diff options
Diffstat (limited to 'arch/mips/au1000/pb1000/board_setup.c')
| -rw-r--r-- | arch/mips/au1000/pb1000/board_setup.c | 182 |
1 files changed, 182 insertions, 0 deletions
diff --git a/arch/mips/au1000/pb1000/board_setup.c b/arch/mips/au1000/pb1000/board_setup.c new file mode 100644 index 000000000000..2fa211b69329 --- /dev/null +++ b/arch/mips/au1000/pb1000/board_setup.c @@ -0,0 +1,182 @@ +/* + * Copyright 2000 MontaVista Software Inc. + * Author: MontaVista Software, Inc. + * ppopov@mvista.com or source@mvista.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include <linux/config.h> +#include <linux/init.h> +#include <linux/sched.h> +#include <linux/ioport.h> +#include <linux/mm.h> +#include <linux/console.h> +#include <linux/delay.h> + +#include <asm/cpu.h> +#include <asm/bootinfo.h> +#include <asm/irq.h> +#include <asm/mipsregs.h> +#include <asm/reboot.h> +#include <asm/pgtable.h> +#include <asm/mach-au1x00/au1000.h> +#include <asm/mach-pb1x00/pb1000.h> + +void board_reset (void) +{ +} + +void __init board_setup(void) +{ + u32 pin_func, static_cfg0; + u32 sys_freqctrl, sys_clksrc; + u32 prid = read_c0_prid(); + + // set AUX clock to 12MHz * 8 = 96 MHz + au_writel(8, SYS_AUXPLL); + au_writel(0, SYS_PINSTATERD); + udelay(100); + +#if defined (CONFIG_USB_OHCI) || defined (CONFIG_AU1X00_USB_DEVICE) + /* zero and disable FREQ2 */ + sys_freqctrl = au_readl(SYS_FREQCTRL0); + sys_freqctrl &= ~0xFFF00000; + au_writel(sys_freqctrl, SYS_FREQCTRL0); + + /* zero and disable USBH/USBD clocks */ + sys_clksrc = au_readl(SYS_CLKSRC); + sys_clksrc &= ~0x00007FE0; + au_writel(sys_clksrc, SYS_CLKSRC); + + sys_freqctrl = au_readl(SYS_FREQCTRL0); + sys_freqctrl &= ~0xFFF00000; + + sys_clksrc = au_readl(SYS_CLKSRC); + sys_clksrc &= ~0x00007FE0; + + switch (prid & 0x000000FF) + { + case 0x00: /* DA */ + case 0x01: /* HA */ + case 0x02: /* HB */ + /* CPU core freq to 48MHz to slow it way down... */ + au_writel(4, SYS_CPUPLL); + + /* + * Setup 48MHz FREQ2 from CPUPLL for USB Host + */ + /* FRDIV2=3 -> div by 8 of 384MHz -> 48MHz */ + sys_freqctrl |= ((3<<22) | (1<<21) | (0<<20)); + au_writel(sys_freqctrl, SYS_FREQCTRL0); + + /* CPU core freq to 384MHz */ + au_writel(0x20, SYS_CPUPLL); + + printk("Au1000: 48MHz OHCI workaround enabled\n"); + break; + + default: /* HC and newer */ + // FREQ2 = aux/2 = 48 MHz + sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20)); + au_writel(sys_freqctrl, SYS_FREQCTRL0); + break; + } + + /* + * Route 48MHz FREQ2 into USB Host and/or Device + */ +#ifdef CONFIG_USB_OHCI + sys_clksrc |= ((4<<12) | (0<<11) | (0<<10)); +#endif +#ifdef CONFIG_AU1X00_USB_DEVICE + sys_clksrc |= ((4<<7) | (0<<6) | (0<<5)); +#endif + au_writel(sys_clksrc, SYS_CLKSRC); + + // configure pins GPIO[14:9] as GPIO + pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8080); + +#ifndef CONFIG_AU1X00_USB_DEVICE + // 2nd USB port is USB host + pin_func |= 0x8000; +#endif + au_writel(pin_func, SYS_PINFUNC); + au_writel(0x2800, SYS_TRIOUTCLR); + au_writel(0x0030, SYS_OUTPUTCLR); +#endif // defined (CONFIG_USB_OHCI) || defined (CONFIG_AU1X00_USB_DEVICE) + + // make gpio 15 an input (for interrupt line) + pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x100); + // we don't need I2S, so make it available for GPIO[31:29] + pin_func |= (1<<5); + au_writel(pin_func, SYS_PINFUNC); + + au_writel(0x8000, SYS_TRIOUTCLR); + + static_cfg0 = au_readl(MEM_STCFG0) & (u32)(~0xc00); + au_writel(static_cfg0, MEM_STCFG0); + + // configure RCE2* for LCD + au_writel(0x00000004, MEM_STCFG2); + + // MEM_STTIME2 + au_writel(0x09000000, MEM_STTIME2); + + // Set 32-bit base address decoding for RCE2* + au_writel(0x10003ff0, MEM_STADDR2); + + // PCI CPLD setup + // expand CE0 to cover PCI + au_writel(0x11803e40, MEM_STADDR1); + + // burst visibility on + au_writel(au_readl(MEM_STCFG0) | 0x1000, MEM_STCFG0); + + au_writel(0x83, MEM_STCFG1); // ewait enabled, flash timing + au_writel(0x33030a10, MEM_STTIME1); // slower timing for FPGA + + /* setup the static bus controller */ + au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */ + au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */ + au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */ + +#ifdef CONFIG_PCI + au_writel(0, PCI_BRIDGE_CONFIG); // set extend byte to 0 + au_writel(0, SDRAM_MBAR); // set mbar to 0 + au_writel(0x2, SDRAM_CMD); // enable memory accesses + au_sync_delay(1); +#endif + + /* Enable Au1000 BCLK switching - note: sed1356 must not use + * its BCLK (Au1000 LCLK) for any timings */ + switch (prid & 0x000000FF) + { + case 0x00: /* DA */ + case 0x01: /* HA */ + case 0x02: /* HB */ + break; + default: /* HC and newer */ + /* Enable sys bus clock divider when IDLE state or no bus + activity. */ + au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL); + break; + } +} |