1 files changed, 374 insertions, 0 deletions
diff --git a/drivers/net/wireless/intel/iwlwifi/pcie/trans-gen2.c b/drivers/net/wireless/intel/iwlwifi/pcie/trans-gen2.c
new file mode 100644
index 000000000000..ac60a282d6de
--- /dev/null
+++ b/drivers/net/wireless/intel/iwlwifi/pcie/trans-gen2.c
@@ -0,0 +1,374 @@
+/******************************************************************************
+ *
+ * This file is provided under a dual BSD/GPLv2 license.  When using or
+ * redistributing this file, you may do so under either license.
+ *
+ * GPL LICENSE SUMMARY
+ *
+ * Copyright(c) 2017 Intel Deutschland GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * BSD LICENSE
+ *
+ * Copyright(c) 2017 Intel Deutschland GmbH
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ *  * Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ *  * Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ *  * Neither the name Intel Corporation nor the names of its
+ *    contributors may be used to endorse or promote products derived
+ *    from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *****************************************************************************/
+#include "iwl-trans.h"
+#include "iwl-context-info.h"
+#include "internal.h"
+
+/*
+ * Start up NIC's basic functionality after it has been reset
+ * (e.g. after platform boot, or shutdown via iwl_pcie_apm_stop())
+ * NOTE:  This does not load uCode nor start the embedded processor
+ */
+static int iwl_pcie_gen2_apm_init(struct iwl_trans *trans)
+{
+	int ret = 0;
+
+	IWL_DEBUG_INFO(trans, "Init card's basic functions\n");
+
+	/*
+	 * Use "set_bit" below rather than "write", to preserve any hardware
+	 * bits already set by default after reset.
+	 */
+
+	/*
+	 * Disable L0s without affecting L1;
+	 * don't wait for ICH L0s (ICH bug W/A)
+	 */
+	iwl_set_bit(trans, CSR_GIO_CHICKEN_BITS,
+		    CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX);
+
+	/* Set FH wait threshold to maximum (HW error during stress W/A) */
+	iwl_set_bit(trans, CSR_DBG_HPET_MEM_REG, CSR_DBG_HPET_MEM_REG_VAL);
+
+	/*
+	 * Enable HAP INTA (interrupt from management bus) to
+	 * wake device's PCI Express link L1a -> L0s
+	 */
+	iwl_set_bit(trans, CSR_HW_IF_CONFIG_REG,
+		    CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A);
+
+	iwl_pcie_apm_config(trans);
+
+	/*
+	 * Set "initialization complete" bit to move adapter from
+	 * D0U* --> D0A* (powered-up active) state.
+	 */
+	iwl_set_bit(trans, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE);
+
+	/*
+	 * Wait for clock stabilization; once stabilized, access to
+	 * device-internal resources is supported, e.g. iwl_write_prph()
+	 * and accesses to uCode SRAM.
+	 */
+	ret = iwl_poll_bit(trans, CSR_GP_CNTRL,
+			   CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY,
+			   CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY, 25000);
+	if (ret < 0) {
+		IWL_DEBUG_INFO(trans, "Failed to init the card\n");
+		return ret;
+	}
+
+	set_bit(STATUS_DEVICE_ENABLED, &trans->status);
+
+	return 0;
+}
+
+static void iwl_pcie_gen2_apm_stop(struct iwl_trans *trans, bool op_mode_leave)
+{
+	IWL_DEBUG_INFO(trans, "Stop card, put in low power state\n");
+
+	if (op_mode_leave) {
+		if (!test_bit(STATUS_DEVICE_ENABLED, &trans->status))
+			iwl_pcie_gen2_apm_init(trans);
+
+		/* inform ME that we are leaving */
+		iwl_set_bit(trans, CSR_DBG_LINK_PWR_MGMT_REG,
+			    CSR_RESET_LINK_PWR_MGMT_DISABLED);
+		iwl_set_bit(trans, CSR_HW_IF_CONFIG_REG,
+			    CSR_HW_IF_CONFIG_REG_PREPARE |
+			    CSR_HW_IF_CONFIG_REG_ENABLE_PME);
+		mdelay(1);
+		iwl_clear_bit(trans, CSR_DBG_LINK_PWR_MGMT_REG,
+			      CSR_RESET_LINK_PWR_MGMT_DISABLED);
+		mdelay(5);
+	}
+
+	clear_bit(STATUS_DEVICE_ENABLED, &trans->status);
+
+	/* Stop device's DMA activity */
+	iwl_pcie_apm_stop_master(trans);
+
+	/* Reset the entire device */
+	iwl_set_bit(trans, CSR_RESET, CSR_RESET_REG_FLAG_SW_RESET);
+	usleep_range(1000, 2000);
+
+	/*
+	 * Clear "initialization complete" bit to move adapter from
+	 * D0A* (powered-up Active) --> D0U* (Uninitialized) state.
+	 */
+	iwl_clear_bit(trans, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE);
+}
+
+void _iwl_trans_pcie_gen2_stop_device(struct iwl_trans *trans, bool low_power)
+{
+	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
+	bool hw_rfkill, was_hw_rfkill;
+
+	lockdep_assert_held(&trans_pcie->mutex);
+
+	if (trans_pcie->is_down)
+		return;
+
+	trans_pcie->is_down = true;
+
+	was_hw_rfkill = iwl_is_rfkill_set(trans);
+
+	/* tell the device to stop sending interrupts */
+	iwl_disable_interrupts(trans);
+
+	/* device going down, Stop using ICT table */
+	iwl_pcie_disable_ict(trans);
+
+	/*
+	 * If a HW restart happens during firmware loading,
+	 * then the firmware loading might call this function
+	 * and later it might be called again due to the
+	 * restart. So don't process again if the device is
+	 * already dead.
+	 */
+	if (test_and_clear_bit(STATUS_DEVICE_ENABLED, &trans->status)) {
+		IWL_DEBUG_INFO(trans,
+			       "DEVICE_ENABLED bit was set and is now cleared\n");
+		iwl_pcie_gen2_tx_stop(trans);
+		iwl_pcie_rx_stop(trans);
+	}
+
+	iwl_pcie_ctxt_info_free_paging(trans);
+	iwl_pcie_ctxt_info_free(trans);
+
+	/* Make sure (redundant) we've released our request to stay awake */
+	iwl_clear_bit(trans, CSR_GP_CNTRL,
+		      CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ);
+
+	/* Stop the device, and put it in low power state */
+	iwl_pcie_gen2_apm_stop(trans, false);
+
+	/* stop and reset the on-board processor */
+	iwl_write32(trans, CSR_RESET, CSR_RESET_REG_FLAG_SW_RESET);
+	usleep_range(1000, 2000);
+
+	/*
+	 * Upon stop, the IVAR table gets erased, so msi-x won't
+	 * work. This causes a bug in RF-KILL flows, since the interrupt
+	 * that enables radio won't fire on the correct irq, and the
+	 * driver won't be able to handle the interrupt.
+	 * Configure the IVAR table again after reset.
+	 */
+	iwl_pcie_conf_msix_hw(trans_pcie);
+
+	/*
+	 * Upon stop, the APM issues an interrupt if HW RF kill is set.
+	 * This is a bug in certain verions of the hardware.
+	 * Certain devices also keep sending HW RF kill interrupt all
+	 * the time, unless the interrupt is ACKed even if the interrupt
+	 * should be masked. Re-ACK all the interrupts here.
+	 */
+	iwl_disable_interrupts(trans);
+
+	/* clear all status bits */
+	clear_bit(STATUS_SYNC_HCMD_ACTIVE, &trans->status);
+	clear_bit(STATUS_INT_ENABLED, &trans->status);
+	clear_bit(STATUS_TPOWER_PMI, &trans->status);
+	clear_bit(STATUS_RFKILL, &trans->status);
+
+	/*
+	 * Even if we stop the HW, we still want the RF kill
+	 * interrupt
+	 */
+	iwl_enable_rfkill_int(trans);
+
+	/*
+	 * Check again since the RF kill state may have changed while
+	 * all the interrupts were disabled, in this case we couldn't
+	 * receive the RF kill interrupt and update the state in the
+	 * op_mode.
+	 * Don't call the op_mode if the rkfill state hasn't changed.
+	 * This allows the op_mode to call stop_device from the rfkill
+	 * notification without endless recursion. Under very rare
+	 * circumstances, we might have a small recursion if the rfkill
+	 * state changed exactly now while we were called from stop_device.
+	 * This is very unlikely but can happen and is supported.
+	 */
+	hw_rfkill = iwl_is_rfkill_set(trans);
+	if (hw_rfkill)
+		set_bit(STATUS_RFKILL, &trans->status);
+	else
+		clear_bit(STATUS_RFKILL, &trans->status);
+	if (hw_rfkill != was_hw_rfkill)
+		iwl_trans_pcie_rf_kill(trans, hw_rfkill);
+
+	/* re-take ownership to prevent other users from stealing the device */
+	iwl_pcie_prepare_card_hw(trans);
+}
+
+void iwl_trans_pcie_gen2_stop_device(struct iwl_trans *trans, bool low_power)
+{
+	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
+
+	mutex_lock(&trans_pcie->mutex);
+	_iwl_trans_pcie_gen2_stop_device(trans, low_power);
+	mutex_unlock(&trans_pcie->mutex);
+}
+
+static int iwl_pcie_gen2_nic_init(struct iwl_trans *trans)
+{
+	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
+
+	/* TODO: most of the logic can be removed in A0 - but not in Z0 */
+	spin_lock(&trans_pcie->irq_lock);
+	iwl_pcie_gen2_apm_init(trans);
+	spin_unlock(&trans_pcie->irq_lock);
+
+	iwl_op_mode_nic_config(trans->op_mode);
+
+	/* Allocate the RX queue, or reset if it is already allocated */
+	if (iwl_pcie_gen2_rx_init(trans))
+		return -ENOMEM;
+
+	/* Allocate or reset and init all Tx and Command queues */
+	if (iwl_pcie_gen2_tx_init(trans))
+		return -ENOMEM;
+
+	/* enable shadow regs in HW */
+	iwl_set_bit(trans, CSR_MAC_SHADOW_REG_CTRL, 0x800FFFFF);
+	IWL_DEBUG_INFO(trans, "Enabling shadow registers in device\n");
+
+	return 0;
+}
+
+void iwl_trans_pcie_gen2_fw_alive(struct iwl_trans *trans, u32 scd_addr)
+{
+	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
+
+	iwl_pcie_reset_ict(trans);
+
+	/* make sure all queue are not stopped/used */
+	memset(trans_pcie->queue_stopped, 0, sizeof(trans_pcie->queue_stopped));
+	memset(trans_pcie->queue_used, 0, sizeof(trans_pcie->queue_used));
+
+	/* now that we got alive we can free the fw image & the context info.
+	 * paging memory cannot be freed included since FW will still use it
+	 */
+	iwl_pcie_ctxt_info_free(trans);
+}
+
+int iwl_trans_pcie_gen2_start_fw(struct iwl_trans *trans,
+				 const struct fw_img *fw, bool run_in_rfkill)
+{
+	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
+	bool hw_rfkill;
+	int ret;
+
+	/* This may fail if AMT took ownership of the device */
+	if (iwl_pcie_prepare_card_hw(trans)) {
+		IWL_WARN(trans, "Exit HW not ready\n");
+		ret = -EIO;
+		goto out;
+	}
+
+	iwl_enable_rfkill_int(trans);
+
+	iwl_write32(trans, CSR_INT, 0xFFFFFFFF);
+
+	/*
+	 * We enabled the RF-Kill interrupt and the handler may very
+	 * well be running. Disable the interrupts to make sure no other
+	 * interrupt can be fired.
+	 */
+	iwl_disable_interrupts(trans);
+
+	/* Make sure it finished running */
+	iwl_pcie_synchronize_irqs(trans);
+
+	mutex_lock(&trans_pcie->mutex);
+
+	/* If platform's RF_KILL switch is NOT set to KILL */
+	hw_rfkill = iwl_trans_check_hw_rf_kill(trans);
+	if (hw_rfkill && !run_in_rfkill) {
+		ret = -ERFKILL;
+		goto out;
+	}
+
+	/* Someone called stop_device, don't try to start_fw */
+	if (trans_pcie->is_down) {
+		IWL_WARN(trans,
+			 "Can't start_fw since the HW hasn't been started\n");
+		ret = -EIO;
+		goto out;
+	}
+
+	/* make sure rfkill handshake bits are cleared */
+	iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
+	iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR,
+		    CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);
+
+	/* clear (again), then enable host interrupts */
+	iwl_write32(trans, CSR_INT, 0xFFFFFFFF);
+
+	ret = iwl_pcie_gen2_nic_init(trans);
+	if (ret) {
+		IWL_ERR(trans, "Unable to init nic\n");
+		goto out;
+	}
+
+	ret = iwl_pcie_ctxt_info_init(trans, fw);
+	if (ret)
+		goto out;
+
+	/* re-check RF-Kill state since we may have missed the interrupt */
+	hw_rfkill = iwl_trans_check_hw_rf_kill(trans);
+	if (hw_rfkill && !run_in_rfkill)
+		ret = -ERFKILL;
+
+out:
+	mutex_unlock(&trans_pcie->mutex);
+	return ret;
+}