diff options
Diffstat (limited to 'drivers/i2c')
-rw-r--r-- | drivers/i2c/busses/i2c-aspeed.c | 2 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-cpm.c | 3 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-i801.c | 27 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-meson.c | 52 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-mt65xx.c | 6 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-mxs.c | 10 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-npcm7xx.c | 9 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-owl.c | 6 | ||||
-rw-r--r-- | drivers/i2c/i2c-core-base.c | 2 |
9 files changed, 81 insertions, 36 deletions
diff --git a/drivers/i2c/busses/i2c-aspeed.c b/drivers/i2c/busses/i2c-aspeed.c index 31268074c422..724bf30600d6 100644 --- a/drivers/i2c/busses/i2c-aspeed.c +++ b/drivers/i2c/busses/i2c-aspeed.c @@ -69,6 +69,7 @@ * These share bit definitions, so use the same values for the enable & * status bits. */ +#define ASPEED_I2CD_INTR_RECV_MASK 0xf000ffff #define ASPEED_I2CD_INTR_SDA_DL_TIMEOUT BIT(14) #define ASPEED_I2CD_INTR_BUS_RECOVER_DONE BIT(13) #define ASPEED_I2CD_INTR_SLAVE_MATCH BIT(7) @@ -604,6 +605,7 @@ static irqreturn_t aspeed_i2c_bus_irq(int irq, void *dev_id) writel(irq_received & ~ASPEED_I2CD_INTR_RX_DONE, bus->base + ASPEED_I2C_INTR_STS_REG); readl(bus->base + ASPEED_I2C_INTR_STS_REG); + irq_received &= ASPEED_I2CD_INTR_RECV_MASK; irq_remaining = irq_received; #if IS_ENABLED(CONFIG_I2C_SLAVE) diff --git a/drivers/i2c/busses/i2c-cpm.c b/drivers/i2c/busses/i2c-cpm.c index 1213e1932ccb..24d584a1c9a7 100644 --- a/drivers/i2c/busses/i2c-cpm.c +++ b/drivers/i2c/busses/i2c-cpm.c @@ -65,6 +65,9 @@ struct i2c_ram { char res1[4]; /* Reserved */ ushort rpbase; /* Relocation pointer */ char res2[2]; /* Reserved */ + /* The following elements are only for CPM2 */ + char res3[4]; /* Reserved */ + uint sdmatmp; /* Internal */ }; #define I2COM_START 0x80 diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c index e32ef3f01fe8..bffca729e1c7 100644 --- a/drivers/i2c/busses/i2c-i801.c +++ b/drivers/i2c/busses/i2c-i801.c @@ -1709,6 +1709,16 @@ static inline int i801_acpi_probe(struct i801_priv *priv) { return 0; } static inline void i801_acpi_remove(struct i801_priv *priv) { } #endif +static unsigned char i801_setup_hstcfg(struct i801_priv *priv) +{ + unsigned char hstcfg = priv->original_hstcfg; + + hstcfg &= ~SMBHSTCFG_I2C_EN; /* SMBus timing */ + hstcfg |= SMBHSTCFG_HST_EN; + pci_write_config_byte(priv->pci_dev, SMBHSTCFG, hstcfg); + return hstcfg; +} + static int i801_probe(struct pci_dev *dev, const struct pci_device_id *id) { unsigned char temp; @@ -1830,14 +1840,10 @@ static int i801_probe(struct pci_dev *dev, const struct pci_device_id *id) return err; } - pci_read_config_byte(priv->pci_dev, SMBHSTCFG, &temp); - priv->original_hstcfg = temp; - temp &= ~SMBHSTCFG_I2C_EN; /* SMBus timing */ - if (!(temp & SMBHSTCFG_HST_EN)) { + pci_read_config_byte(priv->pci_dev, SMBHSTCFG, &priv->original_hstcfg); + temp = i801_setup_hstcfg(priv); + if (!(priv->original_hstcfg & SMBHSTCFG_HST_EN)) dev_info(&dev->dev, "Enabling SMBus device\n"); - temp |= SMBHSTCFG_HST_EN; - } - pci_write_config_byte(priv->pci_dev, SMBHSTCFG, temp); if (temp & SMBHSTCFG_SMB_SMI_EN) { dev_dbg(&dev->dev, "SMBus using interrupt SMI#\n"); @@ -1911,6 +1917,7 @@ static int i801_probe(struct pci_dev *dev, const struct pci_device_id *id) pci_set_drvdata(dev, priv); + dev_pm_set_driver_flags(&dev->dev, DPM_FLAG_NO_DIRECT_COMPLETE); pm_runtime_set_autosuspend_delay(&dev->dev, 1000); pm_runtime_use_autosuspend(&dev->dev); pm_runtime_put_autosuspend(&dev->dev); @@ -1952,10 +1959,9 @@ static void i801_shutdown(struct pci_dev *dev) #ifdef CONFIG_PM_SLEEP static int i801_suspend(struct device *dev) { - struct pci_dev *pci_dev = to_pci_dev(dev); - struct i801_priv *priv = pci_get_drvdata(pci_dev); + struct i801_priv *priv = dev_get_drvdata(dev); - pci_write_config_byte(pci_dev, SMBHSTCFG, priv->original_hstcfg); + pci_write_config_byte(priv->pci_dev, SMBHSTCFG, priv->original_hstcfg); return 0; } @@ -1963,6 +1969,7 @@ static int i801_resume(struct device *dev) { struct i801_priv *priv = dev_get_drvdata(dev); + i801_setup_hstcfg(priv); i801_enable_host_notify(&priv->adapter); return 0; diff --git a/drivers/i2c/busses/i2c-meson.c b/drivers/i2c/busses/i2c-meson.c index c5dec572fc48..ef73a42577cc 100644 --- a/drivers/i2c/busses/i2c-meson.c +++ b/drivers/i2c/busses/i2c-meson.c @@ -5,6 +5,7 @@ * Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com> */ +#include <linux/bitfield.h> #include <linux/clk.h> #include <linux/completion.h> #include <linux/i2c.h> @@ -33,12 +34,17 @@ #define REG_CTRL_ACK_IGNORE BIT(1) #define REG_CTRL_STATUS BIT(2) #define REG_CTRL_ERROR BIT(3) -#define REG_CTRL_CLKDIV_SHIFT 12 -#define REG_CTRL_CLKDIV_MASK GENMASK(21, 12) -#define REG_CTRL_CLKDIVEXT_SHIFT 28 -#define REG_CTRL_CLKDIVEXT_MASK GENMASK(29, 28) +#define REG_CTRL_CLKDIV GENMASK(21, 12) +#define REG_CTRL_CLKDIVEXT GENMASK(29, 28) + +#define REG_SLV_ADDR GENMASK(7, 0) +#define REG_SLV_SDA_FILTER GENMASK(10, 8) +#define REG_SLV_SCL_FILTER GENMASK(13, 11) +#define REG_SLV_SCL_LOW GENMASK(27, 16) +#define REG_SLV_SCL_LOW_EN BIT(28) #define I2C_TIMEOUT_MS 500 +#define FILTER_DELAY 15 enum { TOKEN_END = 0, @@ -133,19 +139,24 @@ static void meson_i2c_set_clk_div(struct meson_i2c *i2c, unsigned int freq) unsigned long clk_rate = clk_get_rate(i2c->clk); unsigned int div; - div = DIV_ROUND_UP(clk_rate, freq * i2c->data->div_factor); + div = DIV_ROUND_UP(clk_rate, freq); + div -= FILTER_DELAY; + div = DIV_ROUND_UP(div, i2c->data->div_factor); /* clock divider has 12 bits */ - if (div >= (1 << 12)) { + if (div > GENMASK(11, 0)) { dev_err(i2c->dev, "requested bus frequency too low\n"); - div = (1 << 12) - 1; + div = GENMASK(11, 0); } - meson_i2c_set_mask(i2c, REG_CTRL, REG_CTRL_CLKDIV_MASK, - (div & GENMASK(9, 0)) << REG_CTRL_CLKDIV_SHIFT); + meson_i2c_set_mask(i2c, REG_CTRL, REG_CTRL_CLKDIV, + FIELD_PREP(REG_CTRL_CLKDIV, div & GENMASK(9, 0))); + + meson_i2c_set_mask(i2c, REG_CTRL, REG_CTRL_CLKDIVEXT, + FIELD_PREP(REG_CTRL_CLKDIVEXT, div >> 10)); - meson_i2c_set_mask(i2c, REG_CTRL, REG_CTRL_CLKDIVEXT_MASK, - (div >> 10) << REG_CTRL_CLKDIVEXT_SHIFT); + /* Disable HIGH/LOW mode */ + meson_i2c_set_mask(i2c, REG_SLAVE_ADDR, REG_SLV_SCL_LOW_EN, 0); dev_dbg(i2c->dev, "%s: clk %lu, freq %u, div %u\n", __func__, clk_rate, freq, div); @@ -280,7 +291,10 @@ static void meson_i2c_do_start(struct meson_i2c *i2c, struct i2c_msg *msg) token = (msg->flags & I2C_M_RD) ? TOKEN_SLAVE_ADDR_READ : TOKEN_SLAVE_ADDR_WRITE; - writel(msg->addr << 1, i2c->regs + REG_SLAVE_ADDR); + + meson_i2c_set_mask(i2c, REG_SLAVE_ADDR, REG_SLV_ADDR, + FIELD_PREP(REG_SLV_ADDR, msg->addr << 1)); + meson_i2c_add_token(i2c, TOKEN_START); meson_i2c_add_token(i2c, token); } @@ -357,16 +371,12 @@ static int meson_i2c_xfer_messages(struct i2c_adapter *adap, struct meson_i2c *i2c = adap->algo_data; int i, ret = 0; - clk_enable(i2c->clk); - for (i = 0; i < num; i++) { ret = meson_i2c_xfer_msg(i2c, msgs + i, i == num - 1, atomic); if (ret) break; } - clk_disable(i2c->clk); - return ret ?: i; } @@ -435,7 +445,7 @@ static int meson_i2c_probe(struct platform_device *pdev) return ret; } - ret = clk_prepare(i2c->clk); + ret = clk_prepare_enable(i2c->clk); if (ret < 0) { dev_err(&pdev->dev, "can't prepare clock\n"); return ret; @@ -457,10 +467,14 @@ static int meson_i2c_probe(struct platform_device *pdev) ret = i2c_add_adapter(&i2c->adap); if (ret < 0) { - clk_unprepare(i2c->clk); + clk_disable_unprepare(i2c->clk); return ret; } + /* Disable filtering */ + meson_i2c_set_mask(i2c, REG_SLAVE_ADDR, + REG_SLV_SDA_FILTER | REG_SLV_SCL_FILTER, 0); + meson_i2c_set_clk_div(i2c, timings.bus_freq_hz); return 0; @@ -471,7 +485,7 @@ static int meson_i2c_remove(struct platform_device *pdev) struct meson_i2c *i2c = platform_get_drvdata(pdev); i2c_del_adapter(&i2c->adap); - clk_unprepare(i2c->clk); + clk_disable_unprepare(i2c->clk); return 0; } diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c index efc14041d45b..0cbdfbe605b5 100644 --- a/drivers/i2c/busses/i2c-mt65xx.c +++ b/drivers/i2c/busses/i2c-mt65xx.c @@ -681,8 +681,8 @@ static int mtk_i2c_calculate_speed(struct mtk_i2c *i2c, unsigned int clk_src, unsigned int cnt_mul; int ret = -EINVAL; - if (target_speed > I2C_MAX_FAST_MODE_PLUS_FREQ) - target_speed = I2C_MAX_FAST_MODE_PLUS_FREQ; + if (target_speed > I2C_MAX_HIGH_SPEED_MODE_FREQ) + target_speed = I2C_MAX_HIGH_SPEED_MODE_FREQ; max_step_cnt = mtk_i2c_max_step_cnt(target_speed); base_step_cnt = max_step_cnt; @@ -759,7 +759,7 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk) for (clk_div = 1; clk_div <= max_clk_div; clk_div++) { clk_src = parent_clk / clk_div; - if (target_speed > I2C_MAX_FAST_MODE_FREQ) { + if (target_speed > I2C_MAX_FAST_MODE_PLUS_FREQ) { /* Set master code speed register */ ret = mtk_i2c_calculate_speed(i2c, clk_src, I2C_MAX_FAST_MODE_FREQ, diff --git a/drivers/i2c/busses/i2c-mxs.c b/drivers/i2c/busses/i2c-mxs.c index 9587347447f0..c4b08a924461 100644 --- a/drivers/i2c/busses/i2c-mxs.c +++ b/drivers/i2c/busses/i2c-mxs.c @@ -25,6 +25,7 @@ #include <linux/of_device.h> #include <linux/dma-mapping.h> #include <linux/dmaengine.h> +#include <linux/dma/mxs-dma.h> #define DRIVER_NAME "mxs-i2c" @@ -200,7 +201,8 @@ static int mxs_i2c_dma_setup_xfer(struct i2c_adapter *adap, dma_map_sg(i2c->dev, &i2c->sg_io[0], 1, DMA_TO_DEVICE); desc = dmaengine_prep_slave_sg(i2c->dmach, &i2c->sg_io[0], 1, DMA_MEM_TO_DEV, - DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + DMA_PREP_INTERRUPT | + MXS_DMA_CTRL_WAIT4END); if (!desc) { dev_err(i2c->dev, "Failed to get DMA data write descriptor.\n"); @@ -228,7 +230,8 @@ static int mxs_i2c_dma_setup_xfer(struct i2c_adapter *adap, dma_map_sg(i2c->dev, &i2c->sg_io[1], 1, DMA_FROM_DEVICE); desc = dmaengine_prep_slave_sg(i2c->dmach, &i2c->sg_io[1], 1, DMA_DEV_TO_MEM, - DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + DMA_PREP_INTERRUPT | + MXS_DMA_CTRL_WAIT4END); if (!desc) { dev_err(i2c->dev, "Failed to get DMA data write descriptor.\n"); @@ -260,7 +263,8 @@ static int mxs_i2c_dma_setup_xfer(struct i2c_adapter *adap, dma_map_sg(i2c->dev, i2c->sg_io, 2, DMA_TO_DEVICE); desc = dmaengine_prep_slave_sg(i2c->dmach, i2c->sg_io, 2, DMA_MEM_TO_DEV, - DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + DMA_PREP_INTERRUPT | + MXS_DMA_CTRL_WAIT4END); if (!desc) { dev_err(i2c->dev, "Failed to get DMA data write descriptor.\n"); diff --git a/drivers/i2c/busses/i2c-npcm7xx.c b/drivers/i2c/busses/i2c-npcm7xx.c index dfcf04e1967f..2ad166355ec9 100644 --- a/drivers/i2c/busses/i2c-npcm7xx.c +++ b/drivers/i2c/busses/i2c-npcm7xx.c @@ -2163,6 +2163,15 @@ static int npcm_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, if (bus->cmd_err == -EAGAIN) ret = i2c_recover_bus(adap); + /* + * After any type of error, check if LAST bit is still set, + * due to a HW issue. + * It cannot be cleared without resetting the module. + */ + if (bus->cmd_err && + (NPCM_I2CRXF_CTL_LAST_PEC & ioread8(bus->reg + NPCM_I2CRXF_CTL))) + npcm_i2c_reset(bus); + #if IS_ENABLED(CONFIG_I2C_SLAVE) /* reenable slave if it was enabled */ if (bus->slave) diff --git a/drivers/i2c/busses/i2c-owl.c b/drivers/i2c/busses/i2c-owl.c index 672f1f239bd6..a163b8f308c1 100644 --- a/drivers/i2c/busses/i2c-owl.c +++ b/drivers/i2c/busses/i2c-owl.c @@ -176,6 +176,9 @@ static irqreturn_t owl_i2c_interrupt(int irq, void *_dev) fifostat = readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT); if (fifostat & OWL_I2C_FIFOSTAT_RNB) { i2c_dev->err = -ENXIO; + /* Clear NACK error bit by writing "1" */ + owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_FIFOSTAT, + OWL_I2C_FIFOSTAT_RNB, true); goto stop; } @@ -183,6 +186,9 @@ static irqreturn_t owl_i2c_interrupt(int irq, void *_dev) stat = readl(i2c_dev->base + OWL_I2C_REG_STAT); if (stat & OWL_I2C_STAT_BEB) { i2c_dev->err = -EIO; + /* Clear BUS error bit by writing "1" */ + owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_STAT, + OWL_I2C_STAT_BEB, true); goto stop; } diff --git a/drivers/i2c/i2c-core-base.c b/drivers/i2c/i2c-core-base.c index 5ec082e2039d..573b5da145d1 100644 --- a/drivers/i2c/i2c-core-base.c +++ b/drivers/i2c/i2c-core-base.c @@ -1464,8 +1464,8 @@ static int i2c_register_adapter(struct i2c_adapter *adap) /* create pre-declared device nodes */ of_i2c_register_devices(adap); - i2c_acpi_register_devices(adap); i2c_acpi_install_space_handler(adap); + i2c_acpi_register_devices(adap); if (adap->nr < __i2c_first_dynamic_bus_num) i2c_scan_static_board_info(adap); |