diff options
Diffstat (limited to 'drivers/net/phy/bcm7xxx.c')
| -rw-r--r-- | drivers/net/phy/bcm7xxx.c | 136 |
1 files changed, 31 insertions, 105 deletions
diff --git a/drivers/net/phy/bcm7xxx.c b/drivers/net/phy/bcm7xxx.c index 6b701b3ded74..03d4809a9126 100644 --- a/drivers/net/phy/bcm7xxx.c +++ b/drivers/net/phy/bcm7xxx.c @@ -12,12 +12,12 @@ #include <linux/module.h> #include <linux/phy.h> #include <linux/delay.h> +#include "bcm-phy-lib.h" #include <linux/bitops.h> #include <linux/brcmphy.h> #include <linux/mdio.h> /* Broadcom BCM7xxx internal PHY registers */ -#define MII_BCM7XXX_CHANNEL_WIDTH 0x2000 /* 40nm only register definitions */ #define MII_BCM7XXX_100TX_AUX_CTL 0x10 @@ -25,7 +25,6 @@ #define MII_BCM7XXX_100TX_DISC 0x14 #define MII_BCM7XXX_AUX_MODE 0x1d #define MII_BCM7XX_64CLK_MDIO BIT(12) -#define MII_BCM7XXX_CORE_BASE1E 0x1e #define MII_BCM7XXX_TEST 0x1f #define MII_BCM7XXX_SHD_MODE_2 BIT(2) @@ -46,39 +45,13 @@ #define AFE_VDAC_OTHERS_0 MISC_ADDR(0x39, 3) #define AFE_HPF_TRIM_OTHERS MISC_ADDR(0x3a, 0) -#define CORE_EXPB0 0xb0 - -static void phy_write_exp(struct phy_device *phydev, - u16 reg, u16 value) -{ - phy_write(phydev, MII_BCM54XX_EXP_SEL, MII_BCM54XX_EXP_SEL_ER | reg); - phy_write(phydev, MII_BCM54XX_EXP_DATA, value); -} - -static void phy_write_misc(struct phy_device *phydev, - u16 reg, u16 chl, u16 value) -{ - int tmp; - - phy_write(phydev, MII_BCM54XX_AUX_CTL, MII_BCM54XX_AUXCTL_SHDWSEL_MISC); - - tmp = phy_read(phydev, MII_BCM54XX_AUX_CTL); - tmp |= MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA; - phy_write(phydev, MII_BCM54XX_AUX_CTL, tmp); - - tmp = (chl * MII_BCM7XXX_CHANNEL_WIDTH) | reg; - phy_write(phydev, MII_BCM54XX_EXP_SEL, tmp); - - phy_write(phydev, MII_BCM54XX_EXP_DATA, value); -} - static void r_rc_cal_reset(struct phy_device *phydev) { /* Reset R_CAL/RC_CAL Engine */ - phy_write_exp(phydev, 0x00b0, 0x0010); + bcm_phy_write_exp(phydev, 0x00b0, 0x0010); /* Disable Reset R_AL/RC_CAL Engine */ - phy_write_exp(phydev, 0x00b0, 0x0000); + bcm_phy_write_exp(phydev, 0x00b0, 0x0000); } static int bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev) @@ -86,38 +59,38 @@ static int bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev) /* Increase VCO range to prevent unlocking problem of PLL at low * temp */ - phy_write_misc(phydev, PLL_PLLCTRL_1, 0x0048); + bcm_phy_write_misc(phydev, PLL_PLLCTRL_1, 0x0048); /* Change Ki to 011 */ - phy_write_misc(phydev, PLL_PLLCTRL_2, 0x021b); + bcm_phy_write_misc(phydev, PLL_PLLCTRL_2, 0x021b); /* Disable loading of TVCO buffer to bandgap, set bandgap trim * to 111 */ - phy_write_misc(phydev, PLL_PLLCTRL_4, 0x0e20); + bcm_phy_write_misc(phydev, PLL_PLLCTRL_4, 0x0e20); /* Adjust bias current trim by -3 */ - phy_write_misc(phydev, DSP_TAP10, 0x690b); + bcm_phy_write_misc(phydev, DSP_TAP10, 0x690b); /* Switch to CORE_BASE1E */ - phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0xd); + phy_write(phydev, MII_BRCM_CORE_BASE1E, 0xd); r_rc_cal_reset(phydev); /* write AFE_RXCONFIG_0 */ - phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb19); + bcm_phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb19); /* write AFE_RXCONFIG_1 */ - phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9a3f); + bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9a3f); /* write AFE_RX_LP_COUNTER */ - phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0); + bcm_phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0); /* write AFE_HPF_TRIM_OTHERS */ - phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x000b); + bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x000b); /* write AFTE_TX_CONFIG */ - phy_write_misc(phydev, AFE_TX_CONFIG, 0x0800); + bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x0800); return 0; } @@ -125,36 +98,36 @@ static int bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev) static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev) { /* AFE_RXCONFIG_0 */ - phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15); + bcm_phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15); /* AFE_RXCONFIG_1 */ - phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f); + bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f); /* AFE_RXCONFIG_2, set rCal offset for HT=0 code and LT=-2 code */ - phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003); + bcm_phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003); /* AFE_RX_LP_COUNTER, set RX bandwidth to maximum */ - phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0); + bcm_phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0); /* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall time */ - phy_write_misc(phydev, AFE_TX_CONFIG, 0x431); + bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431); /* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */ - phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da); + bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da); /* AFE_VDAC_OTHERS_0, set 1000BT Cidac=010 for all ports */ - phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020); + bcm_phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020); /* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal * offset for HT=0 code */ - phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3); + bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3); /* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */ - phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010); + phy_write(phydev, MII_BRCM_CORE_BASE1E, 0x0010); /* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */ - phy_write_misc(phydev, DSP_TAP10, 0x011b); + bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b); /* Reset R_CAL/RC_CAL engine */ r_rc_cal_reset(phydev); @@ -165,24 +138,24 @@ static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev) static int bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device *phydev) { /* AFE_RXCONFIG_1, provide more margin for INL/DNL measurement */ - phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f); + bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f); /* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall time */ - phy_write_misc(phydev, AFE_TX_CONFIG, 0x431); + bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431); /* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */ - phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da); + bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da); /* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal * offset for HT=0 code */ - phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3); + bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3); /* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */ - phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010); + phy_write(phydev, MII_BRCM_CORE_BASE1E, 0x0010); /* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */ - phy_write_misc(phydev, DSP_TAP10, 0x011b); + bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b); /* Reset R_CAL/RC_CAL engine */ r_rc_cal_reset(phydev); @@ -190,53 +163,6 @@ static int bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device *phydev) return 0; } -static int bcm7xxx_apd_enable(struct phy_device *phydev) -{ - int val; - - /* Enable powering down of the DLL during auto-power down */ - val = bcm54xx_shadow_read(phydev, BCM54XX_SHD_SCR3); - if (val < 0) - return val; - - val |= BCM54XX_SHD_SCR3_DLLAPD_DIS; - bcm54xx_shadow_write(phydev, BCM54XX_SHD_SCR3, val); - - /* Enable auto-power down */ - val = bcm54xx_shadow_read(phydev, BCM54XX_SHD_APD); - if (val < 0) - return val; - - val |= BCM54XX_SHD_APD_EN; - return bcm54xx_shadow_write(phydev, BCM54XX_SHD_APD, val); -} - -static int bcm7xxx_eee_enable(struct phy_device *phydev) -{ - int val; - - val = phy_read_mmd_indirect(phydev, BRCM_CL45VEN_EEE_CONTROL, - MDIO_MMD_AN, phydev->addr); - if (val < 0) - return val; - - /* Enable general EEE feature at the PHY level */ - val |= LPI_FEATURE_EN | LPI_FEATURE_EN_DIG1000X; - - phy_write_mmd_indirect(phydev, BRCM_CL45VEN_EEE_CONTROL, - MDIO_MMD_AN, phydev->addr, val); - - /* Advertise supported modes */ - val = phy_read_mmd_indirect(phydev, MDIO_AN_EEE_ADV, - MDIO_MMD_AN, phydev->addr); - - val |= (MDIO_AN_EEE_ADV_100TX | MDIO_AN_EEE_ADV_1000T); - phy_write_mmd_indirect(phydev, MDIO_AN_EEE_ADV, - MDIO_MMD_AN, phydev->addr, val); - - return 0; -} - static int bcm7xxx_28nm_config_init(struct phy_device *phydev) { u8 rev = PHY_BRCM_7XXX_REV(phydev->dev_flags); @@ -273,11 +199,11 @@ static int bcm7xxx_28nm_config_init(struct phy_device *phydev) if (ret) return ret; - ret = bcm7xxx_eee_enable(phydev); + ret = bcm_phy_enable_eee(phydev); if (ret) return ret; - return bcm7xxx_apd_enable(phydev); + return bcm_phy_enable_apd(phydev, true); } static int bcm7xxx_28nm_resume(struct phy_device *phydev) |