diff options
Diffstat (limited to 'drivers/usb')
| -rw-r--r-- | drivers/usb/core/hcd-pci.c | 1 | ||||
| -rw-r--r-- | drivers/usb/host/ehci-pci.c | 10 | ||||
| -rw-r--r-- | drivers/usb/host/ohci-hcd.c | 12 | ||||
| -rw-r--r-- | drivers/usb/host/ohci-pci.c | 4 |
4 files changed, 17 insertions, 10 deletions
diff --git a/drivers/usb/core/hcd-pci.c b/drivers/usb/core/hcd-pci.c index 99432785f438..507741ed4482 100644 --- a/drivers/usb/core/hcd-pci.c +++ b/drivers/usb/core/hcd-pci.c @@ -128,6 +128,7 @@ int usb_hcd_pci_probe(struct pci_dev *dev, const struct pci_device_id *id) } pci_set_master(dev); + device_set_wakeup_enable(&dev->dev, 1); retval = usb_add_hcd(hcd, dev->irq, IRQF_DISABLED | IRQF_SHARED); if (retval != 0) diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c index 6af47a0937b8..bdc6e86e1f8b 100644 --- a/drivers/usb/host/ehci-pci.c +++ b/drivers/usb/host/ehci-pci.c @@ -219,15 +219,19 @@ static int ehci_pci_setup(struct usb_hcd *hcd) /* Serial Bus Release Number is at PCI 0x60 offset */ pci_read_config_byte(pdev, 0x60, &ehci->sbrn); - /* Workaround current PCI init glitch: wakeup bits aren't - * being set from PCI PM capability. + /* Keep this around for a while just in case some EHCI + * implementation uses legacy PCI PM support. This test + * can be removed on 17 Dec 2009 if the dev_warn() hasn't + * been triggered by then. */ if (!device_can_wakeup(&pdev->dev)) { u16 port_wake; pci_read_config_word(pdev, 0x62, &port_wake); - if (port_wake & 0x0001) + if (port_wake & 0x0001) { + dev_warn(&pdev->dev, "Enabling legacy PCI PM\n"); device_init_wakeup(&pdev->dev, 1); + } } #ifdef CONFIG_USB_SUSPEND diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c index 8aa3f4556a32..65a9609f4ad6 100644 --- a/drivers/usb/host/ohci-hcd.c +++ b/drivers/usb/host/ohci-hcd.c @@ -589,13 +589,15 @@ static int ohci_run (struct ohci_hcd *ohci) /* also: power/overcurrent flags in roothub.a */ } - /* Reset USB nearly "by the book". RemoteWakeupConnected was - * saved if boot firmware (BIOS/SMM/...) told us it's connected, - * or if bus glue did the same (e.g. for PCI add-in cards with - * PCI PM support). + /* Reset USB nearly "by the book". RemoteWakeupConnected has + * to be checked in case boot firmware (BIOS/SMM/...) has set up + * wakeup in a way the bus isn't aware of (e.g., legacy PCI PM). + * If the bus glue detected wakeup capability then it should + * already be enabled. Either way, if wakeup should be enabled + * but isn't, we'll enable it now. */ if ((ohci->hc_control & OHCI_CTRL_RWC) != 0 - && !device_may_wakeup(hcd->self.controller)) + && !device_can_wakeup(hcd->self.controller)) device_init_wakeup(hcd->self.controller, 1); switch (ohci->hc_control & OHCI_CTRL_HCFS) { diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c index 8380cc2e961a..8b28ae7865ba 100644 --- a/drivers/usb/host/ohci-pci.c +++ b/drivers/usb/host/ohci-pci.c @@ -355,9 +355,9 @@ static int __devinit ohci_pci_start (struct usb_hcd *hcd) /* RWC may not be set for add-in PCI cards, since boot * firmware probably ignored them. This transfers PCI - * PM wakeup capabilities (once the PCI layer is fixed). + * PM wakeup capabilities. */ - if (device_may_wakeup(&pdev->dev)) + if (device_can_wakeup(&pdev->dev)) ohci->hc_control |= OHCI_CTRL_RWC; } #endif /* CONFIG_PM */ |