). - * - * Dataport access works by aiming the appropriate (read or write) pointer - * at the first address you're interested in, and then reading or writing from - * the dataport. The pointers auto-increment after each transfer. We use - * this for data transfer. - * - * We don't use the shared-memory system because it allegedly doesn't work on - * all cards, and because it's a bit more prone to go wrong (it's one more - * thing to configure...). - */ - -/* Known bugs: - * - * - The card seems to want to give us two interrupts every time something - * happens, where just one would be better. - */ - -/* - * - * Note by Zoltan Szilagyi 10-12-96: - * - * I've succeeded in eliminating the "CU wedged" messages, and hence the - * lockups, which were only occurring with cards running in 8-bit mode ("force - * 8-bit operation" in Intel's SoftSet utility). This version of the driver - * sets the 82586 and the ASIC to 8-bit mode at startup; it also stops the - * CU before submitting a packet for transmission, and then restarts it as soon - * as the process of handing the packet is complete. This is definitely an - * unnecessary slowdown if the card is running in 16-bit mode; therefore one - * should detect 16-bit vs 8-bit mode from the EEPROM settings and act - * accordingly. In 8-bit mode with this bugfix I'm getting about 150 K/s for - * ftp's, which is significantly better than I get in DOS, so the overhead of - * stopping and restarting the CU with each transmit is not prohibitive in - * practice. - * - * Update by David Woodhouse 11/5/99: - * - * I've seen "CU wedged" messages in 16-bit mode, on the Alpha architecture. - * I assume that this is because 16-bit accesses are actually handled as two - * 8-bit accesses. - */ - -#ifdef __alpha__ -#define LOCKUP16 1 -#endif -#ifndef LOCKUP16 -#define LOCKUP16 0 -#endif - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/fcntl.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/string.h> -#include <linux/in.h> -#include <linux/delay.h> -#include <linux/errno.h> -#include <linux/init.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/skbuff.h> -#include <linux/spinlock.h> -#include <linux/bitops.h> -#include <linux/jiffies.h> - -#include <asm/io.h> -#include <asm/irq.h> - -#ifndef NET_DEBUG -#define NET_DEBUG 4 -#endif - -#include "eexpress.h" - -#define EEXP_IO_EXTENT 16 - -/* - * Private data declarations - */ - -struct net_local -{ - unsigned long last_tx; /* jiffies when last transmit started */ - unsigned long init_time; /* jiffies when eexp_hw_init586 called */ - unsigned short rx_first; /* first rx buf, same as RX_BUF_START */ - unsigned short rx_last; /* last rx buf */ - unsigned short rx_ptr; /* first rx buf to look at */ - unsigned short tx_head; /* next free tx buf */ - unsigned short tx_reap; /* first in-use tx buf */ - unsigned short tx_tail; /* previous tx buf to tx_head */ - unsigned short tx_link; /* last known-executing tx buf */ - unsigned short last_tx_restart; /* set to tx_link when we - restart the CU */ - unsigned char started; - unsigned short rx_buf_start; - unsigned short rx_buf_end; - unsigned short num_tx_bufs; - unsigned short num_rx_bufs; - unsigned char width; /* 0 for 16bit, 1 for 8bit */ - unsigned char was_promisc; - unsigned char old_mc_count; - spinlock_t lock; -}; - -/* This is the code and data that is downloaded to the EtherExpress card's - * memory at boot time. - */ - -static unsigned short start_code[] = { -/* 0x0000 */ - 0x0001, /* ISCP: busy - cleared after reset */ - 0x0008,0x0000,0x0000, /* offset,address (lo,hi) of SCB */ - - 0x0000,0x0000, /* SCB: status, commands */ - 0x0000,0x0000, /* links to first command block, - first receive descriptor */ - 0x0000,0x0000, /* CRC error, alignment error counts */ - 0x0000,0x0000, /* out of resources, overrun error counts */ - - 0x0000,0x0000, /* pad */ - 0x0000,0x0000, - -/* 0x20 -- start of 82586 CU program */ -#define CONF_LINK 0x20 - 0x0000,Cmd_Config, - 0x0032, /* link to next command */ - 0x080c, /* 12 bytes follow : fifo threshold=8 */ - 0x2e40, /* don't rx bad frames - * SRDY/ARDY => ext. sync. : preamble len=8 - * take addresses from data buffers - * 6 bytes/address - */ - 0x6000, /* default backoff method & priority - * interframe spacing = 0x60 */ - 0xf200, /* slot time=0x200 - * max collision retry = 0xf */ -#define CONF_PROMISC 0x2e - 0x0000, /* no HDLC : normal CRC : enable broadcast - * disable promiscuous/multicast modes */ - 0x003c, /* minimum frame length = 60 octets) */ - - 0x0000,Cmd_SetAddr, - 0x003e, /* link to next command */ -#define CONF_HWADDR 0x38 - 0x0000,0x0000,0x0000, /* hardware address placed here */ - - 0x0000,Cmd_MCast, - 0x0076, /* link to next command */ -#define CONF_NR_MULTICAST 0x44 - 0x0000, /* number of bytes in multicast address(es) */ -#define CONF_MULTICAST 0x46 - 0x0000, 0x0000, 0x0000, /* some addresses */ - 0x0000, 0x0000, 0x0000, - 0x0000, 0x0000, 0x0000, - 0x0000, 0x0000, 0x0000, - 0x0000, 0x0000, 0x0000, - 0x0000, 0x0000, 0x0000, - 0x0000, 0x0000, 0x0000, - 0x0000, 0x0000, 0x0000, - -#define CONF_DIAG_RESULT 0x76 - 0x0000, Cmd_Diag, - 0x007c, /* link to next command */ - - 0x0000,Cmd_TDR|Cmd_INT, - 0x0084, -#define CONF_TDR_RESULT 0x82 - 0x0000, - - 0x0000,Cmd_END|Cmd_Nop, /* end of configure sequence */ - 0x0084 /* dummy link */ -}; - -/* maps irq number to EtherExpress magic value */ -static char irqrmap[] = { 0,0,1,2,3,4,0,0,0,1,5,6,0,0,0,0 }; - -/* - * Prototypes for Linux interface - */ - -static int eexp_open(struct net_device *dev); -static int eexp_close(struct net_device *dev); -static void eexp_timeout(struct net_device *dev); -static netdev_tx_t eexp_xmit(struct sk_buff *buf, - struct net_device *dev); - -static irqreturn_t eexp_irq(int irq, void *dev_addr); -static void eexp_set_multicast(struct net_device *dev); - -/* - * Prototypes for hardware access functions - */ - -static void eexp_hw_rx_pio(struct net_device *dev); -static void eexp_hw_tx_pio(struct net_device *dev, unsigned short *buf, - unsigned short len); -static int eexp_hw_probe(struct net_device *dev,unsigned short ioaddr); -static unsigned short eexp_hw_readeeprom(unsigned short ioaddr, - unsigned char location); - -static unsigned short eexp_hw_lasttxstat(struct net_device *dev); -static void eexp_hw_txrestart(struct net_device *dev); - -static void eexp_hw_txinit (struct net_device *dev); -static void eexp_hw_rxinit (struct net_device *dev); - -static void eexp_hw_init586 (struct net_device *dev); -static void eexp_setup_filter (struct net_device *dev); - -static char *eexp_ifmap[]={"AUI", "BNC", "RJ45"}; -enum eexp_iftype {AUI=0, BNC=1, TPE=2}; - -#define STARTED_RU 2 -#define STARTED_CU 1 - -/* - * Primitive hardware access functions. - */ - -static inline unsigned short scb_status(struct net_device *dev) -{ - return inw(dev->base_addr + 0xc008); -} - -static inline unsigned short scb_rdcmd(struct net_device *dev) -{ - return inw(dev->base_addr + 0xc00a); -} - -static inline void scb_command(struct net_device *dev, unsigned short cmd) -{ - outw(cmd, dev->base_addr + 0xc00a); -} - -static inline void scb_wrcbl(struct net_device *dev, unsigned short val) -{ - outw(val, dev->base_addr + 0xc00c); -} - -static inline void scb_wrrfa(struct net_device *dev, unsigned short val) -{ - outw(val, dev->base_addr + 0xc00e); -} - -static inline void set_loopback(struct net_device *dev) -{ - outb(inb(dev->base_addr + Config) | 2, dev->base_addr + Config); -} - -static inline void clear_loopback(struct net_device *dev) -{ - outb(inb(dev->base_addr + Config) & ~2, dev->base_addr + Config); -} - -static inline unsigned short int SHADOW(short int addr) -{ - addr &= 0x1f; - if (addr > 0xf) addr += 0x3ff0; - return addr + 0x4000; -} - -/* - * Linux interface - */ - -/* - * checks for presence of EtherExpress card - */ - -static int __init do_express_probe(struct net_device *dev) -{ - unsigned short *port; - static unsigned short ports[] = { 0x240,0x300,0x310,0x270,0x320,0x340,0 }; - unsigned short ioaddr = dev->base_addr; - int dev_irq = dev->irq; - int err; - - dev->if_port = 0xff; /* not set */ - - if (ioaddr&0xfe00) { - if (!request_region(ioaddr, EEXP_IO_EXTENT, "EtherExpress")) - return -EBUSY; - err = eexp_hw_probe(dev,ioaddr); - release_region(ioaddr, EEXP_IO_EXTENT); - return err; - } else if (ioaddr) - return -ENXIO; - - for (port=&ports[0] ; *port ; port++ ) - { - unsigned short sum = 0; - int i; - if (!request_region(*port, EEXP_IO_EXTENT, "EtherExpress")) - continue; - for ( i=0 ; i<4 ; i++ ) - { - unsigned short t; - t = inb(*port + ID_PORT); - sum |= (t>>4) << ((t & 0x03)<<2); - } - if (sum==0xbaba && !eexp_hw_probe(dev,*port)) { - release_region(*port, EEXP_IO_EXTENT); - return 0; - } - release_region(*port, EEXP_IO_EXTENT); - dev->irq = dev_irq; - } - return -ENODEV; -} - -#ifndef MODULE -struct net_device * __init express_probe(int unit) -{ - struct net_device *dev = alloc_etherdev(sizeof(struct net_local)); - int err; - - if (!dev) - return ERR_PTR(-ENOMEM); - - sprintf(dev->name, "eth%d", unit); - netdev_boot_setup_check(dev); - - err = do_express_probe(dev); - if (!err) - return dev; - free_netdev(dev); - return ERR_PTR(err); -} -#endif - -/* - * open and initialize the adapter, ready for use - */ - -static int eexp_open(struct net_device *dev) -{ - int ret; - unsigned short ioaddr = dev->base_addr; - struct net_local *lp = netdev_priv(dev); - -#if NET_DEBUG > 6 - printk(KERN_DEBUG "%s: eexp_open()\n", dev->name); -#endif - - if (!dev->irq || !irqrmap[dev->irq]) - return -ENXIO; - - ret = request_irq(dev->irq, eexp_irq, 0, dev->name, dev); - if (ret) - return ret; - - if (!request_region(ioaddr, EEXP_IO_EXTENT, "EtherExpress")) { - printk(KERN_WARNING "EtherExpress io port %x, is busy.\n" - , ioaddr); - goto err_out1; - } - if (!request_region(ioaddr+0x4000, EEXP_IO_EXTENT, "EtherExpress shadow")) { - printk(KERN_WARNING "EtherExpress io port %x, is busy.\n" - , ioaddr+0x4000); - goto err_out2; - } - if (!request_region(ioaddr+0x8000, EEXP_IO_EXTENT, "EtherExpress shadow")) { - printk(KERN_WARNING "EtherExpress io port %x, is busy.\n" - , ioaddr+0x8000); - goto err_out3; - } - if (!request_region(ioaddr+0xc000, EEXP_IO_EXTENT, "EtherExpress shadow")) { - printk(KERN_WARNING "EtherExpress io port %x, is busy.\n" - , ioaddr+0xc000); - goto err_out4; - } - - if (lp->width) { - printk("%s: forcing ASIC to 8-bit mode\n", dev->name); - outb(inb(dev->base_addr+Config)&~4, dev->base_addr+Config); - } - - eexp_hw_init586(dev); - netif_start_queue(dev); -#if NET_DEBUG > 6 - printk(KERN_DEBUG "%s: leaving eexp_open()\n", dev->name); -#endif - return 0; - - err_out4: - release_region(ioaddr+0x8000, EEXP_IO_EXTENT); - err_out3: - release_region(ioaddr+0x4000, EEXP_IO_EXTENT); - err_out2: - release_region(ioaddr, EEXP_IO_EXTENT); - err_out1: - free_irq(dev->irq, dev); - return -EBUSY; -} - -/* - * close and disable the interface, leaving the 586 in reset. - */ - -static int eexp_close(struct net_device *dev) -{ - unsigned short ioaddr = dev->base_addr; - struct net_local *lp = netdev_priv(dev); - - int irq = dev->irq; - - netif_stop_queue(dev); - - outb(SIRQ_dis|irqrmap[irq],ioaddr+SET_IRQ); - lp->started = 0; - scb_command(dev, SCB_CUsuspend|SCB_RUsuspend); - outb(0,ioaddr+SIGNAL_CA); - free_irq(irq,dev); - outb(i586_RST,ioaddr+EEPROM_Ctrl); - release_region(ioaddr, EEXP_IO_EXTENT); - release_region(ioaddr+0x4000, 16); - release_region(ioaddr+0x8000, 16); - release_region(ioaddr+0xc000, 16); - - return 0; -} - -/* - * This gets called when a higher level thinks we are broken. Check that - * nothing has become jammed in the CU. - */ - -static void unstick_cu(struct net_device *dev) -{ - struct net_local *lp = netdev_priv(dev); - unsigned short ioaddr = dev->base_addr; - - if (lp->started) - { - if (time_after(jiffies, dev_trans_start(dev) + HZ/2)) - { - if (lp->tx_link==lp->last_tx_restart) - { - unsigned short boguscount=200,rsst; - printk(KERN_WARNING "%s: Retransmit timed out, status %04x, resetting...\n", - dev->name, scb_status(dev)); - eexp_hw_txinit(dev); - lp->last_tx_restart = 0; - scb_wrcbl(dev, lp->tx_link); - scb_command(dev, SCB_CUstart); - outb(0,ioaddr+SIGNAL_CA); - while (!SCB_complete(rsst=scb_status(dev))) - { - if (!--boguscount) - { - boguscount=200; - printk(KERN_WARNING "%s: Reset timed out status %04x, retrying...\n", - dev->name,rsst); - scb_wrcbl(dev, lp->tx_link); - scb_command(dev, SCB_CUstart); - outb(0,ioaddr+SIGNAL_CA); - } - } - netif_wake_queue(dev); - } - else - { - unsigned short status = scb_status(dev); - if (SCB_CUdead(status)) - { - unsigned short txstatus = eexp_hw_lasttxstat(dev); - printk(KERN_WARNING "%s: Transmit timed out, CU not active status %04x %04x, restarting...\n", - dev->name, status, txstatus); - eexp_hw_txrestart(dev); - } - else - { - unsigned short txstatus = eexp_hw_lasttxstat(dev); - if (netif_queue_stopped(dev) && !txstatus) - { - printk(KERN_WARNING "%s: CU wedged, status %04x %04x, resetting...\n", - dev->name,status,txstatus); - eexp_hw_init586(dev); - netif_wake_queue(dev); - } - else - { - printk(KERN_WARNING "%s: transmit timed out\n", dev->name); - } - } - } - } - } - else - { - if (time_after(jiffies, lp->init_time + 10)) - { - unsigned short status = scb_status(dev); - printk(KERN_WARNING "%s: i82586 startup timed out, status %04x, resetting...\n", - dev->name, status); - eexp_hw_init586(dev); - netif_wake_queue(dev); - } - } -} - -static void eexp_timeout(struct net_device *dev) -{ - struct net_local *lp = netdev_priv(dev); -#ifdef CONFIG_SMP - unsigned long flags; -#endif - int status; - - disable_irq(dev->irq); - - /* - * Best would be to use synchronize_irq(); spin_lock() here - * lets make it work first.. - */ - -#ifdef CONFIG_SMP - spin_lock_irqsave(&lp->lock, flags); -#endif - - status = scb_status(dev); - unstick_cu(dev); - printk(KERN_INFO "%s: transmit timed out, %s?\n", dev->name, - (SCB_complete(status)?"lost interrupt": - "board on fire")); - dev->stats.tx_errors++; - lp->last_tx = jiffies; - if (!SCB_complete(status)) { - scb_command(dev, SCB_CUabort); - outb(0,dev->base_addr+SIGNAL_CA); - } - netif_wake_queue(dev); -#ifdef CONFIG_SMP - spin_unlock_irqrestore(&lp->lock, flags); -#endif -} - -/* - * Called to transmit a packet, or to allow us to right ourselves - * if the kernel thinks we've died. - */ -static netdev_tx_t eexp_xmit(struct sk_buff *buf, struct net_device *dev) -{ - short length = buf->len; -#ifdef CONFIG_SMP - struct net_local *lp = netdev_priv(dev); - unsigned long flags; -#endif - -#if NET_DEBUG > 6 - printk(KERN_DEBUG "%s: eexp_xmit()\n", dev->name); -#endif - - if (buf->len < ETH_ZLEN) { - if (skb_padto(buf, ETH_ZLEN)) - return NETDEV_TX_OK; - length = ETH_ZLEN; - } - - disable_irq(dev->irq); - - /* - * Best would be to use synchronize_irq(); spin_lock() here - * lets make it work first.. - */ - -#ifdef CONFIG_SMP - spin_lock_irqsave(&lp->lock, flags); -#endif - - { - unsigned short *data = (unsigned short *)buf->data; - - dev->stats.tx_bytes += length; - - eexp_hw_tx_pio(dev,data,length); - } - dev_kfree_skb(buf); -#ifdef CONFIG_SMP - spin_unlock_irqrestore(&lp->lock, flags); -#endif - enable_irq(dev->irq); - return NETDEV_TX_OK; -} - -/* - * Handle an EtherExpress interrupt - * If we've finished initializing, start the RU and CU up. - * If we've already started, reap tx buffers, handle any received packets, - * check to make sure we've not become wedged. - */ - -static unsigned short eexp_start_irq(struct net_device *dev, - unsigned short status) -{ - unsigned short ack_cmd = SCB_ack(status); - struct net_local *lp = netdev_priv(dev); - unsigned short ioaddr = dev->base_addr; - if ((dev->flags & IFF_UP) && !(lp->started & STARTED_CU)) { - short diag_status, tdr_status; - while (SCB_CUstat(status)==2) - status = scb_status(dev); -#if NET_DEBUG > 4 - printk("%s: CU went non-active (status %04x)\n", - dev->name, status); -#endif - - outw(CONF_DIAG_RESULT & ~31, ioaddr + SM_PTR); - diag_status = inw(ioaddr + SHADOW(CONF_DIAG_RESULT)); - if (diag_status & 1<<11) { - printk(KERN_WARNING "%s: 82586 failed self-test\n", - dev->name); - } else if (!(diag_status & 1<<13)) { - printk(KERN_WARNING "%s: 82586 self-test failed to complete\n", dev->name); - } - - outw(CONF_TDR_RESULT & ~31, ioaddr + SM_PTR); - tdr_status = inw(ioaddr + SHADOW(CONF_TDR_RESULT)); - if (tdr_status & (TDR_SHORT|TDR_OPEN)) { - printk(KERN_WARNING "%s: TDR reports cable %s at %d tick%s\n", dev->name, (tdr_status & TDR_SHORT)?"short":"broken", tdr_status & TDR_TIME, ((tdr_status & TDR_TIME) != 1) ? "s" : ""); - } - else if (tdr_status & TDR_XCVRPROBLEM) { - printk(KERN_WARNING "%s: TDR reports transceiver problem\n", dev->name); - } - else if (tdr_status & TDR_LINKOK) { -#if NET_DEBUG > 4 - printk(KERN_DEBUG "%s: TDR reports link OK\n", dev->name); -#endif - } else { - printk("%s: TDR is ga-ga (status %04x)\n", dev->name, - tdr_status); - } - - lp->started |= STARTED_CU; - scb_wrcbl(dev, lp->tx_link); - /* if the RU isn't running, start it now */ - if (!(lp->started & STARTED_RU)) { - ack_cmd |= SCB_RUstart; - scb_wrrfa(dev, lp->rx_buf_start); - lp->rx_ptr = lp->rx_buf_start; - lp->started |= STARTED_RU; - } - ack_cmd |= SCB_CUstart | 0x2000; - } - - if ((dev->flags & IFF_UP) && !(lp->started & STARTED_RU) && SCB_RUstat(status)==4) - lp->started|=STARTED_RU; - - return ack_cmd; -} - -static void eexp_cmd_clear(struct net_device *dev) -{ - unsigned long int oldtime = jiffies; - while (scb_rdcmd(dev) && (time_before(jiffies, oldtime + 10))); - if (scb_rdcmd(dev)) { - printk("%s: command didn't clear\n", dev->name); - } -} - -static irqreturn_t eexp_irq(int dummy, void *dev_info) -{ - struct net_device *dev = dev_info; - struct net_local *lp; - unsigned short ioaddr,status,ack_cmd; - unsigned short old_read_ptr, old_write_ptr; - - lp = netdev_priv(dev); - ioaddr = dev->base_addr; - - spin_lock(&lp->lock); - - old_read_ptr = inw(ioaddr+READ_PTR); - old_write_ptr = inw(ioaddr+WRITE_PTR); - - outb(SIRQ_dis|irqrmap[dev->irq], ioaddr+SET_IRQ); - - status = scb_status(dev); - -#if NET_DEBUG > 4 - printk(KERN_DEBUG "%s: interrupt (status %x)\n", dev->name, status); -#endif - - if (lp->started == (STARTED_CU | STARTED_RU)) { - - do { - eexp_cmd_clear(dev); - - ack_cmd = SCB_ack(status); - scb_command(dev, ack_cmd); - outb(0,ioaddr+SIGNAL_CA); - - eexp_cmd_clear(dev); - - if (SCB_complete(status)) { - if (!eexp_hw_lasttxstat(dev)) { - printk("%s: tx interrupt but no status\n", dev->name); - } - } - - if (SCB_rxdframe(status)) - eexp_hw_rx_pio(dev); - - status = scb_status(dev); - } while (status & 0xc000); - - if (SCB_RUdead(status)) - { - printk(KERN_WARNING "%s: RU stopped: status %04x\n", - dev->name,status); -#if 0 - printk(KERN_WARNING "%s: cur_rfd=%04x, cur_rbd=%04x\n", dev->name, lp->cur_rfd, lp->cur_rbd); - outw(lp->cur_rfd, ioaddr+READ_PTR); - printk(KERN_WARNING "%s: [%04x]\n", dev->name, inw(ioaddr+DATAPORT)); - outw(lp->cur_rfd+6, ioaddr+READ_PTR); - printk(KERN_WARNING "%s: rbd is %04x\n", dev->name, rbd= inw(ioaddr+DATAPORT)); - outw(rbd, ioaddr+READ_PTR); - printk(KERN_WARNING "%s: [%04x %04x] ", dev->name, inw(ioaddr+DATAPORT), inw(ioaddr+DATAPORT)); - outw(rbd+8, ioaddr+READ_PTR); - printk("[%04x]\n", inw(ioaddr+DATAPORT)); -#endif - dev->stats.rx_errors++; -#if 1 - eexp_hw_rxinit(dev); -#else - lp->cur_rfd = lp->first_rfd; -#endif - scb_wrrfa(dev, lp->rx_buf_start); - scb_command(dev, SCB_RUstart); - outb(0,ioaddr+SIGNAL_CA); - } - } else { - if (status & 0x8000) - ack_cmd = eexp_start_irq(dev, status); - else - ack_cmd = SCB_ack(status); - scb_command(dev, ack_cmd); - outb(0,ioaddr+SIGNAL_CA); - } - - eexp_cmd_clear(dev); - - outb(SIRQ_en|irqrmap[dev->irq], ioaddr+SET_IRQ); - -#if NET_DEBUG > 6 - printk("%s: leaving eexp_irq()\n", dev->name); -#endif - outw(old_read_ptr, ioaddr+READ_PTR); - outw(old_write_ptr, ioaddr+WRITE_PTR); - - spin_unlock(&lp->lock); - return IRQ_HANDLED; -} - -/* - * Hardware access functions - */ - -/* - * Set the cable type to use. - */ - -static void eexp_hw_set_interface(struct net_device *dev) -{ - unsigned char oldval = inb(dev->base_addr + 0x300e); - oldval &= ~0x82; - switch (dev->if_port) { - case TPE: - oldval |= 0x2; - case BNC: - oldval |= 0x80; - break; - } - outb(oldval, dev->base_addr+0x300e); - mdelay(20); -} - -/* - * Check all the receive buffers, and hand any received packets - * to the upper levels. Basic sanity check on each frame - * descriptor, though we don't bother trying to fix broken ones. - */ - -static void eexp_hw_rx_pio(struct net_device *dev) -{ - struct net_local *lp = netdev_priv(dev); - unsigned short rx_block = lp->rx_ptr; - unsigned short boguscount = lp->num_rx_bufs; - unsigned short ioaddr = dev->base_addr; - unsigned short status; - -#if NET_DEBUG > 6 - printk(KERN_DEBUG "%s: eexp_hw_rx()\n", dev->name); -#endif - - do { - unsigned short rfd_cmd, rx_next, pbuf, pkt_len; - - outw(rx_block, ioaddr + READ_PTR); - status = inw(ioaddr + DATAPORT); - - if (FD_Done(status)) - { - rfd_cmd = inw(ioaddr + DATAPORT); - rx_next = inw(ioaddr + DATAPORT); - pbuf = inw(ioaddr + DATAPORT); - - outw(pbuf, ioaddr + READ_PTR); - pkt_len = inw(ioaddr + DATAPORT); - - if (rfd_cmd!=0x0000) - { - printk(KERN_WARNING "%s: rfd_cmd not zero:0x%04x\n", - dev->name, rfd_cmd); - continue; - } - else if (pbuf!=rx_block+0x16) - { - printk(KERN_WARNING "%s: rfd and rbd out of sync 0x%04x 0x%04x\n", - dev->name, rx_block+0x16, pbuf); - continue; - } - else if ((pkt_len & 0xc000)!=0xc000) - { - printk(KERN_WARNING "%s: EOF or F not set on received buffer (%04x)\n", - dev->name, pkt_len & 0xc000); - continue; - } - else if (!FD_OK(status)) - { - dev->stats.rx_errors++; - if (FD_CRC(status)) - dev->stats.rx_crc_errors++; - if (FD_Align(status)) - dev->stats.rx_frame_errors++; - if (FD_Resrc(status)) - dev->stats.rx_fifo_errors++; - if (FD_DMA(status)) - dev->stats.rx_over_errors++; - if (FD_Short(status)) - dev->stats.rx_length_errors++; - } - else - { - struct sk_buff *skb; - pkt_len &= 0x3fff; - skb = netdev_alloc_skb(dev, pkt_len + 16); - if (skb == NULL) - { - printk(KERN_WARNING "%s: Memory squeeze, dropping packet\n",dev->name); - dev->stats.rx_dropped++; - break; - } - skb_reserve(skb, 2); - outw(pbuf+10, ioaddr+READ_PTR); - insw(ioaddr+DATAPORT, skb_put(skb,pkt_len),(pkt_len+1)>>1); - skb->protocol = eth_type_trans(skb,dev); - netif_rx(skb); - dev->stats.rx_packets++; - dev->stats.rx_bytes += pkt_len; - } - outw(rx_block, ioaddr+WRITE_PTR); - outw(0, ioaddr+DATAPORT); - outw(0, ioaddr+DATAPORT); - rx_block = rx_next; - } - } while (FD_Done(status) && boguscount--); - lp->rx_ptr = rx_block; -} - -/* - * Hand a packet to the card for transmission - * If we get here, we MUST have already checked - * to make sure there is room in the transmit - * buffer region. - */ - -static void eexp_hw_tx_pio(struct net_device *dev, unsigned short *buf, - unsigned short len) -{ - struct net_local *lp = netdev_priv(dev); - unsigned short ioaddr = dev->base_addr; - - if (LOCKUP16 || lp->width) { - /* Stop the CU so that there is no chance that it - jumps off to a bogus address while we are writing the - pointer to the next transmit packet in 8-bit mode -- - this eliminates the "CU wedged" errors in 8-bit mode. - (Zoltan Szilagyi 10-12-96) */ - scb_command(dev, SCB_CUsuspend); - outw(0xFFFF, ioaddr+SIGNAL_CA); - } - - outw(lp->tx_head, ioaddr + WRITE_PTR); - - outw(0x0000, ioaddr + DATAPORT); - outw(Cmd_INT|Cmd_Xmit, ioaddr + DATAPORT); - outw(lp->tx_head+0x08, ioaddr + DATAPORT); - outw(lp->tx_head+0x0e, ioaddr + DATAPORT); - - outw(0x0000, ioaddr + DATAPORT); - outw(0x0000, ioaddr + DATAPORT); - outw(lp->tx_head+0x08, ioaddr + DATAPORT); - - outw(0x8000|len, ioaddr + DATAPORT); - outw(-1, ioaddr + DATAPORT); - outw(lp->tx_head+0x16, ioaddr + DATAPORT); - outw(0, ioaddr + DATAPORT); - - outsw(ioaddr + DATAPORT, buf, (len+1)>>1); - - outw(lp->tx_tail+0xc, ioaddr + WRITE_PTR); - outw(lp->tx_head, ioaddr + DATAPORT); - - dev->trans_start = jiffies; - lp->tx_tail = lp->tx_head; - if (lp->tx_head==TX_BUF_START+((lp->num_tx_bufs-1)*TX_BUF_SIZE)) - lp->tx_head = TX_BUF_START; - else - lp->tx_head += TX_BUF_SIZE; - if (lp->tx_head != lp->tx_reap) - netif_wake_queue(dev); - - if (LOCKUP16 || lp->width) { - /* Restart the CU so that the packet can actually - be transmitted. (Zoltan Szilagyi 10-12-96) */ - scb_command(dev, SCB_CUresume); - outw(0xFFFF, ioaddr+SIGNAL_CA); - } - - dev->stats.tx_packets++; - lp->last_tx = jiffies; -} - -static const struct net_device_ops eexp_netdev_ops = { - .ndo_open = eexp_open, - .ndo_stop = eexp_close, - .ndo_start_xmit = eexp_xmit, - .ndo_set_rx_mode = eexp_set_multicast, - .ndo_tx_timeout = eexp_timeout, - .ndo_change_mtu = eth_change_mtu, - .ndo_set_mac_address = eth_mac_addr, - .ndo_validate_addr = eth_validate_addr, -}; - -/* - * Sanity check the suspected EtherExpress card - * Read hardware address, reset card, size memory and initialize buffer - * memory pointers. These are held in netdev_priv(), in case someone has more - * than one card in a machine. - */ - -static int __init eexp_hw_probe(struct net_device *dev, unsigned short ioaddr) -{ - unsigned short hw_addr[3]; - unsigned char buswidth; - unsigned int memory_size; - int i; - unsigned short xsum = 0; - struct net_local *lp = netdev_priv(dev); - - printk("%s: EtherExpress 16 at %#x ",dev->name,ioaddr); - - outb(ASIC_RST, ioaddr+EEPROM_Ctrl); - outb(0, ioaddr+EEPROM_Ctrl); - udelay(500); - outb(i586_RST, ioaddr+EEPROM_Ctrl); - - hw_addr[0] = eexp_hw_readeeprom(ioaddr,2); - hw_addr[1] = eexp_hw_readeeprom(ioaddr,3); - hw_addr[2] = eexp_hw_readeeprom(ioaddr,4); - - /* Standard Address or Compaq LTE Address */ - if (!((hw_addr[2]==0x00aa && ((hw_addr[1] & 0xff00)==0x0000)) || - (hw_addr[2]==0x0080 && ((hw_addr[1] & 0xff00)==0x5F00)))) - { - printk(" rejected: invalid address %04x%04x%04x\n", - hw_addr[2],hw_addr[1],hw_addr[0]); - return -ENODEV; - } - - /* Calculate the EEPROM checksum. Carry on anyway if it's bad, - * though. - */ - for (i = 0; i < 64; i++) - xsum += eexp_hw_readeeprom(ioaddr, i); - if (xsum != 0xbaba) - printk(" (bad EEPROM xsum 0x%02x)", xsum); - - dev->base_addr = ioaddr; - for ( i=0 ; i<6 ; i++ ) - dev->dev_addr[i] = ((unsigned char *)hw_addr)[5-i]; - - { - static const char irqmap[] = { 0, 9, 3, 4, 5, 10, 11, 0 }; - unsigned short setupval = eexp_hw_readeeprom(ioaddr,0); - - /* Use the IRQ from EEPROM if none was given */ - if (!dev->irq) - dev->irq = irqmap[setupval>>13]; - - if (dev->if_port == 0xff) { - dev->if_port = !(setupval & 0x1000) ? AUI : - eexp_hw_readeeprom(ioaddr,5) & 0x1 ? TPE : BNC; - } - - buswidth = !((setupval & 0x400) >> 10); - } - - memset(lp, 0, sizeof(struct net_local)); - spin_lock_init(&lp->lock); - - printk("(IRQ %d, %s connector, %d-bit bus", dev->irq, - eexp_ifmap[dev->if_port], buswidth?8:16); - - if (!request_region(dev->base_addr + 0x300e, 1, "EtherExpress")) - return -EBUSY; - - eexp_hw_set_interface(dev); - - release_region(dev->base_addr + 0x300e, 1); - - /* Find out how much RAM we have on the card */ - outw(0, dev->base_addr + WRITE_PTR); - for (i = 0; i < 32768; i++) - outw(0, dev->base_addr + DATAPORT); - - for (memory_size = 0; memory_size < 64; memory_size++) - { - outw(memory_size<<10, dev->base_addr + READ_PTR); - if (inw(dev->base_addr+DATAPORT)) - break; - outw(memory_size<<10, dev->base_addr + WRITE_PTR); - outw(memory_size | 0x5000, dev->base_addr+DATAPORT); - outw(memory_size<<10, dev->base_addr + READ_PTR); - if (inw(dev->base_addr+DATAPORT) != (memory_size | 0x5000)) - break; - } - - /* Sort out the number of buffers. We may have 16, 32, 48 or 64k - * of RAM to play with. - */ - lp->num_tx_bufs = 4; - lp->rx_buf_end = 0x3ff6; - switch (memory_size) - { - case 64: - lp->rx_buf_end += 0x4000; - case 48: - lp->num_tx_bufs += 4; - lp->rx_buf_end += 0x4000; - case 32: - lp->rx_buf_end += 0x4000; - case 16: - printk(", %dk RAM)\n", memory_size); - break; - default: - printk(") bad memory size (%dk).\n", memory_size); - return -ENODEV; - break; - } - - lp->rx_buf_start = TX_BUF_START + (lp->num_tx_bufs*TX_BUF_SIZE); - lp->width = buswidth; - - dev->netdev_ops = &eexp_netdev_ops; - dev->watchdog_timeo = 2*HZ; - - return register_netdev(dev); -} - -/* - * Read a word from the EtherExpress on-board serial EEPROM. - * The EEPROM contains 64 words of 16 bits. - */ -static unsigned short __init eexp_hw_readeeprom(unsigned short ioaddr, - unsigned char location) -{ - unsigned short cmd = 0x180|(location&0x7f); - unsigned short rval = 0,wval = EC_CS|i586_RST; - int i; - - outb(EC_CS|i586_RST,ioaddr+EEPROM_Ctrl); - for (i=0x100 ; i ; i>>=1 ) - { - if (cmd&i) - wval |= EC_Wr; - else - wval &= ~EC_Wr; - - outb(wval,ioaddr+EEPROM_Ctrl); - outb(wval|EC_Clk,ioaddr+EEPROM_Ctrl); - eeprom_delay(); - outb(wval,ioaddr+EEPROM_Ctrl); - eeprom_delay(); - } - wval &= ~EC_Wr; - outb(wval,ioaddr+EEPROM_Ctrl); - for (i=0x8000 ; i ; i>>=1 ) - { - outb(wval|EC_Clk,ioaddr+EEPROM_Ctrl); - eeprom_delay(); - if (inb(ioaddr+EEPROM_Ctrl)&EC_Rd) - rval |= i; - outb(wval,ioaddr+EEPROM_Ctrl); - eeprom_delay(); - } - wval &= ~EC_CS; - outb(wval|EC_Clk,ioaddr+EEPROM_Ctrl); - eeprom_delay(); - outb(wval,ioaddr+EEPROM_Ctrl); - eeprom_delay(); - return rval; -} - -/* - * Reap tx buffers and return last transmit status. - * if ==0 then either: - * a) we're not transmitting anything, so why are we here? - * b) we've died. - * otherwise, Stat_Busy(return) means we've still got some packets - * to transmit, Stat_Done(return) means our buffers should be empty - * again - */ - -static unsigned short eexp_hw_lasttxstat(struct net_device *dev) -{ - struct net_local *lp = netdev_priv(dev); - unsigned short tx_block = lp->tx_reap; - unsigned short status; - - if (!netif_queue_stopped(dev) && lp->tx_head==lp->tx_reap) - return 0x0000; - - do - { - outw(tx_block & ~31, dev->base_addr + SM_PTR); - status = inw(dev->base_addr + SHADOW(tx_block)); - if (!Stat_Done(status)) - { - lp->tx_link = tx_block; - return status; - } - else - { - lp->last_tx_restart = 0; - dev->stats.collisions += Stat_NoColl(status); - if (!Stat_OK(status)) - { - char *whatsup = NULL; - dev->stats.tx_errors++; - if (Stat_Abort(status)) - dev->stats.tx_aborted_errors++; - if (Stat_TNoCar(status)) { - whatsup = "aborted, no carrier"; - dev->stats.tx_carrier_errors++; - } - if (Stat_TNoCTS(status)) { - whatsup = "aborted, lost CTS"; - dev->stats.tx_carrier_errors++; - } - if (Stat_TNoDMA(status)) { - whatsup = "FIFO underran"; - dev->stats.tx_fifo_errors++; - } - if (Stat_TXColl(status)) { - whatsup = "aborted, too many collisions"; - dev->stats.tx_aborted_errors++; - } - if (whatsup) - printk(KERN_INFO "%s: transmit %s\n", - dev->name, whatsup); - } - else - dev->stats.tx_packets++; - } - if (tx_block == TX_BUF_START+((lp->num_tx_bufs-1)*TX_BUF_SIZE)) - lp->tx_reap = tx_block = TX_BUF_START; - else - lp->tx_reap = tx_block += TX_BUF_SIZE; - netif_wake_queue(dev); - } - while (lp->tx_reap != lp->tx_head); - - lp->tx_link = lp->tx_tail + 0x08; - - return status; -} - -/* - * This should never happen. It is called when some higher routine detects - * that the CU has stopped, to try to restart it from the last packet we knew - * we were working on, or the idle loop if we had finished for the time. - */ - -static void eexp_hw_txrestart(struct net_device *dev) -{ - struct net_local *lp = netdev_priv(dev); - unsigned short ioaddr = dev->base_addr; - - lp->last_tx_restart = lp->tx_link; - scb_wrcbl(dev, lp->tx_link); - scb_command(dev, SCB_CUstart); - outb(0,ioaddr+SIGNAL_CA); - - { - unsigned short boguscount=50,failcount=5; - while (!scb_status(dev)) - { - if (!--boguscount) - { - if (--failcount) - { - printk(KERN_WARNING "%s: CU start timed out, status %04x, cmd %04x\n", dev->name, scb_status(dev), scb_rdcmd(dev)); - scb_wrcbl(dev, lp->tx_link); - scb_command(dev, SCB_CUstart); - outb(0,ioaddr+SIGNAL_CA); - boguscount = 100; - } - else - { - printk(KERN_WARNING "%s: Failed to restart CU, resetting board...\n",dev->name); - eexp_hw_init586(dev); - netif_wake_queue(dev); - return; - } - } - } - } -} - -/* - * Writes down the list of transmit buffers into card memory. Each - * entry consists of an 82586 transmit command, followed by a jump - * pointing to itself. When we want to transmit a packet, we write - * the data into the appropriate transmit buffer and then modify the - * preceding jump to point at the new transmit command. This means that - * the 586 command unit is continuously active. - */ - -static void eexp_hw_txinit(struct net_device *dev) -{ - struct net_local *lp = netdev_priv(dev); - unsigned short tx_block = TX_BUF_START; - unsigned short curtbuf; - unsigned short ioaddr = dev->base_addr; - - for ( curtbuf=0 ; curtbuf<lp->num_tx_bufs ; curtbuf++ ) - { - outw(tx_block, ioaddr + WRITE_PTR); - - outw(0x0000, ioaddr + DATAPORT); - outw(Cmd_INT|Cmd_Xmit, ioaddr + DATAPORT); - outw(tx_block+0x08, ioaddr + DATAPORT); - outw(tx_block+0x0e, ioaddr + DATAPORT); - - outw(0x0000, ioaddr + DATAPORT); - outw(0x0000, ioaddr + DATAPORT); - outw(tx_block+0x08, ioaddr + DATAPORT); - - outw(0x8000, ioaddr + DATAPORT); - outw(-1, ioaddr + DATAPORT); - outw(tx_block+0x16, ioaddr + DATAPORT); - outw(0x0000, ioaddr + DATAPORT); - - tx_block += TX_BUF_SIZE; - } - lp->tx_head = TX_BUF_START; - lp->tx_reap = TX_BUF_START; - lp->tx_tail = tx_block - TX_BUF_SIZE; - lp->tx_link = lp->tx_tail + 0x08; - lp->rx_buf_start = tx_block; - -} - -/* - * Write the circular list of receive buffer descriptors to card memory. - * The end of the list isn't marked, which means that the 82586 receive - * unit will loop until buffers become available (this avoids it giving us - * "out of resources" messages). - */ - -static void eexp_hw_rxinit(struct net_device *dev) -{ - struct net_local *lp = netdev_priv(dev); - unsigned short rx_block = lp->rx_buf_start; - unsigned short ioaddr = dev->base_addr; - - lp->num_rx_bufs = 0; - lp->rx_first = lp->rx_ptr = rx_block; - do - { - lp->num_rx_bufs++; - - outw(rx_block, ioaddr + WRITE_PTR); - - outw(0, ioaddr + DATAPORT); outw(0, ioaddr+DATAPORT); - outw(rx_block + RX_BUF_SIZE, ioaddr+DATAPORT); - outw(0xffff, ioaddr+DATAPORT); - - outw(0x0000, ioaddr+DATAPORT); - outw(0xdead, ioaddr+DATAPORT); - outw(0xdead, ioaddr+DATAPORT); - outw(0xdead, ioaddr+DATAPORT); - outw(0xdead, ioaddr+DATAPORT); - outw(0xdead, ioaddr+DATAPORT); - outw(0xdead, ioaddr+DATAPORT); - - outw(0x0000, ioaddr+DATAPORT); - outw(rx_block + RX_BUF_SIZE + 0x16, ioaddr+DATAPORT); - outw(rx_block + 0x20, ioaddr+DATAPORT); - outw(0, ioaddr+DATAPORT); - outw(RX_BUF_SIZE-0x20, ioaddr+DATAPORT); - - lp->rx_last = rx_block; - rx_block += RX_BUF_SIZE; - } while (rx_block <= lp->rx_buf_end-RX_BUF_SIZE); - - - /* Make first Rx frame descriptor point to first Rx buffer - descriptor */ - outw(lp->rx_first + 6, ioaddr+WRITE_PTR); - outw(lp->rx_first + 0x16, ioaddr+DATAPORT); - - /* Close Rx frame descriptor ring */ - outw(lp->rx_last + 4, ioaddr+WRITE_PTR); - outw(lp->rx_first, ioaddr+DATAPORT); - - /* Close Rx buffer descriptor ring */ - outw(lp->rx_last + 0x16 + 2, ioaddr+WRITE_PTR); - outw(lp->rx_first + 0x16, ioaddr+DATAPORT); - -} - -/* - * Un-reset the 586, and start the configuration sequence. We don't wait for - * this to finish, but allow the interrupt handler to start the CU and RU for - * us. We can't start the receive/transmission system up before we know that - * the hardware is configured correctly. - */ - -static void eexp_hw_init586(struct net_device *dev) -{ - struct net_local *lp = netdev_priv(dev); - unsigned short ioaddr = dev->base_addr; - int i; - -#if NET_DEBUG > 6 - printk("%s: eexp_hw_init586()\n", dev->name); -#endif - - lp->started = 0; - - set_loopback(dev); - - outb(SIRQ_dis|irqrmap[dev->irq],ioaddr+SET_IRQ); - - /* Download the startup code */ - outw(lp->rx_buf_end & ~31, ioaddr + SM_PTR); - outw(lp->width?0x0001:0x0000, ioaddr + 0x8006); - outw(0x0000, ioaddr + 0x8008); - outw(0x0000, ioaddr + 0x800a); - outw(0x0000, ioaddr + 0x800c); - outw(0x0000, ioaddr + 0x800e); - - for (i = 0; i < ARRAY_SIZE(start_code) * 2; i+=32) { - int j; - outw(i, ioaddr + SM_PTR); - for (j = 0; j < 16 && (i+j)/2 < ARRAY_SIZE(start_code); j+=2) - outw(start_code[(i+j)/2], - ioaddr+0x4000+j); - for (j = 0; j < 16 && (i+j+16)/2 < ARRAY_SIZE(start_code); j+=2) - outw(start_code[(i+j+16)/2], - ioaddr+0x8000+j); - } - - /* Do we want promiscuous mode or multicast? */ - outw(CONF_PROMISC & ~31, ioaddr+SM_PTR); - i = inw(ioaddr+SHADOW(CONF_PROMISC)); - outw((dev->flags & IFF_PROMISC)?(i|1):(i & ~1), - ioaddr+SHADOW(CONF_PROMISC)); - lp->was_promisc = dev->flags & IFF_PROMISC; -#if 0 - eexp_setup_filter(dev); -#endif - - /* Write our hardware address */ - outw(CONF_HWADDR & ~31, ioaddr+SM_PTR); - outw(((unsigned short *)dev->dev_addr)[0], ioaddr+SHADOW(CONF_HWADDR)); - outw(((unsigned short *)dev->dev_addr)[1], - ioaddr+SHADOW(CONF_HWADDR+2)); - outw(((unsigned short *)dev->dev_addr)[2], - ioaddr+SHADOW(CONF_HWADDR+4)); - - eexp_hw_txinit(dev); - eexp_hw_rxinit(dev); - - outb(0,ioaddr+EEPROM_Ctrl); - mdelay(5); - - scb_command(dev, 0xf000); - outb(0,ioaddr+SIGNAL_CA); - - outw(0, ioaddr+SM_PTR); - - { - unsigned short rboguscount=50,rfailcount=5; - while (inw(ioaddr+0x4000)) - { - if (!--rboguscount) - { - printk(KERN_WARNING "%s: i82586 reset timed out, kicking...\n", - dev->name); - scb_command(dev, 0); - outb(0,ioaddr+SIGNAL_CA); - rboguscount = 100; - if (!--rfailcount) - { - printk(KERN_WARNING "%s: i82586 not responding, giving up.\n", - dev->name); - return; - } - } - } - } - - scb_wrcbl(dev, CONF_LINK); - scb_command(dev, 0xf000|SCB_CUstart); - outb(0,ioaddr+SIGNAL_CA); - - { - unsigned short iboguscount=50,ifailcount=5; - while (!scb_status(dev)) - { - if (!--iboguscount) - { - if (--ifailcount) - { - printk(KERN_WARNING "%s: i82586 initialization timed out, status %04x, cmd %04x\n", - dev->name, scb_status(dev), scb_rdcmd(dev)); - scb_wrcbl(dev, CONF_LINK); - scb_command(dev, 0xf000|SCB_CUstart); - outb(0,ioaddr+SIGNAL_CA); - iboguscount = 100; - } - else - { - printk(KERN_WARNING "%s: Failed to initialize i82586, giving up.\n",dev->name); - return; - } - } - } - } - - clear_loopback(dev); - outb(SIRQ_en|irqrmap[dev->irq],ioaddr+SET_IRQ); - - lp->init_time = jiffies; -#if NET_DEBUG > 6 - printk("%s: leaving eexp_hw_init586()\n", dev->name); -#endif -} - -static void eexp_setup_filter(struct net_device *dev) -{ - struct netdev_hw_addr *ha; - unsigned short ioaddr = dev->base_addr; - int count = netdev_mc_count(dev); - int i; - if (count > 8) { - printk(KERN_INFO "%s: too many multicast addresses (%d)\n", - dev->name, count); - count = 8; - } - - outw(CONF_NR_MULTICAST & ~31, ioaddr+SM_PTR); - outw(6*count, ioaddr+SHADOW(CONF_NR_MULTICAST)); - i = 0; - netdev_for_each_mc_addr(ha, dev) { - unsigned short *data = (unsigned short *) ha->addr; - - if (i == count) - break; - outw((CONF_MULTICAST+(6*i)) & ~31, ioaddr+SM_PTR); - outw(data[0], ioaddr+SHADOW(CONF_MULTICAST+(6*i))); - outw((CONF_MULTICAST+(6*i)+2) & ~31, ioaddr+SM_PTR); - outw(data[1], ioaddr+SHADOW(CONF_MULTICAST+(6*i)+2)); - outw((CONF_MULTICAST+(6*i)+4) & ~31, ioaddr+SM_PTR); - outw(data[2], ioaddr+SHADOW(CONF_MULTICAST+(6*i)+4)); - i++; - } -} - -/* - * Set or clear the multicast filter for this adaptor. - */ -static void -eexp_set_multicast(struct net_device *dev) -{ - unsigned short ioaddr = dev->base_addr; - struct net_local *lp = netdev_priv(dev); - int kick = 0, i; - if ((dev->flags & IFF_PROMISC) != lp->was_promisc) { - outw(CONF_PROMISC & ~31, ioaddr+SM_PTR); - i = inw(ioaddr+SHADOW(CONF_PROMISC)); - outw((dev->flags & IFF_PROMISC)?(i|1):(i & ~1), - ioaddr+SHADOW(CONF_PROMISC)); - lp->was_promisc = dev->flags & IFF_PROMISC; - kick = 1; - } - if (!(dev->flags & IFF_PROMISC)) { - eexp_setup_filter(dev); - if (lp->old_mc_count != netdev_mc_count(dev)) { - kick = 1; - lp->old_mc_count = netdev_mc_count(dev); - } - } - if (kick) { - unsigned long oj; - scb_command(dev, SCB_CUsuspend); - outb(0, ioaddr+SIGNAL_CA); - outb(0, ioaddr+SIGNAL_CA); -#if 0 - printk("%s: waiting for CU to go suspended\n", dev->name); -#endif - oj = jiffies; - while ((SCB_CUstat(scb_status(dev)) == 2) && - (time_before(jiffies, oj + 2000))); - if (SCB_CUstat(scb_status(dev)) == 2) - printk("%s: warning, CU didn't stop\n", dev->name); - lp->started &= ~(STARTED_CU); - scb_wrcbl(dev, CONF_LINK); - scb_command(dev, SCB_CUstart); - outb(0, ioaddr+SIGNAL_CA); - } -} - - -/* - * MODULE stuff - */ - -#ifdef MODULE - -#define EEXP_MAX_CARDS 4 /* max number of cards to support */ - -static struct net_device *dev_eexp[EEXP_MAX_CARDS]; -static int irq[EEXP_MAX_CARDS]; -static int io[EEXP_MAX_CARDS]; - -module_param_array(io, int, NULL, 0); -module_param_array(irq, int, NULL, 0); -MODULE_PARM_DESC(io, "EtherExpress 16 I/O base address(es)"); -MODULE_PARM_DESC(irq, "EtherExpress 16 IRQ number(s)"); -MODULE_LICENSE("GPL"); - - -/* Ideally the user would give us io=, irq= for every card. If any parameters - * are specified, we verify and then use them. If no parameters are given, we - * autoprobe for one card only. - */ -int __init init_module(void) -{ - struct net_device *dev; - int this_dev, found = 0; - - for (this_dev = 0; this_dev < EEXP_MAX_CARDS; this_dev++) { - dev = alloc_etherdev(sizeof(struct net_local)); - dev->irq = irq[this_dev]; - dev->base_addr = io[this_dev]; - if (io[this_dev] == 0) { - if (this_dev) - break; - printk(KERN_NOTICE "eexpress.c: Module autoprobe not recommended, give io=xx.\n"); - } - if (do_express_probe(dev) == 0) { - dev_eexp[this_dev] = dev; - found++; - continue; - } - printk(KERN_WARNING "eexpress.c: Failed to register card at 0x%x.\n", io[this_dev]); - free_netdev(dev); - break; - } - if (found) - return 0; - return -ENXIO; -} - -void __exit cleanup_module(void) -{ - int this_dev; - - for (this_dev = 0; this_dev < EEXP_MAX_CARDS; this_dev++) { - struct net_device *dev = dev_eexp[this_dev]; - if (dev) { - unregister_netdev(dev); - free_netdev(dev); - } - } -} -#endif - -/* - * Local Variables: - * c-file-style: "linux" - * tab-width: 8 - * End: - */ diff --git a/drivers/net/ethernet/i825xx/eexpress.h b/drivers/net/ethernet/i825xx/eexpress.h deleted file mode 100644 index dc9c6ea289e9..000000000000 --- a/drivers/net/ethernet/i825xx/eexpress.h +++ /dev/null @@ -1,179 +0,0 @@ -/* - * eexpress.h: Intel EtherExpress16 defines - */ - -/* - * EtherExpress card register addresses - * as offsets from the base IO region (dev->base_addr) - */ - -#define DATAPORT 0x0000 -#define WRITE_PTR 0x0002 -#define READ_PTR 0x0004 -#define SIGNAL_CA 0x0006 -#define SET_IRQ 0x0007 -#define SM_PTR 0x0008 -#define MEM_Dec 0x000a -#define MEM_Ctrl 0x000b -#define MEM_Page_Ctrl 0x000c -#define Config 0x000d -#define EEPROM_Ctrl 0x000e -#define ID_PORT 0x000f -#define MEM_ECtrl 0x000f - -/* - * card register defines - */ - -/* SET_IRQ */ -#define SIRQ_en 0x08 -#define SIRQ_dis 0x00 - -/* EEPROM_Ctrl */ -#define EC_Clk 0x01 -#define EC_CS 0x02 -#define EC_Wr 0x04 -#define EC_Rd 0x08 -#define ASIC_RST 0x40 -#define i586_RST 0x80 - -#define eeprom_delay() { udelay(40); } - -/* - * i82586 Memory Configuration - */ - -/* (System Configuration Pointer) System start up block, read after 586_RST */ -#define SCP_START 0xfff6 - -/* Intermediate System Configuration Pointer */ -#define ISCP_START 0x0000 - -/* System Command Block */ -#define SCB_START 0x0008 - -/* Start of buffer region. Everything before this is used for control - * structures and the CU configuration program. The memory layout is - * determined in eexp_hw_probe(), once we know how much memory is - * available on the card. - */ - -#define TX_BUF_START 0x0100 - -#define TX_BUF_SIZE ((24+ETH_FRAME_LEN+31)&~0x1f) -#define RX_BUF_SIZE ((32+ETH_FRAME_LEN+31)&~0x1f) - -/* - * SCB defines - */ - -/* these functions take the SCB status word and test the relevant status bit */ -#define SCB_complete(s) (((s) & 0x8000) != 0) -#define SCB_rxdframe(s) (((s) & 0x4000) != 0) -#define SCB_CUdead(s) (((s) & 0x2000) != 0) -#define SCB_RUdead(s) (((s) & 0x1000) != 0) -#define SCB_ack(s) ((s) & 0xf000) - -/* Command unit status: 0=idle, 1=suspended, 2=active */ -#define SCB_CUstat(s) (((s)&0x0300)>>8) - -/* Receive unit status: 0=idle, 1=suspended, 2=out of resources, 4=ready */ -#define SCB_RUstat(s) (((s)&0x0070)>>4) - -/* SCB commands */ -#define SCB_CUnop 0x0000 -#define SCB_CUstart 0x0100 -#define SCB_CUresume 0x0200 -#define SCB_CUsuspend 0x0300 -#define SCB_CUabort 0x0400 -#define SCB_resetchip 0x0080 - -#define SCB_RUnop 0x0000 -#define SCB_RUstart 0x0010 -#define SCB_RUresume 0x0020 -#define SCB_RUsuspend 0x0030 -#define SCB_RUabort 0x0040 - -/* - * Command block defines - */ - -#define Stat_Done(s) (((s) & 0x8000) != 0) -#define Stat_Busy(s) (((s) & 0x4000) != 0) -#define Stat_OK(s) (((s) & 0x2000) != 0) -#define Stat_Abort(s) (((s) & 0x1000) != 0) -#define Stat_STFail (((s) & 0x0800) != 0) -#define Stat_TNoCar(s) (((s) & 0x0400) != 0) -#define Stat_TNoCTS(s) (((s) & 0x0200) != 0) -#define Stat_TNoDMA(s) (((s) & 0x0100) != 0) -#define Stat_TDefer(s) (((s) & 0x0080) != 0) -#define Stat_TColl(s) (((s) & 0x0040) != 0) -#define Stat_TXColl(s) (((s) & 0x0020) != 0) -#define Stat_NoColl(s) ((s) & 0x000f) - -/* Cmd_END will end AFTER the command if this is the first - * command block after an SCB_CUstart, but BEFORE the command - * for all subsequent commands. Best strategy is to place - * Cmd_INT on the last command in the sequence, followed by a - * dummy Cmd_Nop with Cmd_END after this. - */ - -#define Cmd_END 0x8000 -#define Cmd_SUS 0x4000 -#define Cmd_INT 0x2000 - -#define Cmd_Nop 0x0000 -#define Cmd_SetAddr 0x0001 -#define Cmd_Config 0x0002 -#define Cmd_MCast 0x0003 -#define Cmd_Xmit 0x0004 -#define Cmd_TDR 0x0005 -#define Cmd_Dump 0x0006 -#define Cmd_Diag 0x0007 - - -/* - * Frame Descriptor (Receive block) defines - */ - -#define FD_Done(s) (((s) & 0x8000) != 0) -#define FD_Busy(s) (((s) & 0x4000) != 0) -#define FD_OK(s) (((s) & 0x2000) != 0) - -#define FD_CRC(s) (((s) & 0x0800) != 0) -#define FD_Align(s) (((s) & 0x0400) != 0) -#define FD_Resrc(s) (((s) & 0x0200) != 0) -#define FD_DMA(s) (((s) & 0x0100) != 0) -#define FD_Short(s) (((s) & 0x0080) != 0) -#define FD_NoEOF(s) (((s) & 0x0040) != 0) - -struct rfd_header { - volatile unsigned long flags; - volatile unsigned short link; - volatile unsigned short rbd_offset; - volatile unsigned short dstaddr1; - volatile unsigned short dstaddr2; - volatile unsigned short dstaddr3; - volatile unsigned short srcaddr1; - volatile unsigned short srcaddr2; - volatile unsigned short srcaddr3; - volatile unsigned short length; - - /* This is actually a Receive Buffer Descriptor. The way we - * arrange memory means that an RBD always follows the RFD that - * points to it, so they might as well be in the same structure. - */ - volatile unsigned short actual_count; - volatile unsigned short next_rbd; - volatile unsigned short buf_addr1; - volatile unsigned short buf_addr2; - volatile unsigned short size; -}; - -/* Returned data from the Time Domain Reflectometer */ - -#define TDR_LINKOK (1<<15) -#define TDR_XCVRPROBLEM (1<<14) -#define TDR_OPEN (1<<13) -#define TDR_SHORT (1<<12) -#define TDR_TIME 0x7ff |