diff options
Diffstat (limited to 'drivers/misc/genwqe')
| -rw-r--r-- | drivers/misc/genwqe/card_base.c | 32 | ||||
| -rw-r--r-- | drivers/misc/genwqe/card_ddcb.c | 20 | ||||
| -rw-r--r-- | drivers/misc/genwqe/card_debugfs.c | 2 | ||||
| -rw-r--r-- | drivers/misc/genwqe/card_dev.c | 24 | ||||
| -rw-r--r-- | drivers/misc/genwqe/card_sysfs.c | 8 | ||||
| -rw-r--r-- | drivers/misc/genwqe/card_utils.c | 30 |
6 files changed, 89 insertions, 27 deletions
diff --git a/drivers/misc/genwqe/card_base.c b/drivers/misc/genwqe/card_base.c index 97b8ecc42383..c9b886618071 100644 --- a/drivers/misc/genwqe/card_base.c +++ b/drivers/misc/genwqe/card_base.c @@ -165,6 +165,7 @@ static void genwqe_dev_free(struct genwqe_dev *cd) /** * genwqe_bus_reset() - Card recovery + * @cd: GenWQE device information * * pci_reset_function() will recover the device and ensure that the * registers are accessible again when it completes with success. If @@ -262,6 +263,7 @@ static void genwqe_tweak_hardware(struct genwqe_dev *cd) /** * genwqe_recovery_on_fatal_gfir_required() - Version depended actions + * @cd: GenWQE device information * * Bitstreams older than 2013-02-17 have a bug where fatal GFIRs must * be ignored. This is e.g. true for the bitstream we gave to the card @@ -280,6 +282,7 @@ int genwqe_flash_readback_fails(struct genwqe_dev *cd) /** * genwqe_T_psec() - Calculate PF/VF timeout register content + * @cd: GenWQE device information * * Note: From a design perspective it turned out to be a bad idea to * use codes here to specifiy the frequency/speed values. An old @@ -303,6 +306,7 @@ static int genwqe_T_psec(struct genwqe_dev *cd) /** * genwqe_setup_pf_jtimer() - Setup PF hardware timeouts for DDCB execution + * @cd: GenWQE device information * * Do this _after_ card_reset() is called. Otherwise the values will * vanish. The settings need to be done when the queues are inactive. @@ -329,6 +333,7 @@ static bool genwqe_setup_pf_jtimer(struct genwqe_dev *cd) /** * genwqe_setup_vf_jtimer() - Setup VF hardware timeouts for DDCB execution + * @cd: GenWQE device information */ static bool genwqe_setup_vf_jtimer(struct genwqe_dev *cd) { @@ -543,6 +548,7 @@ static int genwqe_start(struct genwqe_dev *cd) /** * genwqe_stop() - Stop card operation + * @cd: GenWQE device information * * Recovery notes: * As long as genwqe_thread runs we might access registers during @@ -569,6 +575,8 @@ static int genwqe_stop(struct genwqe_dev *cd) /** * genwqe_recover_card() - Try to recover the card if it is possible + * @cd: GenWQE device information + * @fatal_err: Indicate whether to attempt soft reset * * If fatal_err is set no register access is possible anymore. It is * likely that genwqe_start fails in that situation. Proper error @@ -618,6 +626,7 @@ static int genwqe_health_check_cond(struct genwqe_dev *cd, u64 *gfir) /** * genwqe_fir_checking() - Check the fault isolation registers of the card + * @cd: GenWQE device information * * If this code works ok, can be tried out with help of the genwqe_poke tool: * sudo ./tools/genwqe_poke 0x8 0xfefefefefef @@ -762,6 +771,7 @@ static u64 genwqe_fir_checking(struct genwqe_dev *cd) /** * genwqe_pci_fundamental_reset() - trigger a PCIe fundamental reset on the slot + * @pci_dev: PCI device information struct * * Note: pci_set_pcie_reset_state() is not implemented on all archs, so this * reset method will not work in all cases. @@ -826,8 +836,9 @@ static int genwqe_platform_recovery(struct genwqe_dev *cd) return rc; } -/* +/** * genwqe_reload_bistream() - reload card bitstream + * @cd: GenWQE device information * * Set the appropriate register and call fundamental reset to reaload the card * bitstream. @@ -880,6 +891,7 @@ static int genwqe_reload_bistream(struct genwqe_dev *cd) /** * genwqe_health_thread() - Health checking thread + * @data: GenWQE device information * * This thread is only started for the PF of the card. * @@ -1043,18 +1055,17 @@ static int genwqe_health_thread_running(struct genwqe_dev *cd) static int genwqe_health_check_stop(struct genwqe_dev *cd) { - int rc; - if (!genwqe_health_thread_running(cd)) return -EIO; - rc = kthread_stop(cd->health_thread); + kthread_stop(cd->health_thread); cd->health_thread = NULL; return 0; } /** * genwqe_pci_setup() - Allocate PCIe related resources for our card + * @cd: GenWQE device information */ static int genwqe_pci_setup(struct genwqe_dev *cd) { @@ -1140,6 +1151,7 @@ static int genwqe_pci_setup(struct genwqe_dev *cd) /** * genwqe_pci_remove() - Free PCIe related resources for our card + * @cd: GenWQE device information */ static void genwqe_pci_remove(struct genwqe_dev *cd) { @@ -1154,7 +1166,8 @@ static void genwqe_pci_remove(struct genwqe_dev *cd) /** * genwqe_probe() - Device initialization - * @pdev: PCI device information struct + * @pci_dev: PCI device information struct + * @id: PCI device ID * * Callable for multiple cards. This function is called on bind. * @@ -1214,6 +1227,7 @@ static int genwqe_probe(struct pci_dev *pci_dev, /** * genwqe_remove() - Called when device is removed (hot-plugable) + * @pci_dev: PCI device information struct * * Or when driver is unloaded respecitively when unbind is done. */ @@ -1233,8 +1247,10 @@ static void genwqe_remove(struct pci_dev *pci_dev) genwqe_dev_free(cd); } -/* +/** * genwqe_err_error_detected() - Error detection callback + * @pci_dev: PCI device information struct + * @state: PCI channel state * * This callback is called by the PCI subsystem whenever a PCI bus * error is detected. @@ -1324,7 +1340,7 @@ static int genwqe_sriov_configure(struct pci_dev *dev, int numvfs) return 0; } -static struct pci_error_handlers genwqe_err_handler = { +static const struct pci_error_handlers genwqe_err_handler = { .error_detected = genwqe_err_error_detected, .mmio_enabled = genwqe_err_result_none, .slot_reset = genwqe_err_slot_reset, @@ -1342,6 +1358,8 @@ static struct pci_driver genwqe_driver = { /** * genwqe_devnode() - Set default access mode for genwqe devices. + * @dev: Pointer to device (unused) + * @mode: Carrier to pass-back given mode (permissions) * * Default mode should be rw for everybody. Do not change default * device name. diff --git a/drivers/misc/genwqe/card_ddcb.c b/drivers/misc/genwqe/card_ddcb.c index 905106579935..0db4000dedf2 100644 --- a/drivers/misc/genwqe/card_ddcb.c +++ b/drivers/misc/genwqe/card_ddcb.c @@ -1,5 +1,5 @@ // SPDX-License-Identifier: GPL-2.0-only -/** +/* * IBM Accelerator Family 'GenWQE' * * (C) Copyright IBM Corp. 2013 @@ -244,10 +244,13 @@ static int ddcb_requ_finished(struct genwqe_dev *cd, struct ddcb_requ *req) (cd->card_state != GENWQE_CARD_USED); } +#define RET_DDCB_APPENDED 1 +#define RET_DDCB_TAPPED 2 /** * enqueue_ddcb() - Enqueue a DDCB * @cd: pointer to genwqe device descriptor * @queue: queue this operation should be done on + * @pddcb: pointer to ddcb structure * @ddcb_no: pointer to ddcb number being tapped * * Start execution of DDCB by tapping or append to queue via NEXT @@ -259,9 +262,6 @@ static int ddcb_requ_finished(struct genwqe_dev *cd, struct ddcb_requ *req) * Return: 1 if new DDCB is appended to previous * 2 if DDCB queue is tapped via register/simulation */ -#define RET_DDCB_APPENDED 1 -#define RET_DDCB_TAPPED 2 - static int enqueue_ddcb(struct genwqe_dev *cd, struct ddcb_queue *queue, struct ddcb *pddcb, int ddcb_no) { @@ -316,6 +316,8 @@ static int enqueue_ddcb(struct genwqe_dev *cd, struct ddcb_queue *queue, /** * copy_ddcb_results() - Copy output state from real DDCB to request + * @req: pointer to requsted DDCB parameters + * @ddcb_no: pointer to ddcb number being tapped * * Copy DDCB ASV to request struct. There is no endian * conversion made, since data structure in ASV is still @@ -356,6 +358,7 @@ static void copy_ddcb_results(struct ddcb_requ *req, int ddcb_no) /** * genwqe_check_ddcb_queue() - Checks DDCB queue for completed work equests. * @cd: pointer to genwqe device descriptor + * @queue: queue to be checked * * Return: Number of DDCBs which were finished */ @@ -553,6 +556,8 @@ int __genwqe_wait_ddcb(struct genwqe_dev *cd, struct ddcb_requ *req) /** * get_next_ddcb() - Get next available DDCB * @cd: pointer to genwqe device descriptor + * @queue: DDCB queue + * @num: internal DDCB number * * DDCB's content is completely cleared but presets for PRE and * SEQNUM. This function must only be called when ddcb_lock is held. @@ -900,7 +905,7 @@ int __genwqe_enqueue_ddcb(struct genwqe_dev *cd, struct ddcb_requ *req, /** * __genwqe_execute_raw_ddcb() - Setup and execute DDCB * @cd: pointer to genwqe device descriptor - * @req: user provided DDCB request + * @cmd: user provided DDCB command * @f_flags: file mode: blocking, non-blocking */ int __genwqe_execute_raw_ddcb(struct genwqe_dev *cd, @@ -965,6 +970,7 @@ int __genwqe_execute_raw_ddcb(struct genwqe_dev *cd, /** * genwqe_next_ddcb_ready() - Figure out if the next DDCB is already finished + * @cd: pointer to genwqe device descriptor * * We use this as condition for our wait-queue code. */ @@ -993,6 +999,7 @@ static int genwqe_next_ddcb_ready(struct genwqe_dev *cd) /** * genwqe_ddcbs_in_flight() - Check how many DDCBs are in flight + * @cd: pointer to genwqe device descriptor * * Keep track on the number of DDCBs which ware currently in the * queue. This is needed for statistics as well as conditon if we want @@ -1171,6 +1178,7 @@ static irqreturn_t genwqe_vf_isr(int irq, void *dev_id) /** * genwqe_card_thread() - Work thread for the DDCB queue + * @data: pointer to genwqe device descriptor * * The idea is to check if there are DDCBs in processing. If there are * some finished DDCBs, we process them and wakeup the @@ -1299,6 +1307,7 @@ int genwqe_setup_service_layer(struct genwqe_dev *cd) /** * queue_wake_up_all() - Handles fatal error case + * @cd: pointer to genwqe device descriptor * * The PCI device got unusable and we have to stop all pending * requests as fast as we can. The code after this must purge the @@ -1323,6 +1332,7 @@ static int queue_wake_up_all(struct genwqe_dev *cd) /** * genwqe_finish_queue() - Remove any genwqe devices and user-interfaces + * @cd: pointer to genwqe device descriptor * * Relies on the pre-condition that there are no users of the card * device anymore e.g. with open file-descriptors. diff --git a/drivers/misc/genwqe/card_debugfs.c b/drivers/misc/genwqe/card_debugfs.c index 1b5b82e65268..491fb4482da2 100644 --- a/drivers/misc/genwqe/card_debugfs.c +++ b/drivers/misc/genwqe/card_debugfs.c @@ -1,5 +1,5 @@ // SPDX-License-Identifier: GPL-2.0-only -/** +/* * IBM Accelerator Family 'GenWQE' * * (C) Copyright IBM Corp. 2013 diff --git a/drivers/misc/genwqe/card_dev.c b/drivers/misc/genwqe/card_dev.c index 040a0bda3125..55fc5b80e649 100644 --- a/drivers/misc/genwqe/card_dev.c +++ b/drivers/misc/genwqe/card_dev.c @@ -1,5 +1,5 @@ // SPDX-License-Identifier: GPL-2.0-only -/** +/* * IBM Accelerator Family 'GenWQE' * * (C) Copyright IBM Corp. 2013 @@ -87,7 +87,7 @@ static int genwqe_del_pin(struct genwqe_file *cfile, struct dma_mapping *m) * @cfile: Descriptor of opened file * @u_addr: User virtual address * @size: Size of buffer - * @dma_addr: DMA address to be updated + * @virt_addr: Virtual address to be updated * * Return: Pointer to the corresponding mapping NULL if not found */ @@ -144,6 +144,7 @@ static void __genwqe_del_mapping(struct genwqe_file *cfile, * @u_addr: user virtual address * @size: size of buffer * @dma_addr: DMA address to be updated + * @virt_addr: Virtual address to be updated * Return: Pointer to the corresponding mapping NULL if not found */ static struct dma_mapping *__genwqe_search_mapping(struct genwqe_file *cfile, @@ -249,6 +250,8 @@ static void genwqe_remove_pinnings(struct genwqe_file *cfile) /** * genwqe_kill_fasync() - Send signal to all processes with open GenWQE files + * @cd: GenWQE device information + * @sig: Signal to send out * * E.g. genwqe_send_signal(cd, SIGIO); */ @@ -380,6 +383,7 @@ static void genwqe_vma_open(struct vm_area_struct *vma) /** * genwqe_vma_close() - Called each time when vma is unmapped + * @vma: VMA area to close * * Free memory which got allocated by GenWQE mmap(). */ @@ -416,6 +420,8 @@ static const struct vm_operations_struct genwqe_vma_ops = { /** * genwqe_mmap() - Provide contignous buffers to userspace + * @filp: File pointer (unused) + * @vma: VMA area to map * * We use mmap() to allocate contignous buffers used for DMA * transfers. After the buffer is allocated we remap it to user-space @@ -484,16 +490,15 @@ static int genwqe_mmap(struct file *filp, struct vm_area_struct *vma) return rc; } +#define FLASH_BLOCK 0x40000 /* we use 256k blocks */ + /** * do_flash_update() - Excute flash update (write image or CVPD) - * @cd: genwqe device + * @cfile: Descriptor of opened file * @load: details about image load * * Return: 0 if successful */ - -#define FLASH_BLOCK 0x40000 /* we use 256k blocks */ - static int do_flash_update(struct genwqe_file *cfile, struct genwqe_bitstream *load) { @@ -820,6 +825,8 @@ static int genwqe_unpin_mem(struct genwqe_file *cfile, struct genwqe_mem *m) /** * ddcb_cmd_cleanup() - Remove dynamically created fixup entries + * @cfile: Descriptor of opened file + * @req: DDCB work request * * Only if there are any. Pinnings are not removed. */ @@ -844,6 +851,8 @@ static int ddcb_cmd_cleanup(struct genwqe_file *cfile, struct ddcb_requ *req) /** * ddcb_cmd_fixups() - Establish DMA fixups/sglists for user memory references + * @cfile: Descriptor of opened file + * @req: DDCB work request * * Before the DDCB gets executed we need to handle the fixups. We * replace the user-space addresses with DMA addresses or do @@ -974,6 +983,8 @@ static int ddcb_cmd_fixups(struct genwqe_file *cfile, struct ddcb_requ *req) /** * genwqe_execute_ddcb() - Execute DDCB using userspace address fixups + * @cfile: Descriptor of opened file + * @cmd: Command identifier (passed from user) * * The code will build up the translation tables or lookup the * contignous memory allocation table to find the right translations @@ -1339,6 +1350,7 @@ static int genwqe_inform_and_stop_processes(struct genwqe_dev *cd) /** * genwqe_device_remove() - Remove genwqe's char device + * @cd: GenWQE device information * * This function must be called after the client devices are removed * because it will free the major/minor number range for the genwqe diff --git a/drivers/misc/genwqe/card_sysfs.c b/drivers/misc/genwqe/card_sysfs.c index 28a3fb1533f7..b2f115602523 100644 --- a/drivers/misc/genwqe/card_sysfs.c +++ b/drivers/misc/genwqe/card_sysfs.c @@ -1,5 +1,5 @@ // SPDX-License-Identifier: GPL-2.0-only -/** +/* * IBM Accelerator Family 'GenWQE' * * (C) Copyright IBM Corp. 2013 @@ -129,7 +129,7 @@ static ssize_t base_clock_show(struct device *dev, } static DEVICE_ATTR_RO(base_clock); -/** +/* * curr_bitstream_show() - Show the current bitstream id * * There is a bug in some old versions of the CPLD which selects the @@ -156,7 +156,7 @@ static ssize_t curr_bitstream_show(struct device *dev, } static DEVICE_ATTR_RO(curr_bitstream); -/** +/* * next_bitstream_show() - Show the next activated bitstream * * IO_SLC_CFGREG_SOFTRESET: This register can only be accessed by the PF. @@ -260,7 +260,7 @@ static struct attribute *genwqe_normal_attributes[] = { NULL, }; -/** +/* * genwqe_is_visible() - Determine if sysfs attribute should be visible or not * * VFs have restricted mmio capabilities, so not all sysfs entries diff --git a/drivers/misc/genwqe/card_utils.c b/drivers/misc/genwqe/card_utils.c index 77c21caf2acd..039b923d1d60 100644 --- a/drivers/misc/genwqe/card_utils.c +++ b/drivers/misc/genwqe/card_utils.c @@ -1,5 +1,5 @@ // SPDX-License-Identifier: GPL-2.0-only -/** +/* * IBM Accelerator Family 'GenWQE' * * (C) Copyright IBM Corp. 2013 @@ -129,6 +129,9 @@ u32 __genwqe_readl(struct genwqe_dev *cd, u64 byte_offs) /** * genwqe_read_app_id() - Extract app_id + * @cd: genwqe device descriptor + * @app_name: carrier used to pass-back name + * @len: length of data for name * * app_unitcfg need to be filled with valid data first */ @@ -183,7 +186,7 @@ void genwqe_init_crc32(void) * @init: initial crc (0xffffffff at start) * * polynomial = x^32 * + x^29 + x^18 + x^14 + x^3 + 1 (0x20044009) - + * * Example: 4 bytes 0x01 0x02 0x03 0x04 with init=0xffffffff should * result in a crc32 of 0xf33cb7d3. * @@ -277,7 +280,7 @@ static int genwqe_sgl_size(int num_pages) return roundup(len, PAGE_SIZE); } -/** +/* * genwqe_alloc_sync_sgl() - Allocate memory for sgl and overlapping pages * * Allocates memory for sgl and overlapping pages. Pages which might @@ -460,6 +463,8 @@ int genwqe_setup_sgl(struct genwqe_dev *cd, struct genwqe_sgl *sgl, /** * genwqe_free_sync_sgl() - Free memory for sgl and overlapping pages + * @cd: genwqe device descriptor + * @sgl: scatter gather list describing user-space memory * * After the DMA transfer has been completed we free the memory for * the sgl and the cached pages. Data is being transferred from cached @@ -710,6 +715,7 @@ int genwqe_read_softreset(struct genwqe_dev *cd) /** * genwqe_set_interrupt_capability() - Configure MSI capability structure * @cd: pointer to the device + * @count: number of vectors to allocate * Return: 0 if no error */ int genwqe_set_interrupt_capability(struct genwqe_dev *cd, int count) @@ -738,7 +744,7 @@ void genwqe_reset_interrupt_capability(struct genwqe_dev *cd) * @i: index to desired entry * @m: maximum possible entries * @addr: addr which is read - * @index: index in debug array + * @idx: index in debug array * @val: read value */ static int set_reg_idx(struct genwqe_dev *cd, struct genwqe_reg *r, @@ -818,6 +824,8 @@ int genwqe_read_ffdc_regs(struct genwqe_dev *cd, struct genwqe_reg *regs, /** * genwqe_ffdc_buff_size() - Calculates the number of dump registers + * @cd: genwqe device descriptor + * @uid: unit ID */ int genwqe_ffdc_buff_size(struct genwqe_dev *cd, int uid) { @@ -871,6 +879,10 @@ int genwqe_ffdc_buff_size(struct genwqe_dev *cd, int uid) /** * genwqe_ffdc_buff_read() - Implements LogoutExtendedErrorRegisters procedure + * @cd: genwqe device descriptor + * @uid: unit ID + * @regs: register information + * @max_regs: number of register entries */ int genwqe_ffdc_buff_read(struct genwqe_dev *cd, int uid, struct genwqe_reg *regs, unsigned int max_regs) @@ -956,6 +968,10 @@ int genwqe_ffdc_buff_read(struct genwqe_dev *cd, int uid, /** * genwqe_write_vreg() - Write register in virtual window + * @cd: genwqe device descriptor + * @reg: register (byte) offset within BAR + * @val: value to write + * @func: PCI virtual function * * Note, these registers are only accessible to the PF through the * VF-window. It is not intended for the VF to access. @@ -969,6 +985,9 @@ int genwqe_write_vreg(struct genwqe_dev *cd, u32 reg, u64 val, int func) /** * genwqe_read_vreg() - Read register in virtual window + * @cd: genwqe device descriptor + * @reg: register (byte) offset within BAR + * @func: PCI virtual function * * Note, these registers are only accessible to the PF through the * VF-window. It is not intended for the VF to access. @@ -981,6 +1000,7 @@ u64 genwqe_read_vreg(struct genwqe_dev *cd, u32 reg, int func) /** * genwqe_base_clock_frequency() - Deteremine base clock frequency of the card + * @cd: genwqe device descriptor * * Note: From a design perspective it turned out to be a bad idea to * use codes here to specifiy the frequency/speed values. An old @@ -1005,6 +1025,7 @@ int genwqe_base_clock_frequency(struct genwqe_dev *cd) /** * genwqe_stop_traps() - Stop traps + * @cd: genwqe device descriptor * * Before reading out the analysis data, we need to stop the traps. */ @@ -1015,6 +1036,7 @@ void genwqe_stop_traps(struct genwqe_dev *cd) /** * genwqe_start_traps() - Start traps + * @cd: genwqe device descriptor * * After having read the data, we can/must enable the traps again. */ |