diff options
Diffstat (limited to 'drivers/ata/libata-core.c')
| -rw-r--r-- | drivers/ata/libata-core.c | 1329 |
1 files changed, 853 insertions, 476 deletions
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 772be09b4689..b05384a8c326 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -59,8 +59,6 @@ #include "libata.h" -#define DRV_VERSION "2.21" /* must be exactly four chars */ - /* debounce timing parameters in msecs { interval, duration, timeout } */ const unsigned long sata_deb_timing_normal[] = { 5, 100, 2000 }; @@ -70,6 +68,7 @@ const unsigned long sata_deb_timing_long[] = { 100, 2000, 5000 }; static unsigned int ata_dev_init_params(struct ata_device *dev, u16 heads, u16 sectors); static unsigned int ata_dev_set_xfermode(struct ata_device *dev); +static unsigned int ata_dev_set_AN(struct ata_device *dev, u8 enable); static void ata_dev_xfermask(struct ata_device *dev); static unsigned long ata_dev_blacklisted(const struct ata_device *dev); @@ -86,6 +85,10 @@ int atapi_dmadir = 0; module_param(atapi_dmadir, int, 0444); MODULE_PARM_DESC(atapi_dmadir, "Enable ATAPI DMADIR bridge support (0=off, 1=on)"); +int atapi_passthru16 = 1; +module_param(atapi_passthru16, int, 0444); +MODULE_PARM_DESC(atapi_passthru16, "Enable ATA_16 passthru for ATAPI devices; on by default (0=off, 1=on)"); + int libata_fua = 0; module_param_named(fua, libata_fua, int, 0444); MODULE_PARM_DESC(fua, "FUA support (0=off, 1=on)"); @@ -94,13 +97,17 @@ static int ata_ignore_hpa = 0; module_param_named(ignore_hpa, ata_ignore_hpa, int, 0644); MODULE_PARM_DESC(ignore_hpa, "Ignore HPA limit (0=keep BIOS limits, 1=ignore limits, using full disk)"); +static int libata_dma_mask = ATA_DMA_MASK_ATA|ATA_DMA_MASK_ATAPI|ATA_DMA_MASK_CFA; +module_param_named(dma, libata_dma_mask, int, 0444); +MODULE_PARM_DESC(dma, "DMA enable/disable (0x1==ATA, 0x2==ATAPI, 0x4==CF)"); + static int ata_probe_timeout = ATA_TMOUT_INTERNAL / HZ; module_param(ata_probe_timeout, int, 0444); MODULE_PARM_DESC(ata_probe_timeout, "Set ATA probing timeout (seconds)"); -int libata_noacpi = 1; +int libata_noacpi = 0; module_param_named(noacpi, libata_noacpi, int, 0444); -MODULE_PARM_DESC(noacpi, "Disables the use of ACPI in suspend/resume when set"); +MODULE_PARM_DESC(noacpi, "Disables the use of ACPI in probe/suspend/resume when set"); MODULE_AUTHOR("Jeff Garzik"); MODULE_DESCRIPTION("Library module for ATA devices"); @@ -235,7 +242,7 @@ static int ata_rwcmd_protocol(struct ata_taskfile *tf, struct ata_device *dev) if (dev->flags & ATA_DFLAG_PIO) { tf->protocol = ATA_PROT_PIO; index = dev->multi_count ? 0 : 8; - } else if (lba48 && (dev->ap->flags & ATA_FLAG_PIO_LBA48)) { + } else if (lba48 && (dev->link->ap->flags & ATA_FLAG_PIO_LBA48)) { /* Unable to use DMA due to host limitation */ tf->protocol = ATA_PROT_PIO; index = dev->multi_count ? 0 : 8; @@ -604,7 +611,7 @@ static const char *sata_spd_string(unsigned int spd) void ata_dev_disable(struct ata_device *dev) { if (ata_dev_enabled(dev)) { - if (ata_msg_drv(dev->ap)) + if (ata_msg_drv(dev->link->ap)) ata_dev_printk(dev, KERN_WARNING, "disabled\n"); ata_down_xfermask_limit(dev, ATA_DNXFER_FORCE_PIO0 | ATA_DNXFER_QUIET); @@ -667,37 +674,57 @@ static unsigned int ata_devchk(struct ata_port *ap, unsigned int device) * None. * * RETURNS: - * Device type, %ATA_DEV_ATA, %ATA_DEV_ATAPI, or %ATA_DEV_UNKNOWN - * the event of failure. + * Device type, %ATA_DEV_ATA, %ATA_DEV_ATAPI, %ATA_DEV_PMP or + * %ATA_DEV_UNKNOWN the event of failure. */ - unsigned int ata_dev_classify(const struct ata_taskfile *tf) { /* Apple's open source Darwin code hints that some devices only * put a proper signature into the LBA mid/high registers, * So, we only check those. It's sufficient for uniqueness. + * + * ATA/ATAPI-7 (d1532v1r1: Feb. 19, 2003) specified separate + * signatures for ATA and ATAPI devices attached on SerialATA, + * 0x3c/0xc3 and 0x69/0x96 respectively. However, SerialATA + * spec has never mentioned about using different signatures + * for ATA/ATAPI devices. Then, Serial ATA II: Port + * Multiplier specification began to use 0x69/0x96 to identify + * port multpliers and 0x3c/0xc3 to identify SEMB device. + * ATA/ATAPI-7 dropped descriptions about 0x3c/0xc3 and + * 0x69/0x96 shortly and described them as reserved for + * SerialATA. + * + * We follow the current spec and consider that 0x69/0x96 + * identifies a port multiplier and 0x3c/0xc3 a SEMB device. */ - - if (((tf->lbam == 0) && (tf->lbah == 0)) || - ((tf->lbam == 0x3c) && (tf->lbah == 0xc3))) { + if ((tf->lbam == 0) && (tf->lbah == 0)) { DPRINTK("found ATA device by sig\n"); return ATA_DEV_ATA; } - if (((tf->lbam == 0x14) && (tf->lbah == 0xeb)) || - ((tf->lbam == 0x69) && (tf->lbah == 0x96))) { + if ((tf->lbam == 0x14) && (tf->lbah == 0xeb)) { DPRINTK("found ATAPI device by sig\n"); return ATA_DEV_ATAPI; } + if ((tf->lbam == 0x69) && (tf->lbah == 0x96)) { + DPRINTK("found PMP device by sig\n"); + return ATA_DEV_PMP; + } + + if ((tf->lbam == 0x3c) && (tf->lbah == 0xc3)) { + printk("ata: SEMB device ignored\n"); + return ATA_DEV_SEMB_UNSUP; /* not yet */ + } + DPRINTK("unknown device\n"); return ATA_DEV_UNKNOWN; } /** * ata_dev_try_classify - Parse returned ATA device signature - * @ap: ATA channel to examine - * @device: Device to examine (starting at zero) + * @dev: ATA device to classify (starting at zero) + * @present: device seems present * @r_err: Value of error register on completion * * After an event -- SRST, E.D.D., or SATA COMRESET -- occurs, @@ -715,15 +742,15 @@ unsigned int ata_dev_classify(const struct ata_taskfile *tf) * RETURNS: * Device type - %ATA_DEV_ATA, %ATA_DEV_ATAPI or %ATA_DEV_NONE. */ - -unsigned int -ata_dev_try_classify(struct ata_port *ap, unsigned int device, u8 *r_err) +unsigned int ata_dev_try_classify(struct ata_device *dev, int present, + u8 *r_err) { + struct ata_port *ap = dev->link->ap; struct ata_taskfile tf; unsigned int class; u8 err; - ap->ops->dev_select(ap, device); + ap->ops->dev_select(ap, dev->devno); memset(&tf, 0, sizeof(tf)); @@ -733,12 +760,12 @@ ata_dev_try_classify(struct ata_port *ap, unsigned int device, u8 *r_err) *r_err = err; /* see if device passed diags: if master then continue and warn later */ - if (err == 0 && device == 0) + if (err == 0 && dev->devno == 0) /* diagnostic fail : do nothing _YET_ */ - ap->device[device].horkage |= ATA_HORKAGE_DIAGNOSTIC; + dev->horkage |= ATA_HORKAGE_DIAGNOSTIC; else if (err == 1) /* do nothing */ ; - else if ((device == 0) && (err == 0x81)) + else if ((dev->devno == 0) && (err == 0x81)) /* do nothing */ ; else return ATA_DEV_NONE; @@ -746,10 +773,20 @@ ata_dev_try_classify(struct ata_port *ap, unsigned int device, u8 *r_err) /* determine if device is ATA or ATAPI */ class = ata_dev_classify(&tf); - if (class == ATA_DEV_UNKNOWN) - return ATA_DEV_NONE; - if ((class == ATA_DEV_ATA) && (ata_chk_status(ap) == 0)) - return ATA_DEV_NONE; + if (class == ATA_DEV_UNKNOWN) { + /* If the device failed diagnostic, it's likely to + * have reported incorrect device signature too. + * Assume ATA device if the device seems present but + * device signature is invalid with diagnostic + * failure. + */ + if (present && (dev->horkage & ATA_HORKAGE_DIAGNOSTIC)) + class = ATA_DEV_ATA; + else + class = ATA_DEV_NONE; + } else if ((class == ATA_DEV_ATA) && (ata_chk_status(ap) == 0)) + class = ATA_DEV_NONE; + return class; } @@ -816,6 +853,21 @@ void ata_id_c_string(const u16 *id, unsigned char *s, *p = '\0'; } +static u64 ata_id_n_sectors(const u16 *id) +{ + if (ata_id_has_lba(id)) { + if (ata_id_has_lba48(id)) + return ata_id_u64(id, 100); + else + return ata_id_u32(id, 60); + } else { + if (ata_id_current_chs_valid(id)) + return ata_id_u32(id, 57); + else + return id[1] * id[3] * id[6]; + } +} + static u64 ata_tf_to_lba48(struct ata_taskfile *tf) { u64 sectors = 0; @@ -843,129 +895,110 @@ static u64 ata_tf_to_lba(struct ata_taskfile *tf) } /** - * ata_read_native_max_address_ext - LBA48 native max query - * @dev: Device to query + * ata_read_native_max_address - Read native max address + * @dev: target device + * @max_sectors: out parameter for the result native max address * - * Perform an LBA48 size query upon the device in question. Return the - * actual LBA48 size or zero if the command fails. - */ - -static u64 ata_read_native_max_address_ext(struct ata_device *dev) -{ - unsigned int err; - struct ata_taskfile tf; - - ata_tf_init(dev, &tf); - - tf.command = ATA_CMD_READ_NATIVE_MAX_EXT; - tf.flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_LBA48 | ATA_TFLAG_ISADDR; - tf.protocol |= ATA_PROT_NODATA; - tf.device |= 0x40; - - err = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0); - if (err) - return 0; - - return ata_tf_to_lba48(&tf); -} - -/** - * ata_read_native_max_address - LBA28 native max query - * @dev: Device to query + * Perform an LBA48 or LBA28 native size query upon the device in + * question. * - * Performa an LBA28 size query upon the device in question. Return the - * actual LBA28 size or zero if the command fails. + * RETURNS: + * 0 on success, -EACCES if command is aborted by the drive. + * -EIO on other errors. */ - -static u64 ata_read_native_max_address(struct ata_device *dev) +static int ata_read_native_max_address(struct ata_device *dev, u64 *max_sectors) { - unsigned int err; + unsigned int err_mask; struct ata_taskfile tf; + int lba48 = ata_id_has_lba48(dev->id); ata_tf_init(dev, &tf); - tf.command = ATA_CMD_READ_NATIVE_MAX; + /* always clear all address registers */ tf.flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_ISADDR; + + if (lba48) { + tf.command = ATA_CMD_READ_NATIVE_MAX_EXT; + tf.flags |= ATA_TFLAG_LBA48; + } else + tf.command = ATA_CMD_READ_NATIVE_MAX; + tf.protocol |= ATA_PROT_NODATA; - tf.device |= 0x40; + tf.device |= ATA_LBA; - err = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0); - if (err) - return 0; + err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0); + if (err_mask) { + ata_dev_printk(dev, KERN_WARNING, "failed to read native " + "max address (err_mask=0x%x)\n", err_mask); + if (err_mask == AC_ERR_DEV && (tf.feature & ATA_ABORTED)) + return -EACCES; + return -EIO; + } - return ata_tf_to_lba(&tf); + if (lba48) + *max_sectors = ata_tf_to_lba48(&tf); + else + *max_sectors = ata_tf_to_lba(&tf); + if (dev->horkage & ATA_HORKAGE_HPA_SIZE) + (*max_sectors)--; + return 0; } /** - * ata_set_native_max_address_ext - LBA48 native max set - * @dev: Device to query + * ata_set_max_sectors - Set max sectors + * @dev: target device * @new_sectors: new max sectors value to set for the device * - * Perform an LBA48 size set max upon the device in question. Return the - * actual LBA48 size or zero if the command fails. + * Set max sectors of @dev to @new_sectors. + * + * RETURNS: + * 0 on success, -EACCES if command is aborted or denied (due to + * previous non-volatile SET_MAX) by the drive. -EIO on other + * errors. */ - -static u64 ata_set_native_max_address_ext(struct ata_device *dev, u64 new_sectors) +static int ata_set_max_sectors(struct ata_device *dev, u64 new_sectors) { - unsigned int err; + unsigned int err_mask; struct ata_taskfile tf; + int lba48 = ata_id_has_lba48(dev->id); new_sectors--; ata_tf_init(dev, &tf); - tf.command = ATA_CMD_SET_MAX_EXT; - tf.flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_LBA48 | ATA_TFLAG_ISADDR; - tf.protocol |= ATA_PROT_NODATA; - tf.device |= 0x40; - - tf.lbal = (new_sectors >> 0) & 0xff; - tf.lbam = (new_sectors >> 8) & 0xff; - tf.lbah = (new_sectors >> 16) & 0xff; - - tf.hob_lbal = (new_sectors >> 24) & 0xff; - tf.hob_lbam = (new_sectors >> 32) & 0xff; - tf.hob_lbah = (new_sectors >> 40) & 0xff; - - err = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0); - if (err) - return 0; - - return ata_tf_to_lba48(&tf); -} - -/** - * ata_set_native_max_address - LBA28 native max set - * @dev: Device to query - * @new_sectors: new max sectors value to set for the device - * - * Perform an LBA28 size set max upon the device in question. Return the - * actual LBA28 size or zero if the command fails. - */ + tf.flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_ISADDR; -static u64 ata_set_native_max_address(struct ata_device *dev, u64 new_sectors) -{ - unsigned int err; - struct ata_taskfile tf; + if (lba48) { + tf.command = ATA_CMD_SET_MAX_EXT; + tf.flags |= ATA_TFLAG_LBA48; - new_sectors--; + tf.hob_lbal = (new_sectors >> 24) & 0xff; + tf.hob_lbam = (new_sectors >> 32) & 0xff; + tf.hob_lbah = (new_sectors >> 40) & 0xff; + } else { + tf.command = ATA_CMD_SET_MAX; - ata_tf_init(dev, &tf); + tf.device |= (new_sectors >> 24) & 0xf; + } - tf.command = ATA_CMD_SET_MAX; - tf.flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_ISADDR; tf.protocol |= ATA_PROT_NODATA; + tf.device |= ATA_LBA; tf.lbal = (new_sectors >> 0) & 0xff; tf.lbam = (new_sectors >> 8) & 0xff; tf.lbah = (new_sectors >> 16) & 0xff; - tf.device |= ((new_sectors >> 24) & 0x0f) | 0x40; - err = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0); - if (err) - return 0; + err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0); + if (err_mask) { + ata_dev_printk(dev, KERN_WARNING, "failed to set " + "max address (err_mask=0x%x)\n", err_mask); + if (err_mask == AC_ERR_DEV && + (tf.feature & (ATA_ABORTED | ATA_IDNF))) + return -EACCES; + return -EIO; + } - return ata_tf_to_lba(&tf); + return 0; } /** @@ -975,60 +1008,93 @@ static u64 ata_set_native_max_address(struct ata_device *dev, u64 new_sectors) * Read the size of an LBA28 or LBA48 disk with HPA features and resize * it if required to the full size of the media. The caller must check * the drive has the HPA feature set enabled. + * + * RETURNS: + * 0 on success, -errno on failure. */ - -static u64 ata_hpa_resize(struct ata_device *dev) +static int ata_hpa_resize(struct ata_device *dev) { - u64 sectors = dev->n_sectors; - u64 hpa_sectors; + struct ata_eh_context *ehc = &dev->link->eh_context; + int print_info = ehc->i.flags & ATA_EHI_PRINTINFO; + u64 sectors = ata_id_n_sectors(dev->id); + u64 native_sectors; + int rc; - if (ata_id_has_lba48(dev->id)) - hpa_sectors = ata_read_native_max_address_ext(dev); - else - hpa_sectors = ata_read_native_max_address(dev); + /* do we need to do it? */ + if (dev->class != ATA_DEV_ATA || + !ata_id_has_lba(dev->id) || !ata_id_hpa_enabled(dev->id) || + (dev->horkage & ATA_HORKAGE_BROKEN_HPA)) + return 0; - if (hpa_sectors > sectors) { - ata_dev_printk(dev, KERN_INFO, - "Host Protected Area detected:\n" - "\tcurrent size: %lld sectors\n" - "\tnative size: %lld sectors\n", - (long long)sectors, (long long)hpa_sectors); - - if (ata_ignore_hpa) { - if (ata_id_has_lba48(dev->id)) - hpa_sectors = ata_set_native_max_address_ext(dev, hpa_sectors); - else - hpa_sectors = ata_set_native_max_address(dev, - hpa_sectors); - - if (hpa_sectors) { - ata_dev_printk(dev, KERN_INFO, "native size " - "increased to %lld sectors\n", - (long long)hpa_sectors); - return hpa_sectors; - } + /* read native max address */ + rc = ata_read_native_max_address(dev, &native_sectors); + if (rc) { + /* If HPA isn't going to be unlocked, skip HPA + * resizing from the next try. + */ + if (!ata_ignore_hpa) { + ata_dev_printk(dev, KERN_WARNING, "HPA support seems " + "broken, will skip HPA handling\n"); + dev->horkage |= ATA_HORKAGE_BROKEN_HPA; + + /* we can continue if device aborted the command */ + if (rc == -EACCES) + rc = 0; } - } else if (hpa_sectors < sectors) - ata_dev_printk(dev, KERN_WARNING, "%s 1: hpa sectors (%lld) " - "is smaller than sectors (%lld)\n", __FUNCTION__, - (long long)hpa_sectors, (long long)sectors); - return sectors; -} + return rc; + } -static u64 ata_id_n_sectors(const u16 *id) -{ - if (ata_id_has_lba(id)) { - if (ata_id_has_lba48(id)) - return ata_id_u64(id, 100); - else - return ata_id_u32(id, 60); - } else { - if (ata_id_current_chs_valid(id)) - return ata_id_u32(id, 57); - else - return id[1] * id[3] * id[6]; + /* nothing to do? */ + if (native_sectors <= sectors || !ata_ignore_hpa) { + if (!print_info || native_sectors == sectors) + return 0; + + if (native_sectors > sectors) + ata_dev_printk(dev, KERN_INFO, + "HPA detected: current %llu, native %llu\n", + (unsigned long long)sectors, + (unsigned long long)native_sectors); + else if (native_sectors < sectors) + ata_dev_printk(dev, KERN_WARNING, + "native sectors (%llu) is smaller than " + "sectors (%llu)\n", + (unsigned long long)native_sectors, + (unsigned long long)sectors); + return 0; } + + /* let's unlock HPA */ + rc = ata_set_max_sectors(dev, native_sectors); + if (rc == -EACCES) { + /* if device aborted the command, skip HPA resizing */ + ata_dev_printk(dev, KERN_WARNING, "device aborted resize " + "(%llu -> %llu), skipping HPA handling\n", + (unsigned long long)sectors, + (unsigned long long)native_sectors); + dev->horkage |= ATA_HORKAGE_BROKEN_HPA; + return 0; + } else if (rc) + return rc; + + /* re-read IDENTIFY data */ + rc = ata_dev_reread_id(dev, 0); + if (rc) { + ata_dev_printk(dev, KERN_ERR, "failed to re-read IDENTIFY " + "data after HPA resizing\n"); + return rc; + } + + if (print_info) { + u64 new_sectors = ata_id_n_sectors(dev->id); + ata_dev_printk(dev, KERN_INFO, + "HPA unlocked: %llu -> %llu, native %llu\n", + (unsigned long long)sectors, + (unsigned long long)new_sectors, + (unsigned long long)native_sectors); + } + + return 0; } /** @@ -1150,7 +1216,7 @@ void ata_dev_select(struct ata_port *ap, unsigned int device, ap->ops->dev_select(ap, device); if (wait) { - if (can_sleep && ap->device[device].class == ATA_DEV_ATAPI) + if (can_sleep && ap->link.device[device].class == ATA_DEV_ATAPI) msleep(150); ata_wait_idle(ap); } @@ -1328,6 +1394,7 @@ static void ata_qc_complete_internal(struct ata_queued_cmd *qc) * @dma_dir: Data tranfer direction of the command * @sg: sg list for the data buffer of the command * @n_elem: Number of sg entries + * @timeout: Timeout in msecs (0 for default) * * Executes libata internal command with timeout. @tf contains * command on entry and result on return. Timeout and error @@ -1344,13 +1411,15 @@ static void ata_qc_complete_internal(struct ata_queued_cmd *qc) unsigned ata_exec_internal_sg(struct ata_device *dev, struct ata_taskfile *tf, const u8 *cdb, int dma_dir, struct scatterlist *sg, - unsigned int n_elem) + unsigned int n_elem, unsigned long timeout) { - struct ata_port *ap = dev->ap; + struct ata_link *link = dev->link; + struct ata_port *ap = link->ap; u8 command = tf->command; struct ata_queued_cmd *qc; unsigned int tag, preempted_tag; u32 preempted_sactive, preempted_qc_active; + int preempted_nr_active_links; DECLARE_COMPLETION_ONSTACK(wait); unsigned long flags; unsigned int err_mask; @@ -1386,12 +1455,14 @@ unsigned ata_exec_internal_sg(struct ata_device *dev, qc->dev = dev; ata_qc_reinit(qc); - preempted_tag = ap->active_tag; - preempted_sactive = ap->sactive; + preempted_tag = link->active_tag; + preempted_sactive = link->sactive; preempted_qc_active = ap->qc_active; - ap->active_tag = ATA_TAG_POISON; - ap->sactive = 0; + preempted_nr_active_links = ap->nr_active_links; + link->active_tag = ATA_TAG_POISON; + link->sactive = 0; ap->qc_active = 0; + ap->nr_active_links = 0; /* prepare & issue qc */ qc->tf = *tf; @@ -1416,7 +1487,10 @@ unsigned ata_exec_internal_sg(struct ata_device *dev, spin_unlock_irqrestore(ap->lock, flags); - rc = wait_for_completion_timeout(&wait, ata_probe_timeout); + if (!timeout) + timeout = ata_probe_timeout * 1000 / HZ; + + rc = wait_for_completion_timeout(&wait, msecs_to_jiffies(timeout)); ata_port_flush_task(ap); @@ -1467,9 +1541,10 @@ unsigned ata_exec_internal_sg(struct ata_device *dev, err_mask = qc->err_mask; ata_qc_free(qc); - ap->active_tag = preempted_tag; - ap->sactive = preempted_sactive; + link->active_tag = preempted_tag; + link->sactive = preempted_sactive; ap->qc_active = preempted_qc_active; + ap->nr_active_links = preempted_nr_active_links; /* XXX - Some LLDDs (sata_mv) disable port on command failure. * Until those drivers are fixed, we detect the condition @@ -1500,6 +1575,7 @@ unsigned ata_exec_internal_sg(struct ata_device *dev, * @dma_dir: Data tranfer direction of the command * @buf: Data buffer of the command * @buflen: Length of data buffer + * @timeout: Timeout in msecs (0 for default) * * Wrapper around ata_exec_internal_sg() which takes simple * buffer instead of sg list. @@ -1512,7 +1588,8 @@ unsigned ata_exec_internal_sg(struct ata_device *dev, */ unsigned ata_exec_internal(struct ata_device *dev, struct ata_taskfile *tf, const u8 *cdb, - int dma_dir, void *buf, unsigned int buflen) + int dma_dir, void *buf, unsigned int buflen, + unsigned long timeout) { struct scatterlist *psg = NULL, sg; unsigned int n_elem = 0; @@ -1524,7 +1601,8 @@ unsigned ata_exec_internal(struct ata_device *dev, n_elem++; } - return ata_exec_internal_sg(dev, tf, cdb, dma_dir, psg, n_elem); + return ata_exec_internal_sg(dev, tf, cdb, dma_dir, psg, n_elem, + timeout); } /** @@ -1551,7 +1629,7 @@ unsigned int ata_do_simple_cmd(struct ata_device *dev, u8 cmd) tf.flags |= ATA_TFLAG_DEVICE; tf.protocol = ATA_PROT_NODATA; - return ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0); + return ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0); } /** @@ -1566,7 +1644,7 @@ unsigned int ata_pio_need_iordy(const struct ata_device *adev) { /* Controller doesn't support IORDY. Probably a pointless check as the caller should know this */ - if (adev->ap->flags & ATA_FLAG_NO_IORDY) + if (adev->link->ap->flags & ATA_FLAG_NO_IORDY) return 0; /* PIO3 and higher it is mandatory */ if (adev->pio_mode > XFER_PIO_2) @@ -1613,6 +1691,9 @@ static u32 ata_pio_mask_no_iordy(const struct ata_device *adev) * devices. This function also issues ATA_CMD_INIT_DEV_PARAMS * for pre-ATA4 drives. * + * FIXME: ATA_CMD_ID_ATA is optional for early drives and right + * now we abort if we hit that case. + * * LOCKING: * Kernel thread context (may sleep) * @@ -1622,7 +1703,7 @@ static u32 ata_pio_mask_no_iordy(const struct ata_device *adev) int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class, unsigned int flags, u16 *id) { - struct ata_port *ap = dev->ap; + struct ata_port *ap = dev->link->ap; unsigned int class = *p_class; struct ata_taskfile tf; unsigned int err_mask = 0; @@ -1663,7 +1744,7 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class, tf.flags |= ATA_TFLAG_POLLING; err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE, - id, sizeof(id[0]) * ATA_ID_WORDS); + id, sizeof(id[0]) * ATA_ID_WORDS, 0); if (err_mask) { if (err_mask & AC_ERR_NODEV_HINT) { DPRINTK("ata%u.%d: NODEV after polling detection\n", @@ -1722,7 +1803,8 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class, tf.feature = SETFEATURES_SPINUP; tf.protocol = ATA_PROT_NODATA; tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; - err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0); + err_mask = ata_exec_internal(dev, &tf, NULL, + DMA_NONE, NULL, 0, 0); if (err_mask && id[2] != 0x738c) { rc = -EIO; reason = "SPINUP failed"; @@ -1740,10 +1822,13 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class, /* * The exact sequence expected by certain pre-ATA4 drives is: * SRST RESET - * IDENTIFY - * INITIALIZE DEVICE PARAMETERS + * IDENTIFY (optional in early ATA) + * INITIALIZE DEVICE PARAMETERS (later IDE and ATA) * anything else.. * Some drives were very specific about that exact sequence. + * + * Note that ATA4 says lba is mandatory so the second check + * shoud never trigger. */ if (ata_id_major_version(id) < 4 || !ata_id_has_lba(id)) { err_mask = ata_dev_init_params(dev, id[3], id[6]); @@ -1774,13 +1859,14 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class, static inline u8 ata_dev_knobble(struct ata_device *dev) { - return ((dev->ap->cbl == ATA_CBL_SATA) && (!ata_id_is_sata(dev->id))); + struct ata_port *ap = dev->link->ap; + return ((ap->cbl == ATA_CBL_SATA) && (!ata_id_is_sata(dev->id))); } static void ata_dev_config_ncq(struct ata_device *dev, char *desc, size_t desc_sz) { - struct ata_port *ap = dev->ap; + struct ata_port *ap = dev->link->ap; int hdepth = 0, ddepth = ata_id_queue_depth(dev->id); if (!ata_id_has_ncq(dev->id)) { @@ -1817,8 +1903,8 @@ static void ata_dev_config_ncq(struct ata_device *dev, */ int ata_dev_configure(struct ata_device *dev) { - struct ata_port *ap = dev->ap; - struct ata_eh_context *ehc = &ap->eh_context; + struct ata_port *ap = dev->link->ap; + struct ata_eh_context *ehc = &dev->link->eh_context; int print_info = ehc->i.flags & ATA_EHI_PRINTINFO; const u16 *id = dev->id; unsigned int xfer_mask; @@ -1844,6 +1930,11 @@ int ata_dev_configure(struct ata_device *dev) if (rc) return rc; + /* massage HPA, do it early as it might change IDENTIFY data */ + rc = ata_hpa_resize(dev); + if (rc) + return rc; + /* print device capabilities */ if (ata_msg_probe(ap)) ata_dev_printk(dev, KERN_DEBUG, @@ -1911,10 +2002,6 @@ int ata_dev_configure(struct ata_device *dev) dev->flags |= ATA_DFLAG_FLUSH_EXT; } - if (!(dev->horkage & ATA_HORKAGE_BROKEN_HPA) && - ata_id_hpa_enabled(dev->id)) - dev->n_sectors = ata_hpa_resize(dev); - /* config NCQ */ ata_dev_config_ncq(dev, ncq_desc, sizeof(ncq_desc)); @@ -1963,7 +2050,9 @@ int ata_dev_configure(struct ata_device *dev) /* ATAPI-specific feature tests */ else if (dev->class == ATA_DEV_ATAPI) { - char *cdb_intr_string = ""; + const char *cdb_intr_string = ""; + const char *atapi_an_string = ""; + u32 sntf; rc = atapi_cdb_len(id); if ((rc < 12) || (rc > ATAPI_CDB_LEN)) { @@ -1975,6 +2064,28 @@ int ata_dev_configure(struct ata_device *dev) } dev->cdb_len = (unsigned int) rc; + /* Enable ATAPI AN if both the host and device have + * the support. If PMP is attached, SNTF is required + * to enable ATAPI AN to discern between PHY status + * changed notifications and ATAPI ANs. + */ + if ((ap->flags & ATA_FLAG_AN) && ata_id_has_atapi_AN(id) && + (!ap->nr_pmp_links || + sata_scr_read(&ap->link, SCR_NOTIFICATION, &sntf) == 0)) { + unsigned int err_mask; + + /* issue SET feature command to turn this on */ + err_mask = ata_dev_set_AN(dev, SETFEATURES_SATA_ENABLE); + if (err_mask) + ata_dev_printk(dev, KERN_ERR, + "failed to enable ATAPI AN " + "(err_mask=0x%x)\n", err_mask); + else { + dev->flags |= ATA_DFLAG_AN; + atapi_an_string = ", ATAPI AN"; + } + } + if (ata_id_cdb_intr(dev->id)) { dev->flags |= ATA_DFLAG_CDB_INTR; cdb_intr_string = ", CDB intr"; @@ -1983,10 +2094,10 @@ int ata_dev_configure(struct ata_device *dev) /* print device info to dmesg */ if (ata_msg_drv(ap) && print_info) ata_dev_printk(dev, KERN_INFO, - "ATAPI: %s, %s, max %s%s\n", + "ATAPI: %s, %s, max %s%s%s\n", modelbuf, fwrevbuf, ata_mode_string(xfer_mask), - cdb_intr_string); + cdb_intr_string, atapi_an_string); } /* determine max_sectors */ @@ -2103,21 +2214,19 @@ int ata_bus_probe(struct ata_port *ap) { unsigned int classes[ATA_MAX_DEVICES]; int tries[ATA_MAX_DEVICES]; - int i, rc; + int rc; struct ata_device *dev; ata_port_probe(ap); - for (i = 0; i < ATA_MAX_DEVICES; i++) - tries[i] = ATA_PROBE_MAX_TRIES; + ata_link_for_each_dev(dev, &ap->link) + tries[dev->devno] = ATA_PROBE_MAX_TRIES; retry: /* reset and determine device classes */ ap->ops->phy_reset(ap); - for (i = 0; i < ATA_MAX_DEVICES; i++) { - dev = &ap->device[i]; - + ata_link_for_each_dev(dev, &ap->link) { if (!(ap->flags & ATA_FLAG_DISABLED) && dev->class != ATA_DEV_UNKNOWN) classes[dev->devno] = dev->class; @@ -2132,18 +2241,16 @@ int ata_bus_probe(struct ata_port *ap) /* after the reset the device state is PIO 0 and the controller state is undefined. Record the mode */ - for (i = 0; i < ATA_MAX_DEVICES; i++) - ap->device[i].pio_mode = XFER_PIO_0; + ata_link_for_each_dev(dev, &ap->link) + dev->pio_mode = XFER_PIO_0; /* read IDENTIFY page and configure devices. We have to do the identify specific sequence bass-ackwards so that PDIAG- is released by the slave device */ - for (i = ATA_MAX_DEVICES - 1; i >= 0; i--) { - dev = &ap->device[i]; - - if (tries[i]) - dev->class = classes[i]; + ata_link_for_each_dev(dev, &ap->link) { + if (tries[dev->devno]) + dev->class = classes[dev->devno]; if (!ata_dev_enabled(dev)) continue; @@ -2158,33 +2265,42 @@ int ata_bus_probe(struct ata_port *ap) if (ap->ops->cable_detect) ap->cbl = ap->ops->cable_detect(ap); + /* We may have SATA bridge glue hiding here irrespective of the + reported cable types and sensed types */ + ata_link_for_each_dev(dev, &ap->link) { + if (!ata_dev_enabled(dev)) + continue; + /* SATA drives indicate we have a bridge. We don't know which + end of the link the bridge is which is a problem */ + if (ata_id_is_sata(dev->id)) + ap->cbl = ATA_CBL_SATA; + } + /* After the identify sequence we can now set up the devices. We do this in the normal order so that the user doesn't get confused */ - for(i = 0; i < ATA_MAX_DEVICES; i++) { - dev = &ap->device[i]; + ata_link_for_each_dev(dev, &ap->link) { if (!ata_dev_enabled(dev)) continue; - ap->eh_context.i.flags |= ATA_EHI_PRINTINFO; + ap->link.eh_context.i.flags |= ATA_EHI_PRINTINFO; rc = ata_dev_configure(dev); - ap->eh_context.i.flags &= ~ATA_EHI_PRINTINFO; + ap->link.eh_context.i.flags &= ~ATA_EHI_PRINTINFO; if (rc) goto fail; } /* configure transfer mode */ - rc = ata_set_mode(ap, &dev); + rc = ata_set_mode(&ap->link, &dev); if (rc) goto fail; - for (i = 0; i < ATA_MAX_DEVICES; i++) - if (ata_dev_enabled(&ap->device[i])) + ata_link_for_each_dev(dev, &ap->link) + if (ata_dev_enabled(dev)) return 0; /* no device present, disable port */ ata_port_disable(ap); - ap->ops->port_disable(ap); return -ENODEV; fail: @@ -2204,7 +2320,7 @@ int ata_bus_probe(struct ata_port *ap) /* This is the last chance, better to slow * down than lose it. */ - sata_down_spd_limit(ap); + sata_down_spd_limit(&ap->link); ata_down_xfermask_limit(dev, ATA_DNXFER_PIO); } } @@ -2233,28 +2349,28 @@ void ata_port_probe(struct ata_port *ap) /** * sata_print_link_status - Print SATA link status - * @ap: SATA port to printk link status about + * @link: SATA link to printk link status about * * This function prints link speed and status of a SATA link. * * LOCKING: * None. */ -void sata_print_link_status(struct ata_port *ap) +void sata_print_link_status(struct ata_link *link) { u32 sstatus, scontrol, tmp; - if (sata_scr_read(ap, SCR_STATUS, &sstatus)) + if (sata_scr_read(link, SCR_STATUS, &sstatus)) return; - sata_scr_read(ap, SCR_CONTROL, &scontrol); + sata_scr_read(link, SCR_CONTROL, &scontrol); - if (ata_port_online(ap)) { + if (ata_link_online(link)) { tmp = (sstatus >> 4) & 0xf; - ata_port_printk(ap, KERN_INFO, + ata_link_printk(link, KERN_INFO, "SATA link up %s (SStatus %X SControl %X)\n", sata_spd_string(tmp), sstatus, scontrol); } else { - ata_port_printk(ap, KERN_INFO, + ata_link_printk(link, KERN_INFO, "SATA link down (SStatus %X SControl %X)\n", sstatus, scontrol); } @@ -2274,32 +2390,33 @@ void sata_print_link_status(struct ata_port *ap) */ void __sata_phy_reset(struct ata_port *ap) { - u32 sstatus; + struct ata_link *link = &ap->link; unsigned long timeout = jiffies + (HZ * 5); + u32 sstatus; if (ap->flags & ATA_FLAG_SATA_RESET) { /* issue phy wake/reset */ - sata_scr_write_flush(ap, SCR_CONTROL, 0x301); + sata_scr_write_flush(link, SCR_CONTROL, 0x301); /* Couldn't find anything in SATA I/II specs, but * AHCI-1.1 10.4.2 says at least 1 ms. */ mdelay(1); } /* phy wake/clear reset */ - sata_scr_write_flush(ap, SCR_CONTROL, 0x300); + sata_scr_write_flush(link, SCR_CONTROL, 0x300); /* wait for phy to become ready, if necessary */ do { msleep(200); - sata_scr_read(ap, SCR_STATUS, &sstatus); + sata_scr_read(link, SCR_STATUS, &sstatus); if ((sstatus & 0xf) != 1) break; } while (time_before(jiffies, timeout)); /* print link status */ - sata_print_link_status(ap); + sata_print_link_status(link); /* TODO: phy layer with polling, timeouts, etc. */ - if (!ata_port_offline(ap)) + if (!ata_link_offline(link)) ata_port_probe(ap); else ata_port_disable(ap); @@ -2344,8 +2461,8 @@ void sata_phy_reset(struct ata_port *ap) struct ata_device *ata_dev_pair(struct ata_device *adev) { - struct ata_port *ap = adev->ap; - struct ata_device *pair = &ap->device[1 - adev->devno]; + struct ata_link *link = adev->link; + struct ata_device *pair = &link->device[1 - adev->devno]; if (!ata_dev_enabled(pair)) return NULL; return pair; @@ -2366,16 +2483,16 @@ struct ata_device *ata_dev_pair(struct ata_device *adev) void ata_port_disable(struct ata_port *ap) { - ap->device[0].class = ATA_DEV_NONE; - ap->device[1].class = ATA_DEV_NONE; + ap->link.device[0].class = ATA_DEV_NONE; + ap->link.device[1].class = ATA_DEV_NONE; ap->flags |= ATA_FLAG_DISABLED; } /** * sata_down_spd_limit - adjust SATA spd limit downward - * @ap: Port to adjust SATA spd limit for + * @link: Link to adjust SATA spd limit for * - * Adjust SATA spd limit of @ap downward. Note that this + * Adjust SATA spd limit of @link downward. Note that this * function only adjusts the limit. The change must be applied * using sata_set_spd(). * @@ -2385,24 +2502,24 @@ void ata_port_disable(struct ata_port *ap) * RETURNS: * 0 on success, negative errno on failure */ -int sata_down_spd_limit(struct ata_port *ap) +int sata_down_spd_limit(struct ata_link *link) { u32 sstatus, spd, mask; int rc, highbit; - if (!sata_scr_valid(ap)) + if (!sata_scr_valid(link)) return -EOPNOTSUPP; /* If SCR can be read, use it to determine the current SPD. - * If not, use cached value in ap->sata_spd. + * If not, use cached value in link->sata_spd. */ - rc = sata_scr_read(ap, SCR_STATUS, &sstatus); + rc = sata_scr_read(link, SCR_STATUS, &sstatus); if (rc == 0) spd = (sstatus >> 4) & 0xf; else - spd = ap->sata_spd; + spd = link->sata_spd; - mask = ap->sata_spd_limit; + mask = link->sata_spd_limit; if (mask <= 1) return -EINVAL; @@ -2422,22 +2539,22 @@ int sata_down_spd_limit(struct ata_port *ap) if (!mask) return -EINVAL; - ap->sata_spd_limit = mask; + link->sata_spd_limit = mask; - ata_port_printk(ap, KERN_WARNING, "limiting SATA link speed to %s\n", + ata_link_printk(link, KERN_WARNING, "limiting SATA link speed to %s\n", sata_spd_string(fls(mask))); return 0; } -static int __sata_set_spd_needed(struct ata_port *ap, u32 *scontrol) +static int __sata_set_spd_needed(struct ata_link *link, u32 *scontrol) { u32 spd, limit; - if (ap->sata_spd_limit == UINT_MAX) + if (link->sata_spd_limit == UINT_MAX) limit = 0; else - limit = fls(ap->sata_spd_limit); + limit = fls(link->sata_spd_limit); spd = (*scontrol >> 4) & 0xf; *scontrol = (*scontrol & ~0xf0) | ((limit & 0xf) << 4); @@ -2447,10 +2564,10 @@ static int __sata_set_spd_needed(struct ata_port *ap, u32 *scontrol) /** * sata_set_spd_needed - is SATA spd configuration needed - * @ap: Port in question + * @link: Link in question * * Test whether the spd limit in SControl matches - * @ap->sata_spd_limit. This function is used to determine + * @link->sata_spd_limit. This function is used to determine * whether hardreset is necessary to apply SATA spd * configuration. * @@ -2460,21 +2577,21 @@ static int __sata_set_spd_needed(struct ata_port *ap, u32 *scontrol) * RETURNS: * 1 if SATA spd configuration is needed, 0 otherwise. */ -int sata_set_spd_needed(struct ata_port *ap) +int sata_set_spd_needed(struct ata_link *link) { u32 scontrol; - if (sata_scr_read(ap, SCR_CONTROL, &scontrol)) + if (sata_scr_read(link, SCR_CONTROL, &scontrol)) return 0; - return __sata_set_spd_needed(ap, &scontrol); + return __sata_set_spd_needed(link, &scontrol); } /** * sata_set_spd - set SATA spd according to spd limit - * @ap: Port to set SATA spd for + * @link: Link to set SATA spd for * - * Set SATA spd of @ap according to sata_spd_limit. + * Set SATA spd of @link according to sata_spd_limit. * * LOCKING: * Inherited from caller. @@ -2483,18 +2600,18 @@ int sata_set_spd_needed(struct ata_port *ap) * 0 if spd doesn't need to be changed, 1 if spd has been * changed. Negative errno if SCR registers are inaccessible. */ -int sata_set_spd(struct ata_port *ap) +int sata_set_spd(struct ata_link *link) { u32 scontrol; int rc; - if ((rc = sata_scr_read(ap, SCR_CONTROL, &scontrol))) + if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol))) return rc; - if (!__sata_set_spd_needed(ap, &scontrol)) + if (!__sata_set_spd_needed(link, &scontrol)) return 0; - if ((rc = sata_scr_write(ap, SCR_CONTROL, scontrol))) + if ((rc = sata_scr_write(link, SCR_CONTROL, scontrol))) return rc; return 1; @@ -2749,7 +2866,7 @@ int ata_down_xfermask_limit(struct ata_device *dev, unsigned int sel) static int ata_dev_set_mode(struct ata_device *dev) { - struct ata_eh_context *ehc = &dev->ap->eh_context; + struct ata_eh_context *ehc = &dev->link->eh_context; unsigned int err_mask; int rc; @@ -2761,7 +2878,11 @@ static int ata_dev_set_mode(struct ata_device *dev) /* Old CFA may refuse this command, which is just fine */ if (dev->xfer_shift == ATA_SHIFT_PIO && ata_id_is_cfa(dev->id)) err_mask &= ~AC_ERR_DEV; - + /* Some very old devices and some bad newer ones fail any kind of + SET_XFERMODE request but support PIO0-2 timings and no IORDY */ + if (dev->xfer_shift == ATA_SHIFT_PIO && !ata_id_has_iordy(dev->id) && + dev->pio_mode <= XFER_PIO_2) + err_mask &= ~AC_ERR_DEV; if (err_mask) { ata_dev_printk(dev, KERN_ERR, "failed to set xfermode " "(err_mask=0x%x)\n", err_mask); @@ -2769,7 +2890,7 @@ static int ata_dev_set_mode(struct ata_device *dev) } ehc->i.flags |= ATA_EHI_POST_SETMODE; - rc = ata_dev_revalidate(dev, 0); + rc = ata_dev_revalidate(dev, ATA_DEV_UNKNOWN, 0); ehc->i.flags &= ~ATA_EHI_POST_SETMODE; if (rc) return rc; @@ -2784,7 +2905,7 @@ static int ata_dev_set_mode(struct ata_device *dev) /** * ata_do_set_mode - Program timings and issue SET FEATURES - XFER - * @ap: port on which timings will be programmed + * @link: link on which timings will be programmed * @r_failed_dev: out paramter for failed device * * Standard implementation of the function used to tune and set @@ -2799,25 +2920,36 @@ static int ata_dev_set_mode(struct ata_device *dev) * 0 on success, negative errno otherwise */ -int ata_do_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev) +int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev) { + struct ata_port *ap = link->ap; struct ata_device *dev; - int i, rc = 0, used_dma = 0, found = 0; - + int rc = 0, used_dma = 0, found = 0; /* step 1: calculate xfer_mask */ - for (i = 0; i < ATA_MAX_DEVICES; i++) { + ata_link_for_each_dev(dev, link) { unsigned int pio_mask, dma_mask; - - dev = &ap->device[i]; + unsigned int mode_mask; if (!ata_dev_enabled(dev)) continue; + mode_mask = ATA_DMA_MASK_ATA; + if (dev->class == ATA_DEV_ATAPI) + mode_mask = ATA_DMA_MASK_ATAPI; + else if (ata_id_is_cfa(dev->id)) + mode_mask = ATA_DMA_MASK_CFA; + ata_dev_xfermask(dev); pio_mask = ata_pack_xfermask(dev->pio_mask, 0, 0); dma_mask = ata_pack_xfermask(0, dev->mwdma_mask, dev->udma_mask); + + if (libata_dma_mask & mode_mask) + dma_mask = ata_pack_xfermask(0, dev->mwdma_mask, dev->udma_mask); + else + dma_mask = 0; + dev->pio_mode = ata_xfer_mask2mode(pio_mask); dev->dma_mode = ata_xfer_mask2mode(dma_mask); @@ -2829,8 +2961,7 @@ int ata_do_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev) goto out; /* step 2: always set host PIO timings */ - for (i = 0; i < ATA_MAX_DEVICES; i++) { - dev = &ap->device[i]; + ata_link_for_each_dev(dev, link) { if (!ata_dev_enabled(dev)) continue; @@ -2847,9 +2978,7 @@ int ata_do_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev) } /* step 3: set host DMA timings */ - for (i = 0; i < ATA_MAX_DEVICES; i++) { - dev = &ap->device[i]; - + ata_link_for_each_dev(dev, link) { if (!ata_dev_enabled(dev) || !dev->dma_mode) continue; @@ -2860,9 +2989,7 @@ int ata_do_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev) } /* step 4: update devices' xfer mode */ - for (i = 0; i < ATA_MAX_DEVICES; i++) { - dev = &ap->device[i]; - + ata_link_for_each_dev(dev, link) { /* don't update suspended devices' xfer mode */ if (!ata_dev_enabled(dev)) continue; @@ -2886,7 +3013,7 @@ int ata_do_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev) /** * ata_set_mode - Program timings and issue SET FEATURES - XFER - * @ap: port on which timings will be programmed + * @link: link on which timings will be programmed * @r_failed_dev: out paramter for failed device * * Set ATA device disk transfer mode (PIO3, UDMA6, etc.). If @@ -2899,12 +3026,14 @@ int ata_do_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev) * RETURNS: * 0 on success, negative errno otherwise */ -int ata_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev) +int ata_set_mode(struct ata_link *link, struct ata_device **r_failed_dev) { + struct ata_port *ap = link->ap; + /* has private set_mode? */ if (ap->ops->set_mode) - return ap->ops->set_mode(ap, r_failed_dev); - return ata_do_set_mode(ap, r_failed_dev); + return ap->ops->set_mode(link, r_failed_dev); + return ata_do_set_mode(link, r_failed_dev); } /** @@ -3007,7 +3136,7 @@ int ata_wait_ready(struct ata_port *ap, unsigned long deadline) if (!(status & ATA_BUSY)) return 0; - if (!ata_port_online(ap) && status == 0xff) + if (!ata_link_online(&ap->link) && status == 0xff) return -ENODEV; if (time_after(now, deadline)) return -EBUSY; @@ -3088,6 +3217,8 @@ static int ata_bus_softreset(struct ata_port *ap, unsigned int devmask, unsigned long deadline) { struct ata_ioports *ioaddr = &ap->ioaddr; + struct ata_device *dev; + int i = 0; DPRINTK("ata%u: bus reset via SRST\n", ap->print_id); @@ -3098,6 +3229,25 @@ static int ata_bus_softreset(struct ata_port *ap, unsigned int devmask, udelay(20); /* FIXME: flush */ iowrite8(ap->ctl, ioaddr->ctl_addr); + /* If we issued an SRST then an ATA drive (not ATAPI) + * may have changed configuration and be in PIO0 timing. If + * we did a hard reset (or are coming from power on) this is + * true for ATA or ATAPI. Until we've set a suitable controller + * mode we should not touch the bus as we may be talking too fast. + */ + + ata_link_for_each_dev(dev, &ap->link) + dev->pio_mode = XFER_PIO_0; + + /* If the controller has a pio mode setup function then use + it to set the chipset to rights. Don't touch the DMA setup + as that will be dealt with when revalidating */ + if (ap->ops->set_piomode) { + ata_link_for_each_dev(dev, &ap->link) + if (devmask & (1 << i++)) + ap->ops->set_piomode(ap, dev); + } + /* spec mandates ">= 2ms" before checking status. * We wait 150ms, because that was the magic delay used for * ATAPI devices in Hale Landis's ATADRVR, for the period of time @@ -3142,6 +3292,7 @@ static int ata_bus_softreset(struct ata_port *ap, unsigned int devmask, void ata_bus_reset(struct ata_port *ap) { + struct ata_device *device = ap->link.device; struct ata_ioports *ioaddr = &ap->ioaddr; unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS; u8 err; @@ -3177,19 +3328,19 @@ void ata_bus_reset(struct ata_port *ap) /* * determine by signature whether we have ATA or ATAPI devices */ - ap->device[0].class = ata_dev_try_classify(ap, 0, &err); + device[0].class = ata_dev_try_classify(&device[0], dev0, &err); if ((slave_possible) && (err != 0x81)) - ap->device[1].class = ata_dev_try_classify(ap, 1, &err); + device[1].class = ata_dev_try_classify(&device[1], dev1, &err); /* is double-select really necessary? */ - if (ap->device[1].class != ATA_DEV_NONE) + if (device[1].class != ATA_DEV_NONE) ap->ops->dev_select(ap, 1); - if (ap->device[0].class != ATA_DEV_NONE) + if (device[0].class != ATA_DEV_NONE) ap->ops->dev_select(ap, 0); /* if no devices were detected, disable this port */ - if ((ap->device[0].class == ATA_DEV_NONE) && - (ap->device[1].class == ATA_DEV_NONE)) + if ((device[0].class == ATA_DEV_NONE) && + (device[1].class == ATA_DEV_NONE)) goto err_out; if (ap->flags & (ATA_FLAG_SATA_RESET | ATA_FLAG_SRST)) { @@ -3202,18 +3353,18 @@ void ata_bus_reset(struct ata_port *ap) err_out: ata_port_printk(ap, KERN_ERR, "disabling port\n"); - ap->ops->port_disable(ap); + ata_port_disable(ap); DPRINTK("EXIT\n"); } /** - * sata_phy_debounce - debounce SATA phy status - * @ap: ATA port to debounce SATA phy status for + * sata_link_debounce - debounce SATA phy status + * @link: ATA link to debounce SATA phy status for * @params: timing parameters { interval, duratinon, timeout } in msec * @deadline: deadline jiffies for the operation * - * Make sure SStatus of @ap reaches stable state, determined by +* Make sure SStatus of @link reaches stable state, determined by * holding the same value where DET is not 1 for @duration polled * every @interval, before @timeout. Timeout constraints the * beginning of the stable state. Because DET gets stuck at 1 on @@ -3229,8 +3380,8 @@ err_out: * RETURNS: * 0 on success, -errno on failure. */ -int sata_phy_debounce(struct ata_port *ap, const unsigned long *params, - unsigned long deadline) +int sata_link_debounce(struct ata_link *link, const unsigned long *params, + unsigned long deadline) { unsigned long interval_msec = params[0]; unsigned long duration = msecs_to_jiffies(params[1]); @@ -3242,7 +3393,7 @@ int sata_phy_debounce(struct ata_port *ap, const unsigned long *params, if (time_before(t, deadline)) deadline = t; - if ((rc = sata_scr_read(ap, SCR_STATUS, &cur))) + if ((rc = sata_scr_read(link, SCR_STATUS, &cur))) return rc; cur &= 0xf; @@ -3251,7 +3402,7 @@ int sata_phy_debounce(struct ata_port *ap, const unsigned long *params, while (1) { msleep(interval_msec); - if ((rc = sata_scr_read(ap, SCR_STATUS, &cur))) + if ((rc = sata_scr_read(link, SCR_STATUS, &cur))) return rc; cur &= 0xf; @@ -3277,12 +3428,12 @@ int sata_phy_debounce(struct ata_port *ap, const unsigned long *params, } /** - * sata_phy_resume - resume SATA phy - * @ap: ATA port to resume SATA phy for + * sata_link_resume - resume SATA link + * @link: ATA link to resume SATA * @params: timing parameters { interval, duratinon, timeout } in msec * @deadline: deadline jiffies for the operation * - * Resume SATA phy of @ap and debounce it. + * Resume SATA phy @link and debounce it. * * LOCKING: * Kernel thread context (may sleep) @@ -3290,18 +3441,18 @@ int sata_phy_debounce(struct ata_port *ap, const unsigned long *params, * RETURNS: * 0 on success, -errno on failure. */ -int sata_phy_resume(struct ata_port *ap, const unsigned long *params, - unsigned long deadline) +int sata_link_resume(struct ata_link *link, const unsigned long *params, + unsigned long deadline) { u32 scontrol; int rc; - if ((rc = sata_scr_read(ap, SCR_CONTROL, &scontrol))) + if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol))) return rc; scontrol = (scontrol & 0x0f0) | 0x300; - if ((rc = sata_scr_write(ap, SCR_CONTROL, scontrol))) + if ((rc = sata_scr_write(link, SCR_CONTROL, scontrol))) return rc; /* Some PHYs react badly if SStatus is pounded immediately @@ -3309,15 +3460,15 @@ int sata_phy_resume(struct ata_port *ap, const unsigned long *params, */ msleep(200); - return sata_phy_debounce(ap, params, deadline); + return sata_link_debounce(link, params, deadline); } /** * ata_std_prereset - prepare for reset - * @ap: ATA port to be reset + * @link: ATA link to be reset * @deadline: deadline jiffies for the operation * - * @ap is about to be reset. Initialize it. Failure from + * @link is about to be reset. Initialize it. Failure from * prereset makes libata abort whole reset sequence and give up * that port, so prereset should be best-effort. It does its * best to prepare for reset sequence but if things go wrong, it @@ -3329,37 +3480,44 @@ int sata_phy_resume(struct ata_port *ap, const unsigned long *params, * RETURNS: * 0 on success, -errno otherwise. */ -int ata_std_prereset(struct ata_port *ap, unsigned long deadline) +int ata_std_prereset(struct ata_link *link, unsigned long deadline) { - struct ata_eh_context *ehc = &ap->eh_context; + struct ata_port *ap = link->ap; + struct ata_eh_context *ehc = &link->eh_context; const unsigned long *timing = sata_ehc_deb_timing(ehc); int rc; /* handle link resume */ if ((ehc->i.flags & ATA_EHI_RESUME_LINK) && - (ap->flags & ATA_FLAG_HRST_TO_RESUME)) + (link->flags & ATA_LFLAG_HRST_TO_RESUME)) + ehc->i.action |= ATA_EH_HARDRESET; + + /* Some PMPs don't work with only SRST, force hardreset if PMP + * is supported. + */ + if (ap->flags & ATA_FLAG_PMP) ehc->i.action |= ATA_EH_HARDRESET; /* if we're about to do hardreset, nothing more to do */ if (ehc->i.action & ATA_EH_HARDRESET) return 0; - /* if SATA, resume phy */ + /* if SATA, resume link */ if (ap->flags & ATA_FLAG_SATA) { - rc = sata_phy_resume(ap, timing, deadline); + rc = sata_link_resume(link, timing, deadline); /* whine about phy resume failure but proceed */ if (rc && rc != -EOPNOTSUPP) - ata_port_printk(ap, KERN_WARNING, "failed to resume " + ata_link_printk(link, KERN_WARNING, "failed to resume " "link for reset (errno=%d)\n", rc); } /* Wait for !BSY if the controller can wait for the first D2H * Reg FIS and we don't know that no device is attached. */ - if (!(ap->flags & ATA_FLAG_SKIP_D2H_BSY) && !ata_port_offline(ap)) { + if (!(link->flags & ATA_LFLAG_SKIP_D2H_BSY) && !ata_link_offline(link)) { rc = ata_wait_ready(ap, deadline); if (rc && rc != -ENODEV) { - ata_port_printk(ap, KERN_WARNING, "device not ready " + ata_link_printk(link, KERN_WARNING, "device not ready " "(errno=%d), forcing hardreset\n", rc); ehc->i.action |= ATA_EH_HARDRESET; } @@ -3370,7 +3528,7 @@ int ata_std_prereset(struct ata_port *ap, unsigned long deadline) /** * ata_std_softreset - reset host port via ATA SRST - * @ap: port to reset + * @link: ATA link to reset * @classes: resulting classes of attached devices * @deadline: deadline jiffies for the operation * @@ -3382,9 +3540,10 @@ int ata_std_prereset(struct ata_port *ap, unsigned long deadline) * RETURNS: * 0 on success, -errno otherwise. */ -int ata_std_softreset(struct ata_port *ap, unsigned int *classes, +int ata_std_softreset(struct ata_link *link, unsigned int *classes, unsigned long deadline) { + struct ata_port *ap = link->ap; unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS; unsigned int devmask = 0; int rc; @@ -3392,7 +3551,7 @@ int ata_std_softreset(struct ata_port *ap, unsigned int *classes, DPRINTK("ENTER\n"); - if (ata_port_offline(ap)) { + if (ata_link_offline(link)) { classes[0] = ATA_DEV_NONE; goto out; } @@ -3410,15 +3569,17 @@ int ata_std_softreset(struct ata_port *ap, unsigned int *classes, DPRINTK("about to softreset, devmask=%x\n", devmask); rc = ata_bus_softreset(ap, devmask, deadline); /* if link is occupied, -ENODEV too is an error */ - if (rc && (rc != -ENODEV || sata_scr_valid(ap))) { - ata_port_printk(ap, KERN_ERR, "SRST failed (errno=%d)\n", rc); + if (rc && (rc != -ENODEV || sata_scr_valid(link))) { + ata_link_printk(link, KERN_ERR, "SRST failed (errno=%d)\n", rc); return rc; } /* determine by signature whether we have ATA or ATAPI devices */ - classes[0] = ata_dev_try_classify(ap, 0, &err); + classes[0] = ata_dev_try_classify(&link->device[0], + devmask & (1 << 0), &err); if (slave_possible && err != 0x81) - classes[1] = ata_dev_try_classify(ap, 1, &err); + classes[1] = ata_dev_try_classify(&link->device[1], + devmask & (1 << 1), &err); out: DPRINTK("EXIT, classes[0]=%u [1]=%u\n", classes[0], classes[1]); @@ -3426,12 +3587,12 @@ int ata_std_softreset(struct ata_port *ap, unsigned int *classes, } /** - * sata_port_hardreset - reset port via SATA phy reset - * @ap: port to reset + * sata_link_hardreset - reset link via SATA phy reset + * @link: link to reset * @timing: timing parameters { interval, duratinon, timeout } in msec * @deadline: deadline jiffies for the operation * - * SATA phy-reset host port using DET bits of SControl register. + * SATA phy-reset @link using DET bits of SControl register. * * LOCKING: * Kernel thread context (may sleep) @@ -3439,7 +3600,7 @@ int ata_std_softreset(struct ata_port *ap, unsigned int *classes, * RETURNS: * 0 on success, -errno otherwise. */ -int sata_port_hardreset(struct ata_port *ap, const unsigned long *timing, +int sata_link_hardreset(struct ata_link *link, const unsigned long *timing, unsigned long deadline) { u32 scontrol; @@ -3447,30 +3608,30 @@ int sata_port_hardreset(struct ata_port *ap, const unsigned long *timing, DPRINTK("ENTER\n"); - if (sata_set_spd_needed(ap)) { + if (sata_set_spd_needed(link)) { /* SATA spec says nothing about how to reconfigure * spd. To be on the safe side, turn off phy during * reconfiguration. This works for at least ICH7 AHCI * and Sil3124. */ - if ((rc = sata_scr_read(ap, SCR_CONTROL, &scontrol))) + if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol))) goto out; scontrol = (scontrol & 0x0f0) | 0x304; - if ((rc = sata_scr_write(ap, SCR_CONTROL, scontrol))) + if ((rc = sata_scr_write(link, SCR_CONTROL, scontrol))) goto out; - sata_set_spd(ap); + sata_set_spd(link); } /* issue phy wake/reset */ - if ((rc = sata_scr_read(ap, SCR_CONTROL, &scontrol))) + if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol))) goto out; scontrol = (scontrol & 0x0f0) | 0x301; - if ((rc = sata_scr_write_flush(ap, SCR_CONTROL, scontrol))) + if ((rc = sata_scr_write_flush(link, SCR_CONTROL, scontrol))) goto out; /* Couldn't find anything in SATA I/II specs, but AHCI-1.1 @@ -3478,8 +3639,8 @@ int sata_port_hardreset(struct ata_port *ap, const unsigned long *timing, */ msleep(1); - /* bring phy back */ - rc = sata_phy_resume(ap, timing, deadline); + /* bring link back */ + rc = sata_link_resume(link, timing, deadline); out: DPRINTK("EXIT, rc=%d\n", rc); return rc; @@ -3487,7 +3648,7 @@ int sata_port_hardreset(struct ata_port *ap, const unsigned long *timing, /** * sata_std_hardreset - reset host port via SATA phy reset - * @ap: port to reset + * @link: link to reset * @class: resulting class of attached device * @deadline: deadline jiffies for the operation * @@ -3500,24 +3661,25 @@ int sata_port_hardreset(struct ata_port *ap, const unsigned long *timing, * RETURNS: * 0 on success, -errno otherwise. */ -int sata_std_hardreset(struct ata_port *ap, unsigned int *class, +int sata_std_hardreset(struct ata_link *link, unsigned int *class, unsigned long deadline) { - const unsigned long *timing = sata_ehc_deb_timing(&ap->eh_context); + struct ata_port *ap = link->ap; + const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context); int rc; DPRINTK("ENTER\n"); /* do hardreset */ - rc = sata_port_hardreset(ap, timing, deadline); + rc = sata_link_hardreset(link, timing, deadline); if (rc) { - ata_port_printk(ap, KERN_ERR, + ata_link_printk(link, KERN_ERR, "COMRESET failed (errno=%d)\n", rc); return rc; } /* TODO: phy layer with polling, timeouts, etc. */ - if (ata_port_offline(ap)) { + if (ata_link_offline(link)) { *class = ATA_DEV_NONE; DPRINTK("EXIT, link offline\n"); return 0; @@ -3526,17 +3688,27 @@ int sata_std_hardreset(struct ata_port *ap, unsigned int *class, /* wait a while before checking status, see SRST for more info */ msleep(150); + /* If PMP is supported, we have to do follow-up SRST. Note + * that some PMPs don't send D2H Reg FIS after hardreset at + * all if the first port is empty. Wait for it just for a + * second and request follow-up SRST. + */ + if (ap->flags & ATA_FLAG_PMP) { + ata_wait_ready(ap, jiffies + HZ); + return -EAGAIN; + } + rc = ata_wait_ready(ap, deadline); /* link occupied, -ENODEV too is an error */ if (rc) { - ata_port_printk(ap, KERN_ERR, + ata_link_printk(link, KERN_ERR, "COMRESET failed (errno=%d)\n", rc); return rc; } ap->ops->dev_select(ap, 0); /* probably unnecessary */ - *class = ata_dev_try_classify(ap, 0, NULL); + *class = ata_dev_try_classify(link->device, 1, NULL); DPRINTK("EXIT, class=%u\n", *class); return 0; @@ -3544,7 +3716,7 @@ int sata_std_hardreset(struct ata_port *ap, unsigned int *class, /** * ata_std_postreset - standard postreset callback - * @ap: the target ata_port + * @link: the target ata_link * @classes: classes of attached devices * * This function is invoked after a successful reset. Note that @@ -3554,18 +3726,19 @@ int sata_std_hardreset(struct ata_port *ap, unsigned int *class, * LOCKING: * Kernel thread context (may sleep) */ -void ata_std_postreset(struct ata_port *ap, unsigned int *classes) +void ata_std_postreset(struct ata_link *link, unsigned int *classes) { + struct ata_port *ap = link->ap; u32 serror; DPRINTK("ENTER\n"); /* print link status */ - sata_print_link_status(ap); + sata_print_link_status(link); /* clear SError */ - if (sata_scr_read(ap, SCR_ERROR, &serror) == 0) - sata_scr_write(ap, SCR_ERROR, serror); + if (sata_scr_read(link, SCR_ERROR, &serror) == 0) + sata_scr_write(link, SCR_ERROR, serror); /* is double-select really necessary? */ if (classes[0] != ATA_DEV_NONE) @@ -3652,7 +3825,7 @@ static int ata_dev_same_device(struct ata_device *dev, unsigned int new_class, int ata_dev_reread_id(struct ata_device *dev, unsigned int readid_flags) { unsigned int class = dev->class; - u16 *id = (void *)dev->ap->sector_buf; + u16 *id = (void *)dev->link->ap->sector_buf; int rc; /* read ID data */ @@ -3671,6 +3844,7 @@ int ata_dev_reread_id(struct ata_device *dev, unsigned int readid_flags) /** * ata_dev_revalidate - Revalidate ATA device * @dev: device to revalidate + * @new_class: new class code * @readid_flags: read ID flags * * Re-read IDENTIFY page, make sure @dev is still attached to the @@ -3682,7 +3856,8 @@ int ata_dev_reread_id(struct ata_device *dev, unsigned int readid_flags) * RETURNS: * 0 on success, negative errno otherwise */ -int ata_dev_revalidate(struct ata_device *dev, unsigned int readid_flags) +int ata_dev_revalidate(struct ata_device *dev, unsigned int new_class, + unsigned int readid_flags) { u64 n_sectors = dev->n_sectors; int rc; @@ -3690,6 +3865,15 @@ int ata_dev_revalidate(struct ata_device *dev, unsigned int readid_flags) if (!ata_dev_enabled(dev)) return -ENODEV; + /* fail early if !ATA && !ATAPI to avoid issuing [P]IDENTIFY to PMP */ + if (ata_class_enabled(new_class) && + new_class != ATA_DEV_ATA && new_class != ATA_DEV_ATAPI) { + ata_dev_printk(dev, KERN_INFO, "class mismatch %u != %u\n", + dev->class, new_class); + rc = -ENODEV; + goto fail; + } + /* re-read ID */ rc = ata_dev_reread_id(dev, readid_flags); if (rc) @@ -3763,6 +3947,9 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { { "IOMEGA ZIP 250 ATAPI", NULL, ATA_HORKAGE_NODMA }, /* temporary fix */ { "IOMEGA ZIP 250 ATAPI Floppy", NULL, ATA_HORKAGE_NODMA }, + /* Odd clown on sil3726/4726 PMPs */ + { "Config Disk", NULL, ATA_HORKAGE_NODMA | + ATA_HORKAGE_SKIP_PM }, /* Weird ATAPI devices */ { "TORiSAN DVD-ROM DRD-N216", NULL, ATA_HORKAGE_MAX_SEC_128 }, @@ -3775,16 +3962,12 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { /* http://thread.gmane.org/gmane.linux.ide/14907 */ { "FUJITSU MHT2060BH", NULL, ATA_HORKAGE_NONCQ }, /* NCQ is broken */ - { "Maxtor 6L250S0", "BANC1G10", ATA_HORKAGE_NONCQ }, - { "Maxtor 6B200M0", "BANC1BM0", ATA_HORKAGE_NONCQ }, - { "Maxtor 6B200M0", "BANC1B10", ATA_HORKAGE_NONCQ }, - { "Maxtor 7B250S0", "BANC1B70", ATA_HORKAGE_NONCQ, }, - { "Maxtor 7B300S0", "BANC1B70", ATA_HORKAGE_NONCQ }, + { "Maxtor *", "BANC*", ATA_HORKAGE_NONCQ }, { "Maxtor 7V300F0", "VA111630", ATA_HORKAGE_NONCQ }, - { "HITACHI HDS7250SASUN500G 0621KTAWSD", "K2AOAJ0AHITACHI", - ATA_HORKAGE_NONCQ }, - /* NCQ hard hangs device under heavier load, needs hard power cycle */ - { "Maxtor 6B250S0", "BANC1B70", ATA_HORKAGE_NONCQ }, + { "HITACHI HDS7250SASUN500G*", NULL, ATA_HORKAGE_NONCQ }, + { "HITACHI HDS7225SBSUN250G*", NULL, ATA_HORKAGE_NONCQ }, + { "ST380817AS", "3.42", ATA_HORKAGE_NONCQ }, + /* Blacklist entries taken from Silicon Image 3124/3132 Windows driver .inf file - also several Linux problem reports */ { "HTS541060G9SA00", "MB3OC60D", ATA_HORKAGE_NONCQ, }, @@ -3793,11 +3976,16 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { /* Drives which do spurious command completion */ { "HTS541680J9SA00", "SB2IC7EP", ATA_HORKAGE_NONCQ, }, { "HTS541612J9SA00", "SBDIC7JP", ATA_HORKAGE_NONCQ, }, + { "HDT722516DLA380", "V43OA96A", ATA_HORKAGE_NONCQ, }, { "Hitachi HTS541616J9SA00", "SB4OC70P", ATA_HORKAGE_NONCQ, }, { "WDC WD740ADFD-00NLR1", NULL, ATA_HORKAGE_NONCQ, }, + { "WDC WD3200AAJS-00RYA0", "12.01B01", ATA_HORKAGE_NONCQ, }, { "FUJITSU MHV2080BH", "00840028", ATA_HORKAGE_NONCQ, }, + { "ST9120822AS", "3.CLF", ATA_HORKAGE_NONCQ, }, { "ST9160821AS", "3.CLF", ATA_HORKAGE_NONCQ, }, - { "ST3160812AS", "3.AD", ATA_HORKAGE_NONCQ, }, + { "ST9160821AS", "3.ALD", ATA_HORKAGE_NONCQ, }, + { "ST3160812AS", "3.ADJ", ATA_HORKAGE_NONCQ, }, + { "ST980813AS", "3.ADB", ATA_HORKAGE_NONCQ, }, { "SAMSUNG HD401LJ", "ZZ100-15", ATA_HORKAGE_NONCQ, }, /* devices which puke on READ_NATIVE_MAX */ @@ -3806,10 +3994,31 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { { "WDC WD2500JD-00HBB0", "WD-WMAL71490727", ATA_HORKAGE_BROKEN_HPA }, { "MAXTOR 6L080L4", "A93.0500", ATA_HORKAGE_BROKEN_HPA }, + /* Devices which report 1 sector over size HPA */ + { "ST340823A", NULL, ATA_HORKAGE_HPA_SIZE, }, + { "ST320413A", NULL, ATA_HORKAGE_HPA_SIZE, }, + /* End Marker */ { } }; +int strn_pattern_cmp(const char *patt, const char *name, int wildchar) +{ + const char *p; + int len; + + /* + * check for trailing wildcard: *\0 + */ + p = strchr(patt, wildchar); + if (p && ((*(p + 1)) == 0)) + len = p - patt; + else + len = strlen(name); + + return strncmp(patt, name, len); +} + static unsigned long ata_dev_blacklisted(const struct ata_device *dev) { unsigned char model_num[ATA_ID_PROD_LEN + 1]; @@ -3820,10 +4029,10 @@ static unsigned long ata_dev_blacklisted(const struct ata_device *dev) ata_id_c_string(dev->id, model_rev, ATA_ID_FW_REV, sizeof(model_rev)); while (ad->model_num) { - if (!strcmp(ad->model_num, model_num)) { + if (!strn_pattern_cmp(ad->model_num, model_num, '*')) { if (ad->model_rev == NULL) return ad->horkage; - if (!strcmp(ad->model_rev, model_rev)) + if (!strn_pattern_cmp(ad->model_rev, model_rev, '*')) return ad->horkage; } ad++; @@ -3837,7 +4046,7 @@ static int ata_dma_blacklisted(const struct ata_device *dev) * DMA blacklist those ATAPI devices with CDB-intr (and use PIO) * if the LLDD handles only interrupts in the HSM_ST_LAST state. */ - if ((dev->ap->flags & ATA_FLAG_PIO_POLLING) && + if ((dev->link->ap->flags & ATA_FLAG_PIO_POLLING) && (dev->flags & ATA_DFLAG_CDB_INTR)) return 1; return (dev->horkage & ATA_HORKAGE_NODMA) ? 1 : 0; @@ -3857,7 +4066,8 @@ static int ata_dma_blacklisted(const struct ata_device *dev) */ static void ata_dev_xfermask(struct ata_device *dev) { - struct ata_port *ap = dev->ap; + struct ata_link *link = dev->link; + struct ata_port *ap = link->ap; struct ata_host *host = ap->host; unsigned long xfer_mask; @@ -3955,7 +4165,43 @@ static unsigned int ata_dev_set_xfermode(struct ata_device *dev) tf.protocol = ATA_PROT_NODATA; tf.nsect = dev->xfer_mode; - err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0); + err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0); + + DPRINTK("EXIT, err_mask=%x\n", err_mask); + return err_mask; +} + +/** + * ata_dev_set_AN - Issue SET FEATURES - SATA FEATURES + * @dev: Device to which command will be sent + * @enable: Whether to enable or disable the feature + * + * Issue SET FEATURES - SATA FEATURES command to device @dev + * on port @ap with sector count set to indicate Asynchronous + * Notification feature + * + * LOCKING: + * PCI/etc. bus probe sem. + * + * RETURNS: + * 0 on success, AC_ERR_* mask otherwise. + */ +static unsigned int ata_dev_set_AN(struct ata_device *dev, u8 enable) +{ + struct ata_taskfile tf; + unsigned int err_mask; + + /* set up set-features taskfile */ + DPRINTK("set features - SATA features\n"); + + ata_tf_init(dev, &tf); + tf.command = ATA_CMD_SET_FEATURES; + tf.feature = enable; + tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; + tf.protocol = ATA_PROT_NODATA; + tf.nsect = SATA_AN; + + err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0); DPRINTK("EXIT, err_mask=%x\n", err_mask); return err_mask; @@ -3993,7 +4239,7 @@ static unsigned int ata_dev_init_params(struct ata_device *dev, tf.nsect = sectors; tf.device |= (heads - 1) & 0x0f; /* max head = num. of heads - 1 */ - err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0); + err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0); /* A clean abort indicates an original or just out of spec drive and we should continue as we issue the setup based on the drive reported working geometry */ @@ -4207,6 +4453,36 @@ int ata_check_atapi_dma(struct ata_queued_cmd *qc) } /** + * ata_std_qc_defer - Check whether a qc needs to be deferred + * @qc: ATA command in question + * + * Non-NCQ commands cannot run with any other command, NCQ or + * not. As upper layer only knows the queue depth, we are + * responsible for maintaining exclusion. This function checks + * whether a new command @qc can be issued. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * ATA_DEFER_* if deferring is needed, 0 otherwise. + */ +int ata_std_qc_defer(struct ata_queued_cmd *qc) +{ + struct ata_link *link = qc->dev->link; + + if (qc->tf.protocol == ATA_PROT_NCQ) { + if (!ata_tag_valid(link->active_tag)) + return 0; + } else { + if (!ata_tag_valid(link->active_tag) && !link->sactive) + return 0; + } + + return ATA_DEFER_LINK; +} + +/** * ata_qc_prep - Prepare taskfile for submission * @qc: Metadata associated with taskfile to be prepared * @@ -4482,7 +4758,7 @@ void swap_buf_le16(u16 *buf, unsigned int buf_words) void ata_data_xfer(struct ata_device *adev, unsigned char *buf, unsigned int buflen, int write_data) { - struct ata_port *ap = adev->ap; + struct ata_port *ap = adev->link->ap; unsigned int words = buflen >> 1; /* Transfer multiple of 2 bytes */ @@ -4611,6 +4887,8 @@ static void ata_pio_sectors(struct ata_queued_cmd *qc) ata_pio_sector(qc); } else ata_pio_sector(qc); + + ata_altstatus(qc->ap); /* flush */ } /** @@ -4785,6 +5063,7 @@ static void atapi_pio_bytes(struct ata_queued_cmd *qc) VPRINTK("ata%u: xfering %d bytes\n", ap->print_id, bytes); __atapi_pio_bytes(qc, bytes); + ata_altstatus(ap); /* flush */ return; @@ -4956,7 +5235,6 @@ fsm_start: */ ap->hsm_task_state = HSM_ST; ata_pio_sectors(qc); - ata_altstatus(ap); /* flush */ } else /* send CDB */ atapi_send_cdb(ap, qc); @@ -5037,7 +5315,6 @@ fsm_start: if (!(qc->tf.flags & ATA_TFLAG_WRITE)) { ata_pio_sectors(qc); - ata_altstatus(ap); status = ata_wait_idle(ap); } @@ -5057,13 +5334,11 @@ fsm_start: if (ap->hsm_task_state == HSM_ST_LAST && (!(qc->tf.flags & ATA_TFLAG_WRITE))) { /* all data read */ - ata_altstatus(ap); status = ata_wait_idle(ap); goto fsm_start; } } - ata_altstatus(ap); /* flush */ poll_next = 1; break; @@ -5188,7 +5463,7 @@ static struct ata_queued_cmd *ata_qc_new(struct ata_port *ap) struct ata_queued_cmd *ata_qc_new_init(struct ata_device *dev) { - struct ata_port *ap = dev->ap; + struct ata_port *ap = dev->link->ap; struct ata_queued_cmd *qc; qc = ata_qc_new(ap); @@ -5231,6 +5506,7 @@ void ata_qc_free(struct ata_queued_cmd *qc) void __ata_qc_complete(struct ata_queued_cmd *qc) { struct ata_port *ap = qc->ap; + struct ata_link *link = qc->dev->link; WARN_ON(qc == NULL); /* ata_qc_from_tag _might_ return NULL */ WARN_ON(!(qc->flags & ATA_QCFLAG_ACTIVE)); @@ -5239,10 +5515,19 @@ void __ata_qc_complete(struct ata_queued_cmd *qc) ata_sg_clean(qc); /* command should be marked inactive atomically with qc completion */ - if (qc->tf.protocol == ATA_PROT_NCQ) - ap->sactive &= ~(1 << qc->tag); - else - ap->active_tag = ATA_TAG_POISON; + if (qc->tf.protocol == ATA_PROT_NCQ) { + link->sactive &= ~(1 << qc->tag); + if (!link->sactive) + ap->nr_active_links--; + } else { + link->active_tag = ATA_TAG_POISON; + ap->nr_active_links--; + } + + /* clear exclusive status */ + if (unlikely(qc->flags & ATA_QCFLAG_CLEAR_EXCL && + ap->excl_link == link)) + ap->excl_link = NULL; /* atapi: mark qc as inactive to prevent the interrupt handler * from completing the command twice later, before the error handler @@ -5411,19 +5696,25 @@ static inline int ata_should_dma_map(struct ata_queued_cmd *qc) void ata_qc_issue(struct ata_queued_cmd *qc) { struct ata_port *ap = qc->ap; + struct ata_link *link = qc->dev->link; /* Make sure only one non-NCQ command is outstanding. The * check is skipped for old EH because it reuses active qc to * request ATAPI sense. */ - WARN_ON(ap->ops->error_handler && ata_tag_valid(ap->active_tag)); + WARN_ON(ap->ops->error_handler && ata_tag_valid(link->active_tag)); if (qc->tf.protocol == ATA_PROT_NCQ) { - WARN_ON(ap->sactive & (1 << qc->tag)); - ap->sactive |= 1 << qc->tag; + WARN_ON(link->sactive & (1 << qc->tag)); + + if (!link->sactive) + ap->nr_active_links++; + link->sactive |= 1 << qc->tag; } else { - WARN_ON(ap->sactive); - ap->active_tag = qc->tag; + WARN_ON(link->sactive); + + ap->nr_active_links++; + link->active_tag = qc->tag; } qc->flags |= ATA_QCFLAG_ACTIVE; @@ -5606,7 +5897,7 @@ unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc) inline unsigned int ata_host_intr (struct ata_port *ap, struct ata_queued_cmd *qc) { - struct ata_eh_info *ehi = &ap->eh_info; + struct ata_eh_info *ehi = &ap->link.eh_info; u8 status, host_stat = 0; VPRINTK("ata%u: protocol %d task_state %d\n", @@ -5680,7 +5971,8 @@ idle_irq: #ifdef ATA_IRQ_TRAP if ((ap->stats.idle_irq % 1000) == 0) { - ap->ops->irq_ack(ap, 0); /* debug trap */ + ata_chk_status(ap); + ap->ops->irq_clear(ap); ata_port_printk(ap, KERN_WARNING, "irq trap\n"); return 1; } @@ -5721,7 +6013,7 @@ irqreturn_t ata_interrupt (int irq, void *dev_instance) !(ap->flags & ATA_FLAG_DISABLED)) { struct ata_queued_cmd *qc; - qc = ata_qc_from_tag(ap, ap->active_tag); + qc = ata_qc_from_tag(ap, ap->link.active_tag); if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING)) && (qc->flags & ATA_QCFLAG_ACTIVE)) handled |= ata_host_intr(ap, qc); @@ -5735,9 +6027,9 @@ irqreturn_t ata_interrupt (int irq, void *dev_instance) /** * sata_scr_valid - test whether SCRs are accessible - * @ap: ATA port to test SCR accessibility for + * @link: ATA link to test SCR accessibility for * - * Test whether SCRs are accessible for @ap. + * Test whether SCRs are accessible for @link. * * LOCKING: * None. @@ -5745,60 +6037,74 @@ irqreturn_t ata_interrupt (int irq, void *dev_instance) * RETURNS: * 1 if SCRs are accessible, 0 otherwise. */ -int sata_scr_valid(struct ata_port *ap) +int sata_scr_valid(struct ata_link *link) { + struct ata_port *ap = link->ap; + return (ap->flags & ATA_FLAG_SATA) && ap->ops->scr_read; } /** * sata_scr_read - read SCR register of the specified port - * @ap: ATA port to read SCR for + * @link: ATA link to read SCR for * @reg: SCR to read * @val: Place to store read value * - * Read SCR register @reg of @ap into *@val. This function is - * guaranteed to succeed if the cable type of the port is SATA - * and the port implements ->scr_read. + * Read SCR register @reg of @link into *@val. This function is + * guaranteed to succeed if @link is ap->link, the cable type of + * the port is SATA and the port implements ->scr_read. * * LOCKING: - * None. + * None if @link is ap->link. Kernel thread context otherwise. * * RETURNS: * 0 on success, negative errno on failure. */ -int sata_scr_read(struct ata_port *ap, int reg, u32 *val) +int sata_scr_read(struct ata_link *link, int reg, u32 *val) { - if (sata_scr_valid(ap)) - return ap->ops->scr_read(ap, reg, val); - return -EOPNOTSUPP; + if (ata_is_host_link(link)) { + struct ata_port *ap = link->ap; + + if (sata_scr_valid(link)) + return ap->ops->scr_read(ap, reg, val); + return -EOPNOTSUPP; + } + + return sata_pmp_scr_read(link, reg, val); } /** * sata_scr_write - write SCR register of the specified port - * @ap: ATA port to write SCR for + * @link: ATA link to write SCR for * @reg: SCR to write * @val: value to write * - * Write @val to SCR register @reg of @ap. This function is - * guaranteed to succeed if the cable type of the port is SATA - * and the port implements ->scr_read. + * Write @val to SCR register @reg of @link. This function is + * guaranteed to succeed if @link is ap->link, the cable type of + * the port is SATA and the port implements ->scr_read. * * LOCKING: - * None. + * None if @link is ap->link. Kernel thread context otherwise. * * RETURNS: * 0 on success, negative errno on failure. */ -int sata_scr_write(struct ata_port *ap, int reg, u32 val) +int sata_scr_write(struct ata_link *link, int reg, u32 val) { - if (sata_scr_valid(ap)) - return ap->ops->scr_write(ap, reg, val); - return -EOPNOTSUPP; + if (ata_is_host_link(link)) { + struct ata_port *ap = link->ap; + + if (sata_scr_valid(link)) + return ap->ops->scr_write(ap, reg, val); + return -EOPNOTSUPP; + } + + return sata_pmp_scr_write(link, reg, val); } /** * sata_scr_write_flush - write SCR register of the specified port and flush - * @ap: ATA port to write SCR for + * @link: ATA link to write SCR for * @reg: SCR to write * @val: value to write * @@ -5806,31 +6112,36 @@ int sata_scr_write(struct ata_port *ap, int reg, u32 val) * function performs flush after writing to the register. * * LOCKING: - * None. + * None if @link is ap->link. Kernel thread context otherwise. * * RETURNS: * 0 on success, negative errno on failure. */ -int sata_scr_write_flush(struct ata_port *ap, int reg, u32 val) +int sata_scr_write_flush(struct ata_link *link, int reg, u32 val) { - int rc; + if (ata_is_host_link(link)) { + struct ata_port *ap = link->ap; + int rc; - if (sata_scr_valid(ap)) { - rc = ap->ops->scr_write(ap, reg, val); - if (rc == 0) - rc = ap->ops->scr_read(ap, reg, &val); - return rc; + if (sata_scr_valid(link)) { + rc = ap->ops->scr_write(ap, reg, val); + if (rc == 0) + rc = ap->ops->scr_read(ap, reg, &val); + return rc; + } + return -EOPNOTSUPP; } - return -EOPNOTSUPP; + + return sata_pmp_scr_write(link, reg, val); } /** - * ata_port_online - test whether the given port is online - * @ap: ATA port to test + * ata_link_online - test whether the given link is online + * @link: ATA link to test * - * Test whether @ap is online. Note that this function returns 0 - * if online status of @ap cannot be obtained, so - * ata_port_online(ap) != !ata_port_offline(ap). + * Test whether @link is online. Note that this function returns + * 0 if online status of @link cannot be obtained, so + * ata_link_online(link) != !ata_link_offline(link). * * LOCKING: * None. @@ -5838,22 +6149,23 @@ int sata_scr_write_flush(struct ata_port *ap, int reg, u32 val) * RETURNS: * 1 if the port online status is available and online. */ -int ata_port_online(struct ata_port *ap) +int ata_link_online(struct ata_link *link) { u32 sstatus; - if (!sata_scr_read(ap, SCR_STATUS, &sstatus) && (sstatus & 0xf) == 0x3) + if (sata_scr_read(link, SCR_STATUS, &sstatus) == 0 && + (sstatus & 0xf) == 0x3) return 1; return 0; } /** - * ata_port_offline - test whether the given port is offline - * @ap: ATA port to test + * ata_link_offline - test whether the given link is offline + * @link: ATA link to test * - * Test whether @ap is offline. Note that this function returns - * 0 if offline status of @ap cannot be obtained, so - * ata_port_online(ap) != !ata_port_offline(ap). + * Test whether @link is offline. Note that this function + * returns 0 if offline status of @link cannot be obtained, so + * ata_link_online(link) != !ata_link_offline(link). * * LOCKING: * None. @@ -5861,11 +6173,12 @@ int ata_port_online(struct ata_port *ap) * RETURNS: * 1 if the port offline status is available and offline. */ -int ata_port_offline(struct ata_port *ap) +int ata_link_offline(struct ata_link *link) { u32 sstatus; - if (!sata_scr_read(ap, SCR_STATUS, &sstatus) && (sstatus & 0xf) != 0x3) + if (sata_scr_read(link, SCR_STATUS, &sstatus) == 0 && + (sstatus & 0xf) != 0x3) return 1; return 0; } @@ -5883,6 +6196,10 @@ int ata_flush_cache(struct ata_device *dev) else cmd = ATA_CMD_FLUSH; + /* This is wrong. On a failed flush we get back the LBA of the lost + sector and we should (assuming it wasn't aborted as unknown) issue + a further flush command to continue the writeback until it + does not error */ err_mask = ata_do_simple_cmd(dev, cmd); if (err_mask) { ata_dev_printk(dev, KERN_ERR, "failed to flush cache\n"); @@ -5902,6 +6219,7 @@ static int ata_host_request_pm(struct ata_host *host, pm_message_t mesg, for (i = 0; i < host->n_ports; i++) { struct ata_port *ap = host->ports[i]; + struct ata_link *link; /* Previous resume operation might still be in * progress. Wait for PM_PENDING to clear. @@ -5921,8 +6239,10 @@ static int ata_host_request_pm(struct ata_host *host, pm_message_t mesg, } ap->pflags |= ATA_PFLAG_PM_PENDING; - ap->eh_info.action |= action; - ap->eh_info.flags |= ehi_flags; + __ata_port_for_each_link(link, ap) { + link->eh_info.action |= action; + link->eh_info.flags |= ehi_flags; + } ata_port_schedule_eh(ap); @@ -6026,12 +6346,13 @@ int ata_port_start(struct ata_port *ap) */ void ata_dev_init(struct ata_device *dev) { - struct ata_port *ap = dev->ap; + struct ata_link *link = dev->link; + struct ata_port *ap = link->ap; unsigned long flags; /* SATA spd limit is bound to the first device */ - ap->sata_spd_limit = ap->hw_sata_spd_limit; - ap->sata_spd = 0; + link->sata_spd_limit = link->hw_sata_spd_limit; + link->sata_spd = 0; /* High bits of dev->flags are used to record warm plug * requests which occur asynchronously. Synchronize using @@ -6050,6 +6371,70 @@ void ata_dev_init(struct ata_device *dev) } /** + * ata_link_init - Initialize an ata_link structure + * @ap: ATA port link is attached to + * @link: Link structure to initialize + * @pmp: Port multiplier port number + * + * Initialize @link. + * + * LOCKING: + * Kernel thread context (may sleep) + */ +void ata_link_init(struct ata_port *ap, struct ata_link *link, int pmp) +{ + int i; + + /* clear everything except for devices */ + memset(link, 0, offsetof(struct ata_link, device[0])); + + link->ap = ap; + link->pmp = pmp; + link->active_tag = ATA_TAG_POISON; + link->hw_sata_spd_limit = UINT_MAX; + + /* can't use iterator, ap isn't initialized yet */ + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &link->device[i]; + + dev->link = link; + dev->devno = dev - link->device; + ata_dev_init(dev); + } +} + +/** + * sata_link_init_spd - Initialize link->sata_spd_limit + * @link: Link to configure sata_spd_limit for + * + * Initialize @link->[hw_]sata_spd_limit to the currently + * configured value. + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * 0 on success, -errno on failure. + */ +int sata_link_init_spd(struct ata_link *link) +{ + u32 scontrol, spd; + int rc; + + rc = sata_scr_read(link, SCR_CONTROL, &scontrol); + if (rc) + return rc; + + spd = (scontrol >> 4) & 0xf; + if (spd) + link->hw_sata_spd_limit &= (1 << spd) - 1; + + link->sata_spd_limit = link->hw_sata_spd_limit; + + return 0; +} + +/** * ata_port_alloc - allocate and initialize basic ATA port resources * @host: ATA host this allocated port belongs to * @@ -6064,7 +6449,6 @@ void ata_dev_init(struct ata_device *dev) struct ata_port *ata_port_alloc(struct ata_host *host) { struct ata_port *ap; - unsigned int i; DPRINTK("ENTER\n"); @@ -6079,9 +6463,6 @@ struct ata_port *ata_port_alloc(struct ata_host *host) ap->ctl = ATA_DEVCTL_OBS; ap->host = host; ap->dev = host->dev; - - ap->hw_sata_spd_limit = UINT_MAX; - ap->active_tag = ATA_TAG_POISON; ap->last_ctl = 0xFF; #if defined(ATA_VERBOSE_DEBUG) @@ -6104,12 +6485,7 @@ struct ata_port *ata_port_alloc(struct ata_host *host) ap->cbl = ATA_CBL_NONE; - for (i = 0; i < ATA_MAX_DEVICES; i++) { - struct ata_device *dev = &ap->device[i]; - dev->ap = ap; - dev->devno = i; - ata_dev_init(dev); - } + ata_link_init(ap, &ap->link, 0); #ifdef ATA_IRQ_TRAP ap->stats.unhandled_irq = 1; @@ -6145,6 +6521,7 @@ static void ata_host_release(struct device *gendev, void *res) if (ap->scsi_host) scsi_host_put(ap->scsi_host); + kfree(ap->pmp_link); kfree(ap); host->ports[i] = NULL; } @@ -6255,6 +6632,7 @@ struct ata_host *ata_host_alloc_pinfo(struct device *dev, ap->mwdma_mask = pi->mwdma_mask; ap->udma_mask = pi->udma_mask; ap->flags |= pi->flags; + ap->link.flags |= pi->link_flags; ap->ops = pi->port_ops; if (!host->ops && (pi->port_ops != &ata_dummy_port_ops)) @@ -6390,8 +6768,6 @@ int ata_host_register(struct ata_host *host, struct scsi_host_template *sht) /* set cable, sata_spd_limit and report */ for (i = 0; i < host->n_ports; i++) { struct ata_port *ap = host->ports[i]; - int irq_line; - u32 scontrol; unsigned long xfer_mask; /* set SATA cable type if still unset */ @@ -6399,32 +6775,20 @@ int ata_host_register(struct ata_host *host, struct scsi_host_template *sht) ap->cbl = ATA_CBL_SATA; /* init sata_spd_limit to the current value */ - if (sata_scr_read(ap, SCR_CONTROL, &scontrol) == 0) { - int spd = (scontrol >> 4) & 0xf; - if (spd) - ap->hw_sata_spd_limit &= (1 << spd) - 1; - } - ap->sata_spd_limit = ap->hw_sata_spd_limit; - - /* report the secondary IRQ for second channel legacy */ - irq_line = host->irq; - if (i == 1 && host->irq2) - irq_line = host->irq2; + sata_link_init_spd(&ap->link); + /* print per-port info to dmesg */ xfer_mask = ata_pack_xfermask(ap->pio_mask, ap->mwdma_mask, ap->udma_mask); - /* print per-port info to dmesg */ - if (!ata_port_is_dummy(ap)) - ata_port_printk(ap, KERN_INFO, "%cATA max %s cmd 0x%p " - "ctl 0x%p bmdma 0x%p irq %d\n", + if (!ata_port_is_dummy(ap)) { + ata_port_printk(ap, KERN_INFO, + "%cATA max %s %s\n", (ap->flags & ATA_FLAG_SATA) ? 'S' : 'P', ata_mode_string(xfer_mask), - ap->ioaddr.cmd_addr, - ap->ioaddr.ctl_addr, - ap->ioaddr.bmdma_addr, - irq_line); - else + ap->link.eh_info.desc); + ata_ehi_clear_desc(&ap->link.eh_info); + } else ata_port_printk(ap, KERN_INFO, "DUMMY\n"); } @@ -6436,7 +6800,7 @@ int ata_host_register(struct ata_host *host, struct scsi_host_template *sht) /* probe */ if (ap->ops->error_handler) { - struct ata_eh_info *ehi = &ap->eh_info; + struct ata_eh_info *ehi = &ap->link.eh_info; unsigned long flags; ata_port_probe(ap); @@ -6444,7 +6808,8 @@ int ata_host_register(struct ata_host *host, struct scsi_host_template *sht) /* kick EH for boot probing */ spin_lock_irqsave(ap->lock, flags); - ehi->probe_mask = (1 << ATA_MAX_DEVICES) - 1; + ehi->probe_mask = + (1 << ata_link_max_devices(&ap->link)) - 1; ehi->action |= ATA_EH_SOFTRESET; ehi->flags |= ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET; @@ -6506,7 +6871,7 @@ int ata_host_activate(struct ata_host *host, int irq, irq_handler_t irq_handler, unsigned long irq_flags, struct scsi_host_template *sht) { - int rc; + int i, rc; rc = ata_host_start(host); if (rc) @@ -6517,8 +6882,8 @@ int ata_host_activate(struct ata_host *host, int irq, if (rc) return rc; - /* Used to print device info at probe */ - host->irq = irq; + for (i = 0; i < host->n_ports; i++) + ata_port_desc(host->ports[i], "irq %d", irq); rc = ata_host_register(host, sht); /* if failed, just free the IRQ and leave ports alone */ @@ -6542,7 +6907,8 @@ int ata_host_activate(struct ata_host *host, int irq, void ata_port_detach(struct ata_port *ap) { unsigned long flags; - int i; + struct ata_link *link; + struct ata_device *dev; if (!ap->ops->error_handler) goto skip_eh; @@ -6559,8 +6925,10 @@ void ata_port_detach(struct ata_port *ap) */ spin_lock_irqsave(ap->lock, flags); - for (i = 0; i < ATA_MAX_DEVICES; i++) - ata_dev_disable(&ap->device[i]); + ata_port_for_each_link(link, ap) { + ata_link_for_each_dev(dev, link) + ata_dev_disable(dev); + } spin_unlock_irqrestore(ap->lock, flags); @@ -6639,7 +7007,7 @@ void ata_std_ports(struct ata_ioports *ioaddr) */ void ata_pci_remove_one(struct pci_dev *pdev) { - struct device *dev = pci_dev_to_dev(pdev); + struct device *dev = &pdev->dev; struct ata_host *host = dev_get_drvdata(dev); ata_host_detach(host); @@ -6847,7 +7215,6 @@ static unsigned int ata_dummy_qc_issue(struct ata_queued_cmd *qc) } const struct ata_port_operations ata_dummy_port_ops = { - .port_disable = ata_port_disable, .check_status = ata_dummy_check_status, .check_altstatus = ata_dummy_check_status, .dev_select = ata_noop_dev_select, @@ -6909,6 +7276,7 @@ EXPORT_SYMBOL_GPL(ata_interrupt); EXPORT_SYMBOL_GPL(ata_do_set_mode); EXPORT_SYMBOL_GPL(ata_data_xfer); EXPORT_SYMBOL_GPL(ata_data_xfer_noirq); +EXPORT_SYMBOL_GPL(ata_std_qc_defer); EXPORT_SYMBOL_GPL(ata_qc_prep); EXPORT_SYMBOL_GPL(ata_dumb_qc_prep); EXPORT_SYMBOL_GPL(ata_noop_qc_prep); @@ -6925,14 +7293,14 @@ EXPORT_SYMBOL_GPL(ata_bmdma_post_internal_cmd); EXPORT_SYMBOL_GPL(ata_port_probe); EXPORT_SYMBOL_GPL(ata_dev_disable); EXPORT_SYMBOL_GPL(sata_set_spd); -EXPORT_SYMBOL_GPL(sata_phy_debounce); -EXPORT_SYMBOL_GPL(sata_phy_resume); +EXPORT_SYMBOL_GPL(sata_link_debounce); +EXPORT_SYMBOL_GPL(sata_link_resume); EXPORT_SYMBOL_GPL(sata_phy_reset); EXPORT_SYMBOL_GPL(__sata_phy_reset); EXPORT_SYMBOL_GPL(ata_bus_reset); EXPORT_SYMBOL_GPL(ata_std_prereset); EXPORT_SYMBOL_GPL(ata_std_softreset); -EXPORT_SYMBOL_GPL(sata_port_hardreset); +EXPORT_SYMBOL_GPL(sata_link_hardreset); EXPORT_SYMBOL_GPL(sata_std_hardreset); EXPORT_SYMBOL_GPL(ata_std_postreset); EXPORT_SYMBOL_GPL(ata_dev_classify); @@ -6953,8 +7321,8 @@ EXPORT_SYMBOL_GPL(sata_scr_valid); EXPORT_SYMBOL_GPL(sata_scr_read); EXPORT_SYMBOL_GPL(sata_scr_write); EXPORT_SYMBOL_GPL(sata_scr_write_flush); -EXPORT_SYMBOL_GPL(ata_port_online); -EXPORT_SYMBOL_GPL(ata_port_offline); +EXPORT_SYMBOL_GPL(ata_link_online); +EXPORT_SYMBOL_GPL(ata_link_offline); #ifdef CONFIG_PM EXPORT_SYMBOL_GPL(ata_host_suspend); EXPORT_SYMBOL_GPL(ata_host_resume); @@ -6985,22 +7353,31 @@ EXPORT_SYMBOL_GPL(ata_pci_default_filter); EXPORT_SYMBOL_GPL(ata_pci_clear_simplex); #endif /* CONFIG_PCI */ +EXPORT_SYMBOL_GPL(sata_pmp_qc_defer_cmd_switch); +EXPORT_SYMBOL_GPL(sata_pmp_std_prereset); +EXPORT_SYMBOL_GPL(sata_pmp_std_hardreset); +EXPORT_SYMBOL_GPL(sata_pmp_std_postreset); +EXPORT_SYMBOL_GPL(sata_pmp_do_eh); + EXPORT_SYMBOL_GPL(__ata_ehi_push_desc); EXPORT_SYMBOL_GPL(ata_ehi_push_desc); EXPORT_SYMBOL_GPL(ata_ehi_clear_desc); +EXPORT_SYMBOL_GPL(ata_port_desc); +#ifdef CONFIG_PCI +EXPORT_SYMBOL_GPL(ata_port_pbar_desc); +#endif /* CONFIG_PCI */ EXPORT_SYMBOL_GPL(ata_eng_timeout); EXPORT_SYMBOL_GPL(ata_port_schedule_eh); +EXPORT_SYMBOL_GPL(ata_link_abort); EXPORT_SYMBOL_GPL(ata_port_abort); EXPORT_SYMBOL_GPL(ata_port_freeze); +EXPORT_SYMBOL_GPL(sata_async_notification); EXPORT_SYMBOL_GPL(ata_eh_freeze_port); EXPORT_SYMBOL_GPL(ata_eh_thaw_port); EXPORT_SYMBOL_GPL(ata_eh_qc_complete); EXPORT_SYMBOL_GPL(ata_eh_qc_retry); EXPORT_SYMBOL_GPL(ata_do_eh); EXPORT_SYMBOL_GPL(ata_irq_on); -EXPORT_SYMBOL_GPL(ata_dummy_irq_on); -EXPORT_SYMBOL_GPL(ata_irq_ack); -EXPORT_SYMBOL_GPL(ata_dummy_irq_ack); EXPORT_SYMBOL_GPL(ata_dev_try_classify); EXPORT_SYMBOL_GPL(ata_cable_40wire); |