1 files changed, 9 insertions, 189 deletions

diff --git a/drivers/infiniband/hw/qib/qib_eeprom.c b/drivers/infiniband/hw/qib/qib_eeprom.c
index 4d5d71aaa2b4..311ee6c3dd5e 100644
--- a/drivers/infiniband/hw/qib/qib_eeprom.c
+++ b/drivers/infiniband/hw/qib/qib_eeprom.c
@@ -153,6 +153,7 @@ void qib_get_eeprom_info(struct qib_devdata *dd)
 
 	if (t && dd0->nguid > 1 && t <= dd0->nguid) {
 		u8 oguid;
+
 		dd->base_guid = dd0->base_guid;
 		bguid = (u8 *) &dd->base_guid;
 
@@ -251,206 +252,25 @@ void qib_get_eeprom_info(struct qib_devdata *dd)
 		 * This board has a Serial-prefix, which is stored
 		 * elsewhere for backward-compatibility.
 		 */
-		memcpy(snp, ifp->if_sprefix, sizeof ifp->if_sprefix);
-		snp[sizeof ifp->if_sprefix] = '\0';
+		memcpy(snp, ifp->if_sprefix, sizeof(ifp->if_sprefix));
+		snp[sizeof(ifp->if_sprefix)] = '\0';
 		len = strlen(snp);
 		snp += len;
-		len = (sizeof dd->serial) - len;
-		if (len > sizeof ifp->if_serial)
-			len = sizeof ifp->if_serial;
+		len = sizeof(dd->serial) - len;
+		if (len > sizeof(ifp->if_serial))
+			len = sizeof(ifp->if_serial);
 		memcpy(snp, ifp->if_serial, len);
-	} else
-		memcpy(dd->serial, ifp->if_serial,
-		       sizeof ifp->if_serial);
+	} else {
+		memcpy(dd->serial, ifp->if_serial, sizeof(ifp->if_serial));
+	}
 	if (!strstr(ifp->if_comment, "Tested successfully"))
 		qib_dev_err(dd,
 			"Board SN %s did not pass functional test: %s\n",
 			dd->serial, ifp->if_comment);
 
-	memcpy(&dd->eep_st_errs, &ifp->if_errcntp, QIB_EEP_LOG_CNT);
-	/*
-	 * Power-on (actually "active") hours are kept as little-endian value
-	 * in EEPROM, but as seconds in a (possibly as small as 24-bit)
-	 * atomic_t while running.
-	 */
-	atomic_set(&dd->active_time, 0);
-	dd->eep_hrs = ifp->if_powerhour[0] | (ifp->if_powerhour[1] << 8);
-
 done:
 	vfree(buf);
 
 bail:;
 }
 
-/**
- * qib_update_eeprom_log - copy active-time and error counters to eeprom
- * @dd: the qlogic_ib device
- *
- * Although the time is kept as seconds in the qib_devdata struct, it is
- * rounded to hours for re-write, as we have only 16 bits in EEPROM.
- * First-cut code reads whole (expected) struct qib_flash, modifies,
- * re-writes. Future direction: read/write only what we need, assuming
- * that the EEPROM had to have been "good enough" for driver init, and
- * if not, we aren't making it worse.
- *
- */
-int qib_update_eeprom_log(struct qib_devdata *dd)
-{
-	void *buf;
-	struct qib_flash *ifp;
-	int len, hi_water;
-	uint32_t new_time, new_hrs;
-	u8 csum;
-	int ret, idx;
-	unsigned long flags;
-
-	/* first, check if we actually need to do anything. */
-	ret = 0;
-	for (idx = 0; idx < QIB_EEP_LOG_CNT; ++idx) {
-		if (dd->eep_st_new_errs[idx]) {
-			ret = 1;
-			break;
-		}
-	}
-	new_time = atomic_read(&dd->active_time);
-
-	if (ret == 0 && new_time < 3600)
-		goto bail;
-
-	/*
-	 * The quick-check above determined that there is something worthy
-	 * of logging, so get current contents and do a more detailed idea.
-	 * read full flash, not just currently used part, since it may have
-	 * been written with a newer definition
-	 */
-	len = sizeof(struct qib_flash);
-	buf = vmalloc(len);
-	ret = 1;
-	if (!buf) {
-		qib_dev_err(dd,
-			"Couldn't allocate memory to read %u bytes from eeprom for logging\n",
-			len);
-		goto bail;
-	}
-
-	/* Grab semaphore and read current EEPROM. If we get an
-	 * error, let go, but if not, keep it until we finish write.
-	 */
-	ret = mutex_lock_interruptible(&dd->eep_lock);
-	if (ret) {
-		qib_dev_err(dd, "Unable to acquire EEPROM for logging\n");
-		goto free_bail;
-	}
-	ret = qib_twsi_blk_rd(dd, dd->twsi_eeprom_dev, 0, buf, len);
-	if (ret) {
-		mutex_unlock(&dd->eep_lock);
-		qib_dev_err(dd, "Unable read EEPROM for logging\n");
-		goto free_bail;
-	}
-	ifp = (struct qib_flash *)buf;
-
-	csum = flash_csum(ifp, 0);
-	if (csum != ifp->if_csum) {
-		mutex_unlock(&dd->eep_lock);
-		qib_dev_err(dd, "EEPROM cks err (0x%02X, S/B 0x%02X)\n",
-			    csum, ifp->if_csum);
-		ret = 1;
-		goto free_bail;
-	}
-	hi_water = 0;
-	spin_lock_irqsave(&dd->eep_st_lock, flags);
-	for (idx = 0; idx < QIB_EEP_LOG_CNT; ++idx) {
-		int new_val = dd->eep_st_new_errs[idx];
-		if (new_val) {
-			/*
-			 * If we have seen any errors, add to EEPROM values
-			 * We need to saturate at 0xFF (255) and we also
-			 * would need to adjust the checksum if we were
-			 * trying to minimize EEPROM traffic
-			 * Note that we add to actual current count in EEPROM,
-			 * in case it was altered while we were running.
-			 */
-			new_val += ifp->if_errcntp[idx];
-			if (new_val > 0xFF)
-				new_val = 0xFF;
-			if (ifp->if_errcntp[idx] != new_val) {
-				ifp->if_errcntp[idx] = new_val;
-				hi_water = offsetof(struct qib_flash,
-						    if_errcntp) + idx;
-			}
-			/*
-			 * update our shadow (used to minimize EEPROM
-			 * traffic), to match what we are about to write.
-			 */
-			dd->eep_st_errs[idx] = new_val;
-			dd->eep_st_new_errs[idx] = 0;
-		}
-	}
-	/*
-	 * Now update active-time. We would like to round to the nearest hour
-	 * but unless atomic_t are sure to be proper signed ints we cannot,
-	 * because we need to account for what we "transfer" to EEPROM and
-	 * if we log an hour at 31 minutes, then we would need to set
-	 * active_time to -29 to accurately count the _next_ hour.
-	 */
-	if (new_time >= 3600) {
-		new_hrs = new_time / 3600;
-		atomic_sub((new_hrs * 3600), &dd->active_time);
-		new_hrs += dd->eep_hrs;
-		if (new_hrs > 0xFFFF)
-			new_hrs = 0xFFFF;
-		dd->eep_hrs = new_hrs;
-		if ((new_hrs & 0xFF) != ifp->if_powerhour[0]) {
-			ifp->if_powerhour[0] = new_hrs & 0xFF;
-			hi_water = offsetof(struct qib_flash, if_powerhour);
-		}
-		if ((new_hrs >> 8) != ifp->if_powerhour[1]) {
-			ifp->if_powerhour[1] = new_hrs >> 8;
-			hi_water = offsetof(struct qib_flash, if_powerhour) + 1;
-		}
-	}
-	/*
-	 * There is a tiny possibility that we could somehow fail to write
-	 * the EEPROM after updating our shadows, but problems from holding
-	 * the spinlock too long are a much bigger issue.
-	 */
-	spin_unlock_irqrestore(&dd->eep_st_lock, flags);
-	if (hi_water) {
-		/* we made some change to the data, uopdate cksum and write */
-		csum = flash_csum(ifp, 1);
-		ret = eeprom_write_with_enable(dd, 0, buf, hi_water + 1);
-	}
-	mutex_unlock(&dd->eep_lock);
-	if (ret)
-		qib_dev_err(dd, "Failed updating EEPROM\n");
-
-free_bail:
-	vfree(buf);
-bail:
-	return ret;
-}
-
-/**
- * qib_inc_eeprom_err - increment one of the four error counters
- * that are logged to EEPROM.
- * @dd: the qlogic_ib device
- * @eidx: 0..3, the counter to increment
- * @incr: how much to add
- *
- * Each counter is 8-bits, and saturates at 255 (0xFF). They
- * are copied to the EEPROM (aka flash) whenever qib_update_eeprom_log()
- * is called, but it can only be called in a context that allows sleep.
- * This function can be called even at interrupt level.
- */
-void qib_inc_eeprom_err(struct qib_devdata *dd, u32 eidx, u32 incr)
-{
-	uint new_val;
-	unsigned long flags;
-
-	spin_lock_irqsave(&dd->eep_st_lock, flags);
-	new_val = dd->eep_st_new_errs[eidx] + incr;
-	if (new_val > 255)
-		new_val = 255;
-	dd->eep_st_new_errs[eidx] = new_val;
-	spin_unlock_irqrestore(&dd->eep_st_lock, flags);
-}