diff options
Diffstat (limited to 'drivers/usb/musb')
-rw-r--r-- | drivers/usb/musb/Kconfig | 5 | ||||
-rw-r--r-- | drivers/usb/musb/am35x.c | 63 | ||||
-rw-r--r-- | drivers/usb/musb/blackfin.c | 13 | ||||
-rw-r--r-- | drivers/usb/musb/da8xx.c | 49 | ||||
-rw-r--r-- | drivers/usb/musb/davinci.c | 59 | ||||
-rw-r--r-- | drivers/usb/musb/musb_am335x.c | 2 | ||||
-rw-r--r-- | drivers/usb/musb/musb_core.c | 72 | ||||
-rw-r--r-- | drivers/usb/musb/musb_core.h | 3 | ||||
-rw-r--r-- | drivers/usb/musb/musb_cppi41.c | 172 | ||||
-rw-r--r-- | drivers/usb/musb/musb_dsps.c | 99 | ||||
-rw-r--r-- | drivers/usb/musb/musb_gadget.c | 12 | ||||
-rw-r--r-- | drivers/usb/musb/musb_host.c | 2 | ||||
-rw-r--r-- | drivers/usb/musb/musb_virthub.c | 65 | ||||
-rw-r--r-- | drivers/usb/musb/omap2430.c | 54 | ||||
-rw-r--r-- | drivers/usb/musb/tusb6010.c | 49 | ||||
-rw-r--r-- | drivers/usb/musb/ux500.c | 15 |
16 files changed, 425 insertions, 309 deletions
diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig index c258a97ef1b0..57dfc0cedb00 100644 --- a/drivers/usb/musb/Kconfig +++ b/drivers/usb/musb/Kconfig @@ -75,6 +75,7 @@ config USB_MUSB_TUSB6010 config USB_MUSB_OMAP2PLUS tristate "OMAP2430 and onwards" depends on ARCH_OMAP2PLUS + select GENERIC_PHY config USB_MUSB_AM35X tristate "AM35x" @@ -90,7 +91,7 @@ config USB_MUSB_BLACKFIN depends on (BF54x && !BF544) || (BF52x && ! BF522 && !BF523) config USB_MUSB_UX500 - tristate "U8500 and U5500" + tristate "Ux500 platforms" endchoice @@ -112,7 +113,7 @@ choice allow using DMA on multiplatform kernels. config USB_UX500_DMA - bool 'ST Ericsson U8500 and U5500' + bool 'ST Ericsson Ux500' depends on USB_MUSB_UX500 help Enable DMA transfers on UX500 platforms. diff --git a/drivers/usb/musb/am35x.c b/drivers/usb/musb/am35x.c index 5c310c664218..ca45b39db5b9 100644 --- a/drivers/usb/musb/am35x.c +++ b/drivers/usb/musb/am35x.c @@ -89,7 +89,6 @@ struct am35x_glue { struct clk *phy_clk; struct clk *clk; }; -#define glue_to_musb(g) platform_get_drvdata(g->musb) /* * am35x_musb_enable - enable interrupts @@ -452,14 +451,18 @@ static const struct musb_platform_ops am35x_ops = { .set_vbus = am35x_musb_set_vbus, }; -static u64 am35x_dmamask = DMA_BIT_MASK(32); +static const struct platform_device_info am35x_dev_info = { + .name = "musb-hdrc", + .id = PLATFORM_DEVID_AUTO, + .dma_mask = DMA_BIT_MASK(32), +}; static int am35x_probe(struct platform_device *pdev) { struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev); struct platform_device *musb; struct am35x_glue *glue; - + struct platform_device_info pinfo; struct clk *phy_clk; struct clk *clk; @@ -471,12 +474,6 @@ static int am35x_probe(struct platform_device *pdev) goto err0; } - musb = platform_device_alloc("musb-hdrc", PLATFORM_DEVID_AUTO); - if (!musb) { - dev_err(&pdev->dev, "failed to allocate musb device\n"); - goto err1; - } - phy_clk = clk_get(&pdev->dev, "fck"); if (IS_ERR(phy_clk)) { dev_err(&pdev->dev, "failed to get PHY clock\n"); @@ -503,12 +500,7 @@ static int am35x_probe(struct platform_device *pdev) goto err6; } - musb->dev.parent = &pdev->dev; - musb->dev.dma_mask = &am35x_dmamask; - musb->dev.coherent_dma_mask = am35x_dmamask; - glue->dev = &pdev->dev; - glue->musb = musb; glue->phy_clk = phy_clk; glue->clk = clk; @@ -516,22 +508,17 @@ static int am35x_probe(struct platform_device *pdev) platform_set_drvdata(pdev, glue); - ret = platform_device_add_resources(musb, pdev->resource, - pdev->num_resources); - if (ret) { - dev_err(&pdev->dev, "failed to add resources\n"); - goto err7; - } - - ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); - if (ret) { - dev_err(&pdev->dev, "failed to add platform_data\n"); - goto err7; - } - - ret = platform_device_add(musb); - if (ret) { - dev_err(&pdev->dev, "failed to register musb device\n"); + pinfo = am35x_dev_info; + pinfo.parent = &pdev->dev; + pinfo.res = pdev->resource; + pinfo.num_res = pdev->num_resources; + pinfo.data = pdata; + pinfo.size_data = sizeof(*pdata); + + glue->musb = musb = platform_device_register_full(&pinfo); + if (IS_ERR(musb)) { + ret = PTR_ERR(musb); + dev_err(&pdev->dev, "failed to register musb device: %d\n", ret); goto err7; } @@ -550,9 +537,6 @@ err4: clk_put(phy_clk); err3: - platform_device_put(musb); - -err1: kfree(glue); err0: @@ -615,23 +599,16 @@ static int am35x_resume(struct device *dev) return 0; } - -static struct dev_pm_ops am35x_pm_ops = { - .suspend = am35x_suspend, - .resume = am35x_resume, -}; - -#define DEV_PM_OPS &am35x_pm_ops -#else -#define DEV_PM_OPS NULL #endif +static SIMPLE_DEV_PM_OPS(am35x_pm_ops, am35x_suspend, am35x_resume); + static struct platform_driver am35x_driver = { .probe = am35x_probe, .remove = am35x_remove, .driver = { .name = "musb-am35x", - .pm = DEV_PM_OPS, + .pm = &am35x_pm_ops, }, }; diff --git a/drivers/usb/musb/blackfin.c b/drivers/usb/musb/blackfin.c index 72e2056b6082..d9692f78e227 100644 --- a/drivers/usb/musb/blackfin.c +++ b/drivers/usb/musb/blackfin.c @@ -561,23 +561,16 @@ static int bfin_resume(struct device *dev) return 0; } - -static struct dev_pm_ops bfin_pm_ops = { - .suspend = bfin_suspend, - .resume = bfin_resume, -}; - -#define DEV_PM_OPS &bfin_pm_ops -#else -#define DEV_PM_OPS NULL #endif +static SIMPLE_DEV_PM_OPS(bfin_pm_ops, bfin_suspend, bfin_resume); + static struct platform_driver bfin_driver = { .probe = bfin_probe, .remove = __exit_p(bfin_remove), .driver = { .name = "musb-blackfin", - .pm = DEV_PM_OPS, + .pm = &bfin_pm_ops, }, }; diff --git a/drivers/usb/musb/da8xx.c b/drivers/usb/musb/da8xx.c index d9ddf4122f37..2f2c1cb36421 100644 --- a/drivers/usb/musb/da8xx.c +++ b/drivers/usb/musb/da8xx.c @@ -472,7 +472,11 @@ static const struct musb_platform_ops da8xx_ops = { .set_vbus = da8xx_musb_set_vbus, }; -static u64 da8xx_dmamask = DMA_BIT_MASK(32); +static const struct platform_device_info da8xx_dev_info = { + .name = "musb-hdrc", + .id = PLATFORM_DEVID_AUTO, + .dma_mask = DMA_BIT_MASK(32), +}; static int da8xx_probe(struct platform_device *pdev) { @@ -480,7 +484,7 @@ static int da8xx_probe(struct platform_device *pdev) struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev); struct platform_device *musb; struct da8xx_glue *glue; - + struct platform_device_info pinfo; struct clk *clk; int ret = -ENOMEM; @@ -491,12 +495,6 @@ static int da8xx_probe(struct platform_device *pdev) goto err0; } - musb = platform_device_alloc("musb-hdrc", PLATFORM_DEVID_AUTO); - if (!musb) { - dev_err(&pdev->dev, "failed to allocate musb device\n"); - goto err1; - } - clk = clk_get(&pdev->dev, "usb20"); if (IS_ERR(clk)) { dev_err(&pdev->dev, "failed to get clock\n"); @@ -510,12 +508,7 @@ static int da8xx_probe(struct platform_device *pdev) goto err4; } - musb->dev.parent = &pdev->dev; - musb->dev.dma_mask = &da8xx_dmamask; - musb->dev.coherent_dma_mask = da8xx_dmamask; - glue->dev = &pdev->dev; - glue->musb = musb; glue->clk = clk; pdata->platform_ops = &da8xx_ops; @@ -535,22 +528,17 @@ static int da8xx_probe(struct platform_device *pdev) musb_resources[1].end = pdev->resource[1].end; musb_resources[1].flags = pdev->resource[1].flags; - ret = platform_device_add_resources(musb, musb_resources, - ARRAY_SIZE(musb_resources)); - if (ret) { - dev_err(&pdev->dev, "failed to add resources\n"); - goto err5; - } - - ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); - if (ret) { - dev_err(&pdev->dev, "failed to add platform_data\n"); - goto err5; - } - - ret = platform_device_add(musb); - if (ret) { - dev_err(&pdev->dev, "failed to register musb device\n"); + pinfo = da8xx_dev_info; + pinfo.parent = &pdev->dev; + pinfo.res = musb_resources; + pinfo.num_res = ARRAY_SIZE(musb_resources); + pinfo.data = pdata; + pinfo.size_data = sizeof(*pdata); + + glue->musb = musb = platform_device_register_full(&pinfo); + if (IS_ERR(musb)) { + ret = PTR_ERR(musb); + dev_err(&pdev->dev, "failed to register musb device: %d\n", ret); goto err5; } @@ -563,9 +551,6 @@ err4: clk_put(clk); err3: - platform_device_put(musb); - -err1: kfree(glue); err0: diff --git a/drivers/usb/musb/davinci.c b/drivers/usb/musb/davinci.c index ed0834e2b72e..1121fd741bf8 100644 --- a/drivers/usb/musb/davinci.c +++ b/drivers/usb/musb/davinci.c @@ -505,14 +505,19 @@ static const struct musb_platform_ops davinci_ops = { .set_vbus = davinci_musb_set_vbus, }; -static u64 davinci_dmamask = DMA_BIT_MASK(32); +static const struct platform_device_info davinci_dev_info = { + .name = "musb-hdrc", + .id = PLATFORM_DEVID_AUTO, + .dma_mask = DMA_BIT_MASK(32), +}; static int davinci_probe(struct platform_device *pdev) { - struct resource musb_resources[2]; + struct resource musb_resources[3]; struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev); struct platform_device *musb; struct davinci_glue *glue; + struct platform_device_info pinfo; struct clk *clk; int ret = -ENOMEM; @@ -523,12 +528,6 @@ static int davinci_probe(struct platform_device *pdev) goto err0; } - musb = platform_device_alloc("musb-hdrc", PLATFORM_DEVID_AUTO); - if (!musb) { - dev_err(&pdev->dev, "failed to allocate musb device\n"); - goto err1; - } - clk = clk_get(&pdev->dev, "usb"); if (IS_ERR(clk)) { dev_err(&pdev->dev, "failed to get clock\n"); @@ -542,12 +541,7 @@ static int davinci_probe(struct platform_device *pdev) goto err4; } - musb->dev.parent = &pdev->dev; - musb->dev.dma_mask = &davinci_dmamask; - musb->dev.coherent_dma_mask = davinci_dmamask; - glue->dev = &pdev->dev; - glue->musb = musb; glue->clk = clk; pdata->platform_ops = &davinci_ops; @@ -567,22 +561,26 @@ static int davinci_probe(struct platform_device *pdev) musb_resources[1].end = pdev->resource[1].end; musb_resources[1].flags = pdev->resource[1].flags; - ret = platform_device_add_resources(musb, musb_resources, - ARRAY_SIZE(musb_resources)); - if (ret) { - dev_err(&pdev->dev, "failed to add resources\n"); - goto err5; - } - - ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); - if (ret) { - dev_err(&pdev->dev, "failed to add platform_data\n"); - goto err5; - } - - ret = platform_device_add(musb); - if (ret) { - dev_err(&pdev->dev, "failed to register musb device\n"); + /* + * For DM6467 3 resources are passed. A placeholder for the 3rd + * resource is always there, so it's safe to always copy it... + */ + musb_resources[2].name = pdev->resource[2].name; + musb_resources[2].start = pdev->resource[2].start; + musb_resources[2].end = pdev->resource[2].end; + musb_resources[2].flags = pdev->resource[2].flags; + + pinfo = davinci_dev_info; + pinfo.parent = &pdev->dev; + pinfo.res = musb_resources; + pinfo.num_res = ARRAY_SIZE(musb_resources); + pinfo.data = pdata; + pinfo.size_data = sizeof(*pdata); + + glue->musb = musb = platform_device_register_full(&pinfo); + if (IS_ERR(musb)) { + ret = PTR_ERR(musb); + dev_err(&pdev->dev, "failed to register musb device: %d\n", ret); goto err5; } @@ -595,9 +593,6 @@ err4: clk_put(clk); err3: - platform_device_put(musb); - -err1: kfree(glue); err0: diff --git a/drivers/usb/musb/musb_am335x.c b/drivers/usb/musb/musb_am335x.c index 41ac5b5b57ce..8be9b02c3cc2 100644 --- a/drivers/usb/musb/musb_am335x.c +++ b/drivers/usb/musb/musb_am335x.c @@ -46,7 +46,7 @@ static struct platform_driver am335x_child_driver = { .remove = am335x_child_remove, .driver = { .name = "am335x-usb-childs", - .of_match_table = of_match_ptr(am335x_child_of_match), + .of_match_table = am335x_child_of_match, }, }; diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index 18e877ffe7b7..4d4499b80449 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -617,7 +617,7 @@ static irqreturn_t musb_stage0_irq(struct musb *musb, u8 int_usb, /* case 3 << MUSB_DEVCTL_VBUS_SHIFT: */ default: s = "VALID"; break; - }; s; }), + } s; }), VBUSERR_RETRY_COUNT - musb->vbuserr_retry, musb->port1_status); @@ -922,6 +922,52 @@ static void musb_generic_disable(struct musb *musb) } /* + * Program the HDRC to start (enable interrupts, dma, etc.). + */ +void musb_start(struct musb *musb) +{ + void __iomem *regs = musb->mregs; + u8 devctl = musb_readb(regs, MUSB_DEVCTL); + + dev_dbg(musb->controller, "<== devctl %02x\n", devctl); + + /* Set INT enable registers, enable interrupts */ + musb->intrtxe = musb->epmask; + musb_writew(regs, MUSB_INTRTXE, musb->intrtxe); + musb->intrrxe = musb->epmask & 0xfffe; + musb_writew(regs, MUSB_INTRRXE, musb->intrrxe); + musb_writeb(regs, MUSB_INTRUSBE, 0xf7); + + musb_writeb(regs, MUSB_TESTMODE, 0); + + /* put into basic highspeed mode and start session */ + musb_writeb(regs, MUSB_POWER, MUSB_POWER_ISOUPDATE + | MUSB_POWER_HSENAB + /* ENSUSPEND wedges tusb */ + /* | MUSB_POWER_ENSUSPEND */ + ); + + musb->is_active = 0; + devctl = musb_readb(regs, MUSB_DEVCTL); + devctl &= ~MUSB_DEVCTL_SESSION; + + /* session started after: + * (a) ID-grounded irq, host mode; + * (b) vbus present/connect IRQ, peripheral mode; + * (c) peripheral initiates, using SRP + */ + if (musb->port_mode != MUSB_PORT_MODE_HOST && + (devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) { + musb->is_active = 1; + } else { + devctl |= MUSB_DEVCTL_SESSION; + } + + musb_platform_enable(musb); + musb_writeb(regs, MUSB_DEVCTL, devctl); +} + +/* * Make the HDRC stop (disable interrupts, etc.); * reversible by musb_start * called on gadget driver unregister @@ -1763,8 +1809,6 @@ static void musb_free(struct musb *musb) disable_irq_wake(musb->nIrq); free_irq(musb->nIrq, musb); } - if (musb->dma_controller) - dma_controller_destroy(musb->dma_controller); musb_host_free(musb); } @@ -1839,13 +1883,21 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl) pm_runtime_get_sync(musb->controller); - if (use_dma && dev->dma_mask) + if (use_dma && dev->dma_mask) { musb->dma_controller = dma_controller_create(musb, musb->mregs); + if (IS_ERR(musb->dma_controller)) { + status = PTR_ERR(musb->dma_controller); + goto fail2_5; + } + } /* be sure interrupts are disabled before connecting ISR */ musb_platform_disable(musb); musb_generic_disable(musb); + /* Init IRQ workqueue before request_irq */ + INIT_WORK(&musb->irq_work, musb_irq_work); + /* setup musb parts of the core (especially endpoints) */ status = musb_core_init(plat->config->multipoint ? MUSB_CONTROLLER_MHDRC @@ -1855,9 +1907,6 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl) setup_timer(&musb->otg_timer, musb_otg_timer_func, (unsigned long) musb); - /* Init IRQ workqueue before request_irq */ - INIT_WORK(&musb->irq_work, musb_irq_work); - /* attach to the IRQ */ if (request_irq(nIrq, musb->isr, 0, dev_name(dev), musb)) { dev_err(dev, "request_irq %d failed!\n", nIrq); @@ -1900,6 +1949,8 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl) if (status < 0) goto fail3; status = musb_gadget_setup(musb); + if (status) + musb_host_cleanup(musb); break; default: dev_err(dev, "unsupported port mode %d\n", musb->port_mode); @@ -1926,10 +1977,13 @@ fail5: fail4: musb_gadget_cleanup(musb); + musb_host_cleanup(musb); fail3: + cancel_work_sync(&musb->irq_work); if (musb->dma_controller) dma_controller_destroy(musb->dma_controller); +fail2_5: pm_runtime_put_sync(musb->controller); fail2: @@ -1986,6 +2040,10 @@ static int musb_remove(struct platform_device *pdev) musb_exit_debugfs(musb); musb_shutdown(pdev); + if (musb->dma_controller) + dma_controller_destroy(musb->dma_controller); + + cancel_work_sync(&musb->irq_work); musb_free(musb); device_init_wakeup(dev, 0); return 0; diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h index 65f3917b4fc5..29f7cd7c7964 100644 --- a/drivers/usb/musb/musb_core.h +++ b/drivers/usb/musb/musb_core.h @@ -46,6 +46,7 @@ #include <linux/usb.h> #include <linux/usb/otg.h> #include <linux/usb/musb.h> +#include <linux/phy/phy.h> struct musb; struct musb_hw_ep; @@ -341,6 +342,7 @@ struct musb { u16 int_tx; struct usb_phy *xceiv; + struct phy *phy; int nIrq; unsigned irq_wake:1; @@ -503,6 +505,7 @@ static inline void musb_configure_ep0(struct musb *musb) extern const char musb_driver_name[]; extern void musb_stop(struct musb *musb); +extern void musb_start(struct musb *musb); extern void musb_write_fifo(struct musb_hw_ep *ep, u16 len, const u8 *src); extern void musb_read_fifo(struct musb_hw_ep *ep, u16 len, u8 *dst); diff --git a/drivers/usb/musb/musb_cppi41.c b/drivers/usb/musb/musb_cppi41.c index ae959746f77f..a12bd30401e0 100644 --- a/drivers/usb/musb/musb_cppi41.c +++ b/drivers/usb/musb/musb_cppi41.c @@ -38,6 +38,7 @@ struct cppi41_dma_channel { u32 prog_len; u32 transferred; u32 packet_sz; + struct list_head tx_check; }; #define MUSB_DMA_NUM_CHANNELS 15 @@ -47,6 +48,8 @@ struct cppi41_dma_controller { struct cppi41_dma_channel rx_channel[MUSB_DMA_NUM_CHANNELS]; struct cppi41_dma_channel tx_channel[MUSB_DMA_NUM_CHANNELS]; struct musb *musb; + struct hrtimer early_tx; + struct list_head early_tx_list; u32 rx_mode; u32 tx_mode; u32 auto_req; @@ -96,31 +99,27 @@ static void update_rx_toggle(struct cppi41_dma_channel *cppi41_channel) cppi41_channel->usb_toggle = toggle; } -static void cppi41_dma_callback(void *private_data) +static bool musb_is_tx_fifo_empty(struct musb_hw_ep *hw_ep) { - struct dma_channel *channel = private_data; - struct cppi41_dma_channel *cppi41_channel = channel->private_data; - struct musb_hw_ep *hw_ep = cppi41_channel->hw_ep; - struct musb *musb = hw_ep->musb; - unsigned long flags; - struct dma_tx_state txstate; - u32 transferred; - - spin_lock_irqsave(&musb->lock, flags); + u8 epnum = hw_ep->epnum; + struct musb *musb = hw_ep->musb; + void __iomem *epio = musb->endpoints[epnum].regs; + u16 csr; - dmaengine_tx_status(cppi41_channel->dc, cppi41_channel->cookie, - &txstate); - transferred = cppi41_channel->prog_len - txstate.residue; - cppi41_channel->transferred += transferred; + csr = musb_readw(epio, MUSB_TXCSR); + if (csr & MUSB_TXCSR_TXPKTRDY) + return false; + return true; +} - dev_dbg(musb->controller, "DMA transfer done on hw_ep=%d bytes=%d/%d\n", - hw_ep->epnum, cppi41_channel->transferred, - cppi41_channel->total_len); +static void cppi41_dma_callback(void *private_data); - update_rx_toggle(cppi41_channel); +static void cppi41_trans_done(struct cppi41_dma_channel *cppi41_channel) +{ + struct musb_hw_ep *hw_ep = cppi41_channel->hw_ep; + struct musb *musb = hw_ep->musb; - if (cppi41_channel->transferred == cppi41_channel->total_len || - transferred < cppi41_channel->packet_sz) { + if (!cppi41_channel->prog_len) { /* done, complete */ cppi41_channel->channel.actual_len = @@ -150,13 +149,11 @@ static void cppi41_dma_callback(void *private_data) remain_bytes, direction, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); - if (WARN_ON(!dma_desc)) { - spin_unlock_irqrestore(&musb->lock, flags); + if (WARN_ON(!dma_desc)) return; - } dma_desc->callback = cppi41_dma_callback; - dma_desc->callback_param = channel; + dma_desc->callback_param = &cppi41_channel->channel; cppi41_channel->cookie = dma_desc->tx_submit(dma_desc); dma_async_issue_pending(dc); @@ -166,6 +163,117 @@ static void cppi41_dma_callback(void *private_data) musb_writew(epio, MUSB_RXCSR, csr); } } +} + +static enum hrtimer_restart cppi41_recheck_tx_req(struct hrtimer *timer) +{ + struct cppi41_dma_controller *controller; + struct cppi41_dma_channel *cppi41_channel, *n; + struct musb *musb; + unsigned long flags; + enum hrtimer_restart ret = HRTIMER_NORESTART; + + controller = container_of(timer, struct cppi41_dma_controller, + early_tx); + musb = controller->musb; + + spin_lock_irqsave(&musb->lock, flags); + list_for_each_entry_safe(cppi41_channel, n, &controller->early_tx_list, + tx_check) { + bool empty; + struct musb_hw_ep *hw_ep = cppi41_channel->hw_ep; + + empty = musb_is_tx_fifo_empty(hw_ep); + if (empty) { + list_del_init(&cppi41_channel->tx_check); + cppi41_trans_done(cppi41_channel); + } + } + + if (!list_empty(&controller->early_tx_list)) { + ret = HRTIMER_RESTART; + hrtimer_forward_now(&controller->early_tx, + ktime_set(0, 150 * NSEC_PER_USEC)); + } + + spin_unlock_irqrestore(&musb->lock, flags); + return ret; +} + +static void cppi41_dma_callback(void *private_data) +{ + struct dma_channel *channel = private_data; + struct cppi41_dma_channel *cppi41_channel = channel->private_data; + struct musb_hw_ep *hw_ep = cppi41_channel->hw_ep; + struct musb *musb = hw_ep->musb; + unsigned long flags; + struct dma_tx_state txstate; + u32 transferred; + bool empty; + + spin_lock_irqsave(&musb->lock, flags); + + dmaengine_tx_status(cppi41_channel->dc, cppi41_channel->cookie, + &txstate); + transferred = cppi41_channel->prog_len - txstate.residue; + cppi41_channel->transferred += transferred; + + dev_dbg(musb->controller, "DMA transfer done on hw_ep=%d bytes=%d/%d\n", + hw_ep->epnum, cppi41_channel->transferred, + cppi41_channel->total_len); + + update_rx_toggle(cppi41_channel); + + if (cppi41_channel->transferred == cppi41_channel->total_len || + transferred < cppi41_channel->packet_sz) + cppi41_channel->prog_len = 0; + + empty = musb_is_tx_fifo_empty(hw_ep); + if (empty) { + cppi41_trans_done(cppi41_channel); + } else { + struct cppi41_dma_controller *controller; + /* + * On AM335x it has been observed that the TX interrupt fires + * too early that means the TXFIFO is not yet empty but the DMA + * engine says that it is done with the transfer. We don't + * receive a FIFO empty interrupt so the only thing we can do is + * to poll for the bit. On HS it usually takes 2us, on FS around + * 110us - 150us depending on the transfer size. + * We spin on HS (no longer than than 25us and setup a timer on + * FS to check for the bit and complete the transfer. + */ + controller = cppi41_channel->controller; + + if (musb->g.speed == USB_SPEED_HIGH) { + unsigned wait = 25; + + do { + empty = musb_is_tx_fifo_empty(hw_ep); + if (empty) + break; + wait--; + if (!wait) + break; + udelay(1); + } while (1); + + empty = musb_is_tx_fifo_empty(hw_ep); + if (empty) { + cppi41_trans_done(cppi41_channel); + goto out; + } + } + list_add_tail(&cppi41_channel->tx_check, + &controller->early_tx_list); + if (!hrtimer_active(&controller->early_tx)) { + hrtimer_start_range_ns(&controller->early_tx, + ktime_set(0, 140 * NSEC_PER_USEC), + 40 * NSEC_PER_USEC, + HRTIMER_MODE_REL); + } + } +out: spin_unlock_irqrestore(&musb->lock, flags); } @@ -364,6 +472,8 @@ static int cppi41_is_compatible(struct dma_channel *channel, u16 maxpacket, WARN_ON(1); return 1; } + if (cppi41_channel->hw_ep->ep_in.type != USB_ENDPOINT_XFER_BULK) + return 0; if (cppi41_channel->is_tx) return 1; /* AM335x Advisory 1.0.13. No workaround for device RX mode */ @@ -388,6 +498,7 @@ static int cppi41_dma_channel_abort(struct dma_channel *channel) if (cppi41_channel->channel.status == MUSB_DMA_STATUS_FREE) return 0; + list_del_init(&cppi41_channel->tx_check); if (is_tx) { csr = musb_readw(epio, MUSB_TXCSR); csr &= ~MUSB_TXCSR_DMAENAB; @@ -484,6 +595,7 @@ static int cppi41_dma_controller_start(struct cppi41_dma_controller *controller) if (ret) goto err; + ret = -EINVAL; if (port > MUSB_DMA_NUM_CHANNELS || !port) goto err; if (is_tx) @@ -494,6 +606,7 @@ static int cppi41_dma_controller_start(struct cppi41_dma_controller *controller) cppi41_channel->controller = controller; cppi41_channel->port_num = port; cppi41_channel->is_tx = is_tx; + INIT_LIST_HEAD(&cppi41_channel->tx_check); musb_dma = &cppi41_channel->channel; musb_dma->private_data = cppi41_channel; @@ -503,6 +616,7 @@ static int cppi41_dma_controller_start(struct cppi41_dma_controller *controller) dc = dma_request_slave_channel(dev, str); if (!dc) { dev_err(dev, "Falied to request %s.\n", str); + ret = -EPROBE_DEFER; goto err; } cppi41_channel->dc = dc; @@ -510,7 +624,7 @@ static int cppi41_dma_controller_start(struct cppi41_dma_controller *controller) return 0; err: cppi41_release_all_dma_chans(controller); - return -EINVAL; + return ret; } void dma_controller_destroy(struct dma_controller *c) @@ -518,6 +632,7 @@ void dma_controller_destroy(struct dma_controller *c) struct cppi41_dma_controller *controller = container_of(c, struct cppi41_dma_controller, controller); + hrtimer_cancel(&controller->early_tx); cppi41_dma_controller_stop(controller); kfree(controller); } @@ -526,7 +641,7 @@ struct dma_controller *dma_controller_create(struct musb *musb, void __iomem *base) { struct cppi41_dma_controller *controller; - int ret; + int ret = 0; if (!musb->controller->of_node) { dev_err(musb->controller, "Need DT for the DMA engine.\n"); @@ -537,6 +652,9 @@ struct dma_controller *dma_controller_create(struct musb *musb, if (!controller) goto kzalloc_fail; + hrtimer_init(&controller->early_tx, CLOCK_MONOTONIC, HRTIMER_MODE_REL); + controller->early_tx.function = cppi41_recheck_tx_req; + INIT_LIST_HEAD(&controller->early_tx_list); controller->musb = musb; controller->controller.channel_alloc = cppi41_dma_channel_allocate; @@ -553,5 +671,7 @@ struct dma_controller *dma_controller_create(struct musb *musb, plat_get_fail: kfree(controller); kzalloc_fail: + if (ret == -EPROBE_DEFER) + return ERR_PTR(ret); return NULL; } diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c index 4047cbb91bac..1901f6fe5807 100644 --- a/drivers/usb/musb/musb_dsps.c +++ b/drivers/usb/musb/musb_dsps.c @@ -121,6 +121,43 @@ struct dsps_glue { unsigned long last_timer; /* last timer data for each instance */ }; +static void dsps_musb_try_idle(struct musb *musb, unsigned long timeout) +{ + struct device *dev = musb->controller; + struct dsps_glue *glue = dev_get_drvdata(dev->parent); + + if (timeout == 0) + timeout = jiffies + msecs_to_jiffies(3); + + /* Never idle if active, or when VBUS timeout is not set as host */ + if (musb->is_active || (musb->a_wait_bcon == 0 && + musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) { + dev_dbg(musb->controller, "%s active, deleting timer\n", + usb_otg_state_string(musb->xceiv->state)); + del_timer(&glue->timer); + glue->last_timer = jiffies; + return; + } + if (musb->port_mode != MUSB_PORT_MODE_DUAL_ROLE) + return; + + if (!musb->g.dev.driver) + return; + + if (time_after(glue->last_timer, timeout) && + timer_pending(&glue->timer)) { + dev_dbg(musb->controller, + "Longer idle timer already pending, ignoring...\n"); + return; + } + glue->last_timer = timeout; + + dev_dbg(musb->controller, "%s inactive, starting idle timer for %u ms\n", + usb_otg_state_string(musb->xceiv->state), + jiffies_to_msecs(timeout - jiffies)); + mod_timer(&glue->timer, timeout); +} + /** * dsps_musb_enable - enable interrupts */ @@ -143,6 +180,7 @@ static void dsps_musb_enable(struct musb *musb) /* Force the DRVVBUS IRQ so we can start polling for ID change. */ dsps_writel(reg_base, wrp->coreintr_set, (1 << wrp->drvvbus) << wrp->usb_shift); + dsps_musb_try_idle(musb, 0); } /** @@ -171,6 +209,7 @@ static void otg_timer(unsigned long _musb) const struct dsps_musb_wrapper *wrp = glue->wrp; u8 devctl; unsigned long flags; + int skip_session = 0; /* * We poll because DSPS IP's won't expose several OTG-critical @@ -183,10 +222,12 @@ static void otg_timer(unsigned long _musb) spin_lock_irqsave(&musb->lock, flags); switch (musb->xceiv->state) { case OTG_STATE_A_WAIT_BCON: - devctl &= ~MUSB_DEVCTL_SESSION; - dsps_writeb(musb->mregs, MUSB_DEVCTL, devctl); + dsps_writeb(musb->mregs, MUSB_DEVCTL, 0); + skip_session = 1; + /* fall */ - devctl = dsps_readb(musb->mregs, MUSB_DEVCTL); + case OTG_STATE_A_IDLE: + case OTG_STATE_B_IDLE: if (devctl & MUSB_DEVCTL_BDEVICE) { musb->xceiv->state = OTG_STATE_B_IDLE; MUSB_DEV_MODE(musb); @@ -194,60 +235,21 @@ static void otg_timer(unsigned long _musb) musb->xceiv->state = OTG_STATE_A_IDLE; MUSB_HST_MODE(musb); } + if (!(devctl & MUSB_DEVCTL_SESSION) && !skip_session) + dsps_writeb(mregs, MUSB_DEVCTL, MUSB_DEVCTL_SESSION); + mod_timer(&glue->timer, jiffies + wrp->poll_seconds * HZ); break; case OTG_STATE_A_WAIT_VFALL: musb->xceiv->state = OTG_STATE_A_WAIT_VRISE; dsps_writel(musb->ctrl_base, wrp->coreintr_set, MUSB_INTR_VBUSERROR << wrp->usb_shift); break; - case OTG_STATE_B_IDLE: - devctl = dsps_readb(mregs, MUSB_DEVCTL); - if (devctl & MUSB_DEVCTL_BDEVICE) - mod_timer(&glue->timer, - jiffies + wrp->poll_seconds * HZ); - else - musb->xceiv->state = OTG_STATE_A_IDLE; - break; default: break; } spin_unlock_irqrestore(&musb->lock, flags); } -static void dsps_musb_try_idle(struct musb *musb, unsigned long timeout) -{ - struct device *dev = musb->controller; - struct dsps_glue *glue = dev_get_drvdata(dev->parent); - - if (timeout == 0) - timeout = jiffies + msecs_to_jiffies(3); - - /* Never idle if active, or when VBUS timeout is not set as host */ - if (musb->is_active || (musb->a_wait_bcon == 0 && - musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) { - dev_dbg(musb->controller, "%s active, deleting timer\n", - usb_otg_state_string(musb->xceiv->state)); - del_timer(&glue->timer); - glue->last_timer = jiffies; - return; - } - if (musb->port_mode == MUSB_PORT_MODE_HOST) - return; - - if (time_after(glue->last_timer, timeout) && - timer_pending(&glue->timer)) { - dev_dbg(musb->controller, - "Longer idle timer already pending, ignoring...\n"); - return; - } - glue->last_timer = timeout; - - dev_dbg(musb->controller, "%s inactive, starting idle timer for %u ms\n", - usb_otg_state_string(musb->xceiv->state), - jiffies_to_msecs(timeout - jiffies)); - mod_timer(&glue->timer, timeout); -} - static irqreturn_t dsps_interrupt(int irq, void *hci) { struct musb *musb = hci; @@ -443,7 +445,7 @@ static int get_musb_port_mode(struct device *dev) case USB_DR_MODE_OTG: default: return MUSB_PORT_MODE_DUAL_ROLE; - }; + } } static int dsps_create_musb_pdev(struct dsps_glue *glue, @@ -535,6 +537,9 @@ static int dsps_probe(struct platform_device *pdev) struct dsps_glue *glue; int ret; + if (!strcmp(pdev->name, "musb-hdrc")) + return -ENODEV; + match = of_match_node(musb_dsps_of_match, pdev->dev.of_node); if (!match) { dev_err(&pdev->dev, "fail to get matching of_match struct\n"); @@ -628,7 +633,7 @@ static struct platform_driver dsps_usbss_driver = { .remove = dsps_remove, .driver = { .name = "musb-dsps", - .of_match_table = of_match_ptr(musb_dsps_of_match), + .of_match_table = musb_dsps_of_match, }, }; diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c index 9a08679d204d..32fb057c03f5 100644 --- a/drivers/usb/musb/musb_gadget.c +++ b/drivers/usb/musb/musb_gadget.c @@ -1121,7 +1121,7 @@ static int musb_gadget_enable(struct usb_ep *ep, case USB_ENDPOINT_XFER_BULK: s = "bulk"; break; case USB_ENDPOINT_XFER_INT: s = "int"; break; default: s = "iso"; break; - }; s; }), + } s; }), musb_ep->is_in ? "IN" : "OUT", musb_ep->dma ? "dma, " : "", musb_ep->packet_sz); @@ -1790,9 +1790,17 @@ int musb_gadget_setup(struct musb *musb) musb->g.max_speed = USB_SPEED_HIGH; musb->g.speed = USB_SPEED_UNKNOWN; + MUSB_DEV_MODE(musb); + musb->xceiv->otg->default_a = 0; + musb->xceiv->state = OTG_STATE_B_IDLE; + /* this "gadget" abstracts/virtualizes the controller */ musb->g.name = musb_driver_name; +#if IS_ENABLED(CONFIG_USB_MUSB_DUAL_ROLE) musb->g.is_otg = 1; +#elif IS_ENABLED(CONFIG_USB_MUSB_GADGET) + musb->g.is_otg = 0; +#endif musb_g_init_endpoints(musb); @@ -1855,6 +1863,8 @@ static int musb_gadget_start(struct usb_gadget *g, musb->xceiv->state = OTG_STATE_B_IDLE; spin_unlock_irqrestore(&musb->lock, flags); + musb_start(musb); + /* REVISIT: funcall to other code, which also * handles power budgeting ... this way also * ensures HdrcStart is indirectly called. diff --git a/drivers/usb/musb/musb_host.c b/drivers/usb/musb/musb_host.c index 9a2b8c85f19a..6582a20bec05 100644 --- a/drivers/usb/musb/musb_host.c +++ b/drivers/usb/musb/musb_host.c @@ -253,7 +253,7 @@ musb_start_urb(struct musb *musb, int is_in, struct musb_qh *qh) case USB_ENDPOINT_XFER_BULK: s = "-bulk"; break; case USB_ENDPOINT_XFER_ISOC: s = "-iso"; break; default: s = "-intr"; break; - }; s; }), + } s; }), epnum, buf + offset, len); /* Configure endpoint */ diff --git a/drivers/usb/musb/musb_virthub.c b/drivers/usb/musb/musb_virthub.c index a523950c2b32..9af6bba5eac9 100644 --- a/drivers/usb/musb/musb_virthub.c +++ b/drivers/usb/musb/musb_virthub.c @@ -44,52 +44,6 @@ #include "musb_core.h" -/* -* Program the HDRC to start (enable interrupts, dma, etc.). -*/ -static void musb_start(struct musb *musb) -{ - void __iomem *regs = musb->mregs; - u8 devctl = musb_readb(regs, MUSB_DEVCTL); - - dev_dbg(musb->controller, "<== devctl %02x\n", devctl); - - /* Set INT enable registers, enable interrupts */ - musb->intrtxe = musb->epmask; - musb_writew(regs, MUSB_INTRTXE, musb->intrtxe); - musb->intrrxe = musb->epmask & 0xfffe; - musb_writew(regs, MUSB_INTRRXE, musb->intrrxe); - musb_writeb(regs, MUSB_INTRUSBE, 0xf7); - - musb_writeb(regs, MUSB_TESTMODE, 0); - - /* put into basic highspeed mode and start session */ - musb_writeb(regs, MUSB_POWER, MUSB_POWER_ISOUPDATE - | MUSB_POWER_HSENAB - /* ENSUSPEND wedges tusb */ - /* | MUSB_POWER_ENSUSPEND */ - ); - - musb->is_active = 0; - devctl = musb_readb(regs, MUSB_DEVCTL); - devctl &= ~MUSB_DEVCTL_SESSION; - - /* session started after: - * (a) ID-grounded irq, host mode; - * (b) vbus present/connect IRQ, peripheral mode; - * (c) peripheral initiates, using SRP - */ - if (musb->port_mode != MUSB_PORT_MODE_HOST && - (devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) { - musb->is_active = 1; - } else { - devctl |= MUSB_DEVCTL_SESSION; - } - - musb_platform_enable(musb); - musb_writeb(regs, MUSB_DEVCTL, devctl); -} - static void musb_port_suspend(struct musb *musb, bool do_suspend) { struct usb_otg *otg = musb->xceiv->otg; @@ -266,6 +220,23 @@ int musb_hub_status_data(struct usb_hcd *hcd, char *buf) return retval; } +static int musb_has_gadget(struct musb *musb) +{ + /* + * In host-only mode we start a connection right away. In OTG mode + * we have to wait until we loaded a gadget. We don't really need a + * gadget if we operate as a host but we should not start a session + * as a device without a gadget or else we explode. + */ +#ifdef CONFIG_USB_MUSB_HOST + return 1; +#else + if (musb->port_mode == MUSB_PORT_MODE_HOST) + return 1; + return musb->g.dev.driver != NULL; +#endif +} + int musb_hub_control( struct usb_hcd *hcd, u16 typeReq, @@ -408,7 +379,7 @@ int musb_hub_control( * initialization logic, e.g. for OTG, or change any * logic relating to VBUS power-up. */ - if (!hcd->self.is_b_host) + if (!hcd->self.is_b_host && musb_has_gadget(musb)) musb_start(musb); break; case USB_PORT_FEAT_RESET: diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c index 59d2245db1c8..2a408cdaf7b2 100644 --- a/drivers/usb/musb/omap2430.c +++ b/drivers/usb/musb/omap2430.c @@ -38,6 +38,7 @@ #include <linux/delay.h> #include <linux/usb/musb-omap.h> #include <linux/usb/omap_control_usb.h> +#include <linux/of_platform.h> #include "musb_core.h" #include "omap2430.h" @@ -305,6 +306,9 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue) default: dev_dbg(dev, "ID float\n"); } + + atomic_notifier_call_chain(&musb->xceiv->notifier, + musb->xceiv->last_event, NULL); } @@ -348,11 +352,21 @@ static int omap2430_musb_init(struct musb *musb) * up through ULPI. TWL4030-family PMICs include one, * which needs a driver, drivers aren't always needed. */ - if (dev->parent->of_node) + if (dev->parent->of_node) { + musb->phy = devm_phy_get(dev->parent, "usb2-phy"); + + /* We can't totally remove musb->xceiv as of now because + * musb core uses xceiv.state and xceiv.otg. Once we have + * a separate state machine to handle otg, these can be moved + * out of xceiv and then we can start using the generic PHY + * framework + */ musb->xceiv = devm_usb_get_phy_by_phandle(dev->parent, "usb-phy", 0); - else + } else { musb->xceiv = devm_usb_get_phy_dev(dev, 0); + musb->phy = devm_phy_get(dev, "usb"); + } if (IS_ERR(musb->xceiv)) { status = PTR_ERR(musb->xceiv); @@ -364,6 +378,10 @@ static int omap2430_musb_init(struct musb *musb) return -EPROBE_DEFER; } + if (IS_ERR(musb->phy)) { + pr_err("HS USB OTG: no PHY configured\n"); + return PTR_ERR(musb->phy); + } musb->isr = omap2430_musb_interrupt; status = pm_runtime_get_sync(dev); @@ -397,7 +415,7 @@ static int omap2430_musb_init(struct musb *musb) if (glue->status != OMAP_MUSB_UNKNOWN) omap_musb_set_mailbox(glue); - usb_phy_init(musb->xceiv); + phy_init(musb->phy); pm_runtime_put_noidle(musb->controller); return 0; @@ -460,6 +478,7 @@ static int omap2430_musb_exit(struct musb *musb) del_timer_sync(&musb_idle_timer); omap2430_low_level_exit(musb); + phy_exit(musb->phy); return 0; } @@ -509,8 +528,12 @@ static int omap2430_probe(struct platform_device *pdev) glue->dev = &pdev->dev; glue->musb = musb; glue->status = OMAP_MUSB_UNKNOWN; + glue->control_otghs = ERR_PTR(-ENODEV); if (np) { + struct device_node *control_node; + struct platform_device *control_pdev; + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); if (!pdata) { dev_err(&pdev->dev, @@ -539,22 +562,20 @@ static int omap2430_probe(struct platform_device *pdev) of_property_read_u32(np, "ram-bits", (u32 *)&config->ram_bits); of_property_read_u32(np, "power", (u32 *)&pdata->power); config->multipoint = of_property_read_bool(np, "multipoint"); - pdata->has_mailbox = of_property_read_bool(np, - "ti,has-mailbox"); pdata->board_data = data; pdata->config = config; - } - if (pdata->has_mailbox) { - glue->control_otghs = omap_get_control_dev(); - if (IS_ERR(glue->control_otghs)) { - dev_vdbg(&pdev->dev, "Failed to get control device\n"); - ret = PTR_ERR(glue->control_otghs); - goto err2; + control_node = of_parse_phandle(np, "ctrl-module", 0); + if (control_node) { + control_pdev = of_find_device_by_node(control_node); + if (!control_pdev) { + dev_err(&pdev->dev, "Failed to get control device\n"); + ret = -EINVAL; + goto err2; + } + glue->control_otghs = &control_pdev->dev; } - } else { - glue->control_otghs = ERR_PTR(-ENODEV); } pdata->platform_ops = &omap2430_ops; @@ -638,7 +659,7 @@ static int omap2430_runtime_suspend(struct device *dev) OTG_INTERFSEL); omap2430_low_level_exit(musb); - usb_phy_set_suspend(musb->xceiv, 1); + phy_power_off(musb->phy); } return 0; @@ -653,8 +674,7 @@ static int omap2430_runtime_resume(struct device *dev) omap2430_low_level_init(musb); musb_writel(musb->mregs, OTG_INTERFSEL, musb->context.otg_interfsel); - - usb_phy_set_suspend(musb->xceiv, 0); + phy_power_on(musb->phy); } return 0; diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c index b3b3ed723882..4432314d70ee 100644 --- a/drivers/usb/musb/tusb6010.c +++ b/drivers/usb/musb/tusb6010.c @@ -1152,7 +1152,11 @@ static const struct musb_platform_ops tusb_ops = { .set_vbus = tusb_musb_set_vbus, }; -static u64 tusb_dmamask = DMA_BIT_MASK(32); +static const struct platform_device_info tusb_dev_info = { + .name = "musb-hdrc", + .id = PLATFORM_DEVID_AUTO, + .dma_mask = DMA_BIT_MASK(32), +}; static int tusb_probe(struct platform_device *pdev) { @@ -1160,7 +1164,7 @@ static int tusb_probe(struct platform_device *pdev) struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev); struct platform_device *musb; struct tusb6010_glue *glue; - + struct platform_device_info pinfo; int ret = -ENOMEM; glue = kzalloc(sizeof(*glue), GFP_KERNEL); @@ -1169,18 +1173,7 @@ static int tusb_probe(struct platform_device *pdev) goto err0; } - musb = platform_device_alloc("musb-hdrc", PLATFORM_DEVID_AUTO); - if (!musb) { - dev_err(&pdev->dev, "failed to allocate musb device\n"); - goto err1; - } - - musb->dev.parent = &pdev->dev; - musb->dev.dma_mask = &tusb_dmamask; - musb->dev.coherent_dma_mask = tusb_dmamask; - glue->dev = &pdev->dev; - glue->musb = musb; pdata->platform_ops = &tusb_ops; @@ -1204,31 +1197,23 @@ static int tusb_probe(struct platform_device *pdev) musb_resources[2].end = pdev->resource[2].end; musb_resources[2].flags = pdev->resource[2].flags; - ret = platform_device_add_resources(musb, musb_resources, - ARRAY_SIZE(musb_resources)); - if (ret) { - dev_err(&pdev->dev, "failed to add resources\n"); - goto err3; - } - - ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); - if (ret) { - dev_err(&pdev->dev, "failed to add platform_data\n"); - goto err3; - } - - ret = platform_device_add(musb); - if (ret) { - dev_err(&pdev->dev, "failed to register musb device\n"); + pinfo = tusb_dev_info; + pinfo.parent = &pdev->dev; + pinfo.res = musb_resources; + pinfo.num_res = ARRAY_SIZE(musb_resources); + pinfo.data = pdata; + pinfo.size_data = sizeof(*pdata); + + glue->musb = musb = platform_device_register_full(&pinfo); + if (IS_ERR(musb)) { + ret = PTR_ERR(musb); + dev_err(&pdev->dev, "failed to register musb device: %d\n", ret); goto err3; } return 0; err3: - platform_device_put(musb); - -err1: kfree(glue); err0: diff --git a/drivers/usb/musb/ux500.c b/drivers/usb/musb/ux500.c index 59256b12f746..122446bf1664 100644 --- a/drivers/usb/musb/ux500.c +++ b/drivers/usb/musb/ux500.c @@ -259,7 +259,7 @@ static int ux500_probe(struct platform_device *pdev) goto err1; } - clk = clk_get(&pdev->dev, "usb"); + clk = clk_get(&pdev->dev, NULL); if (IS_ERR(clk)) { dev_err(&pdev->dev, "failed to get clock\n"); ret = PTR_ERR(clk); @@ -376,17 +376,10 @@ static int ux500_resume(struct device *dev) return 0; } - -static const struct dev_pm_ops ux500_pm_ops = { - .suspend = ux500_suspend, - .resume = ux500_resume, -}; - -#define DEV_PM_OPS (&ux500_pm_ops) -#else -#define DEV_PM_OPS NULL #endif +static SIMPLE_DEV_PM_OPS(ux500_pm_ops, ux500_suspend, ux500_resume); + static const struct of_device_id ux500_match[] = { { .compatible = "stericsson,db8500-musb", }, {} @@ -397,7 +390,7 @@ static struct platform_driver ux500_driver = { .remove = ux500_remove, .driver = { .name = "musb-ux500", - .pm = DEV_PM_OPS, + .pm = &ux500_pm_ops, .of_match_table = ux500_match, }, }; |