diff options
Diffstat (limited to 'arch/powerpc/platforms/embedded6xx')
| -rw-r--r-- | arch/powerpc/platforms/embedded6xx/Kconfig | 30 | ||||
| -rw-r--r-- | arch/powerpc/platforms/embedded6xx/Makefile | 1 | ||||
| -rw-r--r-- | arch/powerpc/platforms/embedded6xx/linkstation.c | 211 | ||||
| -rw-r--r-- | arch/powerpc/platforms/embedded6xx/ls_uart.c | 131 | ||||
| -rw-r--r-- | arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c | 94 |
5 files changed, 381 insertions, 86 deletions
diff --git a/arch/powerpc/platforms/embedded6xx/Kconfig b/arch/powerpc/platforms/embedded6xx/Kconfig index 234a861870a8..ddbe398fbd48 100644 --- a/arch/powerpc/platforms/embedded6xx/Kconfig +++ b/arch/powerpc/platforms/embedded6xx/Kconfig @@ -74,6 +74,18 @@ config SANDPOINT Select SANDPOINT if configuring for a Motorola Sandpoint X3 (any flavor). +config LINKSTATION + bool "Linkstation / Kurobox(HG) from Buffalo" + select MPIC + select FSL_SOC + select PPC_UDBG_16550 if SERIAL_8250 + help + Select LINKSTATION if configuring for one of PPC- (MPC8241) + based NAS systems from Buffalo Technology. So far only + KuroboxHG has been tested. In the future classical Kurobox, + Linkstation-I HD-HLAN and HD-HGLAN versions, and PPC-based + Terastation systems should be supported too. + config MPC7448HPC2 bool "Freescale MPC7448HPC2(Taiga)" select TSI108_BRIDGE @@ -146,15 +158,6 @@ config PQ2FADS Select PQ2FADS if you wish to configure for a Freescale PQ2FADS board (-VR or -ZU). -config LITE5200 - bool "Freescale LITE5200 / (IceCube)" - select PPC_MPC52xx - help - Support for the LITE5200 dev board for the MPC5200 from Freescale. - This is for the LITE5200 version 2.0 board. Don't know if it changes - much but it's only been tested on this board version. I think this - board is also known as IceCube. - config EV64360 bool "Marvell-EV64360BP" help @@ -172,9 +175,6 @@ config TQM8xxL depends on 8xx && (TQM823L || TQM850L || FPS850L || TQM855L || TQM860L) default y -config PPC_MPC52xx - bool - config 8260 bool "CPM2 Support" if WILLOW depends on 6xx @@ -208,7 +208,7 @@ config PPC_GEN550 depends on SANDPOINT || SPRUCE || PPLUS || \ PRPMC750 || PRPMC800 || LOPEC || \ (EV64260 && !SERIAL_MPSC) || CHESTNUT || RADSTONE_PPC7D || \ - 83xx + 83xx || LINKSTATION default y config FORCE @@ -282,13 +282,13 @@ config EPIC_SERIAL_MODE config MPC10X_BRIDGE bool - depends on POWERPMC250 || LOPEC || SANDPOINT + depends on POWERPMC250 || LOPEC || SANDPOINT || LINKSTATION select PPC_INDIRECT_PCI default y config MPC10X_OPENPIC bool - depends on POWERPMC250 || LOPEC || SANDPOINT + depends on POWERPMC250 || LOPEC || SANDPOINT || LINKSTATION default y config MPC10X_STORE_GATHERING diff --git a/arch/powerpc/platforms/embedded6xx/Makefile b/arch/powerpc/platforms/embedded6xx/Makefile index fa499fe59291..d3d11a3cd656 100644 --- a/arch/powerpc/platforms/embedded6xx/Makefile +++ b/arch/powerpc/platforms/embedded6xx/Makefile @@ -2,3 +2,4 @@ # Makefile for the 6xx/7xx/7xxxx linux kernel. # obj-$(CONFIG_MPC7448HPC2) += mpc7448_hpc2.o +obj-$(CONFIG_LINKSTATION) += linkstation.o ls_uart.o diff --git a/arch/powerpc/platforms/embedded6xx/linkstation.c b/arch/powerpc/platforms/embedded6xx/linkstation.c new file mode 100644 index 000000000000..61599d919ea8 --- /dev/null +++ b/arch/powerpc/platforms/embedded6xx/linkstation.c @@ -0,0 +1,211 @@ +/* + * Board setup routines for the Buffalo Linkstation / Kurobox Platform. + * + * Copyright (C) 2006 G. Liakhovetski (g.liakhovetski@gmx.de) + * + * Based on sandpoint.c by Mark A. Greer + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of + * any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/pci.h> +#include <linux/initrd.h> +#include <linux/root_dev.h> +#include <linux/mtd/physmap.h> + +#include <asm/time.h> +#include <asm/prom.h> +#include <asm/mpic.h> +#include <asm/mpc10x.h> +#include <asm/pci-bridge.h> + +static struct mtd_partition linkstation_physmap_partitions[] = { + { + .name = "mtd_firmimg", + .offset = 0x000000, + .size = 0x300000, + }, + { + .name = "mtd_bootcode", + .offset = 0x300000, + .size = 0x070000, + }, + { + .name = "mtd_status", + .offset = 0x370000, + .size = 0x010000, + }, + { + .name = "mtd_conf", + .offset = 0x380000, + .size = 0x080000, + }, + { + .name = "mtd_allflash", + .offset = 0x000000, + .size = 0x400000, + }, + { + .name = "mtd_data", + .offset = 0x310000, + .size = 0x0f0000, + }, +}; + +static int __init add_bridge(struct device_node *dev) +{ + int len; + struct pci_controller *hose; + int *bus_range; + + printk("Adding PCI host bridge %s\n", dev->full_name); + + bus_range = (int *) get_property(dev, "bus-range", &len); + if (bus_range == NULL || len < 2 * sizeof(int)) + printk(KERN_WARNING "Can't get bus-range for %s, assume" + " bus 0\n", dev->full_name); + + hose = pcibios_alloc_controller(); + if (hose == NULL) + return -ENOMEM; + hose->first_busno = bus_range ? bus_range[0] : 0; + hose->last_busno = bus_range ? bus_range[1] : 0xff; + hose->arch_data = dev; + setup_indirect_pci(hose, 0xfec00000, 0xfee00000); + + /* Interpret the "ranges" property */ + /* This also maps the I/O region and sets isa_io/mem_base */ + pci_process_bridge_OF_ranges(hose, dev, 1); + + return 0; +} + +static void __init linkstation_setup_arch(void) +{ + struct device_node *np; +#ifdef CONFIG_MTD_PHYSMAP + physmap_set_partitions(linkstation_physmap_partitions, + ARRAY_SIZE(linkstation_physmap_partitions)); +#endif + +#ifdef CONFIG_BLK_DEV_INITRD + if (initrd_start) + ROOT_DEV = Root_RAM0; + else +#endif +#ifdef CONFIG_ROOT_NFS + ROOT_DEV = Root_NFS; +#else + ROOT_DEV = Root_HDA1; +#endif + + /* Lookup PCI host bridges */ + for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;) + add_bridge(np); + + printk(KERN_INFO "BUFFALO Network Attached Storage Series\n"); + printk(KERN_INFO "(C) 2002-2005 BUFFALO INC.\n"); +} + +/* + * Interrupt setup and service. Interrrupts on the linkstation come + * from the four PCI slots plus onboard 8241 devices: I2C, DUART. + */ +static void __init linkstation_init_IRQ(void) +{ + struct mpic *mpic; + struct device_node *dnp; + void *prop; + int size; + phys_addr_t paddr; + + dnp = of_find_node_by_type(NULL, "open-pic"); + if (dnp == NULL) + return; + + prop = (struct device_node *)get_property(dnp, "reg", &size); + paddr = (phys_addr_t)of_translate_address(dnp, prop); + + mpic = mpic_alloc(dnp, paddr, MPIC_PRIMARY | MPIC_WANTS_RESET, 4, 32, " EPIC "); + BUG_ON(mpic == NULL); + + /* PCI IRQs */ + mpic_assign_isu(mpic, 0, paddr + 0x10200); + + /* I2C */ + mpic_assign_isu(mpic, 1, paddr + 0x11000); + + /* ttyS0, ttyS1 */ + mpic_assign_isu(mpic, 2, paddr + 0x11100); + + mpic_init(mpic); +} + +extern void avr_uart_configure(void); +extern void avr_uart_send(const char); + +static void linkstation_restart(char *cmd) +{ + local_irq_disable(); + + /* Reset system via AVR */ + avr_uart_configure(); + /* Send reboot command */ + avr_uart_send('C'); + + for(;;) /* Spin until reset happens */ + avr_uart_send('G'); /* "kick" */ +} + +static void linkstation_power_off(void) +{ + local_irq_disable(); + + /* Power down system via AVR */ + avr_uart_configure(); + /* send shutdown command */ + avr_uart_send('E'); + + for(;;) /* Spin until power-off happens */ + avr_uart_send('G'); /* "kick" */ + /* NOTREACHED */ +} + +static void linkstation_halt(void) +{ + linkstation_power_off(); + /* NOTREACHED */ +} + +static void linkstation_show_cpuinfo(struct seq_file *m) +{ + seq_printf(m, "vendor\t\t: Buffalo Technology\n"); + seq_printf(m, "machine\t\t: Linkstation I/Kurobox(HG)\n"); +} + +static int __init linkstation_probe(void) +{ + unsigned long root; + + root = of_get_flat_dt_root(); + + if (!of_flat_dt_is_compatible(root, "linkstation")) + return 0; + return 1; +} + +define_machine(linkstation){ + .name = "Buffalo Linkstation", + .probe = linkstation_probe, + .setup_arch = linkstation_setup_arch, + .init_IRQ = linkstation_init_IRQ, + .show_cpuinfo = linkstation_show_cpuinfo, + .get_irq = mpic_get_irq, + .restart = linkstation_restart, + .power_off = linkstation_power_off, + .halt = linkstation_halt, + .calibrate_decr = generic_calibrate_decr, +}; diff --git a/arch/powerpc/platforms/embedded6xx/ls_uart.c b/arch/powerpc/platforms/embedded6xx/ls_uart.c new file mode 100644 index 000000000000..31bcdae84823 --- /dev/null +++ b/arch/powerpc/platforms/embedded6xx/ls_uart.c @@ -0,0 +1,131 @@ +#include <linux/workqueue.h> +#include <linux/string.h> +#include <linux/delay.h> +#include <linux/serial_reg.h> +#include <linux/serial_8250.h> +#include <asm/io.h> +#include <asm/mpc10x.h> +#include <asm/ppc_sys.h> +#include <asm/prom.h> +#include <asm/termbits.h> + +static void __iomem *avr_addr; +static unsigned long avr_clock; + +static struct work_struct wd_work; + +static void wd_stop(void *unused) +{ + const char string[] = "AAAAFFFFJJJJ>>>>VVVV>>>>ZZZZVVVVKKKK"; + int i = 0, rescue = 8; + int len = strlen(string); + + while (rescue--) { + int j; + char lsr = in_8(avr_addr + UART_LSR); + + if (lsr & (UART_LSR_THRE | UART_LSR_TEMT)) { + for (j = 0; j < 16 && i < len; j++, i++) + out_8(avr_addr + UART_TX, string[i]); + if (i == len) { + /* Read "OK" back: 4ms for the last "KKKK" + plus a couple bytes back */ + msleep(7); + printk("linkstation: disarming the AVR watchdog: "); + while (in_8(avr_addr + UART_LSR) & UART_LSR_DR) + printk("%c", in_8(avr_addr + UART_RX)); + break; + } + } + msleep(17); + } + printk("\n"); +} + +#define AVR_QUOT(clock) ((clock) + 8 * 9600) / (16 * 9600) + +void avr_uart_configure(void) +{ + unsigned char cval = UART_LCR_WLEN8; + unsigned int quot = AVR_QUOT(avr_clock); + + if (!avr_addr || !avr_clock) + return; + + out_8(avr_addr + UART_LCR, cval); /* initialise UART */ + out_8(avr_addr + UART_MCR, 0); + out_8(avr_addr + UART_IER, 0); + + cval |= UART_LCR_STOP | UART_LCR_PARITY | UART_LCR_EPAR; + + out_8(avr_addr + UART_LCR, cval); /* Set character format */ + + out_8(avr_addr + UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */ + out_8(avr_addr + UART_DLL, quot & 0xff); /* LS of divisor */ + out_8(avr_addr + UART_DLM, quot >> 8); /* MS of divisor */ + out_8(avr_addr + UART_LCR, cval); /* reset DLAB */ + out_8(avr_addr + UART_FCR, UART_FCR_ENABLE_FIFO); /* enable FIFO */ +} + +void avr_uart_send(const char c) +{ + if (!avr_addr || !avr_clock) + return; + + out_8(avr_addr + UART_TX, c); + out_8(avr_addr + UART_TX, c); + out_8(avr_addr + UART_TX, c); + out_8(avr_addr + UART_TX, c); +} + +static void __init ls_uart_init(void) +{ + local_irq_disable(); + +#ifndef CONFIG_SERIAL_8250 + out_8(avr_addr + UART_FCR, UART_FCR_ENABLE_FIFO); /* enable FIFO */ + out_8(avr_addr + UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); /* clear FIFOs */ + out_8(avr_addr + UART_FCR, 0); + out_8(avr_addr + UART_IER, 0); + + /* Clear up interrupts */ + (void) in_8(avr_addr + UART_LSR); + (void) in_8(avr_addr + UART_RX); + (void) in_8(avr_addr + UART_IIR); + (void) in_8(avr_addr + UART_MSR); +#endif + avr_uart_configure(); + + local_irq_enable(); +} + +static int __init ls_uarts_init(void) +{ + struct device_node *avr; + phys_addr_t phys_addr; + int len; + + avr = of_find_node_by_path("/soc10x/serial@80004500"); + if (!avr) + return -EINVAL; + + avr_clock = *(u32*)get_property(avr, "clock-frequency", &len); + phys_addr = ((u32*)get_property(avr, "reg", &len))[0]; + + if (!avr_clock || !phys_addr) + return -EINVAL; + + avr_addr = ioremap(phys_addr, 32); + if (!avr_addr) + return -EFAULT; + + ls_uart_init(); + + INIT_WORK(&wd_work, wd_stop, NULL); + schedule_work(&wd_work); + + return 0; +} + +late_initcall(ls_uarts_init); diff --git a/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c b/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c index bdb475c65cba..3fcc85f60fbf 100644 --- a/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c +++ b/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c @@ -60,7 +60,7 @@ pci_dram_offset = MPC7448_HPC2_PCI_MEM_OFFSET; extern int tsi108_setup_pci(struct device_node *dev); extern void _nmask_and_or_msr(unsigned long nmask, unsigned long or_val); -extern void tsi108_pci_int_init(void); +extern void tsi108_pci_int_init(struct device_node *node); extern void tsi108_irq_cascade(unsigned int irq, struct irq_desc *desc); int mpc7448_hpc2_exclude_device(u_char bus, u_char devfn) @@ -71,65 +71,6 @@ int mpc7448_hpc2_exclude_device(u_char bus, u_char devfn) return PCIBIOS_SUCCESSFUL; } -/* - * find pci slot by devfn in interrupt map of OF tree - */ -u8 find_slot_by_devfn(unsigned int *interrupt_map, unsigned int devfn) -{ - int i; - unsigned int tmp; - for (i = 0; i < 4; i++){ - tmp = interrupt_map[i*4*7]; - if ((tmp >> 11) == (devfn >> 3)) - return i; - } - return i; -} - -/* - * Scans the interrupt map for pci device - */ -void mpc7448_hpc2_fixup_irq(struct pci_dev *dev) -{ - struct pci_controller *hose; - struct device_node *node; - const unsigned int *interrupt; - int busnr; - int len; - u8 slot; - u8 pin; - - /* Lookup the hose */ - busnr = dev->bus->number; - hose = pci_bus_to_hose(busnr); - if (!hose) - printk(KERN_ERR "No pci hose found\n"); - - /* Check it has an OF node associated */ - node = (struct device_node *) hose->arch_data; - if (!node) - printk(KERN_ERR "No pci node found\n"); - - interrupt = get_property(node, "interrupt-map", &len); - slot = find_slot_by_devfn(interrupt, dev->devfn); - pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin); - if (pin == 0 || pin > 4) - pin = 1; - pin--; - dev->irq = interrupt[slot*4*7 + pin*7 + 5]; - DBG("TSI_PCI: dev->irq = 0x%x\n", dev->irq); -} -/* temporary pci irq map fixup*/ - -void __init mpc7448_hpc2_pcibios_fixup(void) -{ - struct pci_dev *dev = NULL; - for_each_pci_dev(dev) { - mpc7448_hpc2_fixup_irq(dev); - pci_write_config_byte(dev, PCI_INTERRUPT_LINE, dev->irq); - } -} - static void __init mpc7448_hpc2_setup_arch(void) { struct device_node *cpu; @@ -192,9 +133,12 @@ static void __init mpc7448_hpc2_init_IRQ(void) { struct mpic *mpic; phys_addr_t mpic_paddr = 0; + struct device_node *tsi_pic; +#ifdef CONFIG_PCI unsigned int cascade_pci_irq; struct device_node *tsi_pci; - struct device_node *tsi_pic; + struct device_node *cascade_node = NULL; +#endif tsi_pic = of_find_node_by_type(NULL, "open-pic"); if (tsi_pic) { @@ -208,31 +152,41 @@ static void __init mpc7448_hpc2_init_IRQ(void) return; } - DBG("%s: tsi108pic phys_addr = 0x%x\n", __FUNCTION__, + DBG("%s: tsi108 pic phys_addr = 0x%x\n", __FUNCTION__, (u32) mpic_paddr); mpic = mpic_alloc(tsi_pic, mpic_paddr, MPIC_PRIMARY | MPIC_BIG_ENDIAN | MPIC_WANTS_RESET | MPIC_SPV_EOI | MPIC_NO_PTHROU_DIS | MPIC_REGSET_TSI108, - 0, /* num_sources used */ - 0, /* num_sources used */ + 24, + NR_IRQS-4, /* num_sources used */ "Tsi108_PIC"); - BUG_ON(mpic == NULL); /* XXXX */ + BUG_ON(mpic == NULL); + + mpic_assign_isu(mpic, 0, mpic_paddr + 0x100); + mpic_init(mpic); +#ifdef CONFIG_PCI tsi_pci = of_find_node_by_type(NULL, "pci"); - if (tsi_pci == 0) { + if (tsi_pci == NULL) { printk("%s: No tsi108 pci node found !\n", __FUNCTION__); return; } + cascade_node = of_find_node_by_type(NULL, "pic-router"); + if (cascade_node == NULL) { + printk("%s: No tsi108 pci cascade node found !\n", __FUNCTION__); + return; + } cascade_pci_irq = irq_of_parse_and_map(tsi_pci, 0); + DBG("%s: tsi108 cascade_pci_irq = 0x%x\n", __FUNCTION__, + (u32) cascade_pci_irq); + tsi108_pci_int_init(cascade_node); set_irq_data(cascade_pci_irq, mpic); set_irq_chained_handler(cascade_pci_irq, tsi108_irq_cascade); - - tsi108_pci_int_init(); - +#endif /* Configure MPIC outputs to CPU0 */ tsi108_write_reg(TSI108_MPIC_OFFSET + 0x30c, 0); of_node_put(tsi_pic); @@ -290,7 +244,6 @@ static int mpc7448_machine_check_exception(struct pt_regs *regs) return 1; } return 0; - } define_machine(mpc7448_hpc2){ @@ -300,7 +253,6 @@ define_machine(mpc7448_hpc2){ .init_IRQ = mpc7448_hpc2_init_IRQ, .show_cpuinfo = mpc7448_hpc2_show_cpuinfo, .get_irq = mpic_get_irq, - .pcibios_fixup = mpc7448_hpc2_pcibios_fixup, .restart = mpc7448_hpc2_restart, .calibrate_decr = generic_calibrate_decr, .machine_check_exception= mpc7448_machine_check_exception, |