diff options
Diffstat (limited to 'drivers/tty/serial/68328serial.h')
| -rw-r--r-- | drivers/tty/serial/68328serial.h | 186 |
1 files changed, 0 insertions, 186 deletions
diff --git a/drivers/tty/serial/68328serial.h b/drivers/tty/serial/68328serial.h deleted file mode 100644 index 3d2faabd766f..000000000000 --- a/drivers/tty/serial/68328serial.h +++ /dev/null @@ -1,186 +0,0 @@ -/* 68328serial.h: Definitions for the mc68328 serial driver. - * - * Copyright (C) 1995 David S. Miller <davem@caip.rutgers.edu> - * Copyright (C) 1998 Kenneth Albanowski <kjahds@kjahds.com> - * Copyright (C) 1998, 1999 D. Jeff Dionne <jeff@uclinux.org> - * Copyright (C) 1999 Vladimir Gurevich <vgurevic@cisco.com> - * - * VZ Support/Fixes Evan Stawnyczy <e@lineo.ca> - */ - -#ifndef _MC683XX_SERIAL_H -#define _MC683XX_SERIAL_H - - -struct serial_struct { - int type; - int line; - int port; - int irq; - int flags; - int xmit_fifo_size; - int custom_divisor; - int baud_base; - unsigned short close_delay; - char reserved_char[2]; - int hub6; /* FIXME: We don't have AT&T Hub6 boards! */ - unsigned short closing_wait; /* time to wait before closing */ - unsigned short closing_wait2; /* no longer used... */ - int reserved[4]; -}; - -/* - * For the close wait times, 0 means wait forever for serial port to - * flush its output. 65535 means don't wait at all. - */ -#define S_CLOSING_WAIT_INF 0 -#define S_CLOSING_WAIT_NONE 65535 - -/* - * Definitions for S_struct (and serial_struct) flags field - */ -#define S_HUP_NOTIFY 0x0001 /* Notify getty on hangups and closes - on the callout port */ -#define S_FOURPORT 0x0002 /* Set OU1, OUT2 per AST Fourport settings */ -#define S_SAK 0x0004 /* Secure Attention Key (Orange book) */ -#define S_SPLIT_TERMIOS 0x0008 /* Separate termios for dialin/callout */ - -#define S_SPD_MASK 0x0030 -#define S_SPD_HI 0x0010 /* Use 56000 instead of 38400 bps */ - -#define S_SPD_VHI 0x0020 /* Use 115200 instead of 38400 bps */ -#define S_SPD_CUST 0x0030 /* Use user-specified divisor */ - -#define S_SKIP_TEST 0x0040 /* Skip UART test during autoconfiguration */ -#define S_AUTO_IRQ 0x0080 /* Do automatic IRQ during autoconfiguration */ -#define S_SESSION_LOCKOUT 0x0100 /* Lock out cua opens based on session */ -#define S_PGRP_LOCKOUT 0x0200 /* Lock out cua opens based on pgrp */ -#define S_CALLOUT_NOHUP 0x0400 /* Don't do hangups for cua device */ - -#define S_FLAGS 0x0FFF /* Possible legal S flags */ -#define S_USR_MASK 0x0430 /* Legal flags that non-privileged - * users can set or reset */ - -/* Internal flags used only by kernel/chr_drv/serial.c */ -#define S_INITIALIZED 0x80000000 /* Serial port was initialized */ -#define S_CALLOUT_ACTIVE 0x40000000 /* Call out device is active */ -#define S_NORMAL_ACTIVE 0x20000000 /* Normal device is active */ -#define S_BOOT_AUTOCONF 0x10000000 /* Autoconfigure port on bootup */ -#define S_CLOSING 0x08000000 /* Serial port is closing */ -#define S_CTS_FLOW 0x04000000 /* Do CTS flow control */ -#define S_CHECK_CD 0x02000000 /* i.e., CLOCAL */ - -/* Software state per channel */ - -#ifdef __KERNEL__ - -/* - * I believe this is the optimal setting that reduces the number of interrupts. - * At high speeds the output might become a little "bursted" (use USTCNT_TXHE - * if that bothers you), but in most cases it will not, since we try to - * transmit characters every time rs_interrupt is called. Thus, quite often - * you'll see that a receive interrupt occures before the transmit one. - * -- Vladimir Gurevich - */ -#define USTCNT_TX_INTR_MASK (USTCNT_TXEE) - -/* - * 68328 and 68EZ328 UARTS are a little bit different. EZ328 has special - * "Old data interrupt" which occures whenever the data stay in the FIFO - * longer than 30 bits time. This allows us to use FIFO without compromising - * latency. '328 does not have this feature and without the real 328-based - * board I would assume that RXRE is the safest setting. - * - * For EZ328 I use RXHE (Half empty) interrupt to reduce the number of - * interrupts. RXFE (receive queue full) causes the system to lose data - * at least at 115200 baud - * - * If your board is busy doing other stuff, you might consider to use - * RXRE (data ready intrrupt) instead. - * - * The other option is to make these INTR masks run-time configurable, so - * that people can dynamically adapt them according to the current usage. - * -- Vladimir Gurevich - */ - -/* (es) */ -#if defined(CONFIG_M68EZ328) || defined(CONFIG_M68VZ328) -#define USTCNT_RX_INTR_MASK (USTCNT_RXHE | USTCNT_ODEN) -#elif defined(CONFIG_M68328) -#define USTCNT_RX_INTR_MASK (USTCNT_RXRE) -#else -#error Please, define the Rx interrupt events for your CPU -#endif -/* (/es) */ - -/* - * This is our internal structure for each serial port's state. - * - * Many fields are paralleled by the structure used by the serial_struct - * structure. - * - * For definitions of the flags field, see tty.h - */ - -struct m68k_serial { - char soft_carrier; /* Use soft carrier on this channel */ - char break_abort; /* Is serial console in, so process brk/abrt */ - char is_cons; /* Is this our console. */ - - /* We need to know the current clock divisor - * to read the bps rate the chip has currently - * loaded. - */ - unsigned char clk_divisor; /* May be 1, 16, 32, or 64 */ - int baud; - int magic; - int baud_base; - int port; - int irq; - int flags; /* defined in tty.h */ - int type; /* UART type */ - struct tty_struct *tty; - int read_status_mask; - int ignore_status_mask; - int timeout; - int xmit_fifo_size; - int custom_divisor; - int x_char; /* xon/xoff character */ - int close_delay; - unsigned short closing_wait; - unsigned short closing_wait2; - unsigned long event; - unsigned long last_active; - int line; - int count; /* # of fd on device */ - int blocked_open; /* # of blocked opens */ - unsigned char *xmit_buf; - int xmit_head; - int xmit_tail; - int xmit_cnt; - wait_queue_head_t open_wait; - wait_queue_head_t close_wait; -}; - - -#define SERIAL_MAGIC 0x5301 - -/* - * The size of the serial xmit buffer is 1 page, or 4096 bytes - */ -#define SERIAL_XMIT_SIZE 4096 - -/* - * Events are used to schedule things to happen at timer-interrupt - * time, instead of at rs interrupt time. - */ -#define RS_EVENT_WRITE_WAKEUP 0 - -/* - * Define the number of ports supported and their irqs. - */ -#define NR_PORTS 1 -#define UART_IRQ_DEFNS {UART_IRQ_NUM} - -#endif /* __KERNEL__ */ -#endif /* !(_MC683XX_SERIAL_H) */ |