diff options
Diffstat (limited to 'drivers/mtd/nand')
| -rw-r--r-- | drivers/mtd/nand/atmel_nand.c | 45 | ||||
| -rw-r--r-- | drivers/mtd/nand/gpmi-nand/gpmi-lib.c | 18 | ||||
| -rw-r--r-- | drivers/mtd/nand/nand_base.c | 2 |
3 files changed, 56 insertions, 9 deletions
diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c index 4dd056e2e16a..35b4fb55dbd6 100644 --- a/drivers/mtd/nand/atmel_nand.c +++ b/drivers/mtd/nand/atmel_nand.c @@ -161,6 +161,37 @@ static int atmel_nand_device_ready(struct mtd_info *mtd) !!host->board->rdy_pin_active_low; } +/* + * Minimal-overhead PIO for data access. + */ +static void atmel_read_buf8(struct mtd_info *mtd, u8 *buf, int len) +{ + struct nand_chip *nand_chip = mtd->priv; + + __raw_readsb(nand_chip->IO_ADDR_R, buf, len); +} + +static void atmel_read_buf16(struct mtd_info *mtd, u8 *buf, int len) +{ + struct nand_chip *nand_chip = mtd->priv; + + __raw_readsw(nand_chip->IO_ADDR_R, buf, len / 2); +} + +static void atmel_write_buf8(struct mtd_info *mtd, const u8 *buf, int len) +{ + struct nand_chip *nand_chip = mtd->priv; + + __raw_writesb(nand_chip->IO_ADDR_W, buf, len); +} + +static void atmel_write_buf16(struct mtd_info *mtd, const u8 *buf, int len) +{ + struct nand_chip *nand_chip = mtd->priv; + + __raw_writesw(nand_chip->IO_ADDR_W, buf, len / 2); +} + static void dma_complete_func(void *completion) { complete(completion); @@ -235,27 +266,33 @@ err_buf: static void atmel_read_buf(struct mtd_info *mtd, u8 *buf, int len) { struct nand_chip *chip = mtd->priv; + struct atmel_nand_host *host = chip->priv; if (use_dma && len > mtd->oobsize) /* only use DMA for bigger than oob size: better performances */ if (atmel_nand_dma_op(mtd, buf, len, 1) == 0) return; - /* if no DMA operation possible, use PIO */ - memcpy_fromio(buf, chip->IO_ADDR_R, len); + if (host->board->bus_width_16) + atmel_read_buf16(mtd, buf, len); + else + atmel_read_buf8(mtd, buf, len); } static void atmel_write_buf(struct mtd_info *mtd, const u8 *buf, int len) { struct nand_chip *chip = mtd->priv; + struct atmel_nand_host *host = chip->priv; if (use_dma && len > mtd->oobsize) /* only use DMA for bigger than oob size: better performances */ if (atmel_nand_dma_op(mtd, (void *)buf, len, 0) == 0) return; - /* if no DMA operation possible, use PIO */ - memcpy_toio(chip->IO_ADDR_W, buf, len); + if (host->board->bus_width_16) + atmel_write_buf16(mtd, buf, len); + else + atmel_write_buf8(mtd, buf, len); } /* diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c index 7f680420bfab..7db6555ed3ba 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c @@ -69,17 +69,19 @@ static int clear_poll_bit(void __iomem *addr, u32 mask) * [1] enable the module. * [2] reset the module. * - * In most of the cases, it's ok. But there is a hardware bug in the BCH block. + * In most of the cases, it's ok. + * But in MX23, there is a hardware bug in the BCH block (see erratum #2847). * If you try to soft reset the BCH block, it becomes unusable until * the next hard reset. This case occurs in the NAND boot mode. When the board * boots by NAND, the ROM of the chip will initialize the BCH blocks itself. * So If the driver tries to reset the BCH again, the BCH will not work anymore. - * You will see a DMA timeout in this case. + * You will see a DMA timeout in this case. The bug has been fixed + * in the following chips, such as MX28. * * To avoid this bug, just add a new parameter `just_enable` for * the mxs_reset_block(), and rewrite it here. */ -int gpmi_reset_block(void __iomem *reset_addr, bool just_enable) +static int gpmi_reset_block(void __iomem *reset_addr, bool just_enable) { int ret; int timeout = 0x400; @@ -206,7 +208,15 @@ int bch_set_geometry(struct gpmi_nand_data *this) if (ret) goto err_out; - ret = gpmi_reset_block(r->bch_regs, true); + /* + * Due to erratum #2847 of the MX23, the BCH cannot be soft reset on this + * chip, otherwise it will lock up. So we skip resetting BCH on the MX23. + * On the other hand, the MX28 needs the reset, because one case has been + * seen where the BCH produced ECC errors constantly after 10000 + * consecutive reboots. The latter case has not been seen on the MX23 yet, + * still we don't know if it could happen there as well. + */ + ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MX23(this)); if (ret) goto err_out; diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 35b4565050f1..8a393f9e6027 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -2588,7 +2588,7 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, instr->state = MTD_ERASING; while (len) { - /* Heck if we have a bad block, we do not erase bad blocks! */ + /* Check if we have a bad block, we do not erase bad blocks! */ if (nand_block_checkbad(mtd, ((loff_t) page) << chip->page_shift, 0, allowbbt)) { pr_warn("%s: attempt to erase a bad block at page 0x%08x\n", |