diff options
Diffstat (limited to 'drivers/net/phy/at803x.c')
-rw-r--r-- | drivers/net/phy/at803x.c | 105 |
1 files changed, 77 insertions, 28 deletions
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c index 222ccd9ecfce..1eb5d4fb8925 100644 --- a/drivers/net/phy/at803x.c +++ b/drivers/net/phy/at803x.c @@ -15,6 +15,15 @@ #include <linux/of_gpio.h> #include <linux/gpio/consumer.h> +#define AT803X_SPECIFIC_STATUS 0x11 +#define AT803X_SS_SPEED_MASK (3 << 14) +#define AT803X_SS_SPEED_1000 (2 << 14) +#define AT803X_SS_SPEED_100 (1 << 14) +#define AT803X_SS_SPEED_10 (0 << 14) +#define AT803X_SS_DUPLEX BIT(13) +#define AT803X_SS_SPEED_DUPLEX_RESOLVED BIT(11) +#define AT803X_SS_MDIX BIT(6) + #define AT803X_INTR_ENABLE 0x12 #define AT803X_INTR_ENABLE_AUTONEG_ERR BIT(15) #define AT803X_INTR_ENABLE_SPEED_CHANGED BIT(14) @@ -249,44 +258,24 @@ static int at803x_config_init(struct phy_device *phydev) { int ret; - ret = genphy_config_init(phydev); - if (ret < 0) - return ret; - /* The RX and TX delay default is: * after HW reset: RX delay enabled and TX delay disabled * after SW reset: RX delay enabled, while TX delay retains the * value before reset. - * - * So let's first disable the RX and TX delays in PHY and enable - * them based on the mode selected (this also takes care of RGMII - * mode where we expect delays to be disabled) */ - - ret = at803x_disable_rx_delay(phydev); - if (ret < 0) - return ret; - ret = at803x_disable_tx_delay(phydev); - if (ret < 0) - return ret; - if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || - phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) { - /* If RGMII_ID or RGMII_RXID are specified enable RX delay, - * otherwise keep it disabled - */ + phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) ret = at803x_enable_rx_delay(phydev); - if (ret < 0) - return ret; - } + else + ret = at803x_disable_rx_delay(phydev); + if (ret < 0) + return ret; if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || - phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) { - /* If RGMII_ID or RGMII_TXID are specified enable TX delay, - * otherwise keep it disabled - */ + phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) ret = at803x_enable_tx_delay(phydev); - } + else + ret = at803x_disable_tx_delay(phydev); return ret; } @@ -377,6 +366,64 @@ static int at803x_aneg_done(struct phy_device *phydev) return aneg_done; } +static int at803x_read_status(struct phy_device *phydev) +{ + int ss, err, old_link = phydev->link; + + /* Update the link, but return if there was an error */ + err = genphy_update_link(phydev); + if (err) + return err; + + /* why bother the PHY if nothing can have changed */ + if (phydev->autoneg == AUTONEG_ENABLE && old_link && phydev->link) + return 0; + + phydev->speed = SPEED_UNKNOWN; + phydev->duplex = DUPLEX_UNKNOWN; + phydev->pause = 0; + phydev->asym_pause = 0; + + err = genphy_read_lpa(phydev); + if (err < 0) + return err; + + /* Read the AT8035 PHY-Specific Status register, which indicates the + * speed and duplex that the PHY is actually using, irrespective of + * whether we are in autoneg mode or not. + */ + ss = phy_read(phydev, AT803X_SPECIFIC_STATUS); + if (ss < 0) + return ss; + + if (ss & AT803X_SS_SPEED_DUPLEX_RESOLVED) { + switch (ss & AT803X_SS_SPEED_MASK) { + case AT803X_SS_SPEED_10: + phydev->speed = SPEED_10; + break; + case AT803X_SS_SPEED_100: + phydev->speed = SPEED_100; + break; + case AT803X_SS_SPEED_1000: + phydev->speed = SPEED_1000; + break; + } + if (ss & AT803X_SS_DUPLEX) + phydev->duplex = DUPLEX_FULL; + else + phydev->duplex = DUPLEX_HALF; + if (ss & AT803X_SS_MDIX) + phydev->mdix = ETH_TP_MDI_X; + else + phydev->mdix = ETH_TP_MDI; + } + + if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete) + phy_resolve_aneg_pause(phydev); + + return 0; +} + static struct phy_driver at803x_driver[] = { { /* ATHEROS 8035 */ @@ -390,6 +437,7 @@ static struct phy_driver at803x_driver[] = { .suspend = at803x_suspend, .resume = at803x_resume, /* PHY_GBIT_FEATURES */ + .read_status = at803x_read_status, .ack_interrupt = at803x_ack_interrupt, .config_intr = at803x_config_intr, }, { @@ -419,6 +467,7 @@ static struct phy_driver at803x_driver[] = { .suspend = at803x_suspend, .resume = at803x_resume, /* PHY_GBIT_FEATURES */ + .read_status = at803x_read_status, .aneg_done = at803x_aneg_done, .ack_interrupt = &at803x_ack_interrupt, .config_intr = &at803x_config_intr, |