4 files changed, 10 insertions, 10 deletions
diff --git a/arch/mips/au1000/mtx-1/board_setup.c b/arch/mips/au1000/mtx-1/board_setup.c
index 7bc5af8917da..2c460c116570 100644
--- a/arch/mips/au1000/mtx-1/board_setup.c
+++ b/arch/mips/au1000/mtx-1/board_setup.c
@@ -54,11 +54,11 @@ void board_reset (void)
 
 void __init board_setup(void)
 {
-#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
 	// enable USB power switch
 	au_writel( au_readl(GPIO2_DIR) | 0x10, GPIO2_DIR );
 	au_writel( 0x100000, GPIO2_OUTPUT );
-#endif // defined (CONFIG_USB_OHCI)
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
 
 #ifdef CONFIG_PCI
 #if defined(__MIPSEB__)
diff --git a/arch/mips/au1000/pb1000/board_setup.c b/arch/mips/au1000/pb1000/board_setup.c
index 824cfafaff92..0aed89114bfc 100644
--- a/arch/mips/au1000/pb1000/board_setup.c
+++ b/arch/mips/au1000/pb1000/board_setup.c
@@ -54,7 +54,7 @@ void __init board_setup(void)
 	au_writel(0, SYS_PINSTATERD);
 	udelay(100);
 
-#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
 	/* zero and disable FREQ2 */
 	sys_freqctrl = au_readl(SYS_FREQCTRL0);
 	sys_freqctrl &= ~0xFFF00000;
@@ -102,7 +102,7 @@ void __init board_setup(void)
 	/*
 	 * Route 48MHz FREQ2 into USB Host and/or Device
 	 */
-#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
 	sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
 #endif
 	au_writel(sys_clksrc, SYS_CLKSRC);
@@ -116,7 +116,7 @@ void __init board_setup(void)
 	au_writel(pin_func, SYS_PINFUNC);
 	au_writel(0x2800, SYS_TRIOUTCLR);
 	au_writel(0x0030, SYS_OUTPUTCLR);
-#endif // defined (CONFIG_USB_OHCI)
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
 
 	// make gpio 15 an input (for interrupt line)
 	pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x100);
diff --git a/arch/mips/au1000/pb1100/board_setup.c b/arch/mips/au1000/pb1100/board_setup.c
index 6bc1f8e1b608..259ca05860c3 100644
--- a/arch/mips/au1000/pb1100/board_setup.c
+++ b/arch/mips/au1000/pb1100/board_setup.c
@@ -54,7 +54,7 @@ void __init board_setup(void)
 	au_writel(0, SYS_PININPUTEN);
 	udelay(100);
 
-#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
 	{
 		u32 pin_func, sys_freqctrl, sys_clksrc;
 
@@ -98,7 +98,7 @@ void __init board_setup(void)
 		pin_func |= 0x8000;
 		au_writel(pin_func, SYS_PINFUNC);
 	}
-#endif // defined (CONFIG_USB_OHCI)
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
 
 	/* Enable sys bus clock divider when IDLE state or no bus activity. */
 	au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
diff --git a/arch/mips/au1000/pb1500/board_setup.c b/arch/mips/au1000/pb1500/board_setup.c
index c9b655616fb3..a2d850db8902 100644
--- a/arch/mips/au1000/pb1500/board_setup.c
+++ b/arch/mips/au1000/pb1500/board_setup.c
@@ -56,7 +56,7 @@ void __init board_setup(void)
 	au_writel(0, SYS_PINSTATERD);
 	udelay(100);
 
-#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
 
 	/* GPIO201 is input for PCMCIA card detect */
 	/* GPIO203 is input for PCMCIA interrupt request */
@@ -85,7 +85,7 @@ void __init board_setup(void)
 	/*
 	 * Route 48MHz FREQ2 into USB Host and/or Device
 	 */
-#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
 	sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
 #endif
 	au_writel(sys_clksrc, SYS_CLKSRC);
@@ -95,7 +95,7 @@ void __init board_setup(void)
 	// 2nd USB port is USB host
 	pin_func |= 0x8000;
 	au_writel(pin_func, SYS_PINFUNC);
-#endif // defined (CONFIG_USB_OHCI)
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */