1 files changed, 225 insertions, 91 deletions

diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
index fb99ccff9080..cdb845b68ab5 100644
--- a/drivers/mmc/core/sdio.c
+++ b/drivers/mmc/core/sdio.c
@@ -165,6 +165,29 @@ static int sdio_enable_wide(struct mmc_card *card)
 }
 
 /*
+ * If desired, disconnect the pull-up resistor on CD/DAT[3] (pin 1)
+ * of the card. This may be required on certain setups of boards,
+ * controllers and embedded sdio device which do not need the card's
+ * pull-up. As a result, card detection is disabled and power is saved.
+ */
+static int sdio_disable_cd(struct mmc_card *card)
+{
+	int ret;
+	u8 ctrl;
+
+	if (!card->cccr.disable_cd)
+		return 0;
+
+	ret = mmc_io_rw_direct(card, 0, 0, SDIO_CCCR_IF, 0, &ctrl);
+	if (ret)
+		return ret;
+
+	ctrl |= SDIO_BUS_CD_DISABLE;
+
+	return mmc_io_rw_direct(card, 1, 0, SDIO_CCCR_IF, ctrl, NULL);
+}
+
+/*
  * Test if the card supports high-speed mode and, if so, switch to it.
  */
 static int sdio_enable_hs(struct mmc_card *card)
@@ -195,6 +218,135 @@ static int sdio_enable_hs(struct mmc_card *card)
 }
 
 /*
+ * Handle the detection and initialisation of a card.
+ *
+ * In the case of a resume, "oldcard" will contain the card
+ * we're trying to reinitialise.
+ */
+static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
+			      struct mmc_card *oldcard)
+{
+	struct mmc_card *card;
+	int err;
+
+	BUG_ON(!host);
+	WARN_ON(!host->claimed);
+
+	/*
+	 * Inform the card of the voltage
+	 */
+	err = mmc_send_io_op_cond(host, host->ocr, &ocr);
+	if (err)
+		goto err;
+
+	/*
+	 * For SPI, enable CRC as appropriate.
+	 */
+	if (mmc_host_is_spi(host)) {
+		err = mmc_spi_set_crc(host, use_spi_crc);
+		if (err)
+			goto err;
+	}
+
+	/*
+	 * Allocate card structure.
+	 */
+	card = mmc_alloc_card(host, NULL);
+	if (IS_ERR(card)) {
+		err = PTR_ERR(card);
+		goto err;
+	}
+
+	card->type = MMC_TYPE_SDIO;
+
+	/*
+	 * For native busses:  set card RCA and quit open drain mode.
+	 */
+	if (!mmc_host_is_spi(host)) {
+		err = mmc_send_relative_addr(host, &card->rca);
+		if (err)
+			goto remove;
+
+		mmc_set_bus_mode(host, MMC_BUSMODE_PUSHPULL);
+	}
+
+	/*
+	 * Select card, as all following commands rely on that.
+	 */
+	if (!mmc_host_is_spi(host)) {
+		err = mmc_select_card(card);
+		if (err)
+			goto remove;
+	}
+
+	/*
+	 * Read the common registers.
+	 */
+	err = sdio_read_cccr(card);
+	if (err)
+		goto remove;
+
+	/*
+	 * Read the common CIS tuples.
+	 */
+	err = sdio_read_common_cis(card);
+	if (err)
+		goto remove;
+
+	if (oldcard) {
+		int same = (card->cis.vendor == oldcard->cis.vendor &&
+			    card->cis.device == oldcard->cis.device);
+		mmc_remove_card(card);
+		if (!same) {
+			err = -ENOENT;
+			goto err;
+		}
+		card = oldcard;
+		return 0;
+	}
+
+	/*
+	 * Switch to high-speed (if supported).
+	 */
+	err = sdio_enable_hs(card);
+	if (err)
+		goto remove;
+
+	/*
+	 * Change to the card's maximum speed.
+	 */
+	if (mmc_card_highspeed(card)) {
+		/*
+		 * The SDIO specification doesn't mention how
+		 * the CIS transfer speed register relates to
+		 * high-speed, but it seems that 50 MHz is
+		 * mandatory.
+		 */
+		mmc_set_clock(host, 50000000);
+	} else {
+		mmc_set_clock(host, card->cis.max_dtr);
+	}
+
+	/*
+	 * Switch to wider bus (if supported).
+	 */
+	err = sdio_enable_wide(card);
+	if (err)
+		goto remove;
+
+	if (!oldcard)
+		host->card = card;
+	return 0;
+
+remove:
+	if (!oldcard)
+		mmc_remove_card(card);
+
+err:
+	return err;
+}
+
+/*
  * Host is being removed. Free up the current card.
  */
 static void mmc_sdio_remove(struct mmc_host *host)
@@ -243,10 +395,77 @@ static void mmc_sdio_detect(struct mmc_host *host)
 	}
 }
 
+/*
+ * SDIO suspend.  We need to suspend all functions separately.
+ * Therefore all registered functions must have drivers with suspend
+ * and resume methods.  Failing that we simply remove the whole card.
+ */
+static int mmc_sdio_suspend(struct mmc_host *host)
+{
+	int i, err = 0;
+
+	for (i = 0; i < host->card->sdio_funcs; i++) {
+		struct sdio_func *func = host->card->sdio_func[i];
+		if (func && sdio_func_present(func) && func->dev.driver) {
+			const struct dev_pm_ops *pmops = func->dev.driver->pm;
+			if (!pmops || !pmops->suspend || !pmops->resume) {
+				/* force removal of entire card in that case */
+				err = -ENOSYS;
+			} else
+				err = pmops->suspend(&func->dev);
+			if (err)
+				break;
+		}
+	}
+	while (err && --i >= 0) {
+		struct sdio_func *func = host->card->sdio_func[i];
+		if (func && sdio_func_present(func) && func->dev.driver) {
+			const struct dev_pm_ops *pmops = func->dev.driver->pm;
+			pmops->resume(&func->dev);
+		}
+	}
+
+	return err;
+}
+
+static int mmc_sdio_resume(struct mmc_host *host)
+{
+	int i, err;
+
+	BUG_ON(!host);
+	BUG_ON(!host->card);
+
+	/* Basic card reinitialization. */
+	mmc_claim_host(host);
+	err = mmc_sdio_init_card(host, host->ocr, host->card);
+	mmc_release_host(host);
+
+	/*
+	 * If the card looked to be the same as before suspending, then
+	 * we proceed to resume all card functions.  If one of them returns
+	 * an error then we simply return that error to the core and the
+	 * card will be redetected as new.  It is the responsibility of
+	 * the function driver to perform further tests with the extra
+	 * knowledge it has of the card to confirm the card is indeed the
+	 * same as before suspending (same MAC address for network cards,
+	 * etc.) and return an error otherwise.
+	 */
+	for (i = 0; !err && i < host->card->sdio_funcs; i++) {
+		struct sdio_func *func = host->card->sdio_func[i];
+		if (func && sdio_func_present(func) && func->dev.driver) {
+			const struct dev_pm_ops *pmops = func->dev.driver->pm;
+			err = pmops->resume(&func->dev);
+		}
+	}
+
+	return err;
+}
 
 static const struct mmc_bus_ops mmc_sdio_ops = {
 	.remove = mmc_sdio_remove,
 	.detect = mmc_sdio_detect,
+	.suspend = mmc_sdio_suspend,
+	.resume = mmc_sdio_resume,
 };
 
 
@@ -275,13 +494,6 @@ int mmc_attach_sdio(struct mmc_host *host, u32 ocr)
 		ocr &= ~0x7F;
 	}
 
-	if (ocr & MMC_VDD_165_195) {
-		printk(KERN_WARNING "%s: SDIO card claims to support the "
-		       "incompletely defined 'low voltage range'. This "
-		       "will be ignored.\n", mmc_hostname(host));
-		ocr &= ~MMC_VDD_165_195;
-	}
-
 	host->ocr = mmc_select_voltage(host, ocr);
 
 	/*
@@ -293,101 +505,23 @@ int mmc_attach_sdio(struct mmc_host *host, u32 ocr)
 	}
 
 	/*
-	 * Inform the card of the voltage
+	 * Detect and init the card.
 	 */
-	err = mmc_send_io_op_cond(host, host->ocr, &ocr);
+	err = mmc_sdio_init_card(host, host->ocr, NULL);
 	if (err)
 		goto err;
-
-	/*
-	 * For SPI, enable CRC as appropriate.
-	 */
-	if (mmc_host_is_spi(host)) {
-		err = mmc_spi_set_crc(host, use_spi_crc);
-		if (err)
-			goto err;
-	}
+	card = host->card;
 
 	/*
 	 * The number of functions on the card is encoded inside
 	 * the ocr.
 	 */
-	funcs = (ocr & 0x70000000) >> 28;
-
-	/*
-	 * Allocate card structure.
-	 */
-	card = mmc_alloc_card(host, NULL);
-	if (IS_ERR(card)) {
-		err = PTR_ERR(card);
-		goto err;
-	}
-
-	card->type = MMC_TYPE_SDIO;
-	card->sdio_funcs = funcs;
-
-	host->card = card;
-
-	/*
-	 * For native busses:  set card RCA and quit open drain mode.
-	 */
-	if (!mmc_host_is_spi(host)) {
-		err = mmc_send_relative_addr(host, &card->rca);
-		if (err)
-			goto remove;
-
-		mmc_set_bus_mode(host, MMC_BUSMODE_PUSHPULL);
-	}
-
-	/*
-	 * Select card, as all following commands rely on that.
-	 */
-	if (!mmc_host_is_spi(host)) {
-		err = mmc_select_card(card);
-		if (err)
-			goto remove;
-	}
+	card->sdio_funcs = funcs = (ocr & 0x70000000) >> 28;
 
 	/*
-	 * Read the common registers.
+	 * If needed, disconnect card detection pull-up resistor.
 	 */
-	err = sdio_read_cccr(card);
-	if (err)
-		goto remove;
-
-	/*
-	 * Read the common CIS tuples.
-	 */
-	err = sdio_read_common_cis(card);
-	if (err)
-		goto remove;
-
-	/*
-	 * Switch to high-speed (if supported).
-	 */
-	err = sdio_enable_hs(card);
-	if (err)
-		goto remove;
-
-	/*
-	 * Change to the card's maximum speed.
-	 */
-	if (mmc_card_highspeed(card)) {
-		/*
-		 * The SDIO specification doesn't mention how
-		 * the CIS transfer speed register relates to
-		 * high-speed, but it seems that 50 MHz is
-		 * mandatory.
-		 */
-		mmc_set_clock(host, 50000000);
-	} else {
-		mmc_set_clock(host, card->cis.max_dtr);
-	}
-
-	/*
-	 * Switch to wider bus (if supported).
-	 */
-	err = sdio_enable_wide(card);
+	err = sdio_disable_cd(card);
 	if (err)
 		goto remove;