diff options
Diffstat (limited to 'arch/arm')
133 files changed, 2011 insertions, 3661 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 1cacda426a0e..006f9838dd43 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -15,6 +15,7 @@ config ARM select GENERIC_IRQ_SHOW select GENERIC_PCI_IOMAP select GENERIC_SMP_IDLE_THREAD + select GENERIC_IDLE_POLL_SETUP select GENERIC_STRNCPY_FROM_USER select GENERIC_STRNLEN_USER select HARDIRQS_SW_RESEND @@ -549,6 +550,8 @@ config ARCH_IXP4XX select GENERIC_CLOCKEVENTS select MIGHT_HAVE_PCI select NEED_MACH_IO_H + select USB_EHCI_BIG_ENDIAN_MMIO + select USB_EHCI_BIG_ENDIAN_DESC help Support for Intel's IXP4XX (XScale) family of processors. @@ -2160,7 +2163,6 @@ endmenu menu "CPU Power Management" if ARCH_HAS_CPUFREQ - source "drivers/cpufreq/Kconfig" config CPU_FREQ_IMX @@ -2170,30 +2172,6 @@ config CPU_FREQ_IMX help This enables the CPUfreq driver for i.MX CPUs. -config CPU_FREQ_SA1100 - bool - -config CPU_FREQ_SA1110 - bool - -config CPU_FREQ_INTEGRATOR - tristate "CPUfreq driver for ARM Integrator CPUs" - depends on ARCH_INTEGRATOR && CPU_FREQ - default y - help - This enables the CPUfreq driver for ARM Integrator CPUs. - - For details, take a look at <file:Documentation/cpu-freq>. - - If in doubt, say Y. - -config CPU_FREQ_PXA - bool - depends on CPU_FREQ && ARCH_PXA && PXA25x - default y - select CPU_FREQ_DEFAULT_GOV_USERSPACE - select CPU_FREQ_TABLE - config CPU_FREQ_S3C bool help diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi index cb7bcc51608d..39253b9aedd1 100644 --- a/arch/arm/boot/dts/at91sam9260.dtsi +++ b/arch/arm/boot/dts/at91sam9260.dtsi @@ -322,6 +322,24 @@ }; }; + spi0 { + pinctrl_spi0: spi0-0 { + atmel,pins = + <0 0 0x1 0x0 /* PA0 periph A SPI0_MISO pin */ + 0 1 0x1 0x0 /* PA1 periph A SPI0_MOSI pin */ + 0 2 0x1 0x0>; /* PA2 periph A SPI0_SPCK pin */ + }; + }; + + spi1 { + pinctrl_spi1: spi1-0 { + atmel,pins = + <1 0 0x1 0x0 /* PB0 periph A SPI1_MISO pin */ + 1 1 0x1 0x0 /* PB1 periph A SPI1_MOSI pin */ + 1 2 0x1 0x0>; /* PB2 periph A SPI1_SPCK pin */ + }; + }; + pioA: gpio@fffff400 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffff400 0x200>; @@ -471,6 +489,28 @@ status = "disabled"; }; + spi0: spi@fffc8000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffc8000 0x200>; + interrupts = <12 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0>; + status = "disabled"; + }; + + spi1: spi@fffcc000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffcc000 0x200>; + interrupts = <13 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1>; + status = "disabled"; + }; + adc0: adc@fffe0000 { compatible = "atmel,at91sam9260-adc"; reg = <0xfffe0000 0x100>; diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi index 271d4de026e9..94b58ab2cc08 100644 --- a/arch/arm/boot/dts/at91sam9263.dtsi +++ b/arch/arm/boot/dts/at91sam9263.dtsi @@ -303,6 +303,24 @@ }; }; + spi0 { + pinctrl_spi0: spi0-0 { + atmel,pins = + <0 0 0x2 0x0 /* PA0 periph B SPI0_MISO pin */ + 0 1 0x2 0x0 /* PA1 periph B SPI0_MOSI pin */ + 0 2 0x2 0x0>; /* PA2 periph B SPI0_SPCK pin */ + }; + }; + + spi1 { + pinctrl_spi1: spi1-0 { + atmel,pins = + <1 12 0x1 0x0 /* PB12 periph A SPI1_MISO pin */ + 1 13 0x1 0x0 /* PB13 periph A SPI1_MOSI pin */ + 1 14 0x1 0x0>; /* PB14 periph A SPI1_SPCK pin */ + }; + }; + pioA: gpio@fffff200 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffff200 0x200>; @@ -462,6 +480,28 @@ reg = <0xfffffd40 0x10>; status = "disabled"; }; + + spi0: spi@fffa4000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffa4000 0x200>; + interrupts = <14 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0>; + status = "disabled"; + }; + + spi1: spi@fffa8000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffa8000 0x200>; + interrupts = <15 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1>; + status = "disabled"; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts index 1eb08728f527..a14e424b2e81 100644 --- a/arch/arm/boot/dts/at91sam9263ek.dts +++ b/arch/arm/boot/dts/at91sam9263ek.dts @@ -79,6 +79,16 @@ }; }; }; + + spi0: spi@fffa4000 { + status = "okay"; + cs-gpios = <&pioA 5 0>, <0>, <0>, <0>; + mtd_dataflash@0 { + compatible = "atmel,at45", "atmel,dataflash"; + spi-max-frequency = <50000000>; + reg = <0>; + }; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi index da15e83e7f17..23d1f468f27f 100644 --- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi +++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi @@ -96,6 +96,16 @@ status = "okay"; pinctrl-0 = <&pinctrl_ssc0_tx>; }; + + spi0: spi@fffc8000 { + status = "okay"; + cs-gpios = <0>, <&pioC 11 0>, <0>, <0>; + mtd_dataflash@0 { + compatible = "atmel,at45", "atmel,dataflash"; + spi-max-frequency = <50000000>; + reg = <1>; + }; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi index 6b1d4cab24c2..cfdf429578b5 100644 --- a/arch/arm/boot/dts/at91sam9g45.dtsi +++ b/arch/arm/boot/dts/at91sam9g45.dtsi @@ -322,6 +322,24 @@ }; }; + spi0 { + pinctrl_spi0: spi0-0 { + atmel,pins = + <1 0 0x1 0x0 /* PB0 periph A SPI0_MISO pin */ + 1 1 0x1 0x0 /* PB1 periph A SPI0_MOSI pin */ + 1 2 0x1 0x0>; /* PB2 periph A SPI0_SPCK pin */ + }; + }; + + spi1 { + pinctrl_spi1: spi1-0 { + atmel,pins = + <1 14 0x1 0x0 /* PB14 periph A SPI1_MISO pin */ + 1 15 0x1 0x0 /* PB15 periph A SPI1_MOSI pin */ + 1 16 0x1 0x0>; /* PB16 periph A SPI1_SPCK pin */ + }; + }; + pioA: gpio@fffff200 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffff200 0x200>; @@ -531,6 +549,28 @@ reg = <0xfffffd40 0x10>; status = "disabled"; }; + + spi0: spi@fffa4000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffa4000 0x200>; + interrupts = <14 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0>; + status = "disabled"; + }; + + spi1: spi@fffa8000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffa8000 0x200>; + interrupts = <15 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1>; + status = "disabled"; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts index 20c31913c270..92c52a7d70bc 100644 --- a/arch/arm/boot/dts/at91sam9m10g45ek.dts +++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts @@ -102,6 +102,16 @@ }; }; }; + + spi0: spi@fffa4000{ + status = "okay"; + cs-gpios = <&pioB 3 0>, <0>, <0>, <0>; + mtd_dataflash@0 { + compatible = "atmel,at45", "atmel,dataflash"; + spi-max-frequency = <13000000>; + reg = <0>; + }; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi index 7750f98dd764..b2961f1ea51b 100644 --- a/arch/arm/boot/dts/at91sam9n12.dtsi +++ b/arch/arm/boot/dts/at91sam9n12.dtsi @@ -261,6 +261,24 @@ }; }; + spi0 { + pinctrl_spi0: spi0-0 { + atmel,pins = + <0 11 0x1 0x0 /* PA11 periph A SPI0_MISO pin */ + 0 12 0x1 0x0 /* PA12 periph A SPI0_MOSI pin */ + 0 13 0x1 0x0>; /* PA13 periph A SPI0_SPCK pin */ + }; + }; + + spi1 { + pinctrl_spi1: spi1-0 { + atmel,pins = + <0 21 0x2 0x0 /* PA21 periph B SPI1_MISO pin */ + 0 22 0x2 0x0 /* PA22 periph B SPI1_MOSI pin */ + 0 23 0x2 0x0>; /* PA23 periph B SPI1_SPCK pin */ + }; + }; + pioA: gpio@fffff400 { compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; reg = <0xfffff400 0x200>; @@ -373,6 +391,28 @@ #size-cells = <0>; status = "disabled"; }; + + spi0: spi@f0000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xf0000000 0x100>; + interrupts = <13 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0>; + status = "disabled"; + }; + + spi1: spi@f0004000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xf0004000 0x100>; + interrupts = <14 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1>; + status = "disabled"; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts index d400f8de4387..34c842b1efb2 100644 --- a/arch/arm/boot/dts/at91sam9n12ek.dts +++ b/arch/arm/boot/dts/at91sam9n12ek.dts @@ -67,6 +67,16 @@ }; }; }; + + spi0: spi@f0000000 { + status = "okay"; + cs-gpios = <&pioA 14 0>, <0>, <0>, <0>; + m25p80@0 { + compatible = "atmel,at25df321a"; + spi-max-frequency = <50000000>; + reg = <0>; + }; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index a98c0d50fbbe..347b438d47fa 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -343,6 +343,24 @@ }; }; + spi0 { + pinctrl_spi0: spi0-0 { + atmel,pins = + <0 11 0x1 0x0 /* PA11 periph A SPI0_MISO pin */ + 0 12 0x1 0x0 /* PA12 periph A SPI0_MOSI pin */ + 0 13 0x1 0x0>; /* PA13 periph A SPI0_SPCK pin */ + }; + }; + + spi1 { + pinctrl_spi1: spi1-0 { + atmel,pins = + <0 21 0x2 0x0 /* PA21 periph B SPI1_MISO pin */ + 0 22 0x2 0x0 /* PA22 periph B SPI1_MOSI pin */ + 0 23 0x2 0x0>; /* PA23 periph B SPI1_SPCK pin */ + }; + }; + pioA: gpio@fffff400 { compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; reg = <0xfffff400 0x200>; @@ -529,6 +547,28 @@ trigger-value = <0x6>; }; }; + + spi0: spi@f0000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xf0000000 0x100>; + interrupts = <13 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0>; + status = "disabled"; + }; + + spi1: spi@f0004000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-spi"; + reg = <0xf0004000 0x100>; + interrupts = <14 4 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1>; + status = "disabled"; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9x5ek.dtsi b/arch/arm/boot/dts/at91sam9x5ek.dtsi index 8a7cf1d9cf5d..09f5e667ca7a 100644 --- a/arch/arm/boot/dts/at91sam9x5ek.dtsi +++ b/arch/arm/boot/dts/at91sam9x5ek.dtsi @@ -84,6 +84,16 @@ }; }; }; + + spi0: spi@f0000000 { + status = "okay"; + cs-gpios = <&pioA 14 0>, <0>, <0>, <0>; + m25p80@0 { + compatible = "atmel,at25df321a"; + spi-max-frequency = <50000000>; + reg = <0>; + }; + }; }; usb0: ohci@00600000 { diff --git a/arch/arm/boot/dts/msm8660-surf.dts b/arch/arm/boot/dts/msm8660-surf.dts index 31f2157cd7d7..67f8670c4d6a 100644 --- a/arch/arm/boot/dts/msm8660-surf.dts +++ b/arch/arm/boot/dts/msm8660-surf.dts @@ -38,4 +38,10 @@ <0x19c00000 0x1000>; interrupts = <0 195 0x0>; }; + + qcom,ssbi@500000 { + compatible = "qcom,ssbi"; + reg = <0x500000 0x1000>; + qcom,controller-type = "pmic-arbiter"; + }; }; diff --git a/arch/arm/boot/dts/msm8960-cdp.dts b/arch/arm/boot/dts/msm8960-cdp.dts index 9e621b5ad3dd..c9b09a813a4b 100644 --- a/arch/arm/boot/dts/msm8960-cdp.dts +++ b/arch/arm/boot/dts/msm8960-cdp.dts @@ -38,4 +38,10 @@ <0x16400000 0x1000>; interrupts = <0 154 0x0>; }; + + qcom,ssbi@500000 { + compatible = "qcom,ssbi"; + reg = <0x500000 0x1000>; + qcom,controller-type = "pmic-arbiter"; + }; }; diff --git a/arch/arm/boot/dts/spear1310.dtsi b/arch/arm/boot/dts/spear1310.dtsi index 1513c1927cc8..122ae94076c8 100644 --- a/arch/arm/boot/dts/spear1310.dtsi +++ b/arch/arm/boot/dts/spear1310.dtsi @@ -89,7 +89,7 @@ pinmux: pinmux@e0700000 { compatible = "st,spear1310-pinmux"; reg = <0xe0700000 0x1000>; - #gpio-range-cells = <2>; + #gpio-range-cells = <3>; }; apb { @@ -212,7 +212,7 @@ interrupt-controller; gpio-controller; #gpio-cells = <2>; - gpio-ranges = <&pinmux 0 246>; + gpio-ranges = <&pinmux 0 0 246>; status = "disabled"; st-plgpio,ngpio = <246>; diff --git a/arch/arm/boot/dts/spear1340.dtsi b/arch/arm/boot/dts/spear1340.dtsi index 34da11aa6795..c511c4772efd 100644 --- a/arch/arm/boot/dts/spear1340.dtsi +++ b/arch/arm/boot/dts/spear1340.dtsi @@ -63,7 +63,7 @@ pinmux: pinmux@e0700000 { compatible = "st,spear1340-pinmux"; reg = <0xe0700000 0x1000>; - #gpio-range-cells = <2>; + #gpio-range-cells = <3>; }; pwm: pwm@e0180000 { @@ -127,7 +127,7 @@ interrupt-controller; gpio-controller; #gpio-cells = <2>; - gpio-ranges = <&pinmux 0 252>; + gpio-ranges = <&pinmux 0 0 252>; status = "disabled"; st-plgpio,ngpio = <250>; diff --git a/arch/arm/boot/dts/spear310.dtsi b/arch/arm/boot/dts/spear310.dtsi index ab45b8c81982..95372080eea6 100644 --- a/arch/arm/boot/dts/spear310.dtsi +++ b/arch/arm/boot/dts/spear310.dtsi @@ -25,7 +25,7 @@ pinmux: pinmux@b4000000 { compatible = "st,spear310-pinmux"; reg = <0xb4000000 0x1000>; - #gpio-range-cells = <2>; + #gpio-range-cells = <3>; }; fsmc: flash@44000000 { @@ -102,7 +102,7 @@ interrupt-controller; gpio-controller; #gpio-cells = <2>; - gpio-ranges = <&pinmux 0 102>; + gpio-ranges = <&pinmux 0 0 102>; status = "disabled"; st-plgpio,ngpio = <102>; diff --git a/arch/arm/boot/dts/spear320.dtsi b/arch/arm/boot/dts/spear320.dtsi index caa5520b1fd4..ffea342aeec9 100644 --- a/arch/arm/boot/dts/spear320.dtsi +++ b/arch/arm/boot/dts/spear320.dtsi @@ -24,7 +24,7 @@ pinmux: pinmux@b3000000 { compatible = "st,spear320-pinmux"; reg = <0xb3000000 0x1000>; - #gpio-range-cells = <2>; + #gpio-range-cells = <3>; }; clcd@90000000 { @@ -130,7 +130,7 @@ interrupt-controller; gpio-controller; #gpio-cells = <2>; - gpio-ranges = <&pinmux 0 102>; + gpio-ranges = <&pinmux 0 0 102>; status = "disabled"; st-plgpio,ngpio = <102>; diff --git a/arch/arm/boot/dts/vt8500-bv07.dts b/arch/arm/boot/dts/vt8500-bv07.dts index 567cf4e8ab84..877b33afa7ed 100644 --- a/arch/arm/boot/dts/vt8500-bv07.dts +++ b/arch/arm/boot/dts/vt8500-bv07.dts @@ -11,26 +11,22 @@ / { model = "Benign BV07 Netbook"; +}; - /* - * Display node is based on Sascha Hauer's patch on dri-devel. - * Added a bpp property to calculate the size of the framebuffer - * until the binding is formalized. - */ - display: display@0 { - modes { - mode0: mode@0 { - hactive = <800>; - vactive = <480>; - hback-porch = <88>; - hfront-porch = <40>; - hsync-len = <0>; - vback-porch = <32>; - vfront-porch = <11>; - vsync-len = <1>; - clock = <0>; /* unused but required */ - bpp = <16>; /* non-standard but required */ - }; +&fb { + bits-per-pixel = <16>; + display-timings { + native-mode = <&timing0>; + timing0: 800x480 { + clock-frequency = <0>; /* unused but required */ + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <88>; + hsync-len = <0>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <1>; }; }; }; diff --git a/arch/arm/boot/dts/vt8500.dtsi b/arch/arm/boot/dts/vt8500.dtsi index cf31ced46602..68c8dc644383 100644 --- a/arch/arm/boot/dts/vt8500.dtsi +++ b/arch/arm/boot/dts/vt8500.dtsi @@ -98,12 +98,10 @@ interrupts = <43>; }; - fb@d800e400 { + fb: fb@d8050800 { compatible = "via,vt8500-fb"; reg = <0xd800e400 0x400>; interrupts = <12>; - display = <&display>; - default-mode = <&mode0>; }; ge_rops@d8050400 { diff --git a/arch/arm/boot/dts/wm8505-ref.dts b/arch/arm/boot/dts/wm8505-ref.dts index fd4e248074c6..edd2cec3d37f 100644 --- a/arch/arm/boot/dts/wm8505-ref.dts +++ b/arch/arm/boot/dts/wm8505-ref.dts @@ -11,26 +11,22 @@ / { model = "Wondermedia WM8505 Netbook"; +}; - /* - * Display node is based on Sascha Hauer's patch on dri-devel. - * Added a bpp property to calculate the size of the framebuffer - * until the binding is formalized. - */ - display: display@0 { - modes { - mode0: mode@0 { - hactive = <800>; - vactive = <480>; - hback-porch = <88>; - hfront-porch = <40>; - hsync-len = <0>; - vback-porch = <32>; - vfront-porch = <11>; - vsync-len = <1>; - clock = <0>; /* unused but required */ - bpp = <32>; /* non-standard but required */ - }; +&fb { + bits-per-pixel = <32>; + display-timings { + native-mode = <&timing0>; + timing0: 800x480 { + clock-frequency = <0>; /* unused but required */ + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <88>; + hsync-len = <0>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <1>; }; }; }; diff --git a/arch/arm/boot/dts/wm8505.dtsi b/arch/arm/boot/dts/wm8505.dtsi index e74a1c0fb9a2..bcf668d31b28 100644 --- a/arch/arm/boot/dts/wm8505.dtsi +++ b/arch/arm/boot/dts/wm8505.dtsi @@ -128,11 +128,9 @@ interrupts = <0>; }; - fb@d8050800 { + fb: fb@d8050800 { compatible = "wm,wm8505-fb"; reg = <0xd8050800 0x200>; - display = <&display>; - default-mode = <&mode0>; }; ge_rops@d8050400 { diff --git a/arch/arm/boot/dts/wm8650-mid.dts b/arch/arm/boot/dts/wm8650-mid.dts index cefd938f842f..61671a0d9ede 100644 --- a/arch/arm/boot/dts/wm8650-mid.dts +++ b/arch/arm/boot/dts/wm8650-mid.dts @@ -11,26 +11,24 @@ / { model = "Wondermedia WM8650-MID Tablet"; +}; + +&fb { + bits-per-pixel = <16>; - /* - * Display node is based on Sascha Hauer's patch on dri-devel. - * Added a bpp property to calculate the size of the framebuffer - * until the binding is formalized. - */ - display: display@0 { - modes { - mode0: mode@0 { - hactive = <800>; - vactive = <480>; - hback-porch = <88>; - hfront-porch = <40>; - hsync-len = <0>; - vback-porch = <32>; - vfront-porch = <11>; - vsync-len = <1>; - clock = <0>; /* unused but required */ - bpp = <16>; /* non-standard but required */ - }; + display-timings { + native-mode = <&timing0>; + timing0: 800x480 { + clock-frequency = <0>; /* unused but required */ + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <88>; + hsync-len = <0>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <1>; }; }; }; + diff --git a/arch/arm/boot/dts/wm8650.dtsi b/arch/arm/boot/dts/wm8650.dtsi index db3c0a12e052..9313407bbc30 100644 --- a/arch/arm/boot/dts/wm8650.dtsi +++ b/arch/arm/boot/dts/wm8650.dtsi @@ -128,11 +128,9 @@ interrupts = <43>; }; - fb@d8050800 { + fb: fb@d8050800 { compatible = "wm,wm8505-fb"; reg = <0xd8050800 0x200>; - display = <&display>; - default-mode = <&mode0>; }; ge_rops@d8050400 { diff --git a/arch/arm/boot/dts/wm8850-w70v2.dts b/arch/arm/boot/dts/wm8850-w70v2.dts index fcc660c89540..32d22532cd6c 100644 --- a/arch/arm/boot/dts/wm8850-w70v2.dts +++ b/arch/arm/boot/dts/wm8850-w70v2.dts @@ -15,28 +15,6 @@ / { model = "Wondermedia WM8850-W70v2 Tablet"; - /* - * Display node is based on Sascha Hauer's patch on dri-devel. - * Added a bpp property to calculate the size of the framebuffer - * until the binding is formalized. - */ - display: display@0 { - modes { - mode0: mode@0 { - hactive = <800>; - vactive = <480>; - hback-porch = <88>; - hfront-porch = <40>; - hsync-len = <0>; - vback-porch = <32>; - vfront-porch = <11>; - vsync-len = <1>; - clock = <0>; /* unused but required */ - bpp = <16>; /* non-standard but required */ - }; - }; - }; - backlight { compatible = "pwm-backlight"; pwms = <&pwm 0 50000 1>; /* duty inverted */ @@ -45,3 +23,21 @@ default-brightness-level = <5>; }; }; + +&fb { + bits-per-pixel = <16>; + display-timings { + native-mode = <&timing0>; + timing0: 800x480 { + clock-frequency = <0>; /* unused but required */ + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <88>; + hsync-len = <0>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/wm8850.dtsi b/arch/arm/boot/dts/wm8850.dtsi index e8cbfdc87bba..7149cd13e3b9 100644 --- a/arch/arm/boot/dts/wm8850.dtsi +++ b/arch/arm/boot/dts/wm8850.dtsi @@ -135,11 +135,9 @@ }; }; - fb@d8051700 { + fb: fb@d8051700 { compatible = "wm,wm8505-fb"; reg = <0xd8051700 0x200>; - display = <&display>; - default-mode = <&mode0>; }; ge_rops@d8050400 { diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig index e36b01025321..088d6c11a0fa 100644 --- a/arch/arm/configs/imx_v6_v7_defconfig +++ b/arch/arm/configs/imx_v6_v7_defconfig @@ -188,6 +188,7 @@ CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_MXC=y CONFIG_USB_CHIPIDEA=y CONFIG_USB_CHIPIDEA_HOST=y +CONFIG_USB_PHY=y CONFIG_USB_MXS_PHY=y CONFIG_USB_STORAGE=y CONFIG_MMC=y diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig index 13482ea58b09..93f3794ba5cb 100644 --- a/arch/arm/configs/kirkwood_defconfig +++ b/arch/arm/configs/kirkwood_defconfig @@ -56,7 +56,6 @@ CONFIG_AEABI=y CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 CONFIG_CPU_IDLE=y -CONFIG_CPU_IDLE_KIRKWOOD=y CONFIG_NET=y CONFIG_PACKET=y CONFIG_UNIX=y diff --git a/arch/arm/configs/lpc32xx_defconfig b/arch/arm/configs/lpc32xx_defconfig index 92386b20bd09..afa7249fac6e 100644 --- a/arch/arm/configs/lpc32xx_defconfig +++ b/arch/arm/configs/lpc32xx_defconfig @@ -134,6 +134,7 @@ CONFIG_SND_DEBUG_VERBOSE=y # CONFIG_SND_SPI is not set CONFIG_SND_SOC=y CONFIG_USB=y +CONFIG_USB_PHY=y CONFIG_USB_OHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y diff --git a/arch/arm/configs/mxs_defconfig b/arch/arm/configs/mxs_defconfig index 6a99e30f81d2..87924d671115 100644 --- a/arch/arm/configs/mxs_defconfig +++ b/arch/arm/configs/mxs_defconfig @@ -120,6 +120,7 @@ CONFIG_USB_EHCI_HCD=y CONFIG_USB_CHIPIDEA=y CONFIG_USB_CHIPIDEA_HOST=y CONFIG_USB_STORAGE=y +CONFIG_USB_PHY=y CONFIG_USB_MXS_PHY=y CONFIG_MMC=y CONFIG_MMC_MXS=y diff --git a/arch/arm/configs/omap1_defconfig b/arch/arm/configs/omap1_defconfig index 42eab9a2a0fd..7e0ebb64a7f9 100644 --- a/arch/arm/configs/omap1_defconfig +++ b/arch/arm/configs/omap1_defconfig @@ -195,6 +195,7 @@ CONFIG_SND_SOC=y CONFIG_SND_OMAP_SOC=y # CONFIG_USB_HID is not set CONFIG_USB=y +CONFIG_USB_PHY=y CONFIG_USB_DEBUG=y CONFIG_USB_DEVICEFS=y # CONFIG_USB_DEVICE_CLASS is not set diff --git a/arch/arm/include/asm/pgtable.h b/arch/arm/include/asm/pgtable.h index 80d6fc4dbe4a..9bcd262a9008 100644 --- a/arch/arm/include/asm/pgtable.h +++ b/arch/arm/include/asm/pgtable.h @@ -61,6 +61,15 @@ extern void __pgd_error(const char *file, int line, pgd_t); #define FIRST_USER_ADDRESS PAGE_SIZE /* + * Use TASK_SIZE as the ceiling argument for free_pgtables() and + * free_pgd_range() to avoid freeing the modules pmd when LPAE is enabled (pmd + * page shared between user and kernel). + */ +#ifdef CONFIG_ARM_LPAE +#define USER_PGTABLES_CEILING TASK_SIZE +#endif + +/* * The pgprot_* and protection_map entries will be fixed up in runtime * to include the cachable and bufferable bits based on memory policy, * as well as any architecture dependent bits like global/ASID and SMP diff --git a/arch/arm/include/asm/system_misc.h b/arch/arm/include/asm/system_misc.h index 5a85f148b607..21a23e378bbe 100644 --- a/arch/arm/include/asm/system_misc.h +++ b/arch/arm/include/asm/system_misc.h @@ -21,9 +21,6 @@ extern void (*arm_pm_idle)(void); extern unsigned int user_debug; -extern void disable_hlt(void); -extern void enable_hlt(void); - #endif /* !__ASSEMBLY__ */ #endif /* __ASM_ARM_SYSTEM_MISC_H */ diff --git a/arch/arm/include/asm/unistd.h b/arch/arm/include/asm/unistd.h index e4ddfb39ca34..141baa3f9a72 100644 --- a/arch/arm/include/asm/unistd.h +++ b/arch/arm/include/asm/unistd.h @@ -44,14 +44,6 @@ #define __ARCH_WANT_SYS_CLONE /* - * "Conditional" syscalls - * - * What we want is __attribute__((weak,alias("sys_ni_syscall"))), - * but it doesn't work on all toolchains, so we just do it by hand - */ -#define cond_syscall(x) asm(".weak\t" #x "\n\t.set\t" #x ",sys_ni_syscall") - -/* * Unimplemented (or alternatively implemented) syscalls */ #define __IGNORE_fadvise64_64 diff --git a/arch/arm/kernel/early_printk.c b/arch/arm/kernel/early_printk.c index 85aa2b292692..43076536965c 100644 --- a/arch/arm/kernel/early_printk.c +++ b/arch/arm/kernel/early_printk.c @@ -29,28 +29,17 @@ static void early_console_write(struct console *con, const char *s, unsigned n) early_write(s, n); } -static struct console early_console = { +static struct console early_console_dev = { .name = "earlycon", .write = early_console_write, .flags = CON_PRINTBUFFER | CON_BOOT, .index = -1, }; -asmlinkage void early_printk(const char *fmt, ...) -{ - char buf[512]; - int n; - va_list ap; - - va_start(ap, fmt); - n = vscnprintf(buf, sizeof(buf), fmt, ap); - early_write(buf, n); - va_end(ap); -} - static int __init setup_early_printk(char *buf) { - register_console(&early_console); + early_console = &early_console_dev; + register_console(&early_console_dev); return 0; } diff --git a/arch/arm/kernel/etm.c b/arch/arm/kernel/etm.c index 9b6de8c988f3..8ff0ecdc637f 100644 --- a/arch/arm/kernel/etm.c +++ b/arch/arm/kernel/etm.c @@ -254,7 +254,7 @@ static void sysrq_etm_dump(int key) static struct sysrq_key_op sysrq_etm_op = { .handler = sysrq_etm_dump, - .help_msg = "ETM buffer dump", + .help_msg = "etm-buffer-dump(v)", .action_msg = "etm", }; diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 047d3e40e470..ae58d3b37d9d 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -57,38 +57,6 @@ static const char *isa_modes[] = { "ARM" , "Thumb" , "Jazelle", "ThumbEE" }; -static volatile int hlt_counter; - -void disable_hlt(void) -{ - hlt_counter++; -} - -EXPORT_SYMBOL(disable_hlt); - -void enable_hlt(void) -{ - hlt_counter--; - BUG_ON(hlt_counter < 0); -} - -EXPORT_SYMBOL(enable_hlt); - -static int __init nohlt_setup(char *__unused) -{ - hlt_counter = 1; - return 1; -} - -static int __init hlt_setup(char *__unused) -{ - hlt_counter = 0; - return 1; -} - -__setup("nohlt", nohlt_setup); -__setup("hlt", hlt_setup); - extern void call_with_stack(void (*fn)(void *), void *arg, void *sp); typedef void (*phys_reset_t)(unsigned long); @@ -172,54 +140,38 @@ static void default_idle(void) local_irq_enable(); } -/* - * The idle thread. - * We always respect 'hlt_counter' to prevent low power idle. - */ -void cpu_idle(void) +void arch_cpu_idle_prepare(void) { local_fiq_enable(); +} - /* endless idle loop with no priority at all */ - while (1) { - tick_nohz_idle_enter(); - rcu_idle_enter(); - ledtrig_cpu(CPU_LED_IDLE_START); - while (!need_resched()) { -#ifdef CONFIG_HOTPLUG_CPU - if (cpu_is_offline(smp_processor_id())) - cpu_die(); +void arch_cpu_idle_enter(void) +{ + ledtrig_cpu(CPU_LED_IDLE_START); +#ifdef CONFIG_PL310_ERRATA_769419 + wmb(); #endif +} - /* - * We need to disable interrupts here - * to ensure we don't miss a wakeup call. - */ - local_irq_disable(); -#ifdef CONFIG_PL310_ERRATA_769419 - wmb(); +void arch_cpu_idle_exit(void) +{ + ledtrig_cpu(CPU_LED_IDLE_END); +} + +#ifdef CONFIG_HOTPLUG_CPU +void arch_cpu_idle_dead(void) +{ + cpu_die(); +} #endif - if (hlt_counter) { - local_irq_enable(); - cpu_relax(); - } else if (!need_resched()) { - stop_critical_timings(); - if (cpuidle_idle_call()) - default_idle(); - start_critical_timings(); - /* - * default_idle functions must always - * return with IRQs enabled. - */ - WARN_ON(irqs_disabled()); - } else - local_irq_enable(); - } - ledtrig_cpu(CPU_LED_IDLE_END); - rcu_idle_exit(); - tick_nohz_idle_exit(); - schedule_preempt_disabled(); - } + +/* + * Called from the core idle loop. + */ +void arch_cpu_idle(void) +{ + if (cpuidle_idle_call()) + default_idle(); } static char reboot_mode = 'h'; @@ -273,11 +225,8 @@ void __show_regs(struct pt_regs *regs) unsigned long flags; char buf[64]; - printk("CPU: %d %s (%s %.*s)\n", - raw_smp_processor_id(), print_tainted(), - init_utsname()->release, - (int)strcspn(init_utsname()->version, " "), - init_utsname()->version); + show_regs_print_info(KERN_DEFAULT); + print_symbol("PC is at %s\n", instruction_pointer(regs)); print_symbol("LR is at %s\n", regs->ARM_lr); printk("pc : [<%08lx>] lr : [<%08lx>] psr: %08lx\n" @@ -332,7 +281,6 @@ void __show_regs(struct pt_regs *regs) void show_regs(struct pt_regs * regs) { printk("\n"); - printk("Pid: %d, comm: %20s\n", task_pid_nr(current), current->comm); __show_regs(regs); dump_stack(); } diff --git a/arch/arm/kernel/smp.c b/arch/arm/kernel/smp.c index 1f2ccccaf009..4619177bcfe6 100644 --- a/arch/arm/kernel/smp.c +++ b/arch/arm/kernel/smp.c @@ -336,7 +336,7 @@ asmlinkage void __cpuinit secondary_start_kernel(void) /* * OK, it's off to the idle thread for us */ - cpu_idle(); + cpu_startup_entry(CPUHP_ONLINE); } void __init smp_cpus_done(unsigned int max_cpus) diff --git a/arch/arm/kernel/topology.c b/arch/arm/kernel/topology.c index 79282ebcd939..f10316b4ecdc 100644 --- a/arch/arm/kernel/topology.c +++ b/arch/arm/kernel/topology.c @@ -100,7 +100,7 @@ static void __init parse_dt_topology(void) int alloc_size, cpu = 0; alloc_size = nr_cpu_ids * sizeof(struct cpu_capacity); - cpu_capacity = (struct cpu_capacity *)kzalloc(alloc_size, GFP_NOWAIT); + cpu_capacity = kzalloc(alloc_size, GFP_NOWAIT); while ((cn = of_find_node_by_type(cn, "cpu"))) { const u32 *rate, *reg; diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index 1c089119b2d7..18b32e8e4497 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -204,13 +204,6 @@ static void dump_backtrace(struct pt_regs *regs, struct task_struct *tsk) } #endif -void dump_stack(void) -{ - dump_backtrace(NULL, NULL); -} - -EXPORT_SYMBOL(dump_stack); - void show_stack(struct task_struct *tsk, unsigned long *sp) { dump_backtrace(NULL, tsk); diff --git a/arch/arm/kvm/arm.c b/arch/arm/kvm/arm.c index c1fe498983ac..842098d78f58 100644 --- a/arch/arm/kvm/arm.c +++ b/arch/arm/kvm/arm.c @@ -614,7 +614,7 @@ static int handle_exit(struct kvm_vcpu *vcpu, struct kvm_run *run, if (hsr_ec >= ARRAY_SIZE(arm_exit_handlers) || !arm_exit_handlers[hsr_ec]) { - kvm_err("Unkown exception class: %#08lx, " + kvm_err("Unknown exception class: %#08lx, " "hsr: %#08x\n", hsr_ec, (unsigned int)vcpu->arch.hsr); BUG(); diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c index b67cd5374117..44199bc2c665 100644 --- a/arch/arm/mach-at91/at91sam9260.c +++ b/arch/arm/mach-at91/at91sam9260.c @@ -232,6 +232,8 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("t2_clk", "fffdc000.timer", &tc5_clk), CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &ohci_clk), CLKDEV_CON_DEV_ID("mci_clk", "fffa8000.mmc", &mmc_clk), + CLKDEV_CON_DEV_ID("spi_clk", "fffc8000.spi", &spi0_clk), + CLKDEV_CON_DEV_ID("spi_clk", "fffcc000.spi", &spi1_clk), /* fake hclk clock */ CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk), CLKDEV_CON_ID("pioA", &pioA_clk), diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c index d3addee43d8d..2ec5efea3f03 100644 --- a/arch/arm/mach-at91/at91sam9g45.c +++ b/arch/arm/mach-at91/at91sam9g45.c @@ -262,6 +262,8 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("mci_clk", "fffd0000.mmc", &mmc1_clk), CLKDEV_CON_DEV_ID(NULL, "fff84000.i2c", &twi0_clk), CLKDEV_CON_DEV_ID(NULL, "fff88000.i2c", &twi1_clk), + CLKDEV_CON_DEV_ID("spi_clk", "fffa4000.spi", &spi0_clk), + CLKDEV_CON_DEV_ID("spi_clk", "fffa8000.spi", &spi1_clk), /* fake hclk clock */ CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &uhphs_clk), CLKDEV_CON_DEV_ID(NULL, "fffff200.gpio", &pioA_clk), diff --git a/arch/arm/mach-at91/at91sam9n12.c b/arch/arm/mach-at91/at91sam9n12.c index 5dfc8fd87103..ccd078355eed 100644 --- a/arch/arm/mach-at91/at91sam9n12.c +++ b/arch/arm/mach-at91/at91sam9n12.c @@ -172,6 +172,8 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma_clk), CLKDEV_CON_DEV_ID(NULL, "f8010000.i2c", &twi0_clk), CLKDEV_CON_DEV_ID(NULL, "f8014000.i2c", &twi1_clk), + CLKDEV_CON_DEV_ID("spi_clk", "f0000000.spi", &spi0_clk), + CLKDEV_CON_DEV_ID("spi_clk", "f0004000.spi", &spi1_clk), CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioAB_clk), CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioAB_clk), CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCD_clk), diff --git a/arch/arm/mach-at91/at91sam9x5.c b/arch/arm/mach-at91/at91sam9x5.c index 44a9a62dcc13..a200d8a17123 100644 --- a/arch/arm/mach-at91/at91sam9x5.c +++ b/arch/arm/mach-at91/at91sam9x5.c @@ -237,6 +237,8 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID(NULL, "f8010000.i2c", &twi0_clk), CLKDEV_CON_DEV_ID(NULL, "f8014000.i2c", &twi1_clk), CLKDEV_CON_DEV_ID(NULL, "f8018000.i2c", &twi2_clk), + CLKDEV_CON_DEV_ID("spi_clk", "f0000000.spi", &spi0_clk), + CLKDEV_CON_DEV_ID("spi_clk", "f0004000.spi", &spi1_clk), CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioAB_clk), CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioAB_clk), CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCD_clk), diff --git a/arch/arm/mach-at91/cpuidle.c b/arch/arm/mach-at91/cpuidle.c index 0c6381516a5a..48f1228c611c 100644 --- a/arch/arm/mach-at91/cpuidle.c +++ b/arch/arm/mach-at91/cpuidle.c @@ -27,8 +27,6 @@ #define AT91_MAX_STATES 2 -static DEFINE_PER_CPU(struct cpuidle_device, at91_cpuidle_device); - /* Actual code that puts the SoC in different idle states */ static int at91_enter_idle(struct cpuidle_device *dev, struct cpuidle_driver *drv, @@ -47,7 +45,6 @@ static int at91_enter_idle(struct cpuidle_device *dev, static struct cpuidle_driver at91_idle_driver = { .name = "at91_idle", .owner = THIS_MODULE, - .en_core_tk_irqen = 1, .states[0] = ARM_CPUIDLE_WFI_STATE, .states[1] = { .enter = at91_enter_idle, @@ -61,20 +58,9 @@ static struct cpuidle_driver at91_idle_driver = { }; /* Initialize CPU idle by registering the idle states */ -static int at91_init_cpuidle(void) +static int __init at91_init_cpuidle(void) { - struct cpuidle_device *device; - - device = &per_cpu(at91_cpuidle_device, smp_processor_id()); - device->state_count = AT91_MAX_STATES; - - cpuidle_register_driver(&at91_idle_driver); - - if (cpuidle_register_device(device)) { - printk(KERN_ERR "at91_init_cpuidle: Failed registering\n"); - return -EIO; - } - return 0; + return cpuidle_register(&at91_idle_driver, NULL); } device_initcall(at91_init_cpuidle); diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig index bf02471d7e7c..f11289519c39 100644 --- a/arch/arm/mach-bcm/Kconfig +++ b/arch/arm/mach-bcm/Kconfig @@ -6,6 +6,7 @@ config ARCH_BCM select ARM_ERRATA_764369 if SMP select ARM_GIC select CPU_V7 + select CLKSRC_OF select GENERIC_CLOCKEVENTS select GENERIC_TIME select GPIO_BCM diff --git a/arch/arm/mach-bcm/board_bcm.c b/arch/arm/mach-bcm/board_bcm.c index f0f9abafad29..259593540477 100644 --- a/arch/arm/mach-bcm/board_bcm.c +++ b/arch/arm/mach-bcm/board_bcm.c @@ -16,14 +16,11 @@ #include <linux/device.h> #include <linux/platform_device.h> #include <linux/irqchip.h> +#include <linux/clocksource.h> #include <asm/mach/arch.h> #include <asm/mach/time.h> -static void timer_init(void) -{ -} - static void __init board_init(void) { @@ -35,7 +32,7 @@ static const char * const bcm11351_dt_compat[] = { "bcm,bcm11351", NULL, }; DT_MACHINE_START(BCM11351_DT, "Broadcom Application Processor") .init_irq = irqchip_init, - .init_time = timer_init, + .init_time = clocksource_of_init, .init_machine = board_init, .dt_compat = bcm11351_dt_compat, MACHINE_END diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile index fb5c1aa98a63..dd1ffccc75e9 100644 --- a/arch/arm/mach-davinci/Makefile +++ b/arch/arm/mach-davinci/Makefile @@ -37,7 +37,6 @@ obj-$(CONFIG_MACH_MITYOMAPL138) += board-mityomapl138.o obj-$(CONFIG_MACH_OMAPL138_HAWKBOARD) += board-omapl138-hawk.o # Power Management -obj-$(CONFIG_CPU_FREQ) += cpufreq.o obj-$(CONFIG_CPU_IDLE) += cpuidle.o obj-$(CONFIG_SUSPEND) += pm.o sleep.o obj-$(CONFIG_HAVE_CLK) += pm_domain.o diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c index 147b8e1a4407..886481c12173 100644 --- a/arch/arm/mach-davinci/board-dm355-evm.c +++ b/arch/arm/mach-davinci/board-dm355-evm.c @@ -242,6 +242,73 @@ static struct vpfe_config vpfe_cfg = { .ccdc = "DM355 CCDC", }; +/* venc standards timings */ +static struct vpbe_enc_mode_info dm355evm_enc_preset_timing[] = { + { + .name = "ntsc", + .timings_type = VPBE_ENC_STD, + .std_id = V4L2_STD_NTSC, + .interlaced = 1, + .xres = 720, + .yres = 480, + .aspect = {11, 10}, + .fps = {30000, 1001}, + .left_margin = 0x79, + .upper_margin = 0x10, + }, + { + .name = "pal", + .timings_type = VPBE_ENC_STD, + .std_id = V4L2_STD_PAL, + .interlaced = 1, + .xres = 720, + .yres = 576, + .aspect = {54, 59}, + .fps = {25, 1}, + .left_margin = 0x7E, + .upper_margin = 0x16 + }, +}; + +#define VENC_STD_ALL (V4L2_STD_NTSC | V4L2_STD_PAL) + +/* + * The outputs available from VPBE + ecnoders. Keep the + * the order same as that of encoders. First those from venc followed by that + * from encoders. Index in the output refers to index on a particular encoder. + * Driver uses this index to pass it to encoder when it supports more than + * one output. Application uses index of the array to set an output. + */ +static struct vpbe_output dm355evm_vpbe_outputs[] = { + { + .output = { + .index = 0, + .name = "Composite", + .type = V4L2_OUTPUT_TYPE_ANALOG, + .std = VENC_STD_ALL, + .capabilities = V4L2_OUT_CAP_STD, + }, + .subdev_name = DM355_VPBE_VENC_SUBDEV_NAME, + .default_mode = "ntsc", + .num_modes = ARRAY_SIZE(dm355evm_enc_preset_timing), + .modes = dm355evm_enc_preset_timing, + .if_params = V4L2_MBUS_FMT_FIXED, + }, +}; + +static struct vpbe_config dm355evm_display_cfg = { + .module_name = "dm355-vpbe-display", + .i2c_adapter_id = 1, + .osd = { + .module_name = DM355_VPBE_OSD_SUBDEV_NAME, + }, + .venc = { + .module_name = DM355_VPBE_VENC_SUBDEV_NAME, + }, + .num_outputs = ARRAY_SIZE(dm355evm_vpbe_outputs), + .outputs = dm355evm_vpbe_outputs, +}; + static struct platform_device *davinci_evm_devices[] __initdata = { &dm355evm_dm9000, &davinci_nand_device, @@ -253,8 +320,6 @@ static struct davinci_uart_config uart_config __initdata = { static void __init dm355_evm_map_io(void) { - /* setup input configuration for VPFE input devices */ - dm355_set_vpfe_config(&vpfe_cfg); dm355_init(); } @@ -344,6 +409,8 @@ static __init void dm355_evm_init(void) davinci_setup_mmc(0, &dm355evm_mmc_config); davinci_setup_mmc(1, &dm355evm_mmc_config); + dm355_init_video(&vpfe_cfg, &dm355evm_display_cfg); + dm355_init_spi0(BIT(0), dm355_evm_spi_info, ARRAY_SIZE(dm355_evm_spi_info)); diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c index c2d4958a0cb6..2a6674356585 100644 --- a/arch/arm/mach-davinci/board-dm365-evm.c +++ b/arch/arm/mach-davinci/board-dm365-evm.c @@ -27,6 +27,7 @@ #include <linux/input.h> #include <linux/spi/spi.h> #include <linux/spi/eeprom.h> +#include <linux/v4l2-dv-timings.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> @@ -39,6 +40,7 @@ #include <linux/platform_data/mtd-davinci.h> #include <linux/platform_data/keyscan-davinci.h> +#include <media/ths7303.h> #include <media/tvp514x.h> #include "davinci.h" @@ -374,6 +376,166 @@ static struct vpfe_config vpfe_cfg = { .ccdc = "ISIF", }; +/* venc standards timings */ +static struct vpbe_enc_mode_info dm365evm_enc_std_timing[] = { + { + .name = "ntsc", + .timings_type = VPBE_ENC_STD, + .std_id = V4L2_STD_NTSC, + .interlaced = 1, + .xres = 720, + .yres = 480, + .aspect = {11, 10}, + .fps = {30000, 1001}, + .left_margin = 0x79, + .upper_margin = 0x10, + }, + { + .name = "pal", + .timings_type = VPBE_ENC_STD, + .std_id = V4L2_STD_PAL, + .interlaced = 1, + .xres = 720, + .yres = 576, + .aspect = {54, 59}, + .fps = {25, 1}, + .left_margin = 0x7E, + .upper_margin = 0x16, + }, +}; + +/* venc dv timings */ +static struct vpbe_enc_mode_info dm365evm_enc_preset_timing[] = { + { + .name = "480p59_94", + .timings_type = VPBE_ENC_DV_TIMINGS, + .dv_timings = V4L2_DV_BT_CEA_720X480P59_94, + .interlaced = 0, + .xres = 720, + .yres = 480, + .aspect = {1, 1}, + .fps = {5994, 100}, + .left_margin = 0x8F, + .upper_margin = 0x2D, + }, + { + .name = "576p50", + .timings_type = VPBE_ENC_DV_TIMINGS, + .dv_timings = V4L2_DV_BT_CEA_720X576P50, + .interlaced = 0, + .xres = 720, + .yres = 576, + .aspect = {1, 1}, + .fps = {50, 1}, + .left_margin = 0x8C, + .upper_margin = 0x36, + }, + { + .name = "720p60", + .timings_type = VPBE_ENC_DV_TIMINGS, + .dv_timings = V4L2_DV_BT_CEA_1280X720P60, + .interlaced = 0, + .xres = 1280, + .yres = 720, + .aspect = {1, 1}, + .fps = {60, 1}, + .left_margin = 0x117, + .right_margin = 70, + .upper_margin = 38, + .lower_margin = 3, + .hsync_len = 80, + .vsync_len = 5, + }, + { + .name = "1080i60", + .timings_type = VPBE_ENC_DV_TIMINGS, + .dv_timings = V4L2_DV_BT_CEA_1920X1080I60, + .interlaced = 1, + .xres = 1920, + .yres = 1080, + .aspect = {1, 1}, + .fps = {30, 1}, + .left_margin = 0xc9, + .right_margin = 80, + .upper_margin = 30, + .lower_margin = 3, + .hsync_len = 88, + .vsync_len = 5, + }, +}; + +#define VENC_STD_ALL (V4L2_STD_NTSC | V4L2_STD_PAL) + +/* + * The outputs available from VPBE + ecnoders. Keep the + * the order same as that of encoders. First those from venc followed by that + * from encoders. Index in the output refers to index on a particular + * encoder.Driver uses this index to pass it to encoder when it supports more + * than one output. Application uses index of the array to set an output. + */ +static struct vpbe_output dm365evm_vpbe_outputs[] = { + { + .output = { + .index = 0, + .name = "Composite", + .type = V4L2_OUTPUT_TYPE_ANALOG, + .std = VENC_STD_ALL, + .capabilities = V4L2_OUT_CAP_STD, + }, + .subdev_name = DM365_VPBE_VENC_SUBDEV_NAME, + .default_mode = "ntsc", + .num_modes = ARRAY_SIZE(dm365evm_enc_std_timing), + .modes = dm365evm_enc_std_timing, + .if_params = V4L2_MBUS_FMT_FIXED, + }, + { + .output = { + .index = 1, + .name = "Component", + .type = V4L2_OUTPUT_TYPE_ANALOG, + .capabilities = V4L2_OUT_CAP_DV_TIMINGS, + }, + .subdev_name = DM365_VPBE_VENC_SUBDEV_NAME, + .default_mode = "480p59_94", + .num_modes = ARRAY_SIZE(dm365evm_enc_preset_timing), + .modes = dm365evm_enc_preset_timing, + .if_params = V4L2_MBUS_FMT_FIXED, + }, +}; + +/* + * Amplifiers on the board + */ +struct ths7303_platform_data ths7303_pdata = { + .ch_1 = 3, + .ch_2 = 3, + .ch_3 = 3, + .init_enable = 1, +}; + +static struct amp_config_info vpbe_amp = { + .module_name = "ths7303", + .is_i2c = 1, + .board_info = { + I2C_BOARD_INFO("ths7303", 0x2c), + .platform_data = &ths7303_pdata, + } +}; + +static struct vpbe_config dm365evm_display_cfg = { + .module_name = "dm365-vpbe-display", + .i2c_adapter_id = 1, + .amp = &vpbe_amp, + .osd = { + .module_name = DM365_VPBE_OSD_SUBDEV_NAME, + }, + .venc = { + .module_name = DM365_VPBE_VENC_SUBDEV_NAME, + }, + .num_outputs = ARRAY_SIZE(dm365evm_vpbe_outputs), + .outputs = dm365evm_vpbe_outputs, +}; + static void __init evm_init_i2c(void) { davinci_init_i2c(&i2c_pdata); @@ -564,8 +726,6 @@ static struct davinci_uart_config uart_config __initdata = { static void __init dm365_evm_map_io(void) { - /* setup input configuration for VPFE input devices */ - dm365_set_vpfe_config(&vpfe_cfg); dm365_init(); } @@ -597,6 +757,8 @@ static __init void dm365_evm_init(void) davinci_setup_mmc(0, &dm365evm_mmc_config); + dm365_init_video(&vpfe_cfg, &dm365evm_display_cfg); + /* maybe setup mmc1/etc ... _after_ mmc0 */ evm_init_cpld(); diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c index 71735e7797cc..745280d4144c 100644 --- a/arch/arm/mach-davinci/board-dm644x-evm.c +++ b/arch/arm/mach-davinci/board-dm644x-evm.c @@ -622,7 +622,7 @@ static struct vpbe_enc_mode_info dm644xevm_enc_std_timing[] = { { .name = "ntsc", .timings_type = VPBE_ENC_STD, - .std_id = V4L2_STD_525_60, + .std_id = V4L2_STD_NTSC, .interlaced = 1, .xres = 720, .yres = 480, @@ -634,7 +634,7 @@ static struct vpbe_enc_mode_info dm644xevm_enc_std_timing[] = { { .name = "pal", .timings_type = VPBE_ENC_STD, - .std_id = V4L2_STD_625_50, + .std_id = V4L2_STD_PAL, .interlaced = 1, .xres = 720, .yres = 576, @@ -649,7 +649,7 @@ static struct vpbe_enc_mode_info dm644xevm_enc_std_timing[] = { static struct vpbe_enc_mode_info dm644xevm_enc_preset_timing[] = { { .name = "480p59_94", - .timings_type = VPBE_ENC_CUSTOM_TIMINGS, + .timings_type = VPBE_ENC_DV_TIMINGS, .dv_timings = V4L2_DV_BT_CEA_720X480P59_94, .interlaced = 0, .xres = 720, @@ -661,7 +661,7 @@ static struct vpbe_enc_mode_info dm644xevm_enc_preset_timing[] = { }, { .name = "576p50", - .timings_type = VPBE_ENC_CUSTOM_TIMINGS, + .timings_type = VPBE_ENC_DV_TIMINGS, .dv_timings = V4L2_DV_BT_CEA_720X576P50, .interlaced = 0, .xres = 720, diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c index de7adff324dc..fc4871ac1c2c 100644 --- a/arch/arm/mach-davinci/board-dm646x-evm.c +++ b/arch/arm/mach-davinci/board-dm646x-evm.c @@ -514,7 +514,7 @@ static const struct vpif_output dm6467_ch0_outputs[] = { .index = 1, .name = "Component", .type = V4L2_OUTPUT_TYPE_ANALOG, - .capabilities = V4L2_OUT_CAP_CUSTOM_TIMINGS, + .capabilities = V4L2_OUT_CAP_DV_TIMINGS, }, .subdev_name = "adv7343", .output_route = ADV7343_COMPONENT_ID, diff --git a/arch/arm/mach-davinci/cpufreq.c b/arch/arm/mach-davinci/cpufreq.c deleted file mode 100644 index 4729eaab0f40..000000000000 --- a/arch/arm/mach-davinci/cpufreq.c +++ /dev/null @@ -1,248 +0,0 @@ -/* - * CPU frequency scaling for DaVinci - * - * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/ - * - * Based on linux/arch/arm/plat-omap/cpu-omap.c. Original Copyright follows: - * - * Copyright (C) 2005 Nokia Corporation - * Written by Tony Lindgren <tony@atomide.com> - * - * Based on cpu-sa1110.c, Copyright (C) 2001 Russell King - * - * Copyright (C) 2007-2008 Texas Instruments, Inc. - * Updated to support OMAP3 - * Rajendra Nayak <rnayak@ti.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#include <linux/types.h> -#include <linux/cpufreq.h> -#include <linux/init.h> -#include <linux/err.h> -#include <linux/clk.h> -#include <linux/platform_device.h> -#include <linux/export.h> - -#include <mach/hardware.h> -#include <mach/cpufreq.h> -#include <mach/common.h> - -#include "clock.h" - -struct davinci_cpufreq { - struct device *dev; - struct clk *armclk; - struct clk *asyncclk; - unsigned long asyncrate; -}; -static struct davinci_cpufreq cpufreq; - -static int davinci_verify_speed(struct cpufreq_policy *policy) -{ - struct davinci_cpufreq_config *pdata = cpufreq.dev->platform_data; - struct cpufreq_frequency_table *freq_table = pdata->freq_table; - struct clk *armclk = cpufreq.armclk; - - if (freq_table) - return cpufreq_frequency_table_verify(policy, freq_table); - - if (policy->cpu) - return -EINVAL; - - cpufreq_verify_within_limits(policy, policy->cpuinfo.min_freq, - policy->cpuinfo.max_freq); - - policy->min = clk_round_rate(armclk, policy->min * 1000) / 1000; - policy->max = clk_round_rate(armclk, policy->max * 1000) / 1000; - cpufreq_verify_within_limits(policy, policy->cpuinfo.min_freq, - policy->cpuinfo.max_freq); - return 0; -} - -static unsigned int davinci_getspeed(unsigned int cpu) -{ - if (cpu) - return 0; - - return clk_get_rate(cpufreq.armclk) / 1000; -} - -static int davinci_target(struct cpufreq_policy *policy, - unsigned int target_freq, unsigned int relation) -{ - int ret = 0; - unsigned int idx; - struct cpufreq_freqs freqs; - struct davinci_cpufreq_config *pdata = cpufreq.dev->platform_data; - struct clk *armclk = cpufreq.armclk; - - /* - * Ensure desired rate is within allowed range. Some govenors - * (ondemand) will just pass target_freq=0 to get the minimum. - */ - if (target_freq < policy->cpuinfo.min_freq) - target_freq = policy->cpuinfo.min_freq; - if (target_freq > policy->cpuinfo.max_freq) - target_freq = policy->cpuinfo.max_freq; - - freqs.old = davinci_getspeed(0); - freqs.new = clk_round_rate(armclk, target_freq * 1000) / 1000; - freqs.cpu = 0; - - if (freqs.old == freqs.new) - return ret; - - dev_dbg(cpufreq.dev, "transition: %u --> %u\n", freqs.old, freqs.new); - - ret = cpufreq_frequency_table_target(policy, pdata->freq_table, - freqs.new, relation, &idx); - if (ret) - return -EINVAL; - - cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); - - /* if moving to higher frequency, up the voltage beforehand */ - if (pdata->set_voltage && freqs.new > freqs.old) { - ret = pdata->set_voltage(idx); - if (ret) - goto out; - } - - ret = clk_set_rate(armclk, idx); - if (ret) - goto out; - - if (cpufreq.asyncclk) { - ret = clk_set_rate(cpufreq.asyncclk, cpufreq.asyncrate); - if (ret) - goto out; - } - - /* if moving to lower freq, lower the voltage after lowering freq */ - if (pdata->set_voltage && freqs.new < freqs.old) - pdata->set_voltage(idx); - -out: - cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); - - return ret; -} - -static int davinci_cpu_init(struct cpufreq_policy *policy) -{ - int result = 0; - struct davinci_cpufreq_config *pdata = cpufreq.dev->platform_data; - struct cpufreq_frequency_table *freq_table = pdata->freq_table; - - if (policy->cpu != 0) - return -EINVAL; - - /* Finish platform specific initialization */ - if (pdata->init) { - result = pdata->init(); - if (result) - return result; - } - - policy->cur = policy->min = policy->max = davinci_getspeed(0); - - if (freq_table) { - result = cpufreq_frequency_table_cpuinfo(policy, freq_table); - if (!result) - cpufreq_frequency_table_get_attr(freq_table, - policy->cpu); - } else { - policy->cpuinfo.min_freq = policy->min; - policy->cpuinfo.max_freq = policy->max; - } - - policy->min = policy->cpuinfo.min_freq; - policy->max = policy->cpuinfo.max_freq; - policy->cur = davinci_getspeed(0); - - /* - * Time measurement across the target() function yields ~1500-1800us - * time taken with no drivers on notification list. - * Setting the latency to 2000 us to accommodate addition of drivers - * to pre/post change notification list. - */ - policy->cpuinfo.transition_latency = 2000 * 1000; - return 0; -} - -static int davinci_cpu_exit(struct cpufreq_policy *policy) -{ - cpufreq_frequency_table_put_attr(policy->cpu); - return 0; -} - -static struct freq_attr *davinci_cpufreq_attr[] = { - &cpufreq_freq_attr_scaling_available_freqs, - NULL, -}; - -static struct cpufreq_driver davinci_driver = { - .flags = CPUFREQ_STICKY, - .verify = davinci_verify_speed, - .target = davinci_target, - .get = davinci_getspeed, - .init = davinci_cpu_init, - .exit = davinci_cpu_exit, - .name = "davinci", - .attr = davinci_cpufreq_attr, -}; - -static int __init davinci_cpufreq_probe(struct platform_device *pdev) -{ - struct davinci_cpufreq_config *pdata = pdev->dev.platform_data; - struct clk *asyncclk; - - if (!pdata) - return -EINVAL; - if (!pdata->freq_table) - return -EINVAL; - - cpufreq.dev = &pdev->dev; - - cpufreq.armclk = clk_get(NULL, "arm"); - if (IS_ERR(cpufreq.armclk)) { - dev_err(cpufreq.dev, "Unable to get ARM clock\n"); - return PTR_ERR(cpufreq.armclk); - } - - asyncclk = clk_get(cpufreq.dev, "async"); - if (!IS_ERR(asyncclk)) { - cpufreq.asyncclk = asyncclk; - cpufreq.asyncrate = clk_get_rate(asyncclk); - } - - return cpufreq_register_driver(&davinci_driver); -} - -static int __exit davinci_cpufreq_remove(struct platform_device *pdev) -{ - clk_put(cpufreq.armclk); - - if (cpufreq.asyncclk) - clk_put(cpufreq.asyncclk); - - return cpufreq_unregister_driver(&davinci_driver); -} - -static struct platform_driver davinci_cpufreq_driver = { - .driver = { - .name = "cpufreq-davinci", - .owner = THIS_MODULE, - }, - .remove = __exit_p(davinci_cpufreq_remove), -}; - -int __init davinci_cpufreq_init(void) -{ - return platform_driver_probe(&davinci_cpufreq_driver, - davinci_cpufreq_probe); -} - diff --git a/arch/arm/mach-davinci/cpuidle.c b/arch/arm/mach-davinci/cpuidle.c index 5ac9e9384b15..36aef3a7dedb 100644 --- a/arch/arm/mach-davinci/cpuidle.c +++ b/arch/arm/mach-davinci/cpuidle.c @@ -25,7 +25,6 @@ #define DAVINCI_CPUIDLE_MAX_STATES 2 -static DEFINE_PER_CPU(struct cpuidle_device, davinci_cpuidle_device); static void __iomem *ddr2_reg_base; static bool ddr2_pdown; @@ -50,14 +49,10 @@ static void davinci_save_ddr_power(int enter, bool pdown) /* Actual code that puts the SoC in different idle states */ static int davinci_enter_idle(struct cpuidle_device *dev, - struct cpuidle_driver *drv, - int index) + struct cpuidle_driver *drv, int index) { davinci_save_ddr_power(1, ddr2_pdown); - - index = cpuidle_wrap_enter(dev, drv, index, - arm_cpuidle_simple_enter); - + cpu_do_idle(); davinci_save_ddr_power(0, ddr2_pdown); return index; @@ -66,7 +61,6 @@ static int davinci_enter_idle(struct cpuidle_device *dev, static struct cpuidle_driver davinci_idle_driver = { .name = "cpuidle-davinci", .owner = THIS_MODULE, - .en_core_tk_irqen = 1, .states[0] = ARM_CPUIDLE_WFI_STATE, .states[1] = { .enter = davinci_enter_idle, @@ -81,12 +75,8 @@ static struct cpuidle_driver davinci_idle_driver = { static int __init davinci_cpuidle_probe(struct platform_device *pdev) { - int ret; - struct cpuidle_device *device; struct davinci_cpuidle_config *pdata = pdev->dev.platform_data; - device = &per_cpu(davinci_cpuidle_device, smp_processor_id()); - if (!pdata) { dev_err(&pdev->dev, "cannot get platform data\n"); return -ENOENT; @@ -96,20 +86,7 @@ static int __init davinci_cpuidle_probe(struct platform_device *pdev) ddr2_pdown = pdata->ddr2_pdown; - ret = cpuidle_register_driver(&davinci_idle_driver); - if (ret) { - dev_err(&pdev->dev, "failed to register driver\n"); - return ret; - } - - ret = cpuidle_register_device(device); - if (ret) { - dev_err(&pdev->dev, "failed to register device\n"); - cpuidle_unregister_driver(&davinci_idle_driver); - return ret; - } - - return 0; + return cpuidle_register(&davinci_idle_driver, NULL); } static struct platform_driver davinci_cpuidle_driver = { diff --git a/arch/arm/mach-davinci/davinci.h b/arch/arm/mach-davinci/davinci.h index 12d544befcfa..1ab3df423dac 100644 --- a/arch/arm/mach-davinci/davinci.h +++ b/arch/arm/mach-davinci/davinci.h @@ -36,12 +36,19 @@ #include <media/davinci/vpbe_osd.h> #define DAVINCI_SYSTEM_MODULE_BASE 0x01c40000 +#define SYSMOD_VDAC_CONFIG 0x2c #define SYSMOD_VIDCLKCTL 0x38 #define SYSMOD_VPSS_CLKCTL 0x44 #define SYSMOD_VDD3P3VPWDN 0x48 #define SYSMOD_VSCLKDIS 0x6c #define SYSMOD_PUPDCTL1 0x7c +/* VPSS CLKCTL bit definitions */ +#define VPSS_MUXSEL_EXTCLK_ENABLE BIT(1) +#define VPSS_VENCCLKEN_ENABLE BIT(3) +#define VPSS_DACCLKEN_ENABLE BIT(4) +#define VPSS_PLLC2SYSCLK5_ENABLE BIT(5) + extern void __iomem *davinci_sysmod_base; #define DAVINCI_SYSMOD_VIRT(x) (davinci_sysmod_base + (x)) void davinci_map_sysmod(void); @@ -74,7 +81,7 @@ void __init dm355_init(void); void dm355_init_spi0(unsigned chipselect_mask, const struct spi_board_info *info, unsigned len); void __init dm355_init_asp1(u32 evt_enable, struct snd_platform_data *pdata); -void dm355_set_vpfe_config(struct vpfe_config *cfg); +int dm355_init_video(struct vpfe_config *, struct vpbe_config *); /* DM365 function declarations */ void __init dm365_init(void); @@ -84,7 +91,7 @@ void __init dm365_init_ks(struct davinci_ks_platform_data *pdata); void __init dm365_init_rtc(void); void dm365_init_spi0(unsigned chipselect_mask, const struct spi_board_info *info, unsigned len); -void dm365_set_vpfe_config(struct vpfe_config *cfg); +int dm365_init_video(struct vpfe_config *, struct vpbe_config *); /* DM644x function declarations */ void __init dm644x_init(void); diff --git a/arch/arm/mach-davinci/dm355.c b/arch/arm/mach-davinci/dm355.c index b49c3b77d55e..bf9a9d4ad9f5 100644 --- a/arch/arm/mach-davinci/dm355.c +++ b/arch/arm/mach-davinci/dm355.c @@ -35,6 +35,8 @@ #include "asp.h" #define DM355_UART2_BASE (IO_PHYS + 0x206000) +#define DM355_OSD_BASE (IO_PHYS + 0x70200) +#define DM355_VENC_BASE (IO_PHYS + 0x70400) /* * Device specific clocks @@ -345,8 +347,8 @@ static struct clk_lookup dm355_clks[] = { CLK(NULL, "pll1_aux", &pll1_aux_clk), CLK(NULL, "pll1_sysclkbp", &pll1_sysclkbp), CLK(NULL, "vpss_dac", &vpss_dac_clk), - CLK(NULL, "vpss_master", &vpss_master_clk), - CLK(NULL, "vpss_slave", &vpss_slave_clk), + CLK("vpss", "master", &vpss_master_clk), + CLK("vpss", "slave", &vpss_slave_clk), CLK(NULL, "clkout1", &clkout1_clk), CLK(NULL, "clkout2", &clkout2_clk), CLK(NULL, "pll2", &pll2_clk), @@ -744,11 +746,146 @@ static struct platform_device vpfe_capture_dev = { }, }; -void dm355_set_vpfe_config(struct vpfe_config *cfg) +static struct resource dm355_osd_resources[] = { + { + .start = DM355_OSD_BASE, + .end = DM355_OSD_BASE + 0x17f, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device dm355_osd_dev = { + .name = DM355_VPBE_OSD_SUBDEV_NAME, + .id = -1, + .num_resources = ARRAY_SIZE(dm355_osd_resources), + .resource = dm355_osd_resources, + .dev = { + .dma_mask = &vpfe_capture_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, +}; + +static struct resource dm355_venc_resources[] = { + { + .start = IRQ_VENCINT, + .end = IRQ_VENCINT, + .flags = IORESOURCE_IRQ, + }, + /* venc registers io space */ + { + .start = DM355_VENC_BASE, + .end = DM355_VENC_BASE + 0x17f, + .flags = IORESOURCE_MEM, + }, + /* VDAC config register io space */ + { + .start = DAVINCI_SYSTEM_MODULE_BASE + SYSMOD_VDAC_CONFIG, + .end = DAVINCI_SYSTEM_MODULE_BASE + SYSMOD_VDAC_CONFIG + 3, + .flags = IORESOURCE_MEM, + }, +}; + +static struct resource dm355_v4l2_disp_resources[] = { + { + .start = IRQ_VENCINT, + .end = IRQ_VENCINT, + .flags = IORESOURCE_IRQ, + }, + /* venc registers io space */ + { + .start = DM355_VENC_BASE, + .end = DM355_VENC_BASE + 0x17f, + .flags = IORESOURCE_MEM, + }, +}; + +static int dm355_vpbe_setup_pinmux(enum v4l2_mbus_pixelcode if_type, + int field) +{ + switch (if_type) { + case V4L2_MBUS_FMT_SGRBG8_1X8: + davinci_cfg_reg(DM355_VOUT_FIELD_G70); + break; + case V4L2_MBUS_FMT_YUYV10_1X20: + if (field) + davinci_cfg_reg(DM355_VOUT_FIELD); + else + davinci_cfg_reg(DM355_VOUT_FIELD_G70); + break; + default: + return -EINVAL; + } + + davinci_cfg_reg(DM355_VOUT_COUTL_EN); + davinci_cfg_reg(DM355_VOUT_COUTH_EN); + + return 0; +} + +static int dm355_venc_setup_clock(enum vpbe_enc_timings_type type, + unsigned int pclock) { - vpfe_capture_dev.dev.platform_data = cfg; + void __iomem *vpss_clk_ctrl_reg; + + vpss_clk_ctrl_reg = DAVINCI_SYSMOD_VIRT(SYSMOD_VPSS_CLKCTL); + + switch (type) { + case VPBE_ENC_STD: + writel(VPSS_DACCLKEN_ENABLE | VPSS_VENCCLKEN_ENABLE, + vpss_clk_ctrl_reg); + break; + case VPBE_ENC_DV_TIMINGS: + if (pclock > 27000000) + /* + * For HD, use external clock source since we cannot + * support HD mode with internal clocks. + */ + writel(VPSS_MUXSEL_EXTCLK_ENABLE, vpss_clk_ctrl_reg); + break; + default: + return -EINVAL; + } + + return 0; } +static struct platform_device dm355_vpbe_display = { + .name = "vpbe-v4l2", + .id = -1, + .num_resources = ARRAY_SIZE(dm355_v4l2_disp_resources), + .resource = dm355_v4l2_disp_resources, + .dev = { + .dma_mask = &vpfe_capture_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, +}; + +struct venc_platform_data dm355_venc_pdata = { + .setup_pinmux = dm355_vpbe_setup_pinmux, + .setup_clock = dm355_venc_setup_clock, +}; + +static struct platform_device dm355_venc_dev = { + .name = DM355_VPBE_VENC_SUBDEV_NAME, + .id = -1, + .num_resources = ARRAY_SIZE(dm355_venc_resources), + .resource = dm355_venc_resources, + .dev = { + .dma_mask = &vpfe_capture_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = (void *)&dm355_venc_pdata, + }, +}; + +static struct platform_device dm355_vpbe_dev = { + .name = "vpbe_controller", + .id = -1, + .dev = { + .dma_mask = &vpfe_capture_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, +}; + /*----------------------------------------------------------------------*/ static struct map_desc dm355_io_desc[] = { @@ -868,19 +1005,36 @@ void __init dm355_init(void) davinci_map_sysmod(); } +int __init dm355_init_video(struct vpfe_config *vpfe_cfg, + struct vpbe_config *vpbe_cfg) +{ + if (vpfe_cfg || vpbe_cfg) + platform_device_register(&dm355_vpss_device); + + if (vpfe_cfg) { + vpfe_capture_dev.dev.platform_data = vpfe_cfg; + platform_device_register(&dm355_ccdc_dev); + platform_device_register(&vpfe_capture_dev); + } + + if (vpbe_cfg) { + dm355_vpbe_dev.dev.platform_data = vpbe_cfg; + platform_device_register(&dm355_osd_dev); + platform_device_register(&dm355_venc_dev); + platform_device_register(&dm355_vpbe_dev); + platform_device_register(&dm355_vpbe_display); + } + + return 0; +} + static int __init dm355_init_devices(void) { if (!cpu_is_davinci_dm355()) return 0; - /* Add ccdc clock aliases */ - clk_add_alias("master", dm355_ccdc_dev.name, "vpss_master", NULL); - clk_add_alias("slave", dm355_ccdc_dev.name, "vpss_master", NULL); davinci_cfg_reg(DM355_INT_EDMA_CC); platform_device_register(&dm355_edma_device); - platform_device_register(&dm355_vpss_device); - platform_device_register(&dm355_ccdc_dev); - platform_device_register(&vpfe_capture_dev); return 0; } diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c index 6c3980540be0..ff771ceac3f1 100644 --- a/arch/arm/mach-davinci/dm365.c +++ b/arch/arm/mach-davinci/dm365.c @@ -39,16 +39,13 @@ #include "asp.h" #define DM365_REF_FREQ 24000000 /* 24 MHz on the DM365 EVM */ - -/* Base of key scan register bank */ -#define DM365_KEYSCAN_BASE 0x01c69400 - #define DM365_RTC_BASE 0x01c69000 - +#define DM365_KEYSCAN_BASE 0x01c69400 +#define DM365_OSD_BASE 0x01c71c00 +#define DM365_VENC_BASE 0x01c71e00 #define DAVINCI_DM365_VC_BASE 0x01d0c000 #define DAVINCI_DMA_VC_TX 2 #define DAVINCI_DMA_VC_RX 3 - #define DM365_EMAC_BASE 0x01d07000 #define DM365_EMAC_MDIO_BASE (DM365_EMAC_BASE + 0x4000) #define DM365_EMAC_CNTRL_OFFSET 0x0000 @@ -257,6 +254,12 @@ static struct clk vpss_master_clk = { .flags = CLK_PSC, }; +static struct clk vpss_slave_clk = { + .name = "vpss_slave", + .parent = &pll1_sysclk5, + .lpsc = DAVINCI_LPSC_VPSSSLV, +}; + static struct clk arm_clk = { .name = "arm_clk", .parent = &pll2_sysclk2, @@ -449,7 +452,8 @@ static struct clk_lookup dm365_clks[] = { CLK(NULL, "pll2_sysclk8", &pll2_sysclk8), CLK(NULL, "pll2_sysclk9", &pll2_sysclk9), CLK(NULL, "vpss_dac", &vpss_dac_clk), - CLK(NULL, "vpss_master", &vpss_master_clk), + CLK("vpss", "master", &vpss_master_clk), + CLK("vpss", "slave", &vpss_slave_clk), CLK(NULL, "arm", &arm_clk), CLK(NULL, "uart0", &uart0_clk), CLK(NULL, "uart1", &uart1_clk), @@ -1226,6 +1230,173 @@ static struct platform_device dm365_isif_dev = { }, }; +static struct resource dm365_osd_resources[] = { + { + .start = DM365_OSD_BASE, + .end = DM365_OSD_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, +}; + +static u64 dm365_video_dma_mask = DMA_BIT_MASK(32); + +static struct platform_device dm365_osd_dev = { + .name = DM365_VPBE_OSD_SUBDEV_NAME, + .id = -1, + .num_resources = ARRAY_SIZE(dm365_osd_resources), + .resource = dm365_osd_resources, + .dev = { + .dma_mask = &dm365_video_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, +}; + +static struct resource dm365_venc_resources[] = { + { + .start = IRQ_VENCINT, + .end = IRQ_VENCINT, + .flags = IORESOURCE_IRQ, + }, + /* venc registers io space */ + { + .start = DM365_VENC_BASE, + .end = DM365_VENC_BASE + 0x177, + .flags = IORESOURCE_MEM, + }, + /* vdaccfg registers io space */ + { + .start = DAVINCI_SYSTEM_MODULE_BASE + SYSMOD_VDAC_CONFIG, + .end = DAVINCI_SYSTEM_MODULE_BASE + SYSMOD_VDAC_CONFIG + 3, + .flags = IORESOURCE_MEM, + }, +}; + +static struct resource dm365_v4l2_disp_resources[] = { + { + .start = IRQ_VENCINT, + .end = IRQ_VENCINT, + .flags = IORESOURCE_IRQ, + }, + /* venc registers io space */ + { + .start = DM365_VENC_BASE, + .end = DM365_VENC_BASE + 0x177, + .flags = IORESOURCE_MEM, + }, +}; + +static int dm365_vpbe_setup_pinmux(enum v4l2_mbus_pixelcode if_type, + int field) +{ + switch (if_type) { + case V4L2_MBUS_FMT_SGRBG8_1X8: + davinci_cfg_reg(DM365_VOUT_FIELD_G81); + davinci_cfg_reg(DM365_VOUT_COUTL_EN); + davinci_cfg_reg(DM365_VOUT_COUTH_EN); + break; + case V4L2_MBUS_FMT_YUYV10_1X20: + if (field) + davinci_cfg_reg(DM365_VOUT_FIELD); + else + davinci_cfg_reg(DM365_VOUT_FIELD_G81); + davinci_cfg_reg(DM365_VOUT_COUTL_EN); + davinci_cfg_reg(DM365_VOUT_COUTH_EN); + break; + default: + return -EINVAL; + } + + return 0; +} + +static int dm365_venc_setup_clock(enum vpbe_enc_timings_type type, + unsigned int pclock) +{ + void __iomem *vpss_clkctl_reg; + u32 val; + + vpss_clkctl_reg = DAVINCI_SYSMOD_VIRT(SYSMOD_VPSS_CLKCTL); + + switch (type) { + case VPBE_ENC_STD: + val = VPSS_VENCCLKEN_ENABLE | VPSS_DACCLKEN_ENABLE; + break; + case VPBE_ENC_DV_TIMINGS: + if (pclock <= 27000000) { + val = VPSS_VENCCLKEN_ENABLE | VPSS_DACCLKEN_ENABLE; + } else { + /* set sysclk4 to output 74.25 MHz from pll1 */ + val = VPSS_PLLC2SYSCLK5_ENABLE | VPSS_DACCLKEN_ENABLE | + VPSS_VENCCLKEN_ENABLE; + } + break; + default: + return -EINVAL; + } + writel(val, vpss_clkctl_reg); + + return 0; +} + +static struct platform_device dm365_vpbe_display = { + .name = "vpbe-v4l2", + .id = -1, + .num_resources = ARRAY_SIZE(dm365_v4l2_disp_resources), + .resource = dm365_v4l2_disp_resources, + .dev = { + .dma_mask = &dm365_video_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, +}; + +struct venc_platform_data dm365_venc_pdata = { + .setup_pinmux = dm365_vpbe_setup_pinmux, + .setup_clock = dm365_venc_setup_clock, +}; + +static struct platform_device dm365_venc_dev = { + .name = DM365_VPBE_VENC_SUBDEV_NAME, + .id = -1, + .num_resources = ARRAY_SIZE(dm365_venc_resources), + .resource = dm365_venc_resources, + .dev = { + .dma_mask = &dm365_video_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = (void *)&dm365_venc_pdata, + }, +}; + +static struct platform_device dm365_vpbe_dev = { + .name = "vpbe_controller", + .id = -1, + .dev = { + .dma_mask = &dm365_video_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, +}; + +int __init dm365_init_video(struct vpfe_config *vpfe_cfg, + struct vpbe_config *vpbe_cfg) +{ + if (vpfe_cfg || vpbe_cfg) + platform_device_register(&dm365_vpss_device); + + if (vpfe_cfg) { + vpfe_capture_dev.dev.platform_data = vpfe_cfg; + platform_device_register(&dm365_isif_dev); + platform_device_register(&vpfe_capture_dev); + } + if (vpbe_cfg) { + dm365_vpbe_dev.dev.platform_data = vpbe_cfg; + platform_device_register(&dm365_osd_dev); + platform_device_register(&dm365_venc_dev); + platform_device_register(&dm365_vpbe_dev); + platform_device_register(&dm365_vpbe_display); + } + + return 0; +} + static int __init dm365_init_devices(void) { if (!cpu_is_davinci_dm365()) @@ -1239,16 +1410,6 @@ static int __init dm365_init_devices(void) clk_add_alias(NULL, dev_name(&dm365_mdio_device.dev), NULL, &dm365_emac_device.dev); - /* Add isif clock alias */ - clk_add_alias("master", dm365_isif_dev.name, "vpss_master", NULL); - platform_device_register(&dm365_vpss_device); - platform_device_register(&dm365_isif_dev); - platform_device_register(&vpfe_capture_dev); return 0; } postcore_initcall(dm365_init_devices); - -void dm365_set_vpfe_config(struct vpfe_config *cfg) -{ - vpfe_capture_dev.dev.platform_data = cfg; -} diff --git a/arch/arm/mach-davinci/dm644x.c b/arch/arm/mach-davinci/dm644x.c index db1dd92e00af..c2a9273330bf 100644 --- a/arch/arm/mach-davinci/dm644x.c +++ b/arch/arm/mach-davinci/dm644x.c @@ -300,8 +300,8 @@ static struct clk_lookup dm644x_clks[] = { CLK(NULL, "dsp", &dsp_clk), CLK(NULL, "arm", &arm_clk), CLK(NULL, "vicp", &vicp_clk), - CLK(NULL, "vpss_master", &vpss_master_clk), - CLK(NULL, "vpss_slave", &vpss_slave_clk), + CLK("vpss", "master", &vpss_master_clk), + CLK("vpss", "slave", &vpss_slave_clk), CLK(NULL, "arm", &arm_clk), CLK(NULL, "uart0", &uart0_clk), CLK(NULL, "uart1", &uart1_clk), @@ -706,7 +706,7 @@ static int dm644x_venc_setup_clock(enum vpbe_enc_timings_type type, v |= DM644X_VPSS_DACCLKEN; writel(v, DAVINCI_SYSMOD_VIRT(SYSMOD_VPSS_CLKCTL)); break; - case VPBE_ENC_CUSTOM_TIMINGS: + case VPBE_ENC_DV_TIMINGS: if (pclock <= 27000000) { v |= DM644X_VPSS_DACCLKEN; writel(v, DAVINCI_SYSMOD_VIRT(SYSMOD_VPSS_CLKCTL)); @@ -901,11 +901,6 @@ int __init dm644x_init_video(struct vpfe_config *vpfe_cfg, dm644x_vpfe_dev.dev.platform_data = vpfe_cfg; platform_device_register(&dm644x_ccdc_dev); platform_device_register(&dm644x_vpfe_dev); - /* Add ccdc clock aliases */ - clk_add_alias("master", dm644x_ccdc_dev.name, - "vpss_master", NULL); - clk_add_alias("slave", dm644x_ccdc_dev.name, - "vpss_slave", NULL); } if (vpbe_cfg) { diff --git a/arch/arm/mach-davinci/pm_domain.c b/arch/arm/mach-davinci/pm_domain.c index c90250e3bef8..6b98413cebd6 100644 --- a/arch/arm/mach-davinci/pm_domain.c +++ b/arch/arm/mach-davinci/pm_domain.c @@ -53,7 +53,7 @@ static struct dev_pm_domain davinci_pm_domain = { static struct pm_clk_notifier_block platform_bus_notifier = { .pm_domain = &davinci_pm_domain, - .con_ids = { "fck", NULL, }, + .con_ids = { "fck", "master", "slave", NULL }, }; static int __init davinci_pm_runtime_init(void) diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index 70f94c87479d..d5dde0727339 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -72,10 +72,12 @@ config SOC_EXYNOS5440 bool "SAMSUNG EXYNOS5440" default y depends on ARCH_EXYNOS5 + select ARCH_HAS_OPP select ARM_ARCH_TIMER select AUTO_ZRELADDR select PINCTRL select PINCTRL_EXYNOS5440 + select PM_OPP help Enable EXYNOS5440 SoC support diff --git a/arch/arm/mach-exynos/cpuidle.c b/arch/arm/mach-exynos/cpuidle.c index fcfe0251aa3e..498a7a23e260 100644 --- a/arch/arm/mach-exynos/cpuidle.c +++ b/arch/arm/mach-exynos/cpuidle.c @@ -58,7 +58,6 @@ static DEFINE_PER_CPU(struct cpuidle_device, exynos4_cpuidle_device); static struct cpuidle_driver exynos4_idle_driver = { .name = "exynos4_idle", .owner = THIS_MODULE, - .en_core_tk_irqen = 1, }; /* Ext-GIC nIRQ/nFIQ is the only wakeup source in AFTR */ diff --git a/arch/arm/mach-exynos/mach-universal_c210.c b/arch/arm/mach-exynos/mach-universal_c210.c index 497fcb793dc1..d28c7fbaba2d 100644 --- a/arch/arm/mach-exynos/mach-universal_c210.c +++ b/arch/arm/mach-exynos/mach-universal_c210.c @@ -97,6 +97,19 @@ static struct s3c2410_uartcfg universal_uartcfgs[] __initdata = { static struct regulator_consumer_supply max8952_consumer = REGULATOR_SUPPLY("vdd_arm", NULL); +static struct regulator_init_data universal_max8952_reg_data = { + .constraints = { + .name = "VARM_1.2V", + .min_uV = 770000, + .max_uV = 1400000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE, + .always_on = 1, + .boot_on = 1, + }, + .num_consumer_supplies = 1, + .consumer_supplies = &max8952_consumer, +}; + static struct max8952_platform_data universal_max8952_pdata __initdata = { .gpio_vid0 = EXYNOS4_GPX0(3), .gpio_vid1 = EXYNOS4_GPX0(4), @@ -105,19 +118,7 @@ static struct max8952_platform_data universal_max8952_pdata __initdata = { .dvs_mode = { 48, 32, 28, 18 }, /* 1.25, 1.20, 1.05, 0.95V */ .sync_freq = 0, /* default: fastest */ .ramp_speed = 0, /* default: fastest */ - - .reg_data = { - .constraints = { - .name = "VARM_1.2V", - .min_uV = 770000, - .max_uV = 1400000, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE, - .always_on = 1, - .boot_on = 1, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &max8952_consumer, - }, + .reg_data = &universal_max8952_reg_data, }; static struct regulator_consumer_supply lp3974_buck1_consumer = diff --git a/arch/arm/mach-exynos/setup-usb-phy.c b/arch/arm/mach-exynos/setup-usb-phy.c index b81cc569a8dd..6af40662a449 100644 --- a/arch/arm/mach-exynos/setup-usb-phy.c +++ b/arch/arm/mach-exynos/setup-usb-phy.c @@ -204,9 +204,9 @@ static int exynos4210_usb_phy1_exit(struct platform_device *pdev) int s5p_usb_phy_init(struct platform_device *pdev, int type) { - if (type == S5P_USB_PHY_DEVICE) + if (type == USB_PHY_TYPE_DEVICE) return exynos4210_usb_phy0_init(pdev); - else if (type == S5P_USB_PHY_HOST) + else if (type == USB_PHY_TYPE_HOST) return exynos4210_usb_phy1_init(pdev); return -EINVAL; @@ -214,9 +214,9 @@ int s5p_usb_phy_init(struct platform_device *pdev, int type) int s5p_usb_phy_exit(struct platform_device *pdev, int type) { - if (type == S5P_USB_PHY_DEVICE) + if (type == USB_PHY_TYPE_DEVICE) return exynos4210_usb_phy0_exit(pdev); - else if (type == S5P_USB_PHY_HOST) + else if (type == USB_PHY_TYPE_HOST) return exynos4210_usb_phy1_exit(pdev); return -EINVAL; diff --git a/arch/arm/mach-gemini/idle.c b/arch/arm/mach-gemini/idle.c index 92bbd6bb600a..87dff4f5059e 100644 --- a/arch/arm/mach-gemini/idle.c +++ b/arch/arm/mach-gemini/idle.c @@ -13,9 +13,11 @@ static void gemini_idle(void) * will never wakeup... Acctualy it is not very good to enable * interrupts first since scheduler can miss a tick, but there is * no other way around this. Platforms that needs it for power saving - * should call enable_hlt() in init code, since by default it is + * should enable it in init code, since by default it is * disabled. */ + + /* FIXME: Enabling interrupts here is racy! */ local_irq_enable(); cpu_do_idle(); } diff --git a/arch/arm/mach-gemini/irq.c b/arch/arm/mach-gemini/irq.c index 020852d3bdd8..6d8f6d1669ff 100644 --- a/arch/arm/mach-gemini/irq.c +++ b/arch/arm/mach-gemini/irq.c @@ -15,6 +15,8 @@ #include <linux/stddef.h> #include <linux/list.h> #include <linux/sched.h> +#include <linux/cpu.h> + #include <asm/irq.h> #include <asm/mach/irq.h> #include <asm/system_misc.h> @@ -77,7 +79,7 @@ void __init gemini_init_irq(void) * Disable the idle handler by default since it is buggy * For more info see arch/arm/mach-gemini/idle.c */ - disable_hlt(); + cpu_idle_poll_ctrl(true); request_resource(&iomem_resource, &irq_resource); diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile index c4ce0906d76a..cb70961b6239 100644 --- a/arch/arm/mach-imx/Makefile +++ b/arch/arm/mach-imx/Makefile @@ -30,7 +30,7 @@ obj-$(CONFIG_MXC_DEBUG_BOARD) += 3ds_debugboard.o obj-$(CONFIG_CPU_FREQ_IMX) += cpufreq.o ifeq ($(CONFIG_CPU_IDLE),y) -obj-y += cpuidle.o +obj-$(CONFIG_SOC_IMX5) += cpuidle-imx5.o obj-$(CONFIG_SOC_IMX6Q) += cpuidle-imx6q.o endif diff --git a/arch/arm/mach-imx/clk-busy.c b/arch/arm/mach-imx/clk-busy.c index 1ab91b5209e6..85b728cc27ab 100644 --- a/arch/arm/mach-imx/clk-busy.c +++ b/arch/arm/mach-imx/clk-busy.c @@ -169,7 +169,7 @@ struct clk *imx_clk_busy_mux(const char *name, void __iomem *reg, u8 shift, busy->mux.reg = reg; busy->mux.shift = shift; - busy->mux.width = width; + busy->mux.mask = BIT(width) - 1; busy->mux.lock = &imx_ccm_lock; busy->mux_ops = &clk_mux_ops; diff --git a/arch/arm/mach-imx/cpufreq.c b/arch/arm/mach-imx/cpufreq.c index d8c75c3c925d..387dc4cceca2 100644 --- a/arch/arm/mach-imx/cpufreq.c +++ b/arch/arm/mach-imx/cpufreq.c @@ -87,13 +87,12 @@ static int mxc_set_target(struct cpufreq_policy *policy, freqs.old = clk_get_rate(cpu_clk) / 1000; freqs.new = freq_Hz / 1000; - freqs.cpu = 0; freqs.flags = 0; - cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); + cpufreq_notify_transition(policy, &freqs, CPUFREQ_PRECHANGE); ret = set_cpu_freq(freq_Hz); - cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); + cpufreq_notify_transition(policy, &freqs, CPUFREQ_POSTCHANGE); return ret; } @@ -145,14 +144,11 @@ static int mxc_cpufreq_init(struct cpufreq_policy *policy) imx_freq_table[i].frequency = CPUFREQ_TABLE_END; policy->cur = clk_get_rate(cpu_clk) / 1000; - policy->min = policy->cpuinfo.min_freq = cpu_freq_khz_min; - policy->max = policy->cpuinfo.max_freq = cpu_freq_khz_max; /* Manual states, that PLL stabilizes in two CLK32 periods */ policy->cpuinfo.transition_latency = 2 * NANOSECOND / CLK32_FREQ; ret = cpufreq_frequency_table_cpuinfo(policy, imx_freq_table); - if (ret < 0) { printk(KERN_ERR "%s: failed to register i.MXC CPUfreq with error code %d\n", __func__, ret); diff --git a/arch/arm/mach-imx/cpuidle-imx5.c b/arch/arm/mach-imx/cpuidle-imx5.c new file mode 100644 index 000000000000..5a47e3c6172f --- /dev/null +++ b/arch/arm/mach-imx/cpuidle-imx5.c @@ -0,0 +1,37 @@ +/* + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/cpuidle.h> +#include <linux/module.h> +#include <asm/system_misc.h> + +static int imx5_cpuidle_enter(struct cpuidle_device *dev, + struct cpuidle_driver *drv, int index) +{ + arm_pm_idle(); + return index; +} + +static struct cpuidle_driver imx5_cpuidle_driver = { + .name = "imx5_cpuidle", + .owner = THIS_MODULE, + .states[0] = { + .enter = imx5_cpuidle_enter, + .exit_latency = 2, + .target_residency = 1, + .flags = CPUIDLE_FLAG_TIME_VALID, + .name = "IMX5 SRPG", + .desc = "CPU state retained,powered off", + }, + .state_count = 1, +}; + +int __init imx5_cpuidle_init(void) +{ + return cpuidle_register(&imx5_cpuidle_driver, NULL); +} diff --git a/arch/arm/mach-imx/cpuidle-imx6q.c b/arch/arm/mach-imx/cpuidle-imx6q.c index d533e2695f0e..23ddfb693b2d 100644 --- a/arch/arm/mach-imx/cpuidle-imx6q.c +++ b/arch/arm/mach-imx/cpuidle-imx6q.c @@ -6,7 +6,6 @@ * published by the Free Software Foundation. */ -#include <linux/clockchips.h> #include <linux/cpuidle.h> #include <linux/module.h> #include <asm/cpuidle.h> @@ -21,10 +20,6 @@ static DEFINE_SPINLOCK(master_lock); static int imx6q_enter_wait(struct cpuidle_device *dev, struct cpuidle_driver *drv, int index) { - int cpu = dev->cpu; - - clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &cpu); - if (atomic_inc_return(&master) == num_online_cpus()) { /* * With this lock, we prevent other cpu to exit and enter @@ -43,26 +38,13 @@ idle: cpu_do_idle(); done: atomic_dec(&master); - clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT, &cpu); return index; } -/* - * For each cpu, setup the broadcast timer because local timer - * stops for the states other than WFI. - */ -static void imx6q_setup_broadcast_timer(void *arg) -{ - int cpu = smp_processor_id(); - - clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ON, &cpu); -} - static struct cpuidle_driver imx6q_cpuidle_driver = { .name = "imx6q_cpuidle", .owner = THIS_MODULE, - .en_core_tk_irqen = 1, .states = { /* WFI */ ARM_CPUIDLE_WFI_STATE, @@ -70,7 +52,8 @@ static struct cpuidle_driver imx6q_cpuidle_driver = { { .exit_latency = 50, .target_residency = 75, - .flags = CPUIDLE_FLAG_TIME_VALID, + .flags = CPUIDLE_FLAG_TIME_VALID | + CPUIDLE_FLAG_TIMER_STOP, .enter = imx6q_enter_wait, .name = "WAIT", .desc = "Clock off", @@ -88,8 +71,5 @@ int __init imx6q_cpuidle_init(void) /* Set chicken bit to get a reliable WAIT mode support */ imx6q_set_chicken_bit(); - /* Configure the broadcast timer on each cpu */ - on_each_cpu(imx6q_setup_broadcast_timer, NULL, 1); - - return imx_cpuidle_init(&imx6q_cpuidle_driver); + return cpuidle_register(&imx6q_cpuidle_driver, NULL); } diff --git a/arch/arm/mach-imx/cpuidle.c b/arch/arm/mach-imx/cpuidle.c deleted file mode 100644 index d4cb511a44a8..000000000000 --- a/arch/arm/mach-imx/cpuidle.c +++ /dev/null @@ -1,80 +0,0 @@ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - * Copyright 2012 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ - -#include <linux/cpuidle.h> -#include <linux/err.h> -#include <linux/hrtimer.h> -#include <linux/io.h> -#include <linux/kernel.h> -#include <linux/slab.h> - -static struct cpuidle_device __percpu * imx_cpuidle_devices; - -static void __init imx_cpuidle_devices_uninit(void) -{ - int cpu_id; - struct cpuidle_device *dev; - - for_each_possible_cpu(cpu_id) { - dev = per_cpu_ptr(imx_cpuidle_devices, cpu_id); - cpuidle_unregister_device(dev); - } - - free_percpu(imx_cpuidle_devices); -} - -int __init imx_cpuidle_init(struct cpuidle_driver *drv) -{ - struct cpuidle_device *dev; - int cpu_id, ret; - - if (drv->state_count > CPUIDLE_STATE_MAX) { - pr_err("%s: state_count exceeds maximum\n", __func__); - return -EINVAL; - } - - ret = cpuidle_register_driver(drv); - if (ret) { - pr_err("%s: Failed to register cpuidle driver with error: %d\n", - __func__, ret); - return ret; - } - - imx_cpuidle_devices = alloc_percpu(struct cpuidle_device); - if (imx_cpuidle_devices == NULL) { - ret = -ENOMEM; - goto unregister_drv; - } - - /* initialize state data for each cpuidle_device */ - for_each_possible_cpu(cpu_id) { - dev = per_cpu_ptr(imx_cpuidle_devices, cpu_id); - dev->cpu = cpu_id; - dev->state_count = drv->state_count; - - ret = cpuidle_register_device(dev); - if (ret) { - pr_err("%s: Failed to register cpu %u, error: %d\n", - __func__, cpu_id, ret); - goto uninit; - } - } - - return 0; - -uninit: - imx_cpuidle_devices_uninit(); - -unregister_drv: - cpuidle_unregister_driver(drv); - return ret; -} diff --git a/arch/arm/mach-imx/cpuidle.h b/arch/arm/mach-imx/cpuidle.h index e092d1359d94..786f98ecc145 100644 --- a/arch/arm/mach-imx/cpuidle.h +++ b/arch/arm/mach-imx/cpuidle.h @@ -10,18 +10,16 @@ * http://www.gnu.org/copyleft/gpl.html */ -#include <linux/cpuidle.h> - #ifdef CONFIG_CPU_IDLE -extern int imx_cpuidle_init(struct cpuidle_driver *drv); +extern int imx5_cpuidle_init(void); extern int imx6q_cpuidle_init(void); #else -static inline int imx_cpuidle_init(struct cpuidle_driver *drv) +static inline int imx5_cpuidle_init(void) { - return -ENODEV; + return 0; } static inline int imx6q_cpuidle_init(void) { - return -ENODEV; + return 0; } #endif diff --git a/arch/arm/mach-imx/pm-imx5.c b/arch/arm/mach-imx/pm-imx5.c index f67fd7ee8127..82e79c658eb2 100644 --- a/arch/arm/mach-imx/pm-imx5.c +++ b/arch/arm/mach-imx/pm-imx5.c @@ -149,33 +149,6 @@ static void imx5_pm_idle(void) imx5_cpu_do_idle(); } -static int imx5_cpuidle_enter(struct cpuidle_device *dev, - struct cpuidle_driver *drv, int idx) -{ - int ret; - - ret = imx5_cpu_do_idle(); - if (ret < 0) - return ret; - - return idx; -} - -static struct cpuidle_driver imx5_cpuidle_driver = { - .name = "imx5_cpuidle", - .owner = THIS_MODULE, - .en_core_tk_irqen = 1, - .states[0] = { - .enter = imx5_cpuidle_enter, - .exit_latency = 2, - .target_residency = 1, - .flags = CPUIDLE_FLAG_TIME_VALID, - .name = "IMX5 SRPG", - .desc = "CPU state retained,powered off", - }, - .state_count = 1, -}; - static int __init imx5_pm_common_init(void) { int ret; @@ -193,8 +166,7 @@ static int __init imx5_pm_common_init(void) /* Set the registers to the default cpu idle state. */ mx5_cpu_lp_set(IMX5_DEFAULT_CPU_IDLE_STATE); - imx_cpuidle_init(&imx5_cpuidle_driver); - return 0; + return imx5_cpuidle_init(); } void __init imx51_pm_init(void) diff --git a/arch/arm/mach-integrator/Makefile b/arch/arm/mach-integrator/Makefile index 5521d18bf19a..d14d6b76f4c2 100644 --- a/arch/arm/mach-integrator/Makefile +++ b/arch/arm/mach-integrator/Makefile @@ -9,5 +9,4 @@ obj-$(CONFIG_ARCH_INTEGRATOR_AP) += integrator_ap.o obj-$(CONFIG_ARCH_INTEGRATOR_CP) += integrator_cp.o obj-$(CONFIG_PCI) += pci_v3.o pci.o -obj-$(CONFIG_CPU_FREQ_INTEGRATOR) += cpu.o obj-$(CONFIG_INTEGRATOR_IMPD1) += impd1.o diff --git a/arch/arm/mach-integrator/cpu.c b/arch/arm/mach-integrator/cpu.c deleted file mode 100644 index 590c192cdf4d..000000000000 --- a/arch/arm/mach-integrator/cpu.c +++ /dev/null @@ -1,224 +0,0 @@ -/* - * linux/arch/arm/mach-integrator/cpu.c - * - * Copyright (C) 2001-2002 Deep Blue Solutions Ltd. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * CPU support functions - */ -#include <linux/module.h> -#include <linux/types.h> -#include <linux/kernel.h> -#include <linux/cpufreq.h> -#include <linux/sched.h> -#include <linux/smp.h> -#include <linux/init.h> -#include <linux/io.h> - -#include <mach/hardware.h> -#include <mach/platform.h> -#include <asm/mach-types.h> -#include <asm/hardware/icst.h> - -static struct cpufreq_driver integrator_driver; - -#define CM_ID __io_address(INTEGRATOR_HDR_ID) -#define CM_OSC __io_address(INTEGRATOR_HDR_OSC) -#define CM_STAT __io_address(INTEGRATOR_HDR_STAT) -#define CM_LOCK __io_address(INTEGRATOR_HDR_LOCK) - -static const struct icst_params lclk_params = { - .ref = 24000000, - .vco_max = ICST525_VCO_MAX_5V, - .vco_min = ICST525_VCO_MIN, - .vd_min = 8, - .vd_max = 132, - .rd_min = 24, - .rd_max = 24, - .s2div = icst525_s2div, - .idx2s = icst525_idx2s, -}; - -static const struct icst_params cclk_params = { - .ref = 24000000, - .vco_max = ICST525_VCO_MAX_5V, - .vco_min = ICST525_VCO_MIN, - .vd_min = 12, - .vd_max = 160, - .rd_min = 24, - .rd_max = 24, - .s2div = icst525_s2div, - .idx2s = icst525_idx2s, -}; - -/* - * Validate the speed policy. - */ -static int integrator_verify_policy(struct cpufreq_policy *policy) -{ - struct icst_vco vco; - - cpufreq_verify_within_limits(policy, - policy->cpuinfo.min_freq, - policy->cpuinfo.max_freq); - - vco = icst_hz_to_vco(&cclk_params, policy->max * 1000); - policy->max = icst_hz(&cclk_params, vco) / 1000; - - vco = icst_hz_to_vco(&cclk_params, policy->min * 1000); - policy->min = icst_hz(&cclk_params, vco) / 1000; - - cpufreq_verify_within_limits(policy, - policy->cpuinfo.min_freq, - policy->cpuinfo.max_freq); - - return 0; -} - - -static int integrator_set_target(struct cpufreq_policy *policy, - unsigned int target_freq, - unsigned int relation) -{ - cpumask_t cpus_allowed; - int cpu = policy->cpu; - struct icst_vco vco; - struct cpufreq_freqs freqs; - u_int cm_osc; - - /* - * Save this threads cpus_allowed mask. - */ - cpus_allowed = current->cpus_allowed; - - /* - * Bind to the specified CPU. When this call returns, - * we should be running on the right CPU. - */ - set_cpus_allowed(current, cpumask_of_cpu(cpu)); - BUG_ON(cpu != smp_processor_id()); - - /* get current setting */ - cm_osc = __raw_readl(CM_OSC); - - if (machine_is_integrator()) { - vco.s = (cm_osc >> 8) & 7; - } else if (machine_is_cintegrator()) { - vco.s = 1; - } - vco.v = cm_osc & 255; - vco.r = 22; - freqs.old = icst_hz(&cclk_params, vco) / 1000; - - /* icst_hz_to_vco rounds down -- so we need the next - * larger freq in case of CPUFREQ_RELATION_L. - */ - if (relation == CPUFREQ_RELATION_L) - target_freq += 999; - if (target_freq > policy->max) - target_freq = policy->max; - vco = icst_hz_to_vco(&cclk_params, target_freq * 1000); - freqs.new = icst_hz(&cclk_params, vco) / 1000; - - freqs.cpu = policy->cpu; - - if (freqs.old == freqs.new) { - set_cpus_allowed(current, cpus_allowed); - return 0; - } - - cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); - - cm_osc = __raw_readl(CM_OSC); - - if (machine_is_integrator()) { - cm_osc &= 0xfffff800; - cm_osc |= vco.s << 8; - } else if (machine_is_cintegrator()) { - cm_osc &= 0xffffff00; - } - cm_osc |= vco.v; - - __raw_writel(0xa05f, CM_LOCK); - __raw_writel(cm_osc, CM_OSC); - __raw_writel(0, CM_LOCK); - - /* - * Restore the CPUs allowed mask. - */ - set_cpus_allowed(current, cpus_allowed); - - cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); - - return 0; -} - -static unsigned int integrator_get(unsigned int cpu) -{ - cpumask_t cpus_allowed; - unsigned int current_freq; - u_int cm_osc; - struct icst_vco vco; - - cpus_allowed = current->cpus_allowed; - - set_cpus_allowed(current, cpumask_of_cpu(cpu)); - BUG_ON(cpu != smp_processor_id()); - - /* detect memory etc. */ - cm_osc = __raw_readl(CM_OSC); - - if (machine_is_integrator()) { - vco.s = (cm_osc >> 8) & 7; - } else { - vco.s = 1; - } - vco.v = cm_osc & 255; - vco.r = 22; - - current_freq = icst_hz(&cclk_params, vco) / 1000; /* current freq */ - - set_cpus_allowed(current, cpus_allowed); - - return current_freq; -} - -static int integrator_cpufreq_init(struct cpufreq_policy *policy) -{ - - /* set default policy and cpuinfo */ - policy->cpuinfo.max_freq = 160000; - policy->cpuinfo.min_freq = 12000; - policy->cpuinfo.transition_latency = 1000000; /* 1 ms, assumed */ - policy->cur = policy->min = policy->max = integrator_get(policy->cpu); - - return 0; -} - -static struct cpufreq_driver integrator_driver = { - .verify = integrator_verify_policy, - .target = integrator_set_target, - .get = integrator_get, - .init = integrator_cpufreq_init, - .name = "integrator", -}; - -static int __init integrator_cpu_init(void) -{ - return cpufreq_register_driver(&integrator_driver); -} - -static void __exit integrator_cpu_exit(void) -{ - cpufreq_unregister_driver(&integrator_driver); -} - -MODULE_AUTHOR ("Russell M. King"); -MODULE_DESCRIPTION ("cpufreq driver for ARM Integrator CPUs"); -MODULE_LICENSE ("GPL"); - -module_init(integrator_cpu_init); -module_exit(integrator_cpu_exit); diff --git a/arch/arm/mach-ixp4xx/common.c b/arch/arm/mach-ixp4xx/common.c index 1dbeb7c99d58..6600cff6bd92 100644 --- a/arch/arm/mach-ixp4xx/common.c +++ b/arch/arm/mach-ixp4xx/common.c @@ -29,6 +29,7 @@ #include <linux/io.h> #include <linux/export.h> #include <linux/gpio.h> +#include <linux/cpu.h> #include <mach/udc.h> #include <mach/hardware.h> @@ -239,7 +240,7 @@ void __init ixp4xx_init_irq(void) * ixp4xx does not implement the XScale PWRMODE register * so it must not call cpu_do_idle(). */ - disable_hlt(); + cpu_idle_poll_ctrl(true); /* Route all sources to IRQ instead of FIQ */ *IXP4XX_ICLR = 0x0; diff --git a/arch/arm/mach-mmp/aspenite.c b/arch/arm/mach-mmp/aspenite.c index 9f64d5632e07..76901f4ce611 100644 --- a/arch/arm/mach-mmp/aspenite.c +++ b/arch/arm/mach-mmp/aspenite.c @@ -223,13 +223,7 @@ static struct pxa27x_keypad_platform_data aspenite_keypad_info __initdata = { }; #if defined(CONFIG_USB_EHCI_MV) -static char *pxa168_sph_clock_name[] = { - [0] = "PXA168-USBCLK", -}; - static struct mv_usb_platform_data pxa168_sph_pdata = { - .clknum = 1, - .clkname = pxa168_sph_clock_name, .mode = MV_USB_MODE_HOST, .phy_init = pxa_usb_phy_init, .phy_deinit = pxa_usb_phy_deinit, diff --git a/arch/arm/mach-mmp/ttc_dkb.c b/arch/arm/mach-mmp/ttc_dkb.c index 22a9058f9f4d..6528a5fa6a26 100644 --- a/arch/arm/mach-mmp/ttc_dkb.c +++ b/arch/arm/mach-mmp/ttc_dkb.c @@ -162,13 +162,7 @@ static struct i2c_board_info ttc_dkb_i2c_info[] = { #ifdef CONFIG_USB_SUPPORT #if defined(CONFIG_USB_MV_UDC) || defined(CONFIG_USB_EHCI_MV_U2O) -static char *pxa910_usb_clock_name[] = { - [0] = "U2OCLK", -}; - static struct mv_usb_platform_data ttc_usb_pdata = { - .clknum = 1, - .clkname = pxa910_usb_clock_name, .vbus = NULL, .mode = MV_USB_MODE_OTG, .otg_force_a_bus_req = 1, diff --git a/arch/arm/mach-mvebu/irq-armada-370-xp.c b/arch/arm/mach-mvebu/irq-armada-370-xp.c index d5970f5a1e8d..830139a3e2ba 100644 --- a/arch/arm/mach-mvebu/irq-armada-370-xp.c +++ b/arch/arm/mach-mvebu/irq-armada-370-xp.c @@ -57,7 +57,7 @@ static struct irq_domain *armada_370_xp_mpic_domain; /* * In SMP mode: * For shared global interrupts, mask/unmask global enable bit - * For CPU interrtups, mask/unmask the calling CPU's bit + * For CPU interrupts, mask/unmask the calling CPU's bit */ static void armada_370_xp_irq_mask(struct irq_data *d) { diff --git a/arch/arm/mach-omap1/pm.c b/arch/arm/mach-omap1/pm.c index 7a7690ab6cb8..db37f49da5ac 100644 --- a/arch/arm/mach-omap1/pm.c +++ b/arch/arm/mach-omap1/pm.c @@ -43,6 +43,7 @@ #include <linux/module.h> #include <linux/io.h> #include <linux/atomic.h> +#include <linux/cpu.h> #include <asm/fncpy.h> #include <asm/system_misc.h> @@ -584,8 +585,7 @@ static void omap_pm_init_proc(void) static int omap_pm_prepare(void) { /* We cannot sleep in idle until we have resumed */ - disable_hlt(); - + cpu_idle_poll_ctrl(true); return 0; } @@ -621,7 +621,7 @@ static int omap_pm_enter(suspend_state_t state) static void omap_pm_finish(void) { - enable_hlt(); + cpu_idle_poll_ctrl(false); } diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h index d6ba13e1c540..14522d077c88 100644 --- a/arch/arm/mach-omap2/common.h +++ b/arch/arm/mach-omap2/common.h @@ -249,7 +249,6 @@ extern int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state); extern int omap4_finish_suspend(unsigned long cpu_state); extern void omap4_cpu_resume(void); extern int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state); -extern u32 omap4_mpuss_read_prev_context_state(void); #else static inline int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state) @@ -277,10 +276,6 @@ static inline int omap4_finish_suspend(unsigned long cpu_state) static inline void omap4_cpu_resume(void) {} -static inline u32 omap4_mpuss_read_prev_context_state(void) -{ - return 0; -} #endif struct omap_sdrc_params; diff --git a/arch/arm/mach-omap2/cpuidle34xx.c b/arch/arm/mach-omap2/cpuidle34xx.c index 80392fca86c6..cca045c95fbf 100644 --- a/arch/arm/mach-omap2/cpuidle34xx.c +++ b/arch/arm/mach-omap2/cpuidle34xx.c @@ -26,6 +26,7 @@ #include <linux/cpuidle.h> #include <linux/export.h> #include <linux/cpu_pm.h> +#include <asm/cpuidle.h> #include "powerdomain.h" #include "clockdomain.h" @@ -99,11 +100,15 @@ static struct omap3_idle_statedata omap3_idle_data[] = { }, }; -/* Private functions */ - -static int __omap3_enter_idle(struct cpuidle_device *dev, - struct cpuidle_driver *drv, - int index) +/** + * omap3_enter_idle - Programs OMAP3 to enter the specified state + * @dev: cpuidle device + * @drv: cpuidle driver + * @index: the index of state to be entered + */ +static int omap3_enter_idle(struct cpuidle_device *dev, + struct cpuidle_driver *drv, + int index) { struct omap3_idle_statedata *cx = &omap3_idle_data[index]; @@ -149,22 +154,6 @@ return_sleep_time: } /** - * omap3_enter_idle - Programs OMAP3 to enter the specified state - * @dev: cpuidle device - * @drv: cpuidle driver - * @index: the index of state to be entered - * - * Called from the CPUidle framework to program the device to the - * specified target state selected by the governor. - */ -static inline int omap3_enter_idle(struct cpuidle_device *dev, - struct cpuidle_driver *drv, - int index) -{ - return cpuidle_wrap_enter(dev, drv, index, __omap3_enter_idle); -} - -/** * next_valid_state - Find next valid C-state * @dev: cpuidle device * @drv: cpuidle driver @@ -271,11 +260,9 @@ static int omap3_enter_idle_bm(struct cpuidle_device *dev, return ret; } -static DEFINE_PER_CPU(struct cpuidle_device, omap3_idle_dev); - static struct cpuidle_driver omap3_idle_driver = { - .name = "omap3_idle", - .owner = THIS_MODULE, + .name = "omap3_idle", + .owner = THIS_MODULE, .states = { { .enter = omap3_enter_idle_bm, @@ -348,8 +335,6 @@ static struct cpuidle_driver omap3_idle_driver = { */ int __init omap3_idle_init(void) { - struct cpuidle_device *dev; - mpu_pd = pwrdm_lookup("mpu_pwrdm"); core_pd = pwrdm_lookup("core_pwrdm"); per_pd = pwrdm_lookup("per_pwrdm"); @@ -358,16 +343,5 @@ int __init omap3_idle_init(void) if (!mpu_pd || !core_pd || !per_pd || !cam_pd) return -ENODEV; - cpuidle_register_driver(&omap3_idle_driver); - - dev = &per_cpu(omap3_idle_dev, smp_processor_id()); - dev->cpu = 0; - - if (cpuidle_register_device(dev)) { - printk(KERN_ERR "%s: CPUidle register device failed\n", - __func__); - return -EIO; - } - - return 0; + return cpuidle_register(&omap3_idle_driver, NULL); } diff --git a/arch/arm/mach-omap2/cpuidle44xx.c b/arch/arm/mach-omap2/cpuidle44xx.c index d639aef0deda..5a286b56205e 100644 --- a/arch/arm/mach-omap2/cpuidle44xx.c +++ b/arch/arm/mach-omap2/cpuidle44xx.c @@ -1,7 +1,7 @@ /* - * OMAP4 CPU idle Routines + * OMAP4+ CPU idle Routines * - * Copyright (C) 2011 Texas Instruments, Inc. + * Copyright (C) 2011-2013 Texas Instruments, Inc. * Santosh Shilimkar <santosh.shilimkar@ti.com> * Rajendra Nayak <rnayak@ti.com> * @@ -14,8 +14,8 @@ #include <linux/cpuidle.h> #include <linux/cpu_pm.h> #include <linux/export.h> -#include <linux/clockchips.h> +#include <asm/cpuidle.h> #include <asm/proc-fns.h> #include "common.h" @@ -24,13 +24,13 @@ #include "clockdomain.h" /* Machine specific information */ -struct omap4_idle_statedata { +struct idle_statedata { u32 cpu_state; u32 mpu_logic_state; u32 mpu_state; }; -static struct omap4_idle_statedata omap4_idle_data[] = { +static struct idle_statedata omap4_idle_data[] = { { .cpu_state = PWRDM_POWER_ON, .mpu_state = PWRDM_POWER_ON, @@ -53,11 +53,12 @@ static struct clockdomain *cpu_clkdm[NR_CPUS]; static atomic_t abort_barrier; static bool cpu_done[NR_CPUS]; +static struct idle_statedata *state_ptr = &omap4_idle_data[0]; /* Private functions */ /** - * omap4_enter_idle_coupled_[simple/coupled] - OMAP4 cpuidle entry functions + * omap_enter_idle_[simple/coupled] - OMAP4PLUS cpuidle entry functions * @dev: cpuidle device * @drv: cpuidle driver * @index: the index of state to be entered @@ -66,7 +67,7 @@ static bool cpu_done[NR_CPUS]; * specified low power state selected by the governor. * Returns the amount of time spent in the low power state. */ -static int omap4_enter_idle_simple(struct cpuidle_device *dev, +static int omap_enter_idle_simple(struct cpuidle_device *dev, struct cpuidle_driver *drv, int index) { @@ -77,12 +78,11 @@ static int omap4_enter_idle_simple(struct cpuidle_device *dev, return index; } -static int omap4_enter_idle_coupled(struct cpuidle_device *dev, +static int omap_enter_idle_coupled(struct cpuidle_device *dev, struct cpuidle_driver *drv, int index) { - struct omap4_idle_statedata *cx = &omap4_idle_data[index]; - int cpu_id = smp_processor_id(); + struct idle_statedata *cx = state_ptr + index; local_fiq_disable(); @@ -109,8 +109,6 @@ static int omap4_enter_idle_coupled(struct cpuidle_device *dev, } } - clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &cpu_id); - /* * Call idle CPU PM enter notifier chain so that * VFP and per CPU interrupt context is saved. @@ -149,11 +147,10 @@ static int omap4_enter_idle_coupled(struct cpuidle_device *dev, * Call idle CPU cluster PM exit notifier chain * to restore GIC and wakeupgen context. */ - if (omap4_mpuss_read_prev_context_state()) + if ((cx->mpu_state == PWRDM_POWER_RET) && + (cx->mpu_logic_state == PWRDM_POWER_OFF)) cpu_cluster_pm_exit(); - clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT, &cpu_id); - fail: cpuidle_coupled_parallel_barrier(dev, &abort_barrier); cpu_done[dev->cpu] = false; @@ -163,49 +160,38 @@ fail: return index; } -/* - * For each cpu, setup the broadcast timer because local timers - * stops for the states above C1. - */ -static void omap_setup_broadcast_timer(void *arg) -{ - int cpu = smp_processor_id(); - clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ON, &cpu); -} - -static DEFINE_PER_CPU(struct cpuidle_device, omap4_idle_dev); - static struct cpuidle_driver omap4_idle_driver = { .name = "omap4_idle", .owner = THIS_MODULE, - .en_core_tk_irqen = 1, .states = { { /* C1 - CPU0 ON + CPU1 ON + MPU ON */ .exit_latency = 2 + 2, .target_residency = 5, .flags = CPUIDLE_FLAG_TIME_VALID, - .enter = omap4_enter_idle_simple, + .enter = omap_enter_idle_simple, .name = "C1", - .desc = "MPUSS ON" + .desc = "CPUx ON, MPUSS ON" }, { /* C2 - CPU0 OFF + CPU1 OFF + MPU CSWR */ .exit_latency = 328 + 440, .target_residency = 960, - .flags = CPUIDLE_FLAG_TIME_VALID | CPUIDLE_FLAG_COUPLED, - .enter = omap4_enter_idle_coupled, + .flags = CPUIDLE_FLAG_TIME_VALID | CPUIDLE_FLAG_COUPLED | + CPUIDLE_FLAG_TIMER_STOP, + .enter = omap_enter_idle_coupled, .name = "C2", - .desc = "MPUSS CSWR", + .desc = "CPUx OFF, MPUSS CSWR", }, { /* C3 - CPU0 OFF + CPU1 OFF + MPU OSWR */ .exit_latency = 460 + 518, .target_residency = 1100, - .flags = CPUIDLE_FLAG_TIME_VALID | CPUIDLE_FLAG_COUPLED, - .enter = omap4_enter_idle_coupled, + .flags = CPUIDLE_FLAG_TIME_VALID | CPUIDLE_FLAG_COUPLED | + CPUIDLE_FLAG_TIMER_STOP, + .enter = omap_enter_idle_coupled, .name = "C3", - .desc = "MPUSS OSWR", + .desc = "CPUx OFF, MPUSS OSWR", }, }, .state_count = ARRAY_SIZE(omap4_idle_data), @@ -215,16 +201,13 @@ static struct cpuidle_driver omap4_idle_driver = { /* Public functions */ /** - * omap4_idle_init - Init routine for OMAP4 idle + * omap4_idle_init - Init routine for OMAP4+ idle * - * Registers the OMAP4 specific cpuidle driver to the cpuidle + * Registers the OMAP4+ specific cpuidle driver to the cpuidle * framework with the valid set of states. */ int __init omap4_idle_init(void) { - struct cpuidle_device *dev; - unsigned int cpu_id = 0; - mpu_pd = pwrdm_lookup("mpu_pwrdm"); cpu_pd[0] = pwrdm_lookup("cpu0_pwrdm"); cpu_pd[1] = pwrdm_lookup("cpu1_pwrdm"); @@ -236,22 +219,5 @@ int __init omap4_idle_init(void) if (!cpu_clkdm[0] || !cpu_clkdm[1]) return -ENODEV; - /* Configure the broadcast timer on each cpu */ - on_each_cpu(omap_setup_broadcast_timer, NULL, 1); - - for_each_cpu(cpu_id, cpu_online_mask) { - dev = &per_cpu(omap4_idle_dev, cpu_id); - dev->cpu = cpu_id; -#ifdef CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED - dev->coupled_cpus = *cpu_online_mask; -#endif - cpuidle_register_driver(&omap4_idle_driver); - - if (cpuidle_register_device(dev)) { - pr_err("%s: CPUidle register failed\n", __func__); - return -EIO; - } - } - - return 0; + return cpuidle_register(&omap4_idle_driver, cpu_online_mask); } diff --git a/arch/arm/mach-omap2/omap-mpuss-lowpower.c b/arch/arm/mach-omap2/omap-mpuss-lowpower.c index 8bcb64bcdcdb..e80327b6c81f 100644 --- a/arch/arm/mach-omap2/omap-mpuss-lowpower.c +++ b/arch/arm/mach-omap2/omap-mpuss-lowpower.c @@ -139,20 +139,6 @@ static inline void cpu_clear_prev_logic_pwrst(unsigned int cpu_id) } } -/** - * omap4_mpuss_read_prev_context_state: - * Function returns the MPUSS previous context state - */ -u32 omap4_mpuss_read_prev_context_state(void) -{ - u32 reg; - - reg = omap4_prminst_read_inst_reg(OMAP4430_PRM_PARTITION, - OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET); - reg &= OMAP4430_LOSTCONTEXT_DFF_MASK; - return reg; -} - /* * Store the CPU cluster state for L2X0 low power operations. */ diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c index a202a4785104..e512253601c8 100644 --- a/arch/arm/mach-omap2/omap_hwmod.c +++ b/arch/arm/mach-omap2/omap_hwmod.c @@ -138,6 +138,7 @@ #include <linux/spinlock.h> #include <linux/slab.h> #include <linux/bootmem.h> +#include <linux/cpu.h> #include <asm/system_misc.h> @@ -2157,7 +2158,7 @@ static int _enable(struct omap_hwmod *oh) if (soc_ops.enable_module) soc_ops.enable_module(oh); if (oh->flags & HWMOD_BLOCK_WFI) - disable_hlt(); + cpu_idle_poll_ctrl(true); if (soc_ops.update_context_lost) soc_ops.update_context_lost(oh); @@ -2221,7 +2222,7 @@ static int _idle(struct omap_hwmod *oh) _del_initiator_dep(oh, mpu_oh); if (oh->flags & HWMOD_BLOCK_WFI) - enable_hlt(); + cpu_idle_poll_ctrl(false); if (soc_ops.disable_module) soc_ops.disable_module(oh); @@ -2331,7 +2332,7 @@ static int _shutdown(struct omap_hwmod *oh) _del_initiator_dep(oh, mpu_oh); /* XXX what about the other system initiators here? dma, dsp */ if (oh->flags & HWMOD_BLOCK_WFI) - enable_hlt(); + cpu_idle_poll_ctrl(false); if (soc_ops.disable_module) soc_ops.disable_module(oh); _disable_clocks(oh); diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index 9e0576569e07..eaba9dc91a0d 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -2714,16 +2714,22 @@ static struct omap_ocp2scp_dev ocp2scp_dev_attr[] = { { } }; -static struct omap_hwmod_opt_clk ocp2scp_usb_phy_opt_clks[] = { - { .role = "48mhz", .clk = "ocp2scp_usb_phy_phy_48m" }, -}; - /* ocp2scp_usb_phy */ static struct omap_hwmod omap44xx_ocp2scp_usb_phy_hwmod = { .name = "ocp2scp_usb_phy", .class = &omap44xx_ocp2scp_hwmod_class, .clkdm_name = "l3_init_clkdm", - .main_clk = "func_48m_fclk", + /* + * ocp2scp_usb_phy_phy_48m is provided by the OMAP4 PRCM IP + * block as an "optional clock," and normally should never be + * specified as the main_clk for an OMAP IP block. However it + * turns out that this clock is actually the main clock for + * the ocp2scp_usb_phy IP block: + * http://lists.infradead.org/pipermail/linux-arm-kernel/2012-September/119943.html + * So listing ocp2scp_usb_phy_phy_48m as a main_clk here seems + * to be the best workaround. + */ + .main_clk = "ocp2scp_usb_phy_phy_48m", .prcm = { .omap4 = { .clkctrl_offs = OMAP4_CM_L3INIT_USBPHYOCP2SCP_CLKCTRL_OFFSET, @@ -2732,8 +2738,6 @@ static struct omap_hwmod omap44xx_ocp2scp_usb_phy_hwmod = { }, }, .dev_attr = ocp2scp_dev_attr, - .opt_clks = ocp2scp_usb_phy_opt_clks, - .opt_clks_cnt = ARRAY_SIZE(ocp2scp_usb_phy_opt_clks), }; /* diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c index 673a4c1d1d76..e742118fcfd2 100644 --- a/arch/arm/mach-omap2/pm.c +++ b/arch/arm/mach-omap2/pm.c @@ -218,7 +218,7 @@ static int omap_pm_enter(suspend_state_t suspend_state) static int omap_pm_begin(suspend_state_t state) { - disable_hlt(); + cpu_idle_poll_ctrl(true); if (cpu_is_omap34xx()) omap_prcm_irq_prepare(); return 0; @@ -226,8 +226,7 @@ static int omap_pm_begin(suspend_state_t state) static void omap_pm_end(void) { - enable_hlt(); - return; + cpu_idle_poll_ctrl(false); } static void omap_pm_finish(void) @@ -265,6 +264,12 @@ static void __init omap4_init_voltages(void) omap2_set_init_voltage("iva", "dpll_iva_m5x2_ck", "iva"); } +static inline void omap_init_cpufreq(void) +{ + struct platform_device_info devinfo = { .name = "omap-cpufreq", }; + platform_device_register_full(&devinfo); +} + static int __init omap2_common_pm_init(void) { if (!of_have_populated_dt()) @@ -294,6 +299,9 @@ int __init omap2_common_pm_late_init(void) /* Smartreflex device init */ omap_devinit_smartreflex(); + + /* cpufreq dummy device instantiation */ + omap_init_cpufreq(); } #ifdef CONFIG_SUSPEND diff --git a/arch/arm/mach-omap2/pm44xx.c b/arch/arm/mach-omap2/pm44xx.c index ea62e75ef21d..152a10cf4f1d 100644 --- a/arch/arm/mach-omap2/pm44xx.c +++ b/arch/arm/mach-omap2/pm44xx.c @@ -126,8 +126,8 @@ static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused) * omap_default_idle - OMAP4 default ilde routine.' * * Implements OMAP4 memory, IO ordering requirements which can't be addressed - * with default cpu_do_idle() hook. Used by all CPUs with !CONFIG_CPUIDLE and - * by secondary CPU with CONFIG_CPUIDLE. + * with default cpu_do_idle() hook. Used by all CPUs with !CONFIG_CPU_IDLE and + * by secondary CPU with CONFIG_CPU_IDLE. */ static void omap_default_idle(void) { diff --git a/arch/arm/mach-orion5x/board-dt.c b/arch/arm/mach-orion5x/board-dt.c index 35a8014529ca..94fbb815680c 100644 --- a/arch/arm/mach-orion5x/board-dt.c +++ b/arch/arm/mach-orion5x/board-dt.c @@ -14,6 +14,7 @@ #include <linux/init.h> #include <linux/of.h> #include <linux/of_platform.h> +#include <linux/cpu.h> #include <asm/system_misc.h> #include <asm/mach/arch.h> #include <mach/orion5x.h> @@ -52,7 +53,7 @@ static void __init orion5x_dt_init(void) */ if (dev == MV88F5281_DEV_ID && rev == MV88F5281_REV_D0) { printk(KERN_INFO "Orion: Applying 5281 D0 WFI workaround.\n"); - disable_hlt(); + cpu_idle_poll_ctrl(true); } if (of_machine_is_compatible("lacie,ethernet-disk-mini-v2")) diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c index d068f1431c40..ad71c8a03ffd 100644 --- a/arch/arm/mach-orion5x/common.c +++ b/arch/arm/mach-orion5x/common.c @@ -293,7 +293,7 @@ void __init orion5x_init(void) */ if (dev == MV88F5281_DEV_ID && rev == MV88F5281_REV_D0) { printk(KERN_INFO "Orion: Applying 5281 D0 WFI workaround.\n"); - disable_hlt(); + cpu_idle_poll_ctrl(true); } /* diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile index 12c500558387..648867a8caa8 100644 --- a/arch/arm/mach-pxa/Makefile +++ b/arch/arm/mach-pxa/Makefile @@ -7,12 +7,6 @@ obj-y += clock.o devices.o generic.o irq.o \ time.o reset.o obj-$(CONFIG_PM) += pm.o sleep.o standby.o -ifeq ($(CONFIG_CPU_FREQ),y) -obj-$(CONFIG_PXA25x) += cpufreq-pxa2xx.o -obj-$(CONFIG_PXA27x) += cpufreq-pxa2xx.o -obj-$(CONFIG_PXA3xx) += cpufreq-pxa3xx.o -endif - # Generic drivers that other drivers may depend upon # SoC-specific code diff --git a/arch/arm/mach-pxa/cpufreq-pxa2xx.c b/arch/arm/mach-pxa/cpufreq-pxa2xx.c deleted file mode 100644 index 6a7aeab42f6c..000000000000 --- a/arch/arm/mach-pxa/cpufreq-pxa2xx.c +++ /dev/null @@ -1,494 +0,0 @@ -/* - * linux/arch/arm/mach-pxa/cpufreq-pxa2xx.c - * - * Copyright (C) 2002,2003 Intrinsyc Software - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - * History: - * 31-Jul-2002 : Initial version [FB] - * 29-Jan-2003 : added PXA255 support [FB] - * 20-Apr-2003 : ported to v2.5 (Dustin McIntire, Sensoria Corp.) - * - * Note: - * This driver may change the memory bus clock rate, but will not do any - * platform specific access timing changes... for example if you have flash - * memory connected to CS0, you will need to register a platform specific - * notifier which will adjust the memory access strobes to maintain a - * minimum strobe width. - * - */ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/sched.h> -#include <linux/init.h> -#include <linux/cpufreq.h> -#include <linux/err.h> -#include <linux/regulator/consumer.h> -#include <linux/io.h> - -#include <mach/pxa2xx-regs.h> -#include <mach/smemc.h> - -#ifdef DEBUG -static unsigned int freq_debug; -module_param(freq_debug, uint, 0); -MODULE_PARM_DESC(freq_debug, "Set the debug messages to on=1/off=0"); -#else -#define freq_debug 0 -#endif - -static struct regulator *vcc_core; - -static unsigned int pxa27x_maxfreq; -module_param(pxa27x_maxfreq, uint, 0); -MODULE_PARM_DESC(pxa27x_maxfreq, "Set the pxa27x maxfreq in MHz" - "(typically 624=>pxa270, 416=>pxa271, 520=>pxa272)"); - -typedef struct { - unsigned int khz; - unsigned int membus; - unsigned int cccr; - unsigned int div2; - unsigned int cclkcfg; - int vmin; - int vmax; -} pxa_freqs_t; - -/* Define the refresh period in mSec for the SDRAM and the number of rows */ -#define SDRAM_TREF 64 /* standard 64ms SDRAM */ -static unsigned int sdram_rows; - -#define CCLKCFG_TURBO 0x1 -#define CCLKCFG_FCS 0x2 -#define CCLKCFG_HALFTURBO 0x4 -#define CCLKCFG_FASTBUS 0x8 -#define MDREFR_DB2_MASK (MDREFR_K2DB2 | MDREFR_K1DB2) -#define MDREFR_DRI_MASK 0xFFF - -#define MDCNFG_DRAC2(mdcnfg) (((mdcnfg) >> 21) & 0x3) -#define MDCNFG_DRAC0(mdcnfg) (((mdcnfg) >> 5) & 0x3) - -/* - * PXA255 definitions - */ -/* Use the run mode frequencies for the CPUFREQ_POLICY_PERFORMANCE policy */ -#define CCLKCFG CCLKCFG_TURBO | CCLKCFG_FCS - -static pxa_freqs_t pxa255_run_freqs[] = -{ - /* CPU MEMBUS CCCR DIV2 CCLKCFG run turbo PXbus SDRAM */ - { 99500, 99500, 0x121, 1, CCLKCFG, -1, -1}, /* 99, 99, 50, 50 */ - {132700, 132700, 0x123, 1, CCLKCFG, -1, -1}, /* 133, 133, 66, 66 */ - {199100, 99500, 0x141, 0, CCLKCFG, -1, -1}, /* 199, 199, 99, 99 */ - {265400, 132700, 0x143, 1, CCLKCFG, -1, -1}, /* 265, 265, 133, 66 */ - {331800, 165900, 0x145, 1, CCLKCFG, -1, -1}, /* 331, 331, 166, 83 */ - {398100, 99500, 0x161, 0, CCLKCFG, -1, -1}, /* 398, 398, 196, 99 */ -}; - -/* Use the turbo mode frequencies for the CPUFREQ_POLICY_POWERSAVE policy */ -static pxa_freqs_t pxa255_turbo_freqs[] = -{ - /* CPU MEMBUS CCCR DIV2 CCLKCFG run turbo PXbus SDRAM */ - { 99500, 99500, 0x121, 1, CCLKCFG, -1, -1}, /* 99, 99, 50, 50 */ - {199100, 99500, 0x221, 0, CCLKCFG, -1, -1}, /* 99, 199, 50, 99 */ - {298500, 99500, 0x321, 0, CCLKCFG, -1, -1}, /* 99, 287, 50, 99 */ - {298600, 99500, 0x1c1, 0, CCLKCFG, -1, -1}, /* 199, 287, 99, 99 */ - {398100, 99500, 0x241, 0, CCLKCFG, -1, -1}, /* 199, 398, 99, 99 */ -}; - -#define NUM_PXA25x_RUN_FREQS ARRAY_SIZE(pxa255_run_freqs) -#define NUM_PXA25x_TURBO_FREQS ARRAY_SIZE(pxa255_turbo_freqs) - -static struct cpufreq_frequency_table - pxa255_run_freq_table[NUM_PXA25x_RUN_FREQS+1]; -static struct cpufreq_frequency_table - pxa255_turbo_freq_table[NUM_PXA25x_TURBO_FREQS+1]; - -static unsigned int pxa255_turbo_table; -module_param(pxa255_turbo_table, uint, 0); -MODULE_PARM_DESC(pxa255_turbo_table, "Selects the frequency table (0 = run table, !0 = turbo table)"); - -/* - * PXA270 definitions - * - * For the PXA27x: - * Control variables are A, L, 2N for CCCR; B, HT, T for CLKCFG. - * - * A = 0 => memory controller clock from table 3-7, - * A = 1 => memory controller clock = system bus clock - * Run mode frequency = 13 MHz * L - * Turbo mode frequency = 13 MHz * L * N - * System bus frequency = 13 MHz * L / (B + 1) - * - * In CCCR: - * A = 1 - * L = 16 oscillator to run mode ratio - * 2N = 6 2 * (turbo mode to run mode ratio) - * - * In CCLKCFG: - * B = 1 Fast bus mode - * HT = 0 Half-Turbo mode - * T = 1 Turbo mode - * - * For now, just support some of the combinations in table 3-7 of - * PXA27x Processor Family Developer's Manual to simplify frequency - * change sequences. - */ -#define PXA27x_CCCR(A, L, N2) (A << 25 | N2 << 7 | L) -#define CCLKCFG2(B, HT, T) \ - (CCLKCFG_FCS | \ - ((B) ? CCLKCFG_FASTBUS : 0) | \ - ((HT) ? CCLKCFG_HALFTURBO : 0) | \ - ((T) ? CCLKCFG_TURBO : 0)) - -static pxa_freqs_t pxa27x_freqs[] = { - {104000, 104000, PXA27x_CCCR(1, 8, 2), 0, CCLKCFG2(1, 0, 1), 900000, 1705000 }, - {156000, 104000, PXA27x_CCCR(1, 8, 3), 0, CCLKCFG2(1, 0, 1), 1000000, 1705000 }, - {208000, 208000, PXA27x_CCCR(0, 16, 2), 1, CCLKCFG2(0, 0, 1), 1180000, 1705000 }, - {312000, 208000, PXA27x_CCCR(1, 16, 3), 1, CCLKCFG2(1, 0, 1), 1250000, 1705000 }, - {416000, 208000, PXA27x_CCCR(1, 16, 4), 1, CCLKCFG2(1, 0, 1), 1350000, 1705000 }, - {520000, 208000, PXA27x_CCCR(1, 16, 5), 1, CCLKCFG2(1, 0, 1), 1450000, 1705000 }, - {624000, 208000, PXA27x_CCCR(1, 16, 6), 1, CCLKCFG2(1, 0, 1), 1550000, 1705000 } -}; - -#define NUM_PXA27x_FREQS ARRAY_SIZE(pxa27x_freqs) -static struct cpufreq_frequency_table - pxa27x_freq_table[NUM_PXA27x_FREQS+1]; - -extern unsigned get_clk_frequency_khz(int info); - -#ifdef CONFIG_REGULATOR - -static int pxa_cpufreq_change_voltage(pxa_freqs_t *pxa_freq) -{ - int ret = 0; - int vmin, vmax; - - if (!cpu_is_pxa27x()) - return 0; - - vmin = pxa_freq->vmin; - vmax = pxa_freq->vmax; - if ((vmin == -1) || (vmax == -1)) - return 0; - - ret = regulator_set_voltage(vcc_core, vmin, vmax); - if (ret) - pr_err("cpufreq: Failed to set vcc_core in [%dmV..%dmV]\n", - vmin, vmax); - return ret; -} - -static __init void pxa_cpufreq_init_voltages(void) -{ - vcc_core = regulator_get(NULL, "vcc_core"); - if (IS_ERR(vcc_core)) { - pr_info("cpufreq: Didn't find vcc_core regulator\n"); - vcc_core = NULL; - } else { - pr_info("cpufreq: Found vcc_core regulator\n"); - } -} -#else -static int pxa_cpufreq_change_voltage(pxa_freqs_t *pxa_freq) -{ - return 0; -} - -static __init void pxa_cpufreq_init_voltages(void) { } -#endif - -static void find_freq_tables(struct cpufreq_frequency_table **freq_table, - pxa_freqs_t **pxa_freqs) -{ - if (cpu_is_pxa25x()) { - if (!pxa255_turbo_table) { - *pxa_freqs = pxa255_run_freqs; - *freq_table = pxa255_run_freq_table; - } else { - *pxa_freqs = pxa255_turbo_freqs; - *freq_table = pxa255_turbo_freq_table; - } - } - if (cpu_is_pxa27x()) { - *pxa_freqs = pxa27x_freqs; - *freq_table = pxa27x_freq_table; - } -} - -static void pxa27x_guess_max_freq(void) -{ - if (!pxa27x_maxfreq) { - pxa27x_maxfreq = 416000; - printk(KERN_INFO "PXA CPU 27x max frequency not defined " - "(pxa27x_maxfreq), assuming pxa271 with %dkHz maxfreq\n", - pxa27x_maxfreq); - } else { - pxa27x_maxfreq *= 1000; - } -} - -static void init_sdram_rows(void) -{ - uint32_t mdcnfg = __raw_readl(MDCNFG); - unsigned int drac2 = 0, drac0 = 0; - - if (mdcnfg & (MDCNFG_DE2 | MDCNFG_DE3)) - drac2 = MDCNFG_DRAC2(mdcnfg); - - if (mdcnfg & (MDCNFG_DE0 | MDCNFG_DE1)) - drac0 = MDCNFG_DRAC0(mdcnfg); - - sdram_rows = 1 << (11 + max(drac0, drac2)); -} - -static u32 mdrefr_dri(unsigned int freq) -{ - u32 interval = freq * SDRAM_TREF / sdram_rows; - - return (interval - (cpu_is_pxa27x() ? 31 : 0)) / 32; -} - -/* find a valid frequency point */ -static int pxa_verify_policy(struct cpufreq_policy *policy) -{ - struct cpufreq_frequency_table *pxa_freqs_table; - pxa_freqs_t *pxa_freqs; - int ret; - - find_freq_tables(&pxa_freqs_table, &pxa_freqs); - ret = cpufreq_frequency_table_verify(policy, pxa_freqs_table); - - if (freq_debug) - pr_debug("Verified CPU policy: %dKhz min to %dKhz max\n", - policy->min, policy->max); - - return ret; -} - -static unsigned int pxa_cpufreq_get(unsigned int cpu) -{ - return get_clk_frequency_khz(0); -} - -static int pxa_set_target(struct cpufreq_policy *policy, - unsigned int target_freq, - unsigned int relation) -{ - struct cpufreq_frequency_table *pxa_freqs_table; - pxa_freqs_t *pxa_freq_settings; - struct cpufreq_freqs freqs; - unsigned int idx; - unsigned long flags; - unsigned int new_freq_cpu, new_freq_mem; - unsigned int unused, preset_mdrefr, postset_mdrefr, cclkcfg; - int ret = 0; - - /* Get the current policy */ - find_freq_tables(&pxa_freqs_table, &pxa_freq_settings); - - /* Lookup the next frequency */ - if (cpufreq_frequency_table_target(policy, pxa_freqs_table, - target_freq, relation, &idx)) { - return -EINVAL; - } - - new_freq_cpu = pxa_freq_settings[idx].khz; - new_freq_mem = pxa_freq_settings[idx].membus; - freqs.old = policy->cur; - freqs.new = new_freq_cpu; - freqs.cpu = policy->cpu; - - if (freq_debug) - pr_debug("Changing CPU frequency to %d Mhz, (SDRAM %d Mhz)\n", - freqs.new / 1000, (pxa_freq_settings[idx].div2) ? - (new_freq_mem / 2000) : (new_freq_mem / 1000)); - - if (vcc_core && freqs.new > freqs.old) - ret = pxa_cpufreq_change_voltage(&pxa_freq_settings[idx]); - if (ret) - return ret; - /* - * Tell everyone what we're about to do... - * you should add a notify client with any platform specific - * Vcc changing capability - */ - cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); - - /* Calculate the next MDREFR. If we're slowing down the SDRAM clock - * we need to preset the smaller DRI before the change. If we're - * speeding up we need to set the larger DRI value after the change. - */ - preset_mdrefr = postset_mdrefr = __raw_readl(MDREFR); - if ((preset_mdrefr & MDREFR_DRI_MASK) > mdrefr_dri(new_freq_mem)) { - preset_mdrefr = (preset_mdrefr & ~MDREFR_DRI_MASK); - preset_mdrefr |= mdrefr_dri(new_freq_mem); - } - postset_mdrefr = - (postset_mdrefr & ~MDREFR_DRI_MASK) | mdrefr_dri(new_freq_mem); - - /* If we're dividing the memory clock by two for the SDRAM clock, this - * must be set prior to the change. Clearing the divide must be done - * after the change. - */ - if (pxa_freq_settings[idx].div2) { - preset_mdrefr |= MDREFR_DB2_MASK; - postset_mdrefr |= MDREFR_DB2_MASK; - } else { - postset_mdrefr &= ~MDREFR_DB2_MASK; - } - - local_irq_save(flags); - - /* Set new the CCCR and prepare CCLKCFG */ - CCCR = pxa_freq_settings[idx].cccr; - cclkcfg = pxa_freq_settings[idx].cclkcfg; - - asm volatile(" \n\ - ldr r4, [%1] /* load MDREFR */ \n\ - b 2f \n\ - .align 5 \n\ -1: \n\ - str %3, [%1] /* preset the MDREFR */ \n\ - mcr p14, 0, %2, c6, c0, 0 /* set CCLKCFG[FCS] */ \n\ - str %4, [%1] /* postset the MDREFR */ \n\ - \n\ - b 3f \n\ -2: b 1b \n\ -3: nop \n\ - " - : "=&r" (unused) - : "r" (MDREFR), "r" (cclkcfg), - "r" (preset_mdrefr), "r" (postset_mdrefr) - : "r4", "r5"); - local_irq_restore(flags); - - /* - * Tell everyone what we've just done... - * you should add a notify client with any platform specific - * SDRAM refresh timer adjustments - */ - cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); - - /* - * Even if voltage setting fails, we don't report it, as the frequency - * change succeeded. The voltage reduction is not a critical failure, - * only power savings will suffer from this. - * - * Note: if the voltage change fails, and a return value is returned, a - * bug is triggered (seems a deadlock). Should anybody find out where, - * the "return 0" should become a "return ret". - */ - if (vcc_core && freqs.new < freqs.old) - ret = pxa_cpufreq_change_voltage(&pxa_freq_settings[idx]); - - return 0; -} - -static int pxa_cpufreq_init(struct cpufreq_policy *policy) -{ - int i; - unsigned int freq; - struct cpufreq_frequency_table *pxa255_freq_table; - pxa_freqs_t *pxa255_freqs; - - /* try to guess pxa27x cpu */ - if (cpu_is_pxa27x()) - pxa27x_guess_max_freq(); - - pxa_cpufreq_init_voltages(); - - init_sdram_rows(); - - /* set default policy and cpuinfo */ - policy->cpuinfo.transition_latency = 1000; /* FIXME: 1 ms, assumed */ - policy->cur = get_clk_frequency_khz(0); /* current freq */ - policy->min = policy->max = policy->cur; - - /* Generate pxa25x the run cpufreq_frequency_table struct */ - for (i = 0; i < NUM_PXA25x_RUN_FREQS; i++) { - pxa255_run_freq_table[i].frequency = pxa255_run_freqs[i].khz; - pxa255_run_freq_table[i].index = i; - } - pxa255_run_freq_table[i].frequency = CPUFREQ_TABLE_END; - - /* Generate pxa25x the turbo cpufreq_frequency_table struct */ - for (i = 0; i < NUM_PXA25x_TURBO_FREQS; i++) { - pxa255_turbo_freq_table[i].frequency = - pxa255_turbo_freqs[i].khz; - pxa255_turbo_freq_table[i].index = i; - } - pxa255_turbo_freq_table[i].frequency = CPUFREQ_TABLE_END; - - pxa255_turbo_table = !!pxa255_turbo_table; - - /* Generate the pxa27x cpufreq_frequency_table struct */ - for (i = 0; i < NUM_PXA27x_FREQS; i++) { - freq = pxa27x_freqs[i].khz; - if (freq > pxa27x_maxfreq) - break; - pxa27x_freq_table[i].frequency = freq; - pxa27x_freq_table[i].index = i; - } - pxa27x_freq_table[i].index = i; - pxa27x_freq_table[i].frequency = CPUFREQ_TABLE_END; - - /* - * Set the policy's minimum and maximum frequencies from the tables - * just constructed. This sets cpuinfo.mxx_freq, min and max. - */ - if (cpu_is_pxa25x()) { - find_freq_tables(&pxa255_freq_table, &pxa255_freqs); - pr_info("PXA255 cpufreq using %s frequency table\n", - pxa255_turbo_table ? "turbo" : "run"); - cpufreq_frequency_table_cpuinfo(policy, pxa255_freq_table); - } - else if (cpu_is_pxa27x()) - cpufreq_frequency_table_cpuinfo(policy, pxa27x_freq_table); - - printk(KERN_INFO "PXA CPU frequency change support initialized\n"); - - return 0; -} - -static struct cpufreq_driver pxa_cpufreq_driver = { - .verify = pxa_verify_policy, - .target = pxa_set_target, - .init = pxa_cpufreq_init, - .get = pxa_cpufreq_get, - .name = "PXA2xx", -}; - -static int __init pxa_cpu_init(void) -{ - int ret = -ENODEV; - if (cpu_is_pxa25x() || cpu_is_pxa27x()) - ret = cpufreq_register_driver(&pxa_cpufreq_driver); - return ret; -} - -static void __exit pxa_cpu_exit(void) -{ - cpufreq_unregister_driver(&pxa_cpufreq_driver); -} - - -MODULE_AUTHOR("Intrinsyc Software Inc."); -MODULE_DESCRIPTION("CPU frequency changing driver for the PXA architecture"); -MODULE_LICENSE("GPL"); -module_init(pxa_cpu_init); -module_exit(pxa_cpu_exit); diff --git a/arch/arm/mach-pxa/cpufreq-pxa3xx.c b/arch/arm/mach-pxa/cpufreq-pxa3xx.c deleted file mode 100644 index b85b4ab7aac6..000000000000 --- a/arch/arm/mach-pxa/cpufreq-pxa3xx.c +++ /dev/null @@ -1,258 +0,0 @@ -/* - * linux/arch/arm/mach-pxa/cpufreq-pxa3xx.c - * - * Copyright (C) 2008 Marvell International Ltd. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/sched.h> -#include <linux/init.h> -#include <linux/cpufreq.h> -#include <linux/slab.h> -#include <linux/io.h> - -#include <mach/pxa3xx-regs.h> - -#include "generic.h" - -#define HSS_104M (0) -#define HSS_156M (1) -#define HSS_208M (2) -#define HSS_312M (3) - -#define SMCFS_78M (0) -#define SMCFS_104M (2) -#define SMCFS_208M (5) - -#define SFLFS_104M (0) -#define SFLFS_156M (1) -#define SFLFS_208M (2) -#define SFLFS_312M (3) - -#define XSPCLK_156M (0) -#define XSPCLK_NONE (3) - -#define DMCFS_26M (0) -#define DMCFS_260M (3) - -struct pxa3xx_freq_info { - unsigned int cpufreq_mhz; - unsigned int core_xl : 5; - unsigned int core_xn : 3; - unsigned int hss : 2; - unsigned int dmcfs : 2; - unsigned int smcfs : 3; - unsigned int sflfs : 2; - unsigned int df_clkdiv : 3; - - int vcc_core; /* in mV */ - int vcc_sram; /* in mV */ -}; - -#define OP(cpufreq, _xl, _xn, _hss, _dmc, _smc, _sfl, _dfi, vcore, vsram) \ -{ \ - .cpufreq_mhz = cpufreq, \ - .core_xl = _xl, \ - .core_xn = _xn, \ - .hss = HSS_##_hss##M, \ - .dmcfs = DMCFS_##_dmc##M, \ - .smcfs = SMCFS_##_smc##M, \ - .sflfs = SFLFS_##_sfl##M, \ - .df_clkdiv = _dfi, \ - .vcc_core = vcore, \ - .vcc_sram = vsram, \ -} - -static struct pxa3xx_freq_info pxa300_freqs[] = { - /* CPU XL XN HSS DMEM SMEM SRAM DFI VCC_CORE VCC_SRAM */ - OP(104, 8, 1, 104, 260, 78, 104, 3, 1000, 1100), /* 104MHz */ - OP(208, 16, 1, 104, 260, 104, 156, 2, 1000, 1100), /* 208MHz */ - OP(416, 16, 2, 156, 260, 104, 208, 2, 1100, 1200), /* 416MHz */ - OP(624, 24, 2, 208, 260, 208, 312, 3, 1375, 1400), /* 624MHz */ -}; - -static struct pxa3xx_freq_info pxa320_freqs[] = { - /* CPU XL XN HSS DMEM SMEM SRAM DFI VCC_CORE VCC_SRAM */ - OP(104, 8, 1, 104, 260, 78, 104, 3, 1000, 1100), /* 104MHz */ - OP(208, 16, 1, 104, 260, 104, 156, 2, 1000, 1100), /* 208MHz */ - OP(416, 16, 2, 156, 260, 104, 208, 2, 1100, 1200), /* 416MHz */ - OP(624, 24, 2, 208, 260, 208, 312, 3, 1375, 1400), /* 624MHz */ - OP(806, 31, 2, 208, 260, 208, 312, 3, 1400, 1400), /* 806MHz */ -}; - -static unsigned int pxa3xx_freqs_num; -static struct pxa3xx_freq_info *pxa3xx_freqs; -static struct cpufreq_frequency_table *pxa3xx_freqs_table; - -static int setup_freqs_table(struct cpufreq_policy *policy, - struct pxa3xx_freq_info *freqs, int num) -{ - struct cpufreq_frequency_table *table; - int i; - - table = kzalloc((num + 1) * sizeof(*table), GFP_KERNEL); - if (table == NULL) - return -ENOMEM; - - for (i = 0; i < num; i++) { - table[i].index = i; - table[i].frequency = freqs[i].cpufreq_mhz * 1000; - } - table[num].index = i; - table[num].frequency = CPUFREQ_TABLE_END; - - pxa3xx_freqs = freqs; - pxa3xx_freqs_num = num; - pxa3xx_freqs_table = table; - - return cpufreq_frequency_table_cpuinfo(policy, table); -} - -static void __update_core_freq(struct pxa3xx_freq_info *info) -{ - uint32_t mask = ACCR_XN_MASK | ACCR_XL_MASK; - uint32_t accr = ACCR; - uint32_t xclkcfg; - - accr &= ~(ACCR_XN_MASK | ACCR_XL_MASK | ACCR_XSPCLK_MASK); - accr |= ACCR_XN(info->core_xn) | ACCR_XL(info->core_xl); - - /* No clock until core PLL is re-locked */ - accr |= ACCR_XSPCLK(XSPCLK_NONE); - - xclkcfg = (info->core_xn == 2) ? 0x3 : 0x2; /* turbo bit */ - - ACCR = accr; - __asm__("mcr p14, 0, %0, c6, c0, 0\n" : : "r"(xclkcfg)); - - while ((ACSR & mask) != (accr & mask)) - cpu_relax(); -} - -static void __update_bus_freq(struct pxa3xx_freq_info *info) -{ - uint32_t mask; - uint32_t accr = ACCR; - - mask = ACCR_SMCFS_MASK | ACCR_SFLFS_MASK | ACCR_HSS_MASK | - ACCR_DMCFS_MASK; - - accr &= ~mask; - accr |= ACCR_SMCFS(info->smcfs) | ACCR_SFLFS(info->sflfs) | - ACCR_HSS(info->hss) | ACCR_DMCFS(info->dmcfs); - - ACCR = accr; - - while ((ACSR & mask) != (accr & mask)) - cpu_relax(); -} - -static int pxa3xx_cpufreq_verify(struct cpufreq_policy *policy) -{ - return cpufreq_frequency_table_verify(policy, pxa3xx_freqs_table); -} - -static unsigned int pxa3xx_cpufreq_get(unsigned int cpu) -{ - return pxa3xx_get_clk_frequency_khz(0); -} - -static int pxa3xx_cpufreq_set(struct cpufreq_policy *policy, - unsigned int target_freq, - unsigned int relation) -{ - struct pxa3xx_freq_info *next; - struct cpufreq_freqs freqs; - unsigned long flags; - int idx; - - if (policy->cpu != 0) - return -EINVAL; - - /* Lookup the next frequency */ - if (cpufreq_frequency_table_target(policy, pxa3xx_freqs_table, - target_freq, relation, &idx)) - return -EINVAL; - - next = &pxa3xx_freqs[idx]; - - freqs.old = policy->cur; - freqs.new = next->cpufreq_mhz * 1000; - freqs.cpu = policy->cpu; - - pr_debug("CPU frequency from %d MHz to %d MHz%s\n", - freqs.old / 1000, freqs.new / 1000, - (freqs.old == freqs.new) ? " (skipped)" : ""); - - if (freqs.old == target_freq) - return 0; - - cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); - - local_irq_save(flags); - __update_core_freq(next); - __update_bus_freq(next); - local_irq_restore(flags); - - cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); - - return 0; -} - -static int pxa3xx_cpufreq_init(struct cpufreq_policy *policy) -{ - int ret = -EINVAL; - - /* set default policy and cpuinfo */ - policy->cpuinfo.min_freq = 104000; - policy->cpuinfo.max_freq = (cpu_is_pxa320()) ? 806000 : 624000; - policy->cpuinfo.transition_latency = 1000; /* FIXME: 1 ms, assumed */ - policy->max = pxa3xx_get_clk_frequency_khz(0); - policy->cur = policy->min = policy->max; - - if (cpu_is_pxa300() || cpu_is_pxa310()) - ret = setup_freqs_table(policy, ARRAY_AND_SIZE(pxa300_freqs)); - - if (cpu_is_pxa320()) - ret = setup_freqs_table(policy, ARRAY_AND_SIZE(pxa320_freqs)); - - if (ret) { - pr_err("failed to setup frequency table\n"); - return ret; - } - - pr_info("CPUFREQ support for PXA3xx initialized\n"); - return 0; -} - -static struct cpufreq_driver pxa3xx_cpufreq_driver = { - .verify = pxa3xx_cpufreq_verify, - .target = pxa3xx_cpufreq_set, - .init = pxa3xx_cpufreq_init, - .get = pxa3xx_cpufreq_get, - .name = "pxa3xx-cpufreq", -}; - -static int __init cpufreq_init(void) -{ - if (cpu_is_pxa3xx()) - return cpufreq_register_driver(&pxa3xx_cpufreq_driver); - - return 0; -} -module_init(cpufreq_init); - -static void __exit cpufreq_exit(void) -{ - cpufreq_unregister_driver(&pxa3xx_cpufreq_driver); -} -module_exit(cpufreq_exit); - -MODULE_DESCRIPTION("CPU frequency scaling driver for PXA3xx"); -MODULE_LICENSE("GPL"); diff --git a/arch/arm/mach-pxa/include/mach/generic.h b/arch/arm/mach-pxa/include/mach/generic.h new file mode 100644 index 000000000000..665542e0c9e2 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/generic.h @@ -0,0 +1 @@ +#include "../../generic.h" diff --git a/arch/arm/mach-s3c24xx/clock-s3c2440.c b/arch/arm/mach-s3c24xx/clock-s3c2440.c index 04b87ec92537..1069b5680826 100644 --- a/arch/arm/mach-s3c24xx/clock-s3c2440.c +++ b/arch/arm/mach-s3c24xx/clock-s3c2440.c @@ -123,6 +123,11 @@ static struct clk s3c2440_clk_ac97 = { .ctrlbit = S3C2440_CLKCON_AC97, }; +#define S3C24XX_VA_UART0 (S3C_VA_UART) +#define S3C24XX_VA_UART1 (S3C_VA_UART + 0x4000 ) +#define S3C24XX_VA_UART2 (S3C_VA_UART + 0x8000 ) +#define S3C24XX_VA_UART3 (S3C_VA_UART + 0xC000 ) + static unsigned long s3c2440_fclk_n_getrate(struct clk *clk) { unsigned long ucon0, ucon1, ucon2, divisor; diff --git a/arch/arm/mach-s3c24xx/common.c b/arch/arm/mach-s3c24xx/common.c index 6bcf87f65f9e..92e609440c57 100644 --- a/arch/arm/mach-s3c24xx/common.c +++ b/arch/arm/mach-s3c24xx/common.c @@ -239,6 +239,11 @@ void __init s3c24xx_init_io(struct map_desc *mach_desc, int size) /* Serial port registrations */ +#define S3C2410_PA_UART0 (S3C24XX_PA_UART) +#define S3C2410_PA_UART1 (S3C24XX_PA_UART + 0x4000 ) +#define S3C2410_PA_UART2 (S3C24XX_PA_UART + 0x8000 ) +#define S3C2443_PA_UART3 (S3C24XX_PA_UART + 0xC000 ) + static struct resource s3c2410_uart0_resource[] = { [0] = DEFINE_RES_MEM(S3C2410_PA_UART0, SZ_16K), [1] = DEFINE_RES_NAMED(IRQ_S3CUART_RX0, \ diff --git a/arch/arm/mach-s3c24xx/cpufreq.c b/arch/arm/mach-s3c24xx/cpufreq.c index 5f181e733eee..3c0e78ede0da 100644 --- a/arch/arm/mach-s3c24xx/cpufreq.c +++ b/arch/arm/mach-s3c24xx/cpufreq.c @@ -204,7 +204,6 @@ static int s3c_cpufreq_settarget(struct cpufreq_policy *policy, freqs.old = cpu_cur.freq; freqs.new = cpu_new.freq; - freqs.freqs.cpu = 0; freqs.freqs.old = cpu_cur.freq.armclk / 1000; freqs.freqs.new = cpu_new.freq.armclk / 1000; @@ -218,9 +217,7 @@ static int s3c_cpufreq_settarget(struct cpufreq_policy *policy, s3c_cpufreq_updateclk(clk_pclk, cpu_new.freq.pclk); /* start the frequency change */ - - if (policy) - cpufreq_notify_transition(&freqs.freqs, CPUFREQ_PRECHANGE); + cpufreq_notify_transition(policy, &freqs.freqs, CPUFREQ_PRECHANGE); /* If hclk is staying the same, then we do not need to * re-write the IO or the refresh timings whilst we are changing @@ -264,8 +261,7 @@ static int s3c_cpufreq_settarget(struct cpufreq_policy *policy, local_irq_restore(flags); /* notify everyone we've done this */ - if (policy) - cpufreq_notify_transition(&freqs.freqs, CPUFREQ_POSTCHANGE); + cpufreq_notify_transition(policy, &freqs.freqs, CPUFREQ_POSTCHANGE); s3c_freq_dbg("%s: finished\n", __func__); return 0; diff --git a/arch/arm/mach-s3c64xx/cpuidle.c b/arch/arm/mach-s3c64xx/cpuidle.c index ead5fab0dbb5..3c8ab07c2012 100644 --- a/arch/arm/mach-s3c64xx/cpuidle.c +++ b/arch/arm/mach-s3c64xx/cpuidle.c @@ -40,12 +40,9 @@ static int s3c64xx_enter_idle(struct cpuidle_device *dev, return index; } -static DEFINE_PER_CPU(struct cpuidle_device, s3c64xx_cpuidle_device); - static struct cpuidle_driver s3c64xx_cpuidle_driver = { .name = "s3c64xx_cpuidle", .owner = THIS_MODULE, - .en_core_tk_irqen = 1, .states = { { .enter = s3c64xx_enter_idle, @@ -61,16 +58,6 @@ static struct cpuidle_driver s3c64xx_cpuidle_driver = { static int __init s3c64xx_init_cpuidle(void) { - int ret; - - cpuidle_register_driver(&s3c64xx_cpuidle_driver); - - ret = cpuidle_register_device(&s3c64xx_cpuidle_device); - if (ret) { - pr_err("Failed to register cpuidle device: %d\n", ret); - return ret; - } - - return 0; + return cpuidle_register(&s3c64xx_cpuidle_driver, NULL); } device_initcall(s3c64xx_init_cpuidle); diff --git a/arch/arm/mach-s3c64xx/setup-usb-phy.c b/arch/arm/mach-s3c64xx/setup-usb-phy.c index c8174d95339b..ca960bda02fd 100644 --- a/arch/arm/mach-s3c64xx/setup-usb-phy.c +++ b/arch/arm/mach-s3c64xx/setup-usb-phy.c @@ -76,7 +76,7 @@ static int s3c_usb_otgphy_exit(struct platform_device *pdev) int s5p_usb_phy_init(struct platform_device *pdev, int type) { - if (type == S5P_USB_PHY_DEVICE) + if (type == USB_PHY_TYPE_DEVICE) return s3c_usb_otgphy_init(pdev); return -EINVAL; @@ -84,7 +84,7 @@ int s5p_usb_phy_init(struct platform_device *pdev, int type) int s5p_usb_phy_exit(struct platform_device *pdev, int type) { - if (type == S5P_USB_PHY_DEVICE) + if (type == USB_PHY_TYPE_DEVICE) return s3c_usb_otgphy_exit(pdev); return -EINVAL; diff --git a/arch/arm/mach-s5pv210/setup-usb-phy.c b/arch/arm/mach-s5pv210/setup-usb-phy.c index 356a0900af03..b2ee5333f89c 100644 --- a/arch/arm/mach-s5pv210/setup-usb-phy.c +++ b/arch/arm/mach-s5pv210/setup-usb-phy.c @@ -80,7 +80,7 @@ static int s5pv210_usb_otgphy_exit(struct platform_device *pdev) int s5p_usb_phy_init(struct platform_device *pdev, int type) { - if (type == S5P_USB_PHY_DEVICE) + if (type == USB_PHY_TYPE_DEVICE) return s5pv210_usb_otgphy_init(pdev); return -EINVAL; @@ -88,7 +88,7 @@ int s5p_usb_phy_init(struct platform_device *pdev, int type) int s5p_usb_phy_exit(struct platform_device *pdev, int type) { - if (type == S5P_USB_PHY_DEVICE) + if (type == USB_PHY_TYPE_DEVICE) return s5pv210_usb_otgphy_exit(pdev); return -EINVAL; diff --git a/arch/arm/mach-sa1100/Kconfig b/arch/arm/mach-sa1100/Kconfig index ca14dbdcfb22..04f9784ff0ed 100644 --- a/arch/arm/mach-sa1100/Kconfig +++ b/arch/arm/mach-sa1100/Kconfig @@ -4,7 +4,7 @@ menu "SA11x0 Implementations" config SA1100_ASSABET bool "Assabet" - select CPU_FREQ_SA1110 + select ARM_SA1110_CPUFREQ help Say Y here if you are using the Intel(R) StrongARM(R) SA-1110 Microprocessor Development Board (also known as the Assabet). @@ -20,7 +20,7 @@ config ASSABET_NEPONSET config SA1100_CERF bool "CerfBoard" - select CPU_FREQ_SA1110 + select ARM_SA1110_CPUFREQ help The Intrinsyc CerfBoard is based on the StrongARM 1110 (Discontinued). More information is available at: @@ -47,7 +47,7 @@ endchoice config SA1100_COLLIE bool "Sharp Zaurus SL5500" - # FIXME: select CPU_FREQ_SA11x0 + # FIXME: select ARM_SA11x0_CPUFREQ select SHARP_LOCOMO select SHARP_PARAM select SHARP_SCOOP @@ -56,7 +56,7 @@ config SA1100_COLLIE config SA1100_H3100 bool "Compaq iPAQ H3100" - select CPU_FREQ_SA1110 + select ARM_SA1110_CPUFREQ select HTC_EGPIO help Say Y here if you intend to run this kernel on the Compaq iPAQ @@ -67,7 +67,7 @@ config SA1100_H3100 config SA1100_H3600 bool "Compaq iPAQ H3600/H3700" - select CPU_FREQ_SA1110 + select ARM_SA1110_CPUFREQ select HTC_EGPIO help Say Y here if you intend to run this kernel on the Compaq iPAQ @@ -78,7 +78,7 @@ config SA1100_H3600 config SA1100_BADGE4 bool "HP Labs BadgePAD 4" - select CPU_FREQ_SA1100 + select ARM_SA1100_CPUFREQ select SA1111 help Say Y here if you want to build a kernel for the HP Laboratories @@ -86,7 +86,7 @@ config SA1100_BADGE4 config SA1100_JORNADA720 bool "HP Jornada 720" - # FIXME: select CPU_FREQ_SA11x0 + # FIXME: select ARM_SA11x0_CPUFREQ select SA1111 help Say Y here if you want to build a kernel for the HP Jornada 720 @@ -105,14 +105,14 @@ config SA1100_JORNADA720_SSP config SA1100_HACKKIT bool "HackKit Core CPU Board" - select CPU_FREQ_SA1100 + select ARM_SA1100_CPUFREQ help Say Y here to support the HackKit Core CPU Board <http://hackkit.eletztrick.de>; config SA1100_LART bool "LART" - select CPU_FREQ_SA1100 + select ARM_SA1100_CPUFREQ help Say Y here if you are using the Linux Advanced Radio Terminal (also known as the LART). See <http://www.lartmaker.nl/> for @@ -120,7 +120,7 @@ config SA1100_LART config SA1100_NANOENGINE bool "nanoEngine" - select CPU_FREQ_SA1110 + select ARM_SA1110_CPUFREQ select PCI select PCI_NANOENGINE help @@ -130,7 +130,7 @@ config SA1100_NANOENGINE config SA1100_PLEB bool "PLEB" - select CPU_FREQ_SA1100 + select ARM_SA1100_CPUFREQ help Say Y here if you are using version 1 of the Portable Linux Embedded Board (also known as PLEB). @@ -139,7 +139,7 @@ config SA1100_PLEB config SA1100_SHANNON bool "Shannon" - select CPU_FREQ_SA1100 + select ARM_SA1100_CPUFREQ help The Shannon (also known as a Tuxscreen, and also as a IS2630) was a limited edition webphone produced by Philips. The Shannon is a SA1100 @@ -148,7 +148,7 @@ config SA1100_SHANNON config SA1100_SIMPAD bool "Simpad" - select CPU_FREQ_SA1110 + select ARM_SA1110_CPUFREQ help The SIEMENS webpad SIMpad is based on the StrongARM 1110. There are two different versions CL4 and SL4. CL4 has 32MB RAM and 16MB diff --git a/arch/arm/mach-sa1100/Makefile b/arch/arm/mach-sa1100/Makefile index 1aed9e70465d..2732eef48966 100644 --- a/arch/arm/mach-sa1100/Makefile +++ b/arch/arm/mach-sa1100/Makefile @@ -8,9 +8,6 @@ obj-m := obj-n := obj- := -obj-$(CONFIG_CPU_FREQ_SA1100) += cpu-sa1100.o -obj-$(CONFIG_CPU_FREQ_SA1110) += cpu-sa1110.o - # Specific board support obj-$(CONFIG_SA1100_ASSABET) += assabet.o obj-$(CONFIG_ASSABET_NEPONSET) += neponset.o diff --git a/arch/arm/mach-sa1100/cpu-sa1100.c b/arch/arm/mach-sa1100/cpu-sa1100.c deleted file mode 100644 index e8f4d1e19233..000000000000 --- a/arch/arm/mach-sa1100/cpu-sa1100.c +++ /dev/null @@ -1,249 +0,0 @@ -/* - * cpu-sa1100.c: clock scaling for the SA1100 - * - * Copyright (C) 2000 2001, The Delft University of Technology - * - * Authors: - * - Johan Pouwelse (J.A.Pouwelse@its.tudelft.nl): initial version - * - Erik Mouw (J.A.K.Mouw@its.tudelft.nl): - * - major rewrite for linux-2.3.99 - * - rewritten for the more generic power management scheme in - * linux-2.4.5-rmk1 - * - * This software has been developed while working on the LART - * computing board (http://www.lartmaker.nl/), which is - * sponsored by the Mobile Multi-media Communications - * (http://www.mobimedia.org/) and Ubiquitous Communications - * (http://www.ubicom.tudelft.nl/) projects. - * - * The authors can be reached at: - * - * Erik Mouw - * Information and Communication Theory Group - * Faculty of Information Technology and Systems - * Delft University of Technology - * P.O. Box 5031 - * 2600 GA Delft - * The Netherlands - * - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - * - * Theory of operations - * ==================== - * - * Clock scaling can be used to lower the power consumption of the CPU - * core. This will give you a somewhat longer running time. - * - * The SA-1100 has a single register to change the core clock speed: - * - * PPCR 0x90020014 PLL config - * - * However, the DRAM timings are closely related to the core clock - * speed, so we need to change these, too. The used registers are: - * - * MDCNFG 0xA0000000 DRAM config - * MDCAS0 0xA0000004 Access waveform - * MDCAS1 0xA0000008 Access waveform - * MDCAS2 0xA000000C Access waveform - * - * Care must be taken to change the DRAM parameters the correct way, - * because otherwise the DRAM becomes unusable and the kernel will - * crash. - * - * The simple solution to avoid a kernel crash is to put the actual - * clock change in ROM and jump to that code from the kernel. The main - * disadvantage is that the ROM has to be modified, which is not - * possible on all SA-1100 platforms. Another disadvantage is that - * jumping to ROM makes clock switching unnecessary complicated. - * - * The idea behind this driver is that the memory configuration can be - * changed while running from DRAM (even with interrupts turned on!) - * as long as all re-configuration steps yield a valid DRAM - * configuration. The advantages are clear: it will run on all SA-1100 - * platforms, and the code is very simple. - * - * If you really want to understand what is going on in - * sa1100_update_dram_timings(), you'll have to read sections 8.2, - * 9.5.7.3, and 10.2 from the "Intel StrongARM SA-1100 Microprocessor - * Developers Manual" (available for free from Intel). - * - */ - -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/init.h> -#include <linux/cpufreq.h> -#include <linux/io.h> - -#include <asm/cputype.h> - -#include <mach/hardware.h> - -#include "generic.h" - -struct sa1100_dram_regs { - int speed; - u32 mdcnfg; - u32 mdcas0; - u32 mdcas1; - u32 mdcas2; -}; - - -static struct cpufreq_driver sa1100_driver; - -static struct sa1100_dram_regs sa1100_dram_settings[] = { - /*speed, mdcnfg, mdcas0, mdcas1, mdcas2, clock freq */ - { 59000, 0x00dc88a3, 0xcccccccf, 0xfffffffc, 0xffffffff},/* 59.0 MHz */ - { 73700, 0x011490a3, 0xcccccccf, 0xfffffffc, 0xffffffff},/* 73.7 MHz */ - { 88500, 0x014e90a3, 0xcccccccf, 0xfffffffc, 0xffffffff},/* 88.5 MHz */ - {103200, 0x01889923, 0xcccccccf, 0xfffffffc, 0xffffffff},/* 103.2 MHz */ - {118000, 0x01c29923, 0x9999998f, 0xfffffff9, 0xffffffff},/* 118.0 MHz */ - {132700, 0x01fb2123, 0x9999998f, 0xfffffff9, 0xffffffff},/* 132.7 MHz */ - {147500, 0x02352123, 0x3333330f, 0xfffffff3, 0xffffffff},/* 147.5 MHz */ - {162200, 0x026b29a3, 0x38e38e1f, 0xfff8e38e, 0xffffffff},/* 162.2 MHz */ - {176900, 0x02a329a3, 0x71c71c1f, 0xfff1c71c, 0xffffffff},/* 176.9 MHz */ - {191700, 0x02dd31a3, 0xe38e383f, 0xffe38e38, 0xffffffff},/* 191.7 MHz */ - {206400, 0x03153223, 0xc71c703f, 0xffc71c71, 0xffffffff},/* 206.4 MHz */ - {221200, 0x034fba23, 0xc71c703f, 0xffc71c71, 0xffffffff},/* 221.2 MHz */ - {235900, 0x03853a23, 0xe1e1e07f, 0xe1e1e1e1, 0xffffffe1},/* 235.9 MHz */ - {250700, 0x03bf3aa3, 0xc3c3c07f, 0xc3c3c3c3, 0xffffffc3},/* 250.7 MHz */ - {265400, 0x03f7c2a3, 0xc3c3c07f, 0xc3c3c3c3, 0xffffffc3},/* 265.4 MHz */ - {280200, 0x0431c2a3, 0x878780ff, 0x87878787, 0xffffff87},/* 280.2 MHz */ - { 0, 0, 0, 0, 0 } /* last entry */ -}; - -static void sa1100_update_dram_timings(int current_speed, int new_speed) -{ - struct sa1100_dram_regs *settings = sa1100_dram_settings; - - /* find speed */ - while (settings->speed != 0) { - if (new_speed == settings->speed) - break; - - settings++; - } - - if (settings->speed == 0) { - panic("%s: couldn't find dram setting for speed %d\n", - __func__, new_speed); - } - - /* No risk, no fun: run with interrupts on! */ - if (new_speed > current_speed) { - /* We're going FASTER, so first relax the memory - * timings before changing the core frequency - */ - - /* Half the memory access clock */ - MDCNFG |= MDCNFG_CDB2; - - /* The order of these statements IS important, keep 8 - * pulses!! - */ - MDCAS2 = settings->mdcas2; - MDCAS1 = settings->mdcas1; - MDCAS0 = settings->mdcas0; - MDCNFG = settings->mdcnfg; - } else { - /* We're going SLOWER: first decrease the core - * frequency and then tighten the memory settings. - */ - - /* Half the memory access clock */ - MDCNFG |= MDCNFG_CDB2; - - /* The order of these statements IS important, keep 8 - * pulses!! - */ - MDCAS0 = settings->mdcas0; - MDCAS1 = settings->mdcas1; - MDCAS2 = settings->mdcas2; - MDCNFG = settings->mdcnfg; - } -} - -static int sa1100_target(struct cpufreq_policy *policy, - unsigned int target_freq, - unsigned int relation) -{ - unsigned int cur = sa11x0_getspeed(0); - unsigned int new_ppcr; - struct cpufreq_freqs freqs; - - new_ppcr = sa11x0_freq_to_ppcr(target_freq); - switch (relation) { - case CPUFREQ_RELATION_L: - if (sa11x0_ppcr_to_freq(new_ppcr) > policy->max) - new_ppcr--; - break; - case CPUFREQ_RELATION_H: - if ((sa11x0_ppcr_to_freq(new_ppcr) > target_freq) && - (sa11x0_ppcr_to_freq(new_ppcr - 1) >= policy->min)) - new_ppcr--; - break; - } - - freqs.old = cur; - freqs.new = sa11x0_ppcr_to_freq(new_ppcr); - freqs.cpu = 0; - - cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); - - if (freqs.new > cur) - sa1100_update_dram_timings(cur, freqs.new); - - PPCR = new_ppcr; - - if (freqs.new < cur) - sa1100_update_dram_timings(cur, freqs.new); - - cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); - - return 0; -} - -static int __init sa1100_cpu_init(struct cpufreq_policy *policy) -{ - if (policy->cpu != 0) - return -EINVAL; - policy->cur = policy->min = policy->max = sa11x0_getspeed(0); - policy->cpuinfo.min_freq = 59000; - policy->cpuinfo.max_freq = 287000; - policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL; - return 0; -} - -static struct cpufreq_driver sa1100_driver __refdata = { - .flags = CPUFREQ_STICKY, - .verify = sa11x0_verify_speed, - .target = sa1100_target, - .get = sa11x0_getspeed, - .init = sa1100_cpu_init, - .name = "sa1100", -}; - -static int __init sa1100_dram_init(void) -{ - if (cpu_is_sa1100()) - return cpufreq_register_driver(&sa1100_driver); - else - return -ENODEV; -} - -arch_initcall(sa1100_dram_init); diff --git a/arch/arm/mach-sa1100/cpu-sa1110.c b/arch/arm/mach-sa1100/cpu-sa1110.c deleted file mode 100644 index 48c45b0c92bb..000000000000 --- a/arch/arm/mach-sa1100/cpu-sa1110.c +++ /dev/null @@ -1,408 +0,0 @@ -/* - * linux/arch/arm/mach-sa1100/cpu-sa1110.c - * - * Copyright (C) 2001 Russell King - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * Note: there are two erratas that apply to the SA1110 here: - * 7 - SDRAM auto-power-up failure (rev A0) - * 13 - Corruption of internal register reads/writes following - * SDRAM reads (rev A0, B0, B1) - * - * We ignore rev. A0 and B0 devices; I don't think they're worth supporting. - * - * The SDRAM type can be passed on the command line as cpu_sa1110.sdram=type - */ -#include <linux/cpufreq.h> -#include <linux/delay.h> -#include <linux/init.h> -#include <linux/io.h> -#include <linux/kernel.h> -#include <linux/moduleparam.h> -#include <linux/types.h> - -#include <asm/cputype.h> -#include <asm/mach-types.h> - -#include <mach/hardware.h> - -#include "generic.h" - -#undef DEBUG - -struct sdram_params { - const char name[20]; - u_char rows; /* bits */ - u_char cas_latency; /* cycles */ - u_char tck; /* clock cycle time (ns) */ - u_char trcd; /* activate to r/w (ns) */ - u_char trp; /* precharge to activate (ns) */ - u_char twr; /* write recovery time (ns) */ - u_short refresh; /* refresh time for array (us) */ -}; - -struct sdram_info { - u_int mdcnfg; - u_int mdrefr; - u_int mdcas[3]; -}; - -static struct sdram_params sdram_tbl[] __initdata = { - { /* Toshiba TC59SM716 CL2 */ - .name = "TC59SM716-CL2", - .rows = 12, - .tck = 10, - .trcd = 20, - .trp = 20, - .twr = 10, - .refresh = 64000, - .cas_latency = 2, - }, { /* Toshiba TC59SM716 CL3 */ - .name = "TC59SM716-CL3", - .rows = 12, - .tck = 8, - .trcd = 20, - .trp = 20, - .twr = 8, - .refresh = 64000, - .cas_latency = 3, - }, { /* Samsung K4S641632D TC75 */ - .name = "K4S641632D", - .rows = 14, - .tck = 9, - .trcd = 27, - .trp = 20, - .twr = 9, - .refresh = 64000, - .cas_latency = 3, - }, { /* Samsung K4S281632B-1H */ - .name = "K4S281632B-1H", - .rows = 12, - .tck = 10, - .trp = 20, - .twr = 10, - .refresh = 64000, - .cas_latency = 3, - }, { /* Samsung KM416S4030CT */ - .name = "KM416S4030CT", - .rows = 13, - .tck = 8, - .trcd = 24, /* 3 CLKs */ - .trp = 24, /* 3 CLKs */ - .twr = 16, /* Trdl: 2 CLKs */ - .refresh = 64000, - .cas_latency = 3, - }, { /* Winbond W982516AH75L CL3 */ - .name = "W982516AH75L", - .rows = 16, - .tck = 8, - .trcd = 20, - .trp = 20, - .twr = 8, - .refresh = 64000, - .cas_latency = 3, - }, { /* Micron MT48LC8M16A2TG-75 */ - .name = "MT48LC8M16A2TG-75", - .rows = 12, - .tck = 8, - .trcd = 20, - .trp = 20, - .twr = 8, - .refresh = 64000, - .cas_latency = 3, - }, -}; - -static struct sdram_params sdram_params; - -/* - * Given a period in ns and frequency in khz, calculate the number of - * cycles of frequency in period. Note that we round up to the next - * cycle, even if we are only slightly over. - */ -static inline u_int ns_to_cycles(u_int ns, u_int khz) -{ - return (ns * khz + 999999) / 1000000; -} - -/* - * Create the MDCAS register bit pattern. - */ -static inline void set_mdcas(u_int *mdcas, int delayed, u_int rcd) -{ - u_int shift; - - rcd = 2 * rcd - 1; - shift = delayed + 1 + rcd; - - mdcas[0] = (1 << rcd) - 1; - mdcas[0] |= 0x55555555 << shift; - mdcas[1] = mdcas[2] = 0x55555555 << (shift & 1); -} - -static void -sdram_calculate_timing(struct sdram_info *sd, u_int cpu_khz, - struct sdram_params *sdram) -{ - u_int mem_khz, sd_khz, trp, twr; - - mem_khz = cpu_khz / 2; - sd_khz = mem_khz; - - /* - * If SDCLK would invalidate the SDRAM timings, - * run SDCLK at half speed. - * - * CPU steppings prior to B2 must either run the memory at - * half speed or use delayed read latching (errata 13). - */ - if ((ns_to_cycles(sdram->tck, sd_khz) > 1) || - (CPU_REVISION < CPU_SA1110_B2 && sd_khz < 62000)) - sd_khz /= 2; - - sd->mdcnfg = MDCNFG & 0x007f007f; - - twr = ns_to_cycles(sdram->twr, mem_khz); - - /* trp should always be >1 */ - trp = ns_to_cycles(sdram->trp, mem_khz) - 1; - if (trp < 1) - trp = 1; - - sd->mdcnfg |= trp << 8; - sd->mdcnfg |= trp << 24; - sd->mdcnfg |= sdram->cas_latency << 12; - sd->mdcnfg |= sdram->cas_latency << 28; - sd->mdcnfg |= twr << 14; - sd->mdcnfg |= twr << 30; - - sd->mdrefr = MDREFR & 0xffbffff0; - sd->mdrefr |= 7; - - if (sd_khz != mem_khz) - sd->mdrefr |= MDREFR_K1DB2; - - /* initial number of '1's in MDCAS + 1 */ - set_mdcas(sd->mdcas, sd_khz >= 62000, - ns_to_cycles(sdram->trcd, mem_khz)); - -#ifdef DEBUG - printk(KERN_DEBUG "MDCNFG: %08x MDREFR: %08x MDCAS0: %08x MDCAS1: %08x MDCAS2: %08x\n", - sd->mdcnfg, sd->mdrefr, sd->mdcas[0], sd->mdcas[1], - sd->mdcas[2]); -#endif -} - -/* - * Set the SDRAM refresh rate. - */ -static inline void sdram_set_refresh(u_int dri) -{ - MDREFR = (MDREFR & 0xffff000f) | (dri << 4); - (void) MDREFR; -} - -/* - * Update the refresh period. We do this such that we always refresh - * the SDRAMs within their permissible period. The refresh period is - * always a multiple of the memory clock (fixed at cpu_clock / 2). - * - * FIXME: we don't currently take account of burst accesses here, - * but neither do Intels DM nor Angel. - */ -static void -sdram_update_refresh(u_int cpu_khz, struct sdram_params *sdram) -{ - u_int ns_row = (sdram->refresh * 1000) >> sdram->rows; - u_int dri = ns_to_cycles(ns_row, cpu_khz / 2) / 32; - -#ifdef DEBUG - mdelay(250); - printk(KERN_DEBUG "new dri value = %d\n", dri); -#endif - - sdram_set_refresh(dri); -} - -/* - * Ok, set the CPU frequency. - */ -static int sa1110_target(struct cpufreq_policy *policy, - unsigned int target_freq, - unsigned int relation) -{ - struct sdram_params *sdram = &sdram_params; - struct cpufreq_freqs freqs; - struct sdram_info sd; - unsigned long flags; - unsigned int ppcr, unused; - - switch (relation) { - case CPUFREQ_RELATION_L: - ppcr = sa11x0_freq_to_ppcr(target_freq); - if (sa11x0_ppcr_to_freq(ppcr) > policy->max) - ppcr--; - break; - case CPUFREQ_RELATION_H: - ppcr = sa11x0_freq_to_ppcr(target_freq); - if (ppcr && (sa11x0_ppcr_to_freq(ppcr) > target_freq) && - (sa11x0_ppcr_to_freq(ppcr-1) >= policy->min)) - ppcr--; - break; - default: - return -EINVAL; - } - - freqs.old = sa11x0_getspeed(0); - freqs.new = sa11x0_ppcr_to_freq(ppcr); - freqs.cpu = 0; - - sdram_calculate_timing(&sd, freqs.new, sdram); - -#if 0 - /* - * These values are wrong according to the SA1110 documentation - * and errata, but they seem to work. Need to get a storage - * scope on to the SDRAM signals to work out why. - */ - if (policy->max < 147500) { - sd.mdrefr |= MDREFR_K1DB2; - sd.mdcas[0] = 0xaaaaaa7f; - } else { - sd.mdrefr &= ~MDREFR_K1DB2; - sd.mdcas[0] = 0xaaaaaa9f; - } - sd.mdcas[1] = 0xaaaaaaaa; - sd.mdcas[2] = 0xaaaaaaaa; -#endif - - cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); - - /* - * The clock could be going away for some time. Set the SDRAMs - * to refresh rapidly (every 64 memory clock cycles). To get - * through the whole array, we need to wait 262144 mclk cycles. - * We wait 20ms to be safe. - */ - sdram_set_refresh(2); - if (!irqs_disabled()) - msleep(20); - else - mdelay(20); - - /* - * Reprogram the DRAM timings with interrupts disabled, and - * ensure that we are doing this within a complete cache line. - * This means that we won't access SDRAM for the duration of - * the programming. - */ - local_irq_save(flags); - asm("mcr p15, 0, %0, c7, c10, 4" : : "r" (0)); - udelay(10); - __asm__ __volatile__("\n\ - b 2f \n\ - .align 5 \n\ -1: str %3, [%1, #0] @ MDCNFG \n\ - str %4, [%1, #28] @ MDREFR \n\ - str %5, [%1, #4] @ MDCAS0 \n\ - str %6, [%1, #8] @ MDCAS1 \n\ - str %7, [%1, #12] @ MDCAS2 \n\ - str %8, [%2, #0] @ PPCR \n\ - ldr %0, [%1, #0] \n\ - b 3f \n\ -2: b 1b \n\ -3: nop \n\ - nop" - : "=&r" (unused) - : "r" (&MDCNFG), "r" (&PPCR), "0" (sd.mdcnfg), - "r" (sd.mdrefr), "r" (sd.mdcas[0]), - "r" (sd.mdcas[1]), "r" (sd.mdcas[2]), "r" (ppcr)); - local_irq_restore(flags); - - /* - * Now, return the SDRAM refresh back to normal. - */ - sdram_update_refresh(freqs.new, sdram); - - cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); - - return 0; -} - -static int __init sa1110_cpu_init(struct cpufreq_policy *policy) -{ - if (policy->cpu != 0) - return -EINVAL; - policy->cur = policy->min = policy->max = sa11x0_getspeed(0); - policy->cpuinfo.min_freq = 59000; - policy->cpuinfo.max_freq = 287000; - policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL; - return 0; -} - -/* sa1110_driver needs __refdata because it must remain after init registers - * it with cpufreq_register_driver() */ -static struct cpufreq_driver sa1110_driver __refdata = { - .flags = CPUFREQ_STICKY, - .verify = sa11x0_verify_speed, - .target = sa1110_target, - .get = sa11x0_getspeed, - .init = sa1110_cpu_init, - .name = "sa1110", -}; - -static struct sdram_params *sa1110_find_sdram(const char *name) -{ - struct sdram_params *sdram; - - for (sdram = sdram_tbl; sdram < sdram_tbl + ARRAY_SIZE(sdram_tbl); - sdram++) - if (strcmp(name, sdram->name) == 0) - return sdram; - - return NULL; -} - -static char sdram_name[16]; - -static int __init sa1110_clk_init(void) -{ - struct sdram_params *sdram; - const char *name = sdram_name; - - if (!cpu_is_sa1110()) - return -ENODEV; - - if (!name[0]) { - if (machine_is_assabet()) - name = "TC59SM716-CL3"; - if (machine_is_pt_system3()) - name = "K4S641632D"; - if (machine_is_h3100()) - name = "KM416S4030CT"; - if (machine_is_jornada720()) - name = "K4S281632B-1H"; - if (machine_is_nanoengine()) - name = "MT48LC8M16A2TG-75"; - } - - sdram = sa1110_find_sdram(name); - if (sdram) { - printk(KERN_DEBUG "SDRAM: tck: %d trcd: %d trp: %d" - " twr: %d refresh: %d cas_latency: %d\n", - sdram->tck, sdram->trcd, sdram->trp, - sdram->twr, sdram->refresh, sdram->cas_latency); - - memcpy(&sdram_params, sdram, sizeof(sdram_params)); - - return cpufreq_register_driver(&sa1110_driver); - } - - return 0; -} - -module_param_string(sdram, sdram_name, sizeof(sdram_name), 0); -arch_initcall(sa1110_clk_init); diff --git a/arch/arm/mach-sa1100/include/mach/generic.h b/arch/arm/mach-sa1100/include/mach/generic.h new file mode 100644 index 000000000000..665542e0c9e2 --- /dev/null +++ b/arch/arm/mach-sa1100/include/mach/generic.h @@ -0,0 +1 @@ +#include "../../generic.h" diff --git a/arch/arm/mach-shark/core.c b/arch/arm/mach-shark/core.c index b63dec848195..153555724988 100644 --- a/arch/arm/mach-shark/core.c +++ b/arch/arm/mach-shark/core.c @@ -10,6 +10,7 @@ #include <linux/sched.h> #include <linux/serial_8250.h> #include <linux/io.h> +#include <linux/cpu.h> #include <asm/setup.h> #include <asm/mach-types.h> @@ -130,7 +131,7 @@ static void __init shark_timer_init(void) static void shark_init_early(void) { - disable_hlt(); + cpu_idle_poll_ctrl(true); } MACHINE_START(SHARK, "Shark") diff --git a/arch/arm/mach-shmobile/board-armadillo800eva.c b/arch/arm/mach-shmobile/board-armadillo800eva.c index f2ec0777cfbe..881e5c0e41dd 100644 --- a/arch/arm/mach-shmobile/board-armadillo800eva.c +++ b/arch/arm/mach-shmobile/board-armadillo800eva.c @@ -24,6 +24,7 @@ #include <linux/err.h> #include <linux/kernel.h> #include <linux/input.h> +#include <linux/platform_data/st1232_pdata.h> #include <linux/irq.h> #include <linux/platform_device.h> #include <linux/gpio.h> @@ -169,7 +170,7 @@ static int usbhsf_get_id(struct platform_device *pdev) return USBHS_GADGET; } -static void usbhsf_power_ctrl(struct platform_device *pdev, +static int usbhsf_power_ctrl(struct platform_device *pdev, void __iomem *base, int enable) { struct usbhsf_private *priv = usbhsf_get_priv(pdev); @@ -223,6 +224,8 @@ static void usbhsf_power_ctrl(struct platform_device *pdev, clk_disable(priv->pci); /* usb work around */ clk_disable(priv->usb24); /* usb work around */ } + + return 0; } static int usbhsf_get_vbus(struct platform_device *pdev) @@ -239,7 +242,7 @@ static irqreturn_t usbhsf_interrupt(int irq, void *data) return IRQ_HANDLED; } -static void usbhsf_hardware_exit(struct platform_device *pdev) +static int usbhsf_hardware_exit(struct platform_device *pdev) { struct usbhsf_private *priv = usbhsf_get_priv(pdev); @@ -264,6 +267,8 @@ static void usbhsf_hardware_exit(struct platform_device *pdev) priv->usbh_base = NULL; free_irq(IRQ7, pdev); + + return 0; } static int usbhsf_hardware_init(struct platform_device *pdev) @@ -878,10 +883,15 @@ static struct platform_device i2c_gpio_device = { }; /* I2C */ +static struct st1232_pdata st1232_i2c0_pdata = { + .reset_gpio = 166, +}; + static struct i2c_board_info i2c0_devices[] = { { I2C_BOARD_INFO("st1232-ts", 0x55), .irq = evt2irq(0x0340), + .platform_data = &st1232_i2c0_pdata, }, { I2C_BOARD_INFO("wm8978", 0x1a), @@ -1005,7 +1015,6 @@ static void __init eva_init(void) /* Touchscreen */ gpio_request(GPIO_FN_IRQ10, NULL); /* TP_INT */ - gpio_request_one(GPIO_PORT166, GPIOF_OUT_INIT_HIGH, NULL); /* TP_RST_B */ /* GETHER */ gpio_request(GPIO_FN_ET_CRS, NULL); diff --git a/arch/arm/mach-shmobile/board-kzm9g.c b/arch/arm/mach-shmobile/board-kzm9g.c index 7f3a6b7e7b7c..a385f570bbfc 100644 --- a/arch/arm/mach-shmobile/board-kzm9g.c +++ b/arch/arm/mach-shmobile/board-kzm9g.c @@ -155,12 +155,14 @@ static int usbhs_get_vbus(struct platform_device *pdev) return !((1 << 7) & __raw_readw(priv->cr2)); } -static void usbhs_phy_reset(struct platform_device *pdev) +static int usbhs_phy_reset(struct platform_device *pdev) { struct usbhs_private *priv = usbhs_get_priv(pdev); /* init phy */ __raw_writew(0x8a0a, priv->cr2); + + return 0; } static int usbhs_get_id(struct platform_device *pdev) @@ -202,7 +204,7 @@ static int usbhs_hardware_init(struct platform_device *pdev) return 0; } -static void usbhs_hardware_exit(struct platform_device *pdev) +static int usbhs_hardware_exit(struct platform_device *pdev) { struct usbhs_private *priv = usbhs_get_priv(pdev); @@ -210,6 +212,8 @@ static void usbhs_hardware_exit(struct platform_device *pdev) __raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->phy); free_irq(IRQ15, pdev); + + return 0; } static u32 usbhs_pipe_cfg[] = { diff --git a/arch/arm/mach-shmobile/board-mackerel.c b/arch/arm/mach-shmobile/board-mackerel.c index db968a585ff0..979237c18dad 100644 --- a/arch/arm/mach-shmobile/board-mackerel.c +++ b/arch/arm/mach-shmobile/board-mackerel.c @@ -596,12 +596,14 @@ static int usbhs_get_vbus(struct platform_device *pdev) return usbhs_is_connected(usbhs_get_priv(pdev)); } -static void usbhs_phy_reset(struct platform_device *pdev) +static int usbhs_phy_reset(struct platform_device *pdev) { struct usbhs_private *priv = usbhs_get_priv(pdev); /* init phy */ __raw_writew(0x8a0a, priv->usbcrcaddr); + + return 0; } static int usbhs0_get_id(struct platform_device *pdev) @@ -628,11 +630,13 @@ static int usbhs0_hardware_init(struct platform_device *pdev) return 0; } -static void usbhs0_hardware_exit(struct platform_device *pdev) +static int usbhs0_hardware_exit(struct platform_device *pdev) { struct usbhs_private *priv = usbhs_get_priv(pdev); cancel_delayed_work_sync(&priv->work); + + return 0; } static struct usbhs_private usbhs0_private = { @@ -735,7 +739,7 @@ static int usbhs1_hardware_init(struct platform_device *pdev) return 0; } -static void usbhs1_hardware_exit(struct platform_device *pdev) +static int usbhs1_hardware_exit(struct platform_device *pdev) { struct usbhs_private *priv = usbhs_get_priv(pdev); @@ -743,6 +747,8 @@ static void usbhs1_hardware_exit(struct platform_device *pdev) __raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->usbphyaddr); free_irq(IRQ8, pdev); + + return 0; } static int usbhs1_get_id(struct platform_device *pdev) diff --git a/arch/arm/mach-shmobile/cpuidle.c b/arch/arm/mach-shmobile/cpuidle.c index 9e050268cde4..0afeb5c7061c 100644 --- a/arch/arm/mach-shmobile/cpuidle.c +++ b/arch/arm/mach-shmobile/cpuidle.c @@ -16,39 +16,22 @@ #include <asm/cpuidle.h> #include <asm/io.h> -int shmobile_enter_wfi(struct cpuidle_device *dev, struct cpuidle_driver *drv, - int index) -{ - cpu_do_idle(); - return 0; -} - -static struct cpuidle_device shmobile_cpuidle_dev; static struct cpuidle_driver shmobile_cpuidle_default_driver = { .name = "shmobile_cpuidle", .owner = THIS_MODULE, - .en_core_tk_irqen = 1, .states[0] = ARM_CPUIDLE_WFI_STATE, - .states[0].enter = shmobile_enter_wfi, .safe_state_index = 0, /* C1 */ .state_count = 1, }; static struct cpuidle_driver *cpuidle_drv = &shmobile_cpuidle_default_driver; -void shmobile_cpuidle_set_driver(struct cpuidle_driver *drv) +void __init shmobile_cpuidle_set_driver(struct cpuidle_driver *drv) { cpuidle_drv = drv; } -int shmobile_cpuidle_init(void) +int __init shmobile_cpuidle_init(void) { - struct cpuidle_device *dev = &shmobile_cpuidle_dev; - - cpuidle_register_driver(cpuidle_drv); - - dev->state_count = cpuidle_drv->state_count; - cpuidle_register_device(dev); - - return 0; + return cpuidle_register(cpuidle_drv, NULL); } diff --git a/arch/arm/mach-shmobile/include/mach/common.h b/arch/arm/mach-shmobile/include/mach/common.h index e48606d8a2be..362f9b2d2c02 100644 --- a/arch/arm/mach-shmobile/include/mach/common.h +++ b/arch/arm/mach-shmobile/include/mach/common.h @@ -13,9 +13,6 @@ extern int shmobile_clk_init(void); extern void shmobile_handle_irq_intc(struct pt_regs *); extern struct platform_suspend_ops shmobile_suspend_ops; struct cpuidle_driver; -struct cpuidle_device; -extern int shmobile_enter_wfi(struct cpuidle_device *dev, - struct cpuidle_driver *drv, int index); extern void shmobile_cpuidle_set_driver(struct cpuidle_driver *drv); extern void sh7372_init_irq(void); diff --git a/arch/arm/mach-shmobile/pm-sh7372.c b/arch/arm/mach-shmobile/pm-sh7372.c index a0826a48dd08..dec9293bb90d 100644 --- a/arch/arm/mach-shmobile/pm-sh7372.c +++ b/arch/arm/mach-shmobile/pm-sh7372.c @@ -410,11 +410,9 @@ static int sh7372_enter_a4s(struct cpuidle_device *dev, static struct cpuidle_driver sh7372_cpuidle_driver = { .name = "sh7372_cpuidle", .owner = THIS_MODULE, - .en_core_tk_irqen = 1, .state_count = 5, .safe_state_index = 0, /* C1 */ .states[0] = ARM_CPUIDLE_WFI_STATE, - .states[0].enter = shmobile_enter_wfi, .states[1] = { .name = "C2", .desc = "Core Standby Mode", @@ -450,12 +448,12 @@ static struct cpuidle_driver sh7372_cpuidle_driver = { }, }; -static void sh7372_cpuidle_init(void) +static void __init sh7372_cpuidle_init(void) { shmobile_cpuidle_set_driver(&sh7372_cpuidle_driver); } #else -static void sh7372_cpuidle_init(void) {} +static void __init sh7372_cpuidle_init(void) {} #endif #ifdef CONFIG_SUSPEND diff --git a/arch/arm/mach-shmobile/suspend.c b/arch/arm/mach-shmobile/suspend.c index 47d83f7a70b6..5d92b5dd486b 100644 --- a/arch/arm/mach-shmobile/suspend.c +++ b/arch/arm/mach-shmobile/suspend.c @@ -12,6 +12,8 @@ #include <linux/suspend.h> #include <linux/module.h> #include <linux/err.h> +#include <linux/cpu.h> + #include <asm/io.h> #include <asm/system_misc.h> @@ -23,13 +25,13 @@ static int shmobile_suspend_default_enter(suspend_state_t suspend_state) static int shmobile_suspend_begin(suspend_state_t state) { - disable_hlt(); + cpu_idle_poll_ctrl(true); return 0; } static void shmobile_suspend_end(void) { - enable_hlt(); + cpu_idle_poll_ctrl(false); } struct platform_suspend_ops shmobile_suspend_ops = { diff --git a/arch/arm/mach-tegra/Kconfig b/arch/arm/mach-tegra/Kconfig index d1c4893894ce..dbc653ea851c 100644 --- a/arch/arm/mach-tegra/Kconfig +++ b/arch/arm/mach-tegra/Kconfig @@ -18,8 +18,8 @@ config ARCH_TEGRA_2x_SOC select PL310_ERRATA_727915 if CACHE_L2X0 select PL310_ERRATA_769419 if CACHE_L2X0 select USB_ARCH_HAS_EHCI if USB_SUPPORT - select USB_ULPI if USB - select USB_ULPI_VIEWPORT if USB_SUPPORT + select USB_ULPI if USB_PHY + select USB_ULPI_VIEWPORT if USB_PHY help Support for NVIDIA Tegra AP20 and T20 processors, based on the ARM CortexA9MP CPU and the ARM PL310 L2 cache controller @@ -37,8 +37,8 @@ config ARCH_TEGRA_3x_SOC select PINCTRL_TEGRA30 select PL310_ERRATA_769419 if CACHE_L2X0 select USB_ARCH_HAS_EHCI if USB_SUPPORT - select USB_ULPI if USB - select USB_ULPI_VIEWPORT if USB_SUPPORT + select USB_ULPI if USB_PHY + select USB_ULPI_VIEWPORT if USB_PHY help Support for NVIDIA Tegra T30 processor family, based on the ARM CortexA9MP CPU and the ARM PL310 L2 cache controller diff --git a/arch/arm/mach-tegra/Makefile b/arch/arm/mach-tegra/Makefile index f6b46ae2b7f8..09b578f9eb84 100644 --- a/arch/arm/mach-tegra/Makefile +++ b/arch/arm/mach-tegra/Makefile @@ -24,7 +24,6 @@ obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += cpuidle-tegra30.o endif obj-$(CONFIG_SMP) += platsmp.o headsmp.o obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o -obj-$(CONFIG_CPU_FREQ) += cpu-tegra.o obj-$(CONFIG_TEGRA_PCI) += pcie.o obj-$(CONFIG_ARCH_TEGRA_2x_SOC) += board-dt-tegra20.o diff --git a/arch/arm/mach-tegra/cpu-tegra.c b/arch/arm/mach-tegra/cpu-tegra.c deleted file mode 100644 index e3d6e15ff188..000000000000 --- a/arch/arm/mach-tegra/cpu-tegra.c +++ /dev/null @@ -1,293 +0,0 @@ -/* - * arch/arm/mach-tegra/cpu-tegra.c - * - * Copyright (C) 2010 Google, Inc. - * - * Author: - * Colin Cross <ccross@google.com> - * Based on arch/arm/plat-omap/cpu-omap.c, (C) 2005 Nokia Corporation - * - * This software is licensed under the terms of the GNU General Public - * License version 2, as published by the Free Software Foundation, and - * may be copied, distributed, and modified under those terms. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - */ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/types.h> -#include <linux/sched.h> -#include <linux/cpufreq.h> -#include <linux/delay.h> -#include <linux/init.h> -#include <linux/err.h> -#include <linux/clk.h> -#include <linux/io.h> -#include <linux/suspend.h> - -/* Frequency table index must be sequential starting at 0 */ -static struct cpufreq_frequency_table freq_table[] = { - { 0, 216000 }, - { 1, 312000 }, - { 2, 456000 }, - { 3, 608000 }, - { 4, 760000 }, - { 5, 816000 }, - { 6, 912000 }, - { 7, 1000000 }, - { 8, CPUFREQ_TABLE_END }, -}; - -#define NUM_CPUS 2 - -static struct clk *cpu_clk; -static struct clk *pll_x_clk; -static struct clk *pll_p_clk; -static struct clk *emc_clk; - -static unsigned long target_cpu_speed[NUM_CPUS]; -static DEFINE_MUTEX(tegra_cpu_lock); -static bool is_suspended; - -static int tegra_verify_speed(struct cpufreq_policy *policy) -{ - return cpufreq_frequency_table_verify(policy, freq_table); -} - -static unsigned int tegra_getspeed(unsigned int cpu) -{ - unsigned long rate; - - if (cpu >= NUM_CPUS) - return 0; - - rate = clk_get_rate(cpu_clk) / 1000; - return rate; -} - -static int tegra_cpu_clk_set_rate(unsigned long rate) -{ - int ret; - - /* - * Take an extra reference to the main pll so it doesn't turn - * off when we move the cpu off of it - */ - clk_prepare_enable(pll_x_clk); - - ret = clk_set_parent(cpu_clk, pll_p_clk); - if (ret) { - pr_err("Failed to switch cpu to clock pll_p\n"); - goto out; - } - - if (rate == clk_get_rate(pll_p_clk)) - goto out; - - ret = clk_set_rate(pll_x_clk, rate); - if (ret) { - pr_err("Failed to change pll_x to %lu\n", rate); - goto out; - } - - ret = clk_set_parent(cpu_clk, pll_x_clk); - if (ret) { - pr_err("Failed to switch cpu to clock pll_x\n"); - goto out; - } - -out: - clk_disable_unprepare(pll_x_clk); - return ret; -} - -static int tegra_update_cpu_speed(unsigned long rate) -{ - int ret = 0; - struct cpufreq_freqs freqs; - - freqs.old = tegra_getspeed(0); - freqs.new = rate; - - if (freqs.old == freqs.new) - return ret; - - /* - * Vote on memory bus frequency based on cpu frequency - * This sets the minimum frequency, display or avp may request higher - */ - if (rate >= 816000) - clk_set_rate(emc_clk, 600000000); /* cpu 816 MHz, emc max */ - else if (rate >= 456000) - clk_set_rate(emc_clk, 300000000); /* cpu 456 MHz, emc 150Mhz */ - else - clk_set_rate(emc_clk, 100000000); /* emc 50Mhz */ - - for_each_online_cpu(freqs.cpu) - cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); - -#ifdef CONFIG_CPU_FREQ_DEBUG - printk(KERN_DEBUG "cpufreq-tegra: transition: %u --> %u\n", - freqs.old, freqs.new); -#endif - - ret = tegra_cpu_clk_set_rate(freqs.new * 1000); - if (ret) { - pr_err("cpu-tegra: Failed to set cpu frequency to %d kHz\n", - freqs.new); - return ret; - } - - for_each_online_cpu(freqs.cpu) - cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); - - return 0; -} - -static unsigned long tegra_cpu_highest_speed(void) -{ - unsigned long rate = 0; - int i; - - for_each_online_cpu(i) - rate = max(rate, target_cpu_speed[i]); - return rate; -} - -static int tegra_target(struct cpufreq_policy *policy, - unsigned int target_freq, - unsigned int relation) -{ - unsigned int idx; - unsigned int freq; - int ret = 0; - - mutex_lock(&tegra_cpu_lock); - - if (is_suspended) { - ret = -EBUSY; - goto out; - } - - cpufreq_frequency_table_target(policy, freq_table, target_freq, - relation, &idx); - - freq = freq_table[idx].frequency; - - target_cpu_speed[policy->cpu] = freq; - - ret = tegra_update_cpu_speed(tegra_cpu_highest_speed()); - -out: - mutex_unlock(&tegra_cpu_lock); - return ret; -} - -static int tegra_pm_notify(struct notifier_block *nb, unsigned long event, - void *dummy) -{ - mutex_lock(&tegra_cpu_lock); - if (event == PM_SUSPEND_PREPARE) { - is_suspended = true; - pr_info("Tegra cpufreq suspend: setting frequency to %d kHz\n", - freq_table[0].frequency); - tegra_update_cpu_speed(freq_table[0].frequency); - } else if (event == PM_POST_SUSPEND) { - is_suspended = false; - } - mutex_unlock(&tegra_cpu_lock); - - return NOTIFY_OK; -} - -static struct notifier_block tegra_cpu_pm_notifier = { - .notifier_call = tegra_pm_notify, -}; - -static int tegra_cpu_init(struct cpufreq_policy *policy) -{ - if (policy->cpu >= NUM_CPUS) - return -EINVAL; - - clk_prepare_enable(emc_clk); - clk_prepare_enable(cpu_clk); - - cpufreq_frequency_table_cpuinfo(policy, freq_table); - cpufreq_frequency_table_get_attr(freq_table, policy->cpu); - policy->cur = tegra_getspeed(policy->cpu); - target_cpu_speed[policy->cpu] = policy->cur; - - /* FIXME: what's the actual transition time? */ - policy->cpuinfo.transition_latency = 300 * 1000; - - cpumask_copy(policy->cpus, cpu_possible_mask); - - if (policy->cpu == 0) - register_pm_notifier(&tegra_cpu_pm_notifier); - - return 0; -} - -static int tegra_cpu_exit(struct cpufreq_policy *policy) -{ - cpufreq_frequency_table_cpuinfo(policy, freq_table); - clk_disable_unprepare(emc_clk); - return 0; -} - -static struct freq_attr *tegra_cpufreq_attr[] = { - &cpufreq_freq_attr_scaling_available_freqs, - NULL, -}; - -static struct cpufreq_driver tegra_cpufreq_driver = { - .verify = tegra_verify_speed, - .target = tegra_target, - .get = tegra_getspeed, - .init = tegra_cpu_init, - .exit = tegra_cpu_exit, - .name = "tegra", - .attr = tegra_cpufreq_attr, -}; - -static int __init tegra_cpufreq_init(void) -{ - cpu_clk = clk_get_sys(NULL, "cpu"); - if (IS_ERR(cpu_clk)) - return PTR_ERR(cpu_clk); - - pll_x_clk = clk_get_sys(NULL, "pll_x"); - if (IS_ERR(pll_x_clk)) - return PTR_ERR(pll_x_clk); - - pll_p_clk = clk_get_sys(NULL, "pll_p_cclk"); - if (IS_ERR(pll_p_clk)) - return PTR_ERR(pll_p_clk); - - emc_clk = clk_get_sys("cpu", "emc"); - if (IS_ERR(emc_clk)) { - clk_put(cpu_clk); - return PTR_ERR(emc_clk); - } - - return cpufreq_register_driver(&tegra_cpufreq_driver); -} - -static void __exit tegra_cpufreq_exit(void) -{ - cpufreq_unregister_driver(&tegra_cpufreq_driver); - clk_put(emc_clk); - clk_put(cpu_clk); -} - - -MODULE_AUTHOR("Colin Cross <ccross@android.com>"); -MODULE_DESCRIPTION("cpufreq driver for Nvidia Tegra2"); -MODULE_LICENSE("GPL"); -module_init(tegra_cpufreq_init); -module_exit(tegra_cpufreq_exit); diff --git a/arch/arm/mach-tegra/cpuidle-tegra114.c b/arch/arm/mach-tegra/cpuidle-tegra114.c index 0f4e8c483b34..1d1c6023f4a2 100644 --- a/arch/arm/mach-tegra/cpuidle-tegra114.c +++ b/arch/arm/mach-tegra/cpuidle-tegra114.c @@ -23,39 +23,13 @@ static struct cpuidle_driver tegra_idle_driver = { .name = "tegra_idle", .owner = THIS_MODULE, - .en_core_tk_irqen = 1, .state_count = 1, .states = { [0] = ARM_CPUIDLE_WFI_STATE_PWR(600), }, }; -static DEFINE_PER_CPU(struct cpuidle_device, tegra_idle_device); - int __init tegra114_cpuidle_init(void) { - int ret; - unsigned int cpu; - struct cpuidle_device *dev; - struct cpuidle_driver *drv = &tegra_idle_driver; - - ret = cpuidle_register_driver(&tegra_idle_driver); - if (ret) { - pr_err("CPUidle driver registration failed\n"); - return ret; - } - - for_each_possible_cpu(cpu) { - dev = &per_cpu(tegra_idle_device, cpu); - dev->cpu = cpu; - - dev->state_count = drv->state_count; - ret = cpuidle_register_device(dev); - if (ret) { - pr_err("CPU%u: CPUidle device registration failed\n", - cpu); - return ret; - } - } - return 0; + return cpuidle_register(&tegra_idle_driver, NULL); } diff --git a/arch/arm/mach-tegra/cpuidle-tegra20.c b/arch/arm/mach-tegra/cpuidle-tegra20.c index 825ced4f7a40..590ec25855dd 100644 --- a/arch/arm/mach-tegra/cpuidle-tegra20.c +++ b/arch/arm/mach-tegra/cpuidle-tegra20.c @@ -43,32 +43,33 @@ static atomic_t abort_barrier; static int tegra20_idle_lp2_coupled(struct cpuidle_device *dev, struct cpuidle_driver *drv, int index); +#define TEGRA20_MAX_STATES 2 +#else +#define TEGRA20_MAX_STATES 1 #endif -static struct cpuidle_state tegra_idle_states[] = { - [0] = ARM_CPUIDLE_WFI_STATE_PWR(600), -#ifdef CONFIG_PM_SLEEP - [1] = { - .enter = tegra20_idle_lp2_coupled, - .exit_latency = 5000, - .target_residency = 10000, - .power_usage = 0, - .flags = CPUIDLE_FLAG_TIME_VALID | - CPUIDLE_FLAG_COUPLED, - .name = "powered-down", - .desc = "CPU power gated", - }, -#endif -}; - static struct cpuidle_driver tegra_idle_driver = { .name = "tegra_idle", .owner = THIS_MODULE, - .en_core_tk_irqen = 1, + .states = { + ARM_CPUIDLE_WFI_STATE_PWR(600), +#ifdef CONFIG_PM_SLEEP + { + .enter = tegra20_idle_lp2_coupled, + .exit_latency = 5000, + .target_residency = 10000, + .power_usage = 0, + .flags = CPUIDLE_FLAG_TIME_VALID | + CPUIDLE_FLAG_COUPLED, + .name = "powered-down", + .desc = "CPU power gated", + }, +#endif + }, + .state_count = TEGRA20_MAX_STATES, + .safe_state_index = 0, }; -static DEFINE_PER_CPU(struct cpuidle_device, tegra_idle_device); - #ifdef CONFIG_PM_SLEEP #ifdef CONFIG_SMP static void __iomem *pmc = IO_ADDRESS(TEGRA_PMC_BASE); @@ -217,39 +218,8 @@ static int tegra20_idle_lp2_coupled(struct cpuidle_device *dev, int __init tegra20_cpuidle_init(void) { - int ret; - unsigned int cpu; - struct cpuidle_device *dev; - struct cpuidle_driver *drv = &tegra_idle_driver; - #ifdef CONFIG_PM_SLEEP tegra_tear_down_cpu = tegra20_tear_down_cpu; #endif - - drv->state_count = ARRAY_SIZE(tegra_idle_states); - memcpy(drv->states, tegra_idle_states, - drv->state_count * sizeof(drv->states[0])); - - ret = cpuidle_register_driver(&tegra_idle_driver); - if (ret) { - pr_err("CPUidle driver registration failed\n"); - return ret; - } - - for_each_possible_cpu(cpu) { - dev = &per_cpu(tegra_idle_device, cpu); - dev->cpu = cpu; -#ifdef CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED - dev->coupled_cpus = *cpu_possible_mask; -#endif - - dev->state_count = drv->state_count; - ret = cpuidle_register_device(dev); - if (ret) { - pr_err("CPU%u: CPUidle device registration failed\n", - cpu); - return ret; - } - } - return 0; + return cpuidle_register(&tegra_idle_driver, cpu_possible_mask); } diff --git a/arch/arm/mach-tegra/cpuidle-tegra30.c b/arch/arm/mach-tegra/cpuidle-tegra30.c index 8b50cf4ddd6f..36dc2befa9d8 100644 --- a/arch/arm/mach-tegra/cpuidle-tegra30.c +++ b/arch/arm/mach-tegra/cpuidle-tegra30.c @@ -43,7 +43,6 @@ static int tegra30_idle_lp2(struct cpuidle_device *dev, static struct cpuidle_driver tegra_idle_driver = { .name = "tegra_idle", .owner = THIS_MODULE, - .en_core_tk_irqen = 1, #ifdef CONFIG_PM_SLEEP .state_count = 2, #else @@ -65,8 +64,6 @@ static struct cpuidle_driver tegra_idle_driver = { }, }; -static DEFINE_PER_CPU(struct cpuidle_device, tegra_idle_device); - #ifdef CONFIG_PM_SLEEP static bool tegra30_cpu_cluster_power_down(struct cpuidle_device *dev, struct cpuidle_driver *drv, @@ -157,32 +154,8 @@ static int tegra30_idle_lp2(struct cpuidle_device *dev, int __init tegra30_cpuidle_init(void) { - int ret; - unsigned int cpu; - struct cpuidle_device *dev; - struct cpuidle_driver *drv = &tegra_idle_driver; - #ifdef CONFIG_PM_SLEEP tegra_tear_down_cpu = tegra30_tear_down_cpu; #endif - - ret = cpuidle_register_driver(&tegra_idle_driver); - if (ret) { - pr_err("CPUidle driver registration failed\n"); - return ret; - } - - for_each_possible_cpu(cpu) { - dev = &per_cpu(tegra_idle_device, cpu); - dev->cpu = cpu; - - dev->state_count = drv->state_count; - ret = cpuidle_register_device(dev); - if (ret) { - pr_err("CPU%u: CPUidle device registration failed\n", - cpu); - return ret; - } - } - return 0; + return cpuidle_register(&tegra_idle_driver, NULL); } diff --git a/arch/arm/mach-ux500/board-mop500-regulators.c b/arch/arm/mach-ux500/board-mop500-regulators.c index 2a17bc506cff..ff3c9f016591 100644 --- a/arch/arm/mach-ux500/board-mop500-regulators.c +++ b/arch/arm/mach-ux500/board-mop500-regulators.c @@ -5,6 +5,7 @@ * * Authors: Sundar Iyer <sundar.iyer@stericsson.com> * Bengt Jonsson <bengt.g.jonsson@stericsson.com> + * Daniel Willerud <daniel.willerud@stericsson.com> * * MOP500 board specific initialization for regulators */ @@ -12,6 +13,7 @@ #include <linux/regulator/machine.h> #include <linux/regulator/ab8500.h> #include "board-mop500-regulators.h" +#include "id.h" static struct regulator_consumer_supply gpio_en_3v3_consumers[] = { REGULATOR_SUPPLY("vdd33a", "smsc911x.0"), @@ -53,21 +55,37 @@ struct regulator_init_data tps61052_regulator = { }; static struct regulator_consumer_supply ab8500_vaux1_consumers[] = { - /* External displays, connector on board 2v5 power supply */ - REGULATOR_SUPPLY("vaux12v5", "mcde.0"), + /* Main display, u8500 R3 uib */ + REGULATOR_SUPPLY("vddi", "mcde_disp_sony_acx424akp.0"), + /* Main display, u8500 uib and ST uib */ + REGULATOR_SUPPLY("vdd1", "samsung_s6d16d0.0"), + /* Secondary display, ST uib */ + REGULATOR_SUPPLY("vdd1", "samsung_s6d16d0.1"), /* SFH7741 proximity sensor */ REGULATOR_SUPPLY("vcc", "gpio-keys.0"), /* BH1780GLS ambient light sensor */ REGULATOR_SUPPLY("vcc", "2-0029"), /* lsm303dlh accelerometer */ - REGULATOR_SUPPLY("vdd", "3-0018"), + REGULATOR_SUPPLY("vdd", "2-0018"), + /* lsm303dlhc accelerometer */ + REGULATOR_SUPPLY("vdd", "2-0019"), /* lsm303dlh magnetometer */ - REGULATOR_SUPPLY("vdd", "3-001e"), + REGULATOR_SUPPLY("vdd", "2-001e"), /* Rohm BU21013 Touchscreen devices */ REGULATOR_SUPPLY("avdd", "3-005c"), REGULATOR_SUPPLY("avdd", "3-005d"), /* Synaptics RMI4 Touchscreen device */ REGULATOR_SUPPLY("vdd", "3-004b"), + /* L3G4200D Gyroscope device */ + REGULATOR_SUPPLY("vdd", "2-0068"), + /* Ambient light sensor device */ + REGULATOR_SUPPLY("vdd", "3-0029"), + /* Pressure sensor device */ + REGULATOR_SUPPLY("vdd", "2-005c"), + /* Cypress TrueTouch Touchscreen device */ + REGULATOR_SUPPLY("vcpin", "spi8.0"), + /* Camera device */ + REGULATOR_SUPPLY("vaux12v5", "mmio_camera"), }; static struct regulator_consumer_supply ab8500_vaux2_consumers[] = { @@ -75,18 +93,50 @@ static struct regulator_consumer_supply ab8500_vaux2_consumers[] = { REGULATOR_SUPPLY("vmmc", "sdi4"), /* AB8500 audio codec */ REGULATOR_SUPPLY("vcc-N2158", "ab8500-codec.0"), + /* AB8500 accessory detect 1 */ + REGULATOR_SUPPLY("vcc-N2158", "ab8500-acc-det.0"), + /* AB8500 Tv-out device */ + REGULATOR_SUPPLY("vcc-N2158", "mcde_tv_ab8500.4"), + /* AV8100 HDMI device */ + REGULATOR_SUPPLY("vcc-N2158", "av8100_hdmi.3"), }; static struct regulator_consumer_supply ab8500_vaux3_consumers[] = { + REGULATOR_SUPPLY("v-SD-STM", "stm"), /* External MMC slot power */ REGULATOR_SUPPLY("vmmc", "sdi0"), }; +static struct regulator_consumer_supply ab8505_vaux4_consumers[] = { +}; + +static struct regulator_consumer_supply ab8505_vaux5_consumers[] = { +}; + +static struct regulator_consumer_supply ab8505_vaux6_consumers[] = { +}; + +static struct regulator_consumer_supply ab8505_vaux8_consumers[] = { + /* AB8500 audio codec device */ + REGULATOR_SUPPLY("v-aux8", NULL), +}; + +static struct regulator_consumer_supply ab8505_vadc_consumers[] = { + /* Internal general-purpose ADC */ + REGULATOR_SUPPLY("vddadc", "ab8500-gpadc.0"), + /* ADC for charger */ + REGULATOR_SUPPLY("vddadc", "ab8500-charger.0"), +}; + static struct regulator_consumer_supply ab8500_vtvout_consumers[] = { /* TV-out DENC supply */ REGULATOR_SUPPLY("vtvout", "ab8500-denc.0"), /* Internal general-purpose ADC */ REGULATOR_SUPPLY("vddadc", "ab8500-gpadc.0"), + /* ADC for charger */ + REGULATOR_SUPPLY("vddadc", "ab8500-charger.0"), + /* AB8500 Tv-out device */ + REGULATOR_SUPPLY("vtvout", "mcde_tv_ab8500.4"), }; static struct regulator_consumer_supply ab8500_vaud_consumers[] = { @@ -114,77 +164,90 @@ static struct regulator_consumer_supply ab8500_vintcore_consumers[] = { REGULATOR_SUPPLY("v-intcore", NULL), /* USB Transceiver */ REGULATOR_SUPPLY("vddulpivio18", "ab8500-usb.0"), + /* Handled by abx500 clk driver */ + REGULATOR_SUPPLY("v-intcore", "abx500-clk.0"), +}; + +static struct regulator_consumer_supply ab8505_usb_consumers[] = { + /* HS USB OTG physical interface */ + REGULATOR_SUPPLY("v-ape", NULL), }; static struct regulator_consumer_supply ab8500_vana_consumers[] = { - /* External displays, connector on board, 1v8 power supply */ - REGULATOR_SUPPLY("vsmps2", "mcde.0"), + /* DB8500 DSI */ + REGULATOR_SUPPLY("vdddsi1v2", "mcde"), + REGULATOR_SUPPLY("vdddsi1v2", "b2r2_core"), + REGULATOR_SUPPLY("vdddsi1v2", "b2r2_1_core"), + REGULATOR_SUPPLY("vdddsi1v2", "dsilink.0"), + REGULATOR_SUPPLY("vdddsi1v2", "dsilink.1"), + REGULATOR_SUPPLY("vdddsi1v2", "dsilink.2"), + /* DB8500 CSI */ + REGULATOR_SUPPLY("vddcsi1v2", "mmio_camera"), }; /* ab8500 regulator register initialization */ -struct ab8500_regulator_reg_init -ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = { +static struct ab8500_regulator_reg_init ab8500_reg_init[] = { /* * VanaRequestCtrl = HP/LP depending on VxRequest * VextSupply1RequestCtrl = HP/LP depending on VxRequest */ - INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL2, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL2, 0xf0, 0x00), /* * VextSupply2RequestCtrl = HP/LP depending on VxRequest * VextSupply3RequestCtrl = HP/LP depending on VxRequest * Vaux1RequestCtrl = HP/LP depending on VxRequest * Vaux2RequestCtrl = HP/LP depending on VxRequest */ - INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL3, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL3, 0xff, 0x00), /* * Vaux3RequestCtrl = HP/LP depending on VxRequest * SwHPReq = Control through SWValid disabled */ - INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL4, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL4, 0x07, 0x00), /* * VanaSysClkReq1HPValid = disabled * Vaux1SysClkReq1HPValid = disabled * Vaux2SysClkReq1HPValid = disabled * Vaux3SysClkReq1HPValid = disabled */ - INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID1, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID1, 0xe8, 0x00), /* * VextSupply1SysClkReq1HPValid = disabled * VextSupply2SysClkReq1HPValid = disabled * VextSupply3SysClkReq1HPValid = SysClkReq1 controlled */ - INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID2, 0x40), + INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID2, 0x70, 0x40), /* * VanaHwHPReq1Valid = disabled * Vaux1HwHPreq1Valid = disabled * Vaux2HwHPReq1Valid = disabled * Vaux3HwHPReqValid = disabled */ - INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID1, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID1, 0xe8, 0x00), /* * VextSupply1HwHPReq1Valid = disabled * VextSupply2HwHPReq1Valid = disabled * VextSupply3HwHPReq1Valid = disabled */ - INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID2, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID2, 0x07, 0x00), /* * VanaHwHPReq2Valid = disabled * Vaux1HwHPReq2Valid = disabled * Vaux2HwHPReq2Valid = disabled * Vaux3HwHPReq2Valid = disabled */ - INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID1, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID1, 0xe8, 0x00), /* * VextSupply1HwHPReq2Valid = disabled * VextSupply2HwHPReq2Valid = disabled * VextSupply3HwHPReq2Valid = HWReq2 controlled */ - INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID2, 0x04), + INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID2, 0x07, 0x04), /* * VanaSwHPReqValid = disabled * Vaux1SwHPReqValid = disabled */ - INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID1, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID1, 0xa0, 0x00), /* * Vaux2SwHPReqValid = disabled * Vaux3SwHPReqValid = disabled @@ -192,7 +255,7 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = { * VextSupply2SwHPReqValid = disabled * VextSupply3SwHPReqValid = disabled */ - INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID2, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID2, 0x1f, 0x00), /* * SysClkReq2Valid1 = SysClkReq2 controlled * SysClkReq3Valid1 = disabled @@ -202,7 +265,7 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = { * SysClkReq7Valid1 = disabled * SysClkReq8Valid1 = disabled */ - INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID1, 0x2a), + INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID1, 0xfe, 0x2a), /* * SysClkReq2Valid2 = disabled * SysClkReq3Valid2 = disabled @@ -212,7 +275,7 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = { * SysClkReq7Valid2 = disabled * SysClkReq8Valid2 = disabled */ - INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID2, 0x20), + INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID2, 0xfe, 0x20), /* * VTVoutEna = disabled * Vintcore12Ena = disabled @@ -220,66 +283,62 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = { * Vintcore12LP = inactive (HP) * VTVoutLP = inactive (HP) */ - INIT_REGULATOR_REGISTER(AB8500_REGUMISC1, 0x10), + INIT_REGULATOR_REGISTER(AB8500_REGUMISC1, 0xfe, 0x10), /* * VaudioEna = disabled * VdmicEna = disabled * Vamic1Ena = disabled * Vamic2Ena = disabled */ - INIT_REGULATOR_REGISTER(AB8500_VAUDIOSUPPLY, 0x00), + INIT_REGULATOR_REGISTER(AB8500_VAUDIOSUPPLY, 0x1e, 0x00), /* * Vamic1_dzout = high-Z when Vamic1 is disabled * Vamic2_dzout = high-Z when Vamic2 is disabled */ - INIT_REGULATOR_REGISTER(AB8500_REGUCTRL1VAMIC, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUCTRL1VAMIC, 0x03, 0x00), /* - * VPll = Hw controlled + * VPll = Hw controlled (NOTE! PRCMU bits) * VanaRegu = force off */ - INIT_REGULATOR_REGISTER(AB8500_VPLLVANAREGU, 0x02), + INIT_REGULATOR_REGISTER(AB8500_VPLLVANAREGU, 0x0f, 0x02), /* * VrefDDREna = disabled * VrefDDRSleepMode = inactive (no pulldown) */ - INIT_REGULATOR_REGISTER(AB8500_VREFDDR, 0x00), + INIT_REGULATOR_REGISTER(AB8500_VREFDDR, 0x03, 0x00), /* - * VextSupply1Regu = HW control - * VextSupply2Regu = HW control - * VextSupply3Regu = HW control + * VextSupply1Regu = force LP + * VextSupply2Regu = force OFF + * VextSupply3Regu = force HP (-> STBB2=LP and TPS=LP) * ExtSupply2Bypass = ExtSupply12LPn ball is 0 when Ena is 0 * ExtSupply3Bypass = ExtSupply3LPn ball is 0 when Ena is 0 */ - INIT_REGULATOR_REGISTER(AB8500_EXTSUPPLYREGU, 0x2a), + INIT_REGULATOR_REGISTER(AB8500_EXTSUPPLYREGU, 0xff, 0x13), /* * Vaux1Regu = force HP * Vaux2Regu = force off */ - INIT_REGULATOR_REGISTER(AB8500_VAUX12REGU, 0x01), + INIT_REGULATOR_REGISTER(AB8500_VAUX12REGU, 0x0f, 0x01), /* - * Vaux3regu = force off + * Vaux3Regu = force off */ - INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3REGU, 0x00), + INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3REGU, 0x03, 0x00), /* - * Vsmps1 = 1.15V + * Vaux1Sel = 2.8 V */ - INIT_REGULATOR_REGISTER(AB8500_VSMPS1SEL1, 0x24), - /* - * Vaux1Sel = 2.5 V - */ - INIT_REGULATOR_REGISTER(AB8500_VAUX1SEL, 0x08), + INIT_REGULATOR_REGISTER(AB8500_VAUX1SEL, 0x0f, 0x0C), /* * Vaux2Sel = 2.9 V */ - INIT_REGULATOR_REGISTER(AB8500_VAUX2SEL, 0x0d), + INIT_REGULATOR_REGISTER(AB8500_VAUX2SEL, 0x0f, 0x0d), /* * Vaux3Sel = 2.91 V */ - INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3SEL, 0x07), + INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3SEL, 0x07, 0x07), /* * VextSupply12LP = disabled (no LP) */ - INIT_REGULATOR_REGISTER(AB8500_REGUCTRL2SPARE, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUCTRL2SPARE, 0x01, 0x00), /* * Vaux1Disch = short discharge time * Vaux2Disch = short discharge time @@ -288,33 +347,26 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = { * VTVoutDisch = short discharge time * VaudioDisch = short discharge time */ - INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH, 0xfc, 0x00), /* * VanaDisch = short discharge time * VdmicPullDownEna = pulldown disabled when Vdmic is disabled * VdmicDisch = short discharge time */ - INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH2, 0x00), + INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH2, 0x16, 0x00), }; /* AB8500 regulators */ -struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = { +static struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = { /* supplies to the display/camera */ [AB8500_LDO_AUX1] = { .constraints = { .name = "V-DISPLAY", - .min_uV = 2500000, - .max_uV = 2900000, + .min_uV = 2800000, + .max_uV = 3300000, .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | REGULATOR_CHANGE_STATUS, .boot_on = 1, /* display is on at boot */ - /* - * This voltage cannot be disabled right now because - * it is somehow affecting the external MMC - * functionality, though that typically will use - * AUX3. - */ - .always_on = 1, }, .num_consumer_supplies = ARRAY_SIZE(ab8500_vaux1_consumers), .consumer_supplies = ab8500_vaux1_consumers, @@ -326,7 +378,10 @@ struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = { .min_uV = 1100000, .max_uV = 3300000, .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | - REGULATOR_CHANGE_STATUS, + REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_MODE, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_IDLE, }, .num_consumer_supplies = ARRAY_SIZE(ab8500_vaux2_consumers), .consumer_supplies = ab8500_vaux2_consumers, @@ -338,7 +393,10 @@ struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = { .min_uV = 1100000, .max_uV = 3300000, .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | - REGULATOR_CHANGE_STATUS, + REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_MODE, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_IDLE, }, .num_consumer_supplies = ARRAY_SIZE(ab8500_vaux3_consumers), .consumer_supplies = ab8500_vaux3_consumers, @@ -392,18 +450,614 @@ struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = { [AB8500_LDO_INTCORE] = { .constraints = { .name = "V-INTCORE", - .valid_ops_mask = REGULATOR_CHANGE_STATUS, + .min_uV = 1250000, + .max_uV = 1350000, + .input_uV = 1800000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_MODE | + REGULATOR_CHANGE_DRMS, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_IDLE, }, .num_consumer_supplies = ARRAY_SIZE(ab8500_vintcore_consumers), .consumer_supplies = ab8500_vintcore_consumers, }, - /* supply for U8500 CSI/DSI, VANA LDO */ + /* supply for U8500 CSI-DSI, VANA LDO */ [AB8500_LDO_ANA] = { .constraints = { - .name = "V-CSI/DSI", + .name = "V-CSI-DSI", .valid_ops_mask = REGULATOR_CHANGE_STATUS, }, .num_consumer_supplies = ARRAY_SIZE(ab8500_vana_consumers), .consumer_supplies = ab8500_vana_consumers, }, }; + +/* supply for VextSupply3 */ +static struct regulator_consumer_supply ab8500_ext_supply3_consumers[] = { + /* SIM supply for 3 V SIM cards */ + REGULATOR_SUPPLY("vinvsim", "sim-detect.0"), +}; + +/* extended configuration for VextSupply2, only used for HREFP_V20 boards */ +static struct ab8500_ext_regulator_cfg ab8500_ext_supply2 = { + .hwreq = true, +}; + +/* + * AB8500 external regulators + */ +static struct regulator_init_data ab8500_ext_regulators[] = { + /* fixed Vbat supplies VSMPS1_EXT_1V8 */ + [AB8500_EXT_SUPPLY1] = { + .constraints = { + .name = "ab8500-ext-supply1", + .min_uV = 1800000, + .max_uV = 1800000, + .initial_mode = REGULATOR_MODE_IDLE, + .boot_on = 1, + .always_on = 1, + }, + }, + /* fixed Vbat supplies VSMPS2_EXT_1V36 and VSMPS5_EXT_1V15 */ + [AB8500_EXT_SUPPLY2] = { + .constraints = { + .name = "ab8500-ext-supply2", + .min_uV = 1360000, + .max_uV = 1360000, + }, + }, + /* fixed Vbat supplies VSMPS3_EXT_3V4 and VSMPS4_EXT_3V4 */ + [AB8500_EXT_SUPPLY3] = { + .constraints = { + .name = "ab8500-ext-supply3", + .min_uV = 3400000, + .max_uV = 3400000, + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + .boot_on = 1, + }, + .num_consumer_supplies = + ARRAY_SIZE(ab8500_ext_supply3_consumers), + .consumer_supplies = ab8500_ext_supply3_consumers, + }, +}; + +/* ab8505 regulator register initialization */ +static struct ab8500_regulator_reg_init ab8505_reg_init[] = { + /* + * VarmRequestCtrl + * VsmpsCRequestCtrl + * VsmpsARequestCtrl + * VsmpsBRequestCtrl + */ + INIT_REGULATOR_REGISTER(AB8505_REGUREQUESTCTRL1, 0x00, 0x00), + /* + * VsafeRequestCtrl + * VpllRequestCtrl + * VanaRequestCtrl = HP/LP depending on VxRequest + */ + INIT_REGULATOR_REGISTER(AB8505_REGUREQUESTCTRL2, 0x30, 0x00), + /* + * Vaux1RequestCtrl = HP/LP depending on VxRequest + * Vaux2RequestCtrl = HP/LP depending on VxRequest + */ + INIT_REGULATOR_REGISTER(AB8505_REGUREQUESTCTRL3, 0xf0, 0x00), + /* + * Vaux3RequestCtrl = HP/LP depending on VxRequest + * SwHPReq = Control through SWValid disabled + */ + INIT_REGULATOR_REGISTER(AB8505_REGUREQUESTCTRL4, 0x07, 0x00), + /* + * VsmpsASysClkReq1HPValid + * VsmpsBSysClkReq1HPValid + * VsafeSysClkReq1HPValid + * VanaSysClkReq1HPValid = disabled + * VpllSysClkReq1HPValid + * Vaux1SysClkReq1HPValid = disabled + * Vaux2SysClkReq1HPValid = disabled + * Vaux3SysClkReq1HPValid = disabled + */ + INIT_REGULATOR_REGISTER(AB8505_REGUSYSCLKREQ1HPVALID1, 0xe8, 0x00), + /* + * VsmpsCSysClkReq1HPValid + * VarmSysClkReq1HPValid + * VbbSysClkReq1HPValid + * VsmpsMSysClkReq1HPValid + */ + INIT_REGULATOR_REGISTER(AB8505_REGUSYSCLKREQ1HPVALID2, 0x00, 0x00), + /* + * VsmpsAHwHPReq1Valid + * VsmpsBHwHPReq1Valid + * VsafeHwHPReq1Valid + * VanaHwHPReq1Valid = disabled + * VpllHwHPReq1Valid + * Vaux1HwHPreq1Valid = disabled + * Vaux2HwHPReq1Valid = disabled + * Vaux3HwHPReqValid = disabled + */ + INIT_REGULATOR_REGISTER(AB8505_REGUHWHPREQ1VALID1, 0xe8, 0x00), + /* + * VsmpsMHwHPReq1Valid + */ + INIT_REGULATOR_REGISTER(AB8505_REGUHWHPREQ1VALID2, 0x00, 0x00), + /* + * VsmpsAHwHPReq2Valid + * VsmpsBHwHPReq2Valid + * VsafeHwHPReq2Valid + * VanaHwHPReq2Valid = disabled + * VpllHwHPReq2Valid + * Vaux1HwHPReq2Valid = disabled + * Vaux2HwHPReq2Valid = disabled + * Vaux3HwHPReq2Valid = disabled + */ + INIT_REGULATOR_REGISTER(AB8505_REGUHWHPREQ2VALID1, 0xe8, 0x00), + /* + * VsmpsMHwHPReq2Valid + */ + INIT_REGULATOR_REGISTER(AB8505_REGUHWHPREQ2VALID2, 0x00, 0x00), + /** + * VsmpsCSwHPReqValid + * VarmSwHPReqValid + * VsmpsASwHPReqValid + * VsmpsBSwHPReqValid + * VsafeSwHPReqValid + * VanaSwHPReqValid + * VanaSwHPReqValid = disabled + * VpllSwHPReqValid + * Vaux1SwHPReqValid = disabled + */ + INIT_REGULATOR_REGISTER(AB8505_REGUSWHPREQVALID1, 0xa0, 0x00), + /* + * Vaux2SwHPReqValid = disabled + * Vaux3SwHPReqValid = disabled + * VsmpsMSwHPReqValid + */ + INIT_REGULATOR_REGISTER(AB8505_REGUSWHPREQVALID2, 0x03, 0x00), + /* + * SysClkReq2Valid1 = SysClkReq2 controlled + * SysClkReq3Valid1 = disabled + * SysClkReq4Valid1 = SysClkReq4 controlled + */ + INIT_REGULATOR_REGISTER(AB8505_REGUSYSCLKREQVALID1, 0x0e, 0x0a), + /* + * SysClkReq2Valid2 = disabled + * SysClkReq3Valid2 = disabled + * SysClkReq4Valid2 = disabled + */ + INIT_REGULATOR_REGISTER(AB8505_REGUSYSCLKREQVALID2, 0x0e, 0x00), + /* + * Vaux4SwHPReqValid + * Vaux4HwHPReq2Valid + * Vaux4HwHPReq1Valid + * Vaux4SysClkReq1HPValid + */ + INIT_REGULATOR_REGISTER(AB8505_REGUVAUX4REQVALID, 0x00, 0x00), + /* + * VadcEna = disabled + * VintCore12Ena = disabled + * VintCore12Sel = 1.25 V + * VintCore12LP = inactive (HP) + * VadcLP = inactive (HP) + */ + INIT_REGULATOR_REGISTER(AB8505_REGUMISC1, 0xfe, 0x10), + /* + * VaudioEna = disabled + * Vaux8Ena = disabled + * Vamic1Ena = disabled + * Vamic2Ena = disabled + */ + INIT_REGULATOR_REGISTER(AB8505_VAUDIOSUPPLY, 0x1e, 0x00), + /* + * Vamic1_dzout = high-Z when Vamic1 is disabled + * Vamic2_dzout = high-Z when Vamic2 is disabled + */ + INIT_REGULATOR_REGISTER(AB8505_REGUCTRL1VAMIC, 0x03, 0x00), + /* + * VsmpsARegu + * VsmpsASelCtrl + * VsmpsAAutoMode + * VsmpsAPWMMode + */ + INIT_REGULATOR_REGISTER(AB8505_VSMPSAREGU, 0x00, 0x00), + /* + * VsmpsBRegu + * VsmpsBSelCtrl + * VsmpsBAutoMode + * VsmpsBPWMMode + */ + INIT_REGULATOR_REGISTER(AB8505_VSMPSBREGU, 0x00, 0x00), + /* + * VsafeRegu + * VsafeSelCtrl + * VsafeAutoMode + * VsafePWMMode + */ + INIT_REGULATOR_REGISTER(AB8505_VSAFEREGU, 0x00, 0x00), + /* + * VPll = Hw controlled (NOTE! PRCMU bits) + * VanaRegu = force off + */ + INIT_REGULATOR_REGISTER(AB8505_VPLLVANAREGU, 0x0f, 0x02), + /* + * VextSupply1Regu = force OFF (OTP_ExtSupply12LPnPolarity 1) + * VextSupply2Regu = force OFF (OTP_ExtSupply12LPnPolarity 1) + * VextSupply3Regu = force OFF (OTP_ExtSupply3LPnPolarity 0) + * ExtSupply2Bypass = ExtSupply12LPn ball is 0 when Ena is 0 + * ExtSupply3Bypass = ExtSupply3LPn ball is 0 when Ena is 0 + */ + INIT_REGULATOR_REGISTER(AB8505_EXTSUPPLYREGU, 0xff, 0x30), + /* + * Vaux1Regu = force HP + * Vaux2Regu = force off + */ + INIT_REGULATOR_REGISTER(AB8505_VAUX12REGU, 0x0f, 0x01), + /* + * Vaux3Regu = force off + */ + INIT_REGULATOR_REGISTER(AB8505_VRF1VAUX3REGU, 0x03, 0x00), + /* + * VsmpsASel1 + */ + INIT_REGULATOR_REGISTER(AB8505_VSMPSASEL1, 0x00, 0x00), + /* + * VsmpsASel2 + */ + INIT_REGULATOR_REGISTER(AB8505_VSMPSASEL2, 0x00, 0x00), + /* + * VsmpsASel3 + */ + INIT_REGULATOR_REGISTER(AB8505_VSMPSASEL3, 0x00, 0x00), + /* + * VsmpsBSel1 + */ + INIT_REGULATOR_REGISTER(AB8505_VSMPSBSEL1, 0x00, 0x00), + /* + * VsmpsBSel2 + */ + INIT_REGULATOR_REGISTER(AB8505_VSMPSBSEL2, 0x00, 0x00), + /* + * VsmpsBSel3 + */ + INIT_REGULATOR_REGISTER(AB8505_VSMPSBSEL3, 0x00, 0x00), + /* + * VsafeSel1 + */ + INIT_REGULATOR_REGISTER(AB8505_VSAFESEL1, 0x00, 0x00), + /* + * VsafeSel2 + */ + INIT_REGULATOR_REGISTER(AB8505_VSAFESEL2, 0x00, 0x00), + /* + * VsafeSel3 + */ + INIT_REGULATOR_REGISTER(AB8505_VSAFESEL3, 0x00, 0x00), + /* + * Vaux1Sel = 2.8 V + */ + INIT_REGULATOR_REGISTER(AB8505_VAUX1SEL, 0x0f, 0x0C), + /* + * Vaux2Sel = 2.9 V + */ + INIT_REGULATOR_REGISTER(AB8505_VAUX2SEL, 0x0f, 0x0d), + /* + * Vaux3Sel = 2.91 V + */ + INIT_REGULATOR_REGISTER(AB8505_VRF1VAUX3SEL, 0x07, 0x07), + /* + * Vaux4RequestCtrl + */ + INIT_REGULATOR_REGISTER(AB8505_VAUX4REQCTRL, 0x00, 0x00), + /* + * Vaux4Regu + */ + INIT_REGULATOR_REGISTER(AB8505_VAUX4REGU, 0x00, 0x00), + /* + * Vaux4Sel + */ + INIT_REGULATOR_REGISTER(AB8505_VAUX4SEL, 0x00, 0x00), + /* + * Vaux1Disch = short discharge time + * Vaux2Disch = short discharge time + * Vaux3Disch = short discharge time + * Vintcore12Disch = short discharge time + * VTVoutDisch = short discharge time + * VaudioDisch = short discharge time + */ + INIT_REGULATOR_REGISTER(AB8505_REGUCTRLDISCH, 0xfc, 0x00), + /* + * VanaDisch = short discharge time + * Vaux8PullDownEna = pulldown disabled when Vaux8 is disabled + * Vaux8Disch = short discharge time + */ + INIT_REGULATOR_REGISTER(AB8505_REGUCTRLDISCH2, 0x16, 0x00), + /* + * Vaux4Disch = short discharge time + */ + INIT_REGULATOR_REGISTER(AB8505_REGUCTRLDISCH3, 0x01, 0x00), + /* + * Vaux5Sel + * Vaux5LP + * Vaux5Ena + * Vaux5Disch + * Vaux5DisSfst + * Vaux5DisPulld + */ + INIT_REGULATOR_REGISTER(AB8505_CTRLVAUX5, 0x00, 0x00), + /* + * Vaux6Sel + * Vaux6LP + * Vaux6Ena + * Vaux6DisPulld + */ + INIT_REGULATOR_REGISTER(AB8505_CTRLVAUX6, 0x00, 0x00), +}; + +struct regulator_init_data ab8505_regulators[AB8505_NUM_REGULATORS] = { + /* supplies to the display/camera */ + [AB8505_LDO_AUX1] = { + .constraints = { + .name = "V-DISPLAY", + .min_uV = 2800000, + .max_uV = 3300000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS, + .boot_on = 1, /* display is on at boot */ + }, + .num_consumer_supplies = ARRAY_SIZE(ab8500_vaux1_consumers), + .consumer_supplies = ab8500_vaux1_consumers, + }, + /* supplies to the on-board eMMC */ + [AB8505_LDO_AUX2] = { + .constraints = { + .name = "V-eMMC1", + .min_uV = 1100000, + .max_uV = 3300000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_MODE, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_IDLE, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8500_vaux2_consumers), + .consumer_supplies = ab8500_vaux2_consumers, + }, + /* supply for VAUX3, supplies to SDcard slots */ + [AB8505_LDO_AUX3] = { + .constraints = { + .name = "V-MMC-SD", + .min_uV = 1100000, + .max_uV = 3300000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_MODE, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_IDLE, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8500_vaux3_consumers), + .consumer_supplies = ab8500_vaux3_consumers, + }, + /* supply for VAUX4, supplies to NFC and standalone secure element */ + [AB8505_LDO_AUX4] = { + .constraints = { + .name = "V-NFC-SE", + .min_uV = 1100000, + .max_uV = 3300000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_MODE, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_IDLE, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8505_vaux4_consumers), + .consumer_supplies = ab8505_vaux4_consumers, + }, + /* supply for VAUX5, supplies to TBD */ + [AB8505_LDO_AUX5] = { + .constraints = { + .name = "V-AUX5", + .min_uV = 1050000, + .max_uV = 2790000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_MODE, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_IDLE, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8505_vaux5_consumers), + .consumer_supplies = ab8505_vaux5_consumers, + }, + /* supply for VAUX6, supplies to TBD */ + [AB8505_LDO_AUX6] = { + .constraints = { + .name = "V-AUX6", + .min_uV = 1050000, + .max_uV = 2790000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_MODE, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_IDLE, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8505_vaux6_consumers), + .consumer_supplies = ab8505_vaux6_consumers, + }, + /* supply for gpadc, ADC LDO */ + [AB8505_LDO_ADC] = { + .constraints = { + .name = "V-ADC", + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8505_vadc_consumers), + .consumer_supplies = ab8505_vadc_consumers, + }, + /* supply for ab8500-vaudio, VAUDIO LDO */ + [AB8505_LDO_AUDIO] = { + .constraints = { + .name = "V-AUD", + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8500_vaud_consumers), + .consumer_supplies = ab8500_vaud_consumers, + }, + /* supply for v-anamic1 VAMic1-LDO */ + [AB8505_LDO_ANAMIC1] = { + .constraints = { + .name = "V-AMIC1", + .valid_ops_mask = REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_MODE, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_IDLE, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8500_vamic1_consumers), + .consumer_supplies = ab8500_vamic1_consumers, + }, + /* supply for v-amic2, VAMIC2 LDO, reuse constants for AMIC1 */ + [AB8505_LDO_ANAMIC2] = { + .constraints = { + .name = "V-AMIC2", + .valid_ops_mask = REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_MODE, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_IDLE, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8500_vamic2_consumers), + .consumer_supplies = ab8500_vamic2_consumers, + }, + /* supply for v-aux8, VAUX8 LDO */ + [AB8505_LDO_AUX8] = { + .constraints = { + .name = "V-AUX8", + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8505_vaux8_consumers), + .consumer_supplies = ab8505_vaux8_consumers, + }, + /* supply for v-intcore12, VINTCORE12 LDO */ + [AB8505_LDO_INTCORE] = { + .constraints = { + .name = "V-INTCORE", + .min_uV = 1250000, + .max_uV = 1350000, + .input_uV = 1800000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_MODE | + REGULATOR_CHANGE_DRMS, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_IDLE, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8500_vintcore_consumers), + .consumer_supplies = ab8500_vintcore_consumers, + }, + /* supply for LDO USB */ + [AB8505_LDO_USB] = { + .constraints = { + .name = "V-USB", + .valid_ops_mask = REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_MODE, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_IDLE, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8505_usb_consumers), + .consumer_supplies = ab8505_usb_consumers, + }, + /* supply for U8500 CSI-DSI, VANA LDO */ + [AB8505_LDO_ANA] = { + .constraints = { + .name = "V-CSI-DSI", + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(ab8500_vana_consumers), + .consumer_supplies = ab8500_vana_consumers, + }, +}; + +struct ab8500_regulator_platform_data ab8500_regulator_plat_data = { + .reg_init = ab8500_reg_init, + .num_reg_init = ARRAY_SIZE(ab8500_reg_init), + .regulator = ab8500_regulators, + .num_regulator = ARRAY_SIZE(ab8500_regulators), + .ext_regulator = ab8500_ext_regulators, + .num_ext_regulator = ARRAY_SIZE(ab8500_ext_regulators), +}; + +/* Use the AB8500 init settings for AB8505 as they are the same right now */ +struct ab8500_regulator_platform_data ab8505_regulator_plat_data = { + .reg_init = ab8505_reg_init, + .num_reg_init = ARRAY_SIZE(ab8505_reg_init), + .regulator = ab8505_regulators, + .num_regulator = ARRAY_SIZE(ab8505_regulators), +}; + +static void ab8500_modify_reg_init(int id, u8 mask, u8 value) +{ + int i; + + if (cpu_is_u8520()) { + for (i = ARRAY_SIZE(ab8505_reg_init) - 1; i >= 0; i--) { + if (ab8505_reg_init[i].id == id) { + u8 initval = ab8505_reg_init[i].value; + initval = (initval & ~mask) | (value & mask); + ab8505_reg_init[i].value = initval; + + BUG_ON(mask & ~ab8505_reg_init[i].mask); + return; + } + } + } else { + for (i = ARRAY_SIZE(ab8500_reg_init) - 1; i >= 0; i--) { + if (ab8500_reg_init[i].id == id) { + u8 initval = ab8500_reg_init[i].value; + initval = (initval & ~mask) | (value & mask); + ab8500_reg_init[i].value = initval; + + BUG_ON(mask & ~ab8500_reg_init[i].mask); + return; + } + } + } + + BUG_ON(1); +} + +void mop500_regulator_init(void) +{ + struct regulator_init_data *regulator; + + /* + * Temporarily turn on Vaux2 on 8520 machine + */ + if (cpu_is_u8520()) { + /* Vaux2 initialized to be on */ + ab8500_modify_reg_init(AB8505_VAUX12REGU, 0x0f, 0x05); + } + + /* + * Handle AB8500_EXT_SUPPLY2 on HREFP_V20_V50 boards (do it for + * all HREFP_V20 boards) + */ + if (cpu_is_u8500v20()) { + /* VextSupply2RequestCtrl = HP/OFF depending on VxRequest */ + ab8500_modify_reg_init(AB8500_REGUREQUESTCTRL3, 0x01, 0x01); + + /* VextSupply2SysClkReq1HPValid = SysClkReq1 controlled */ + ab8500_modify_reg_init(AB8500_REGUSYSCLKREQ1HPVALID2, + 0x20, 0x20); + + /* VextSupply2 = force HP at initialization */ + ab8500_modify_reg_init(AB8500_EXTSUPPLYREGU, 0x0c, 0x04); + + /* enable VextSupply2 during platform active */ + regulator = &ab8500_ext_regulators[AB8500_EXT_SUPPLY2]; + regulator->constraints.always_on = 1; + + /* disable VextSupply2 in suspend */ + regulator = &ab8500_ext_regulators[AB8500_EXT_SUPPLY2]; + regulator->constraints.state_mem.disabled = 1; + regulator->constraints.state_standby.disabled = 1; + + /* enable VextSupply2 HW control (used in suspend) */ + regulator->driver_data = (void *)&ab8500_ext_supply2; + } +} diff --git a/arch/arm/mach-ux500/board-mop500-regulators.h b/arch/arm/mach-ux500/board-mop500-regulators.h index 78a0642a2206..9bece38fe933 100644 --- a/arch/arm/mach-ux500/board-mop500-regulators.h +++ b/arch/arm/mach-ux500/board-mop500-regulators.h @@ -14,10 +14,11 @@ #include <linux/regulator/machine.h> #include <linux/regulator/ab8500.h> -extern struct ab8500_regulator_reg_init -ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS]; -extern struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS]; +extern struct ab8500_regulator_platform_data ab8500_regulator_plat_data; +extern struct ab8500_regulator_platform_data ab8505_regulator_plat_data; extern struct regulator_init_data tps61052_regulator; extern struct regulator_init_data gpio_en_3v3_regulator; +void mop500_regulator_init(void); + #endif diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c index 87d2d7b38ce9..ce672378a830 100644 --- a/arch/arm/mach-ux500/board-mop500.c +++ b/arch/arm/mach-ux500/board-mop500.c @@ -199,10 +199,7 @@ static struct platform_device snowball_sbnet_dev = { struct ab8500_platform_data ab8500_platdata = { .irq_base = MOP500_AB8500_IRQ_BASE, - .regulator_reg_init = ab8500_regulator_reg_init, - .num_regulator_reg_init = ARRAY_SIZE(ab8500_regulator_reg_init), - .regulator = ab8500_regulators, - .num_regulator = ARRAY_SIZE(ab8500_regulators), + .regulator = &ab8500_regulator_plat_data, .gpio = &ab8500_gpio_pdata, .codec = &ab8500_codec_pdata, }; diff --git a/arch/arm/mach-ux500/cpuidle.c b/arch/arm/mach-ux500/cpuidle.c index ce9149302cc3..488e07472d98 100644 --- a/arch/arm/mach-ux500/cpuidle.c +++ b/arch/arm/mach-ux500/cpuidle.c @@ -11,7 +11,6 @@ #include <linux/module.h> #include <linux/cpuidle.h> -#include <linux/clockchips.h> #include <linux/spinlock.h> #include <linux/atomic.h> #include <linux/smp.h> @@ -22,7 +21,6 @@ static atomic_t master = ATOMIC_INIT(0); static DEFINE_SPINLOCK(master_lock); -static DEFINE_PER_CPU(struct cpuidle_device, ux500_cpuidle_device); static inline int ux500_enter_idle(struct cpuidle_device *dev, struct cpuidle_driver *drv, int index) @@ -30,8 +28,6 @@ static inline int ux500_enter_idle(struct cpuidle_device *dev, int this_cpu = smp_processor_id(); bool recouple = false; - clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &this_cpu); - if (atomic_inc_return(&master) == num_online_cpus()) { /* With this lock, we prevent the other cpu to exit and enter @@ -91,22 +87,20 @@ out: spin_unlock(&master_lock); } - clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT, &this_cpu); - return index; } static struct cpuidle_driver ux500_idle_driver = { .name = "ux500_idle", .owner = THIS_MODULE, - .en_core_tk_irqen = 1, .states = { ARM_CPUIDLE_WFI_STATE, { .enter = ux500_enter_idle, .exit_latency = 70, .target_residency = 260, - .flags = CPUIDLE_FLAG_TIME_VALID, + .flags = CPUIDLE_FLAG_TIME_VALID | + CPUIDLE_FLAG_TIMER_STOP, .name = "ApIdle", .desc = "ARM Retention", }, @@ -115,59 +109,13 @@ static struct cpuidle_driver ux500_idle_driver = { .state_count = 2, }; -/* - * For each cpu, setup the broadcast timer because we will - * need to migrate the timers for the states >= ApIdle. - */ -static void ux500_setup_broadcast_timer(void *arg) -{ - int cpu = smp_processor_id(); - clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ON, &cpu); -} - int __init ux500_idle_init(void) { - int ret, cpu; - struct cpuidle_device *device; - /* Configure wake up reasons */ prcmu_enable_wakeups(PRCMU_WAKEUP(ARM) | PRCMU_WAKEUP(RTC) | PRCMU_WAKEUP(ABB)); - /* - * Configure the timer broadcast for each cpu, that must - * be done from the cpu context, so we use a smp cross - * call with 'on_each_cpu'. - */ - on_each_cpu(ux500_setup_broadcast_timer, NULL, 1); - - ret = cpuidle_register_driver(&ux500_idle_driver); - if (ret) { - printk(KERN_ERR "failed to register ux500 idle driver\n"); - return ret; - } - - for_each_online_cpu(cpu) { - device = &per_cpu(ux500_cpuidle_device, cpu); - device->cpu = cpu; - ret = cpuidle_register_device(device); - if (ret) { - printk(KERN_ERR "Failed to register cpuidle " - "device for cpu%d\n", cpu); - goto out_unregister; - } - } -out: - return ret; - -out_unregister: - for_each_online_cpu(cpu) { - device = &per_cpu(ux500_cpuidle_device, cpu); - cpuidle_unregister_device(device); - } - - cpuidle_unregister_driver(&ux500_idle_driver); - goto out; + return cpuidle_register(&ux500_idle_driver, NULL); } device_initcall(ux500_idle_init); diff --git a/arch/arm/mach-vexpress/Kconfig b/arch/arm/mach-vexpress/Kconfig index 52d315b792c8..0f1c5e53fb27 100644 --- a/arch/arm/mach-vexpress/Kconfig +++ b/arch/arm/mach-vexpress/Kconfig @@ -17,6 +17,9 @@ config ARCH_VEXPRESS select NO_IOPORT select PLAT_VERSATILE select PLAT_VERSATILE_CLCD + select POWER_RESET + select POWER_RESET_VEXPRESS + select POWER_SUPPLY select REGULATOR_FIXED_VOLTAGE if REGULATOR select VEXPRESS_CONFIG help diff --git a/arch/arm/mach-vexpress/Makefile b/arch/arm/mach-vexpress/Makefile index 80b64971fbdd..42703e8b4d3b 100644 --- a/arch/arm/mach-vexpress/Makefile +++ b/arch/arm/mach-vexpress/Makefile @@ -4,7 +4,7 @@ ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include \ -I$(srctree)/arch/arm/plat-versatile/include -obj-y := v2m.o reset.o +obj-y := v2m.o obj-$(CONFIG_ARCH_VEXPRESS_CA9X4) += ct-ca9x4.o obj-$(CONFIG_SMP) += platsmp.o obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o diff --git a/arch/arm/mach-vexpress/reset.c b/arch/arm/mach-vexpress/reset.c deleted file mode 100644 index 465923aa3819..000000000000 --- a/arch/arm/mach-vexpress/reset.c +++ /dev/null @@ -1,141 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Copyright (C) 2012 ARM Limited - */ - -#include <linux/jiffies.h> -#include <linux/of.h> -#include <linux/of_device.h> -#include <linux/platform_device.h> -#include <linux/stat.h> -#include <linux/vexpress.h> - -static void vexpress_reset_do(struct device *dev, const char *what) -{ - int err = -ENOENT; - struct vexpress_config_func *func = - vexpress_config_func_get_by_dev(dev); - - if (func) { - unsigned long timeout; - - err = vexpress_config_write(func, 0, 0); - - timeout = jiffies + HZ; - while (time_before(jiffies, timeout)) - cpu_relax(); - } - - dev_emerg(dev, "Unable to %s (%d)\n", what, err); -} - -static struct device *vexpress_power_off_device; - -void vexpress_power_off(void) -{ - vexpress_reset_do(vexpress_power_off_device, "power off"); -} - -static struct device *vexpress_restart_device; - -void vexpress_restart(char str, const char *cmd) -{ - vexpress_reset_do(vexpress_restart_device, "restart"); -} - -static ssize_t vexpress_reset_active_show(struct device *dev, - struct device_attribute *attr, char *buf) -{ - return sprintf(buf, "%d\n", vexpress_restart_device == dev); -} - -static ssize_t vexpress_reset_active_store(struct device *dev, - struct device_attribute *attr, const char *buf, size_t count) -{ - long value; - int err = kstrtol(buf, 0, &value); - - if (!err && value) - vexpress_restart_device = dev; - - return err ? err : count; -} - -DEVICE_ATTR(active, S_IRUGO | S_IWUSR, vexpress_reset_active_show, - vexpress_reset_active_store); - - -enum vexpress_reset_func { FUNC_RESET, FUNC_SHUTDOWN, FUNC_REBOOT }; - -static struct of_device_id vexpress_reset_of_match[] = { - { - .compatible = "arm,vexpress-reset", - .data = (void *)FUNC_RESET, - }, { - .compatible = "arm,vexpress-shutdown", - .data = (void *)FUNC_SHUTDOWN - }, { - .compatible = "arm,vexpress-reboot", - .data = (void *)FUNC_REBOOT - }, - {} -}; - -static int vexpress_reset_probe(struct platform_device *pdev) -{ - enum vexpress_reset_func func; - const struct of_device_id *match = - of_match_device(vexpress_reset_of_match, &pdev->dev); - - if (match) - func = (enum vexpress_reset_func)match->data; - else - func = pdev->id_entry->driver_data; - - switch (func) { - case FUNC_SHUTDOWN: - vexpress_power_off_device = &pdev->dev; - break; - case FUNC_RESET: - if (!vexpress_restart_device) - vexpress_restart_device = &pdev->dev; - device_create_file(&pdev->dev, &dev_attr_active); - break; - case FUNC_REBOOT: - vexpress_restart_device = &pdev->dev; - device_create_file(&pdev->dev, &dev_attr_active); - break; - }; - - return 0; -} - -static const struct platform_device_id vexpress_reset_id_table[] = { - { .name = "vexpress-reset", .driver_data = FUNC_RESET, }, - { .name = "vexpress-shutdown", .driver_data = FUNC_SHUTDOWN, }, - { .name = "vexpress-reboot", .driver_data = FUNC_REBOOT, }, - {} -}; - -static struct platform_driver vexpress_reset_driver = { - .probe = vexpress_reset_probe, - .driver = { - .name = "vexpress-reset", - .of_match_table = vexpress_reset_of_match, - }, - .id_table = vexpress_reset_id_table, -}; - -static int __init vexpress_reset_init(void) -{ - return platform_driver_register(&vexpress_reset_driver); -} -device_initcall(vexpress_reset_init); diff --git a/arch/arm/mach-vexpress/v2m.c b/arch/arm/mach-vexpress/v2m.c index 915683cb67d6..eb2b3a627f03 100644 --- a/arch/arm/mach-vexpress/v2m.c +++ b/arch/arm/mach-vexpress/v2m.c @@ -21,6 +21,8 @@ #include <linux/regulator/fixed.h> #include <linux/regulator/machine.h> #include <linux/vexpress.h> +#include <linux/clk-provider.h> +#include <linux/clkdev.h> #include <asm/arch_timer.h> #include <asm/mach-types.h> @@ -361,8 +363,6 @@ static void __init v2m_init(void) for (i = 0; i < ARRAY_SIZE(v2m_amba_devs); i++) amba_device_register(v2m_amba_devs[i], &iomem_resource); - pm_power_off = vexpress_power_off; - ct_desc->init_tile(); } @@ -374,7 +374,6 @@ MACHINE_START(VEXPRESS, "ARM-Versatile Express") .init_irq = v2m_init_irq, .init_time = v2m_timer_init, .init_machine = v2m_init, - .restart = vexpress_restart, MACHINE_END static struct map_desc v2m_rs1_io_desc __initdata = { @@ -433,7 +432,7 @@ static void __init v2m_dt_timer_init(void) { struct device_node *node = NULL; - vexpress_clk_of_init(); + of_clk_init(NULL); do { node = of_find_compatible_node(node, NULL, "arm,sp804"); @@ -441,6 +440,10 @@ static void __init v2m_dt_timer_init(void) if (node) { pr_info("Using SP804 '%s' as a clock & events source\n", node->full_name); + WARN_ON(clk_register_clkdev(of_clk_get_by_name(node, + "timclken1"), "v2m-timer0", "sp804")); + WARN_ON(clk_register_clkdev(of_clk_get_by_name(node, + "timclken2"), "v2m-timer1", "sp804")); v2m_sp804_init(of_iomap(node, 0), irq_of_parse_and_map(node, 0)); } @@ -464,7 +467,6 @@ static void __init v2m_dt_init(void) { l2x0_of_init(0x00400000, 0xfe0fffff); of_platform_populate(NULL, v2m_dt_bus_match, NULL, NULL); - pm_power_off = vexpress_power_off; } static const char * const v2m_dt_match[] __initconst = { @@ -481,5 +483,4 @@ DT_MACHINE_START(VEXPRESS_DT, "ARM-Versatile Express") .init_irq = irqchip_init, .init_time = v2m_dt_timer_init, .init_machine = v2m_dt_init, - .restart = vexpress_restart, MACHINE_END diff --git a/arch/arm/mach-w90x900/dev.c b/arch/arm/mach-w90x900/dev.c index 7abdb9645c5b..e65a80a1ac75 100644 --- a/arch/arm/mach-w90x900/dev.c +++ b/arch/arm/mach-w90x900/dev.c @@ -19,6 +19,7 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/slab.h> +#include <linux/cpu.h> #include <linux/mtd/physmap.h> #include <linux/mtd/mtd.h> @@ -531,7 +532,7 @@ static struct platform_device *nuc900_public_dev[] __initdata = { void __init nuc900_board_init(struct platform_device **device, int size) { - disable_hlt(); + cpu_idle_poll_ctrl(true); platform_add_devices(device, size); platform_add_devices(nuc900_public_dev, ARRAY_SIZE(nuc900_public_dev)); spi_register_board_info(nuc900_spi_board_info, diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c index ad722f1208a5..9a5cdc01fcdf 100644 --- a/arch/arm/mm/init.c +++ b/arch/arm/mm/init.c @@ -99,6 +99,9 @@ void show_mem(unsigned int filter) printk("Mem-info:\n"); show_free_areas(filter); + if (filter & SHOW_MEM_FILTER_PAGE_COUNT) + return; + for_each_bank (i, mi) { struct membank *bank = &mi->bank[i]; unsigned int pfn1, pfn2; @@ -424,24 +427,6 @@ void __init bootmem_init(void) max_pfn = max_high - PHYS_PFN_OFFSET; } -static inline int free_area(unsigned long pfn, unsigned long end, char *s) -{ - unsigned int pages = 0, size = (end - pfn) << (PAGE_SHIFT - 10); - - for (; pfn < end; pfn++) { - struct page *page = pfn_to_page(pfn); - ClearPageReserved(page); - init_page_count(page); - __free_page(page); - pages++; - } - - if (size && s) - printk(KERN_INFO "Freeing %s memory: %dK\n", s, size); - - return pages; -} - /* * Poison init memory with an undefined instruction (ARM) or a branch to an * undefined instruction (Thumb). @@ -534,6 +519,14 @@ static void __init free_unused_memmap(struct meminfo *mi) #endif } +#ifdef CONFIG_HIGHMEM +static inline void free_area_high(unsigned long pfn, unsigned long end) +{ + for (; pfn < end; pfn++) + free_highmem_page(pfn_to_page(pfn)); +} +#endif + static void __init free_highpages(void) { #ifdef CONFIG_HIGHMEM @@ -569,8 +562,7 @@ static void __init free_highpages(void) if (res_end > end) res_end = end; if (res_start != start) - totalhigh_pages += free_area(start, res_start, - NULL); + free_area_high(start, res_start); start = res_end; if (start == end) break; @@ -578,9 +570,8 @@ static void __init free_highpages(void) /* And now free anything which remains */ if (start < end) - totalhigh_pages += free_area(start, end, NULL); + free_area_high(start, end); } - totalram_pages += totalhigh_pages; #endif } @@ -609,8 +600,7 @@ void __init mem_init(void) #ifdef CONFIG_SA1111 /* now that our DMA memory is actually so designated, we can free it */ - totalram_pages += free_area(PHYS_PFN_OFFSET, - __phys_to_pfn(__pa(swapper_pg_dir)), NULL); + free_reserved_area(__va(PHYS_PFN_OFFSET), swapper_pg_dir, 0, NULL); #endif free_highpages(); @@ -738,16 +728,12 @@ void free_initmem(void) extern char __tcm_start, __tcm_end; poison_init_mem(&__tcm_start, &__tcm_end - &__tcm_start); - totalram_pages += free_area(__phys_to_pfn(__pa(&__tcm_start)), - __phys_to_pfn(__pa(&__tcm_end)), - "TCM link"); + free_reserved_area(&__tcm_start, &__tcm_end, 0, "TCM link"); #endif poison_init_mem(__init_begin, __init_end - __init_begin); if (!machine_is_integrator() && !machine_is_cintegrator()) - totalram_pages += free_area(__phys_to_pfn(__pa(__init_begin)), - __phys_to_pfn(__pa(__init_end)), - "init"); + free_initmem_default(0); } #ifdef CONFIG_BLK_DEV_INITRD @@ -758,9 +744,7 @@ void free_initrd_mem(unsigned long start, unsigned long end) { if (!keep_initrd) { poison_init_mem((void *)start, PAGE_ALIGN(end) - start); - totalram_pages += free_area(__phys_to_pfn(__pa(start)), - __phys_to_pfn(__pa(end)), - "initrd"); + free_reserved_area(start, end, 0, "initrd"); } } diff --git a/arch/arm/plat-samsung/devs.c b/arch/arm/plat-samsung/devs.c index 51afedda9ab6..03db14d8ace9 100644 --- a/arch/arm/plat-samsung/devs.c +++ b/arch/arm/plat-samsung/devs.c @@ -10,6 +10,7 @@ * published by the Free Software Foundation. */ +#include <linux/amba/pl330.h> #include <linux/kernel.h> #include <linux/types.h> #include <linux/interrupt.h> @@ -1552,6 +1553,9 @@ void __init s3c64xx_spi0_set_platdata(int (*cfg_gpio)(void), int src_clk_nr, pd.num_cs = num_cs; pd.src_clk_nr = src_clk_nr; pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi0_cfg_gpio; +#ifdef CONFIG_PL330_DMA + pd.filter = pl330_filter; +#endif s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi0); } @@ -1590,6 +1594,9 @@ void __init s3c64xx_spi1_set_platdata(int (*cfg_gpio)(void), int src_clk_nr, pd.num_cs = num_cs; pd.src_clk_nr = src_clk_nr; pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi1_cfg_gpio; +#ifdef CONFIG_PL330_DMA + pd.filter = pl330_filter; +#endif s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi1); } @@ -1628,6 +1635,9 @@ void __init s3c64xx_spi2_set_platdata(int (*cfg_gpio)(void), int src_clk_nr, pd.num_cs = num_cs; pd.src_clk_nr = src_clk_nr; pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi2_cfg_gpio; +#ifdef CONFIG_PL330_DMA + pd.filter = pl330_filter; +#endif s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi2); } diff --git a/arch/arm/plat-samsung/include/plat/fb.h b/arch/arm/plat-samsung/include/plat/fb.h index b885322717a1..9ae507270785 100644 --- a/arch/arm/plat-samsung/include/plat/fb.h +++ b/arch/arm/plat-samsung/include/plat/fb.h @@ -15,55 +15,7 @@ #ifndef __PLAT_S3C_FB_H #define __PLAT_S3C_FB_H __FILE__ -/* S3C_FB_MAX_WIN - * Set to the maximum number of windows that any of the supported hardware - * can use. Since the platform data uses this for an array size, having it - * set to the maximum of any version of the hardware can do is safe. - */ -#define S3C_FB_MAX_WIN (5) - -/** - * struct s3c_fb_pd_win - per window setup data - * @xres : The window X size. - * @yres : The window Y size. - * @virtual_x: The virtual X size. - * @virtual_y: The virtual Y size. - */ -struct s3c_fb_pd_win { - unsigned short default_bpp; - unsigned short max_bpp; - unsigned short xres; - unsigned short yres; - unsigned short virtual_x; - unsigned short virtual_y; -}; - -/** - * struct s3c_fb_platdata - S3C driver platform specific information - * @setup_gpio: Setup the external GPIO pins to the right state to transfer - * the data from the display system to the connected display - * device. - * @vidcon0: The base vidcon0 values to control the panel data format. - * @vidcon1: The base vidcon1 values to control the panel data output. - * @vtiming: Video timing when connected to a RGB type panel. - * @win: The setup data for each hardware window, or NULL for unused. - * @display_mode: The LCD output display mode. - * - * The platform data supplies the video driver with all the information - * it requires to work with the display(s) attached to the machine. It - * controls the initial mode, the number of display windows (0 is always - * the base framebuffer) that are initialised etc. - * - */ -struct s3c_fb_platdata { - void (*setup_gpio)(void); - - struct s3c_fb_pd_win *win[S3C_FB_MAX_WIN]; - struct fb_videomode *vtiming; - - u32 vidcon0; - u32 vidcon1; -}; +#include <linux/platform_data/video_s3c.h> /** * s3c_fb_set_platdata() - Setup the FB device with platform data. diff --git a/arch/arm/plat-samsung/include/plat/regs-serial.h b/arch/arm/plat-samsung/include/plat/regs-serial.h index 29c26a818842..f05f2afa440d 100644 --- a/arch/arm/plat-samsung/include/plat/regs-serial.h +++ b/arch/arm/plat-samsung/include/plat/regs-serial.h @@ -1,281 +1 @@ -/* arch/arm/plat-samsung/include/plat/regs-serial.h - * - * From linux/include/asm-arm/hardware/serial_s3c2410.h - * - * Internal header file for Samsung S3C2410 serial ports (UART0-2) - * - * Copyright (C) 2002 Shane Nay (shane@minirl.com) - * - * Additional defines, Copyright 2003 Simtec Electronics (linux@simtec.co.uk) - * - * Adapted from: - * - * Internal header file for MX1ADS serial ports (UART1 & 2) - * - * Copyright (C) 2002 Shane Nay (shane@minirl.com) - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#ifndef __ASM_ARM_REGS_SERIAL_H -#define __ASM_ARM_REGS_SERIAL_H - -#define S3C24XX_VA_UART0 (S3C_VA_UART) -#define S3C24XX_VA_UART1 (S3C_VA_UART + 0x4000 ) -#define S3C24XX_VA_UART2 (S3C_VA_UART + 0x8000 ) -#define S3C24XX_VA_UART3 (S3C_VA_UART + 0xC000 ) - -#define S3C2410_PA_UART0 (S3C24XX_PA_UART) -#define S3C2410_PA_UART1 (S3C24XX_PA_UART + 0x4000 ) -#define S3C2410_PA_UART2 (S3C24XX_PA_UART + 0x8000 ) -#define S3C2443_PA_UART3 (S3C24XX_PA_UART + 0xC000 ) - -#define S3C2410_URXH (0x24) -#define S3C2410_UTXH (0x20) -#define S3C2410_ULCON (0x00) -#define S3C2410_UCON (0x04) -#define S3C2410_UFCON (0x08) -#define S3C2410_UMCON (0x0C) -#define S3C2410_UBRDIV (0x28) -#define S3C2410_UTRSTAT (0x10) -#define S3C2410_UERSTAT (0x14) -#define S3C2410_UFSTAT (0x18) -#define S3C2410_UMSTAT (0x1C) - -#define S3C2410_LCON_CFGMASK ((0xF<<3)|(0x3)) - -#define S3C2410_LCON_CS5 (0x0) -#define S3C2410_LCON_CS6 (0x1) -#define S3C2410_LCON_CS7 (0x2) -#define S3C2410_LCON_CS8 (0x3) -#define S3C2410_LCON_CSMASK (0x3) - -#define S3C2410_LCON_PNONE (0x0) -#define S3C2410_LCON_PEVEN (0x5 << 3) -#define S3C2410_LCON_PODD (0x4 << 3) -#define S3C2410_LCON_PMASK (0x7 << 3) - -#define S3C2410_LCON_STOPB (1<<2) -#define S3C2410_LCON_IRM (1<<6) - -#define S3C2440_UCON_CLKMASK (3<<10) -#define S3C2440_UCON_CLKSHIFT (10) -#define S3C2440_UCON_PCLK (0<<10) -#define S3C2440_UCON_UCLK (1<<10) -#define S3C2440_UCON_PCLK2 (2<<10) -#define S3C2440_UCON_FCLK (3<<10) -#define S3C2443_UCON_EPLL (3<<10) - -#define S3C6400_UCON_CLKMASK (3<<10) -#define S3C6400_UCON_CLKSHIFT (10) -#define S3C6400_UCON_PCLK (0<<10) -#define S3C6400_UCON_PCLK2 (2<<10) -#define S3C6400_UCON_UCLK0 (1<<10) -#define S3C6400_UCON_UCLK1 (3<<10) - -#define S3C2440_UCON2_FCLK_EN (1<<15) -#define S3C2440_UCON0_DIVMASK (15 << 12) -#define S3C2440_UCON1_DIVMASK (15 << 12) -#define S3C2440_UCON2_DIVMASK (7 << 12) -#define S3C2440_UCON_DIVSHIFT (12) - -#define S3C2412_UCON_CLKMASK (3<<10) -#define S3C2412_UCON_CLKSHIFT (10) -#define S3C2412_UCON_UCLK (1<<10) -#define S3C2412_UCON_USYSCLK (3<<10) -#define S3C2412_UCON_PCLK (0<<10) -#define S3C2412_UCON_PCLK2 (2<<10) - -#define S3C2410_UCON_CLKMASK (1 << 10) -#define S3C2410_UCON_CLKSHIFT (10) -#define S3C2410_UCON_UCLK (1<<10) -#define S3C2410_UCON_SBREAK (1<<4) - -#define S3C2410_UCON_TXILEVEL (1<<9) -#define S3C2410_UCON_RXILEVEL (1<<8) -#define S3C2410_UCON_TXIRQMODE (1<<2) -#define S3C2410_UCON_RXIRQMODE (1<<0) -#define S3C2410_UCON_RXFIFO_TOI (1<<7) -#define S3C2443_UCON_RXERR_IRQEN (1<<6) -#define S3C2443_UCON_LOOPBACK (1<<5) - -#define S3C2410_UCON_DEFAULT (S3C2410_UCON_TXILEVEL | \ - S3C2410_UCON_RXILEVEL | \ - S3C2410_UCON_TXIRQMODE | \ - S3C2410_UCON_RXIRQMODE | \ - S3C2410_UCON_RXFIFO_TOI) - -#define S3C2410_UFCON_FIFOMODE (1<<0) -#define S3C2410_UFCON_TXTRIG0 (0<<6) -#define S3C2410_UFCON_RXTRIG8 (1<<4) -#define S3C2410_UFCON_RXTRIG12 (2<<4) - -/* S3C2440 FIFO trigger levels */ -#define S3C2440_UFCON_RXTRIG1 (0<<4) -#define S3C2440_UFCON_RXTRIG8 (1<<4) -#define S3C2440_UFCON_RXTRIG16 (2<<4) -#define S3C2440_UFCON_RXTRIG32 (3<<4) - -#define S3C2440_UFCON_TXTRIG0 (0<<6) -#define S3C2440_UFCON_TXTRIG16 (1<<6) -#define S3C2440_UFCON_TXTRIG32 (2<<6) -#define S3C2440_UFCON_TXTRIG48 (3<<6) - -#define S3C2410_UFCON_RESETBOTH (3<<1) -#define S3C2410_UFCON_RESETTX (1<<2) -#define S3C2410_UFCON_RESETRX (1<<1) - -#define S3C2410_UFCON_DEFAULT (S3C2410_UFCON_FIFOMODE | \ - S3C2410_UFCON_TXTRIG0 | \ - S3C2410_UFCON_RXTRIG8 ) - -#define S3C2410_UMCOM_AFC (1<<4) -#define S3C2410_UMCOM_RTS_LOW (1<<0) - -#define S3C2412_UMCON_AFC_63 (0<<5) /* same as s3c2443 */ -#define S3C2412_UMCON_AFC_56 (1<<5) -#define S3C2412_UMCON_AFC_48 (2<<5) -#define S3C2412_UMCON_AFC_40 (3<<5) -#define S3C2412_UMCON_AFC_32 (4<<5) -#define S3C2412_UMCON_AFC_24 (5<<5) -#define S3C2412_UMCON_AFC_16 (6<<5) -#define S3C2412_UMCON_AFC_8 (7<<5) - -#define S3C2410_UFSTAT_TXFULL (1<<9) -#define S3C2410_UFSTAT_RXFULL (1<<8) -#define S3C2410_UFSTAT_TXMASK (15<<4) -#define S3C2410_UFSTAT_TXSHIFT (4) -#define S3C2410_UFSTAT_RXMASK (15<<0) -#define S3C2410_UFSTAT_RXSHIFT (0) - -/* UFSTAT S3C2443 same as S3C2440 */ -#define S3C2440_UFSTAT_TXFULL (1<<14) -#define S3C2440_UFSTAT_RXFULL (1<<6) -#define S3C2440_UFSTAT_TXSHIFT (8) -#define S3C2440_UFSTAT_RXSHIFT (0) -#define S3C2440_UFSTAT_TXMASK (63<<8) -#define S3C2440_UFSTAT_RXMASK (63) - -#define S3C2410_UTRSTAT_TXE (1<<2) -#define S3C2410_UTRSTAT_TXFE (1<<1) -#define S3C2410_UTRSTAT_RXDR (1<<0) - -#define S3C2410_UERSTAT_OVERRUN (1<<0) -#define S3C2410_UERSTAT_FRAME (1<<2) -#define S3C2410_UERSTAT_BREAK (1<<3) -#define S3C2443_UERSTAT_PARITY (1<<1) - -#define S3C2410_UERSTAT_ANY (S3C2410_UERSTAT_OVERRUN | \ - S3C2410_UERSTAT_FRAME | \ - S3C2410_UERSTAT_BREAK) - -#define S3C2410_UMSTAT_CTS (1<<0) -#define S3C2410_UMSTAT_DeltaCTS (1<<2) - -#define S3C2443_DIVSLOT (0x2C) - -/* S3C64XX interrupt registers. */ -#define S3C64XX_UINTP 0x30 -#define S3C64XX_UINTSP 0x34 -#define S3C64XX_UINTM 0x38 - -#define S3C64XX_UINTM_RXD (0) -#define S3C64XX_UINTM_TXD (2) -#define S3C64XX_UINTM_RXD_MSK (1 << S3C64XX_UINTM_RXD) -#define S3C64XX_UINTM_TXD_MSK (1 << S3C64XX_UINTM_TXD) - -/* Following are specific to S5PV210 */ -#define S5PV210_UCON_CLKMASK (1<<10) -#define S5PV210_UCON_CLKSHIFT (10) -#define S5PV210_UCON_PCLK (0<<10) -#define S5PV210_UCON_UCLK (1<<10) - -#define S5PV210_UFCON_TXTRIG0 (0<<8) -#define S5PV210_UFCON_TXTRIG4 (1<<8) -#define S5PV210_UFCON_TXTRIG8 (2<<8) -#define S5PV210_UFCON_TXTRIG16 (3<<8) -#define S5PV210_UFCON_TXTRIG32 (4<<8) -#define S5PV210_UFCON_TXTRIG64 (5<<8) -#define S5PV210_UFCON_TXTRIG128 (6<<8) -#define S5PV210_UFCON_TXTRIG256 (7<<8) - -#define S5PV210_UFCON_RXTRIG1 (0<<4) -#define S5PV210_UFCON_RXTRIG4 (1<<4) -#define S5PV210_UFCON_RXTRIG8 (2<<4) -#define S5PV210_UFCON_RXTRIG16 (3<<4) -#define S5PV210_UFCON_RXTRIG32 (4<<4) -#define S5PV210_UFCON_RXTRIG64 (5<<4) -#define S5PV210_UFCON_RXTRIG128 (6<<4) -#define S5PV210_UFCON_RXTRIG256 (7<<4) - -#define S5PV210_UFSTAT_TXFULL (1<<24) -#define S5PV210_UFSTAT_RXFULL (1<<8) -#define S5PV210_UFSTAT_TXMASK (255<<16) -#define S5PV210_UFSTAT_TXSHIFT (16) -#define S5PV210_UFSTAT_RXMASK (255<<0) -#define S5PV210_UFSTAT_RXSHIFT (0) - -#define S3C2410_UCON_CLKSEL0 (1 << 0) -#define S3C2410_UCON_CLKSEL1 (1 << 1) -#define S3C2410_UCON_CLKSEL2 (1 << 2) -#define S3C2410_UCON_CLKSEL3 (1 << 3) - -/* Default values for s5pv210 UCON and UFCON uart registers */ -#define S5PV210_UCON_DEFAULT (S3C2410_UCON_TXILEVEL | \ - S3C2410_UCON_RXILEVEL | \ - S3C2410_UCON_TXIRQMODE | \ - S3C2410_UCON_RXIRQMODE | \ - S3C2410_UCON_RXFIFO_TOI | \ - S3C2443_UCON_RXERR_IRQEN) - -#define S5PV210_UFCON_DEFAULT (S3C2410_UFCON_FIFOMODE | \ - S5PV210_UFCON_TXTRIG4 | \ - S5PV210_UFCON_RXTRIG4) - -#ifndef __ASSEMBLY__ - -/* configuration structure for per-machine configurations for the - * serial port - * - * the pointer is setup by the machine specific initialisation from the - * arch/arm/mach-s3c2410/ directory. -*/ - -struct s3c2410_uartcfg { - unsigned char hwport; /* hardware port number */ - unsigned char unused; - unsigned short flags; - upf_t uart_flags; /* default uart flags */ - unsigned int clk_sel; - - unsigned int has_fracval; - - unsigned long ucon; /* value of ucon for port */ - unsigned long ulcon; /* value of ulcon for port */ - unsigned long ufcon; /* value of ufcon for port */ -}; - -/* s3c24xx_uart_devs - * - * this is exported from the core as we cannot use driver_register(), - * or platform_add_device() before the console_initcall() -*/ - -extern struct platform_device *s3c24xx_uart_devs[4]; - -#endif /* __ASSEMBLY__ */ - -#endif /* __ASM_ARM_REGS_SERIAL_H */ - +#include <linux/serial_s3c.h> diff --git a/arch/arm/plat-samsung/include/plat/usb-phy.h b/arch/arm/plat-samsung/include/plat/usb-phy.h index 959bcdb03a25..ab34dfadb7f9 100644 --- a/arch/arm/plat-samsung/include/plat/usb-phy.h +++ b/arch/arm/plat-samsung/include/plat/usb-phy.h @@ -11,10 +11,7 @@ #ifndef __PLAT_SAMSUNG_USB_PHY_H #define __PLAT_SAMSUNG_USB_PHY_H __FILE__ -enum s5p_usb_phy_type { - S5P_USB_PHY_DEVICE, - S5P_USB_PHY_HOST, -}; +#include <linux/usb/samsung_usb_phy.h> extern int s5p_usb_phy_init(struct platform_device *pdev, int type); extern int s5p_usb_phy_exit(struct platform_device *pdev, int type); |