diff options
Diffstat (limited to 'drivers/tty/serial')
| -rw-r--r-- | drivers/tty/serial/Kconfig | 149 | ||||
| -rw-r--r-- | drivers/tty/serial/Makefile | 2 | ||||
| -rw-r--r-- | drivers/tty/serial/bfin_sport_uart.c | 937 | ||||
| -rw-r--r-- | drivers/tty/serial/bfin_sport_uart.h | 86 | ||||
| -rw-r--r-- | drivers/tty/serial/bfin_uart.c | 1551 |
5 files changed, 0 insertions, 2725 deletions
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index f6e09326042d..031552eb3f65 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -498,92 +498,6 @@ config SERIAL_SA1100_CONSOLE your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) -config SERIAL_BFIN - tristate "Blackfin serial port support" - depends on BLACKFIN - select SERIAL_CORE - select SERIAL_BFIN_UART0 if (BF531 || BF532 || BF533 || BF561) - help - Add support for the built-in UARTs on the Blackfin. - - To compile this driver as a module, choose M here: the - module is named bfin_uart.ko. - -config SERIAL_BFIN_CONSOLE - bool "Console on Blackfin serial port" - depends on SERIAL_BFIN=y - select SERIAL_CORE_CONSOLE - -choice - prompt "UART Mode" - depends on SERIAL_BFIN - default SERIAL_BFIN_DMA - help - This driver supports the built-in serial ports of the Blackfin family - of CPUs - -config SERIAL_BFIN_DMA - bool "DMA mode" - depends on !DMA_UNCACHED_NONE && KGDB_SERIAL_CONSOLE=n - help - This driver works under DMA mode. If this option is selected, the - blackfin simple dma driver is also enabled. - -config SERIAL_BFIN_PIO - bool "PIO mode" - help - This driver works under PIO mode. - -endchoice - -config SERIAL_BFIN_UART0 - bool "Enable UART0" - depends on SERIAL_BFIN - help - Enable UART0 - -config BFIN_UART0_CTSRTS - bool "Enable UART0 hardware flow control" - depends on SERIAL_BFIN_UART0 - help - Enable hardware flow control in the driver. - -config SERIAL_BFIN_UART1 - bool "Enable UART1" - depends on SERIAL_BFIN && (!BF531 && !BF532 && !BF533 && !BF561) - help - Enable UART1 - -config BFIN_UART1_CTSRTS - bool "Enable UART1 hardware flow control" - depends on SERIAL_BFIN_UART1 - help - Enable hardware flow control in the driver. - -config SERIAL_BFIN_UART2 - bool "Enable UART2" - depends on SERIAL_BFIN && (BF54x || BF538 || BF539) - help - Enable UART2 - -config BFIN_UART2_CTSRTS - bool "Enable UART2 hardware flow control" - depends on SERIAL_BFIN_UART2 - help - Enable hardware flow control in the driver. - -config SERIAL_BFIN_UART3 - bool "Enable UART3" - depends on SERIAL_BFIN && (BF54x) - help - Enable UART3 - -config BFIN_UART3_CTSRTS - bool "Enable UART3 hardware flow control" - depends on SERIAL_BFIN_UART3 - help - Enable hardware flow control in the driver. - config SERIAL_IMX tristate "IMX serial port support" depends on HAS_DMA @@ -1231,69 +1145,6 @@ config SERIAL_SC16IS7XX_SPI This is additional support to exsisting driver. You must select at least one bus for the driver to be built. -config SERIAL_BFIN_SPORT - tristate "Blackfin SPORT emulate UART" - depends on BLACKFIN - select SERIAL_CORE - help - Enable SPORT emulate UART on Blackfin series. - - To compile this driver as a module, choose M here: the - module will be called bfin_sport_uart. - -config SERIAL_BFIN_SPORT_CONSOLE - bool "Console on Blackfin sport emulated uart" - depends on SERIAL_BFIN_SPORT=y - select SERIAL_CORE_CONSOLE - -config SERIAL_BFIN_SPORT0_UART - bool "Enable UART over SPORT0" - depends on SERIAL_BFIN_SPORT && !(BF542 || BF544) - help - Enable UART over SPORT0 - -config SERIAL_BFIN_SPORT0_UART_CTSRTS - bool "Enable UART over SPORT0 hardware flow control" - depends on SERIAL_BFIN_SPORT0_UART - help - Enable hardware flow control in the driver. - -config SERIAL_BFIN_SPORT1_UART - bool "Enable UART over SPORT1" - depends on SERIAL_BFIN_SPORT - help - Enable UART over SPORT1 - -config SERIAL_BFIN_SPORT1_UART_CTSRTS - bool "Enable UART over SPORT1 hardware flow control" - depends on SERIAL_BFIN_SPORT1_UART - help - Enable hardware flow control in the driver. - -config SERIAL_BFIN_SPORT2_UART - bool "Enable UART over SPORT2" - depends on SERIAL_BFIN_SPORT && (BF54x || BF538 || BF539) - help - Enable UART over SPORT2 - -config SERIAL_BFIN_SPORT2_UART_CTSRTS - bool "Enable UART over SPORT2 hardware flow control" - depends on SERIAL_BFIN_SPORT2_UART - help - Enable hardware flow control in the driver. - -config SERIAL_BFIN_SPORT3_UART - bool "Enable UART over SPORT3" - depends on SERIAL_BFIN_SPORT && (BF54x || BF538 || BF539) - help - Enable UART over SPORT3 - -config SERIAL_BFIN_SPORT3_UART_CTSRTS - bool "Enable UART over SPORT3 hardware flow control" - depends on SERIAL_BFIN_SPORT3_UART - help - Enable hardware flow control in the driver. - config SERIAL_TIMBERDALE tristate "Support for timberdale UART" select SERIAL_CORE diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile index c21835dc16b2..a9242484e821 100644 --- a/drivers/tty/serial/Makefile +++ b/drivers/tty/serial/Makefile @@ -29,8 +29,6 @@ obj-$(CONFIG_SERIAL_PXA_NON8250) += pxa.o obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o obj-$(CONFIG_SERIAL_SA1100) += sa1100.o obj-$(CONFIG_SERIAL_BCM63XX) += bcm63xx_uart.o -obj-$(CONFIG_SERIAL_BFIN) += bfin_uart.o -obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o obj-$(CONFIG_SERIAL_MAX3100) += max3100.o obj-$(CONFIG_SERIAL_MAX310X) += max310x.o diff --git a/drivers/tty/serial/bfin_sport_uart.c b/drivers/tty/serial/bfin_sport_uart.c deleted file mode 100644 index 4ccca5d22f4f..000000000000 --- a/drivers/tty/serial/bfin_sport_uart.c +++ /dev/null @@ -1,937 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Blackfin On-Chip Sport Emulated UART Driver - * - * Copyright 2006-2009 Analog Devices Inc. - * - * Enter bugs at http://blackfin.uclinux.org/ - */ - -/* - * This driver and the hardware supported are in term of EE-191 of ADI. - * http://www.analog.com/static/imported-files/application_notes/EE191.pdf - * This application note describe how to implement a UART on a Sharc DSP, - * but this driver is implemented on Blackfin Processor. - * Transmit Frame Sync is not used by this driver to transfer data out. - */ - -/* #define DEBUG */ - -#define DRV_NAME "bfin-sport-uart" -#define DEVICE_NAME "ttySS" -#define pr_fmt(fmt) DRV_NAME ": " fmt - -#include <linux/module.h> -#include <linux/ioport.h> -#include <linux/io.h> -#include <linux/init.h> -#include <linux/console.h> -#include <linux/sysrq.h> -#include <linux/slab.h> -#include <linux/platform_device.h> -#include <linux/tty.h> -#include <linux/tty_flip.h> -#include <linux/serial_core.h> -#include <linux/gpio.h> - -#include <asm/bfin_sport.h> -#include <asm/delay.h> -#include <asm/portmux.h> - -#include "bfin_sport_uart.h" - -struct sport_uart_port { - struct uart_port port; - int err_irq; - unsigned short csize; - unsigned short rxmask; - unsigned short txmask1; - unsigned short txmask2; - unsigned char stopb; -/* unsigned char parib; */ -#ifdef CONFIG_SERIAL_BFIN_SPORT_CTSRTS - int cts_pin; - int rts_pin; -#endif -}; - -static int sport_uart_tx_chars(struct sport_uart_port *up); -static void sport_stop_tx(struct uart_port *port); - -static inline void tx_one_byte(struct sport_uart_port *up, unsigned int value) -{ - pr_debug("%s value:%x, mask1=0x%x, mask2=0x%x\n", __func__, value, - up->txmask1, up->txmask2); - - /* Place Start and Stop bits */ - __asm__ __volatile__ ( - "%[val] <<= 1;" - "%[val] = %[val] & %[mask1];" - "%[val] = %[val] | %[mask2];" - : [val]"+d"(value) - : [mask1]"d"(up->txmask1), [mask2]"d"(up->txmask2) - : "ASTAT" - ); - pr_debug("%s value:%x\n", __func__, value); - - SPORT_PUT_TX(up, value); -} - -static inline unsigned char rx_one_byte(struct sport_uart_port *up) -{ - unsigned int value; - unsigned char extract; - u32 tmp_mask1, tmp_mask2, tmp_shift, tmp; - - if ((up->csize + up->stopb) > 7) - value = SPORT_GET_RX32(up); - else - value = SPORT_GET_RX(up); - - pr_debug("%s value:%x, cs=%d, mask=0x%x\n", __func__, value, - up->csize, up->rxmask); - - /* Extract data */ - __asm__ __volatile__ ( - "%[extr] = 0;" - "%[mask1] = %[rxmask];" - "%[mask2] = 0x0200(Z);" - "%[shift] = 0;" - "LSETUP(.Lloop_s, .Lloop_e) LC0 = %[lc];" - ".Lloop_s:" - "%[tmp] = extract(%[val], %[mask1].L)(Z);" - "%[tmp] <<= %[shift];" - "%[extr] = %[extr] | %[tmp];" - "%[mask1] = %[mask1] - %[mask2];" - ".Lloop_e:" - "%[shift] += 1;" - : [extr]"=&d"(extract), [shift]"=&d"(tmp_shift), [tmp]"=&d"(tmp), - [mask1]"=&d"(tmp_mask1), [mask2]"=&d"(tmp_mask2) - : [val]"d"(value), [rxmask]"d"(up->rxmask), [lc]"a"(up->csize) - : "ASTAT", "LB0", "LC0", "LT0" - ); - - pr_debug(" extract:%x\n", extract); - return extract; -} - -static int sport_uart_setup(struct sport_uart_port *up, int size, int baud_rate) -{ - int tclkdiv, rclkdiv; - unsigned int sclk = get_sclk(); - - /* Set TCR1 and TCR2, TFSR is not enabled for uart */ - SPORT_PUT_TCR1(up, (LATFS | ITFS | TFSR | TLSBIT | ITCLK)); - SPORT_PUT_TCR2(up, size + 1); - pr_debug("%s TCR1:%x, TCR2:%x\n", __func__, SPORT_GET_TCR1(up), SPORT_GET_TCR2(up)); - - /* Set RCR1 and RCR2 */ - SPORT_PUT_RCR1(up, (RCKFE | LARFS | LRFS | RFSR | IRCLK)); - SPORT_PUT_RCR2(up, (size + 1) * 2 - 1); - pr_debug("%s RCR1:%x, RCR2:%x\n", __func__, SPORT_GET_RCR1(up), SPORT_GET_RCR2(up)); - - tclkdiv = sclk / (2 * baud_rate) - 1; - /* The actual uart baud rate of devices vary between +/-2%. The sport - * RX sample rate should be faster than the double of the worst case, - * otherwise, wrong data are received. So, set sport RX clock to be - * 3% faster. - */ - rclkdiv = sclk / (2 * baud_rate * 2 * 97 / 100) - 1; - SPORT_PUT_TCLKDIV(up, tclkdiv); - SPORT_PUT_RCLKDIV(up, rclkdiv); - SSYNC(); - pr_debug("%s sclk:%d, baud_rate:%d, tclkdiv:%d, rclkdiv:%d\n", - __func__, sclk, baud_rate, tclkdiv, rclkdiv); - - return 0; -} - -static irqreturn_t sport_uart_rx_irq(int irq, void *dev_id) -{ - struct sport_uart_port *up = dev_id; - struct tty_port *port = &up->port.state->port; - unsigned int ch; - - spin_lock(&up->port.lock); - - while (SPORT_GET_STAT(up) & RXNE) { - ch = rx_one_byte(up); - up->port.icount.rx++; - - if (!uart_handle_sysrq_char(&up->port, ch)) - tty_insert_flip_char(port, ch, TTY_NORMAL); - } - - spin_unlock(&up->port.lock); - - /* XXX this won't deadlock with lowlat? */ - tty_flip_buffer_push(port); - - return IRQ_HANDLED; -} - -static irqreturn_t sport_uart_tx_irq(int irq, void *dev_id) -{ - struct sport_uart_port *up = dev_id; - - spin_lock(&up->port.lock); - sport_uart_tx_chars(up); - spin_unlock(&up->port.lock); - - return IRQ_HANDLED; -} - -static irqreturn_t sport_uart_err_irq(int irq, void *dev_id) -{ - struct sport_uart_port *up = dev_id; - unsigned int stat = SPORT_GET_STAT(up); - - spin_lock(&up->port.lock); - - /* Overflow in RX FIFO */ - if (stat & ROVF) { - up->port.icount.overrun++; - tty_insert_flip_char(&up->port.state->port, 0, TTY_OVERRUN); - SPORT_PUT_STAT(up, ROVF); /* Clear ROVF bit */ - } - /* These should not happen */ - if (stat & (TOVF | TUVF | RUVF)) { - pr_err("SPORT Error:%s %s %s\n", - (stat & TOVF) ? "TX overflow" : "", - (stat & TUVF) ? "TX underflow" : "", - (stat & RUVF) ? "RX underflow" : ""); - SPORT_PUT_TCR1(up, SPORT_GET_TCR1(up) & ~TSPEN); - SPORT_PUT_RCR1(up, SPORT_GET_RCR1(up) & ~RSPEN); - } - SSYNC(); - - spin_unlock(&up->port.lock); - /* XXX we don't push the overrun bit to TTY? */ - - return IRQ_HANDLED; -} - -#ifdef CONFIG_SERIAL_BFIN_SPORT_CTSRTS -static unsigned int sport_get_mctrl(struct uart_port *port) -{ - struct sport_uart_port *up = (struct sport_uart_port *)port; - if (up->cts_pin < 0) - return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; - - /* CTS PIN is negative assertive. */ - if (SPORT_UART_GET_CTS(up)) - return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; - else - return TIOCM_DSR | TIOCM_CAR; -} - -static void sport_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ - struct sport_uart_port *up = (struct sport_uart_port *)port; - if (up->rts_pin < 0) - return; - - /* RTS PIN is negative assertive. */ - if (mctrl & TIOCM_RTS) - SPORT_UART_ENABLE_RTS(up); - else - SPORT_UART_DISABLE_RTS(up); -} - -/* - * Handle any change of modem status signal. - */ -static irqreturn_t sport_mctrl_cts_int(int irq, void *dev_id) -{ - struct sport_uart_port *up = (struct sport_uart_port *)dev_id; - unsigned int status; - - status = sport_get_mctrl(&up->port); - uart_handle_cts_change(&up->port, status & TIOCM_CTS); - - return IRQ_HANDLED; -} -#else -static unsigned int sport_get_mctrl(struct uart_port *port) -{ - pr_debug("%s enter\n", __func__); - return TIOCM_CTS | TIOCM_CD | TIOCM_DSR; -} - -static void sport_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ - pr_debug("%s enter\n", __func__); -} -#endif - -/* Reqeust IRQ, Setup clock */ -static int sport_startup(struct uart_port *port) -{ - struct sport_uart_port *up = (struct sport_uart_port *)port; - int ret; - - pr_debug("%s enter\n", __func__); - ret = request_irq(up->port.irq, sport_uart_rx_irq, 0, - "SPORT_UART_RX", up); - if (ret) { - dev_err(port->dev, "unable to request SPORT RX interrupt\n"); - return ret; - } - - ret = request_irq(up->port.irq+1, sport_uart_tx_irq, 0, - "SPORT_UART_TX", up); - if (ret) { - dev_err(port->dev, "unable to request SPORT TX interrupt\n"); - goto fail1; - } - - ret = request_irq(up->err_irq, sport_uart_err_irq, 0, - "SPORT_UART_STATUS", up); - if (ret) { - dev_err(port->dev, "unable to request SPORT status interrupt\n"); - goto fail2; - } - -#ifdef CONFIG_SERIAL_BFIN_SPORT_CTSRTS - if (up->cts_pin >= 0) { - if (request_irq(gpio_to_irq(up->cts_pin), - sport_mctrl_cts_int, - IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | - 0, "BFIN_SPORT_UART_CTS", up)) { - up->cts_pin = -1; - dev_info(port->dev, "Unable to attach BlackFin UART over SPORT CTS interrupt. So, disable it.\n"); - } - } - if (up->rts_pin >= 0) { - if (gpio_request(up->rts_pin, DRV_NAME)) { - dev_info(port->dev, "fail to request RTS PIN at GPIO_%d\n", up->rts_pin); - up->rts_pin = -1; - } else - gpio_direction_output(up->rts_pin, 0); - } -#endif - - return 0; - fail2: - free_irq(up->port.irq+1, up); - fail1: - free_irq(up->port.irq, up); - - return ret; -} - -/* - * sport_uart_tx_chars - * - * ret 1 means need to enable sport. - * ret 0 means do nothing. - */ -static int sport_uart_tx_chars(struct sport_uart_port *up) -{ - struct circ_buf *xmit = &up->port.state->xmit; - - if (SPORT_GET_STAT(up) & TXF) - return 0; - - if (up->port.x_char) { - tx_one_byte(up, up->port.x_char); - up->port.icount.tx++; - up->port.x_char = 0; - return 1; - } - - if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) { - /* The waiting loop to stop SPORT TX from TX interrupt is - * too long. This may block SPORT RX interrupts and cause - * RX FIFO overflow. So, do stop sport TX only after the last - * char in TX FIFO is moved into the shift register. - */ - if (SPORT_GET_STAT(up) & TXHRE) - sport_stop_tx(&up->port); - return 0; - } - - while(!(SPORT_GET_STAT(up) & TXF) && !uart_circ_empty(xmit)) { - tx_one_byte(up, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE -1); - up->port.icount.tx++; - } - - if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) - uart_write_wakeup(&up->port); - - return 1; -} - -static unsigned int sport_tx_empty(struct uart_port *port) -{ - struct sport_uart_port *up = (struct sport_uart_port *)port; - unsigned int stat; - - stat = SPORT_GET_STAT(up); - pr_debug("%s stat:%04x\n", __func__, stat); - if (stat & TXHRE) { - return TIOCSER_TEMT; - } else - return 0; -} - -static void sport_stop_tx(struct uart_port *port) -{ - struct sport_uart_port *up = (struct sport_uart_port *)port; - - pr_debug("%s enter\n", __func__); - - if (!(SPORT_GET_TCR1(up) & TSPEN)) - return; - - /* Although the hold register is empty, last byte is still in shift - * register and not sent out yet. So, put a dummy data into TX FIFO. - * Then, sport tx stops when last byte is shift out and the dummy - * data is moved into the shift register. - */ - SPORT_PUT_TX(up, 0xffff); - while (!(SPORT_GET_STAT(up) & TXHRE)) - cpu_relax(); - - SPORT_PUT_TCR1(up, (SPORT_GET_TCR1(up) & ~TSPEN)); - SSYNC(); - - return; -} - -static void sport_start_tx(struct uart_port *port) -{ - struct sport_uart_port *up = (struct sport_uart_port *)port; - - pr_debug("%s enter\n", __func__); - - /* Write data into SPORT FIFO before enable SPROT to transmit */ - if (sport_uart_tx_chars(up)) { - /* Enable transmit, then an interrupt will generated */ - SPORT_PUT_TCR1(up, (SPORT_GET_TCR1(up) | TSPEN)); - SSYNC(); - } - - pr_debug("%s exit\n", __func__); -} - -static void sport_stop_rx(struct uart_port *port) -{ - struct sport_uart_port *up = (struct sport_uart_port *)port; - - pr_debug("%s enter\n", __func__); - /* Disable sport to stop rx */ - SPORT_PUT_RCR1(up, (SPORT_GET_RCR1(up) & ~RSPEN)); - SSYNC(); -} - -static void sport_break_ctl(struct uart_port *port, int break_state) -{ - pr_debug("%s enter\n", __func__); -} - -static void sport_shutdown(struct uart_port *port) -{ - struct sport_uart_port *up = (struct sport_uart_port *)port; - - dev_dbg(port->dev, "%s enter\n", __func__); - - /* Disable sport */ - SPORT_PUT_TCR1(up, (SPORT_GET_TCR1(up) & ~TSPEN)); - SPORT_PUT_RCR1(up, (SPORT_GET_RCR1(up) & ~RSPEN)); - SSYNC(); - - free_irq(up->port.irq, up); - free_irq(up->port.irq+1, up); - free_irq(up->err_irq, up); -#ifdef CONFIG_SERIAL_BFIN_SPORT_CTSRTS - if (up->cts_pin >= 0) - free_irq(gpio_to_irq(up->cts_pin), up); - if (up->rts_pin >= 0) - gpio_free(up->rts_pin); -#endif -} - -static const char *sport_type(struct uart_port *port) -{ - struct sport_uart_port *up = (struct sport_uart_port *)port; - - pr_debug("%s enter\n", __func__); - return up->port.type == PORT_BFIN_SPORT ? "BFIN-SPORT-UART" : NULL; -} - -static void sport_release_port(struct uart_port *port) -{ - pr_debug("%s enter\n", __func__); -} - -static int sport_request_port(struct uart_port *port) -{ - pr_debug("%s enter\n", __func__); - return 0; -} - -static void sport_config_port(struct uart_port *port, int flags) -{ - struct sport_uart_port *up = (struct sport_uart_port *)port; - - pr_debug("%s enter\n", __func__); - up->port.type = PORT_BFIN_SPORT; -} - -static int sport_verify_port(struct uart_port *port, struct serial_struct *ser) -{ - pr_debug("%s enter\n", __func__); - return 0; -} - -static void sport_set_termios(struct uart_port *port, - struct ktermios *termios, struct ktermios *old) -{ - struct sport_uart_port *up = (struct sport_uart_port *)port; - unsigned long flags; - int i; - - pr_debug("%s enter, c_cflag:%08x\n", __func__, termios->c_cflag); - -#ifdef CONFIG_SERIAL_BFIN_SPORT_CTSRTS - if (old == NULL && up->cts_pin != -1) - termios->c_cflag |= CRTSCTS; - else if (up->cts_pin == -1) - termios->c_cflag &= ~CRTSCTS; -#endif - - switch (termios->c_cflag & CSIZE) { - case CS8: - up->csize = 8; - break; - case CS7: - up->csize = 7; - break; - case CS6: - up->csize = 6; - break; - case CS5: - up->csize = 5; - break; - default: - pr_warn("requested word length not supported\n"); - break; - } - - if (termios->c_cflag & CSTOPB) { - up->stopb = 1; - } - if (termios->c_cflag & PARENB) { - pr_warn("PAREN bit is not supported yet\n"); - /* up->parib = 1; */ - } - - spin_lock_irqsave(&up->port.lock, flags); - - port->read_status_mask = 0; - - /* - * Characters to ignore - */ - port->ignore_status_mask = 0; - - /* RX extract mask */ - up->rxmask = 0x01 | (((up->csize + up->stopb) * 2 - 1) << 0x8); - /* TX masks, 8 bit data and 1 bit stop for example: - * mask1 = b#0111111110 - * mask2 = b#1000000000 - */ - for (i = 0, up->txmask1 = 0; i < up->csize; i++) - up->txmask1 |= (1<<i); - up->txmask2 = (1<<i); - if (up->stopb) { - ++i; - up->txmask2 |= (1<<i); - } - up->txmask1 <<= 1; - up->txmask2 <<= 1; - /* uart baud rate */ - port->uartclk = uart_get_baud_rate(port, termios, old, 0, get_sclk()/16); - - /* Disable UART */ - SPORT_PUT_TCR1(up, SPORT_GET_TCR1(up) & ~TSPEN); - SPORT_PUT_RCR1(up, SPORT_GET_RCR1(up) & ~RSPEN); - - sport_uart_setup(up, up->csize + up->stopb, port->uartclk); - - /* driver TX line high after config, one dummy data is - * necessary to stop sport after shift one byte - */ - SPORT_PUT_TX(up, 0xffff); - SPORT_PUT_TX(up, 0xffff); - SPORT_PUT_TCR1(up, (SPORT_GET_TCR1(up) | TSPEN)); - SSYNC(); - while (!(SPORT_GET_STAT(up) & TXHRE)) - cpu_relax(); - SPORT_PUT_TCR1(up, SPORT_GET_TCR1(up) & ~TSPEN); - SSYNC(); - - /* Port speed changed, update the per-port timeout. */ - uart_update_timeout(port, termios->c_cflag, port->uartclk); - - /* Enable sport rx */ - SPORT_PUT_RCR1(up, SPORT_GET_RCR1(up) | RSPEN); - SSYNC(); - - spin_unlock_irqrestore(&up->port.lock, flags); -} - -static const struct uart_ops sport_uart_ops = { - .tx_empty = sport_tx_empty, - .set_mctrl = sport_set_mctrl, - .get_mctrl = sport_get_mctrl, - .stop_tx = sport_stop_tx, - .start_tx = sport_start_tx, - .stop_rx = sport_stop_rx, - .break_ctl = sport_break_ctl, - .startup = sport_startup, - .shutdown = sport_shutdown, - .set_termios = sport_set_termios, - .type = sport_type, - .release_port = sport_release_port, - .request_port = sport_request_port, - .config_port = sport_config_port, - .verify_port = sport_verify_port, -}; - -#define BFIN_SPORT_UART_MAX_PORTS 4 - -static struct sport_uart_port *bfin_sport_uart_ports[BFIN_SPORT_UART_MAX_PORTS]; - -#ifdef CONFIG_SERIAL_BFIN_SPORT_CONSOLE -#define CLASS_BFIN_SPORT_CONSOLE "bfin-sport-console" - -static int __init -sport_uart_console_setup(struct console *co, char *options) -{ - struct sport_uart_port *up; - int baud = 57600; - int bits = 8; - int parity = 'n'; -# ifdef CONFIG_SERIAL_BFIN_SPORT_CTSRTS - int flow = 'r'; -# else - int flow = 'n'; -# endif - - /* Check whether an invalid uart number has been specified */ - if (co->index < 0 || co->index >= BFIN_SPORT_UART_MAX_PORTS) - return -ENODEV; - - up = bfin_sport_uart_ports[co->index]; - if (!up) - return -ENODEV; - - if (options) - uart_parse_options(options, &baud, &parity, &bits, &flow); - - return uart_set_options(&up->port, co, baud, parity, bits, flow); -} - -static void sport_uart_console_putchar(struct uart_port *port, int ch) -{ - struct sport_uart_port *up = (struct sport_uart_port *)port; - - while (SPORT_GET_STAT(up) & TXF) - barrier(); - - tx_one_byte(up, ch); -} - -/* - * Interrupts are disabled on entering - */ -static void -sport_uart_console_write(struct console *co, const char *s, unsigned int count) -{ - struct sport_uart_port *up = bfin_sport_uart_ports[co->index]; - unsigned long flags; - - spin_lock_irqsave(&up->port.lock, flags); - - if (SPORT_GET_TCR1(up) & TSPEN) - uart_console_write(&up->port, s, count, sport_uart_console_putchar); - else { - /* dummy data to start sport */ - while (SPORT_GET_STAT(up) & TXF) - barrier(); - SPORT_PUT_TX(up, 0xffff); - /* Enable transmit, then an interrupt will generated */ - SPORT_PUT_TCR1(up, (SPORT_GET_TCR1(up) | TSPEN)); - SSYNC(); - - uart_console_write(&up->port, s, count, sport_uart_console_putchar); - - /* Although the hold register is empty, last byte is still in shift - * register and not sent out yet. So, put a dummy data into TX FIFO. - * Then, sport tx stops when last byte is shift out and the dummy - * data is moved into the shift register. - */ - while (SPORT_GET_STAT(up) & TXF) - barrier(); - SPORT_PUT_TX(up, 0xffff); - while (!(SPORT_GET_STAT(up) & TXHRE)) - barrier(); - - /* Stop sport tx transfer */ - SPORT_PUT_TCR1(up, (SPORT_GET_TCR1(up) & ~TSPEN)); - SSYNC(); - } - - spin_unlock_irqrestore(&up->port.lock, flags); -} - -static struct uart_driver sport_uart_reg; - -static struct console sport_uart_console = { - .name = DEVICE_NAME, - .write = sport_uart_console_write, - .device = uart_console_device, - .setup = sport_uart_console_setup, - .flags = CON_PRINTBUFFER, - .index = -1, - .data = &sport_uart_reg, -}; - -#define SPORT_UART_CONSOLE (&sport_uart_console) -#else -#define SPORT_UART_CONSOLE NULL -#endif /* CONFIG_SERIAL_BFIN_SPORT_CONSOLE */ - - -static struct uart_driver sport_uart_reg = { - .owner = THIS_MODULE, - .driver_name = DRV_NAME, - .dev_name = DEVICE_NAME, - .major = 204, - .minor = 84, - .nr = BFIN_SPORT_UART_MAX_PORTS, - .cons = SPORT_UART_CONSOLE, -}; - -#ifdef CONFIG_PM -static int sport_uart_suspend(struct device *dev) -{ - struct sport_uart_port *sport = dev_get_drvdata(dev); - - dev_dbg(dev, "%s enter\n", __func__); - if (sport) - uart_suspend_port(&sport_uart_reg, &sport->port); - - return 0; -} - -static int sport_uart_resume(struct device *dev) -{ - struct sport_uart_port *sport = dev_get_drvdata(dev); - - dev_dbg(dev, "%s enter\n", __func__); - if (sport) - uart_resume_port(&sport_uart_reg, &sport->port); - - return 0; -} - -static const struct dev_pm_ops bfin_sport_uart_dev_pm_ops = { - .suspend = sport_uart_suspend, - .resume = sport_uart_resume, -}; -#endif - -static int sport_uart_probe(struct platform_device *pdev) -{ - struct resource *res; - struct sport_uart_port *sport; - int ret = 0; - - dev_dbg(&pdev->dev, "%s enter\n", __func__); - - if (pdev->id < 0 || pdev->id >= BFIN_SPORT_UART_MAX_PORTS) { - dev_err(&pdev->dev, "Wrong sport uart platform device id.\n"); - return -ENOENT; - } - - if (bfin_sport_uart_ports[pdev->id] == NULL) { - bfin_sport_uart_ports[pdev->id] = - kzalloc(sizeof(struct sport_uart_port), GFP_KERNEL); - sport = bfin_sport_uart_ports[pdev->id]; - if (!sport) { - dev_err(&pdev->dev, - "Fail to malloc sport_uart_port\n"); - return -ENOMEM; - } - - ret = peripheral_request_list(dev_get_platdata(&pdev->dev), - DRV_NAME); - if (ret) { - dev_err(&pdev->dev, - "Fail to request SPORT peripherals\n"); - goto out_error_free_mem; - } - - spin_lock_init(&sport->port.lock); - sport->port.fifosize = SPORT_TX_FIFO_SIZE, - sport->port.ops = &sport_uart_ops; - sport->port.line = pdev->id; - sport->port.iotype = UPIO_MEM; - sport->port.flags = UPF_BOOT_AUTOCONF; - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (res == NULL) { - dev_err(&pdev->dev, "Cannot get IORESOURCE_MEM\n"); - ret = -ENOENT; - goto out_error_free_peripherals; - } - - sport->port.membase = ioremap(res->start, resource_size(res)); - if (!sport->port.membase) { - dev_err(&pdev->dev, "Cannot map sport IO\n"); - ret = -ENXIO; - goto out_error_free_peripherals; - } - sport->port.mapbase = res->start; - - sport->port.irq = platform_get_irq(pdev, 0); - if ((int)sport->port.irq < 0) { - dev_err(&pdev->dev, "No sport RX/TX IRQ specified\n"); - ret = -ENOENT; - goto out_error_unmap; - } - - sport->err_irq = platform_get_irq(pdev, 1); - if (sport->err_irq < 0) { - dev_err(&pdev->dev, "No sport status IRQ specified\n"); - ret = -ENOENT; - goto out_error_unmap; - } -#ifdef CONFIG_SERIAL_BFIN_SPORT_CTSRTS - res = platform_get_resource(pdev, IORESOURCE_IO, 0); - if (res == NULL) - sport->cts_pin = -1; - else - sport->cts_pin = res->start; - - res = platform_get_resource(pdev, IORESOURCE_IO, 1); - if (res == NULL) - sport->rts_pin = -1; - else - sport->rts_pin = res->start; -#endif - } - -#ifdef CONFIG_SERIAL_BFIN_SPORT_CONSOLE - if (!is_early_platform_device(pdev)) { -#endif - sport = bfin_sport_uart_ports[pdev->id]; - sport->port.dev = &pdev->dev; - dev_set_drvdata(&pdev->dev, sport); - ret = uart_add_one_port(&sport_uart_reg, &sport->port); -#ifdef CONFIG_SERIAL_BFIN_SPORT_CONSOLE - } -#endif - if (!ret) - return 0; - - if (sport) { -out_error_unmap: - iounmap(sport->port.membase); -out_error_free_peripherals: - peripheral_free_list(dev_get_platdata(&pdev->dev)); -out_error_free_mem: - kfree(sport); - bfin_sport_uart_ports[pdev->id] = NULL; - } - - return ret; -} - -static int sport_uart_remove(struct platform_device *pdev) -{ - struct sport_uart_port *sport = platform_get_drvdata(pdev); - - dev_dbg(&pdev->dev, "%s enter\n", __func__); - dev_set_drvdata(&pdev->dev, NULL); - - if (sport) { - uart_remove_one_port(&sport_uart_reg, &sport->port); - iounmap(sport->port.membase); - peripheral_free_list(dev_get_platdata(&pdev->dev)); - kfree(sport); - bfin_sport_uart_ports[pdev->id] = NULL; - } - - return 0; -} - -static struct platform_driver sport_uart_driver = { - .probe = sport_uart_probe, - .remove = sport_uart_remove, - .driver = { - .name = DRV_NAME, -#ifdef CONFIG_PM - .pm = &bfin_sport_uart_dev_pm_ops, -#endif - }, -}; - -#ifdef CONFIG_SERIAL_BFIN_SPORT_CONSOLE -static struct early_platform_driver early_sport_uart_driver __initdata = { - .class_str = CLASS_BFIN_SPORT_CONSOLE, - .pdrv = &sport_uart_driver, - .requested_id = EARLY_PLATFORM_ID_UNSET, -}; - -static int __init sport_uart_rs_console_init(void) -{ - early_platform_driver_register(&early_sport_uart_driver, DRV_NAME); - - early_platform_driver_probe(CLASS_BFIN_SPORT_CONSOLE, - BFIN_SPORT_UART_MAX_PORTS, 0); - - register_console(&sport_uart_console); - - return 0; -} -console_initcall(sport_uart_rs_console_init); -#endif - -static int __init sport_uart_init(void) -{ - int ret; - - pr_info("Blackfin uart over sport driver\n"); - - ret = uart_register_driver(&sport_uart_reg); - if (ret) { - pr_err("failed to register %s:%d\n", - sport_uart_reg.driver_name, ret); - return ret; - } - - ret = platform_driver_register(&sport_uart_driver); - if (ret) { - pr_err("failed to register sport uart driver:%d\n", ret); - uart_unregister_driver(&sport_uart_reg); - } - - return ret; -} -module_init(sport_uart_init); - -static void __exit sport_uart_exit(void) -{ - platform_driver_unregister(&sport_uart_driver); - uart_unregister_driver(&sport_uart_reg); -} -module_exit(sport_uart_exit); - -MODULE_AUTHOR("Sonic Zhang, Roy Huang"); -MODULE_DESCRIPTION("Blackfin serial over SPORT driver"); -MODULE_LICENSE("GPL"); diff --git a/drivers/tty/serial/bfin_sport_uart.h b/drivers/tty/serial/bfin_sport_uart.h deleted file mode 100644 index 4b12f45d6580..000000000000 --- a/drivers/tty/serial/bfin_sport_uart.h +++ /dev/null @@ -1,86 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Blackfin On-Chip Sport Emulated UART Driver - * - * Copyright 2006-2008 Analog Devices Inc. - * - * Enter bugs at http://blackfin.uclinux.org/ - */ - -/* - * This driver and the hardware supported are in term of EE-191 of ADI. - * http://www.analog.com/static/imported-files/application_notes/EE191.pdf - * This application note describe how to implement a UART on a Sharc DSP, - * but this driver is implemented on Blackfin Processor. - * Transmit Frame Sync is not used by this driver to transfer data out. - */ - -#ifndef _BFIN_SPORT_UART_H -#define _BFIN_SPORT_UART_H - -#define OFFSET_TCR1 0x00 /* Transmit Configuration 1 Register */ -#define OFFSET_TCR2 0x04 /* Transmit Configuration 2 Register */ -#define OFFSET_TCLKDIV 0x08 /* Transmit Serial Clock Divider Register */ -#define OFFSET_TFSDIV 0x0C /* Transmit Frame Sync Divider Register */ -#define OFFSET_TX 0x10 /* Transmit Data Register */ -#define OFFSET_RX 0x18 /* Receive Data Register */ -#define OFFSET_RCR1 0x20 /* Receive Configuration 1 Register */ -#define OFFSET_RCR2 0x24 /* Receive Configuration 2 Register */ -#define OFFSET_RCLKDIV 0x28 /* Receive Serial Clock Divider Register */ -#define OFFSET_RFSDIV 0x2c /* Receive Frame Sync Divider Register */ -#define OFFSET_STAT 0x30 /* Status Register */ - -#define SPORT_GET_TCR1(sport) bfin_read16(((sport)->port.membase + OFFSET_TCR1)) -#define SPORT_GET_TCR2(sport) bfin_read16(((sport)->port.membase + OFFSET_TCR2)) -#define SPORT_GET_TCLKDIV(sport) bfin_read16(((sport)->port.membase + OFFSET_TCLKDIV)) -#define SPORT_GET_TFSDIV(sport) bfin_read16(((sport)->port.membase + OFFSET_TFSDIV)) -#define SPORT_GET_TX(sport) bfin_read16(((sport)->port.membase + OFFSET_TX)) -#define SPORT_GET_RX(sport) bfin_read16(((sport)->port.membase + OFFSET_RX)) -/* - * If another interrupt fires while doing a 32-bit read from RX FIFO, - * a fake RX underflow error will be generated. So disable interrupts - * to prevent interruption while reading the FIFO. - */ -#define SPORT_GET_RX32(sport) \ -({ \ - unsigned int __ret; \ - unsigned long flags; \ - if (ANOMALY_05000473) \ - local_irq_save(flags); \ - __ret = bfin_read32((sport)->port.membase + OFFSET_RX); \ - if (ANOMALY_05000473) \ - local_irq_restore(flags); \ - __ret; \ -}) -#define SPORT_GET_RCR1(sport) bfin_read16(((sport)->port.membase + OFFSET_RCR1)) -#define SPORT_GET_RCR2(sport) bfin_read16(((sport)->port.membase + OFFSET_RCR2)) -#define SPORT_GET_RCLKDIV(sport) bfin_read16(((sport)->port.membase + OFFSET_RCLKDIV)) -#define SPORT_GET_RFSDIV(sport) bfin_read16(((sport)->port.membase + OFFSET_RFSDIV)) -#define SPORT_GET_STAT(sport) bfin_read16(((sport)->port.membase + OFFSET_STAT)) - -#define SPORT_PUT_TCR1(sport, v) bfin_write16(((sport)->port.membase + OFFSET_TCR1), v) -#define SPORT_PUT_TCR2(sport, v) bfin_write16(((sport)->port.membase + OFFSET_TCR2), v) -#define SPORT_PUT_TCLKDIV(sport, v) bfin_write16(((sport)->port.membase + OFFSET_TCLKDIV), v) -#define SPORT_PUT_TFSDIV(sport, v) bfin_write16(((sport)->port.membase + OFFSET_TFSDIV), v) -#define SPORT_PUT_TX(sport, v) bfin_write16(((sport)->port.membase + OFFSET_TX), v) -#define SPORT_PUT_RX(sport, v) bfin_write16(((sport)->port.membase + OFFSET_RX), v) -#define SPORT_PUT_RCR1(sport, v) bfin_write16(((sport)->port.membase + OFFSET_RCR1), v) -#define SPORT_PUT_RCR2(sport, v) bfin_write16(((sport)->port.membase + OFFSET_RCR2), v) -#define SPORT_PUT_RCLKDIV(sport, v) bfin_write16(((sport)->port.membase + OFFSET_RCLKDIV), v) -#define SPORT_PUT_RFSDIV(sport, v) bfin_write16(((sport)->port.membase + OFFSET_RFSDIV), v) -#define SPORT_PUT_STAT(sport, v) bfin_write16(((sport)->port.membase + OFFSET_STAT), v) - -#define SPORT_TX_FIFO_SIZE 8 - -#define SPORT_UART_GET_CTS(x) gpio_get_value(x->cts_pin) -#define SPORT_UART_DISABLE_RTS(x) gpio_set_value(x->rts_pin, 1) -#define SPORT_UART_ENABLE_RTS(x) gpio_set_value(x->rts_pin, 0) - -#if defined(CONFIG_SERIAL_BFIN_SPORT0_UART_CTSRTS) \ - || defined(CONFIG_SERIAL_BFIN_SPORT1_UART_CTSRTS) \ - || defined(CONFIG_SERIAL_BFIN_SPORT2_UART_CTSRTS) \ - || defined(CONFIG_SERIAL_BFIN_SPORT3_UART_CTSRTS) -# define CONFIG_SERIAL_BFIN_SPORT_CTSRTS -#endif - -#endif /* _BFIN_SPORT_UART_H */ diff --git a/drivers/tty/serial/bfin_uart.c b/drivers/tty/serial/bfin_uart.c deleted file mode 100644 index 4755fa696321..000000000000 --- a/drivers/tty/serial/bfin_uart.c +++ /dev/null @@ -1,1551 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Blackfin On-Chip Serial Driver - * - * Copyright 2006-2011 Analog Devices Inc. - * - * Enter bugs at http://blackfin.uclinux.org/ - */ - -#if defined(CONFIG_SERIAL_BFIN_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) -#define SUPPORT_SYSRQ -#endif - -#define DRIVER_NAME "bfin-uart" -#define pr_fmt(fmt) DRIVER_NAME ": " fmt - -#include <linux/module.h> -#include <linux/ioport.h> -#include <linux/gfp.h> -#include <linux/io.h> -#include <linux/init.h> -#include <linux/console.h> -#include <linux/sysrq.h> -#include <linux/platform_device.h> -#include <linux/tty.h> -#include <linux/tty_flip.h> -#include <linux/serial_core.h> -#include <linux/gpio.h> -#include <linux/irq.h> -#include <linux/kgdb.h> -#include <linux/slab.h> -#include <linux/dma-mapping.h> - -#include <asm/portmux.h> -#include <asm/cacheflush.h> -#include <asm/dma.h> -#include <asm/bfin_serial.h> - -#ifdef CONFIG_SERIAL_BFIN_MODULE -# undef CONFIG_EARLY_PRINTK -#endif - -/* UART name and device definitions */ -#define BFIN_SERIAL_DEV_NAME "ttyBF" -#define BFIN_SERIAL_MAJOR 204 -#define BFIN_SERIAL_MINOR 64 - -static struct bfin_serial_port *bfin_serial_ports[BFIN_UART_NR_PORTS]; - -#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \ - defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE) - -# ifndef CONFIG_SERIAL_BFIN_PIO -# error KGDB only support UART in PIO mode. -# endif - -static int kgdboc_port_line; -static int kgdboc_break_enabled; -#endif -/* - * Setup for console. Argument comes from the menuconfig - */ -#define DMA_RX_XCOUNT 512 -#define DMA_RX_YCOUNT (PAGE_SIZE / DMA_RX_XCOUNT) - -#define DMA_RX_FLUSH_JIFFIES (HZ / 50) - -#ifdef CONFIG_SERIAL_BFIN_DMA -static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart); -#else -static void bfin_serial_tx_chars(struct bfin_serial_port *uart); -#endif - -static void bfin_serial_reset_irda(struct uart_port *port); - -#if defined(SERIAL_BFIN_CTSRTS) || \ - defined(SERIAL_BFIN_HARD_CTSRTS) -static unsigned int bfin_serial_get_mctrl(struct uart_port *port) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - if (uart->cts_pin < 0) - return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; - - /* CTS PIN is negative assertive. */ - if (UART_GET_CTS(uart)) - return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; - else - return TIOCM_DSR | TIOCM_CAR; -} - -static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - if (uart->rts_pin < 0) - return; - - /* RTS PIN is negative assertive. */ - if (mctrl & TIOCM_RTS) - UART_ENABLE_RTS(uart); - else - UART_DISABLE_RTS(uart); -} - -/* - * Handle any change of modem status signal. - */ -static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id) -{ - struct bfin_serial_port *uart = dev_id; - struct uart_port *uport = &uart->port; - unsigned int status = bfin_serial_get_mctrl(uport); -#ifdef SERIAL_BFIN_HARD_CTSRTS - - UART_CLEAR_SCTS(uart); - if (uport->hw_stopped) { - if (status) { - uport->hw_stopped = 0; - uart_write_wakeup(uport); - } - } else { - if (!status) - uport->hw_stopped = 1; - } -#else - uart_handle_cts_change(uport, status & TIOCM_CTS); -#endif - - return IRQ_HANDLED; -} -#else -static unsigned int bfin_serial_get_mctrl(struct uart_port *port) -{ - return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; -} - -static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ -} -#endif - -/* - * interrupts are disabled on entry - */ -static void bfin_serial_stop_tx(struct uart_port *port) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; -#ifdef CONFIG_SERIAL_BFIN_DMA - struct circ_buf *xmit = &uart->port.state->xmit; -#endif - - while (!(UART_GET_LSR(uart) & TEMT)) - cpu_relax(); - -#ifdef CONFIG_SERIAL_BFIN_DMA - disable_dma(uart->tx_dma_channel); - xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1); - uart->port.icount.tx += uart->tx_count; - uart->tx_count = 0; - uart->tx_done = 1; -#else -#if defined(CONFIG_BF54x) || defined(CONFIG_BF60x) - /* Clear TFI bit */ - UART_PUT_LSR(uart, TFI); -#endif - UART_CLEAR_IER(uart, ETBEI); -#endif -} - -/* - * port is locked and interrupts are disabled - */ -static void bfin_serial_start_tx(struct uart_port *port) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - struct tty_struct *tty = uart->port.state->port.tty; - - /* - * To avoid losting RX interrupt, we reset IR function - * before sending data. - */ - if (tty->termios.c_line == N_IRDA) - bfin_serial_reset_irda(port); - -#ifdef CONFIG_SERIAL_BFIN_DMA - if (uart->tx_done) - bfin_serial_dma_tx_chars(uart); -#else - UART_SET_IER(uart, ETBEI); - bfin_serial_tx_chars(uart); -#endif -} - -/* - * Interrupts are enabled - */ -static void bfin_serial_stop_rx(struct uart_port *port) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - - UART_CLEAR_IER(uart, ERBFI); -} - -#if ANOMALY_05000363 && defined(CONFIG_SERIAL_BFIN_PIO) -# define UART_GET_ANOMALY_THRESHOLD(uart) ((uart)->anomaly_threshold) -# define UART_SET_ANOMALY_THRESHOLD(uart, v) ((uart)->anomaly_threshold = (v)) -#else -# define UART_GET_ANOMALY_THRESHOLD(uart) 0 -# define UART_SET_ANOMALY_THRESHOLD(uart, v) -#endif - -#ifdef CONFIG_SERIAL_BFIN_PIO -static void bfin_serial_rx_chars(struct bfin_serial_port *uart) -{ - unsigned int status, ch, flg; - static u64 anomaly_start; - - status = UART_GET_LSR(uart); - UART_CLEAR_LSR(uart); - - ch = UART_GET_CHAR(uart); - uart->port.icount.rx++; - -#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \ - defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE) - if (kgdb_connected && kgdboc_port_line == uart->port.line - && kgdboc_break_enabled) - if (ch == 0x3) {/* Ctrl + C */ - kgdb_breakpoint(); - return; - } - - if (!uart->port.state) - return; -#endif - if (ANOMALY_05000363) { - /* The BF533 (and BF561) family of processors have a nice anomaly - * where they continuously generate characters for a "single" break. - * We have to basically ignore this flood until the "next" valid - * character comes across. Due to the nature of the flood, it is - * not possible to reliably catch bytes that are sent too quickly - * after this break. So application code talking to the Blackfin - * which sends a break signal must allow at least 1.5 character - * times after the end of the break for things to stabilize. This - * timeout was picked as it must absolutely be larger than 1 - * character time +/- some percent. So 1.5 sounds good. All other - * Blackfin families operate properly. Woo. - */ - if (anomaly_start > 0) { - u64 curr, nsecs, threshold_ns; - - if ((~ch & (~ch + 1)) & 0xff) - goto known_good_char; - - curr = ktime_get_ns(); - nsecs = curr - anomaly_start; - if (nsecs >> 32) - goto known_good_char; - - threshold_ns = UART_GET_ANOMALY_THRESHOLD(uart) - * NSEC_PER_USEC; - if (nsecs > threshold_ns) - goto known_good_char; - - if (ch) - anomaly_start = 0; - else - anomaly_start = curr; - - return; - - known_good_char: - status &= ~BI; - anomaly_start = 0; - } - } - - if (status & BI) { - if (ANOMALY_05000363) - if (bfin_revid() < 5) - anomaly_start = ktime_get_ns(); - uart->port.icount.brk++; - if (uart_handle_break(&uart->port)) - goto ignore_char; - status &= ~(PE | FE); - } - if (status & PE) - uart->port.icount.parity++; - if (status & OE) - uart->port.icount.overrun++; - if (status & FE) - uart->port.icount.frame++; - - status &= uart->port.read_status_mask; - - if (status & BI) - flg = TTY_BREAK; - else if (status & PE) - flg = TTY_PARITY; - else if (status & FE) - flg = TTY_FRAME; - else - flg = TTY_NORMAL; - - if (uart_handle_sysrq_char(&uart->port, ch)) - goto ignore_char; - - uart_insert_char(&uart->port, status, OE, ch, flg); - - ignore_char: - tty_flip_buffer_push(&uart->port.state->port); -} - -static void bfin_serial_tx_chars(struct bfin_serial_port *uart) -{ - struct circ_buf *xmit = &uart->port.state->xmit; - - if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) { -#if defined(CONFIG_BF54x) || defined(CONFIG_BF60x) - /* Clear TFI bit */ - UART_PUT_LSR(uart, TFI); -#endif - /* Anomaly notes: - * 05000215 - we always clear ETBEI within last UART TX - * interrupt to end a string. It is always set - * when start a new tx. - */ - UART_CLEAR_IER(uart, ETBEI); - return; - } - - if (uart->port.x_char) { - UART_PUT_CHAR(uart, uart->port.x_char); - uart->port.icount.tx++; - uart->port.x_char = 0; - } - - while ((UART_GET_LSR(uart) & THRE) && xmit->tail != xmit->head) { - UART_PUT_CHAR(uart, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); - uart->port.icount.tx++; - } - - if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) - uart_write_wakeup(&uart->port); -} - -static irqreturn_t bfin_serial_rx_int(int irq, void *dev_id) -{ - struct bfin_serial_port *uart = dev_id; - - while (UART_GET_LSR(uart) & DR) - bfin_serial_rx_chars(uart); - - return IRQ_HANDLED; -} - -static irqreturn_t bfin_serial_tx_int(int irq, void *dev_id) -{ - struct bfin_serial_port *uart = dev_id; - - spin_lock(&uart->port.lock); - if (UART_GET_LSR(uart) & THRE) - bfin_serial_tx_chars(uart); - spin_unlock(&uart->port.lock); - - return IRQ_HANDLED; -} -#endif - -#ifdef CONFIG_SERIAL_BFIN_DMA -static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart) -{ - struct circ_buf *xmit = &uart->port.state->xmit; - - uart->tx_done = 0; - - if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) { - uart->tx_count = 0; - uart->tx_done = 1; - return; - } - - if (uart->port.x_char) { - UART_PUT_CHAR(uart, uart->port.x_char); - uart->port.icount.tx++; - uart->port.x_char = 0; - } - - uart->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE); - if (uart->tx_count > (UART_XMIT_SIZE - xmit->tail)) - uart->tx_count = UART_XMIT_SIZE - xmit->tail; - blackfin_dcache_flush_range((unsigned long)(xmit->buf+xmit->tail), - (unsigned long)(xmit->buf+xmit->tail+uart->tx_count)); - set_dma_config(uart->tx_dma_channel, - set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP, - INTR_ON_BUF, - DIMENSION_LINEAR, - DATA_SIZE_8, - DMA_SYNC_RESTART)); - set_dma_start_addr(uart->tx_dma_channel, (unsigned long)(xmit->buf+xmit->tail)); - set_dma_x_count(uart->tx_dma_channel, uart->tx_count); - set_dma_x_modify(uart->tx_dma_channel, 1); - SSYNC(); - enable_dma(uart->tx_dma_channel); - - UART_SET_IER(uart, ETBEI); -} - -static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart) -{ - int i, flg, status; - - status = UART_GET_LSR(uart); - UART_CLEAR_LSR(uart); - - uart->port.icount.rx += - CIRC_CNT(uart->rx_dma_buf.head, uart->rx_dma_buf.tail, - UART_XMIT_SIZE); - - if (status & BI) { - uart->port.icount.brk++; - if (uart_handle_break(&uart->port)) - goto dma_ignore_char; - status &= ~(PE | FE); - } - if (status & PE) - uart->port.icount.parity++; - if (status & OE) - uart->port.icount.overrun++; - if (status & FE) - uart->port.icount.frame++; - - status &= uart->port.read_status_mask; - - if (status & BI) - flg = TTY_BREAK; - else if (status & PE) - flg = TTY_PARITY; - else if (status & FE) - flg = TTY_FRAME; - else - flg = TTY_NORMAL; - - for (i = uart->rx_dma_buf.tail; ; i++) { - if (i >= UART_XMIT_SIZE) - i = 0; - if (i == uart->rx_dma_buf.head) - break; - if (!uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i])) - uart_insert_char(&uart->port, status, OE, - uart->rx_dma_buf.buf[i], flg); - } - - dma_ignore_char: - tty_flip_buffer_push(&uart->port.state->port); -} - -void bfin_serial_rx_dma_timeout(struct timer_list *t) -{ - struct bfin_serial_port *uart = from_timer(uart, t, rx_dma_timer); - int x_pos, pos; - unsigned long flags; - - dma_disable_irq_nosync(uart->rx_dma_channel); - spin_lock_irqsave(&uart->rx_lock, flags); - - /* 2D DMA RX buffer ring is used. Because curr_y_count and - * curr_x_count can't be read as an atomic operation, - * curr_y_count should be read before curr_x_count. When - * curr_x_count is read, curr_y_count may already indicate - * next buffer line. But, the position calculated here is - * still indicate the old line. The wrong position data may - * be smaller than current buffer tail, which cause garbages - * are received if it is not prohibit. - */ - uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel); - x_pos = get_dma_curr_xcount(uart->rx_dma_channel); - uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows; - if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0) - uart->rx_dma_nrows = 0; - x_pos = DMA_RX_XCOUNT - x_pos; - if (x_pos == DMA_RX_XCOUNT) - x_pos = 0; - - pos = uart->rx_dma_nrows * DMA_RX_XCOUNT + x_pos; - /* Ignore receiving data if new position is in the same line of - * current buffer tail and small. - */ - if (pos > uart->rx_dma_buf.tail || - uart->rx_dma_nrows < (uart->rx_dma_buf.tail/DMA_RX_XCOUNT)) { - uart->rx_dma_buf.head = pos; - bfin_serial_dma_rx_chars(uart); - uart->rx_dma_buf.tail = uart->rx_dma_buf.head; - } - - spin_unlock_irqrestore(&uart->rx_lock, flags); - dma_enable_irq(uart->rx_dma_channel); - - mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES); -} - -static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id) -{ - struct bfin_serial_port *uart = dev_id; - struct circ_buf *xmit = &uart->port.state->xmit; - - spin_lock(&uart->port.lock); - if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) { - disable_dma(uart->tx_dma_channel); - clear_dma_irqstat(uart->tx_dma_channel); - /* Anomaly notes: - * 05000215 - we always clear ETBEI within last UART TX - * interrupt to end a string. It is always set - * when start a new tx. - */ - UART_CLEAR_IER(uart, ETBEI); - uart->port.icount.tx += uart->tx_count; - if (!(xmit->tail == 0 && xmit->head == 0)) { - xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1); - - if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) - uart_write_wakeup(&uart->port); - } - - bfin_serial_dma_tx_chars(uart); - } - - spin_unlock(&uart->port.lock); - return IRQ_HANDLED; -} - -static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id) -{ - struct bfin_serial_port *uart = dev_id; - unsigned int irqstat; - int x_pos, pos; - - spin_lock(&uart->rx_lock); - irqstat = get_dma_curr_irqstat(uart->rx_dma_channel); - clear_dma_irqstat(uart->rx_dma_channel); - - uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel); - x_pos = get_dma_curr_xcount(uart->rx_dma_channel); - uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows; - if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0) - uart->rx_dma_nrows = 0; - - pos = uart->rx_dma_nrows * DMA_RX_XCOUNT; - if (pos > uart->rx_dma_buf.tail || - uart->rx_dma_nrows < (uart->rx_dma_buf.tail/DMA_RX_XCOUNT)) { - uart->rx_dma_buf.head = pos; - bfin_serial_dma_rx_chars(uart); - uart->rx_dma_buf.tail = uart->rx_dma_buf.head; - } - - spin_unlock(&uart->rx_lock); - - return IRQ_HANDLED; -} -#endif - -/* - * Return TIOCSER_TEMT when transmitter is not busy. - */ -static unsigned int bfin_serial_tx_empty(struct uart_port *port) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - unsigned int lsr; - - lsr = UART_GET_LSR(uart); - if (lsr & TEMT) - return TIOCSER_TEMT; - else - return 0; -} - -static void bfin_serial_break_ctl(struct uart_port *port, int break_state) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - u32 lcr = UART_GET_LCR(uart); - if (break_state) - lcr |= SB; - else - lcr &= ~SB; - UART_PUT_LCR(uart, lcr); - SSYNC(); -} - -static int bfin_serial_startup(struct uart_port *port) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - -#ifdef CONFIG_SERIAL_BFIN_DMA - dma_addr_t dma_handle; - - if (request_dma(uart->rx_dma_channel, "BFIN_UART_RX") < 0) { - printk(KERN_NOTICE "Unable to attach Blackfin UART RX DMA channel\n"); - return -EBUSY; - } - - if (request_dma(uart->tx_dma_channel, "BFIN_UART_TX") < 0) { - printk(KERN_NOTICE "Unable to attach Blackfin UART TX DMA channel\n"); - free_dma(uart->rx_dma_channel); - return -EBUSY; - } - - set_dma_callback(uart->rx_dma_channel, bfin_serial_dma_rx_int, uart); - set_dma_callback(uart->tx_dma_channel, bfin_serial_dma_tx_int, uart); - - uart->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL, PAGE_SIZE, &dma_handle, GFP_DMA); - uart->rx_dma_buf.head = 0; - uart->rx_dma_buf.tail = 0; - uart->rx_dma_nrows = 0; - - set_dma_config(uart->rx_dma_channel, - set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO, - INTR_ON_ROW, DIMENSION_2D, - DATA_SIZE_8, - DMA_SYNC_RESTART)); - set_dma_x_count(uart->rx_dma_channel, DMA_RX_XCOUNT); - set_dma_x_modify(uart->rx_dma_channel, 1); - set_dma_y_count(uart->rx_dma_channel, DMA_RX_YCOUNT); - set_dma_y_modify(uart->rx_dma_channel, 1); - set_dma_start_addr(uart->rx_dma_channel, (unsigned long)uart->rx_dma_buf.buf); - enable_dma(uart->rx_dma_channel); - - uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES; - add_timer(&(uart->rx_dma_timer)); -#else -# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \ - defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE) - if (kgdboc_port_line == uart->port.line && kgdboc_break_enabled) - kgdboc_break_enabled = 0; - else { -# endif - if (request_irq(uart->rx_irq, bfin_serial_rx_int, 0, - "BFIN_UART_RX", uart)) { - printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n"); - return -EBUSY; - } - - if (request_irq - (uart->tx_irq, bfin_serial_tx_int, 0, - "BFIN_UART_TX", uart)) { - printk(KERN_NOTICE "Unable to attach BlackFin UART TX interrupt\n"); - free_irq(uart->rx_irq, uart); - return -EBUSY; - } - -# ifdef CONFIG_BF54x - { - /* - * UART2 and UART3 on BF548 share interrupt PINs and DMA - * controllers with SPORT2 and SPORT3. UART rx and tx - * interrupts are generated in PIO mode only when configure - * their peripheral mapping registers properly, which means - * request corresponding DMA channels in PIO mode as well. - */ - unsigned uart_dma_ch_rx, uart_dma_ch_tx; - - switch (uart->rx_irq) { - case IRQ_UART3_RX: - uart_dma_ch_rx = CH_UART3_RX; - uart_dma_ch_tx = CH_UART3_TX; - break; - case IRQ_UART2_RX: - uart_dma_ch_rx = CH_UART2_RX; - uart_dma_ch_tx = CH_UART2_TX; - break; - default: - uart_dma_ch_rx = uart_dma_ch_tx = 0; - break; - } - - if (uart_dma_ch_rx && - request_dma(uart_dma_ch_rx, "BFIN_UART_RX") < 0) { - printk(KERN_NOTICE"Fail to attach UART interrupt\n"); - free_irq(uart->rx_irq, uart); - free_irq(uart->tx_irq, uart); - return -EBUSY; - } - if (uart_dma_ch_tx && - request_dma(uart_dma_ch_tx, "BFIN_UART_TX") < 0) { - printk(KERN_NOTICE "Fail to attach UART interrupt\n"); - free_dma(uart_dma_ch_rx); - free_irq(uart->rx_irq, uart); - free_irq(uart->tx_irq, uart); - return -EBUSY; - } - } -# endif -# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \ - defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE) - } -# endif -#endif - -#ifdef SERIAL_BFIN_CTSRTS - if (uart->cts_pin >= 0) { - if (request_irq(gpio_to_irq(uart->cts_pin), - bfin_serial_mctrl_cts_int, - IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | - 0, "BFIN_UART_CTS", uart)) { - uart->cts_pin = -1; - pr_info("Unable to attach BlackFin UART CTS interrupt. So, disable it.\n"); - } - } - if (uart->rts_pin >= 0) { - if (gpio_request(uart->rts_pin, DRIVER_NAME)) { - pr_info("fail to request RTS PIN at GPIO_%d\n", uart->rts_pin); - uart->rts_pin = -1; - } else - gpio_direction_output(uart->rts_pin, 0); - } -#endif -#ifdef SERIAL_BFIN_HARD_CTSRTS - if (uart->cts_pin >= 0) { - if (request_irq(uart->status_irq, bfin_serial_mctrl_cts_int, - 0, "BFIN_UART_MODEM_STATUS", uart)) { - uart->cts_pin = -1; - dev_info(port->dev, "Unable to attach BlackFin UART Modem Status interrupt.\n"); - } - - /* CTS RTS PINs are negative assertive. */ - UART_PUT_MCR(uart, UART_GET_MCR(uart) | ACTS); - UART_SET_IER(uart, EDSSI); - } -#endif - - UART_SET_IER(uart, ERBFI); - return 0; -} - -static void bfin_serial_shutdown(struct uart_port *port) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - -#ifdef CONFIG_SERIAL_BFIN_DMA - disable_dma(uart->tx_dma_channel); - free_dma(uart->tx_dma_channel); - disable_dma(uart->rx_dma_channel); - free_dma(uart->rx_dma_channel); - del_timer(&(uart->rx_dma_timer)); - dma_free_coherent(NULL, PAGE_SIZE, uart->rx_dma_buf.buf, 0); -#else -#ifdef CONFIG_BF54x - switch (uart->port.irq) { - case IRQ_UART3_RX: - free_dma(CH_UART3_RX); - free_dma(CH_UART3_TX); - break; - case IRQ_UART2_RX: - free_dma(CH_UART2_RX); - free_dma(CH_UART2_TX); - break; - default: - break; - } -#endif - free_irq(uart->rx_irq, uart); - free_irq(uart->tx_irq, uart); -#endif - -#ifdef SERIAL_BFIN_CTSRTS - if (uart->cts_pin >= 0) - free_irq(gpio_to_irq(uart->cts_pin), uart); - if (uart->rts_pin >= 0) - gpio_free(uart->rts_pin); -#endif -#ifdef SERIAL_BFIN_HARD_CTSRTS - if (uart->cts_pin >= 0) - free_irq(uart->status_irq, uart); -#endif -} - -static void -bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios, - struct ktermios *old) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - unsigned long flags; - unsigned int baud, quot; - unsigned int ier, lcr = 0; - unsigned long timeout; - -#ifdef SERIAL_BFIN_CTSRTS - if (old == NULL && uart->cts_pin != -1) - termios->c_cflag |= CRTSCTS; - else if (uart->cts_pin == -1) - termios->c_cflag &= ~CRTSCTS; -#endif - - switch (termios->c_cflag & CSIZE) { - case CS8: - lcr = WLS(8); - break; - case CS7: - lcr = WLS(7); - break; - case CS6: - lcr = WLS(6); - break; - case CS5: - lcr = WLS(5); - break; - default: - printk(KERN_ERR "%s: word length not supported\n", - __func__); - } - - /* Anomaly notes: - * 05000231 - STOP bit is always set to 1 whatever the user is set. - */ - if (termios->c_cflag & CSTOPB) { - if (ANOMALY_05000231) - printk(KERN_WARNING "STOP bits other than 1 is not " - "supported in case of anomaly 05000231.\n"); - else - lcr |= STB; - } - if (termios->c_cflag & PARENB) - lcr |= PEN; - if (!(termios->c_cflag & PARODD)) - lcr |= EPS; - if (termios->c_cflag & CMSPAR) - lcr |= STP; - - spin_lock_irqsave(&uart->port.lock, flags); - - port->read_status_mask = OE; - if (termios->c_iflag & INPCK) - port->read_status_mask |= (FE | PE); - if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) - port->read_status_mask |= BI; - - /* - * Characters to ignore - */ - port->ignore_status_mask = 0; - if (termios->c_iflag & IGNPAR) - port->ignore_status_mask |= FE | PE; - if (termios->c_iflag & IGNBRK) { - port->ignore_status_mask |= BI; - /* - * If we're ignoring parity and break indicators, - * ignore overruns too (for real raw support). - */ - if (termios->c_iflag & IGNPAR) - port->ignore_status_mask |= OE; - } - - baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); - quot = uart_get_divisor(port, baud); - - /* If discipline is not IRDA, apply ANOMALY_05000230 */ - if (termios->c_line != N_IRDA) - quot -= ANOMALY_05000230; - - UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15); - - /* Wait till the transfer buffer is empty */ - timeout = jiffies + msecs_to_jiffies(10); - while (UART_GET_GCTL(uart) & UCEN && !(UART_GET_LSR(uart) & TEMT)) - if (time_after(jiffies, timeout)) { - dev_warn(port->dev, "timeout waiting for TX buffer empty\n"); - break; - } - - /* Disable UART */ - ier = UART_GET_IER(uart); - UART_PUT_GCTL(uart, UART_GET_GCTL(uart) & ~UCEN); - UART_DISABLE_INTS(uart); - - /* Set DLAB in LCR to Access CLK */ - UART_SET_DLAB(uart); - - UART_PUT_CLK(uart, quot); - SSYNC(); - - /* Clear DLAB in LCR to Access THR RBR IER */ - UART_CLEAR_DLAB(uart); - - UART_PUT_LCR(uart, (UART_GET_LCR(uart) & ~LCR_MASK) | lcr); - - /* Enable UART */ - UART_ENABLE_INTS(uart, ier); - UART_PUT_GCTL(uart, UART_GET_GCTL(uart) | UCEN); - - /* Port speed changed, update the per-port timeout. */ - uart_update_timeout(port, termios->c_cflag, baud); - - spin_unlock_irqrestore(&uart->port.lock, flags); -} - -static const char *bfin_serial_type(struct uart_port *port) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - - return uart->port.type == PORT_BFIN ? "BFIN-UART" : NULL; -} - -/* - * Release the memory region(s) being used by 'port'. - */ -static void bfin_serial_release_port(struct uart_port *port) -{ -} - -/* - * Request the memory region(s) being used by 'port'. - */ -static int bfin_serial_request_port(struct uart_port *port) -{ - return 0; -} - -/* - * Configure/autoconfigure the port. - */ -static void bfin_serial_config_port(struct uart_port *port, int flags) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - - if (flags & UART_CONFIG_TYPE && - bfin_serial_request_port(&uart->port) == 0) - uart->port.type = PORT_BFIN; -} - -/* - * Verify the new serial_struct (for TIOCSSERIAL). - * The only change we allow are to the flags and type, and - * even then only between PORT_BFIN and PORT_UNKNOWN - */ -static int -bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser) -{ - return 0; -} - -/* - * Enable the IrDA function if tty->ldisc.num is N_IRDA. - * In other cases, disable IrDA function. - */ -static void bfin_serial_set_ldisc(struct uart_port *port, - struct ktermios *termios) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - unsigned int val; - - switch (termios->c_line) { - case N_IRDA: - val = UART_GET_GCTL(uart); - val |= (UMOD_IRDA | RPOLC); - UART_PUT_GCTL(uart, val); - break; - default: - val = UART_GET_GCTL(uart); - val &= ~(UMOD_MASK | RPOLC); - UART_PUT_GCTL(uart, val); - } -} - -static void bfin_serial_reset_irda(struct uart_port *port) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - unsigned int val; - - val = UART_GET_GCTL(uart); - val &= ~(UMOD_MASK | RPOLC); - UART_PUT_GCTL(uart, val); - SSYNC(); - val |= (UMOD_IRDA | RPOLC); - UART_PUT_GCTL(uart, val); - SSYNC(); -} - -#ifdef CONFIG_CONSOLE_POLL -/* Anomaly notes: - * 05000099 - Because we only use THRE in poll_put and DR in poll_get, - * losing other bits of UART_LSR is not a problem here. - */ -static void bfin_serial_poll_put_char(struct uart_port *port, unsigned char chr) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - - while (!(UART_GET_LSR(uart) & THRE)) - cpu_relax(); - - UART_CLEAR_DLAB(uart); - UART_PUT_CHAR(uart, (unsigned char)chr); -} - -static int bfin_serial_poll_get_char(struct uart_port *port) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - unsigned char chr; - - while (!(UART_GET_LSR(uart) & DR)) - cpu_relax(); - - UART_CLEAR_DLAB(uart); - chr = UART_GET_CHAR(uart); - - return chr; -} -#endif - -static struct uart_ops bfin_serial_pops = { - .tx_empty = bfin_serial_tx_empty, - .set_mctrl = bfin_serial_set_mctrl, - .get_mctrl = bfin_serial_get_mctrl, - .stop_tx = bfin_serial_stop_tx, - .start_tx = bfin_serial_start_tx, - .stop_rx = bfin_serial_stop_rx, - .break_ctl = bfin_serial_break_ctl, - .startup = bfin_serial_startup, - .shutdown = bfin_serial_shutdown, - .set_termios = bfin_serial_set_termios, - .set_ldisc = bfin_serial_set_ldisc, - .type = bfin_serial_type, - .release_port = bfin_serial_release_port, - .request_port = bfin_serial_request_port, - .config_port = bfin_serial_config_port, - .verify_port = bfin_serial_verify_port, -#ifdef CONFIG_CONSOLE_POLL - .poll_put_char = bfin_serial_poll_put_char, - .poll_get_char = bfin_serial_poll_get_char, -#endif -}; - -#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK) -/* - * If the port was already initialised (eg, by a boot loader), - * try to determine the current setup. - */ -static void __init -bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud, - int *parity, int *bits) -{ - unsigned int status; - - status = UART_GET_IER(uart) & (ERBFI | ETBEI); - if (status == (ERBFI | ETBEI)) { - /* ok, the port was enabled */ - u32 lcr, clk; - - lcr = UART_GET_LCR(uart); - - *parity = 'n'; - if (lcr & PEN) { - if (lcr & EPS) - *parity = 'e'; - else - *parity = 'o'; - } - *bits = ((lcr & WLS_MASK) >> WLS_OFFSET) + 5; - - /* Set DLAB in LCR to Access CLK */ - UART_SET_DLAB(uart); - - clk = UART_GET_CLK(uart); - - /* Clear DLAB in LCR to Access THR RBR IER */ - UART_CLEAR_DLAB(uart); - - *baud = get_sclk() / (16*clk); - } - pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __func__, *baud, *parity, *bits); -} - -static struct uart_driver bfin_serial_reg; - -static void bfin_serial_console_putchar(struct uart_port *port, int ch) -{ - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - while (!(UART_GET_LSR(uart) & THRE)) - barrier(); - UART_PUT_CHAR(uart, ch); -} - -#endif /* defined (CONFIG_SERIAL_BFIN_CONSOLE) || - defined (CONFIG_EARLY_PRINTK) */ - -#ifdef CONFIG_SERIAL_BFIN_CONSOLE -#define CLASS_BFIN_CONSOLE "bfin-console" -/* - * Interrupts are disabled on entering - */ -static void -bfin_serial_console_write(struct console *co, const char *s, unsigned int count) -{ - struct bfin_serial_port *uart = bfin_serial_ports[co->index]; - unsigned long flags; - - spin_lock_irqsave(&uart->port.lock, flags); - uart_console_write(&uart->port, s, count, bfin_serial_console_putchar); - spin_unlock_irqrestore(&uart->port.lock, flags); - -} - -static int __init -bfin_serial_console_setup(struct console *co, char *options) -{ - struct bfin_serial_port *uart; - int baud = 57600; - int bits = 8; - int parity = 'n'; -# if defined(SERIAL_BFIN_CTSRTS) || \ - defined(SERIAL_BFIN_HARD_CTSRTS) - int flow = 'r'; -# else - int flow = 'n'; -# endif - - /* - * Check whether an invalid uart number has been specified, and - * if so, search for the first available port that does have - * console support. - */ - if (co->index < 0 || co->index >= BFIN_UART_NR_PORTS) - return -ENODEV; - - uart = bfin_serial_ports[co->index]; - if (!uart) - return -ENODEV; - - if (options) - uart_parse_options(options, &baud, &parity, &bits, &flow); - else - bfin_serial_console_get_options(uart, &baud, &parity, &bits); - - return uart_set_options(&uart->port, co, baud, parity, bits, flow); -} - -static struct console bfin_serial_console = { - .name = BFIN_SERIAL_DEV_NAME, - .write = bfin_serial_console_write, - .device = uart_console_device, - .setup = bfin_serial_console_setup, - .flags = CON_PRINTBUFFER, - .index = -1, - .data = &bfin_serial_reg, -}; -#define BFIN_SERIAL_CONSOLE (&bfin_serial_console) -#else -#define BFIN_SERIAL_CONSOLE NULL -#endif /* CONFIG_SERIAL_BFIN_CONSOLE */ - -#ifdef CONFIG_EARLY_PRINTK -static struct bfin_serial_port bfin_earlyprintk_port; -#define CLASS_BFIN_EARLYPRINTK "bfin-earlyprintk" - -/* - * Interrupts are disabled on entering - */ -static void -bfin_earlyprintk_console_write(struct console *co, const char *s, unsigned int count) -{ - unsigned long flags; - - if (bfin_earlyprintk_port.port.line != co->index) - return; - - spin_lock_irqsave(&bfin_earlyprintk_port.port.lock, flags); - uart_console_write(&bfin_earlyprintk_port.port, s, count, - bfin_serial_console_putchar); - spin_unlock_irqrestore(&bfin_earlyprintk_port.port.lock, flags); -} - -/* - * This should have a .setup or .early_setup in it, but then things get called - * without the command line options, and the baud rate gets messed up - so - * don't let the common infrastructure play with things. (see calls to setup - * & earlysetup in ./kernel/printk.c:register_console() - */ -static struct console bfin_early_serial_console __initdata = { - .name = "early_BFuart", - .write = bfin_earlyprintk_console_write, - .device = uart_console_device, - .flags = CON_PRINTBUFFER, - .index = -1, - .data = &bfin_serial_reg, -}; -#endif - -static struct uart_driver bfin_serial_reg = { - .owner = THIS_MODULE, - .driver_name = DRIVER_NAME, - .dev_name = BFIN_SERIAL_DEV_NAME, - .major = BFIN_SERIAL_MAJOR, - .minor = BFIN_SERIAL_MINOR, - .nr = BFIN_UART_NR_PORTS, - .cons = BFIN_SERIAL_CONSOLE, -}; - -static int bfin_serial_suspend(struct platform_device *pdev, pm_message_t state) -{ - struct bfin_serial_port *uart = platform_get_drvdata(pdev); - - return uart_suspend_port(&bfin_serial_reg, &uart->port); -} - -static int bfin_serial_resume(struct platform_device *pdev) -{ - struct bfin_serial_port *uart = platform_get_drvdata(pdev); - - return uart_resume_port(&bfin_serial_reg, &uart->port); -} - -static int bfin_serial_probe(struct platform_device *pdev) -{ - struct resource *res; - struct bfin_serial_port *uart = NULL; - int ret = 0; - - if (pdev->id < 0 || pdev->id >= BFIN_UART_NR_PORTS) { - dev_err(&pdev->dev, "Wrong bfin uart platform device id.\n"); - return -ENOENT; - } - - if (bfin_serial_ports[pdev->id] == NULL) { - - uart = kzalloc(sizeof(*uart), GFP_KERNEL); - if (!uart) { - dev_err(&pdev->dev, - "fail to malloc bfin_serial_port\n"); - return -ENOMEM; - } - bfin_serial_ports[pdev->id] = uart; - -#ifdef CONFIG_EARLY_PRINTK - if (!(bfin_earlyprintk_port.port.membase - && bfin_earlyprintk_port.port.line == pdev->id)) { - /* - * If the peripheral PINs of current port is allocated - * in earlyprintk probe stage, don't do it again. - */ -#endif - ret = peripheral_request_list( - dev_get_platdata(&pdev->dev), - DRIVER_NAME); - if (ret) { - dev_err(&pdev->dev, - "fail to request bfin serial peripherals\n"); - goto out_error_free_mem; - } -#ifdef CONFIG_EARLY_PRINTK - } -#endif - - spin_lock_init(&uart->port.lock); - uart->port.uartclk = get_sclk(); - uart->port.fifosize = BFIN_UART_TX_FIFO_SIZE; - uart->port.ops = &bfin_serial_pops; - uart->port.line = pdev->id; - uart->port.iotype = UPIO_MEM; - uart->port.flags = UPF_BOOT_AUTOCONF; - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (res == NULL) { - dev_err(&pdev->dev, "Cannot get IORESOURCE_MEM\n"); - ret = -ENOENT; - goto out_error_free_peripherals; - } - - uart->port.membase = ioremap(res->start, resource_size(res)); - if (!uart->port.membase) { - dev_err(&pdev->dev, "Cannot map uart IO\n"); - ret = -ENXIO; - goto out_error_free_peripherals; - } - uart->port.mapbase = res->start; - - uart->tx_irq = platform_get_irq(pdev, 0); - if (uart->tx_irq < 0) { - dev_err(&pdev->dev, "No uart TX IRQ specified\n"); - ret = -ENOENT; - goto out_error_unmap; - } - - uart->rx_irq = platform_get_irq(pdev, 1); - if (uart->rx_irq < 0) { - dev_err(&pdev->dev, "No uart RX IRQ specified\n"); - ret = -ENOENT; - goto out_error_unmap; - } - uart->port.irq = uart->rx_irq; - - uart->status_irq = platform_get_irq(pdev, 2); - if (uart->status_irq < 0) { - dev_err(&pdev->dev, "No uart status IRQ specified\n"); - ret = -ENOENT; - goto out_error_unmap; - } - -#ifdef CONFIG_SERIAL_BFIN_DMA - spin_lock_init(&uart->rx_lock); - uart->tx_done = 1; - uart->tx_count = 0; - - res = platform_get_resource(pdev, IORESOURCE_DMA, 0); - if (res == NULL) { - dev_err(&pdev->dev, "No uart TX DMA channel specified\n"); - ret = -ENOENT; - goto out_error_unmap; - } - uart->tx_dma_channel = res->start; - - res = platform_get_resource(pdev, IORESOURCE_DMA, 1); - if (res == NULL) { - dev_err(&pdev->dev, "No uart RX DMA channel specified\n"); - ret = -ENOENT; - goto out_error_unmap; - } - uart->rx_dma_channel = res->start; - - timer_setup(&uart->rx_dma_timer, bfin_serial_rx_dma_timeout, 0); -#endif - -#if defined(SERIAL_BFIN_CTSRTS) || \ - defined(SERIAL_BFIN_HARD_CTSRTS) - res = platform_get_resource(pdev, IORESOURCE_IO, 0); - if (res == NULL) - uart->cts_pin = -1; - else - uart->cts_pin = res->start; - - res = platform_get_resource(pdev, IORESOURCE_IO, 1); - if (res == NULL) - uart->rts_pin = -1; - else - uart->rts_pin = res->start; -#endif - } - -#ifdef CONFIG_SERIAL_BFIN_CONSOLE - if (!is_early_platform_device(pdev)) { -#endif - uart = bfin_serial_ports[pdev->id]; - uart->port.dev = &pdev->dev; - dev_set_drvdata(&pdev->dev, uart); - ret = uart_add_one_port(&bfin_serial_reg, &uart->port); -#ifdef CONFIG_SERIAL_BFIN_CONSOLE - } -#endif - - if (!ret) - return 0; - - if (uart) { -out_error_unmap: - iounmap(uart->port.membase); -out_error_free_peripherals: - peripheral_free_list(dev_get_platdata(&pdev->dev)); -out_error_free_mem: - kfree(uart); - bfin_serial_ports[pdev->id] = NULL; - } - - return ret; -} - -static int bfin_serial_remove(struct platform_device *pdev) -{ - struct bfin_serial_port *uart = platform_get_drvdata(pdev); - - dev_set_drvdata(&pdev->dev, NULL); - - if (uart) { - uart_remove_one_port(&bfin_serial_reg, &uart->port); - iounmap(uart->port.membase); - peripheral_free_list(dev_get_platdata(&pdev->dev)); - kfree(uart); - bfin_serial_ports[pdev->id] = NULL; - } - - return 0; -} - -static struct platform_driver bfin_serial_driver = { - .probe = bfin_serial_probe, - .remove = bfin_serial_remove, - .suspend = bfin_serial_suspend, - .resume = bfin_serial_resume, - .driver = { - .name = DRIVER_NAME, - }, -}; - -#if defined(CONFIG_SERIAL_BFIN_CONSOLE) -static struct early_platform_driver early_bfin_serial_driver __initdata = { - .class_str = CLASS_BFIN_CONSOLE, - .pdrv = &bfin_serial_driver, - .requested_id = EARLY_PLATFORM_ID_UNSET, -}; - -static int __init bfin_serial_rs_console_init(void) -{ - early_platform_driver_register(&early_bfin_serial_driver, DRIVER_NAME); - - early_platform_driver_probe(CLASS_BFIN_CONSOLE, BFIN_UART_NR_PORTS, 0); - - register_console(&bfin_serial_console); - - return 0; -} -console_initcall(bfin_serial_rs_console_init); -#endif - -#ifdef CONFIG_EARLY_PRINTK -/* - * Memory can't be allocated dynamically during earlyprink init stage. - * So, do individual probe for earlyprink with a static uart port variable. - */ -static int bfin_earlyprintk_probe(struct platform_device *pdev) -{ - struct resource *res; - int ret; - - if (pdev->id < 0 || pdev->id >= BFIN_UART_NR_PORTS) { - dev_err(&pdev->dev, "Wrong earlyprintk platform device id.\n"); - return -ENOENT; - } - - ret = peripheral_request_list(dev_get_platdata(&pdev->dev), - DRIVER_NAME); - if (ret) { - dev_err(&pdev->dev, - "fail to request bfin serial peripherals\n"); - return ret; - } - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (res == NULL) { - dev_err(&pdev->dev, "Cannot get IORESOURCE_MEM\n"); - ret = -ENOENT; - goto out_error_free_peripherals; - } - - bfin_earlyprintk_port.port.membase = ioremap(res->start, - resource_size(res)); - if (!bfin_earlyprintk_port.port.membase) { - dev_err(&pdev->dev, "Cannot map uart IO\n"); - ret = -ENXIO; - goto out_error_free_peripherals; - } - bfin_earlyprintk_port.port.mapbase = res->start; - bfin_earlyprintk_port.port.line = pdev->id; - bfin_earlyprintk_port.port.uartclk = get_sclk(); - bfin_earlyprintk_port.port.fifosize = BFIN_UART_TX_FIFO_SIZE; - spin_lock_init(&bfin_earlyprintk_port.port.lock); - - return 0; - -out_error_free_peripherals: - peripheral_free_list(dev_get_platdata(&pdev->dev)); - - return ret; -} - -static struct platform_driver bfin_earlyprintk_driver = { - .probe = bfin_earlyprintk_probe, - .driver = { - .name = DRIVER_NAME, - .owner = THIS_MODULE, - }, -}; - -static struct early_platform_driver early_bfin_earlyprintk_driver __initdata = { - .class_str = CLASS_BFIN_EARLYPRINTK, - .pdrv = &bfin_earlyprintk_driver, - .requested_id = EARLY_PLATFORM_ID_UNSET, -}; - -struct console __init *bfin_earlyserial_init(unsigned int port, - unsigned int cflag) -{ - struct ktermios t; - char port_name[20]; - - if (port < 0 || port >= BFIN_UART_NR_PORTS) - return NULL; - - /* - * Only probe resource of the given port in earlyprintk boot arg. - * The expected port id should be indicated in port name string. - */ - snprintf(port_name, 20, DRIVER_NAME ".%d", port); - early_platform_driver_register(&early_bfin_earlyprintk_driver, - port_name); - early_platform_driver_probe(CLASS_BFIN_EARLYPRINTK, 1, 0); - - if (!bfin_earlyprintk_port.port.membase) - return NULL; - -#ifdef CONFIG_SERIAL_BFIN_CONSOLE - /* - * If we are using early serial, don't let the normal console rewind - * log buffer, since that causes things to be printed multiple times - */ - bfin_serial_console.flags &= ~CON_PRINTBUFFER; -#endif - - bfin_early_serial_console.index = port; - t.c_cflag = cflag; - t.c_iflag = 0; - t.c_oflag = 0; - t.c_lflag = ICANON; - t.c_line = port; - bfin_serial_set_termios(&bfin_earlyprintk_port.port, &t, &t); - - return &bfin_early_serial_console; -} -#endif /* CONFIG_EARLY_PRINTK */ - -static int __init bfin_serial_init(void) -{ - int ret; - - pr_info("Blackfin serial driver\n"); - - ret = uart_register_driver(&bfin_serial_reg); - if (ret) { - pr_err("failed to register %s:%d\n", - bfin_serial_reg.driver_name, ret); - } - - ret = platform_driver_register(&bfin_serial_driver); - if (ret) { - pr_err("fail to register bfin uart\n"); - uart_unregister_driver(&bfin_serial_reg); - } - - return ret; -} - -static void __exit bfin_serial_exit(void) -{ - platform_driver_unregister(&bfin_serial_driver); - uart_unregister_driver(&bfin_serial_reg); -} - - -module_init(bfin_serial_init); -module_exit(bfin_serial_exit); - -MODULE_AUTHOR("Sonic Zhang, Aubrey Li"); -MODULE_DESCRIPTION("Blackfin generic serial port driver"); -MODULE_LICENSE("GPL"); -MODULE_ALIAS_CHARDEV_MAJOR(BFIN_SERIAL_MAJOR); -MODULE_ALIAS("platform:bfin-uart"); |