1 files changed, 224 insertions, 95 deletions

diff --git a/drivers/media/video/cx18/cx18-gpio.c b/drivers/media/video/cx18/cx18-gpio.c
index 1a99329f33cb..5518d1424f8f 100644
--- a/drivers/media/video/cx18/cx18-gpio.c
+++ b/drivers/media/video/cx18/cx18-gpio.c
@@ -46,6 +46,9 @@
  * gpio13: cs5345 reset pin
 */
 
+/*
+ * File scope utility functions
+ */
 static void gpio_write(struct cx18 *cx)
 {
 	u32 dir_lo = cx->gpio_dir & 0xffff;
@@ -63,73 +66,201 @@ static void gpio_write(struct cx18 *cx)
 					CX18_REG_GPIO_OUT2, val_hi, dir_hi);
 }
 
-void cx18_reset_i2c_slaves_gpio(struct cx18 *cx)
+static void gpio_update(struct cx18 *cx, u32 mask, u32 data)
 {
-	const struct cx18_gpio_i2c_slave_reset *p;
+	if (mask == 0)
+		return;
 
-	p = &cx->card->gpio_i2c_slave_reset;
+	mutex_lock(&cx->gpio_lock);
+	cx->gpio_val = (cx->gpio_val & ~mask) | (data & mask);
+	gpio_write(cx);
+	mutex_unlock(&cx->gpio_lock);
+}
+
+static void gpio_reset_seq(struct cx18 *cx, u32 active_lo, u32 active_hi,
+			   unsigned int assert_msecs,
+			   unsigned int recovery_msecs)
+{
+	u32 mask;
 
-	if ((p->active_lo_mask | p->active_hi_mask) == 0)
+	mask = active_lo | active_hi;
+	if (mask == 0)
 		return;
 
-	/* Assuming that the masks are a subset of the bits in gpio_dir */
+	/*
+	 * Assuming that active_hi and active_lo are a subsets of the bits in
+	 * gpio_dir.  Also assumes that active_lo and active_hi don't overlap
+	 * in any bit position
+	 */
 
 	/* Assert */
-	mutex_lock(&cx->gpio_lock);
-	cx->gpio_val =
-		(cx->gpio_val | p->active_hi_mask) & ~(p->active_lo_mask);
-	gpio_write(cx);
-	schedule_timeout_uninterruptible(msecs_to_jiffies(p->msecs_asserted));
+	gpio_update(cx, mask, ~active_lo);
+	schedule_timeout_uninterruptible(msecs_to_jiffies(assert_msecs));
 
 	/* Deassert */
-	cx->gpio_val =
-		(cx->gpio_val | p->active_lo_mask) & ~(p->active_hi_mask);
-	gpio_write(cx);
-	schedule_timeout_uninterruptible(msecs_to_jiffies(p->msecs_recovery));
+	gpio_update(cx, mask, ~active_hi);
+	schedule_timeout_uninterruptible(msecs_to_jiffies(recovery_msecs));
+}
+
+/*
+ * GPIO Multiplexer - logical device
+ */
+static int gpiomux_log_status(struct v4l2_subdev *sd)
+{
+	struct cx18 *cx = v4l2_get_subdevdata(sd);
+
+	mutex_lock(&cx->gpio_lock);
+	CX18_INFO_DEV(sd, "GPIO:  direction 0x%08x, value 0x%08x\n",
+		      cx->gpio_dir, cx->gpio_val);
 	mutex_unlock(&cx->gpio_lock);
+	return 0;
 }
 
-void cx18_reset_ir_gpio(void *data)
+static int gpiomux_s_radio(struct v4l2_subdev *sd)
 {
-	struct cx18 *cx = ((struct cx18_i2c_algo_callback_data *)data)->cx;
-	const struct cx18_gpio_i2c_slave_reset *p;
+	struct cx18 *cx = v4l2_get_subdevdata(sd);
 
-	p = &cx->card->gpio_i2c_slave_reset;
+	/*
+	 * FIXME - work out the cx->active/audio_input mess - this is
+	 * intended to handle the switch to radio mode and set the
+	 * audio routing, but we need to update the state in cx
+	 */
+	gpio_update(cx, cx->card->gpio_audio_input.mask,
+			cx->card->gpio_audio_input.radio);
+	return 0;
+}
 
-	if (p->ir_reset_mask == 0)
-		return;
+static int gpiomux_s_std(struct v4l2_subdev *sd, v4l2_std_id norm)
+{
+	struct cx18 *cx = v4l2_get_subdevdata(sd);
+	u32 data;
 
-	CX18_DEBUG_INFO("Resetting IR microcontroller\n");
+	switch (cx->card->audio_inputs[cx->audio_input].muxer_input) {
+	case 1:
+		data = cx->card->gpio_audio_input.linein;
+		break;
+	case 0:
+		data = cx->card->gpio_audio_input.tuner;
+		break;
+	default:
+		/*
+		 * FIXME - work out the cx->active/audio_input mess - this is
+		 * intended to handle the switch from radio mode and set the
+		 * audio routing, but we need to update the state in cx
+		 */
+		data = cx->card->gpio_audio_input.tuner;
+		break;
+	}
+	gpio_update(cx, cx->card->gpio_audio_input.mask, data);
+	return 0;
+}
 
-	/*
-	   Assert timing for the Z8F0811 on HVR-1600 boards:
-	   1. Assert RESET for min of 4 clock cycles at 18.432 MHz to initiate
-	   2. Reset then takes 66 WDT cycles at 10 kHz + 16 xtal clock cycles
-		(6,601,085 nanoseconds ~= 7 milliseconds)
-	   3. DBG pin must be high before chip exits reset for normal operation.
-		DBG is open drain and hopefully pulled high since we don't
-		normally drive it (GPIO 1?) for the HVR-1600
-	   4. Z8F0811 won't exit reset until RESET is deasserted
-	*/
-	mutex_lock(&cx->gpio_lock);
-	cx->gpio_val = cx->gpio_val & ~p->ir_reset_mask;
-	gpio_write(cx);
-	mutex_unlock(&cx->gpio_lock);
-	schedule_timeout_uninterruptible(msecs_to_jiffies(p->msecs_asserted));
+static int gpiomux_s_audio_routing(struct v4l2_subdev *sd,
+				   const struct v4l2_routing *route)
+{
+	struct cx18 *cx = v4l2_get_subdevdata(sd);
+	u32 data;
+
+	switch (route->input) {
+	case 0:
+		data = cx->card->gpio_audio_input.tuner;
+		break;
+	case 1:
+		data = cx->card->gpio_audio_input.linein;
+		break;
+	case 2:
+		data = cx->card->gpio_audio_input.radio;
+		break;
+	default:
+		return -EINVAL;
+	}
+	gpio_update(cx, cx->card->gpio_audio_input.mask, data);
+	return 0;
+}
+
+static const struct v4l2_subdev_core_ops gpiomux_core_ops = {
+	.log_status = gpiomux_log_status,
+};
+
+static const struct v4l2_subdev_tuner_ops gpiomux_tuner_ops = {
+	.s_std = gpiomux_s_std,
+	.s_radio = gpiomux_s_radio,
+};
+
+static const struct v4l2_subdev_audio_ops gpiomux_audio_ops = {
+	.s_routing = gpiomux_s_audio_routing,
+};
+
+static const struct v4l2_subdev_ops gpiomux_ops = {
+	.core = &gpiomux_core_ops,
+	.tuner = &gpiomux_tuner_ops,
+	.audio = &gpiomux_audio_ops,
+};
+
+/*
+ * GPIO Reset Controller - logical device
+ */
+static int resetctrl_log_status(struct v4l2_subdev *sd)
+{
+	struct cx18 *cx = v4l2_get_subdevdata(sd);
 
-	/*
-	   Zilog comes out of reset, loads reset vector address and executes
-	   from there. Required recovery delay unknown.
-	*/
 	mutex_lock(&cx->gpio_lock);
-	cx->gpio_val = cx->gpio_val | p->ir_reset_mask;
-	gpio_write(cx);
+	CX18_INFO_DEV(sd, "GPIO:  direction 0x%08x, value 0x%08x\n",
+		      cx->gpio_dir, cx->gpio_val);
 	mutex_unlock(&cx->gpio_lock);
-	schedule_timeout_uninterruptible(msecs_to_jiffies(p->msecs_recovery));
+	return 0;
 }
-EXPORT_SYMBOL(cx18_reset_ir_gpio);
-/* This symbol is exported for use by an infrared module for the IR-blaster */
 
+static int resetctrl_reset(struct v4l2_subdev *sd, u32 val)
+{
+	struct cx18 *cx = v4l2_get_subdevdata(sd);
+	const struct cx18_gpio_i2c_slave_reset *p;
+
+	p = &cx->card->gpio_i2c_slave_reset;
+	switch (val) {
+	case CX18_GPIO_RESET_I2C:
+		gpio_reset_seq(cx, p->active_lo_mask, p->active_hi_mask,
+			       p->msecs_asserted, p->msecs_recovery);
+		break;
+	case CX18_GPIO_RESET_Z8F0811:
+		/*
+		 * Assert timing for the Z8F0811 on HVR-1600 boards:
+		 * 1. Assert RESET for min of 4 clock cycles at 18.432 MHz to
+		 *    initiate
+		 * 2. Reset then takes 66 WDT cycles at 10 kHz + 16 xtal clock
+		 *    cycles (6,601,085 nanoseconds ~= 7 milliseconds)
+		 * 3. DBG pin must be high before chip exits reset for normal
+		 *    operation.  DBG is open drain and hopefully pulled high
+		 *    since we don't normally drive it (GPIO 1?) for the
+		 *    HVR-1600
+		 * 4. Z8F0811 won't exit reset until RESET is deasserted
+		 * 5. Zilog comes out of reset, loads reset vector address and
+		 *    executes from there. Required recovery delay unknown.
+		 */
+		gpio_reset_seq(cx, p->ir_reset_mask, 0,
+			       p->msecs_asserted, p->msecs_recovery);
+		break;
+	case CX18_GPIO_RESET_XC2028:
+		if (cx->card->tuners[0].tuner == TUNER_XC2028)
+			gpio_reset_seq(cx, (1 << cx->card->xceive_pin), 0,
+				       1, 1);
+		break;
+	}
+	return 0;
+}
+
+static const struct v4l2_subdev_core_ops resetctrl_core_ops = {
+	.log_status = resetctrl_log_status,
+	.reset = resetctrl_reset,
+};
+
+static const struct v4l2_subdev_ops resetctrl_ops = {
+	.core = &resetctrl_core_ops,
+};
+
+/*
+ * External entry points
+ */
 void cx18_gpio_init(struct cx18 *cx)
 {
 	mutex_lock(&cx->gpio_lock);
@@ -156,6 +287,49 @@ void cx18_gpio_init(struct cx18 *cx)
 	mutex_unlock(&cx->gpio_lock);
 }
 
+int cx18_gpio_register(struct cx18 *cx, u32 hw)
+{
+	struct v4l2_subdev *sd;
+	const struct v4l2_subdev_ops *ops;
+	char *str;
+
+	switch (hw) {
+	case CX18_HW_GPIO_MUX:
+		sd = &cx->sd_gpiomux;
+		ops = &gpiomux_ops;
+		str = "gpio-mux";
+		break;
+	case CX18_HW_GPIO_RESET_CTRL:
+		sd = &cx->sd_resetctrl;
+		ops = &resetctrl_ops;
+		str = "gpio-reset-ctrl";
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	v4l2_subdev_init(sd, ops);
+	v4l2_set_subdevdata(sd, cx);
+	snprintf(sd->name, sizeof(sd->name), "%s %s", cx->v4l2_dev.name, str);
+	sd->grp_id = hw;
+	return v4l2_device_register_subdev(&cx->v4l2_dev, sd);
+}
+
+void cx18_reset_ir_gpio(void *data)
+{
+	struct cx18 *cx = to_cx18((struct v4l2_device *)data);
+
+	if (cx->card->gpio_i2c_slave_reset.ir_reset_mask == 0)
+		return;
+
+	CX18_DEBUG_INFO("Resetting IR microcontroller\n");
+
+	v4l2_subdev_call(&cx->sd_resetctrl,
+			 core, reset, CX18_GPIO_RESET_Z8F0811);
+}
+EXPORT_SYMBOL(cx18_reset_ir_gpio);
+/* This symbol is exported for use by lirc_pvr150 for the IR-blaster */
+
 /* Xceive tuner reset function */
 int cx18_reset_tuner_gpio(void *dev, int component, int cmd, int value)
 {
@@ -163,56 +337,11 @@ int cx18_reset_tuner_gpio(void *dev, int component, int cmd, int value)
 	struct cx18_i2c_algo_callback_data *cb_data = algo->data;
 	struct cx18 *cx = cb_data->cx;
 
-	if (cmd != XC2028_TUNER_RESET)
+	if (cmd != XC2028_TUNER_RESET ||
+	    cx->card->tuners[0].tuner != TUNER_XC2028)
 		return 0;
-	CX18_DEBUG_INFO("Resetting tuner\n");
 
-	mutex_lock(&cx->gpio_lock);
-	cx->gpio_val &= ~(1 << cx->card->xceive_pin);
-	gpio_write(cx);
-	mutex_unlock(&cx->gpio_lock);
-	schedule_timeout_interruptible(msecs_to_jiffies(1));
-
-	mutex_lock(&cx->gpio_lock);
-	cx->gpio_val |= 1 << cx->card->xceive_pin;
-	gpio_write(cx);
-	mutex_unlock(&cx->gpio_lock);
-	schedule_timeout_interruptible(msecs_to_jiffies(1));
-	return 0;
-}
-
-int cx18_gpio(struct cx18 *cx, unsigned int command, void *arg)
-{
-	struct v4l2_routing *route = arg;
-	u32 mask, data;
-
-	switch (command) {
-	case VIDIOC_INT_S_AUDIO_ROUTING:
-		if (route->input > 2)
-			return -EINVAL;
-		mask = cx->card->gpio_audio_input.mask;
-		switch (route->input) {
-		case 0:
-			data = cx->card->gpio_audio_input.tuner;
-			break;
-		case 1:
-			data = cx->card->gpio_audio_input.linein;
-			break;
-		case 2:
-		default:
-			data = cx->card->gpio_audio_input.radio;
-			break;
-		}
-		break;
-
-	default:
-		return -EINVAL;
-	}
-	if (mask) {
-		mutex_lock(&cx->gpio_lock);
-		cx->gpio_val = (cx->gpio_val & ~mask) | (data & mask);
-		gpio_write(cx);
-		mutex_unlock(&cx->gpio_lock);
-	}
-	return 0;
+	CX18_DEBUG_INFO("Resetting XCeive tuner\n");
+	return v4l2_subdev_call(&cx->sd_resetctrl,
+				core, reset, CX18_GPIO_RESET_XC2028);
 }