diff options
Diffstat (limited to 'drivers/net/e1000e/netdev.c')
| -rw-r--r-- | drivers/net/e1000e/netdev.c | 63 |
1 files changed, 35 insertions, 28 deletions
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index 16c193a6c95c..fad8f9ea0043 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -2769,25 +2769,38 @@ void e1000e_reset(struct e1000_adapter *adapter) /* * flow control settings * - * The high water mark must be low enough to fit two full frame + * The high water mark must be low enough to fit one full frame * (or the size used for early receive) above it in the Rx FIFO. * Set it to the lower of: * - 90% of the Rx FIFO size, and * - the full Rx FIFO size minus the early receive size (for parts * with ERT support assuming ERT set to E1000_ERT_2048), or - * - the full Rx FIFO size minus two full frames + * - the full Rx FIFO size minus one full frame */ - if ((adapter->flags & FLAG_HAS_ERT) && - (adapter->netdev->mtu > ETH_DATA_LEN)) - hwm = min(((pba << 10) * 9 / 10), - ((pba << 10) - (E1000_ERT_2048 << 3))); - else - hwm = min(((pba << 10) * 9 / 10), - ((pba << 10) - (2 * adapter->max_frame_size))); + if (hw->mac.type == e1000_pchlan) { + /* + * Workaround PCH LOM adapter hangs with certain network + * loads. If hangs persist, try disabling Tx flow control. + */ + if (adapter->netdev->mtu > ETH_DATA_LEN) { + fc->high_water = 0x3500; + fc->low_water = 0x1500; + } else { + fc->high_water = 0x5000; + fc->low_water = 0x3000; + } + } else { + if ((adapter->flags & FLAG_HAS_ERT) && + (adapter->netdev->mtu > ETH_DATA_LEN)) + hwm = min(((pba << 10) * 9 / 10), + ((pba << 10) - (E1000_ERT_2048 << 3))); + else + hwm = min(((pba << 10) * 9 / 10), + ((pba << 10) - adapter->max_frame_size)); - fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */ - fc->low_water = (fc->high_water - (2 * adapter->max_frame_size)); - fc->low_water &= E1000_FCRTL_RTL; /* 8-byte granularity */ + fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */ + fc->low_water = fc->high_water - 8; + } if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME) fc->pause_time = 0xFFFF; @@ -2813,6 +2826,10 @@ void e1000e_reset(struct e1000_adapter *adapter) if (mac->ops.init_hw(hw)) e_err("Hardware Error\n"); + /* additional part of the flow-control workaround above */ + if (hw->mac.type == e1000_pchlan) + ew32(FCRTV_PCH, 0x1000); + e1000_update_mng_vlan(adapter); /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */ @@ -3610,7 +3627,7 @@ static void e1000_watchdog_task(struct work_struct *work) case SPEED_100: txb2b = 0; netdev->tx_queue_len = 100; - /* maybe add some timeout factor ? */ + adapter->tx_timeout_factor = 10; break; } @@ -4288,8 +4305,10 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu) while (test_and_set_bit(__E1000_RESETTING, &adapter->state)) msleep(1); - /* e1000e_down has a dependency on max_frame_size */ + /* e1000e_down -> e1000e_reset dependent on max_frame_size & mtu */ adapter->max_frame_size = max_frame; + e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu); + netdev->mtu = new_mtu; if (netif_running(netdev)) e1000e_down(adapter); @@ -4319,9 +4338,6 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu) adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN; - e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu); - netdev->mtu = new_mtu; - if (netif_running(netdev)) e1000e_up(adapter); else @@ -4982,12 +4998,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev, goto err_pci_reg; /* AER (Advanced Error Reporting) hooks */ - err = pci_enable_pcie_error_reporting(pdev); - if (err) { - dev_err(&pdev->dev, "pci_enable_pcie_error_reporting failed " - "0x%x\n", err); - /* non-fatal, continue */ - } + pci_enable_pcie_error_reporting(pdev); pci_set_master(pdev); /* PCI config space info */ @@ -5263,7 +5274,6 @@ static void __devexit e1000_remove(struct pci_dev *pdev) { struct net_device *netdev = pci_get_drvdata(pdev); struct e1000_adapter *adapter = netdev_priv(netdev); - int err; /* * flush_scheduled work may reschedule our watchdog task, so @@ -5299,10 +5309,7 @@ static void __devexit e1000_remove(struct pci_dev *pdev) free_netdev(netdev); /* AER disable */ - err = pci_disable_pcie_error_reporting(pdev); - if (err) - dev_err(&pdev->dev, - "pci_disable_pcie_error_reporting failed 0x%x\n", err); + pci_disable_pcie_error_reporting(pdev); pci_disable_device(pdev); } |