diff options
Diffstat (limited to 'arch/arm')
636 files changed, 16711 insertions, 7586 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index a7f8e7f4b88f..483d2858e367 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -8,8 +8,10 @@ config ARM select ARCH_HAS_DEVMEM_IS_ALLOWED select ARCH_HAS_ELF_RANDOMIZE select ARCH_HAS_FORTIFY_SOURCE - select ARCH_HAS_SET_MEMORY + select ARCH_HAS_KCOV + select ARCH_HAS_PTE_SPECIAL if ARM_LPAE select ARCH_HAS_PHYS_TO_DMA + select ARCH_HAS_SET_MEMORY select ARCH_HAS_STRICT_KERNEL_RWX if MMU && !XIP_KERNEL select ARCH_HAS_STRICT_MODULE_RWX if MMU select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST @@ -56,11 +58,9 @@ config ARM select HAVE_ARCH_TRACEHOOK select HAVE_ARM_SMCCC if CPU_V7 select HAVE_EBPF_JIT if !CPU_ENDIAN_BE32 - select HAVE_CC_STACKPROTECTOR select HAVE_CONTEXT_TRACKING select HAVE_C_RECORDMCOUNT select HAVE_DEBUG_KMEMLEAK - select HAVE_DMA_API_DEBUG select HAVE_DMA_CONTIGUOUS if MMU select HAVE_DYNAMIC_FTRACE if (!XIP_KERNEL) && !CPU_ENDIAN_BE32 && MMU select HAVE_DYNAMIC_FTRACE_WITH_REGS if HAVE_DYNAMIC_FTRACE @@ -91,11 +91,14 @@ config ARM select HAVE_PERF_USER_STACK_DUMP select HAVE_RCU_TABLE_FREE if (SMP && ARM_LPAE) select HAVE_REGS_AND_STACK_ACCESS_API + select HAVE_RSEQ + select HAVE_STACKPROTECTOR select HAVE_SYSCALL_TRACEPOINTS select HAVE_UID16 select HAVE_VIRT_CPU_ACCOUNTING_GEN select IRQ_FORCED_THREADING select MODULES_USE_ELF_REL + select NEED_DMA_MAP_STATE select NO_BOOTMEM select OF_EARLY_FLATTREE if OF select OF_RESERVED_MEM if OF @@ -119,9 +122,6 @@ config ARM_HAS_SG_CHAIN select ARCH_HAS_SG_CHAIN bool -config NEED_SG_DMA_LENGTH - bool - config ARM_DMA_USE_IOMMU bool select ARM_HAS_SG_CHAIN @@ -224,9 +224,6 @@ config ARCH_MAY_HAVE_PC_FDC config ZONE_DMA bool -config NEED_DMA_MAP_STATE - def_bool y - config ARCH_SUPPORTS_UPROBES def_bool y @@ -1467,7 +1464,7 @@ config ARM_PSCI config ARCH_NR_GPIO int default 2048 if ARCH_SOCFPGA - default 1024 if ARCH_BRCMSTB || ARCH_SHMOBILE || ARCH_TEGRA || \ + default 1024 if ARCH_BRCMSTB || ARCH_RENESAS || ARCH_TEGRA || \ ARCH_ZYNQ default 512 if ARCH_EXYNOS || ARCH_KEYSTONE || SOC_OMAP5 || \ SOC_DRA7XX || ARCH_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210 @@ -1704,6 +1701,7 @@ config ARCH_WANT_GENERAL_HUGETLB config ARM_MODULE_PLTS bool "Use PLTs to allow module memory to spill over into vmalloc area" depends on MODULES + default y help Allocate PLTs when loading modules so that jumps and calls whose targets are too far away for their relative offsets to be encoded @@ -1714,7 +1712,8 @@ config ARM_MODULE_PLTS rounding up to page size, the actual memory footprint is usually the same. - Say y if you are getting out of memory errors while loading modules + Disabling this is usually safe for small single-platform + configurations. If unsure, say y. source "mm/Kconfig" @@ -1778,12 +1777,6 @@ config SECCOMP and the task is only allowed to execute a few safe syscalls defined by each seccomp mode. -config SWIOTLB - def_bool y - -config IOMMU_HELPER - def_bool SWIOTLB - config PARAVIRT bool "Enable paravirtualization code" help @@ -1815,6 +1808,7 @@ config XEN depends on MMU select ARCH_DMA_ADDR_T_64BIT select ARM_PSCI + select SWIOTLB select SWIOTLB_XEN select PARAVIRT help diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index 199ebc1c4538..693f84392f1b 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -942,6 +942,13 @@ choice via SCIF0 on Renesas RZ/G1M (R8A7743), R-Car H2 (R8A7790), M2-W (R8A7791), V2H (R8A7792), or M2-N (R8A7793). + config DEBUG_RCAR_GEN2_SCIF1 + bool "Kernel low-level debugging messages via SCIF1 on R8A77470" + depends on ARCH_R8A77470 + help + Say Y here if you want kernel low-level debugging support + via SCIF1 on Renesas RZ/G1C (R8A77470). + config DEBUG_RCAR_GEN2_SCIF2 bool "Kernel low-level debugging messages via SCIF2 on R8A7794" depends on ARCH_R8A7794 @@ -1495,6 +1502,7 @@ config DEBUG_LL_INCLUDE default "debug/renesas-scif.S" if DEBUG_RCAR_GEN1_SCIF0 default "debug/renesas-scif.S" if DEBUG_RCAR_GEN1_SCIF2 default "debug/renesas-scif.S" if DEBUG_RCAR_GEN2_SCIF0 + default "debug/renesas-scif.S" if DEBUG_RCAR_GEN2_SCIF1 default "debug/renesas-scif.S" if DEBUG_RCAR_GEN2_SCIF2 default "debug/renesas-scif.S" if DEBUG_RCAR_GEN2_SCIF4 default "debug/renesas-scif.S" if DEBUG_RMOBILE_SCIFA0 @@ -1617,6 +1625,7 @@ config DEBUG_UART_PHYS default 0xe6c80000 if DEBUG_RMOBILE_SCIFA4 default 0xe6e58000 if DEBUG_RCAR_GEN2_SCIF2 default 0xe6e60000 if DEBUG_RCAR_GEN2_SCIF0 + default 0xe6e68000 if DEBUG_RCAR_GEN2_SCIF1 default 0xe6ee0000 if DEBUG_RCAR_GEN2_SCIF4 default 0xe8008000 if DEBUG_R7S72100_SCIF2 default 0xf0000be0 if ARCH_EBSA110 @@ -1651,8 +1660,8 @@ config DEBUG_UART_PHYS DEBUG_NETX_UART || \ DEBUG_QCOM_UARTDM || DEBUG_R7S72100_SCIF2 || \ DEBUG_RCAR_GEN1_SCIF0 || DEBUG_RCAR_GEN1_SCIF2 || \ - DEBUG_RCAR_GEN2_SCIF0 || DEBUG_RCAR_GEN2_SCIF2 || \ - DEBUG_RCAR_GEN2_SCIF4 || \ + DEBUG_RCAR_GEN2_SCIF0 || DEBUG_RCAR_GEN2_SCIF1 || \ + DEBUG_RCAR_GEN2_SCIF2 || DEBUG_RCAR_GEN2_SCIF4 || \ DEBUG_RMOBILE_SCIFA0 || DEBUG_RMOBILE_SCIFA1 || \ DEBUG_RMOBILE_SCIFA4 || DEBUG_S3C24XX_UART || \ DEBUG_S3C64XX_UART || \ diff --git a/arch/arm/Makefile b/arch/arm/Makefile index e4e537f27339..fc26c3d7b9b6 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -106,7 +106,7 @@ tune-$(CONFIG_CPU_V6K) =$(call cc-option,-mtune=arm1136j-s,-mtune=strongarm) tune-y := $(tune-y) ifeq ($(CONFIG_AEABI),y) -CFLAGS_ABI :=-mabi=aapcs-linux -mno-thumb-interwork -mfpu=vfp +CFLAGS_ABI :=-mabi=aapcs-linux -mfpu=vfp else CFLAGS_ABI :=$(call cc-option,-mapcs-32,-mabi=apcs-gnu) $(call cc-option,-mno-thumb-interwork,) endif @@ -135,7 +135,7 @@ endif KBUILD_CFLAGS +=$(CFLAGS_ABI) $(CFLAGS_ISA) $(arch-y) $(tune-y) $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) -msoft-float -Uarm KBUILD_AFLAGS +=$(CFLAGS_ABI) $(AFLAGS_ISA) $(arch-y) $(tune-y) -include asm/unified.h -msoft-float -CHECKFLAGS += -D__arm__ -m32 +CHECKFLAGS += -D__arm__ #Default value head-y := arch/arm/kernel/head$(MMUEXT).o @@ -212,7 +212,7 @@ machine-$(CONFIG_ARCH_S3C24XX) += s3c24xx machine-$(CONFIG_ARCH_S3C64XX) += s3c64xx machine-$(CONFIG_ARCH_S5PV210) += s5pv210 machine-$(CONFIG_ARCH_SA1100) += sa1100 -machine-$(CONFIG_ARCH_SHMOBILE) += shmobile +machine-$(CONFIG_ARCH_RENESAS) += shmobile machine-$(CONFIG_ARCH_SIRF) += prima2 machine-$(CONFIG_ARCH_SOCFPGA) += socfpga machine-$(CONFIG_ARCH_STI) += sti diff --git a/arch/arm/boot/compressed/Makefile b/arch/arm/boot/compressed/Makefile index 45a6b9b7af2a..1f5a5ffe7fcf 100644 --- a/arch/arm/boot/compressed/Makefile +++ b/arch/arm/boot/compressed/Makefile @@ -25,6 +25,9 @@ endif GCOV_PROFILE := n +# Prevents link failures: __sanitizer_cov_trace_pc() is not linked in. +KCOV_INSTRUMENT := n + # # Architecture dependencies # @@ -113,15 +116,13 @@ CFLAGS_fdt_ro.o := $(nossp_flags) CFLAGS_fdt_rw.o := $(nossp_flags) CFLAGS_fdt_wip.o := $(nossp_flags) -ccflags-y := -fpic -mno-single-pic-base -fno-builtin -I$(obj) +ccflags-y := -fpic $(call cc-option,-mno-single-pic-base,) -fno-builtin -I$(obj) asflags-y := -DZIMAGE # Supply kernel BSS size to the decompressor via a linker symbol. -KBSS_SZ = $(shell $(CROSS_COMPILE)nm $(obj)/../../../../vmlinux | \ - perl -e 'while (<>) { \ - $$bss_start=hex($$1) if /^([[:xdigit:]]+) B __bss_start$$/; \ - $$bss_end=hex($$1) if /^([[:xdigit:]]+) B __bss_stop$$/; \ - }; printf "%d\n", $$bss_end - $$bss_start;') +KBSS_SZ = $(shell echo $$(($$($(CROSS_COMPILE)nm $(obj)/../../../../vmlinux | \ + sed -n -e 's/^\([^ ]*\) [AB] __bss_start$$/-0x\1/p' \ + -e 's/^\([^ ]*\) [AB] __bss_stop$$/+0x\1/p') )) ) LDFLAGS_vmlinux = --defsym _kernel_bss_size=$(KBSS_SZ) # Supply ZRELADDR to the decompressor via a linker symbol. ifneq ($(CONFIG_AUTO_ZRELADDR),y) diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S index 45c8823c3750..517e0e18f0b8 100644 --- a/arch/arm/boot/compressed/head.S +++ b/arch/arm/boot/compressed/head.S @@ -29,19 +29,19 @@ #if defined(CONFIG_DEBUG_ICEDCC) #if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_V6K) || defined(CONFIG_CPU_V7) - .macro loadsp, rb, tmp + .macro loadsp, rb, tmp1, tmp2 .endm .macro writeb, ch, rb mcr p14, 0, \ch, c0, c5, 0 .endm #elif defined(CONFIG_CPU_XSCALE) - .macro loadsp, rb, tmp + .macro loadsp, rb, tmp1, tmp2 .endm .macro writeb, ch, rb mcr p14, 0, \ch, c8, c0, 0 .endm #else - .macro loadsp, rb, tmp + .macro loadsp, rb, tmp1, tmp2 .endm .macro writeb, ch, rb mcr p14, 0, \ch, c1, c0, 0 @@ -57,7 +57,7 @@ .endm #if defined(CONFIG_ARCH_SA1100) - .macro loadsp, rb, tmp + .macro loadsp, rb, tmp1, tmp2 mov \rb, #0x80000000 @ physical base address #ifdef CONFIG_DEBUG_LL_SER3 add \rb, \rb, #0x00050000 @ Ser3 @@ -66,8 +66,8 @@ #endif .endm #else - .macro loadsp, rb, tmp - addruart \rb, \tmp + .macro loadsp, rb, tmp1, tmp2 + addruart \rb, \tmp1, \tmp2 .endm #endif #endif @@ -561,8 +561,6 @@ not_relocated: mov r0, #0 bl decompress_kernel bl cache_clean_flush bl cache_off - mov r1, r7 @ restore architecture number - mov r2, r8 @ restore atags pointer #ifdef CONFIG_ARM_VIRT_EXT mrs r0, spsr @ Get saved CPU boot mode @@ -1297,7 +1295,7 @@ phex: adr r3, phexbuf b 1b @ puts corrupts {r0, r1, r2, r3} -puts: loadsp r3, r1 +puts: loadsp r3, r2, r1 1: ldrb r2, [r0], #1 teq r2, #0 moveq pc, lr @@ -1314,8 +1312,8 @@ puts: loadsp r3, r1 @ putc corrupts {r0, r1, r2, r3} putc: mov r2, r0 + loadsp r3, r1, r0 mov r0, #0 - loadsp r3, r1 b 2b @ memdump corrupts {r0, r1, r2, r3, r10, r11, r12, lr} @@ -1365,6 +1363,8 @@ __hyp_reentry_vectors: __enter_kernel: mov r0, #0 @ must be 0 + mov r1, r7 @ restore architecture number + mov r2, r8 @ restore atags pointer ARM( mov pc, r4 ) @ call kernel M_CLASS( add r4, r4, #1 ) @ enter in Thumb mode for M class THUMB( bx r4 ) @ entry point is always ARM for A/R classes diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 7e2424957809..37a3de760d40 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -75,6 +75,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \ bcm2835-rpi-a-plus.dtb \ bcm2836-rpi-2-b.dtb \ bcm2837-rpi-3-b.dtb \ + bcm2837-rpi-3-b-plus.dtb \ bcm2835-rpi-zero.dtb \ bcm2835-rpi-zero-w.dtb dtb-$(CONFIG_ARCH_BCM_5301X) += \ @@ -102,8 +103,10 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm47094-dlink-dir-885l.dtb \ bcm47094-linksys-panamera.dtb \ bcm47094-luxul-abr-4500.dtb \ + bcm47094-luxul-xap-1610.dtb \ bcm47094-luxul-xbr-4500.dtb \ bcm47094-luxul-xwr-3100.dtb \ + bcm47094-luxul-xwr-3150-v1.dtb \ bcm47094-netgear-r8500.dtb \ bcm94708.dtb \ bcm94709.dtb \ @@ -140,6 +143,7 @@ dtb-$(CONFIG_ARCH_BCM_NSP) += \ dtb-$(CONFIG_ARCH_BERLIN) += \ berlin2-sony-nsz-gs7.dtb \ berlin2cd-google-chromecast.dtb \ + berlin2cd-valve-steamlink.dtb \ berlin2q-marvell-dmp.dtb dtb-$(CONFIG_ARCH_BRCMSTB) += \ bcm7445-bcm97445svmb.dtb @@ -190,8 +194,6 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \ exynos5422-odroidxu3.dtb \ exynos5422-odroidxu3-lite.dtb \ exynos5422-odroidxu4.dtb \ - exynos5440-sd5v1.dtb \ - exynos5440-ssdk5440.dtb \ exynos5800-peach-pi.dtb dtb-$(CONFIG_ARCH_GEMINI) += \ gemini-dlink-dir-685.dtb \ @@ -312,14 +314,14 @@ dtb-$(CONFIG_ARCH_NPCM7XX) += \ dtb-$(CONFIG_MACH_MESON6) += \ meson6-atv1200.dtb dtb-$(CONFIG_MACH_MESON8) += \ - meson8-minix-neo-x8.dtb + meson8-minix-neo-x8.dtb \ + meson8b-mxq.dtb \ + meson8b-odroidc1.dtb \ + meson8m2-mxiii-plus.dtb dtb-$(CONFIG_ARCH_MMP) += \ pxa168-aspenite.dtb \ pxa910-dkb.dtb \ mmp2-brownstone.dtb -dtb-$(CONFIG_MACH_MESON8B) += \ - meson8b-mxq.dtb \ - meson8b-odroidc1.dtb dtb-$(CONFIG_ARCH_MPS2) += \ mps2-an385.dtb \ mps2-an399.dtb @@ -399,6 +401,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-hummingboard2-som-v15.dtb \ imx6dl-icore.dtb \ imx6dl-icore-rqs.dtb \ + imx6dl-mamoj.dtb \ imx6dl-nit6xlite.dtb \ imx6dl-nitrogen6x.dtb \ imx6dl-phytec-mira-rdk-nand.dtb \ @@ -439,6 +442,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-cubox-i-emmc-som-v15.dtb \ imx6q-cubox-i-som-v15.dtb \ imx6q-dfi-fs700-m60.dtb \ + imx6q-dhcom-pdk2.dtb \ imx6q-display5-tianma-tm070-1280x768.dtb \ imx6q-dmo-edmqmx6.dtb \ imx6q-dms-ba16.dtb \ @@ -463,9 +467,11 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-hummingboard2-emmc-som-v15.dtb \ imx6q-hummingboard2-som-v15.dtb \ imx6q-icore.dtb \ + imx6q-icore-mipi.dtb \ imx6q-icore-ofcap10.dtb \ imx6q-icore-ofcap12.dtb \ imx6q-icore-rqs.dtb \ + imx6q-kp-tpc.dtb \ imx6q-marsboard.dtb \ imx6q-mccmon6.dtb \ imx6q-nitrogen6x.dtb \ @@ -688,6 +694,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-pdu001.dtb \ am335x-pepper.dtb \ am335x-phycore-rdk.dtb \ + am335x-pocketbeagle.dtb \ am335x-shc.dtb \ am335x-sbc-t335.dtb \ am335x-sl50.dtb \ @@ -760,12 +767,17 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ qcom-ipq4019-ap.dk01.1-c1.dtb \ + qcom-ipq4019-ap.dk04.1-c1.dtb \ + qcom-ipq4019-ap.dk04.1-c3.dtb \ + qcom-ipq4019-ap.dk07.1-c1.dtb \ + qcom-ipq4019-ap.dk07.1-c2.dtb \ qcom-ipq8064-ap148.dtb \ qcom-msm8660-surf.dtb \ qcom-msm8960-cdp.dtb \ qcom-msm8974-fairphone-fp2.dtb \ qcom-msm8974-lge-nexus5-hammerhead.dtb \ qcom-msm8974-samsung-klte.dtb \ + qcom-msm8974-sony-xperia-amami.dtb \ qcom-msm8974-sony-xperia-castor.dtb \ qcom-msm8974-sony-xperia-honami.dtb \ qcom-mdm9615-wp8548-mangoh-green.dtb @@ -795,6 +807,7 @@ dtb-$(CONFIG_ARCH_RENESAS) += \ r8a7745-iwg22d-sodimm.dtb \ r8a7745-iwg22d-sodimm-dbhd-ca.dtb \ r8a7745-sk-rzg1e.dtb \ + r8a77470-iwg23s-sbc.dtb \ r8a7778-bockw.dtb \ r8a7779-marzen.dtb \ r8a7790-lager.dtb \ @@ -959,6 +972,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \ sun7i-a20-m3.dtb \ sun7i-a20-mk808c.dtb \ sun7i-a20-olimex-som-evb.dtb \ + sun7i-a20-olimex-som-evb-emmc.dtb \ sun7i-a20-olimex-som204-evb.dtb \ sun7i-a20-olimex-som204-evb-emmc.dtb \ sun7i-a20-olinuxino-lime.dtb \ @@ -992,8 +1006,9 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-a83t-bananapi-m3.dtb \ sun8i-a83t-cubietruck-plus.dtb \ sun8i-a83t-tbs-a711.dtb \ - sun8i-h2-plus-orangepi-r1.dtb \ sun8i-h2-plus-bananapi-m2-zero.dtb \ + sun8i-h2-plus-libretech-all-h3-cc.dtb \ + sun8i-h2-plus-orangepi-r1.dtb \ sun8i-h2-plus-orangepi-zero.dtb \ sun8i-h3-bananapi-m2-plus.dtb \ sun8i-h3-beelink-x2.dtb \ @@ -1010,6 +1025,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-h3-orangepi-plus.dtb \ sun8i-h3-orangepi-plus2e.dtb \ sun8i-r16-bananapi-m2m.dtb \ + sun8i-r16-nintendo-nes-classic.dtb \ + sun8i-r16-nintendo-super-nes-classic.dtb \ sun8i-r16-parrot.dtb \ sun8i-r40-bananapi-m2-ultra.dtb \ sun8i-v3s-licheepi-zero.dtb \ @@ -1054,9 +1071,7 @@ dtb-$(CONFIG_ARCH_U8500) += \ ste-hrefprev60-stuib.dtb \ ste-hrefprev60-tvk.dtb \ ste-hrefv60plus-stuib.dtb \ - ste-hrefv60plus-tvk.dtb \ - ste-ccu8540.dtb \ - ste-ccu9540.dtb + ste-hrefv60plus-tvk.dtb dtb-$(CONFIG_ARCH_UNIPHIER) += \ uniphier-ld4-ref.dtb \ uniphier-ld6b-ref.dtb \ @@ -1150,6 +1165,9 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \ mt6580-evbp1.dtb \ mt6589-aquaris5.dtb \ mt6592-evb.dtb \ + mt7623a-rfb-emmc.dtb \ + mt7623a-rfb-nand.dtb \ + mt7623n-rfb-emmc.dtb \ mt7623n-rfb-nand.dtb \ mt7623n-bananapi-bpi-r2.dtb \ mt8127-moose.dtb \ @@ -1158,8 +1176,11 @@ dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-ast2500-evb.dtb \ aspeed-bmc-arm-centriq2400-rep.dtb \ + aspeed-bmc-intel-s2600wf.dtb \ + aspeed-bmc-opp-lanyang.dtb \ aspeed-bmc-opp-palmetto.dtb \ aspeed-bmc-opp-romulus.dtb \ aspeed-bmc-opp-witherspoon.dtb \ aspeed-bmc-opp-zaius.dtb \ + aspeed-bmc-portwell-neptune.dtb \ aspeed-bmc-quanta-q71l.dtb diff --git a/arch/arm/boot/dts/am335x-baltos-ir3220.dts b/arch/arm/boot/dts/am335x-baltos-ir3220.dts index 46df1b22022c..1b215c425c57 100644 --- a/arch/arm/boot/dts/am335x-baltos-ir3220.dts +++ b/arch/arm/boot/dts/am335x-baltos-ir3220.dts @@ -85,7 +85,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-parent = <&gpio0>; - interrupts = <20 GPIO_ACTIVE_LOW>; + interrupts = <20 IRQ_TYPE_EDGE_RISING>; pinctrl-names = "default"; pinctrl-0 = <&tca6416_pins>; }; diff --git a/arch/arm/boot/dts/am335x-baltos-ir5221.dts b/arch/arm/boot/dts/am335x-baltos-ir5221.dts index 5d56355ba040..832ead864dc5 100644 --- a/arch/arm/boot/dts/am335x-baltos-ir5221.dts +++ b/arch/arm/boot/dts/am335x-baltos-ir5221.dts @@ -94,7 +94,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-parent = <&gpio0>; - interrupts = <20 GPIO_ACTIVE_LOW>; + interrupts = <20 IRQ_TYPE_EDGE_RISING>; pinctrl-names = "default"; pinctrl-0 = <&tca6416_pins>; }; diff --git a/arch/arm/boot/dts/am335x-baltos.dtsi b/arch/arm/boot/dts/am335x-baltos.dtsi index ec6052c521ef..ed7a5a3daa42 100644 --- a/arch/arm/boot/dts/am335x-baltos.dtsi +++ b/arch/arm/boot/dts/am335x-baltos.dtsi @@ -249,7 +249,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-parent = <&gpio1>; - interrupts = <28 GPIO_ACTIVE_LOW>; + interrupts = <28 IRQ_TYPE_EDGE_RISING>; pinctrl-names = "default"; pinctrl-0 = <&tps65910_pins>; }; diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi index e67b4d65c8d0..f9e8667f5886 100644 --- a/arch/arm/boot/dts/am335x-bone-common.dtsi +++ b/arch/arm/boot/dts/am335x-bone-common.dtsi @@ -161,7 +161,14 @@ mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* GPIO0_6 */ + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spio0_cs1.gpio0_6 */ + AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + AM33XX_IOPAD(0x9a0, PIN_INPUT | MUX_MODE4) /* mcasp0_aclkr.mmc0_sdwp */ >; }; diff --git a/arch/arm/boot/dts/am335x-boneblue.dts b/arch/arm/boot/dts/am335x-boneblue.dts index 58baee158e64..7bcd72691f06 100644 --- a/arch/arm/boot/dts/am335x-boneblue.dts +++ b/arch/arm/boot/dts/am335x-boneblue.dts @@ -364,7 +364,7 @@ compatible = "invensense,mpu9250"; reg = <0x68>; interrupt-parent = <&gpio3>; - interrupts = <21 GPIO_ACTIVE_LOW>; + interrupts = <21 IRQ_TYPE_EDGE_RISING>; i2c-gate { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts index fee6b3ee1741..1356fd6f8da3 100644 --- a/arch/arm/boot/dts/am335x-evm.dts +++ b/arch/arm/boot/dts/am335x-evm.dts @@ -303,7 +303,14 @@ mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + AM33XX_IOPAD(0x9a0, PIN_INPUT | MUX_MODE4) /* mcasp0_aclkr.mmc0_sdwp */ >; }; diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index fa608cd5dc14..0c096a795e37 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -137,7 +137,7 @@ }; }; - backlight { + lcd_bl: backlight { compatible = "pwm-backlight"; pwms = <&ecap2 0 50000 PWM_POLARITY_INVERTED>; brightness-levels = <0 58 61 66 75 90 125 170 255>; @@ -172,6 +172,7 @@ pinctrl-names = "default", "sleep"; pinctrl-0 = <&lcd_pins_default>; pinctrl-1 = <&lcd_pins_sleep>; + backlight = <&lcd_bl>; status = "okay"; panel-info { ac-bias = <255>; @@ -399,7 +400,14 @@ mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + AM33XX_IOPAD(0x9a0, PIN_INPUT | MUX_MODE4) /* mcasp0_aclkr.mmc0_sdwp */ >; }; diff --git a/arch/arm/boot/dts/am335x-osd335x-common.dtsi b/arch/arm/boot/dts/am335x-osd335x-common.dtsi new file mode 100644 index 000000000000..f8ff473f94f0 --- /dev/null +++ b/arch/arm/boot/dts/am335x-osd335x-common.dtsi @@ -0,0 +1,124 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * Author: Robert Nelson <robertcnelson@gmail.com> + */ + +/ { + cpus { + cpu@0 { + cpu0-supply = <&dcdc2_reg>; + }; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x20000000>; /* 512 MB */ + }; +}; + +&cpu0_opp_table { + /* + * Octavo Systems: + * The EFUSE_SMA register is not programmed for any of the AM335x wafers + * we get and we are not programming them during our production test. + * Therefore, from a DEVICE_ID revision point of view, the silicon looks + * like it is Revision 2.1. However, from an EFUSE_SMA point of view for + * the HW OPP table, the silicon looks like it is Revision 1.0 (ie the + * EFUSE_SMA register reads as all zeros). + */ + oppnitro-1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +&am33xx_pinmux { + i2c0_pins: pinmux-i2c0-pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* (C17) I2C0_SDA.I2C0_SDA */ + AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* (C16) I2C0_SCL.I2C0_SCL */ + >; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + tps: tps@24 { + reg = <0x24>; + }; +}; + +/include/ "tps65217.dtsi" + +&tps { + interrupts = <7>; /* NMI */ + interrupt-parent = <&intc>; + + ti,pmic-shutdown-controller; + + pwrbutton { + interrupts = <2>; + status = "okay"; + }; + + regulators { + dcdc1_reg: regulator@0 { + regulator-name = "vdds_dpr"; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1351500>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + regulator-name = "vio,vrtc,vdds"; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + regulator-name = "vdd_3v3aux"; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + regulator-name = "vdd_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + regulator-name = "vdd_3v3a"; + regulator-always-on; + }; + }; +}; + +&aes { + status = "okay"; +}; + +&sham { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/am335x-pocketbeagle.dts b/arch/arm/boot/dts/am335x-pocketbeagle.dts new file mode 100644 index 000000000000..62fe5cab9fae --- /dev/null +++ b/arch/arm/boot/dts/am335x-pocketbeagle.dts @@ -0,0 +1,237 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * Author: Robert Nelson <robertcnelson@gmail.com> + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-osd335x-common.dtsi" + +/ { + model = "TI AM335x PocketBeagle"; + compatible = "ti,am335x-pocketbeagle", "ti,am335x-bone", "ti,am33xx"; + + chosen { + stdout-path = &uart0; + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&usr_leds_pins>; + + compatible = "gpio-leds"; + + usr0 { + label = "beaglebone:green:usr0"; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + usr1 { + label = "beaglebone:green:usr1"; + gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + usr2 { + label = "beaglebone:green:usr2"; + gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "cpu0"; + default-state = "off"; + }; + + usr3 { + label = "beaglebone:green:usr3"; + gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + vmmcsd_fixed: fixedregulator0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&am33xx_pinmux { + i2c2_pins: pinmux-i2c2-pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE3) /* (D17) uart1_rtsn.I2C2_SCL */ + AM33XX_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE3) /* (D18) uart1_ctsn.I2C2_SDA */ + >; + }; + + ehrpwm0_pins: pinmux-ehrpwm0-pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* (A13) mcasp0_aclkx.ehrpwm0A */ + >; + }; + + ehrpwm1_pins: pinmux-ehrpwm1-pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x848, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* (U14) gpmc_a2.ehrpwm1A */ + >; + }; + + mmc0_pins: pinmux-mmc0-pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* (C15) spi0_cs1.gpio0[6] */ + AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* (G16) mmc0_dat0.mmc0_dat0 */ + AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* (G15) mmc0_dat1.mmc0_dat1 */ + AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* (F18) mmc0_dat2.mmc0_dat2 */ + AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* (F17) mmc0_dat3.mmc0_dat3 */ + AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* (G18) mmc0_cmd.mmc0_cmd */ + AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* (G17) mmc0_clk.mmc0_clk */ + AM33XX_IOPAD(0x9a0, PIN_INPUT | MUX_MODE4) /* (B12) mcasp0_aclkr.mmc0_sdwp */ + >; + }; + + spi0_pins: pinmux-spi0-pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x950, PIN_INPUT_PULLUP | MUX_MODE0) /* (A17) spi0_sclk.spi0_sclk */ + AM33XX_IOPAD(0x954, PIN_INPUT_PULLUP | MUX_MODE0) /* (B17) spi0_d0.spi0_d0 */ + AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0) /* (B16) spi0_d1.spi0_d1 */ + AM33XX_IOPAD(0x95c, PIN_INPUT_PULLUP | MUX_MODE0) /* (A16) spi0_cs0.spi0_cs0 */ + >; + }; + + spi1_pins: pinmux-spi1-pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x964, PIN_INPUT_PULLUP | MUX_MODE4) /* (C18) eCAP0_in_PWM0_out.spi1_sclk */ + AM33XX_IOPAD(0x968, PIN_INPUT_PULLUP | MUX_MODE4) /* (E18) uart0_ctsn.spi1_d0 */ + AM33XX_IOPAD(0x96c, PIN_INPUT_PULLUP | MUX_MODE4) /* (E17) uart0_rtsn.spi1_d1 */ + AM33XX_IOPAD(0x9b0, PIN_INPUT_PULLUP | MUX_MODE4) /* (A15) xdma_event_intr0.spi1_cs1 */ + >; + }; + + usr_leds_pins: pinmux-usr-leds-pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE7) /* (V15) gpmc_a5.gpio1[21] - USR_LED_0 */ + AM33XX_IOPAD(0x858, PIN_OUTPUT | MUX_MODE7) /* (U15) gpmc_a6.gpio1[22] - USR_LED_1 */ + AM33XX_IOPAD(0x85c, PIN_OUTPUT | MUX_MODE7) /* (T15) gpmc_a7.gpio1[23] - USR_LED_2 */ + AM33XX_IOPAD(0x860, PIN_OUTPUT | MUX_MODE7) /* (V16) gpmc_a8.gpio1[24] - USR_LED_3 */ + >; + }; + + uart0_pins: pinmux-uart0-pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* (E15) uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* (E16) uart0_txd.uart0_txd */ + >; + }; + + uart4_pins: pinmux-uart4-pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE6) /* (T17) gpmc_wait0.uart4_rxd */ + AM33XX_IOPAD(0x874, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* (U17) gpmc_wpn.uart4_txd */ + >; + }; +}; + +&epwmss0 { + status = "okay"; +}; + +&ehrpwm0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&ehrpwm0_pins>; +}; + +&epwmss1 { + status = "okay"; +}; + +&ehrpwm1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&ehrpwm1_pins>; +}; + +&i2c0 { + eeprom: eeprom@50 { + compatible = "atmel,24c256"; + reg = <0x50>; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + status = "okay"; + clock-frequency = <400000>; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; +}; + +&rtc { + system-power-controller; +}; + +&tscadc { + status = "okay"; + adc { + ti,adc-channels = <0 1 2 3 4 5 6 7>; + ti,chan-step-avg = <16 16 16 16 16 16 16 16>; + ti,chan-step-opendelay = <0x98 0x98 0x98 0x98 0x98 0x98 0x98 0x98>; + ti,chan-step-sampledelay = <0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0>; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins>; + + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; + dr_mode = "otg"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb1 { + status = "okay"; + dr_mode = "host"; +}; + +&cppi41dma { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/am3517-evm.dts b/arch/arm/boot/dts/am3517-evm.dts index 0e4a125f78e3..98aadb0f81c5 100644 --- a/arch/arm/boot/dts/am3517-evm.dts +++ b/arch/arm/boot/dts/am3517-evm.dts @@ -8,11 +8,17 @@ /dts-v1/; #include "am3517.dtsi" +#include "am3517-som.dtsi" +#include <dt-bindings/input/input.h> / { model = "TI AM3517 EVM (AM3517/05 TMDSEVM3517)"; compatible = "ti,am3517-evm", "ti,am3517", "ti,omap3"; + aliases { + display0 = &lcd0; + }; + memory@80000000 { device_type = "memory"; reg = <0x80000000 0x10000000>; /* 256 MB */ @@ -24,6 +30,144 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; + + gpio-keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + user_pb { + label = "User Push Button"; + linux,code = <BTN_0>; + gpios = <&tca6416 5 GPIO_ACTIVE_LOW>; + }; + + user_sw_1 { + label = "User Switch 1"; + linux,code = <BTN_1>; + gpios = <&tca6416 8 GPIO_ACTIVE_LOW>; + }; + + user_sw_2 { + label = "User Switch 2"; + linux,code = <BTN_2>; + gpios = <&tca6416 9 GPIO_ACTIVE_LOW>; + }; + + user_sw_3 { + label = "User Switch 3"; + linux,code = <BTN_3>; + gpios = <&tca6416 10 GPIO_ACTIVE_LOW>; + }; + + user_sw_4 { + label = "User Switch 4"; + linux,code = <BTN_4>; + gpios = <&tca6416 11 GPIO_ACTIVE_LOW>; + }; + + user_sw_5 { + label = "User Switch 5"; + linux,code = <BTN_5>; + gpios = <&tca6416 12 GPIO_ACTIVE_LOW>; + }; + + user_sw_6 { + label = "User Switch 6"; + linux,code = <BTN_6>; + gpios = <&tca6416 13 GPIO_ACTIVE_LOW>; + }; + + user_sw_7 { + label = "User Switch 7"; + linux,code = <BTN_7>; + gpios = <&tca6416 14 GPIO_ACTIVE_LOW>; + }; + + user_sw_8 { + label = "User Switch 8"; + linux,code = <BTN_8>; + gpios = <&tca6416 15 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&leds_pins>; + + user_led_1 { + label = "am3517evm:green:user_led_1"; + gpios = <&tca6416 7 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + user_led_2 { + label = "am3517evm:green:user_led_2"; + gpios = <&tca6416 6 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + user_led_3 { + label = "am3517evm:green:user_led_3"; + gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; /* SD/MMC card activity */ + }; + + user_led_4 { + label = "am3517evm:green:user_led_4"; + gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + lcd0: display@0 { + compatible = "panel-dpi"; + label = "15"; + status = "okay"; + pinctrl-names = "default"; + enable-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>; /* gpio176, lcd INI */ + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <2>; + hsync-len = <42>; + vback-porch = <3>; + vfront-porch = <4>; + vsync-len = <11>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + + bl: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&backlight_pins>; + pwms = <&pwm11 0 5000000 0>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <7>; + enable-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* gpio_182 */ + }; + + pwm11: dmtimer-pwm@11 { + compatible = "ti,omap-dmtimer-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pins>; + ti,timers = <&timer11>; + #pwm-cells = <3>; + }; }; &davinci_emac { @@ -34,12 +178,32 @@ status = "okay"; }; -&i2c1 { - clock-frequency = <400000>; +&dss { + status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins>; + + vdds_dsi-supply = <&vdd_io_reg>; + vdda_video-supply = <&vdd_io_reg>; + + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <16>; + }; + }; }; &i2c2 { clock-frequency = <400000>; + /* User DIP swithes [1:8] / User LEDS [1:2] */ + tca6416: gpio@21 { + compatible = "ti,tca6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + }; }; &i2c3 { @@ -47,8 +211,13 @@ }; &mmc1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; vmmc-supply = <&vmmc_fixed>; bus-width = <4>; + wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>; /* gpio_126 */ + cd-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio_127 */ }; &mmc2 { @@ -59,3 +228,63 @@ status = "disabled"; }; +&omap3_pmx_core { + + leds_pins: pinmux_leds_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu0.gpio_11 */ + OMAP3_WKUP_IOPAD(0x2a26, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu1.gpio_31 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE4) /* sdmmc1_dat4.gpio_126 */ + OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE4) /* sdmmc1_dat5.gpio_127 */ + >; + }; + + pwm_pins: pinmux_pwm_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21dc, PIN_OUTPUT | MUX_MODE1) /* mcspi2_cs0.gpt11_pwm */ + >; + }; + + backlight_pins: pinmux_backlight_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21de, PIN_OUTPUT | MUX_MODE4) /* mcspi2_cs1.gpio_182 */ + >; + }; + + dss_dpi_pins: pinmux_dss_dpi_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d2, PIN_OUTPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */ + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ + >; + }; +}; diff --git a/arch/arm/boot/dts/am3517-som.dtsi b/arch/arm/boot/dts/am3517-som.dtsi new file mode 100644 index 000000000000..a6d5ff73c163 --- /dev/null +++ b/arch/arm/boot/dts/am3517-som.dtsi @@ -0,0 +1,142 @@ +/* + * Copyright (C) 2016 Derald D. Woods <woods.technical@gmail.com> + * + * Based on am3517-evm.dts + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + cpus { + cpu@0 { + cpu0-supply = <&vdd_core_reg>; + }; + }; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */ + + nand@0,0 { + compatible = "ti,omap2-nand"; + linux,mtd-name = "micron,mt29f4g16abchch"; + reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ + nand-bus-width = <16>; + ti,nand-ecc-opt = "bch8"; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-off-ns = <40>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + gpmc,device-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + + s35390a: s35390a@30 { + compatible = "sii,s35390a"; + reg = <0x30>; + + pinctrl-names = "default"; + pinctrl-0 = <&rtc_pins>; + interrupts-extended = <&gpio2 23 IRQ_TYPE_EDGE_FALLING>; /* gpio_55 */ + }; + + tps: tps65023@48 { + compatible = "ti,tps65023"; + reg = <0x48>; + + regulators { + vdd_core_reg: VDCDC1 { + regulator-name = "vdd_core"; + compatible = "regulator-fixed"; + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vdd_io_reg: VDCDC2 { + regulator-name = "vdd_io"; + compatible = "regulator-fixed"; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vdd_1v8_reg: VDCDC3 { + regulator-name = "vdd_1v8"; + compatible = "regulator-fixed"; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vdd_usb18_reg: LDO1 { + regulator-name = "vdd_usb18"; + compatible = "regulator-fixed"; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vdd_usb33_reg: LDO2 { + regulator-name = "vdd_usb33"; + compatible = "regulator-fixed"; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + + touchscreen: tsc2004@4b { + compatible = "ti,tsc2004"; + reg = <0x4b>; + + vio-supply = <&vdd_io_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&tsc2004_pins>; + interrupts-extended = <&gpio3 1 IRQ_TYPE_EDGE_RISING>; /* gpio_65 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <480>; + touchscreen-size-y = <272>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +}; + +&omap3_pmx_core { + + rtc_pins: pinmux_rtc_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20b6, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_ncs4.gpio_55 */ + >; + }; + + tsc2004_pins: pinmux_tsc2004_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT | MUX_MODE4) /* gpmc_wait3.gpio_65 */ + >; + }; +}; diff --git a/arch/arm/boot/dts/am437x-cm-t43.dts b/arch/arm/boot/dts/am437x-cm-t43.dts index 3b9a94c274a7..bff5abe69bdb 100644 --- a/arch/arm/boot/dts/am437x-cm-t43.dts +++ b/arch/arm/boot/dts/am437x-cm-t43.dts @@ -203,7 +203,7 @@ tps65218: tps65218@24 { compatible = "ti,tps65218"; reg = <0x24>; - interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* NMIn */ + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* NMIn */ interrupt-parent = <&gic>; interrupt-controller; #interrupt-cells = <2>; diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts index 8fe95cd7232a..60414b1ca404 100644 --- a/arch/arm/boot/dts/am437x-gp-evm.dts +++ b/arch/arm/boot/dts/am437x-gp-evm.dts @@ -543,7 +543,7 @@ tps65218: tps65218@24 { reg = <0x24>; compatible = "ti,tps65218"; - interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* NMIn */ + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* NMIn */ interrupt-controller; #interrupt-cells = <2>; diff --git a/arch/arm/boot/dts/am437x-sk-evm.dts b/arch/arm/boot/dts/am437x-sk-evm.dts index 4118802b7fea..440351ad0b80 100644 --- a/arch/arm/boot/dts/am437x-sk-evm.dts +++ b/arch/arm/boot/dts/am437x-sk-evm.dts @@ -15,6 +15,7 @@ #include <dt-bindings/pwm/pwm.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> / { model = "TI AM437x SK EVM"; @@ -158,6 +159,22 @@ }; }; }; + + vmmcwl_fixed: fixedregulator-mmcwl { + /* + * WL_EN is not SDIO standard compliant. It is an out of band + * signal and hard to be dealt with in a standard way by the + * SDIO core driver. + * So modelling the WL_EN line as a regulator was a natural + * choice as the MMC core already deals with MMC supplies. + */ + compatible = "regulator-fixed"; + regulator-name = "vmmcwl_fixed"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; }; &am43xx_pinmux { @@ -418,6 +435,62 @@ AM4372_IOPAD(0xac4, PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */ >; }; + + mmc3_pins_default: pinmux_mmc3_pins_default { + pinctrl-single,pins = < + AM4372_IOPAD(0x9f0, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD21) cam1_data2.mmc2_clk */ + AM4372_IOPAD(0x9f4, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE22) cam1_data3.mmc2_cmd */ + AM4372_IOPAD(0x9f8, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD22) cam1_data4.mmc2_dat0 */ + AM4372_IOPAD(0x9fc, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE23) cam1_data5.mmc2_dat1 */ + AM4372_IOPAD(0xa00, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD23) cam1_data6.mmc2_dat2 */ + AM4372_IOPAD(0xa04, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE24) cam1_data7.mmc2_dat3 */ + >; + }; + + mmc3_pins_sleep: pinmux_mmc3_pins_sleep { + pinctrl-single,pins = < + AM4372_IOPAD(0x9f0, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD21) cam1_data2.mmc2_clk */ + AM4372_IOPAD(0x9f4, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE22) cam1_data3.mmc2_cmd */ + AM4372_IOPAD(0x9f8, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD22) cam1_data4.mmc2_dat0 */ + AM4372_IOPAD(0x9fc, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE23) cam1_data5.mmc2_dat1 */ + AM4372_IOPAD(0xa00, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD23) cam1_data6.mmc2_dat2 */ + AM4372_IOPAD(0xa04, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE24) cam1_data7.mmc2_dat3 */ + >; + }; + + wlan_pins_default: pinmux_wlan_pins_default { + pinctrl-single,pins = < + AM4372_IOPAD(0x9d0, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* cam1_data8.gpio4_8 WL_EN */ + AM4372_IOPAD(0x9e4, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* cam1_wen.gpio4_13 WL_IRQ */ + >; + }; + + wlan_pins_sleep: pinmux_wlan_pins_sleep { + pinctrl-single,pins = < + AM4372_IOPAD(0x9d0, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* cam1_data8.gpio4_8 WL_EN */ + AM4372_IOPAD(0x9e4, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* cam1_wen.gpio4_13 WL_IRQ */ + >; + }; + + uart1_bt_pins_default: pinmux_uart1_bt_pins_default { + pinctrl-single,pins = < + AM4372_IOPAD(0x980, PIN_INPUT | MUX_MODE0) /* uart1_rxd.uart1_rxd */ + AM4372_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */ + AM4372_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */ + AM4372_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */ + AM4372_IOPAD(0x9cc, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* cam1_data9.gpio4_7 BT_EN */ + >; + }; + + uart1_bt_pins_sleep: pinmux_uart1_bt_pins_sleep { + pinctrl-single,pins = < + AM4372_IOPAD(0x980, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_rxd.uart1_rxd */ + AM4372_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_txd.uart1_txd */ + AM4372_IOPAD(0x978, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_ctsn.uart1_ctsn */ + AM4372_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_rtsn.uart1_rtsn */ + AM4372_IOPAD(0x9cc, PIN_OUTPUT_PULLUP | MUX_MODE7) /* cam1_data9.gpio4_7 BT_EN */ + >; + }; }; &i2c0 { @@ -581,6 +654,10 @@ status = "okay"; }; +&gpio4 { + status = "okay"; +}; + &gpio5 { status = "okay"; }; @@ -595,6 +672,44 @@ cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; }; +&uart1 { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&uart1_bt_pins_default>; + pinctrl-1 = <&uart1_bt_pins_sleep>; +}; + +&mmc3 { + status = "okay"; + /* + * these are on the crossbar and are outlined in the + * xbar-event-map element + */ + dmas = <&edma_xbar 30 0 1>, + <&edma_xbar 31 0 2>; + dma-names = "tx", "rx"; + vmmc-supply = <&vmmcwl_fixed>; + bus-width = <4>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mmc3_pins_default>; + pinctrl-1 = <&mmc3_pins_sleep>; + cap-power-off-card; + keep-power-in-suspend; + ti,non-removable; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1835"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&wlan_pins_default>; + pinctrl-1 = <&wlan_pins_sleep>; + reg = <2>; + interrupt-parent = <&gpio4>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + &usb2_phy1 { status = "okay"; }; diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index a66941885c11..6502d3397653 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -595,7 +595,7 @@ tps65218: tps65218@24 { reg = <0x24>; compatible = "ti,tps65218"; - interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* NMIn */ + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* NMIn */ interrupt-controller; #interrupt-cells = <2>; diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts index a2555140babc..5bb9d68d6e90 100644 --- a/arch/arm/boot/dts/am571x-idk.dts +++ b/arch/arm/boot/dts/am571x-idk.dts @@ -10,6 +10,7 @@ #include "dra72x.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> +#include "dra7-mmc-iodelay.dtsi" #include "dra72x-mmc-iodelay.dtsi" #include "am57xx-idk-common.dtsi" @@ -102,7 +103,7 @@ &mmc1 { pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; - pinctrl-0 = <&mmc1_pins_default>; + pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; pinctrl-1 = <&mmc1_pins_hs>; pinctrl-2 = <&mmc1_pins_sdr12>; pinctrl-3 = <&mmc1_pins_sdr25>; @@ -112,7 +113,7 @@ }; &mmc2 { - pinctrl-names = "default", "hs", "ddr_1_8v"; + pinctrl-names = "default", "hs", "ddr_3_3v"; pinctrl-0 = <&mmc2_pins_default>; pinctrl-1 = <&mmc2_pins_hs>; pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>; diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts index 3a02ed720957..3ef9111d0e8b 100644 --- a/arch/arm/boot/dts/am572x-idk.dts +++ b/arch/arm/boot/dts/am572x-idk.dts @@ -9,6 +9,7 @@ /dts-v1/; #include "dra74x.dtsi" +#include "dra7-mmc-iodelay.dtsi" #include "dra74x-mmc-iodelay.dtsi" #include "am572x-idk-common.dtsi" @@ -20,7 +21,7 @@ &mmc1 { pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; - pinctrl-0 = <&mmc1_pins_default>; + pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; pinctrl-1 = <&mmc1_pins_hs>; pinctrl-2 = <&mmc1_pins_sdr12>; pinctrl-3 = <&mmc1_pins_sdr25>; @@ -30,7 +31,7 @@ }; &mmc2 { - pinctrl-names = "default", "hs", "ddr_1_8v"; + pinctrl-names = "default", "hs", "ddr_3_3v"; pinctrl-0 = <&mmc2_pins_default>; pinctrl-1 = <&mmc2_pins_hs>; pinctrl-2 = <&mmc2_pins_ddr_rev20>; diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/am574x-idk.dts index 41e12a382d2f..378dfa780ac1 100644 --- a/arch/arm/boot/dts/am574x-idk.dts +++ b/arch/arm/boot/dts/am574x-idk.dts @@ -7,6 +7,8 @@ /dts-v1/; #include "dra76x.dtsi" +#include "dra7-mmc-iodelay.dtsi" +#include "dra76x-mmc-iodelay.dtsi" #include "am572x-idk-common.dtsi" / { @@ -20,3 +22,21 @@ spi-max-frequency = <96000000>; }; }; + +&mmc1 { + pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; + pinctrl-1 = <&mmc1_pins_hs>; + pinctrl-2 = <&mmc1_pins_default>; + pinctrl-3 = <&mmc1_pins_hs>; + pinctrl-4 = <&mmc1_pins_sdr50>; + pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_conf>; + pinctrl-6 = <&mmc1_pins_ddr50 &mmc1_iodelay_sdr104_conf>; +}; + +&mmc2 { + pinctrl-names = "default", "hs", "ddr_3_3v"; + pinctrl-0 = <&mmc2_pins_default>; + pinctrl-1 = <&mmc2_pins_default>; + pinctrl-2 = <&mmc2_pins_default>; +}; diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi index 6204a266212a..ad953113cefb 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi +++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi @@ -444,8 +444,8 @@ vmmc-supply = <&vdd_3v3>; vqmmc-supply = <&vdd_3v3>; bus-width = <8>; - ti,non-removable; - cap-mmc-dual-data-rate; + non-removable; + no-1-8-v; }; &sata { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index d6689106d2a8..70a71c641066 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -25,10 +25,11 @@ pinctrl-1 = <&mmc1_pins_hs>; vmmc-supply = <&ldo1_reg>; + no-1-8-v; }; &mmc2 { - pinctrl-names = "default", "hs", "ddr_1_8v"; + pinctrl-names = "default", "hs", "ddr_3_3v"; pinctrl-0 = <&mmc2_pins_default>; pinctrl-1 = <&mmc2_pins_hs>; pinctrl-2 = <&mmc2_pins_ddr_3_3v_rev11 &mmc2_iodelay_ddr_3_3v_rev11_conf>; diff --git a/arch/arm/boot/dts/am57xx-idk-common.dtsi b/arch/arm/boot/dts/am57xx-idk-common.dtsi index 43cdf523a8a0..ad87f1ae904d 100644 --- a/arch/arm/boot/dts/am57xx-idk-common.dtsi +++ b/arch/arm/boot/dts/am57xx-idk-common.dtsi @@ -115,17 +115,6 @@ DRA7XX_CORE_IOPAD(0x37d4, MUX_MODE15 | PULL_UP) /* dcan1_rx.off */ >; }; - - mmc1_pins_default: mmc1_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mmc1_clk.clk */ - DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ - DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ - DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ - DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ - DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ - >; - }; }; &i2c1 { @@ -423,8 +412,9 @@ vmmc-supply = <&v3_3d>; vqmmc-supply = <&v3_3d>; bus-width = <8>; - ti,non-removable; + non-removable; max-frequency = <96000000>; + no-1-8-v; }; &dcan1 { diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts index afe46097a403..77261a2fb949 100644 --- a/arch/arm/boot/dts/armada-370-db.dts +++ b/arch/arm/boot/dts/armada-370-db.dts @@ -105,33 +105,6 @@ usb@51000 { status = "okay"; }; - - nand@d0000 { - status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "U-Boot"; - reg = <0 0x800000>; - }; - partition@800000 { - label = "Linux"; - reg = <0x800000 0x800000>; - }; - partition@1000000 { - label = "Filesystem"; - reg = <0x1000000 0x3f000000>; - }; - }; - }; }; }; @@ -239,3 +212,33 @@ }; }; +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x800000>; + }; + partition@800000 { + label = "Linux"; + reg = <0x800000 0x800000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-dlink-dns327l.dts b/arch/arm/boot/dts/armada-370-dlink-dns327l.dts index 8e46f63cbaa1..baa459dd51e4 100644 --- a/arch/arm/boot/dts/armada-370-dlink-dns327l.dts +++ b/arch/arm/boot/dts/armada-370-dlink-dns327l.dts @@ -44,61 +44,6 @@ usb@50000 { status = "okay"; }; - - nand@d0000 { - status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partition@0 { - label = "u-boot"; - /* 1.0 MiB */ - reg = <0x0000000 0x100000>; - read-only; - }; - - partition@100000 { - label = "u-boot-env"; - /* 128 KiB */ - reg = <0x100000 0x20000>; - read-only; - }; - - partition@120000 { - label = "uImage"; - /* 7 MiB */ - reg = <0x120000 0x700000>; - }; - - partition@820000 { - label = "ubifs"; - /* ~ 84 MiB */ - reg = <0x820000 0x54e0000>; - }; - - /* Hardcoded into stock bootloader */ - partition@5d00000 { - label = "failsafe-uImage"; - /* 5 MiB */ - reg = <0x5d00000 0x500000>; - }; - - partition@6200000 { - label = "failsafe-fs"; - /* 29 MiB */ - reg = <0x6200000 0x1d00000>; - }; - - partition@7f00000 { - label = "bbt"; - /* 1 MiB for BBT */ - reg = <0x7f00000 0x100000>; - }; - }; }; }; @@ -319,3 +264,68 @@ clock-frequency = <100000>; status = "okay"; }; + +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + /* 1.0 MiB */ + reg = <0x0000000 0x100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + /* 128 KiB */ + reg = <0x100000 0x20000>; + read-only; + }; + + partition@120000 { + label = "uImage"; + /* 7 MiB */ + reg = <0x120000 0x700000>; + }; + + partition@820000 { + label = "ubifs"; + /* ~ 84 MiB */ + reg = <0x820000 0x54e0000>; + }; + + /* Hardcoded into stock bootloader */ + partition@5d00000 { + label = "failsafe-uImage"; + /* 5 MiB */ + reg = <0x5d00000 0x500000>; + }; + + partition@6200000 { + label = "failsafe-fs"; + /* 29 MiB */ + reg = <0x6200000 0x1d00000>; + }; + + partition@7f00000 { + label = "bbt"; + /* 1 MiB for BBT */ + reg = <0x7f00000 0x100000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-mirabox.dts b/arch/arm/boot/dts/armada-370-mirabox.dts index 996f31b00729..7c2f5a79b50d 100644 --- a/arch/arm/boot/dts/armada-370-mirabox.dts +++ b/arch/arm/boot/dts/armada-370-mirabox.dts @@ -108,27 +108,6 @@ reg = <0x25>; }; }; - - nand@d0000 { - status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - - partition@0 { - label = "U-Boot"; - reg = <0 0x400000>; - }; - partition@400000 { - label = "Linux"; - reg = <0x400000 0x400000>; - }; - partition@800000 { - label = "Filesystem"; - reg = <0x800000 0x3f800000>; - }; - }; }; }; }; @@ -173,3 +152,33 @@ }; }; +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x400000>; + }; + partition@400000 { + label = "Linux"; + reg = <0x400000 0x400000>; + }; + partition@800000 { + label = "Filesystem"; + reg = <0x800000 0x3f800000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts index 56634803e16b..b0b640b7de40 100644 --- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts +++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts @@ -81,46 +81,6 @@ pwm_polarity = <0>; }; }; - - nand@d0000 { - status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - - /* Use Hardware BCH ECC */ - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x180000>; /* 1.5MB */ - read-only; - }; - - partition@180000 { - label = "u-boot-env"; - reg = <0x180000 0x20000>; /* 128KB */ - read-only; - }; - - partition@200000 { - label = "uImage"; - reg = <0x0200000 0x600000>; /* 6MB */ - }; - - partition@800000 { - label = "minirootfs"; - reg = <0x0800000 0x400000>; /* 4MB */ - }; - - /* Last MB is for the BBT, i.e. not writable */ - partition@c00000 { - label = "ubifs"; - reg = <0x0c00000 0x7400000>; /* 116MB */ - }; - }; }; }; @@ -264,3 +224,53 @@ marvell,function = "gpio"; }; }; + +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + + /* Use Hardware BCH ECC */ + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x180000>; /* 1.5MB */ + read-only; + }; + + partition@180000 { + label = "u-boot-env"; + reg = <0x180000 0x20000>; /* 128KB */ + read-only; + }; + + partition@200000 { + label = "uImage"; + reg = <0x0200000 0x600000>; /* 6MB */ + }; + + partition@800000 { + label = "minirootfs"; + reg = <0x0800000 0x400000>; /* 4MB */ + }; + + /* Last MB is for the BBT, i.e. not writable */ + partition@c00000 { + label = "ubifs"; + reg = <0x0c00000 0x7400000>; /* 116MB */ + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-netgear-rn104.dts b/arch/arm/boot/dts/armada-370-netgear-rn104.dts index 16d0307f786a..9fd1cb9f4992 100644 --- a/arch/arm/boot/dts/armada-370-netgear-rn104.dts +++ b/arch/arm/boot/dts/armada-370-netgear-rn104.dts @@ -90,46 +90,6 @@ reg = <0x23>; }; }; - - nand@d0000 { - status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - - /* Use Hardware BCH ECC */ - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x180000>; /* 1.5MB */ - read-only; - }; - - partition@180000 { - label = "u-boot-env"; - reg = <0x180000 0x20000>; /* 128KB */ - read-only; - }; - - partition@200000 { - label = "uImage"; - reg = <0x0200000 0x600000>; /* 6MB */ - }; - - partition@800000 { - label = "minirootfs"; - reg = <0x0800000 0x400000>; /* 4MB */ - }; - - /* Last MB is for the BBT, i.e. not writable */ - partition@c00000 { - label = "ubifs"; - reg = <0x0c00000 0x7400000>; /* 116MB */ - }; - }; }; }; @@ -276,3 +236,53 @@ marvell,function = "gpio"; }; }; + +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + + /* Use Hardware BCH ECC */ + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x180000>; /* 1.5MB */ + read-only; + }; + + partition@180000 { + label = "u-boot-env"; + reg = <0x180000 0x20000>; /* 128KB */ + read-only; + }; + + partition@200000 { + label = "uImage"; + reg = <0x0200000 0x600000>; /* 6MB */ + }; + + partition@800000 { + label = "minirootfs"; + reg = <0x0800000 0x400000>; /* 4MB */ + }; + + /* Last MB is for the BBT, i.e. not writable */ + partition@c00000 { + label = "ubifs"; + reg = <0x0c00000 0x7400000>; /* 116MB */ + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/armada-370-rd.dts index cc2f774eb267..2bfb3108b5b2 100644 --- a/arch/arm/boot/dts/armada-370-rd.dts +++ b/arch/arm/boot/dts/armada-370-rd.dts @@ -112,27 +112,6 @@ default-state = "keep"; }; }; - - nand@d0000 { - status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - - partition@0 { - label = "U-Boot"; - reg = <0 0x800000>; - }; - partition@800000 { - label = "Linux"; - reg = <0x800000 0x800000>; - }; - partition@1000000 { - label = "Filesystem"; - reg = <0x1000000 0x3f000000>; - }; - }; }; }; @@ -288,3 +267,34 @@ marvell,function = "gpio"; }; }; + +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x800000>; + }; + partition@800000 { + label = "Linux"; + reg = <0x800000 0x800000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi b/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi index a5206db0ebbd..b52634ecf1d9 100644 --- a/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi +++ b/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi @@ -66,33 +66,6 @@ interrupts = <110>; }; }; - - nand@d0000 { - status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partition@0 { - label = "u-boot"; - reg = <0x0 0x300000>; - }; - partition@300000 { - label = "device-tree"; - reg = <0x300000 0x20000>; - }; - partition@320000 { - label = "linux"; - reg = <0x320000 0x2000000>; - }; - partition@2320000 { - label = "rootfs"; - reg = <0x2320000 0xdce0000>; - }; - }; }; }; @@ -227,3 +200,40 @@ marvell,function = "gpio"; }; }; + +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x300000>; + }; + partition@300000 { + label = "device-tree"; + reg = <0x300000 0x20000>; + }; + partition@320000 { + label = "linux"; + reg = <0x320000 0x2000000>; + }; + partition@2320000 { + label = "rootfs"; + reg = <0x2320000 0xdce0000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi index 11fc3271dad4..c15f5e92f97f 100644 --- a/arch/arm/boot/dts/armada-370-xp.dtsi +++ b/arch/arm/boot/dts/armada-370-xp.dtsi @@ -244,11 +244,11 @@ status = "disabled"; }; - nand: nand@d0000 { - compatible = "marvell,armada370-nand"; + nand_controller: nand-controller@d0000 { + compatible = "marvell,armada370-nand-controller"; reg = <0xd0000 0x54>; #address-cells = <1>; - #size-cells = <1>; + #size-cells = <0>; interrupts = <113>; clocks = <&coredivclk 0>; status = "disabled"; diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts index e4ecd7e75644..0e679465cbb5 100644 --- a/arch/arm/boot/dts/armada-375-db.dts +++ b/arch/arm/boot/dts/armada-375-db.dts @@ -103,28 +103,38 @@ nr-ports = <2>; }; -&nand { +&nand_controller { + status = "okay"; pinctrl-0 = <&nand_pins>; pinctrl-names = "default"; - status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partition@0 { - label = "U-Boot"; - reg = <0 0x800000>; - }; - partition@800000 { - label = "Linux"; - reg = <0x800000 0x800000>; - }; - partition@1000000 { - label = "Filesystem"; - reg = <0x1000000 0x3f000000>; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x800000>; + }; + partition@800000 { + label = "Linux"; + reg = <0x800000 0x800000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; }; }; diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi index 53ead6f26a0e..2932a29ae272 100644 --- a/arch/arm/boot/dts/armada-375.dtsi +++ b/arch/arm/boot/dts/armada-375.dtsi @@ -502,11 +502,11 @@ status = "disabled"; }; - nand: nand@d0000 { - compatible = "marvell,armada370-nand"; + nand_controller: nand-controller@d0000 { + compatible = "marvell,armada370-nand-controller"; reg = <0xd0000 0x54>; #address-cells = <1>; - #size-cells = <1>; + #size-cells = <0>; interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gateclk 11>; status = "disabled"; diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/armada-385-db-ap.dts index d294f24281a5..0e4613bb56ee 100644 --- a/arch/arm/boot/dts/armada-385-db-ap.dts +++ b/arch/arm/boot/dts/armada-385-db-ap.dts @@ -135,39 +135,6 @@ status = "okay"; }; - nfc: flash@d0000 { - status = "okay"; - num-cs = <1>; - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "U-Boot"; - reg = <0x00000000 0x00800000>; - read-only; - }; - - partition@800000 { - label = "uImage"; - reg = <0x00800000 0x00400000>; - read-only; - }; - - partition@c00000 { - label = "Root"; - reg = <0x00c00000 0x3f400000>; - }; - }; - }; - usb3@f0000 { status = "okay"; usb-phy = <&usb3_phy>; @@ -233,3 +200,39 @@ spi-max-frequency = <54000000>; }; }; + +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0x00000000 0x00800000>; + read-only; + }; + + partition@800000 { + label = "uImage"; + reg = <0x00800000 0x00400000>; + read-only; + }; + + partition@c00000 { + label = "Root"; + reg = <0x00c00000 0x3f400000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-385-linksys-caiman.dts b/arch/arm/boot/dts/armada-385-linksys-caiman.dts index 1f30993af405..a03050c97084 100644 --- a/arch/arm/boot/dts/armada-385-linksys-caiman.dts +++ b/arch/arm/boot/dts/armada-385-linksys-caiman.dts @@ -73,67 +73,72 @@ &nand { /* 128MiB */ - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x200000>; /* 2MiB */ - read-only; - }; - - partition@100000 { - label = "u_env"; - reg = <0x200000 0x40000>; /* 256KiB */ - }; - - partition@140000 { - label = "s_env"; - reg = <0x240000 0x40000>; /* 256KiB */ - }; - - partition@900000 { - label = "devinfo"; - reg = <0x900000 0x100000>; /* 1MiB */ - read-only; - }; - - /* kernel1 overlaps with rootfs1 by design */ - partition@a00000 { - label = "kernel1"; - reg = <0xa00000 0x2800000>; /* 40MiB */ - }; - - partition@1000000 { - label = "rootfs1"; - reg = <0x1000000 0x2200000>; /* 34MiB */ - }; - - /* kernel2 overlaps with rootfs2 by design */ - partition@3200000 { - label = "kernel2"; - reg = <0x3200000 0x2800000>; /* 40MiB */ - }; - - partition@3800000 { - label = "rootfs2"; - reg = <0x3800000 0x2200000>; /* 34MiB */ - }; - - /* - * 38MiB, last MiB is for the BBT, not writable - */ - partition@5a00000 { - label = "syscfg"; - reg = <0x5a00000 0x2600000>; - }; - - /* - * Unused area between "s_env" and "devinfo". - * Moved here because otherwise the renumbered - * partitions would break the bootloader - * supplied bootargs - */ - partition@180000 { - label = "unused_area"; - reg = <0x280000 0x680000>; /* 6.5MiB */ + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x200000>; /* 2MiB */ + read-only; + }; + + partition@100000 { + label = "u_env"; + reg = <0x200000 0x40000>; /* 256KiB */ + }; + + partition@140000 { + label = "s_env"; + reg = <0x240000 0x40000>; /* 256KiB */ + }; + + partition@900000 { + label = "devinfo"; + reg = <0x900000 0x100000>; /* 1MiB */ + read-only; + }; + + /* kernel1 overlaps with rootfs1 by design */ + partition@a00000 { + label = "kernel1"; + reg = <0xa00000 0x2800000>; /* 40MiB */ + }; + + partition@1000000 { + label = "rootfs1"; + reg = <0x1000000 0x2200000>; /* 34MiB */ + }; + + /* kernel2 overlaps with rootfs2 by design */ + partition@3200000 { + label = "kernel2"; + reg = <0x3200000 0x2800000>; /* 40MiB */ + }; + + partition@3800000 { + label = "rootfs2"; + reg = <0x3800000 0x2200000>; /* 34MiB */ + }; + + /* + * 38MiB, last MiB is for the BBT, not writable + */ + partition@5a00000 { + label = "syscfg"; + reg = <0x5a00000 0x2600000>; + }; + + /* + * Unused area between "s_env" and "devinfo". + * Moved here because otherwise the renumbered + * partitions would break the bootloader + * supplied bootargs + */ + partition@180000 { + label = "unused_area"; + reg = <0x280000 0x680000>; /* 6.5MiB */ + }; }; }; diff --git a/arch/arm/boot/dts/armada-385-linksys-cobra.dts b/arch/arm/boot/dts/armada-385-linksys-cobra.dts index bc34802ce6bc..e3e4877a6f49 100644 --- a/arch/arm/boot/dts/armada-385-linksys-cobra.dts +++ b/arch/arm/boot/dts/armada-385-linksys-cobra.dts @@ -73,67 +73,72 @@ &nand { /* 128MiB */ - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x200000>; /* 2MiB */ - read-only; - }; - - partition@100000 { - label = "u_env"; - reg = <0x200000 0x40000>; /* 256KiB */ - }; - - partition@140000 { - label = "s_env"; - reg = <0x240000 0x40000>; /* 256KiB */ - }; - - partition@900000 { - label = "devinfo"; - reg = <0x900000 0x100000>; /* 1MiB */ - read-only; - }; - - /* kernel1 overlaps with rootfs1 by design */ - partition@a00000 { - label = "kernel1"; - reg = <0xa00000 0x2800000>; /* 40MiB */ - }; - - partition@1000000 { - label = "rootfs1"; - reg = <0x1000000 0x2200000>; /* 34MiB */ - }; - - /* kernel2 overlaps with rootfs2 by design */ - partition@3200000 { - label = "kernel2"; - reg = <0x3200000 0x2800000>; /* 40MiB */ - }; - - partition@3800000 { - label = "rootfs2"; - reg = <0x3800000 0x2200000>; /* 34MiB */ - }; - - /* - * 38MiB, last MiB is for the BBT, not writable - */ - partition@5a00000 { - label = "syscfg"; - reg = <0x5a00000 0x2600000>; - }; - - /* - * Unused area between "s_env" and "devinfo". - * Moved here because otherwise the renumbered - * partitions would break the bootloader - * supplied bootargs - */ - partition@180000 { - label = "unused_area"; - reg = <0x280000 0x680000>; /* 6.5MiB */ + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x200000>; /* 2MiB */ + read-only; + }; + + partition@100000 { + label = "u_env"; + reg = <0x200000 0x40000>; /* 256KiB */ + }; + + partition@140000 { + label = "s_env"; + reg = <0x240000 0x40000>; /* 256KiB */ + }; + + partition@900000 { + label = "devinfo"; + reg = <0x900000 0x100000>; /* 1MiB */ + read-only; + }; + + /* kernel1 overlaps with rootfs1 by design */ + partition@a00000 { + label = "kernel1"; + reg = <0xa00000 0x2800000>; /* 40MiB */ + }; + + partition@1000000 { + label = "rootfs1"; + reg = <0x1000000 0x2200000>; /* 34MiB */ + }; + + /* kernel2 overlaps with rootfs2 by design */ + partition@3200000 { + label = "kernel2"; + reg = <0x3200000 0x2800000>; /* 40MiB */ + }; + + partition@3800000 { + label = "rootfs2"; + reg = <0x3800000 0x2200000>; /* 34MiB */ + }; + + /* + * 38MiB, last MiB is for the BBT, not writable + */ + partition@5a00000 { + label = "syscfg"; + reg = <0x5a00000 0x2600000>; + }; + + /* + * Unused area between "s_env" and "devinfo". + * Moved here because otherwise the renumbered + * partitions would break the bootloader + * supplied bootargs + */ + partition@180000 { + label = "unused_area"; + reg = <0x280000 0x680000>; /* 6.5MiB */ + }; }; }; diff --git a/arch/arm/boot/dts/armada-385-linksys-rango.dts b/arch/arm/boot/dts/armada-385-linksys-rango.dts index 5b745a0ccce5..3c4af57ec2b9 100644 --- a/arch/arm/boot/dts/armada-385-linksys-rango.dts +++ b/arch/arm/boot/dts/armada-385-linksys-rango.dts @@ -81,74 +81,79 @@ &nand { /* AMD/Spansion S34ML02G2 256MiB, OEM Layout */ - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x200000>; /* 2MiB */ - read-only; - }; - - partition@200000 { - label = "u_env"; - reg = <0x200000 0x20000>; /* 128KiB */ - }; - - partition@220000 { - label = "s_env"; - reg = <0x220000 0x40000>; /* 256KiB */ - }; - - partition@7e0000 { - label = "devinfo"; - reg = <0x7e0000 0x40000>; /* 256KiB */ - read-only; - }; - - partition@820000 { - label = "sysdiag"; - reg = <0x820000 0x1e0000>; /* 1920KiB */ - read-only; - }; - - /* kernel1 overlaps with rootfs1 by design */ - partition@a00000 { - label = "kernel1"; - reg = <0xa00000 0x5000000>; /* 80MiB */ - }; - - partition@1000000 { - label = "rootfs1"; - reg = <0x1000000 0x4a00000>; /* 74MiB */ - }; - - /* kernel2 overlaps with rootfs2 by design */ - partition@5a00000 { - label = "kernel2"; - reg = <0x5a00000 0x5000000>; /* 80MiB */ - }; - - partition@6000000 { - label = "rootfs2"; - reg = <0x6000000 0x4a00000>; /* 74MiB */ - }; - - /* - * 86MiB, last MiB is for the BBT, not writable - */ - partition@aa00000 { - label = "syscfg"; - reg = <0xaa00000 0x5600000>; - }; - - /* - * Unused area between "s_env" and "devinfo". - * Moved here because otherwise the renumbered - * partitions would break the bootloader - * supplied bootargs - */ - partition@180000 { - label = "unused_area"; - reg = <0x260000 0x5c0000>; /* 5.75MiB */ + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x200000>; /* 2MiB */ + read-only; + }; + + partition@200000 { + label = "u_env"; + reg = <0x200000 0x20000>; /* 128KiB */ + }; + + partition@220000 { + label = "s_env"; + reg = <0x220000 0x40000>; /* 256KiB */ + }; + + partition@7e0000 { + label = "devinfo"; + reg = <0x7e0000 0x40000>; /* 256KiB */ + read-only; + }; + + partition@820000 { + label = "sysdiag"; + reg = <0x820000 0x1e0000>; /* 1920KiB */ + read-only; + }; + + /* kernel1 overlaps with rootfs1 by design */ + partition@a00000 { + label = "kernel1"; + reg = <0xa00000 0x5000000>; /* 80MiB */ + }; + + partition@1000000 { + label = "rootfs1"; + reg = <0x1000000 0x4a00000>; /* 74MiB */ + }; + + /* kernel2 overlaps with rootfs2 by design */ + partition@5a00000 { + label = "kernel2"; + reg = <0x5a00000 0x5000000>; /* 80MiB */ + }; + + partition@6000000 { + label = "rootfs2"; + reg = <0x6000000 0x4a00000>; /* 74MiB */ + }; + + /* + * 86MiB, last MiB is for the BBT, not writable + */ + partition@aa00000 { + label = "syscfg"; + reg = <0xaa00000 0x5600000>; + }; + + /* + * Unused area between "s_env" and "devinfo". + * Moved here because otherwise the renumbered + * partitions would break the bootloader + * supplied bootargs + */ + partition@180000 { + label = "unused_area"; + reg = <0x260000 0x5c0000>; /* 5.75MiB */ + }; }; }; diff --git a/arch/arm/boot/dts/armada-385-linksys-shelby.dts b/arch/arm/boot/dts/armada-385-linksys-shelby.dts index 44f5aeb5fc33..3451cd3e5dff 100644 --- a/arch/arm/boot/dts/armada-385-linksys-shelby.dts +++ b/arch/arm/boot/dts/armada-385-linksys-shelby.dts @@ -73,67 +73,72 @@ &nand { /* 128MiB */ - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x200000>; /* 2MiB */ - read-only; - }; - - partition@100000 { - label = "u_env"; - reg = <0x200000 0x40000>; /* 256KiB */ - }; - - partition@140000 { - label = "s_env"; - reg = <0x240000 0x40000>; /* 256KiB */ - }; - - partition@900000 { - label = "devinfo"; - reg = <0x900000 0x100000>; /* 1MiB */ - read-only; - }; - - /* kernel1 overlaps with rootfs1 by design */ - partition@a00000 { - label = "kernel1"; - reg = <0xa00000 0x2800000>; /* 40MiB */ - }; - - partition@1000000 { - label = "rootfs1"; - reg = <0x1000000 0x2200000>; /* 34MiB */ - }; - - /* kernel2 overlaps with rootfs2 by design */ - partition@3200000 { - label = "kernel2"; - reg = <0x3200000 0x2800000>; /* 40MiB */ - }; - - partition@3800000 { - label = "rootfs2"; - reg = <0x3800000 0x2200000>; /* 34MiB */ - }; - - /* - * 38MiB, last MiB is for the BBT, not writable - */ - partition@5a00000 { - label = "syscfg"; - reg = <0x5a00000 0x2600000>; - }; - - /* - * Unused area between "s_env" and "devinfo". - * Moved here because otherwise the renumbered - * partitions would break the bootloader - * supplied bootargs - */ - partition@180000 { - label = "unused_area"; - reg = <0x280000 0x680000>; /* 6.5MiB */ + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x200000>; /* 2MiB */ + read-only; + }; + + partition@100000 { + label = "u_env"; + reg = <0x200000 0x40000>; /* 256KiB */ + }; + + partition@140000 { + label = "s_env"; + reg = <0x240000 0x40000>; /* 256KiB */ + }; + + partition@900000 { + label = "devinfo"; + reg = <0x900000 0x100000>; /* 1MiB */ + read-only; + }; + + /* kernel1 overlaps with rootfs1 by design */ + partition@a00000 { + label = "kernel1"; + reg = <0xa00000 0x2800000>; /* 40MiB */ + }; + + partition@1000000 { + label = "rootfs1"; + reg = <0x1000000 0x2200000>; /* 34MiB */ + }; + + /* kernel2 overlaps with rootfs2 by design */ + partition@3200000 { + label = "kernel2"; + reg = <0x3200000 0x2800000>; /* 40MiB */ + }; + + partition@3800000 { + label = "rootfs2"; + reg = <0x3800000 0x2200000>; /* 34MiB */ + }; + + /* + * 38MiB, last MiB is for the BBT, not writable + */ + partition@5a00000 { + label = "syscfg"; + reg = <0x5a00000 0x2600000>; + }; + + /* + * Unused area between "s_env" and "devinfo". + * Moved here because otherwise the renumbered + * partitions would break the bootloader + * supplied bootargs + */ + partition@180000 { + label = "unused_area"; + reg = <0x280000 0x680000>; /* 6.5MiB */ + }; }; }; diff --git a/arch/arm/boot/dts/armada-385-linksys.dtsi b/arch/arm/boot/dts/armada-385-linksys.dtsi index 4a0d7360110b..827e82be2201 100644 --- a/arch/arm/boot/dts/armada-385-linksys.dtsi +++ b/arch/arm/boot/dts/armada-385-linksys.dtsi @@ -138,13 +138,19 @@ }; }; -&nand { +&nand_controller { /* 128MiB or 256MiB */ status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; + #address-cells = <1>; + #size-cells = <0>; + + nand: nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + }; }; &mdio { diff --git a/arch/arm/boot/dts/armada-388-db.dts b/arch/arm/boot/dts/armada-388-db.dts index 05250d426dc4..a2bec07bf4c5 100644 --- a/arch/arm/boot/dts/armada-388-db.dts +++ b/arch/arm/boot/dts/armada-388-db.dts @@ -91,29 +91,6 @@ status = "okay"; }; - flash@d0000 { - status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partition@0 { - label = "U-Boot"; - reg = <0 0x800000>; - }; - partition@800000 { - label = "Linux"; - reg = <0x800000 0x800000>; - }; - partition@1000000 { - label = "Filesystem"; - reg = <0x1000000 0x3f000000>; - }; - }; - sdhci@d8000 { broken-cd; wp-inverted; @@ -165,3 +142,35 @@ }; }; +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x800000>; + }; + partition@800000 { + label = "Linux"; + reg = <0x800000 0x800000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi index 4cc09e43eea2..18edc9bc7927 100644 --- a/arch/arm/boot/dts/armada-38x.dtsi +++ b/arch/arm/boot/dts/armada-38x.dtsi @@ -163,7 +163,7 @@ }; uart0: serial@12000 { - compatible = "snps,dw-apb-uart"; + compatible = "marvell,armada-38x-uart"; reg = <0x12000 0x100>; reg-shift = <2>; interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; @@ -173,7 +173,7 @@ }; uart1: serial@12100 { - compatible = "snps,dw-apb-uart"; + compatible = "marvell,armada-38x-uart"; reg = <0x12100 0x100>; reg-shift = <2>; interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; @@ -551,11 +551,11 @@ status = "okay"; }; - nand: flash@d0000 { - compatible = "marvell,armada370-nand"; + nand_controller: nand-controller@d0000 { + compatible = "marvell,armada370-nand-controller"; reg = <0xd0000 0x54>; #address-cells = <1>; - #size-cells = <1>; + #size-cells = <0>; interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; clocks = <&coredivclk 0>; status = "disabled"; diff --git a/arch/arm/boot/dts/armada-390-db.dts b/arch/arm/boot/dts/armada-390-db.dts index 1b2362e4c831..0e29474ae9a2 100644 --- a/arch/arm/boot/dts/armada-390-db.dts +++ b/arch/arm/boot/dts/armada-390-db.dts @@ -49,37 +49,6 @@ status = "okay"; }; - flash@d0000 { - status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - nand-ecc-strength = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "U-Boot"; - reg = <0 0x800000>; - }; - partition@800000 { - label = "Linux"; - reg = <0x800000 0x800000>; - }; - partition@1000000 { - label = "Filesystem"; - reg = <0x1000000 0x3f000000>; - }; - }; - }; - /* CON98 */ usb3@f8000 { status = "okay"; @@ -136,3 +105,38 @@ }; }; }; + +&nand_controller { + status = "okay"; + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x800000>; + }; + partition@800000 { + label = "Linux"; + reg = <0x800000 0x800000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-395-gp.dts b/arch/arm/boot/dts/armada-395-gp.dts index 2a9de192b423..6dd9e9077f84 100644 --- a/arch/arm/boot/dts/armada-395-gp.dts +++ b/arch/arm/boot/dts/armada-395-gp.dts @@ -57,41 +57,6 @@ status = "okay"; }; - flash@d0000 { - status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "U-Boot"; - reg = <0x00000000 0x00600000>; - read-only; - }; - - partition@800000 { - label = "uImage"; - reg = <0x00600000 0x00400000>; - read-only; - }; - - partition@1000000 { - label = "Root"; - reg = <0x00a00000 0x3f600000>; - }; - }; - }; - /* CON18 */ sdhci@d8000 { clock-frequency = <200000000>; @@ -130,3 +95,42 @@ }; }; }; + +&nand_controller { + status = "okay"; + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0x00000000 0x00600000>; + read-only; + }; + + partition@800000 { + label = "uImage"; + reg = <0x00600000 0x00400000>; + read-only; + }; + + partition@1000000 { + label = "Root"; + reg = <0x00a00000 0x3f600000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-398-db.dts b/arch/arm/boot/dts/armada-398-db.dts index 2337f24784f7..fc28308e5bc5 100644 --- a/arch/arm/boot/dts/armada-398-db.dts +++ b/arch/arm/boot/dts/armada-398-db.dts @@ -51,31 +51,6 @@ status = "okay"; }; - flash@d0000 { - status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - nand-ecc-strength = <8>; - nand-ecc-step-size = <512>; - - partition@0 { - label = "U-Boot"; - reg = <0 0x800000>; - }; - partition@800000 { - label = "Linux"; - reg = <0x800000 0x800000>; - }; - partition@1000000 { - label = "Filesystem"; - reg = <0x1000000 0x3f000000>; - }; - }; - usb3@f8000 { status = "okay"; }; @@ -122,3 +97,38 @@ }; }; }; + +&nand_controller { + status = "okay"; + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x800000>; + }; + partition@800000 { + label = "Linux"; + reg = <0x800000 0x800000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/armada-39x.dtsi index c1737c0a8325..f0c949831efb 100644 --- a/arch/arm/boot/dts/armada-39x.dtsi +++ b/arch/arm/boot/dts/armada-39x.dtsi @@ -367,11 +367,11 @@ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; }; - flash@d0000 { - compatible = "marvell,armada370-nand"; + nand_controller: nand-controller@d0000 { + compatible = "marvell,armada370-nand-controller"; reg = <0xd0000 0x54>; #address-cells = <1>; - #size-cells = <1>; + #size-cells = <0>; interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; clocks = <&coredivclk 0>; status = "disabled"; diff --git a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi index a5da44fb35ed..8d708cc22495 100644 --- a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi +++ b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi @@ -306,6 +306,19 @@ &pinctrl { compatible = "marvell,98dx3236-pinctrl"; + nand_pins: nand-pins { + marvell,pins = "mpp20", "mpp21", "mpp22", + "mpp23", "mpp24", "mpp25", + "mpp26", "mpp27", "mpp28", + "mpp29", "mpp30"; + marvell,function = "dev"; + }; + + nand_rb: nand-rb { + marvell,pins = "mpp19"; + marvell,function = "nand"; + }; + spi0_pins: spi0-pins { marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3"; diff --git a/arch/arm/boot/dts/armada-xp-db-dxbc2.dts b/arch/arm/boot/dts/armada-xp-db-dxbc2.dts index 4c64923f1c52..f42fc6118b7c 100644 --- a/arch/arm/boot/dts/armada-xp-db-dxbc2.dts +++ b/arch/arm/boot/dts/armada-xp-db-dxbc2.dts @@ -70,9 +70,9 @@ &nand { status = "okay"; + label = "pxa3xx_nand-0"; num-cs = <1>; marvell,nand-keep-config; - marvell,nand-enable-arbiter; nand-on-flash-bbt; nand-ecc-strength = <4>; nand-ecc-step-size = <512>; diff --git a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts b/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts index a0ebb52683f1..8432f517e346 100644 --- a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts +++ b/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts @@ -69,9 +69,9 @@ &nand { status = "okay"; + label = "pxa3xx_nand-0"; num-cs = <1>; marvell,nand-keep-config; - marvell,nand-enable-arbiter; nand-on-flash-bbt; nand-ecc-strength = <4>; nand-ecc-step-size = <512>; diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts index 73d3f5cb9828..f3ac7483afed 100644 --- a/arch/arm/boot/dts/armada-xp-db.dts +++ b/arch/arm/boot/dts/armada-xp-db.dts @@ -146,9 +146,9 @@ nand@d0000 { status = "okay"; + label = "pxa3xx_nand-0"; num-cs = <1>; marvell,nand-keep-config; - marvell,nand-enable-arbiter; nand-on-flash-bbt; partitions { diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts index c143556bbb7b..1139e9469a83 100644 --- a/arch/arm/boot/dts/armada-xp-gp.dts +++ b/arch/arm/boot/dts/armada-xp-gp.dts @@ -162,9 +162,9 @@ nand@d0000 { status = "okay"; + label = "pxa3xx_nand-0"; num-cs = <1>; marvell,nand-keep-config; - marvell,nand-enable-arbiter; nand-on-flash-bbt; }; }; diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts index def62e9e835b..bbbb38888bb8 100644 --- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts +++ b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts @@ -83,9 +83,9 @@ nand@d0000 { status = "okay"; + label = "pxa3xx_nand-0"; num-cs = <1>; marvell,nand-keep-config; - marvell,nand-enable-arbiter; nand-on-flash-bbt; partitions { diff --git a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts index f8b60d937818..7a2606c3b62e 100644 --- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts +++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts @@ -165,79 +165,6 @@ bm@c8000 { status = "okay"; }; - - nand@d0000 { - status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; /* 1MB */ - read-only; - }; - - partition@100000 { - label = "u_env"; - reg = <0x100000 0x40000>; /* 256KB */ - }; - - partition@140000 { - label = "s_env"; - reg = <0x140000 0x40000>; /* 256KB */ - }; - - partition@900000 { - label = "devinfo"; - reg = <0x900000 0x100000>; /* 1MB */ - read-only; - }; - - /* kernel1 overlaps with rootfs1 by design */ - partition@a00000 { - label = "kernel1"; - reg = <0xa00000 0x2800000>; /* 40MB */ - }; - - partition@d00000 { - label = "rootfs1"; - reg = <0xd00000 0x2500000>; /* 37MB */ - }; - - /* kernel2 overlaps with rootfs2 by design */ - partition@3200000 { - label = "kernel2"; - reg = <0x3200000 0x2800000>; /* 40MB */ - }; - - partition@3500000 { - label = "rootfs2"; - reg = <0x3500000 0x2500000>; /* 37MB */ - }; - - /* - * 38MB, last MB is for the BBT, not writable - */ - partition@5a00000 { - label = "syscfg"; - reg = <0x5a00000 0x2600000>; - }; - - /* - * Unused area between "s_env" and "devinfo". - * Moved here because otherwise the renumbered - * partitions would break the bootloader - * supplied bootargs - */ - partition@180000 { - label = "unused_area"; - reg = <0x180000 0x780000>; /* 7.5MB */ - }; - }; }; bm-bppi { @@ -434,3 +361,86 @@ }; }; }; + +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; /* 1MB */ + read-only; + }; + + partition@100000 { + label = "u_env"; + reg = <0x100000 0x40000>; /* 256KB */ + }; + + partition@140000 { + label = "s_env"; + reg = <0x140000 0x40000>; /* 256KB */ + }; + + partition@900000 { + label = "devinfo"; + reg = <0x900000 0x100000>; /* 1MB */ + read-only; + }; + + /* kernel1 overlaps with rootfs1 by design */ + partition@a00000 { + label = "kernel1"; + reg = <0xa00000 0x2800000>; /* 40MB */ + }; + + partition@d00000 { + label = "rootfs1"; + reg = <0xd00000 0x2500000>; /* 37MB */ + }; + + /* kernel2 overlaps with rootfs2 by design */ + partition@3200000 { + label = "kernel2"; + reg = <0x3200000 0x2800000>; /* 40MB */ + }; + + partition@3500000 { + label = "rootfs2"; + reg = <0x3500000 0x2500000>; /* 37MB */ + }; + + /* + * 38MB, last MB is for the BBT, not writable + */ + partition@5a00000 { + label = "syscfg"; + reg = <0x5a00000 0x2600000>; + }; + + /* + * Unused area between "s_env" and "devinfo". + * Moved here because otherwise the renumbered + * partitions would break the bootloader + * supplied bootargs + */ + partition@180000 { + label = "unused_area"; + reg = <0x180000 0x780000>; /* 7.5MB */ + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts index c350b1cf5201..8ea73587db81 100644 --- a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts +++ b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts @@ -117,46 +117,6 @@ nr-ports = <2>; status = "okay"; }; - - nand@d0000 { - status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - - /* Use Hardware BCH ECC */ - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x180000>; /* 1.5MB */ - read-only; - }; - - partition@180000 { - label = "u-boot-env"; - reg = <0x180000 0x20000>; /* 128KB */ - read-only; - }; - - partition@200000 { - label = "uImage"; - reg = <0x0200000 0x600000>; /* 6MB */ - }; - - partition@800000 { - label = "minirootfs"; - reg = <0x0800000 0x400000>; /* 4MB */ - }; - - /* Last MB is for the BBT, i.e. not writable */ - partition@c00000 { - label = "ubifs"; - reg = <0x0c00000 0x7400000>; /* 116MB */ - }; - }; }; }; @@ -345,3 +305,53 @@ marvell,function = "gpio"; }; }; + +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + + /* Use Hardware BCH ECC */ + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x180000>; /* 1.5MB */ + read-only; + }; + + partition@180000 { + label = "u-boot-env"; + reg = <0x180000 0x20000>; /* 128KB */ + read-only; + }; + + partition@200000 { + label = "uImage"; + reg = <0x0200000 0x600000>; /* 6MB */ + }; + + partition@800000 { + label = "minirootfs"; + reg = <0x0800000 0x400000>; /* 4MB */ + }; + + /* Last MB is for the BBT, i.e. not writable */ + partition@c00000 { + label = "ubifs"; + reg = <0x0c00000 0x7400000>; /* 116MB */ + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/aspeed-ast2500-evb.dts b/arch/arm/boot/dts/aspeed-ast2500-evb.dts index 91a36c1f029b..ede11c597673 100644 --- a/arch/arm/boot/dts/aspeed-ast2500-evb.dts +++ b/arch/arm/boot/dts/aspeed-ast2500-evb.dts @@ -79,3 +79,21 @@ reg = <0x4d>; }; }; + +&ehci0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb2ah_default>; +}; + +&ehci1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb2bh_default>; +}; + +&uhci { + status = "okay"; + + /* No pinctrl, this follows the above EHCI settings */ +}; diff --git a/arch/arm/boot/dts/aspeed-bmc-intel-s2600wf.dts b/arch/arm/boot/dts/aspeed-bmc-intel-s2600wf.dts new file mode 100644 index 000000000000..7a291de02543 --- /dev/null +++ b/arch/arm/boot/dts/aspeed-bmc-intel-s2600wf.dts @@ -0,0 +1,129 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2017 Intel Corporation +/dts-v1/; + +#include "aspeed-g5.dtsi" + +/ { + model = "S2600WF BMC"; + compatible = "intel,s2600wf-bmc", "aspeed,ast2500"; + + chosen { + stdout-path = &uart5; + bootargs = "earlyprintk"; + }; + + memory { + reg = <0x80000000 0x20000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + vga_memory: framebuffer@7f000000 { + no-map; + reg = <0x7f000000 0x01000000>; + }; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, + <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>, + <&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>, + <&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>; + }; + +}; + +&fmc { + status = "okay"; + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; +#include "openbmc-flash-layout.dtsi" + }; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1_default>; + + flash@0 { + status = "okay"; + m25p,fast-read; + label = "pnor"; + }; +}; + +&uart5 { + status = "okay"; +}; + +&mac0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii1_default>; + use-ncsi; +}; + +&mac1 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>; +}; + +&i2c1 { + status = "okay"; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +&i2c5 { + status = "okay"; +}; + +&i2c6 { + status = "okay"; +}; + +&i2c7 { + status = "okay"; +}; + +&i2c13 { + status = "okay"; +}; + +&gfx { + status = "okay"; +}; + +&pinctrl { + aspeed,external-nodes = <&gfx &lhc>; +}; + +&pwm_tacho { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default + &pinctrl_pwm2_default &pinctrl_pwm3_default + &pinctrl_pwm4_default &pinctrl_pwm5_default + &pinctrl_pwm6_default &pinctrl_pwm7_default>; +}; diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-lanyang.dts b/arch/arm/boot/dts/aspeed-bmc-opp-lanyang.dts new file mode 100644 index 000000000000..d598b6391362 --- /dev/null +++ b/arch/arm/boot/dts/aspeed-bmc-opp-lanyang.dts @@ -0,0 +1,325 @@ +// SPDX-License-Identifier: GPL-2.0+ +// Copyright (c) 2018 Inventec Corporation +/dts-v1/; + +#include "aspeed-g5.dtsi" +#include <dt-bindings/gpio/aspeed-gpio.h> + +/ { + model = "Lanyang BMC"; + compatible = "inventec,lanyang-bmc", "aspeed,ast2500"; + + chosen { + stdout-path = &uart5; + bootargs = "console=ttyS4,115200 earlyprintk"; + }; + + memory { + reg = <0x80000000 0x40000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + flash_memory: region@98000000 { + no-map; + reg = <0x98000000 0x04000000>; /* 64M */ + }; + }; + + leds { + compatible = "gpio-leds"; + + sys_boot_status { + label = "System_boot_status"; + gpios = <&gpio ASPEED_GPIO(B, 6) GPIO_ACTIVE_LOW>; + }; + + attention { + label = "Attention_locator"; + gpios = <&gpio ASPEED_GPIO(B, 7) GPIO_ACTIVE_HIGH>; + }; + + plt_fault { + label = "Platform_fault"; + gpios = <&gpio ASPEED_GPIO(B, 1) GPIO_ACTIVE_HIGH>; + }; + + hdd_fault { + label = "Onboard_drive_fault"; + gpios = <&gpio ASPEED_GPIO(B, 3) GPIO_ACTIVE_HIGH>; + }; + bmc_err { + lable = "BMC_fault"; + gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_HIGH>; + }; + + sys_err { + lable = "Sys_fault"; + gpios = <&gpio ASPEED_GPIO(H, 7) GPIO_ACTIVE_HIGH>; + }; + }; + + fsi: gpio-fsi { + compatible = "fsi-master-gpio", "fsi-master"; + #address-cells = <2>; + #size-cells = <0>; + + clock-gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_HIGH>; + data-gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_HIGH>; + trans-gpios = <&gpio ASPEED_GPIO(D, 5) GPIO_ACTIVE_HIGH>; + enable-gpios = <&gpio ASPEED_GPIO(D, 0) GPIO_ACTIVE_HIGH>; + mux-gpios = <&gpio ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, + <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>, + <&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>, + <&adc 13>, <&adc 14>, <&adc 15>; + }; + + iio-hwmon-battery { + compatible = "iio-hwmon"; + io-channels = <&adc 12>; + }; +}; + +&pwm_tacho { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default + &pinctrl_pwm2_default &pinctrl_pwm3_default>; + + fan@0 { + reg = <0x00>; + aspeed,fan-tach-ch = /bits/ 8 <0x00>; + }; + + fan@1 { + reg = <0x01>; + aspeed,fan-tach-ch = /bits/ 8 <0x01>; + }; + + fan@2 { + reg = <0x02>; + aspeed,fan-tach-ch = /bits/ 8 <0x02>; + }; + + fan@3 { + reg = <0x03>; + aspeed,fan-tach-ch = /bits/ 8 <0x03>; + }; +}; + +&fmc { + status = "okay"; + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; +#include "openbmc-flash-layout.dtsi" + }; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1_default>; + + flash@0 { + status = "okay"; + label = "pnor"; + m25p,fast-read; + }; +}; + +&spi2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi2ck_default + &pinctrl_spi2cs0_default + &pinctrl_spi2cs1_default + &pinctrl_spi2miso_default + &pinctrl_spi2mosi_default>; + + flash@0 { + status = "okay"; + }; +}; + +&uart1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd1_default + &pinctrl_rxd1_default>; +}; + +&lpc_ctrl { + status = "okay"; + memory-region = <&flash_memory>; + flash = <&spi1>; +}; + +&lpc_snoop { + status = "okay"; + snoop-ports = <0x80>; +}; + +&uart5 { + status = "okay"; +}; + +&mac0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii1_default>; + use-ncsi; +}; + +&mac1 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>; +}; + +&i2c0 { + status = "okay"; + + eeprom@55 { + compatible = "atmel,24c64"; + reg = <0x55>; + pagesize = <32>; + }; + + rtc@68 { + compatible = "nxp,pcf8523"; + reg = <0x68>; + }; + + tmp75@48 { + compatible = "ti,tmp75"; + reg = <0x48>; + }; +}; + +&i2c1 { + status = "okay"; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +&i2c5 { + status = "okay"; +}; + +&i2c6 { + status = "okay"; +}; + +&i2c7 { + status = "okay"; +}; + +&i2c8 { + status = "okay"; +}; + +&i2c9 { + status = "okay"; +}; + +&i2c10 { + status = "okay"; +}; + +&i2c11 { + status = "okay"; +}; + +&vuart { + status = "okay"; +}; + +&gfx { + status = "okay"; +}; + +&pinctrl { + aspeed,external-nodes = <&gfx &lhc>; +}; + +&gpio { + pin_gpio_b0 { + gpio-hog; + gpios = <ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>; + output-high; + line-name = "BMC_HDD1_PWR_EN"; + }; + + pin_gpio_b5 { + gpio-hog; + gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>; + input; + line-name = "BMC_USB1_OCI2"; + }; + + pin_gpio_h5 { + gpio-hog; + gpios = <ASPEED_GPIO(H, 5) GPIO_ACTIVE_HIGH>; + output-high; + line-name = "BMC_CP0_PERST_ENABLE_R"; + }; + + pin_gpio_z2 { + gpio-hog; + gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>; + output-high; + line-name = "RST_PCA9546_U177_N"; + }; + + pin_gpio_aa6 { + gpio-hog; + gpios = <ASPEED_GPIO(AA, 6) GPIO_ACTIVE_HIGH>; + output-high; + line-name = "BMC_CP0_RESET_N"; + }; + + pin_gpio_aa7 { + gpio-hog; + gpios = <ASPEED_GPIO(AA, 7) GPIO_ACTIVE_HIGH>; + output-high; + line-name = "BMC_TPM_RESET_N"; + }; + + pin_gpio_ab0 { + gpio-hog; + gpios = <ASPEED_GPIO(AB, 0) GPIO_ACTIVE_LOW>; + output-high; + line-name = "BMC_USB_PWRON_N"; + }; +}; + +&ibt { + status = "okay"; +}; + +&adc { + status = "okay"; +}; + diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts b/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts index 51bc6a2e9dd5..389f5f83bef9 100644 --- a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts +++ b/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts @@ -68,6 +68,12 @@ gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>; linux,code = <ASPEED_GPIO(J, 2)>; }; + + id-button { + label = "id-button"; + gpios = <&gpio ASPEED_GPIO(Q, 7) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(Q, 7)>; + }; }; }; diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts b/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts index 7056231cbee6..78a511e6e482 100644 --- a/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts +++ b/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts @@ -28,6 +28,34 @@ }; }; + gpio-keys { + compatible = "gpio-keys"; + + air-water { + label = "air-water"; + gpios = <&gpio ASPEED_GPIO(B, 5) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(B, 5)>; + }; + + checkstop { + label = "checkstop"; + gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(J, 2)>; + }; + + ps0-presence { + label = "ps0-presence"; + gpios = <&gpio ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(P, 7)>; + }; + + ps1-presence { + label = "ps1-presence"; + gpios = <&gpio ASPEED_GPIO(N, 0) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(N, 0)>; + }; + }; + gpio-keys-polled { compatible = "gpio-keys-polled"; #address-cells = <1>; @@ -547,6 +575,10 @@ pinctrl-0 = <&pinctrl_wdtrst1_default>; }; +&wdt2 { + aspeed,alt-boot; +}; + &ibt { status = "okay"; }; diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts b/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts index ebe726a0d311..ccbf645ab84d 100644 --- a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts +++ b/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts @@ -55,6 +55,12 @@ gpios = <&gpio ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>; linux,code = <ASPEED_GPIO(F, 7)>; }; + + pcie-e2b-present{ + label = "pcie-e2b-present"; + gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(E, 7)>; + }; }; leds { diff --git a/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts b/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts new file mode 100644 index 000000000000..43ed13963d35 --- /dev/null +++ b/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts @@ -0,0 +1,159 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2017 Facebook Inc. +/dts-v1/; + +#include "aspeed-g5.dtsi" +#include <dt-bindings/gpio/aspeed-gpio.h> + +/ { + model = "Portwell Neptune BMC"; + compatible = "portwell,neptune-bmc", "aspeed,ast2500"; + aliases { + serial0 = &uart1; + serial4 = &uart5; + }; + chosen { + stdout-path = &uart5; + bootargs = "console=ttyS4,115200 earlyprintk"; + }; + + memory { + reg = <0x80000000 0x20000000>; + }; + + leds { + compatible = "gpio-leds"; + postcode0 { + label="BMC_UP"; + gpios = <&gpio ASPEED_GPIO(H, 0) GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + postcode1 { + label="BMC_HB"; + gpios = <&gpio ASPEED_GPIO(H, 1) GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + postcode2 { + label="FAULT"; + gpios = <&gpio ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>; + }; + // postcode3-7 are GPIOH3-H7 + }; +}; + +&fmc { + status = "okay"; + flash@0 { + status = "okay"; + m25p,fast-read; +#include "openbmc-flash-layout.dtsi" + }; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1_default>; + flash@0 { + status = "okay"; + m25p,fast-read; + label = "pnor"; + }; +}; + +&uart1 { + // Host Console + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd1_default + &pinctrl_rxd1_default>; +}; + +&uart5 { + // BMC Console + status = "okay"; +}; + +&mac0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii1_default + &pinctrl_mdio1_default>; +}; + +&mac1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii2_default>; + use-ncsi; +}; + +&i2c1 { + status = "okay"; + // To PCIe slot SMBUS +}; + +&i2c2 { + status = "okay"; + // To LAN I210 +}; + +&i2c3 { + status = "okay"; + // SMBus to COMe AB +}; + +&i2c4 { + status = "okay"; + // I2C to COMe AB +}; + +&i2c5 { + status = "okay"; +// USB Debug card + pca9555@27 { + compatible = "nxp,pca9555"; + reg = <0x27>; + }; +}; + +&i2c6 { + status = "okay"; + tpm@20 { + compatible = "infineon,slb9645tt"; + reg = <0x20>; + }; + tmp421@4e { + compatible = "ti,tmp421"; + reg = <0x4e>; + }; + tmp421@4f { + compatible = "ti,tmp421"; + reg = <0x4f>; + }; +}; + +&i2c8 { + status = "okay"; + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + pagesize = <32>; + }; +}; + +&pwm_tacho { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>; + fan@0 { + reg = <0x00>; + aspeed,fan-tach-ch = /bits/ 8 <0x00>; + }; + + fan@1 { + reg = <0x00>; + aspeed,fan-tach-ch = /bits/ 8 <0x01>; + }; +}; diff --git a/arch/arm/boot/dts/aspeed-g4.dtsi b/arch/arm/boot/dts/aspeed-g4.dtsi index 518d2bc7c7fc..75df1573380e 100644 --- a/arch/arm/boot/dts/aspeed-g4.dtsi +++ b/arch/arm/boot/dts/aspeed-g4.dtsi @@ -108,6 +108,23 @@ status = "disabled"; }; + ehci0: usb@1e6a1000 { + compatible = "aspeed,ast2400-ehci", "generic-ehci"; + reg = <0x1e6a1000 0x100>; + interrupts = <5>; + clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>; + status = "disabled"; + }; + + uhci: usb@1e6b0000 { + compatible = "aspeed,ast2400-uhci", "generic-uhci"; + reg = <0x1e6b0000 0x100>; + interrupts = <14>; + #ports = <3>; + clocks = <&syscon ASPEED_CLK_GATE_USBUHCICLK>; + status = "disabled"; + }; + apb { compatible = "simple-bus"; #address-cells = <1>; @@ -125,6 +142,14 @@ pinctrl: pinctrl { compatible = "aspeed,g4-pinctrl"; }; + + }; + + rng: hwrng@1e6e2078 { + compatible = "timeriomem_rng"; + reg = <0x1e6e2078 0x4>; + period = <1>; + quality = <100>; }; adc: adc@1e6e9000 { @@ -1250,6 +1275,16 @@ groups = "USBCKI"; }; + pinctrl_usb2h_default: usb2h_default { + function = "USB2H1"; + groups = "USB2H1"; + }; + + pinctrl_usb2d_default: usb2d_default { + function = "USB2D1"; + groups = "USB2D1"; + }; + pinctrl_vgabios_rom_default: vgabios_rom_default { function = "VGABIOS_ROM"; groups = "VGABIOS_ROM"; diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed-g5.dtsi index f9917717dd08..17f2714d18a7 100644 --- a/arch/arm/boot/dts/aspeed-g5.dtsi +++ b/arch/arm/boot/dts/aspeed-g5.dtsi @@ -143,6 +143,31 @@ status = "disabled"; }; + ehci0: usb@1e6a1000 { + compatible = "aspeed,ast2500-ehci", "generic-ehci"; + reg = <0x1e6a1000 0x100>; + interrupts = <5>; + clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>; + status = "disabled"; + }; + + ehci1: usb@1e6a3000 { + compatible = "aspeed,ast2500-ehci", "generic-ehci"; + reg = <0x1e6a3000 0x100>; + interrupts = <13>; + clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>; + status = "disabled"; + }; + + uhci: usb@1e6b0000 { + compatible = "aspeed,ast2500-uhci", "generic-uhci"; + reg = <0x1e6b0000 0x100>; + interrupts = <14>; + #ports = <2>; + clocks = <&syscon ASPEED_CLK_GATE_USBUHCICLK>; + status = "disabled"; + }; + apb { compatible = "simple-bus"; #address-cells = <1>; @@ -164,6 +189,13 @@ }; }; + rng: hwrng@1e6e2078 { + compatible = "timeriomem_rng"; + reg = <0x1e6e2078 0x4>; + period = <1>; + quality = <100>; + }; + gfx: display@1e6e6000 { compatible = "aspeed,ast2500-gfx", "syscon"; reg = <0x1e6e6000 0x1000>; @@ -1380,6 +1412,21 @@ groups = "USBCKI"; }; + pinctrl_usb2ah_default: usb2ah_default { + function = "USB2AH"; + groups = "USB2AH"; + }; + + pinctrl_usb11bhid_default: usb11bhid_default { + function = "USB11BHID"; + groups = "USB11BHID"; + }; + + pinctrl_usb2bh_default: usb2bh_default { + function = "USB2BH"; + groups = "USB2BH"; + }; + pinctrl_vgabiosrom_default: vgabiosrom_default { function = "VGABIOSROM"; groups = "VGABIOSROM"; diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts index e4bbb7e0f793..fcc85d70f36e 100644 --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts @@ -232,7 +232,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>; interrupt-parent = <&pioA>; - interrupts = <PIN_PB13 GPIO_ACTIVE_LOW>; + interrupts = <PIN_PB13 IRQ_TYPE_EDGE_RISING>; active-semi,chglev-gpios = <&pioA PIN_PA12 GPIO_ACTIVE_HIGH>; active-semi,lbo-gpios = <&pioA PIN_PC8 GPIO_ACTIVE_LOW>; diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/at91-sama5d4ek.dts index 7887a7160a54..0702a2f2b336 100644 --- a/arch/arm/boot/dts/at91-sama5d4ek.dts +++ b/arch/arm/boot/dts/at91-sama5d4ek.dts @@ -129,8 +129,8 @@ wakeup-source; }; - atmel_mxt_ts@4c { - compatible = "atmel,atmel_mxt_ts"; + touchscreen@4c { + compatible = "atmel,maxtouch"; reg = <0x4c>; interrupt-parent = <&pioE>; interrupts = <24 0x0>; diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi index 699fdf94d139..9fe4f5a6379e 100644 --- a/arch/arm/boot/dts/bcm-cygnus.dtsi +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi @@ -69,7 +69,7 @@ timer@20200 { compatible = "arm,cortex-a9-global-timer"; reg = <0x20200 0x100>; - interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>; clocks = <&periph_clk>; }; diff --git a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts index aa1fc7babfea..2cd9c5e4f892 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts @@ -101,6 +101,12 @@ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio14>; diff --git a/arch/arm/boot/dts/bcm2835-rpi-a.dts b/arch/arm/boot/dts/bcm2835-rpi-a.dts index 425f6b0a5ef8..067d1f07a2d3 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-a.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-a.dts @@ -96,6 +96,12 @@ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio14>; diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts index effa195e7895..cfbdaacbaeba 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts @@ -103,6 +103,12 @@ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio14>; diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts index 772ec3b48231..5641d162dfdb 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts @@ -96,6 +96,12 @@ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio14>; diff --git a/arch/arm/boot/dts/bcm2835-rpi-b.dts b/arch/arm/boot/dts/bcm2835-rpi-b.dts index 434483d6fc14..31ff602e2cd3 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-b.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts @@ -91,6 +91,12 @@ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio14>; diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi index 6c3cfaa77f3d..cb2d6d78a7fb 100644 --- a/arch/arm/boot/dts/bcm2835-rpi.dtsi +++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi @@ -83,12 +83,6 @@ bus-width = <4>; }; -&pwm { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; - status = "okay"; -}; - &usb { power-domains = <&power RPI_POWER_DOMAIN_USB>; }; diff --git a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts index 5c339adabdf0..2fef70a09953 100644 --- a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts +++ b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts @@ -41,6 +41,12 @@ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio14>; diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts new file mode 100644 index 000000000000..4adb85e66be3 --- /dev/null +++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts @@ -0,0 +1,108 @@ +// SPDX-License-Identifier: GPL-2.0 +/dts-v1/; +#include "bcm2837.dtsi" +#include "bcm2835-rpi.dtsi" +#include "bcm283x-rpi-lan7515.dtsi" +#include "bcm283x-rpi-usb-host.dtsi" + +/ { + compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837"; + model = "Raspberry Pi 3 Model B+"; + + chosen { + /* 8250 auxiliary UART instead of pl011 */ + stdout-path = "serial1:115200n8"; + }; + + memory { + reg = <0 0x40000000>; + }; + + leds { + act { + gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; + }; + + pwr { + label = "PWR"; + gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; + }; + }; + + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&expgpio 1 GPIO_ACTIVE_HIGH>; + }; +}; + +&firmware { + expgpio: gpio { + compatible = "raspberrypi,firmware-gpio"; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "BT_ON", + "WL_ON", + "STATUS_LED", + "LAN_RUN", + "", + "CAM_GPIO0", + "CAM_GPIO1", + ""; + status = "okay"; + }; +}; + +&hdmi { + hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>; + status = "okay"; +}; + +/* SDHCI is used to control the SDIO for wireless */ +&sdhci { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_gpio34>; + status = "okay"; + bus-width = <4>; + non-removable; + mmc-pwrseq = <&wifi_pwrseq>; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* SDHOST is used to drive the SD card */ +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + status = "okay"; + bus-width = <4>; +}; + +/* uart0 communicates with the BT module */ +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <2000000>; + shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; + }; +}; + +/* uart1 is mapped to the pin header */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_gpio14>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts index 0b31d995a066..c318bcbc6ba7 100644 --- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts +++ b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts @@ -20,9 +20,14 @@ leds { act { - gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; + gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>; }; }; + + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&expgpio 1 GPIO_ACTIVE_HIGH>; + }; }; &firmware { @@ -42,6 +47,16 @@ }; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>; + status = "okay"; +}; + +&hdmi { + hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>; +}; + /* uart0 communicates with the BT module */ &uart0 { pinctrl-names = "default"; @@ -51,6 +66,7 @@ bluetooth { compatible = "brcm,bcm43438-bt"; max-speed = <2000000>; + shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; }; }; @@ -63,11 +79,19 @@ /* SDHCI is used to control the SDIO for wireless */ &sdhci { + #address-cells = <1>; + #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&emmc_gpio34>; status = "okay"; bus-width = <4>; non-removable; + mmc-pwrseq = <&wifi_pwrseq>; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; }; /* SDHOST is used to drive the SD card */ diff --git a/arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi b/arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi new file mode 100644 index 000000000000..9403da0990d0 --- /dev/null +++ b/arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi @@ -0,0 +1,27 @@ +// SPDX-License-Identifier: GPL-2.0 +/ { + aliases { + ethernet0 = ðernet; + }; +}; + +&usb { + usb-port@1 { + compatible = "usb424,2514"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + usb-port@1 { + compatible = "usb424,2514"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ethernet: ethernet@1 { + compatible = "usb424,7800"; + reg = <1>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi index ac00e730f898..61315cf734ef 100644 --- a/arch/arm/boot/dts/bcm283x.dtsi +++ b/arch/arm/boot/dts/bcm283x.dtsi @@ -136,6 +136,7 @@ rng@7e104000 { compatible = "brcm,bcm2835-rng"; reg = <0x7e104000 0x10>; + interrupts = <2 29>; }; mailbox: mailbox@7e00b880 { diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts index 4175174e589a..ff2e551b9058 100644 --- a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts +++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts @@ -1,20 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X ARM platform code. * DTS for Asus RT-AC56U * * Copyright (C) 2015 RafaÅ‚ MiÅ‚ecki <zajec5@gmail.com> - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH - * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY - * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, - * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM - * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE - * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR - * PERFORMANCE OF THIS SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts index 8fa033fea959..3bcc03788f38 100644 --- a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts +++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts @@ -1,20 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X ARM platform code. * DTS for Asus RT-AC68U * * Copyright (C) 2015 RafaÅ‚ MiÅ‚ecki <zajec5@gmail.com> - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH - * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY - * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, - * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM - * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE - * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR - * PERFORMANCE OF THIS SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts index 8b64caabaad8..a587384f8e40 100644 --- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts +++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts @@ -1,10 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X ARM platform code. * DTS for Buffalo WZR-1750DHP * * Copyright (C) 2014 RafaÅ‚ MiÅ‚ecki <zajec5@gmail.com> - * - * Licensed under the GNU/GPL. See COPYING for details. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts b/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts index 126ab5867772..6c8f0ad82332 100644 --- a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts +++ b/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright (C) 2017 RafaÅ‚ MiÅ‚ecki <rafal@milecki.pl> - * - * Licensed under the ISC license. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts b/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts index f591b0f256d8..ebda45fe9ea4 100644 --- a/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts +++ b/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright 2016 Luxul Inc. - * - * Licensed under the ISC license. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts b/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts index 50d65d8fbd9a..9dd0e22c906a 100644 --- a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts +++ b/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts @@ -1,10 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X ARM platform code. * DTS for Luxul XWC-1000 * * Copyright 2014 Luxul Inc. - * - * Licensed under the GNU/GPL. See COPYING for details. */ /dts-v1/; @@ -26,9 +25,15 @@ nand: nand@18028000 { nandcs@0 { - partition@0 { - label = "ubi"; - reg = <0x00000000 0x08000000>; + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ubi"; + reg = <0x00000000 0x08000000>; + }; }; }; }; diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts index bb66cebe0bd8..2642494c97a1 100644 --- a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts +++ b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts @@ -1,20 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X ARM platform code. * DTS for Netgear R6300 V2 * * Copyright (C) 2014 RafaÅ‚ MiÅ‚ecki <zajec5@gmail.com> - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH - * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY - * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, - * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM - * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE - * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR - * PERFORMANCE OF THIS SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts index 83a4c60bb431..e7b09b7b7d25 100644 --- a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts +++ b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts @@ -1,10 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X arm platform code. * DTS for SmartRG SR400ac * * Copyright (C) 2015 RafaÅ‚ MiÅ‚ecki <zajec5@gmail.com> - * - * Licensed under the GNU/GPL. See COPYING for details. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts index 0800a964f2fe..16314fcc6e56 100644 --- a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts +++ b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts @@ -1,20 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X ARM platform code. * DTS for Asus RT-N18U * * Copyright (C) 2014 RafaÅ‚ MiÅ‚ecki <zajec5@gmail.com> - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH - * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY - * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, - * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM - * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE - * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR - * PERFORMANCE OF THIS SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts index c2af33eb47de..328aa90240ce 100644 --- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts +++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts @@ -1,20 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X ARM platform code. * DTS for Buffalo WZR-600DHP2 * * Copyright (C) 2014 RafaÅ‚ MiÅ‚ecki <zajec5@gmail.com> - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH - * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY - * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, - * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM - * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE - * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR - * PERFORMANCE OF THIS SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts index 87ea6ba664f5..8ea46eed26e2 100644 --- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts +++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts @@ -1,20 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X ARM platform code. * DTS for Buffalo WZR-900DHP * * Copyright (C) 2015 RafaÅ‚ MiÅ‚ecki <zajec5@gmail.com> - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH - * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY - * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, - * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM - * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE - * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR - * PERFORMANCE OF THIS SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts b/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts index 9b5759849983..5eeac7302329 100644 --- a/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts +++ b/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright 2017 Luxul Inc. - * - * Licensed under the ISC license. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts b/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts index ba1c19b1b3eb..da4d9ec62fc6 100644 --- a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts +++ b/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright 2017 Luxul Inc. - * - * Licensed under the ISC license. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts b/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts index 3ed8de42cb48..c94c732188fb 100644 --- a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts +++ b/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright (C) 2017 RafaÅ‚ MiÅ‚ecki <rafal@milecki.pl> - * - * Licensed under the ISC license. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts index df473cc41572..22271818f901 100644 --- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts +++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts @@ -1,20 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X ARM platform code. * DTS for Asus RT-AC87U * * Copyright (C) 2015 RafaÅ‚ MiÅ‚ecki <zajec5@gmail.com> - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH - * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY - * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, - * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM - * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE - * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR - * PERFORMANCE OF THIS SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts index 92058c73ee59..79a9633ec417 100644 --- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts +++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts @@ -1,10 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X ARM platform code. * DTS for Buffalo WXR-1900DHP * * Copyright (C) 2015 Felix Fietkau <nbd@openwrt.org> - * - * Licensed under the GNU/GPL. See COPYING for details. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts b/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts index 3d1d9c2c4efc..db744a5e122d 100644 --- a/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts +++ b/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright (C) 2017 RafaÅ‚ MiÅ‚ecki <rafal@milecki.pl> - * - * Licensed under the ISC license. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts index f43ab4721456..9e267d38df4c 100644 --- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts +++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts @@ -1,20 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X ARM platform code. * DTS for Netgear R7000 * * Copyright (C) 2015 RafaÅ‚ MiÅ‚ecki <zajec5@gmail.com> - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH - * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY - * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, - * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM - * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE - * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR - * PERFORMANCE OF THIS SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts b/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts index ec4a50e440f6..f5bf6586ae07 100644 --- a/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts +++ b/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright (C) 2016 RafaÅ‚ MiÅ‚ecki <rafal@milecki.pl> - * - * Licensed under the ISC license. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts index 7cc7d344fe5b..d173bcd93b91 100644 --- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts +++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts @@ -1,20 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X ARM platform code. * DTS for D-Link DIR-885L * * Copyright (C) 2016 RafaÅ‚ MiÅ‚ecki <zajec5@gmail.com> - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH - * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY - * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, - * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM - * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE - * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR - * PERFORMANCE OF THIS SOFTWARE. */ /dts-v1/; @@ -37,9 +26,15 @@ nand: nand@18028000 { nandcs@0 { - partition@0 { - label = "firmware"; - reg = <0x00000000 0x08000000>; + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "firmware"; + reg = <0x00000000 0x08000000>; + }; }; }; }; diff --git a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts index b6750f70dffb..f47afe36d857 100644 --- a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts +++ b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright (C) 2017 RafaÅ‚ MiÅ‚ecki <rafal@milecki.pl> - * - * Licensed under the ISC license. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts b/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts index ecd22a246746..a5cef51cfe4f 100644 --- a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts +++ b/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright (C) 2017 Luxul Inc. - * - * Licensed under the ISC license. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts b/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts new file mode 100644 index 000000000000..7fd85475893d --- /dev/null +++ b/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts @@ -0,0 +1,57 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright 2018 Luxul Inc. + */ + +/dts-v1/; + +#include "bcm47094.dtsi" + +/ { + compatible = "luxul,xap-1610-v1", "brcm,bcm47094", "brcm,bcm4708"; + model = "Luxul XAP-1610 V1"; + + chosen { + bootargs = "earlycon"; + }; + + memory { + reg = <0x00000000 0x08000000>; + }; + + leds { + compatible = "gpio-leds"; + + status { + label = "bcm53xx:green:status"; + gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>; + linux,default-trigger = "timer"; + }; + + 2ghz { + label = "bcm53xx:blue:2ghz"; + gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>; + }; + + 5ghz { + label = "bcm53xx:blue:5ghz"; + gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + restart { + label = "Reset"; + linux,code = <KEY_RESTART>; + gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&spi_nor { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts b/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts index 15ffb1abc440..7496aabf8f77 100644 --- a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts +++ b/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright (C) 2017 Luxul Inc. - * - * Licensed under the ISC license. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts b/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts index bc1d1e10d4ac..53aaa5212610 100644 --- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts +++ b/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright 2016 Luxul Inc. - * - * Licensed under the ISC license. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts b/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts new file mode 100644 index 000000000000..bdad7267255a --- /dev/null +++ b/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts @@ -0,0 +1,77 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright 2018 Luxul Inc. + */ + +/dts-v1/; + +#include "bcm47094.dtsi" +#include "bcm5301x-nand-cs0-bch8.dtsi" + +/ { + compatible = "luxul,xwr-3150-v1", "brcm,bcm47094", "brcm,bcm4708"; + model = "Luxul XWR-3150 V1"; + + chosen { + bootargs = "earlycon"; + }; + + memory { + reg = <0x00000000 0x08000000 + 0x88000000 0x18000000>; + }; + + leds { + compatible = "gpio-leds"; + + power { + label = "bcm53xx:green:power"; + gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-on"; + }; + + usb3 { + label = "bcm53xx:green:usb3"; + gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>; + trigger-sources = <&ohci_port1>, <&ehci_port1>, + <&xhci_port1>; + linux,default-trigger = "usbport"; + }; + + status { + label = "bcm53xx:green:status"; + gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>; + linux,default-trigger = "timer"; + }; + + 2ghz { + label = "bcm53xx:green:2ghz"; + gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>; + }; + + 5ghz { + label = "bcm53xx:green:5ghz"; + gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + restart { + label = "Reset"; + linux,code = <KEY_RESTART>; + gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&usb3 { + vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>; +}; + +&spi_nor { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts index 859929973158..0e718edc065a 100644 --- a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts +++ b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright (C) 2016 RafaÅ‚ MiÅ‚ecki <rafal@milecki.pl> - * - * Licensed under the ISC license. */ /dts-v1/; diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch1.dtsi b/arch/arm/boot/dts/bcm5301x-nand-cs0-bch1.dtsi index 24b099c00f13..c349e8f0afc5 100644 --- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch1.dtsi +++ b/arch/arm/boot/dts/bcm5301x-nand-cs0-bch1.dtsi @@ -1,9 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom Northstar NAND. * * Copyright (C) 2016 RafaÅ‚ MiÅ‚ecki <rafal.milecki@gmail.com> - * - * Licensed under the ISC license. */ #include "bcm5301x-nand-cs0.dtsi" diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi b/arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi index b4e875df9528..18e25e302b13 100644 --- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi +++ b/arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi @@ -1,7 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Copyright 2016 Luxul Inc. - * - * Licensed under the ISC license. */ #include "bcm5301x-nand-cs0.dtsi" diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi b/arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi index 9a9630ded306..c8e56d30bd6f 100644 --- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi +++ b/arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi @@ -1,3 +1,4 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom BCM470X / BCM5301X Nand chip defaults. * @@ -5,8 +6,6 @@ * and uses 8 bit ECC. * * Copyright (C) 2015 Hauke Mehrtens <hauke@hauke-m.de> - * - * Licensed under the GNU/GPL. See COPYING for details. */ #include "bcm5301x-nand-cs0.dtsi" diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi b/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi index 168495106b82..e5a2d62daf92 100644 --- a/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi +++ b/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi @@ -1,9 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* * Broadcom Northstar NAND. * * Copyright (C) 2015 Hauke Mehrtens <hauke@hauke-m.de> - * - * Licensed under the GNU/GPL. See COPYING for details. */ / { diff --git a/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts b/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts index 1c475796d17f..64a297759eb9 100644 --- a/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts +++ b/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts @@ -1,39 +1,8 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) /* * Device Tree file for Sony NSZ-GS7 * * Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/berlin2.dtsi b/arch/arm/boot/dts/berlin2.dtsi index d575823c5750..db67377af266 100644 --- a/arch/arm/boot/dts/berlin2.dtsi +++ b/arch/arm/boot/dts/berlin2.dtsi @@ -1,3 +1,4 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) /* * Device Tree Include file for Marvell Armada 1500 (Berlin BG2) SoC * @@ -5,38 +6,6 @@ * * based on GPL'ed 2.6 kernel sources * (c) Marvell International Ltd. - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. */ #include <dt-bindings/clock/berlin2.h> @@ -149,7 +118,7 @@ local-timer@ad0600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0xad0600 0x20>; - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>; clocks = <&chip_clk CLKID_TWD>; }; diff --git a/arch/arm/boot/dts/berlin2cd-google-chromecast.dts b/arch/arm/boot/dts/berlin2cd-google-chromecast.dts index ca24def0ce13..56fa951bc86f 100644 --- a/arch/arm/boot/dts/berlin2cd-google-chromecast.dts +++ b/arch/arm/boot/dts/berlin2cd-google-chromecast.dts @@ -1,39 +1,8 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) /* * Device Tree file for Google Chromecast * * Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; @@ -52,22 +21,35 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x20000000>; /* 512 MB */ + + /* + * We're using "linux,usable-memory" instead of "reg" here + * because the (signed and encrypted) bootloader that shipped + * with this device provides an incorrect memory range in + * ATAG_MEM. Linux helpfully overrides the "reg" property with + * data from the ATAG, so we can't specify the proper range + * normally. Fortunately, this alternate property is checked + * first by the OF driver, so we can (ab)use it instead. + */ + linux,usable-memory = <0x00000000 0x20000000>; /* 512 MB */ }; leds { - compatible = "gpio-leds"; + compatible = "pwm-leds"; + pinctrl-0 = <&ledpwm_pmux>; + pinctrl-names = "default"; white { label = "white"; - gpios = <&portc 1 GPIO_ACTIVE_HIGH>; - default-state = "keep"; + pwms = <&pwm 0 600000 0>; + max-brightness = <255>; + linux,default-trigger = "default-on"; }; red { label = "red"; - gpios = <&portc 2 GPIO_ACTIVE_HIGH>; - default-state = "keep"; + pwms = <&pwm 1 600000 0>; + max-brightness = <255>; }; }; }; @@ -86,3 +68,10 @@ &usb_phy1 { status = "okay"; }; &usb1 { status = "okay"; }; + +&soc_pinctrl { + ledpwm_pmux: ledpwm-pmux { + groups = "G0"; + function = "pwm"; + }; +}; diff --git a/arch/arm/boot/dts/berlin2cd-valve-steamlink.dts b/arch/arm/boot/dts/berlin2cd-valve-steamlink.dts new file mode 100644 index 000000000000..79ac842ae461 --- /dev/null +++ b/arch/arm/boot/dts/berlin2cd-valve-steamlink.dts @@ -0,0 +1,79 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2018 Alexander Monakov <amonakov@gmail.com> + */ +/dts-v1/; + +#include "berlin2cd.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Valve Steam Link"; + compatible = "valve,steamlink", "marvell,berlin2cd", "marvell,berlin"; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x20000000>; /* 512 MB */ + }; + + gpio-restart { + compatible = "gpio-restart"; + gpios = <&porta 6 GPIO_ACTIVE_HIGH>; + active-delay = <100>; + inactive-delay = <10>; + wait-delay = <100>; + priority = <200>; + }; +}; + +&cpu { + cpu-supply = <&vcpu>; + operating-points = < + /* kHz uV */ + 1000000 1325000 + >; +}; + +&i2c0 { + status = "okay"; + + /* There are two regulators on the board. One is accessible via I2C, + * with buck1 providing SoC power (set up by bootloader to 1.325V or + * less depending on leakage value in OTP), and buck2 likely used for + * DRAM (providing 1.35V). The other regulator on the opposite side + * of the board is probably supplying SDIO and NAND fixed voltages. */ + regulator@19 { + compatible = "marvell,88pg868"; + reg = <0x19>; + + vcpu: buck1 { + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1325000>; + }; + }; +}; + +/* Fixed interface to on-board Marvell 8897 Wi-Fi/Bluetooth/NFC chip. */ +&sdhci0 { + keep-power-in-suspend; + non-removable; + status = "okay"; +}; + +&uart0 { + /* RX/TX are routed to TP50/TP51 on the board. */ + status = "okay"; +}; + +/* The SoC is connected to on-board USB hub that in turn has one downstream + * port wired to the on-board Steam Controller wireless receiver chip. */ +&usb_phy1 { status = "okay"; }; + +&usb1 { + dr_mode = "host"; + status = "okay"; +}; + +ð1 { status = "okay"; }; diff --git a/arch/arm/boot/dts/berlin2cd.dtsi b/arch/arm/boot/dts/berlin2cd.dtsi index 501c59d97eae..e5c1f4213ff9 100644 --- a/arch/arm/boot/dts/berlin2cd.dtsi +++ b/arch/arm/boot/dts/berlin2cd.dtsi @@ -1,3 +1,4 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) /* * Device Tree Include file for Marvell Armada 1500-mini (Berlin BG2CD) SoC * @@ -5,38 +6,6 @@ * * based on GPL'ed 2.6 kernel sources * (c) Marvell International Ltd. - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. */ #include <dt-bindings/clock/berlin2.h> @@ -57,7 +26,7 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu: cpu@0 { compatible = "arm,cortex-a9"; device_type = "cpu"; next-level-cache = <&l2>; @@ -73,6 +42,12 @@ }; }; + pmu { + compatible = "arm,cortex-a9-pmu"; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + }; + refclk: oscillator { compatible = "fixed-clock"; #clock-cells = <0>; @@ -87,11 +62,6 @@ ranges = <0 0xf7000000 0x1000000>; - pmu { - compatible = "arm,cortex-a9-pmu"; - interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; - }; - sdhci0: sdhci@ab0000 { compatible = "mrvl,pxav3-mmc"; reg = <0xab0000 0x200>; @@ -108,6 +78,11 @@ cache-level = <2>; }; + snoop-control-unit@ad0000 { + compatible = "arm,cortex-a9-scu"; + reg = <0xad0000 0x100>; + }; + gic: interrupt-controller@ad1000 { compatible = "arm,cortex-a9-gic"; reg = <0xad1000 0x1000>, <0xad0100 0x0100>; @@ -115,10 +90,24 @@ #interrupt-cells = <3>; }; + global-timer@ad0200 { + compatible = "arm,cortex-a9-global-timer"; + reg = <0xad0200 0x20>; + interrupts = <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>; + clocks = <&chip_clk CLKID_TWD>; + }; + local-timer@ad0600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0xad0600 0x20>; - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>; + clocks = <&chip_clk CLKID_TWD>; + }; + + local-wdt@ad0620 { + compatible = "arm,cortex-a9-twd-wdt"; + reg = <0xad0620 0x20>; + interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>; clocks = <&chip_clk CLKID_TWD>; }; @@ -254,6 +243,60 @@ }; }; + i2c0: i2c@1400 { + compatible = "snps,designware-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1400 0x100>; + interrupts = <16>; + clocks = <&chip_clk CLKID_CFG>; + status = "disabled"; + }; + + i2c1: i2c@1800 { + compatible = "snps,designware-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1800 0x100>; + interrupts = <17>; + clocks = <&chip_clk CLKID_CFG>; + status = "disabled"; + }; + + spi0: spi@1c00 { + compatible = "snps,dw-apb-ssi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1c00 0x100>; + interrupts = <4>; + clocks = <&chip_clk CLKID_CFG>; + status = "disabled"; + }; + + wdt4: watchdog@2000 { + compatible = "snps,dw-wdt"; + reg = <0x2000 0x100>; + clocks = <&chip_clk CLKID_CFG>; + interrupts = <5>; + status = "disabled"; + }; + + wdt5: watchdog@2400 { + compatible = "snps,dw-wdt"; + reg = <0x2400 0x100>; + clocks = <&chip_clk CLKID_CFG>; + interrupts = <6>; + status = "disabled"; + }; + + wdt6: watchdog@2800 { + compatible = "snps,dw-wdt"; + reg = <0x2800 0x100>; + clocks = <&chip_clk CLKID_CFG>; + interrupts = <7>; + status = "disabled"; + }; + timer0: timer@2c00 { compatible = "snps,dw-apb-timer"; reg = <0x2c00 0x14>; @@ -435,6 +478,36 @@ }; }; + spi1: spi@6000 { + compatible = "snps,dw-apb-ssi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6000 0x100>; + clocks = <&refclk>; + interrupts = <5>; + status = "disabled"; + }; + + i2c2: i2c@7000 { + compatible = "snps,designware-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x7000 0x100>; + interrupts = <6>; + clocks = <&refclk>; + status = "disabled"; + }; + + i2c3: i2c@8000 { + compatible = "snps,designware-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x8000 0x100>; + interrupts = <7>; + clocks = <&refclk>; + status = "disabled"; + }; + sm_gpio0: gpio@c000 { compatible = "snps,dw-apb-gpio"; reg = <0xc000 0x400>; @@ -472,6 +545,16 @@ status = "disabled"; }; + uart2: serial@b000 { + compatible = "snps,dw-apb-uart"; + reg = <0xb000 0x100>; + reg-shift = <2>; + reg-io-width = <1>; + interrupts = <10>; + clocks = <&refclk>; + status = "disabled"; + }; + sysctrl: system-controller@d000 { compatible = "simple-mfd", "syscon"; reg = <0xd000 0x100>; @@ -479,6 +562,12 @@ sys_pinctrl: pin-controller { compatible = "marvell,berlin2cd-system-pinctrl"; }; + + adc: adc { + compatible = "marvell,berlin2-adc"; + interrupts = <12>, <14>; + interrupt-names = "adc", "tsen"; + }; }; sic: interrupt-controller@e000 { diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts index 57aa5f8a7c77..c162f98cb8e8 100644 --- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts +++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts @@ -1,37 +1,6 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) /* * Copyright (C) 2014 Antoine Ténart <antoine.tenart@free-electrons.com> - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi index bf3a6c9a1d34..516a7ce25791 100644 --- a/arch/arm/boot/dts/berlin2q.dtsi +++ b/arch/arm/boot/dts/berlin2q.dtsi @@ -1,37 +1,6 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) /* * Copyright (C) 2014 Antoine Ténart <antoine.tenart@free-electrons.com> - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. */ #include <dt-bindings/clock/berlin2q.h> @@ -53,7 +22,7 @@ #size-cells = <0>; enable-method = "marvell,berlin-smp"; - cpu@0 { + cpu0: cpu@0 { compatible = "arm,cortex-a9"; device_type = "cpu"; next-level-cache = <&l2>; @@ -71,21 +40,21 @@ >; }; - cpu@1 { + cpu1: cpu@1 { compatible = "arm,cortex-a9"; device_type = "cpu"; next-level-cache = <&l2>; reg = <1>; }; - cpu@2 { + cpu2: cpu@2 { compatible = "arm,cortex-a9"; device_type = "cpu"; next-level-cache = <&l2>; reg = <2>; }; - cpu@3 { + cpu3: cpu@3 { compatible = "arm,cortex-a9"; device_type = "cpu"; next-level-cache = <&l2>; @@ -93,6 +62,19 @@ }; }; + pmu { + compatible = "arm,cortex-a9-pmu"; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, + <&cpu1>, + <&cpu2>, + <&cpu3>; + }; + refclk: oscillator { compatible = "fixed-clock"; #clock-cells = <0>; @@ -107,14 +89,6 @@ ranges = <0 0xf7000000 0x1000000>; interrupt-parent = <&gic>; - pmu { - compatible = "arm,cortex-a9-pmu"; - interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; - }; - sdhci0: sdhci@ab0000 { compatible = "mrvl,pxav3-mmc"; reg = <0xab0000 0x200>; @@ -145,6 +119,7 @@ l2: l2-cache-controller@ac0000 { compatible = "arm,pl310-cache"; reg = <0xac0000 0x1000>; + cache-unified; cache-level = <2>; arm,data-latency = <2 2 2>; arm,tag-latency = <2 2 2>; @@ -159,7 +134,7 @@ compatible = "arm,cortex-a9-twd-timer"; reg = <0xad0600 0x20>; clocks = <&chip_clk CLKID_TWD>; - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>; }; gic: interrupt-controller@ad1000 { diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts index 3962fa4b07f5..0e82bb988fde 100644 --- a/arch/arm/boot/dts/da850-evm.dts +++ b/arch/arm/boot/dts/da850-evm.dts @@ -27,143 +27,6 @@ spi0 = &spi1; }; - soc@1c00000 { - pmx_core: pinmux@14120 { - status = "okay"; - - mcasp0_pins: pinmux_mcasp0_pins { - pinctrl-single,bits = < - /* - * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR, - * AFSR, AMUTE - */ - 0x00 0x11111111 0xffffffff - /* AXR11, AXR12 */ - 0x04 0x00011000 0x000ff000 - >; - }; - nand_pins: nand_pins { - pinctrl-single,bits = < - /* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */ - 0x1c 0x10110110 0xf0ff0ff0 - /* - * EMA_D[0], EMA_D[1], EMA_D[2], - * EMA_D[3], EMA_D[4], EMA_D[5], - * EMA_D[6], EMA_D[7] - */ - 0x24 0x11111111 0xffffffff - /* EMA_A[1], EMA_A[2] */ - 0x30 0x01100000 0x0ff00000 - >; - }; - }; - serial0: serial@42000 { - status = "okay"; - }; - serial1: serial@10c000 { - status = "okay"; - }; - serial2: serial@10d000 { - status = "okay"; - }; - rtc0: rtc@23000 { - status = "okay"; - }; - i2c0: i2c@22000 { - status = "okay"; - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins>; - - tps: tps@48 { - reg = <0x48>; - }; - tlv320aic3106: tlv320aic3106@18 { - #sound-dai-cells = <0>; - compatible = "ti,tlv320aic3106"; - reg = <0x18>; - status = "okay"; - - /* Regulators */ - IOVDD-supply = <&vdcdc2_reg>; - /* Derived from VBAT: Baseboard 3.3V / 1.8V */ - AVDD-supply = <&vbat>; - DRVDD-supply = <&vbat>; - DVDD-supply = <&vbat>; - }; - tca6416: gpio@20 { - compatible = "ti,tca6416"; - reg = <0x20>; - gpio-controller; - #gpio-cells = <2>; - }; - }; - wdt: wdt@21000 { - status = "okay"; - }; - mmc0: mmc@40000 { - max-frequency = <50000000>; - bus-width = <4>; - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins>; - }; - spi1: spi@30e000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&spi1_pins &spi1_cs0_pin>; - flash: m25p80@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "m25p64"; - spi-max-frequency = <30000000>; - m25p,fast-read; - reg = <0>; - partition@0 { - label = "U-Boot-SPL"; - reg = <0x00000000 0x00010000>; - read-only; - }; - partition@1 { - label = "U-Boot"; - reg = <0x00010000 0x00080000>; - read-only; - }; - partition@2 { - label = "U-Boot-Env"; - reg = <0x00090000 0x00010000>; - read-only; - }; - partition@3 { - label = "Kernel"; - reg = <0x000a0000 0x00280000>; - }; - partition@4 { - label = "Filesystem"; - reg = <0x00320000 0x00400000>; - }; - partition@5 { - label = "MAC-Address"; - reg = <0x007f0000 0x00010000>; - read-only; - }; - }; - }; - mdio: mdio@224000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&mdio_pins>; - bus_freq = <2200000>; - }; - eth0: ethernet@220000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&mii_pins>; - }; - gpio: gpio@226000 { - status = "okay"; - }; - }; vbat: fixedregulator0 { compatible = "regulator-fixed"; regulator-name = "vbat"; @@ -200,6 +63,155 @@ }; }; +&pmx_core { + status = "okay"; + + mcasp0_pins: pinmux_mcasp0_pins { + pinctrl-single,bits = < + /* + * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR, + * AFSR, AMUTE + */ + 0x00 0x11111111 0xffffffff + /* AXR11, AXR12 */ + 0x04 0x00011000 0x000ff000 + >; + }; + nand_pins: nand_pins { + pinctrl-single,bits = < + /* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */ + 0x1c 0x10110110 0xf0ff0ff0 + /* + * EMA_D[0], EMA_D[1], EMA_D[2], + * EMA_D[3], EMA_D[4], EMA_D[5], + * EMA_D[6], EMA_D[7] + */ + 0x24 0x11111111 0xffffffff + /* EMA_A[1], EMA_A[2] */ + 0x30 0x01100000 0x0ff00000 + >; + }; +}; + +&serial0 { + status = "okay"; +}; + +&serial1 { + status = "okay"; +}; + +&serial2 { + status = "okay"; +}; + +&rtc0 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + tps: tps@48 { + reg = <0x48>; + }; + tlv320aic3106: tlv320aic3106@18 { + #sound-dai-cells = <0>; + compatible = "ti,tlv320aic3106"; + reg = <0x18>; + status = "okay"; + + /* Regulators */ + IOVDD-supply = <&vdcdc2_reg>; + /* Derived from VBAT: Baseboard 3.3V / 1.8V */ + AVDD-supply = <&vbat>; + DRVDD-supply = <&vbat>; + DVDD-supply = <&vbat>; + }; + tca6416: gpio@20 { + compatible = "ti,tca6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&wdt { + status = "okay"; +}; + +&mmc0 { + max-frequency = <50000000>; + bus-width = <4>; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + cd-gpios = <&gpio 64 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio 65 GPIO_ACTIVE_HIGH>; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins &spi1_cs0_pin>; + flash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p64"; + spi-max-frequency = <30000000>; + m25p,fast-read; + reg = <0>; + partition@0 { + label = "U-Boot-SPL"; + reg = <0x00000000 0x00010000>; + read-only; + }; + partition@1 { + label = "U-Boot"; + reg = <0x00010000 0x00080000>; + read-only; + }; + partition@2 { + label = "U-Boot-Env"; + reg = <0x00090000 0x00010000>; + read-only; + }; + partition@3 { + label = "Kernel"; + reg = <0x000a0000 0x00280000>; + }; + partition@4 { + label = "Filesystem"; + reg = <0x00320000 0x00400000>; + }; + partition@5 { + label = "MAC-Address"; + reg = <0x007f0000 0x00010000>; + read-only; + }; + }; +}; + +&mdio { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + bus_freq = <2200000>; +}; + +ð0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mii_pins>; +}; + +&gpio { + status = "okay"; +}; + /include/ "tps6507x.dtsi" &tps { @@ -309,6 +321,18 @@ }; }; +&usb_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; + &vpif { pinctrl-names = "default"; pinctrl-0 = <&vpif_capture_pins>, <&vpif_display_pins>; diff --git a/arch/arm/boot/dts/da850-lcdk.dts b/arch/arm/boot/dts/da850-lcdk.dts index a1f4d6d5a569..0edf769ea95c 100644 --- a/arch/arm/boot/dts/da850-lcdk.dts +++ b/arch/arm/boot/dts/da850-lcdk.dts @@ -21,8 +21,8 @@ stdout-path = "serial2:115200n8"; }; - memory { - device_type = "memory"; + memory@c0000000 { + /* 128 MB DDR2 SDRAM @ 0xc0000000 */ reg = <0xc0000000 0x08000000>; }; diff --git a/arch/arm/boot/dts/da850-lego-ev3.dts b/arch/arm/boot/dts/da850-lego-ev3.dts index 1ffd87796cac..ee3932475ce7 100644 --- a/arch/arm/boot/dts/da850-lego-ev3.dts +++ b/arch/arm/boot/dts/da850-lego-ev3.dts @@ -33,11 +33,9 @@ */ gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; label = "EV3 Brick Buttons"; pinctrl-names = "default"; - pinctrl-0 = <&button_pins>, <&button_bias>; + pinctrl-0 = <&button_bias>; center { label = "Center"; @@ -81,8 +79,6 @@ */ leds { compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins>; left_green { label = "led0:green:brick-status"; @@ -119,8 +115,6 @@ gpio-poweroff { compatible = "gpio-poweroff"; gpios = <&gpio 107 GPIO_ACTIVE_LOW>; - pinctrl-names = "default"; - pinctrl-0 = <&system_power_pin>; }; sound { @@ -136,8 +130,6 @@ * the sensor (input) ports, the motor (output) ports and the A/DC. */ vcc5v: regulator1 { - pinctrl-names = "default"; - pinctrl-0 = <&vcc5v_pins>; compatible = "regulator-fixed"; regulator-name = "vcc5v"; regulator-min-microvolt = <5000000>; @@ -165,8 +157,6 @@ * This is the amplifier for the speaker. */ amp: regulator3 { - pinctrl-names = "default"; - pinctrl-0 = <&_pins>; compatible = "regulator-fixed"; regulator-name = "amp"; gpio = <&gpio 111 GPIO_ACTIVE_HIGH>; @@ -177,8 +167,6 @@ * The EV3 can use 6-AA batteries or a rechargeable Li-ion battery pack. */ battery { - pinctrl-names = "default"; - pinctrl-0 = <&battery_pins>; compatible = "lego,ev3-battery"; io-channels = <&adc 4>, <&adc 3>; io-channel-names = "voltage", "current"; @@ -206,73 +194,10 @@ &pmx_core { status = "okay"; - mmc0_cd_pin: pinmux_mmc0_cd { - pinctrl-single,bits = < - /* GP5[14] */ - 0x2C 0x00000080 0x000000f0 - >; - }; - - button_pins: pinmux_button_pins { - pinctrl-single,bits = < - /* GP1[13] */ - 0x8 0x00000800 0x00000f00 - /* GP6[10] */ - 0x34 0x00800000 0x00f00000 - /* GP6[6] */ - 0x38 0x00000080 0x000000f0 - /* GP7[12], GP7[14], GP7[15] */ - 0x40 0x00808800 0x00f0ff00 - >; - }; - - led_pins: pinmux_led_pins { - pinctrl-single,bits = < - /* GP6[12], GP6[13], GP6[14] */ - 0x34 0x00008880 0x0000fff0 - /* GP6[7] */ - 0x38 0x00000008 0x0000000f - >; - }; - - system_power_pin: pinmux_system_power { - pinctrl-single,bits = < - /* GP6[11] */ - 0x34 0x00080000 0x000f0000 - >; - }; - - vcc5v_pins: pinmux_vcc5v { - pinctrl-single,bits = < - /* GP6[5] */ - 0x40 0x00000080 0x000000f0 - /* GP6[3] */ - 0x4c 0x00008000 0x0000f000 - >; - }; - - amp_pins: pinmux_amp_pins { - pinctrl-single,bits = < - /* GP6[15] */ - 0x34 0x00000008 0x0000000f - >; - }; - - battery_pins: pinmux_battery_pins { - pinctrl-single,bits = < - /* GP0[6] */ - 0x04 0x00000080 0x000000f0 - /* GP8[8] */ - 0x4c 0x00000080 0x000000f0 - >; - }; - ev3_lcd_pins: pinmux_lcd { pinctrl-single,bits = < - /* SIMO, GP2[11], GP2[12], CLK */ - 0x14 0x00188100 0x00ffff00 - /* GP5[0] */ - 0x30 0x80000000 0xf0000000 + /* SIMO, CLK */ + 0x14 0x00100100 0x00f00f00 >; }; }; @@ -327,7 +252,7 @@ bus-width = <4>; cd-gpios = <&gpio 94 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin>; + pinctrl-0 = <&mmc0_pins>; }; &spi0 { diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi index c66cf7895363..f6f1597b03df 100644 --- a/arch/arm/boot/dts/da850.dtsi +++ b/arch/arm/boot/dts/da850.dtsi @@ -7,10 +7,19 @@ * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. */ -#include "skeleton.dtsi" #include <dt-bindings/interrupt-controller/irq.h> / { + #address-cells = <1>; + #size-cells = <1>; + chosen { }; + aliases { }; + + memory@c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x0>; + }; + arm { #address-cells = <1>; #size-cells = <1>; @@ -46,14 +55,22 @@ pmx_core: pinmux@14120 { compatible = "pinctrl-single"; reg = <0x14120 0x50>; - #address-cells = <1>; - #size-cells = <0>; #pinctrl-cells = <2>; pinctrl-single,bit-per-mux; pinctrl-single,register-width = <32>; pinctrl-single,function-mask = <0xf>; + /* pin base, nr pins & gpio function */ + pinctrl-single,gpio-range = <&range 0 17 0x8>, + <&range 17 8 0x4>, + <&range 26 8 0x4>, + <&range 34 80 0x8>, + <&range 129 31 0x8>; status = "disabled"; + range: gpio-range { + #pinctrl-single,gpio-range-cells = <3>; + }; + serial0_rtscts_pins: pinmux_serial0_rtscts_pins { pinctrl-single,bits = < /* UART0_RTS UART0_CTS */ @@ -542,6 +559,150 @@ status = "disabled"; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&pmx_core 0 15 1>, + <&pmx_core 1 14 1>, + <&pmx_core 2 13 1>, + <&pmx_core 3 12 1>, + <&pmx_core 4 11 1>, + <&pmx_core 5 10 1>, + <&pmx_core 6 9 1>, + <&pmx_core 7 8 1>, + <&pmx_core 8 7 1>, + <&pmx_core 9 6 1>, + <&pmx_core 10 5 1>, + <&pmx_core 11 4 1>, + <&pmx_core 12 3 1>, + <&pmx_core 13 2 1>, + <&pmx_core 14 1 1>, + <&pmx_core 15 0 1>, + <&pmx_core 16 39 1>, + <&pmx_core 17 38 1>, + <&pmx_core 18 37 1>, + <&pmx_core 19 36 1>, + <&pmx_core 20 35 1>, + <&pmx_core 21 34 1>, + <&pmx_core 22 33 1>, + <&pmx_core 23 32 1>, + <&pmx_core 24 24 1>, + <&pmx_core 25 22 1>, + <&pmx_core 26 21 1>, + <&pmx_core 27 20 1>, + <&pmx_core 28 19 1>, + <&pmx_core 29 18 1>, + <&pmx_core 30 17 1>, + <&pmx_core 31 16 1>, + <&pmx_core 32 55 1>, + <&pmx_core 33 54 1>, + <&pmx_core 34 53 1>, + <&pmx_core 35 52 1>, + <&pmx_core 36 51 1>, + <&pmx_core 37 50 1>, + <&pmx_core 38 49 1>, + <&pmx_core 39 48 1>, + <&pmx_core 40 47 1>, + <&pmx_core 41 46 1>, + <&pmx_core 42 45 1>, + <&pmx_core 43 44 1>, + <&pmx_core 44 43 1>, + <&pmx_core 45 42 1>, + <&pmx_core 46 41 1>, + <&pmx_core 47 40 1>, + <&pmx_core 48 71 1>, + <&pmx_core 49 70 1>, + <&pmx_core 50 69 1>, + <&pmx_core 51 68 1>, + <&pmx_core 52 67 1>, + <&pmx_core 53 66 1>, + <&pmx_core 54 65 1>, + <&pmx_core 55 64 1>, + <&pmx_core 56 63 1>, + <&pmx_core 57 62 1>, + <&pmx_core 58 61 1>, + <&pmx_core 59 60 1>, + <&pmx_core 60 59 1>, + <&pmx_core 61 58 1>, + <&pmx_core 62 57 1>, + <&pmx_core 63 56 1>, + <&pmx_core 64 87 1>, + <&pmx_core 65 86 1>, + <&pmx_core 66 85 1>, + <&pmx_core 67 84 1>, + <&pmx_core 68 83 1>, + <&pmx_core 69 82 1>, + <&pmx_core 70 81 1>, + <&pmx_core 71 80 1>, + <&pmx_core 72 70 1>, + <&pmx_core 73 78 1>, + <&pmx_core 74 77 1>, + <&pmx_core 75 76 1>, + <&pmx_core 76 75 1>, + <&pmx_core 77 74 1>, + <&pmx_core 78 73 1>, + <&pmx_core 79 72 1>, + <&pmx_core 80 103 1>, + <&pmx_core 81 102 1>, + <&pmx_core 82 101 1>, + <&pmx_core 83 100 1>, + <&pmx_core 84 99 1>, + <&pmx_core 85 98 1>, + <&pmx_core 86 97 1>, + <&pmx_core 87 96 1>, + <&pmx_core 88 95 1>, + <&pmx_core 89 94 1>, + <&pmx_core 90 93 1>, + <&pmx_core 91 92 1>, + <&pmx_core 92 91 1>, + <&pmx_core 93 90 1>, + <&pmx_core 94 89 1>, + <&pmx_core 95 88 1>, + <&pmx_core 96 158 1>, + <&pmx_core 97 157 1>, + <&pmx_core 98 156 1>, + <&pmx_core 99 155 1>, + <&pmx_core 100 154 1>, + <&pmx_core 101 129 1>, + <&pmx_core 102 113 1>, + <&pmx_core 103 112 1>, + <&pmx_core 104 111 1>, + <&pmx_core 105 110 1>, + <&pmx_core 106 109 1>, + <&pmx_core 107 108 1>, + <&pmx_core 108 107 1>, + <&pmx_core 109 106 1>, + <&pmx_core 110 105 1>, + <&pmx_core 111 104 1>, + <&pmx_core 112 145 1>, + <&pmx_core 113 144 1>, + <&pmx_core 114 143 1>, + <&pmx_core 115 142 1>, + <&pmx_core 116 141 1>, + <&pmx_core 117 140 1>, + <&pmx_core 118 139 1>, + <&pmx_core 119 138 1>, + <&pmx_core 120 137 1>, + <&pmx_core 121 136 1>, + <&pmx_core 122 135 1>, + <&pmx_core 123 134 1>, + <&pmx_core 124 133 1>, + <&pmx_core 125 132 1>, + <&pmx_core 126 131 1>, + <&pmx_core 127 130 1>, + <&pmx_core 128 159 1>, + <&pmx_core 129 31 1>, + <&pmx_core 130 30 1>, + <&pmx_core 131 20 1>, + <&pmx_core 132 28 1>, + <&pmx_core 133 27 1>, + <&pmx_core 134 26 1>, + <&pmx_core 135 23 1>, + <&pmx_core 136 153 1>, + <&pmx_core 137 152 1>, + <&pmx_core 138 151 1>, + <&pmx_core 139 150 1>, + <&pmx_core 140 149 1>, + <&pmx_core 141 148 1>, + <&pmx_core 142 147 1>, + <&pmx_core 143 146 1>; }; pinconf: pin-controller@22c00c { compatible = "ti,da850-pupd"; diff --git a/arch/arm/boot/dts/dm8148-evm.dts b/arch/arm/boot/dts/dm8148-evm.dts index d6657b3bae84..85d7b5148b0a 100644 --- a/arch/arm/boot/dts/dm8148-evm.dts +++ b/arch/arm/boot/dts/dm8148-evm.dts @@ -10,7 +10,7 @@ / { model = "DM8148 EVM"; - compatible = "ti,dm8148-evm", "ti,dm8148"; + compatible = "ti,dm8148-evm", "ti,dm8148", "ti,dm814"; memory@80000000 { device_type = "memory"; diff --git a/arch/arm/boot/dts/dm8148-t410.dts b/arch/arm/boot/dts/dm8148-t410.dts index 63883b3479f9..c46a227b543d 100644 --- a/arch/arm/boot/dts/dm8148-t410.dts +++ b/arch/arm/boot/dts/dm8148-t410.dts @@ -9,7 +9,7 @@ / { model = "HP t410 Smart Zero Client"; - compatible = "hp,t410", "ti,dm8148"; + compatible = "hp,t410", "ti,dm8148", "ti,dm814"; memory@80000000 { device_type = "memory"; @@ -77,7 +77,7 @@ DM814X_IOPAD(0x09dc, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[0] */ DM814X_IOPAD(0x09e0, PIN_INPUT | 0x1) /* SD2_CLK */ DM814X_IOPAD(0x09f4, PIN_INPUT_PULLUP | 0x2) /* SD2_CMD */ - DM814X_IOPAD(0x0920, PIN_INPUT | 40) /* SD2_SDCD */ + DM814X_IOPAD(0x0920, PIN_INPUT | 0x40) /* SD2_SDCD */ >; }; diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts index c72a2132aa82..1d030d567307 100644 --- a/arch/arm/boot/dts/dm8168-evm.dts +++ b/arch/arm/boot/dts/dm8168-evm.dts @@ -10,7 +10,7 @@ / { model = "DM8168 EVM"; - compatible = "ti,dm8168-evm", "ti,dm8168"; + compatible = "ti,dm8168-evm", "ti,dm8168", "ti,dm816"; memory@80000000 { device_type = "memory"; diff --git a/arch/arm/boot/dts/dra62x-j5eco-evm.dts b/arch/arm/boot/dts/dra62x-j5eco-evm.dts index fee0547f7302..31b824ad5d29 100644 --- a/arch/arm/boot/dts/dra62x-j5eco-evm.dts +++ b/arch/arm/boot/dts/dra62x-j5eco-evm.dts @@ -10,7 +10,7 @@ / { model = "DRA62x J5 Eco EVM"; - compatible = "ti,dra62x-j5eco-evm", "ti,dra62x", "ti,dm8148"; + compatible = "ti,dra62x-j5eco-evm", "ti,dra62x", "ti,dm8148", "ti,dm814"; memory@80000000 { device_type = "memory"; diff --git a/arch/arm/boot/dts/dra7-evm-common.dtsi b/arch/arm/boot/dts/dra7-evm-common.dtsi index 05a7b1a01bc3..33230c8b2951 100644 --- a/arch/arm/boot/dts/dra7-evm-common.dtsi +++ b/arch/arm/boot/dts/dra7-evm-common.dtsi @@ -260,3 +260,18 @@ &pcie1_rc { status = "okay"; }; + +&mmc4 { + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + non-removable; + #address-cells = <1>; + #size-cells = <0>; + wifi@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio5>; + interrupts = <7 IRQ_TYPE_EDGE_RISING>; + }; +}; diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index f1425b0f3a54..0894593860d6 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -20,6 +20,16 @@ reg = <0x0 0x80000000 0x0 0x60000000>; /* 1536 MB */ }; + evm_12v0: fixedregulator-evm_12v0 { + /* main supply */ + compatible = "regulator-fixed"; + regulator-name = "evm_12v0"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + regulator-boot-on; + }; + evm_1v8_sw: fixedregulator-evm_1v8 { compatible = "regulator-fixed"; regulator-name = "evm_1v8"; @@ -54,6 +64,48 @@ regulator-max-microvolt = <1800000>; }; + evm_3v3: fixedregulator-evm3v3 { + /* Output of Cntlr A of TPS43351-Q1 on dra7-evm */ + compatible = "regulator-fixed"; + regulator-name = "evm_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&evm_12v0>; + regulator-always-on; + regulator-boot-on; + }; + + evm_5v0: fixedregulator-evm_5v0 { + /* Output of Cntlr B of TPS43351-Q1 on dra7-evm */ + compatible = "regulator-fixed"; + regulator-name = "evm_5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&evm_12v0>; + regulator-always-on; + regulator-boot-on; + }; + + evm_3v6: fixedregulator-evm_3v6 { + compatible = "regulator-fixed"; + regulator-name = "evm_3v6"; + regulator-min-microvolt = <3600000>; + regulator-max-microvolt = <3600000>; + vin-supply = <&evm_5v0>; + regulator-always-on; + regulator-boot-on; + }; + + vmmcwl_fixed: fixedregulator-mmcwl { + compatible = "regulator-fixed"; + regulator-name = "vmmcwl_fixed"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio5 8 0>; + startup-delay-us = <70000>; + enable-active-high; + }; + extcon_usb2: extcon_usb2 { compatible = "linux,extcon-usb-gpio"; id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>; @@ -325,6 +377,7 @@ vmmc-supply = <&evm_1v8_sw>; vqmmc-supply = <&evm_1v8_sw>; bus-width = <8>; + non-removable; pinctrl-names = "default", "hs", "ddr_1_8v-rev11", "ddr_1_8v", "hs200_1_8v-rev11", "hs200_1_8v"; pinctrl-0 = <&mmc2_pins_default>; pinctrl-1 = <&mmc2_pins_hs>; @@ -334,6 +387,21 @@ pinctrl-5 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>; }; +&mmc4 { + status = "okay"; + vmmc-supply = <&evm_3v6>; + vqmmc-supply = <&vmmcwl_fixed>; + pinctrl-names = "default-rev11", "default", "hs-rev11", "hs", "sdr12-rev11", "sdr12", "sdr25-rev11", "sdr25"; + pinctrl-0 = <&mmc4_pins_default &mmc4_iodelay_ds_rev11_conf>; + pinctrl-1 = <&mmc4_pins_default &mmc4_iodelay_ds_rev20_conf>; + pinctrl-2 = <&mmc4_pins_hs &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>; + pinctrl-3 = <&mmc4_pins_hs &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>; + pinctrl-4 = <&mmc4_pins_sdr12 &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>; + pinctrl-5 = <&mmc4_pins_sdr12 &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>; + pinctrl-6 = <&mmc4_pins_sdr25 &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>; + pinctrl-7 = <&mmc4_pins_sdr25 &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>; +}; + &cpu0 { vdd-supply = <&smps123_reg>; }; diff --git a/arch/arm/boot/dts/dra7-mmc-iodelay.dtsi b/arch/arm/boot/dts/dra7-mmc-iodelay.dtsi new file mode 100644 index 000000000000..aa0947266526 --- /dev/null +++ b/arch/arm/boot/dts/dra7-mmc-iodelay.dtsi @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * MMC IOdelay values for TI's DRA7xx SoCs. + * Copyright (C) 2018 Texas Instruments + * Author: Kishon Vijay Abraham I <kishon@ti.com> + */ + +&dra7_pmx_core { + mmc1_pins_default_no_clk_pu: mmc1_pins_default_no_clk_pu { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mmc1_clk.clk */ + DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ + DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ + DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ + DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ + DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ + >; + }; +}; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index f4ddd86f2c77..9dcd14edc202 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -1079,17 +1079,15 @@ }; mmc1: mmc@4809c000 { - compatible = "ti,omap4-hsmmc"; + compatible = "ti,dra7-sdhci"; reg = <0x4809c000 0x400>; interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc1"; - ti,dual-volt; - ti,needs-special-reset; - dmas = <&sdma_xbar 61>, <&sdma_xbar 62>; - dma-names = "tx", "rx"; status = "disabled"; pbias-supply = <&pbias_mmc_reg>; max-frequency = <192000000>; + mmc-ddr-1_8v; + mmc-ddr-3_3v; }; hdqw1w: 1w@480b2000 { @@ -1100,40 +1098,40 @@ }; mmc2: mmc@480b4000 { - compatible = "ti,omap4-hsmmc"; + compatible = "ti,dra7-sdhci"; reg = <0x480b4000 0x400>; interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc2"; - ti,needs-special-reset; - dmas = <&sdma_xbar 47>, <&sdma_xbar 48>; - dma-names = "tx", "rx"; status = "disabled"; max-frequency = <192000000>; + /* SDR104/DDR50/SDR50 bits in CAPA2 is not supported */ + sdhci-caps-mask = <0x7 0x0>; + mmc-hs200-1_8v; + mmc-ddr-1_8v; + mmc-ddr-3_3v; }; mmc3: mmc@480ad000 { - compatible = "ti,omap4-hsmmc"; + compatible = "ti,dra7-sdhci"; reg = <0x480ad000 0x400>; interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc3"; - ti,needs-special-reset; - dmas = <&sdma_xbar 77>, <&sdma_xbar 78>; - dma-names = "tx", "rx"; status = "disabled"; /* Errata i887 limits max-frequency of MMC3 to 64 MHz */ max-frequency = <64000000>; + /* SDMA is not supported */ + sdhci-caps-mask = <0x0 0x400000>; }; mmc4: mmc@480d1000 { - compatible = "ti,omap4-hsmmc"; + compatible = "ti,dra7-sdhci"; reg = <0x480d1000 0x400>; interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc4"; - ti,needs-special-reset; - dmas = <&sdma_xbar 57>, <&sdma_xbar 58>; - dma-names = "tx", "rx"; status = "disabled"; max-frequency = <192000000>; + /* SDMA is not supported */ + sdhci-caps-mask = <0x0 0x400000>; }; mmu0_dsp1: mmu@40d01000 { diff --git a/arch/arm/boot/dts/dra71-evm.dts b/arch/arm/boot/dts/dra71-evm.dts index ebc4bbae981e..b7aeaeeead3b 100644 --- a/arch/arm/boot/dts/dra71-evm.dts +++ b/arch/arm/boot/dts/dra71-evm.dts @@ -7,6 +7,7 @@ */ #include "dra72-evm-common.dtsi" +#include "dra7-mmc-iodelay.dtsi" #include "dra72x-mmc-iodelay.dtsi" #include <dt-bindings/net/ti-dp83867.h> @@ -50,19 +51,6 @@ }; }; -&dra7_pmx_core { - mmc1_pins_default: mmc1_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mmc1_clk.clk */ - DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ - DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ - DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ - DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ - DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ - >; - }; -}; - &i2c1 { status = "okay"; clock-frequency = <400000>; @@ -187,7 +175,7 @@ &mmc1 { pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; - pinctrl-0 = <&mmc1_pins_default>; + pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; pinctrl-1 = <&mmc1_pins_hs>; pinctrl-2 = <&mmc1_pins_sdr12>; pinctrl-3 = <&mmc1_pins_sdr25>; @@ -204,6 +192,7 @@ pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>; pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>; vmmc-supply = <&evm_1v8_sw>; + vqmmc-supply = <&evm_1v8_sw>; }; &mac { diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi index e85f560a2f78..df174f5c15d1 100644 --- a/arch/arm/boot/dts/dra72-evm-common.dtsi +++ b/arch/arm/boot/dts/dra72-evm-common.dtsi @@ -44,6 +44,16 @@ regulator-boot-on; }; + evm_3v6: fixedregulator-evm_3v6 { + compatible = "regulator-fixed"; + regulator-name = "evm_3v6"; + regulator-min-microvolt = <3600000>; + regulator-max-microvolt = <3600000>; + vin-supply = <&evm_5v0>; + regulator-always-on; + regulator-boot-on; + }; + vsys_3v3: fixedregulator-vsys3v3 { /* Output 2 of TPS43351QDAPRQ1 on dra72-evm */ /* Output 2 of LM5140QRWGTQ1 on dra71-evm */ @@ -171,36 +181,18 @@ clocks = <&atl_clkin2_ck>; }; }; -}; - -&dra7_pmx_core { - mmc1_pins_default: mmc1_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ - DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ - DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ - DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ - DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ - DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ - DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ - >; - }; - mmc2_pins_default: mmc2_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ - DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ - DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ - DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ - DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ - DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ - DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ - DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ - DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ - DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ - >; + vmmcwl_fixed: fixedregulator-mmcwl { + compatible = "regulator-fixed"; + regulator-name = "vmmcwl_fixed"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio5 8 GPIO_ACTIVE_HIGH>; + enable-active-high; }; +}; +&dra7_pmx_core { dcan1_pins_default: dcan1_pins_default { pinctrl-single,pins = < DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */ @@ -421,10 +413,33 @@ pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins_default>; bus-width = <8>; - ti,non-removable; + non-removable; max-frequency = <192000000>; }; +&mmc4 { + status = "okay"; + vmmc-supply = <&evm_3v6>; + vqmmc-supply = <&vmmcwl_fixed>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + non-removable; + pinctrl-names = "default", "hs", "sdr12", "sdr25"; + pinctrl-0 = <&mmc4_pins_default>; + pinctrl-1 = <&mmc4_pins_default>; + pinctrl-2 = <&mmc4_pins_default>; + pinctrl-3 = <&mmc4_pins_default>; + #address-cells = <1>; + #size-cells = <0>; + wifi@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio5>; + interrupts = <7 IRQ_TYPE_EDGE_RISING>; + }; +}; + &mac { status = "okay"; }; diff --git a/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi b/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi index 088013c6dc6e..edad87c4292c 100644 --- a/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi +++ b/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi @@ -202,6 +202,17 @@ DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ >; }; + + mmc4_pins_default: mmc4_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_ctsn.mmc4_clk */ + DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */ + DRA7XX_CORE_IOPAD(0x37f0, PIN_INPUT_PULLUP | MUX_MODE3) /* uart2_rxd.mmc4_dat0 */ + DRA7XX_CORE_IOPAD(0x37f4, PIN_INPUT_PULLUP | MUX_MODE3) /* uart2_txd.mmc4_dat1 */ + DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_PULLUP | MUX_MODE3) /* uart2_ctsn.mmc4_dat2 */ + DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_PULLUP | MUX_MODE3) /* uart2_rtsn.mmc4_dat3 */ + >; + }; }; &dra7_iodelay_core { diff --git a/arch/arm/boot/dts/dra76-evm.dts b/arch/arm/boot/dts/dra76-evm.dts index 2deb96405d06..c07f0051844d 100644 --- a/arch/arm/boot/dts/dra76-evm.dts +++ b/arch/arm/boot/dts/dra76-evm.dts @@ -42,6 +42,16 @@ regulator-boot-on; }; + vio_3v6: fixedregulator-vio_3v6 { + compatible = "regulator-fixed"; + regulator-name = "vio_3v6"; + regulator-min-microvolt = <3600000>; + regulator-max-microvolt = <3600000>; + vin-supply = <&vsys_5v0>; + regulator-always-on; + regulator-boot-on; + }; + vsys_3v3: fixedregulator-vsys3v3 { /* Output of Cntlr A of TPS43351-Q1 on dra76-evm */ compatible = "regulator-fixed"; @@ -81,6 +91,16 @@ vin-supply = <&smps5_reg>; }; + vmmcwl_fixed: fixedregulator-mmcwl { + compatible = "regulator-fixed"; + regulator-name = "vmmcwl_fixed"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio5 8 0>; /* gpio5_8 */ + startup-delay-us = <70000>; + enable-active-high; + }; + vtt_fixed: fixedregulator-vtt { compatible = "regulator-fixed"; regulator-name = "vtt_fixed"; @@ -307,7 +327,7 @@ &mmc1 { status = "okay"; vmmc-supply = <&vio_3v3_sd>; - vmmc_aux-supply = <&ldo4_reg>; + vqmmc-supply = <&ldo4_reg>; bus-width = <4>; /* * SDCD signal is not being used here - using the fact that GPIO mode @@ -324,6 +344,7 @@ vmmc-supply = <&vio_1v8>; vqmmc-supply = <&vio_1v8>; bus-width = <8>; + non-removable; pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v"; pinctrl-0 = <&mmc2_pins_default>; pinctrl-1 = <&mmc2_pins_default>; @@ -331,6 +352,17 @@ pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_conf>; }; +&mmc4 { + status = "okay"; + vmmc-supply = <&vio_3v6>; + vqmmc-supply = <&vmmcwl_fixed>; + pinctrl-names = "default", "hs", "sdr12", "sdr25"; + pinctrl-0 = <&mmc4_pins_hs &mmc4_iodelay_default_conf>; + pinctrl-1 = <&mmc4_pins_hs &mmc4_iodelay_manual1_conf>; + pinctrl-2 = <&mmc4_pins_hs &mmc4_iodelay_manual1_conf>; + pinctrl-3 = <&mmc4_pins_hs &mmc4_iodelay_manual1_conf>; +}; + /* No RTC on this device */ &rtc { status = "disabled"; diff --git a/arch/arm/boot/dts/emev2-kzm9d.dts b/arch/arm/boot/dts/emev2-kzm9d.dts index c238407133bf..0af44b7eadb9 100644 --- a/arch/arm/boot/dts/emev2-kzm9d.dts +++ b/arch/arm/boot/dts/emev2-kzm9d.dts @@ -34,9 +34,6 @@ gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - one { debounce-interval = <50>; wakeup-source; diff --git a/arch/arm/boot/dts/emev2.dtsi b/arch/arm/boot/dts/emev2.dtsi index 42ea246e71cb..fec1241b858f 100644 --- a/arch/arm/boot/dts/emev2.dtsi +++ b/arch/arm/boot/dts/emev2.dtsi @@ -31,13 +31,13 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu0: cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0>; clock-frequency = <533000000>; }; - cpu@1 { + cpu1: cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <1>; @@ -57,6 +57,7 @@ compatible = "arm,cortex-a9-pmu"; interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>; }; clocks@e0110000 { diff --git a/arch/arm/boot/dts/exynos-syscon-restart.dtsi b/arch/arm/boot/dts/exynos-syscon-restart.dtsi index 4b3dd0549a54..ecf416690a15 100644 --- a/arch/arm/boot/dts/exynos-syscon-restart.dtsi +++ b/arch/arm/boot/dts/exynos-syscon-restart.dtsi @@ -3,22 +3,18 @@ * Samsung's Exynos SoC syscon reboot/poweroff nodes common definition. */ -/ { - soc { - compatible = "simple-bus"; - - poweroff: syscon-poweroff { - compatible = "syscon-poweroff"; - regmap = <&pmu_system_controller>; - offset = <0x330C>; /* PS_HOLD_CONTROL */ - mask = <0x5200>; /* reset value */ - }; +&pmu_system_controller { + poweroff: syscon-poweroff { + compatible = "syscon-poweroff"; + regmap = <&pmu_system_controller>; + offset = <0x330C>; /* PS_HOLD_CONTROL */ + mask = <0x5200>; /* reset value */ + }; - reboot: syscon-reboot { - compatible = "syscon-reboot"; - regmap = <&pmu_system_controller>; - offset = <0x0400>; /* SWRESET */ - mask = <0x1>; - }; + reboot: syscon-reboot { + compatible = "syscon-reboot"; + regmap = <&pmu_system_controller>; + offset = <0x0400>; /* SWRESET */ + mask = <0x1>; }; }; diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts index 2c3460781cc6..2a6b828c01b7 100644 --- a/arch/arm/boot/dts/exynos3250-rinato.dts +++ b/arch/arm/boot/dts/exynos3250-rinato.dts @@ -24,6 +24,10 @@ i2c7 = &i2c_max77836; }; + chosen { + stdout-path = &serial_1; + }; + memory@40000000 { device_type = "memory"; reg = <0x40000000 0x1ff00000>; diff --git a/arch/arm/boot/dts/exynos3250.dtsi b/arch/arm/boot/dts/exynos3250.dtsi index 0a5f989d963b..962af97c1883 100644 --- a/arch/arm/boot/dts/exynos3250.dtsi +++ b/arch/arm/boot/dts/exynos3250.dtsi @@ -15,7 +15,6 @@ */ #include "exynos4-cpu-thermal.dtsi" -#include "exynos-syscon-restart.dtsi" #include <dt-bindings/clock/exynos3250.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/interrupt-controller/irq.h> @@ -919,3 +918,4 @@ }; #include "exynos3250-pinctrl.dtsi" +#include "exynos-syscon-restart.dtsi" diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi index 909a9f2bf5be..dfe41b698745 100644 --- a/arch/arm/boot/dts/exynos4.dtsi +++ b/arch/arm/boot/dts/exynos4.dtsi @@ -20,7 +20,6 @@ #include <dt-bindings/clock/exynos-audss-clk.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/interrupt-controller/irq.h> -#include "exynos-syscon-restart.dtsi" / { interrupt-parent = <&gic>; @@ -1025,3 +1024,5 @@ }; }; }; + +#include "exynos-syscon-restart.dtsi" diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts index 9a310e841d5d..2ab99f9f3d0a 100644 --- a/arch/arm/boot/dts/exynos4210-origen.dts +++ b/arch/arm/boot/dts/exynos4210-origen.dts @@ -34,26 +34,17 @@ stdout-path = &serial_2; }; - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - - mmc_reg: regulator@0 { - compatible = "regulator-fixed"; - reg = <0>; - regulator-name = "VMEM_VDD_2.8V"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; + mmc_reg: voltage-regulator { + compatible = "regulator-fixed"; + regulator-name = "VMEM_VDD_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>; + enable-active-high; }; gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; up { label = "Up"; @@ -131,12 +122,23 @@ cpu0-supply = <&buck1_reg>; }; +&exynos_usbphy { + status = "okay"; +}; + &fimd { pinctrl-0 = <&lcd_en &lcd_clk &lcd_data24 &pwm0_out>; pinctrl-names = "default"; status = "okay"; }; +&hsotg { + vusb_d-supply = <&ldo3_reg>; + vusb_a-supply = <&ldo8_reg>; + dr_mode = "peripheral"; + status = "okay"; +}; + &i2c_0 { status = "okay"; samsung,i2c-sda-delay = <100>; diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts index eaeeb4f6b84a..6f1d76cb7951 100644 --- a/arch/arm/boot/dts/exynos4210-trats.dts +++ b/arch/arm/boot/dts/exynos4210-trats.dts @@ -259,8 +259,8 @@ reg = <0x48>; interrupt-parent = <&gpx0>; interrupts = <4 IRQ_TYPE_EDGE_FALLING>; - x-size = <720>; - y-size = <1280>; + touchscreen-size-x = <720>; + touchscreen-size-y = <1280>; avdd-supply = <&tsp_reg>; vdd-supply = <&tsp_reg>; }; diff --git a/arch/arm/boot/dts/exynos4412-galaxy-s3.dtsi b/arch/arm/boot/dts/exynos4412-galaxy-s3.dtsi index ee8e1f445370..30eee5942eff 100644 --- a/arch/arm/boot/dts/exynos4412-galaxy-s3.dtsi +++ b/arch/arm/boot/dts/exynos4412-galaxy-s3.dtsi @@ -15,24 +15,22 @@ i2c10 = &i2c_cm36651; }; - regulators { - lcd_vdd3_reg: voltage-regulator-2 { - compatible = "regulator-fixed"; - regulator-name = "LCD_VDD_2.2V"; - regulator-min-microvolt = <2200000>; - regulator-max-microvolt = <2200000>; - gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; + lcd_vdd3_reg: voltage-regulator-6 { + compatible = "regulator-fixed"; + regulator-name = "LCD_VDD_2.2V"; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; - ps_als_reg: voltage-regulator-5 { - compatible = "regulator-fixed"; - regulator-name = "LED_A_3.0V"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - gpio = <&gpj0 5 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; + ps_als_reg: voltage-regulator-7 { + compatible = "regulator-fixed"; + regulator-name = "LED_A_3.0V"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + gpio = <&gpj0 5 GPIO_ACTIVE_HIGH>; + enable-active-high; }; i2c_ak8975: i2c-gpio-0 { @@ -120,8 +118,8 @@ reg = <0x48>; interrupt-parent = <&gpm2>; interrupts = <3 IRQ_TYPE_EDGE_FALLING>; - x-size = <720>; - y-size = <1280>; + touchscreen-size-x = <720>; + touchscreen-size-y = <1280>; avdd-supply = <&ldo23_reg>; vdd-supply = <&ldo24_reg>; }; diff --git a/arch/arm/boot/dts/exynos4412-midas.dtsi b/arch/arm/boot/dts/exynos4412-midas.dtsi index 76f2b30f1731..dc11ca1673e8 100644 --- a/arch/arm/boot/dts/exynos4412-midas.dtsi +++ b/arch/arm/boot/dts/exynos4412-midas.dtsi @@ -46,56 +46,50 @@ }; }; - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - - cam_io_reg: voltage-regulator-1 { - compatible = "regulator-fixed"; - regulator-name = "CAM_SENSOR_A"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - enable-active-high; - status = "disabled"; - }; + cam_io_reg: voltage-regulator-1 { + compatible = "regulator-fixed"; + regulator-name = "CAM_SENSOR_A"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + enable-active-high; + status = "disabled"; + }; - cam_af_reg: voltage-regulator-3 { - compatible = "regulator-fixed"; - regulator-name = "CAM_AF"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - enable-active-high; - status = "disabled"; - }; + cam_af_reg: voltage-regulator-2 { + compatible = "regulator-fixed"; + regulator-name = "CAM_AF"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + enable-active-high; + status = "disabled"; + }; - vsil12: voltage-regulator-6 { - compatible = "regulator-fixed"; - regulator-name = "VSIL_1.2V"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; - enable-active-high; - vin-supply = <&buck7_reg>; - }; + vsil12: voltage-regulator-3 { + compatible = "regulator-fixed"; + regulator-name = "VSIL_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&buck7_reg>; + }; - vcc33mhl: voltage-regulator-7 { - compatible = "regulator-fixed"; - regulator-name = "VCC_3.3_MHL"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; + vcc33mhl: voltage-regulator-4 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3.3_MHL"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; - vcc18mhl: voltage-regulator-8 { - compatible = "regulator-fixed"; - regulator-name = "VCC_1.8_MHL"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; + vcc18mhl: voltage-regulator-5 { + compatible = "regulator-fixed"; + regulator-name = "VCC_1.8_MHL"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; + enable-active-high; }; gpio-keys { diff --git a/arch/arm/boot/dts/exynos4412-n710x.dts b/arch/arm/boot/dts/exynos4412-n710x.dts index eb402a0d6651..fe2bfd76cc4e 100644 --- a/arch/arm/boot/dts/exynos4412-n710x.dts +++ b/arch/arm/boot/dts/exynos4412-n710x.dts @@ -13,15 +13,13 @@ /* bootargs are passed in by bootloader */ - regulators { - cam_vdda_reg: voltage-regulator-9 { - compatible = "regulator-fixed"; - regulator-name = "CAM_SENSOR_CORE_1.2V"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - gpio = <&gpm4 1 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; + cam_vdda_reg: voltage-regulator-6 { + compatible = "regulator-fixed"; + regulator-name = "CAM_SENSOR_CORE_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + gpio = <&gpm4 1 GPIO_ACTIVE_HIGH>; + enable-active-high; }; }; diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi index d7ad07fd48f9..a09e46c9dbc0 100644 --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi @@ -37,20 +37,14 @@ }; sound: sound { - compatible = "simple-audio-card"; + compatible = "hardkernel,odroid-xu4-audio"; - simple-audio-card,format = "i2s"; - simple-audio-card,bitclock-master = <&link0_codec>; - simple-audio-card,frame-master = <&link0_codec>; - - simple-audio-card,cpu { + cpu { sound-dai = <&i2s0 0>; - system-clock-frequency = <19200000>; }; - link0_codec: simple-audio-card,codec { - sound-dai = <&max98090>; - clocks = <&i2s0 CLK_I2S_CDCLK>; + codec { + sound-dai = <&hdmi>, <&max98090>; }; }; @@ -142,14 +136,25 @@ pinctrl-0 = <>; }; +&clock { + assigned-clocks = <&clock CLK_FOUT_EPLL>; + assigned-clock-rates = <45158401>; +}; + &clock_audss { assigned-clocks = <&clock_audss EXYNOS_MOUT_AUDSS>, <&clock_audss EXYNOS_MOUT_I2S>, <&clock_audss EXYNOS_DOUT_SRP>, - <&clock_audss EXYNOS_DOUT_AUD_BUS>; + <&clock_audss EXYNOS_DOUT_AUD_BUS>, + <&clock_audss EXYNOS_DOUT_I2S>; + assigned-clock-parents = <&clock CLK_FOUT_EPLL>, - <&clock_audss EXYNOS_MOUT_AUDSS>; - assigned-clock-rates = <0>, <0>, <192000000>, <19200000>; + <&clock_audss EXYNOS_MOUT_AUDSS>; + + assigned-clock-rates = <0>, <0>, + <196608001>, + <(196608001 / 2)>, + <(196608001 / 8)>; }; &cpu0 { @@ -498,6 +503,8 @@ pinctrl-0 = <&i2s0_bus>; pinctrl-names = "default"; status = "okay"; + assigned-clocks = <&i2s0 CLK_I2S_RCLK_SRC>; + assigned-clock-parents = <&clock_audss EXYNOS_SCLK_I2S>; }; &mixer { diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/exynos4412-odroidu3.dts index bdcd4523cc1c..459919b65df8 100644 --- a/arch/arm/boot/dts/exynos4412-odroidu3.dts +++ b/arch/arm/boot/dts/exynos4412-odroidu3.dts @@ -113,11 +113,11 @@ }; &sound { - simple-audio-card,name = "Odroid-U3"; - simple-audio-card,widgets = + model = "Odroid-U3"; + samsung,audio-widgets = "Headphone", "Headphone Jack", "Speakers", "Speakers"; - simple-audio-card,routing = + samsung,audio-routing = "Headphone Jack", "HPL", "Headphone Jack", "HPR", "Headphone Jack", "MICBIAS", diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts index 2dff129bc2ad..348556fcdd9d 100644 --- a/arch/arm/boot/dts/exynos4412-odroidx.dts +++ b/arch/arm/boot/dts/exynos4412-odroidx.dts @@ -97,12 +97,12 @@ }; &sound { - simple-audio-card,name = "Odroid-X"; - simple-audio-card,widgets = + model = "Odroid-X"; + samsung,audio-widgets = "Headphone", "Headphone Jack", "Microphone", "Mic Jack", "Microphone", "DMIC"; - simple-audio-card,routing = + samsung,audio-routing = "Headphone Jack", "HPL", "Headphone Jack", "HPR", "IN1", "Mic Jack", diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts index 1514f0dbaff8..346f71932457 100644 --- a/arch/arm/boot/dts/exynos4412-origen.dts +++ b/arch/arm/boot/dts/exynos4412-origen.dts @@ -90,7 +90,7 @@ samsung,vbus-gpio = <&gpx3 5 1>; status = "okay"; - port@1{ + port@1 { status = "okay"; }; port@2 { diff --git a/arch/arm/boot/dts/exynos4412.dtsi b/arch/arm/boot/dts/exynos4412.dtsi index 2ae1ab602f4b..7b43c10c510b 100644 --- a/arch/arm/boot/dts/exynos4412.dtsi +++ b/arch/arm/boot/dts/exynos4412.dtsi @@ -298,7 +298,7 @@ status = "disabled"; }; - sysmmu_g2d: sysmmu@10A40000{ + sysmmu_g2d: sysmmu@10a40000 { compatible = "samsung,exynos-sysmmu"; reg = <0x10A40000 0x1000>; interrupt-parent = <&combiner>; diff --git a/arch/arm/boot/dts/exynos5.dtsi b/arch/arm/boot/dts/exynos5.dtsi index f8d7de1144f1..5d2f0a06fbef 100644 --- a/arch/arm/boot/dts/exynos5.dtsi +++ b/arch/arm/boot/dts/exynos5.dtsi @@ -12,7 +12,6 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/interrupt-controller/irq.h> -#include "exynos-syscon-restart.dtsi" / { interrupt-parent = <&gic>; @@ -197,8 +196,6 @@ reg = <0x145B0000 0x1000>; interrupts = <10 3>; interrupt-parent = <&combiner>; - #address-cells = <1>; - #size-cells = <0>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi index 45283a6c5eee..2daf505b3d08 100644 --- a/arch/arm/boot/dts/exynos5250.dtsi +++ b/arch/arm/boot/dts/exynos5250.dtsi @@ -132,10 +132,6 @@ reg = <0x100440A0 0x20>; #power-domain-cells = <0>; label = "DISP1"; - clocks = <&clock CLK_FIN_PLL>, - <&clock CLK_MOUT_ACLK200_DISP1_SUB>, - <&clock CLK_MOUT_ACLK300_DISP1_SUB>; - clock-names = "oscclk", "clk0", "clk1"; }; pd_mau: power-domain@100440c0 { @@ -882,7 +878,7 @@ #iommu-cells = <0>; }; - sysmmu_fimc_dis1: sysmmu@132E0000{ + sysmmu_fimc_dis1: sysmmu@132e0000 { compatible = "samsung,exynos-sysmmu"; reg = <0x132E0000 0x1000>; interrupt-parent = <&combiner>; @@ -1117,3 +1113,4 @@ }; #include "exynos5250-pinctrl.dtsi" +#include "exynos-syscon-restart.dtsi" diff --git a/arch/arm/boot/dts/exynos5410.dtsi b/arch/arm/boot/dts/exynos5410.dtsi index 55509c690328..20e789ea136f 100644 --- a/arch/arm/boot/dts/exynos5410.dtsi +++ b/arch/arm/boot/dts/exynos5410.dtsi @@ -439,3 +439,4 @@ }; #include "exynos5410-pinctrl.dtsi" +#include "exynos-syscon-restart.dtsi" diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts index 244f0091c21f..57c2332bf282 100644 --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts @@ -29,7 +29,7 @@ aliases { /* Assign 20 so we don't get confused w/ builtin ones */ - i2c20 = "/spi@12d40000/cros-ec@0/i2c-tunnel"; + i2c20 = &i2c_tunnel; }; backlight: backlight { @@ -970,7 +970,7 @@ samsung,spi-feedback-delay = <1>; }; - i2c-tunnel { + i2c_tunnel: i2c-tunnel { compatible = "google,cros-ec-i2c-tunnel"; #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi index 2f3cb2a97f71..f4e8c5823bc2 100644 --- a/arch/arm/boot/dts/exynos5420.dtsi +++ b/arch/arm/boot/dts/exynos5420.dtsi @@ -276,10 +276,6 @@ reg = <0x10044000 0x20>; #power-domain-cells = <0>; label = "GSC"; - clocks = <&clock CLK_FIN_PLL>, - <&clock CLK_MOUT_USER_ACLK300_GSCL>, - <&clock CLK_GSCL0>, <&clock CLK_GSCL1>; - clock-names = "oscclk", "clk0", "asb0", "asb1"; }; isp_pd: power-domain@10044020 { @@ -292,10 +288,6 @@ mfc_pd: power-domain@10044060 { compatible = "samsung,exynos4210-pd"; reg = <0x10044060 0x20>; - clocks = <&clock CLK_FIN_PLL>, - <&clock CLK_MOUT_USER_ACLK333>, - <&clock CLK_ACLK333>; - clock-names = "oscclk", "clk0","asb0"; #power-domain-cells = <0>; label = "MFC"; }; @@ -312,12 +304,6 @@ reg = <0x100440C0 0x20>; #power-domain-cells = <0>; label = "DISP"; - clocks = <&clock CLK_FIN_PLL>, - <&clock CLK_MOUT_USER_ACLK200_DISP1>, - <&clock CLK_MOUT_USER_ACLK300_DISP1>, - <&clock CLK_MOUT_USER_ACLK400_DISP1>, - <&clock CLK_FIMD1>, <&clock CLK_MIXER>; - clock-names = "oscclk", "clk0", "clk1", "clk2", "asb0", "asb1"; }; mau_pd: power-domain@100440e0 { @@ -687,6 +673,36 @@ iommus = <&sysmmu_gscl1>; }; + scaler_0: scaler@12800000 { + compatible = "samsung,exynos5420-scaler"; + reg = <0x12800000 0x1294>; + interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clock CLK_MSCL0>; + clock-names = "mscl"; + power-domains = <&msc_pd>; + iommus = <&sysmmu_scaler0r>, <&sysmmu_scaler0w>; + }; + + scaler_1: scaler@12810000 { + compatible = "samsung,exynos5420-scaler"; + reg = <0x12810000 0x1294>; + interrupts = <0 221 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clock CLK_MSCL1>; + clock-names = "mscl"; + power-domains = <&msc_pd>; + iommus = <&sysmmu_scaler1r>, <&sysmmu_scaler1w>; + }; + + scaler_2: scaler@12820000 { + compatible = "samsung,exynos5420-scaler"; + reg = <0x12820000 0x1294>; + interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clock CLK_MSCL2>; + clock-names = "mscl"; + power-domains = <&msc_pd>; + iommus = <&sysmmu_scaler2r>, <&sysmmu_scaler2w>; + }; + jpeg_0: jpeg@11f50000 { compatible = "samsung,exynos5420-jpeg"; reg = <0x11F50000 0x1000>; @@ -761,7 +777,7 @@ #include "exynos5420-tmu-sensor-conf.dtsi" }; - sysmmu_g2dr: sysmmu@0x10A60000 { + sysmmu_g2dr: sysmmu@10a60000 { compatible = "samsung,exynos-sysmmu"; reg = <0x10A60000 0x1000>; interrupt-parent = <&combiner>; @@ -771,7 +787,7 @@ #iommu-cells = <0>; }; - sysmmu_g2dw: sysmmu@0x10A70000 { + sysmmu_g2dw: sysmmu@10a70000 { compatible = "samsung,exynos-sysmmu"; reg = <0x10A70000 0x1000>; interrupt-parent = <&combiner>; @@ -781,7 +797,7 @@ #iommu-cells = <0>; }; - sysmmu_tv: sysmmu@0x14650000 { + sysmmu_tv: sysmmu@14650000 { compatible = "samsung,exynos-sysmmu"; reg = <0x14650000 0x1000>; interrupt-parent = <&combiner>; @@ -792,7 +808,7 @@ #iommu-cells = <0>; }; - sysmmu_gscl0: sysmmu@0x13E80000 { + sysmmu_gscl0: sysmmu@13e80000 { compatible = "samsung,exynos-sysmmu"; reg = <0x13E80000 0x1000>; interrupt-parent = <&combiner>; @@ -803,7 +819,7 @@ #iommu-cells = <0>; }; - sysmmu_gscl1: sysmmu@0x13E90000 { + sysmmu_gscl1: sysmmu@13e90000 { compatible = "samsung,exynos-sysmmu"; reg = <0x13E90000 0x1000>; interrupt-parent = <&combiner>; @@ -814,65 +830,71 @@ #iommu-cells = <0>; }; - sysmmu_scaler0r: sysmmu@0x12880000 { + sysmmu_scaler0r: sysmmu@12880000 { compatible = "samsung,exynos-sysmmu"; reg = <0x12880000 0x1000>; interrupt-parent = <&combiner>; interrupts = <22 4>; clock-names = "sysmmu", "master"; clocks = <&clock CLK_SMMU_MSCL0>, <&clock CLK_MSCL0>; + power-domains = <&msc_pd>; #iommu-cells = <0>; }; - sysmmu_scaler1r: sysmmu@0x12890000 { + sysmmu_scaler1r: sysmmu@12890000 { compatible = "samsung,exynos-sysmmu"; reg = <0x12890000 0x1000>; interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>; clock-names = "sysmmu", "master"; clocks = <&clock CLK_SMMU_MSCL1>, <&clock CLK_MSCL1>; + power-domains = <&msc_pd>; #iommu-cells = <0>; }; - sysmmu_scaler2r: sysmmu@0x128A0000 { + sysmmu_scaler2r: sysmmu@128a0000 { compatible = "samsung,exynos-sysmmu"; reg = <0x128A0000 0x1000>; interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; clock-names = "sysmmu", "master"; clocks = <&clock CLK_SMMU_MSCL2>, <&clock CLK_MSCL2>; + power-domains = <&msc_pd>; #iommu-cells = <0>; }; - sysmmu_scaler0w: sysmmu@0x128C0000 { + sysmmu_scaler0w: sysmmu@128c0000 { compatible = "samsung,exynos-sysmmu"; reg = <0x128C0000 0x1000>; interrupt-parent = <&combiner>; interrupts = <27 2>; clock-names = "sysmmu", "master"; clocks = <&clock CLK_SMMU_MSCL0>, <&clock CLK_MSCL0>; + power-domains = <&msc_pd>; #iommu-cells = <0>; }; - sysmmu_scaler1w: sysmmu@0x128D0000 { + sysmmu_scaler1w: sysmmu@128d0000 { compatible = "samsung,exynos-sysmmu"; reg = <0x128D0000 0x1000>; interrupt-parent = <&combiner>; interrupts = <22 6>; clock-names = "sysmmu", "master"; clocks = <&clock CLK_SMMU_MSCL1>, <&clock CLK_MSCL1>; + power-domains = <&msc_pd>; #iommu-cells = <0>; }; - sysmmu_scaler2w: sysmmu@0x128E0000 { + sysmmu_scaler2w: sysmmu@128e0000 { compatible = "samsung,exynos-sysmmu"; reg = <0x128E0000 0x1000>; interrupt-parent = <&combiner>; interrupts = <19 6>; clock-names = "sysmmu", "master"; clocks = <&clock CLK_SMMU_MSCL2>, <&clock CLK_MSCL2>; + power-domains = <&msc_pd>; #iommu-cells = <0>; }; - sysmmu_rotator: sysmmu@0x11D40000 { + sysmmu_rotator: sysmmu@11d40000 { compatible = "samsung,exynos-sysmmu"; reg = <0x11D40000 0x1000>; interrupt-parent = <&combiner>; @@ -882,7 +904,7 @@ #iommu-cells = <0>; }; - sysmmu_jpeg0: sysmmu@0x11F10000 { + sysmmu_jpeg0: sysmmu@11f10000 { compatible = "samsung,exynos-sysmmu"; reg = <0x11F10000 0x1000>; interrupt-parent = <&combiner>; @@ -892,7 +914,7 @@ #iommu-cells = <0>; }; - sysmmu_jpeg1: sysmmu@0x11F20000 { + sysmmu_jpeg1: sysmmu@11f20000 { compatible = "samsung,exynos-sysmmu"; reg = <0x11F20000 0x1000>; interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; @@ -901,7 +923,7 @@ #iommu-cells = <0>; }; - sysmmu_mfc_l: sysmmu@0x11200000 { + sysmmu_mfc_l: sysmmu@11200000 { compatible = "samsung,exynos-sysmmu"; reg = <0x11200000 0x1000>; interrupt-parent = <&combiner>; @@ -912,7 +934,7 @@ #iommu-cells = <0>; }; - sysmmu_mfc_r: sysmmu@0x11210000 { + sysmmu_mfc_r: sysmmu@11210000 { compatible = "samsung,exynos-sysmmu"; reg = <0x11210000 0x1000>; interrupt-parent = <&combiner>; @@ -923,7 +945,7 @@ #iommu-cells = <0>; }; - sysmmu_fimd1_0: sysmmu@0x14640000 { + sysmmu_fimd1_0: sysmmu@14640000 { compatible = "samsung,exynos-sysmmu"; reg = <0x14640000 0x1000>; interrupt-parent = <&combiner>; @@ -934,7 +956,7 @@ #iommu-cells = <0>; }; - sysmmu_fimd1_1: sysmmu@0x14680000 { + sysmmu_fimd1_1: sysmmu@14680000 { compatible = "samsung,exynos-sysmmu"; reg = <0x14680000 0x1000>; interrupt-parent = <&combiner>; @@ -1531,3 +1553,4 @@ }; #include "exynos5420-pinctrl.dtsi" +#include "exynos-syscon-restart.dtsi" diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi index d31249f25ccf..2f4f40882dab 100644 --- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi @@ -23,7 +23,7 @@ stdout-path = "serial2:115200n8"; }; - firmware@02073000 { + firmware@2073000 { compatible = "samsung,secure-firmware"; reg = <0x02073000 0x1000>; }; diff --git a/arch/arm/boot/dts/exynos5440-sd5v1.dts b/arch/arm/boot/dts/exynos5440-sd5v1.dts deleted file mode 100644 index c4b8392d1ae1..000000000000 --- a/arch/arm/boot/dts/exynos5440-sd5v1.dts +++ /dev/null @@ -1,42 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * SAMSUNG SD5v1 board device tree source - * - * Copyright (c) 2013 Samsung Electronics Co., Ltd. - * http://www.samsung.com - */ - -/dts-v1/; -#include "exynos5440.dtsi" - -/ { - model = "SAMSUNG SD5v1 board based on EXYNOS5440"; - compatible = "samsung,sd5v1", "samsung,exynos5440", "samsung,exynos5"; - - chosen { - bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel earlyprintk no_console_suspend mem=2048M@0x80000000 mem=6144M@0x100000000 console=ttySAC0,115200"; - }; - - /* FIXME: set reg property with correct start address and size */ - memory@0 { - device_type = "memory"; - reg = <0 0>; - }; - - fixed-rate-clocks { - xtal { - compatible = "samsung,clock-xtal"; - clock-frequency = <50000000>; - }; - }; - - spi { - status = "disabled"; - }; - -}; - -&gmac { - fixed_phy; - phy_addr = <1>; -}; diff --git a/arch/arm/boot/dts/exynos5440-ssdk5440.dts b/arch/arm/boot/dts/exynos5440-ssdk5440.dts deleted file mode 100644 index a33c4fc29ae5..000000000000 --- a/arch/arm/boot/dts/exynos5440-ssdk5440.dts +++ /dev/null @@ -1,81 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * SAMSUNG SSDK5440 board device tree source - * - * Copyright (c) 2012 Samsung Electronics Co., Ltd. - * http://www.samsung.com - */ - -/dts-v1/; -#include "exynos5440.dtsi" -#include <dt-bindings/gpio/gpio.h> - -/ { - model = "SAMSUNG SSDK5440 board based on EXYNOS5440"; - compatible = "samsung,ssdk5440", "samsung,exynos5440", "samsung,exynos5"; - - chosen { - bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel earlyprintk no_console_suspend mem=2048M@0x80000000 mem=6144M@0x100000000 console=ttySAC0,115200"; - }; - - /* FIXME: set reg property with correct start address and size */ - memory@0 { - device_type = "memory"; - reg = <0 0>; - }; - - fixed-rate-clocks { - xtal { - compatible = "samsung,clock-xtal"; - clock-frequency = <50000000>; - }; - }; -}; - -&pcie_0 { - reset-gpio = <&pin_ctrl 5 GPIO_ACTIVE_HIGH>; - status = "okay"; -}; - -&pcie_1 { - reset-gpio = <&pin_ctrl 22 GPIO_ACTIVE_HIGH>; - status = "okay"; -}; - -&spi_0 { - flash: w25q128@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "winbond,w25q128"; - spi-max-frequency = <15625000>; - reg = <0>; - controller-data { - samsung,spi-feedback-delay = <0>; - }; - - partition@0 { - label = "BootLoader"; - reg = <0x60000 0x80000>; - read-only; - }; - - partition@e0000 { - label = "Recovery-Kernel"; - reg = <0xe0000 0x300000>; - read-only; - }; - - partition@3e0000 { - label = "CRAM-FS"; - reg = <0x3e0000 0x700000>; - read-only; - }; - - partition@ae0000 { - label = "User-Data"; - reg = <0xae0000 0x520000>; - }; - - }; - -}; diff --git a/arch/arm/boot/dts/exynos5440-tmu-sensor-conf.dtsi b/arch/arm/boot/dts/exynos5440-tmu-sensor-conf.dtsi deleted file mode 100644 index 0421c3d42905..000000000000 --- a/arch/arm/boot/dts/exynos5440-tmu-sensor-conf.dtsi +++ /dev/null @@ -1,20 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Device tree sources for Exynos5440 TMU sensor configuration - * - * Copyright (c) 2014 Lukasz Majewski <l.majewski@samsung.com> - */ - -#include <dt-bindings/thermal/thermal_exynos.h> - -#thermal-sensor-cells = <0>; -samsung,tmu_gain = <5>; -samsung,tmu_reference_voltage = <16>; -samsung,tmu_noise_cancel_mode = <4>; -samsung,tmu_efuse_value = <0x5d2d>; -samsung,tmu_min_efuse_value = <16>; -samsung,tmu_max_efuse_value = <76>; -samsung,tmu_first_point_trim = <25>; -samsung,tmu_second_point_trim = <70>; -samsung,tmu_default_temp_offset = <25>; -samsung,tmu_cal_type = <TYPE_ONE_POINT_TRIMMING>; diff --git a/arch/arm/boot/dts/exynos5440-trip-points.dtsi b/arch/arm/boot/dts/exynos5440-trip-points.dtsi deleted file mode 100644 index a2b04fed7d0b..000000000000 --- a/arch/arm/boot/dts/exynos5440-trip-points.dtsi +++ /dev/null @@ -1,21 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Device tree sources for default Exynos5440 thermal zone definition - * - * Copyright (c) 2014 Lukasz Majewski <l.majewski@samsung.com> - */ - -polling-delay-passive = <0>; -polling-delay = <0>; -trips { - cpu-alert-0 { - temperature = <100000>; /* millicelsius */ - hysteresis = <0>; /* millicelsius */ - type = "active"; - }; - cpu-crit-0 { - temperature = <105000>; /* millicelsius */ - hysteresis = <0>; /* millicelsius */ - type = "critical"; - }; -}; diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi deleted file mode 100644 index f3abecc44657..000000000000 --- a/arch/arm/boot/dts/exynos5440.dtsi +++ /dev/null @@ -1,355 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * SAMSUNG EXYNOS5440 SoC device tree source - * - * Copyright (c) 2012 Samsung Electronics Co., Ltd. - * http://www.samsung.com - */ - -#include <dt-bindings/clock/exynos5440.h> -#include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/interrupt-controller/irq.h> - -/ { - compatible = "samsung,exynos5440", "samsung,exynos5"; - - interrupt-parent = <&gic>; - #address-cells = <1>; - #size-cells = <1>; - - aliases { - serial0 = &serial_0; - serial1 = &serial_1; - spi0 = &spi_0; - tmuctrl0 = &tmuctrl_0; - tmuctrl1 = &tmuctrl_1; - tmuctrl2 = &tmuctrl_2; - }; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a15"; - reg = <0>; - }; - cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a15"; - reg = <1>; - }; - cpu@2 { - device_type = "cpu"; - compatible = "arm,cortex-a15"; - reg = <2>; - }; - cpu@3 { - device_type = "cpu"; - compatible = "arm,cortex-a15"; - reg = <3>; - }; - }; - - soc: soc { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - clock: clock-controller@160000 { - compatible = "samsung,exynos5440-clock"; - reg = <0x160000 0x1000>; - #clock-cells = <1>; - }; - - gic: interrupt-controller@2e0000 { - compatible = "arm,cortex-a15-gic"; - #interrupt-cells = <3>; - interrupt-controller; - reg = <0x2E1000 0x1000>, - <0x2E2000 0x2000>, - <0x2E4000 0x2000>, - <0x2E6000 0x2000>; - interrupts = <GIC_PPI 9 - (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; - }; - - - arm-pmu { - compatible = "arm,cortex-a15-pmu", "arm,cortex-a9-pmu"; - interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; - }; - - timer { - compatible = "arm,cortex-a15-timer", - "arm,armv7-timer"; - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; - clock-frequency = <50000000>; - }; - - cpufreq@160000 { - compatible = "samsung,exynos5440-cpufreq"; - reg = <0x160000 0x1000>; - interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; - operating-points = < - /* KHz uV */ - 1500000 1100000 - 1400000 1075000 - 1300000 1050000 - 1200000 1025000 - 1100000 1000000 - 1000000 975000 - 900000 950000 - 800000 925000 - >; - }; - - serial_0: serial@b0000 { - compatible = "samsung,exynos4210-uart"; - reg = <0xB0000 0x1000>; - interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clock CLK_B_125>, <&clock CLK_B_125>; - clock-names = "uart", "clk_uart_baud0"; - }; - - serial_1: serial@c0000 { - compatible = "samsung,exynos4210-uart"; - reg = <0xC0000 0x1000>; - interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clock CLK_B_125>, <&clock CLK_B_125>; - clock-names = "uart", "clk_uart_baud0"; - }; - - spi_0: spi@d0000 { - compatible = "samsung,exynos5440-spi"; - reg = <0xD0000 0x100>; - interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - samsung,spi-src-clk = <0>; - num-cs = <1>; - clocks = <&clock CLK_B_125>, <&clock CLK_SPI_BAUD>; - clock-names = "spi", "spi_busclk0"; - }; - - pin_ctrl: pinctrl@e0000 { - compatible = "samsung,exynos5440-pinctrl"; - reg = <0xE0000 0x1000>; - interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; - interrupt-controller; - #interrupt-cells = <2>; - #gpio-cells = <2>; - - fan: fan { - samsung,exynos5440-pin-function = <1>; - }; - - hdd_led0: hdd_led0 { - samsung,exynos5440-pin-function = <2>; - }; - - hdd_led1: hdd_led1 { - samsung,exynos5440-pin-function = <3>; - }; - - uart1: uart1 { - samsung,exynos5440-pin-function = <4>; - }; - }; - - i2c@f0000 { - compatible = "samsung,exynos5440-i2c"; - reg = <0xF0000 0x1000>; - interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&clock CLK_B_125>; - clock-names = "i2c"; - }; - - i2c@100000 { - compatible = "samsung,exynos5440-i2c"; - reg = <0x100000 0x1000>; - interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&clock CLK_B_125>; - clock-names = "i2c"; - }; - - watchdog@110000 { - compatible = "samsung,s3c6410-wdt"; - reg = <0x110000 0x1000>; - interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clock CLK_B_125>; - clock-names = "watchdog"; - }; - - gmac: ethernet@230000 { - compatible = "snps,dwmac-3.70a", "snps,dwmac"; - reg = <0x00230000 0x8000>; - interrupt-parent = <&gic>; - interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "macirq"; - phy-mode = "sgmii"; - clocks = <&clock CLK_GMAC0>; - clock-names = "stmmaceth"; - }; - - amba { - #address-cells = <1>; - #size-cells = <1>; - compatible = "simple-bus"; - interrupt-parent = <&gic>; - ranges; - }; - - rtc@130000 { - compatible = "samsung,s3c6410-rtc"; - reg = <0x130000 0x1000>; - interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clock CLK_B_125>; - clock-names = "rtc"; - }; - - tmuctrl_0: tmuctrl@160118 { - compatible = "samsung,exynos5440-tmu"; - reg = <0x160118 0x230>, <0x160368 0x10>; - interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clock CLK_B_125>; - clock-names = "tmu_apbif"; - #include "exynos5440-tmu-sensor-conf.dtsi" - }; - - tmuctrl_1: tmuctrl@16011c { - compatible = "samsung,exynos5440-tmu"; - reg = <0x16011C 0x230>, <0x160368 0x10>; - interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clock CLK_B_125>; - clock-names = "tmu_apbif"; - #include "exynos5440-tmu-sensor-conf.dtsi" - }; - - tmuctrl_2: tmuctrl@160120 { - compatible = "samsung,exynos5440-tmu"; - reg = <0x160120 0x230>, <0x160368 0x10>; - interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clock CLK_B_125>; - clock-names = "tmu_apbif"; - #include "exynos5440-tmu-sensor-conf.dtsi" - }; - - sata@210000 { - compatible = "snps,exynos5440-ahci"; - reg = <0x210000 0x10000>; - interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clock CLK_SATA>; - clock-names = "sata"; - }; - - ohci@220000 { - compatible = "samsung,exynos5440-ohci"; - reg = <0x220000 0x1000>; - interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clock CLK_USB>; - clock-names = "usbhost"; - }; - - ehci@221000 { - compatible = "samsung,exynos5440-ehci"; - reg = <0x221000 0x1000>; - interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clock CLK_USB>; - clock-names = "usbhost"; - }; - - pcie_phy0: pcie-phy@270000 { - #phy-cells = <0>; - compatible = "samsung,exynos5440-pcie-phy"; - reg = <0x270000 0x1000>, <0x271000 0x40>; - }; - - pcie_phy1: pcie-phy@272000 { - #phy-cells = <0>; - compatible = "samsung,exynos5440-pcie-phy"; - reg = <0x272000 0x1000>, <0x271040 0x40>; - }; - - pcie_0: pcie@290000 { - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; - reg = <0x290000 0x1000>, <0x40000000 0x1000>; - reg-names = "elbi", "config"; - interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clock CLK_PR0_250_O>, <&clock CLK_PB0_250_O>; - clock-names = "pcie", "pcie_bus"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - phys = <&pcie_phy0>; - ranges = <0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */ - bus-range = <0x00 0xff>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0x0 0 &gic 53>; - num-lanes = <4>; - status = "disabled"; - }; - - pcie_1: pcie@2a0000 { - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; - reg = <0x2a0000 0x1000>, <0x60000000 0x1000>; - reg-names = "elbi", "config"; - interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clock CLK_PR1_250_O>, <&clock CLK_PB0_250_O>; - clock-names = "pcie", "pcie_bus"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - phys = <&pcie_phy1>; - ranges = <0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */ - bus-range = <0x00 0xff>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0x0 0 &gic 56>; - num-lanes = <4>; - status = "disabled"; - }; - }; - - thermal-zones { - cpu0_thermal: cpu0-thermal { - thermal-sensors = <&tmuctrl_0>; - #include "exynos5440-trip-points.dtsi" - }; - cpu1_thermal: cpu1-thermal { - thermal-sensors = <&tmuctrl_1>; - #include "exynos5440-trip-points.dtsi" - }; - cpu2_thermal: cpu2-thermal { - thermal-sensors = <&tmuctrl_2>; - #include "exynos5440-trip-points.dtsi" - }; - }; -}; diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts index 2f8df9244f72..d80ab9085da1 100644 --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts @@ -27,7 +27,7 @@ aliases { /* Assign 20 so we don't get confused w/ builtin ones */ - i2c20 = "/spi@12d40000/cros-ec@0/i2c-tunnel"; + i2c20 = &i2c_tunnel; }; backlight: backlight { @@ -939,7 +939,7 @@ samsung,spi-feedback-delay = <1>; }; - i2c-tunnel { + i2c_tunnel: i2c-tunnel { compatible = "google,cros-ec-i2c-tunnel"; #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/gemini-dlink-dir-685.dts b/arch/arm/boot/dts/gemini-dlink-dir-685.dts index cadde92bc6b5..fb5c954ab95a 100644 --- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts +++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts @@ -13,22 +13,22 @@ #address-cells = <1>; #size-cells = <1>; - memory { + memory@0 { /* 128 MB SDRAM in 2 x Hynix HY5DU121622DTP-D43 */ device_type = "memory"; reg = <0x00000000 0x8000000>; }; chosen { - stdout-path = "uart0:115200n8"; + bootargs = "console=ttyS0,19200n8 root=/dev/sda1 rw rootwait"; + stdout-path = "uart0:19200n8"; }; gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; + button-esc { - debounce_interval = <50>; + debounce-interval = <50>; wakeup-source; linux,code = <KEY_ESC>; label = "reset"; @@ -36,7 +36,7 @@ gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; }; button-eject { - debounce_interval = <50>; + debounce-interval = <50>; wakeup-source; linux,code = <KEY_EJECTCD>; label = "unmount"; @@ -98,7 +98,7 @@ /* * These two LEDs are on the side of the device. * For electrical reasons, both LEDs cannot be active - * at the same time so only blue or orange can on at + * at the same time so only blue or orange can be on at * one time. Enabling both makes the LED go dark. * The LEDs both sit inside the unmount button and the * label on the case says "unmount". @@ -108,12 +108,14 @@ /* Collides with LPC_SERIRQ, UART DTR, SSP FSC pins */ gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; default-state = "off"; + linux,default-trigger = "disk-read"; }; led-orange-hd { label = "dir685:orange:HD"; /* Collides with LPC_LAD[2], UART DSR, SSP ECLK pins */ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; default-state = "off"; + linux,default-trigger = "disk-write"; }; }; diff --git a/arch/arm/boot/dts/gemini-dlink-dns-313.dts b/arch/arm/boot/dts/gemini-dlink-dns-313.dts index 403364a7aab9..d1329322b968 100644 --- a/arch/arm/boot/dts/gemini-dlink-dns-313.dts +++ b/arch/arm/boot/dts/gemini-dlink-dns-313.dts @@ -15,7 +15,7 @@ #address-cells = <1>; #size-cells = <1>; - memory { + memory@0 { /* 64 MB SDRAM in a Nanya NT5DS32M16BS-6K package */ device_type = "memory"; reg = <0x00000000 0x4000000>; @@ -26,15 +26,15 @@ }; chosen { + bootargs = "console=ttyS0,19200n8 root=/dev/sda4 rw rootwait"; stdout-path = "uart0:19200n8"; }; gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; + button-esc { - debounce_interval = <50>; + debounce-interval = <50>; wakeup-source; linux,code = <KEY_ESC>; label = "reset"; @@ -59,14 +59,13 @@ label = "dns313:green:disk"; gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>; default-state = "off"; - linux,default-trigger = "ide-disk"; - /* Ideally should activate while reading */ + linux,default-trigger = "disk-read"; }; led-disk-red { label = "dns313:red:disk"; gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; default-state = "off"; - /* Ideally should activate while writing */ + linux,default-trigger = "disk-write"; }; }; @@ -158,8 +157,12 @@ soc { flash@30000000 { + /* + * This is a Eon EN29LV400AB 512 KiB flash with + * three partitions. + */ + compatible = "cortina,gemini-flash", "jedec-flash"; status = "okay"; - /* 512KB of flash */ reg = <0x30000000 0x00080000>; /* diff --git a/arch/arm/boot/dts/gemini-nas4220b.dts b/arch/arm/boot/dts/gemini-nas4220b.dts index 4785fbcc41ed..963ea890c87f 100644 --- a/arch/arm/boot/dts/gemini-nas4220b.dts +++ b/arch/arm/boot/dts/gemini-nas4220b.dts @@ -14,7 +14,7 @@ #address-cells = <1>; #size-cells = <1>; - memory { /* 128 MB */ + memory@0 { /* 128 MB */ device_type = "memory"; reg = <0x00000000 0x8000000>; }; @@ -26,19 +26,17 @@ gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - button@29 { - debounce_interval = <50>; + button-setup { + debounce-interval = <50>; wakeup-source; linux,code = <KEY_SETUP>; label = "Backup button"; /* Conflict with TVC */ gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; }; - button@31 { - debounce_interval = <50>; + button-restart { + debounce-interval = <50>; wakeup-source; linux,code = <KEY_RESTART>; label = "Softreset button"; @@ -49,13 +47,13 @@ leds { compatible = "gpio-leds"; - led@28 { + led-orange-hdd { label = "nas4220b:orange:hdd"; /* Conflict with TVC */ gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - led@30 { + led-green-os { label = "nas4220b:green:os"; /* Conflict with TVC */ gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>; @@ -202,5 +200,9 @@ ata@63000000 { status = "okay"; }; + + ata@63400000 { + status = "okay"; + }; }; }; diff --git a/arch/arm/boot/dts/gemini-rut1xx.dts b/arch/arm/boot/dts/gemini-rut1xx.dts index 15f20178642c..eb4f0bf074da 100644 --- a/arch/arm/boot/dts/gemini-rut1xx.dts +++ b/arch/arm/boot/dts/gemini-rut1xx.dts @@ -14,7 +14,7 @@ #address-cells = <1>; #size-cells = <1>; - memory { /* 128 MB */ + memory@0 { /* 128 MB */ device_type = "memory"; reg = <0x00000000 0x8000000>; }; @@ -26,11 +26,9 @@ gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - button@28 { - debounce_interval = <50>; + button-setup { + debounce-interval = <50>; wakeup-source; linux,code = <KEY_SETUP>; label = "Reset to defaults"; @@ -41,14 +39,14 @@ leds { compatible = "gpio-leds"; - led@7 { + led-gsm { /* FIXME: add the LED color */ label = "rut1xx::gsm"; /* Conflict with ICE */ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - led@31 { + led-power { /* FIXME: add the LED color */ label = "rut1xx::power"; /* Conflict with NAND CE0 */ diff --git a/arch/arm/boot/dts/gemini-sq201.dts b/arch/arm/boot/dts/gemini-sq201.dts index 63c02ca9513c..e5cf9d1a98cd 100644 --- a/arch/arm/boot/dts/gemini-sq201.dts +++ b/arch/arm/boot/dts/gemini-sq201.dts @@ -14,7 +14,7 @@ #address-cells = <1>; #size-cells = <1>; - memory { /* 128 MB */ + memory@0 { /* 128 MB */ device_type = "memory"; reg = <0x00000000 0x8000000>; }; @@ -26,11 +26,9 @@ gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - button@18 { - debounce_interval = <50>; + button-setup { + debounce-interval = <50>; wakeup-source; linux,code = <KEY_SETUP>; label = "factory reset"; @@ -41,14 +39,14 @@ leds { compatible = "gpio-leds"; - led@20 { + led-green-info { label = "sq201:green:info"; /* Conflict with parallel flash */ gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>; default-state = "on"; linux,default-trigger = "heartbeat"; }; - led@31 { + led-green-usb { label = "sq201:green:usb"; /* Conflict with parallel and NAND flash */ gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; diff --git a/arch/arm/boot/dts/gemini-wbd111.dts b/arch/arm/boot/dts/gemini-wbd111.dts index b4ec9ad85d72..29af86cd10f7 100644 --- a/arch/arm/boot/dts/gemini-wbd111.dts +++ b/arch/arm/boot/dts/gemini-wbd111.dts @@ -14,7 +14,8 @@ #address-cells = <1>; #size-cells = <1>; - memory { /* 128 MB */ + memory@0 { + /* 128 MB */ device_type = "memory"; reg = <0x00000000 0x8000000>; }; @@ -26,11 +27,9 @@ gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - button@5 { - debounce_interval = <50>; + button-setup { + debounce-interval = <50>; wakeup-source; linux,code = <KEY_SETUP>; label = "reset"; @@ -42,25 +41,25 @@ leds { compatible = "gpio-leds"; - led@1 { + led-red-l3 { label = "wbd111:red:L3"; /* Conflict with TVC and extended parallel flash */ gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led@2 { + led-green-l4 { label = "wbd111:green:L4"; /* Conflict with TVC and extended parallel flash */ gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led@3 { + led-red-l4 { label = "wbd111:red:L4"; /* Conflict with TVC and extended parallel flash */ gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led@5 { + led-greeb-l3 { label = "wbd111:green:L3"; /* Conflict with TVC and extended parallel flash */ gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; diff --git a/arch/arm/boot/dts/gemini-wbd222.dts b/arch/arm/boot/dts/gemini-wbd222.dts index 6d25bcc046e7..24e6ae3616f7 100644 --- a/arch/arm/boot/dts/gemini-wbd222.dts +++ b/arch/arm/boot/dts/gemini-wbd222.dts @@ -14,7 +14,7 @@ #address-cells = <1>; #size-cells = <1>; - memory { /* 128 MB */ + memory@0 { /* 128 MB */ device_type = "memory"; reg = <0x00000000 0x8000000>; }; @@ -26,11 +26,9 @@ gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - button@5 { - debounce_interval = <50>; + button-setup { + debounce-interval = <50>; wakeup-source; linux,code = <KEY_SETUP>; label = "reset"; @@ -42,25 +40,25 @@ leds { compatible = "gpio-leds"; - led@1 { + led-red-l3 { label = "wbd111:red:L3"; /* Conflict with TVC and extended parallel flash */ gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led@2 { + led-green-l4 { label = "wbd111:green:L4"; /* Conflict with TVC and extended parallel flash */ gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led@3 { + led-red-l4 { label = "wbd111:red:L4"; /* Conflict with TVC and extended parallel flash */ gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led@5 { + led-green-l3 { label = "wbd111:green:L3"; /* Conflict with TVC and extended parallel flash */ gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; diff --git a/arch/arm/boot/dts/gemini.dtsi b/arch/arm/boot/dts/gemini.dtsi index 0568baca500a..eb752e9495de 100644 --- a/arch/arm/boot/dts/gemini.dtsi +++ b/arch/arm/boot/dts/gemini.dtsi @@ -3,8 +3,6 @@ * Device Tree file for Cortina systems Gemini SoC */ -/include/ "skeleton.dtsi" - #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/clock/cortina,gemini-clock.h> #include <dt-bindings/reset/cortina,gemini-reset.h> diff --git a/arch/arm/boot/dts/imx1-ads.dts b/arch/arm/boot/dts/imx1-ads.dts index 6354e4c87313..a1d81badb5c8 100644 --- a/arch/arm/boot/dts/imx1-ads.dts +++ b/arch/arm/boot/dts/imx1-ads.dts @@ -23,17 +23,6 @@ memory@8000000 { reg = <0x08000000 0x04000000>; }; - - clocks { - #address-cells = <1>; - #size-cells = <0>; - - clk32 { - compatible = "fsl,imx-clk32", "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <32000>; - }; - }; }; &cspi1 { diff --git a/arch/arm/boot/dts/imx1.dtsi b/arch/arm/boot/dts/imx1.dtsi index f7b9edf93f5e..3edc7b5550d8 100644 --- a/arch/arm/boot/dts/imx1.dtsi +++ b/arch/arm/boot/dts/imx1.dtsi @@ -1,13 +1,6 @@ -/* - * Copyright (C) 2014 Alexander Shiyan <shc_work@mail.ru> - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright (C) 2014 Alexander Shiyan <shc_work@mail.ru> #include "imx1-pinfunc.h" @@ -62,6 +55,14 @@ }; }; + clocks { + clk32 { + compatible = "fsl,imx-clk32", "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32000>; + }; + }; + soc { #address-cells = <1>; #size-cells = <1>; diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts index 9d92ece82560..9fb47724b9c1 100644 --- a/arch/arm/boot/dts/imx23-evk.dts +++ b/arch/arm/boot/dts/imx23-evk.dts @@ -1,13 +1,6 @@ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Freescale Semiconductor, Inc. /dts-v1/; #include "imx23.dtsi" diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/imx23.dtsi index cb0a3fe32718..71bfd2b15609 100644 --- a/arch/arm/boot/dts/imx23.dtsi +++ b/arch/arm/boot/dts/imx23.dtsi @@ -1,13 +1,6 @@ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Freescale Semiconductor, Inc. #include "imx23-pinfunc.h" diff --git a/arch/arm/boot/dts/imx25-pdk.dts b/arch/arm/boot/dts/imx25-pdk.dts index 7f9bd052b84e..a5626b46ac4e 100644 --- a/arch/arm/boot/dts/imx25-pdk.dts +++ b/arch/arm/boot/dts/imx25-pdk.dts @@ -1,13 +1,6 @@ -/* - * Copyright 2013 Freescale Semiconductor, Inc. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2013 Freescale Semiconductor, Inc. /dts-v1/; #include <dt-bindings/gpio/gpio.h> @@ -291,7 +284,6 @@ }; &ssi1 { - codec-handle = <&codec>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/imx25.dtsi index cf70df20b19c..85c15ee63272 100644 --- a/arch/arm/boot/dts/imx25.dtsi +++ b/arch/arm/boot/dts/imx25.dtsi @@ -1,13 +1,6 @@ -/* - * Copyright 2012 Sascha Hauer, Pengutronix <s.hauer@pengutronix.de> - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Sascha Hauer, Pengutronix <s.hauer@pengutronix.de> #include <dt-bindings/gpio/gpio.h> #include "imx25-pinfunc.h" @@ -70,9 +63,6 @@ }; clocks { - #address-cells = <1>; - #size-cells = <0>; - osc { compatible = "fsl,imx-osc", "fixed-clock"; #clock-cells = <0>; diff --git a/arch/arm/boot/dts/imx27-apf27.dts b/arch/arm/boot/dts/imx27-apf27.dts index 66941cdbf244..3eddd805a793 100644 --- a/arch/arm/boot/dts/imx27-apf27.dts +++ b/arch/arm/boot/dts/imx27-apf27.dts @@ -22,17 +22,10 @@ memory@a0000000 { reg = <0xa0000000 0x04000000>; }; +}; - clocks { - #address-cells = <1>; - #size-cells = <0>; - - osc26m { - compatible = "fsl,imx-osc26m", "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <0>; - }; - }; +&clk_osc26m { + clock-frequency = <0>; }; &iomuxc { diff --git a/arch/arm/boot/dts/imx27-pdk.dts b/arch/arm/boot/dts/imx27-pdk.dts index 924b90c9985d..f9a882d99132 100644 --- a/arch/arm/boot/dts/imx27-pdk.dts +++ b/arch/arm/boot/dts/imx27-pdk.dts @@ -1,13 +1,6 @@ -/* - * Copyright 2012 Sascha Hauer, Pengutronix - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Sascha Hauer, Pengutronix /dts-v1/; #include "imx27.dtsi" diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi index 6585b00c3917..753d88df1627 100644 --- a/arch/arm/boot/dts/imx27.dtsi +++ b/arch/arm/boot/dts/imx27.dtsi @@ -1,13 +1,6 @@ -/* - * Copyright 2012 Sascha Hauer, Pengutronix - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Sascha Hauer, Pengutronix #include "imx27-pinfunc.h" @@ -57,10 +50,7 @@ }; clocks { - #address-cells = <1>; - #size-cells = <0>; - - osc26m { + clk_osc26m: osc26m { compatible = "fsl,imx-osc26m", "fixed-clock"; #clock-cells = <0>; clock-frequency = <26000000>; diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts index 60e5c7fd5035..f1c8315b3e01 100644 --- a/arch/arm/boot/dts/imx28-cfa10049.dts +++ b/arch/arm/boot/dts/imx28-cfa10049.dts @@ -398,8 +398,6 @@ compatible = "gpio-keys"; pinctrl-names = "default"; pinctrl-0 = <&rotary_btn_pins_cfa10049>; - #address-cells = <1>; - #size-cells = <0>; rotary_button { label = "rotary_button"; diff --git a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts index 7f8d40a9c67e..22215337f72a 100644 --- a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts +++ b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts @@ -206,8 +206,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&enocean_button>; diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts index b0d39654aeb3..6b0ae667640f 100644 --- a/arch/arm/boot/dts/imx28-evk.dts +++ b/arch/arm/boot/dts/imx28-evk.dts @@ -1,13 +1,6 @@ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Freescale Semiconductor, Inc. /dts-v1/; #include "imx28.dtsi" diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/imx28-tx28.dts index 687186358c18..b8f46432e2a2 100644 --- a/arch/arm/boot/dts/imx28-tx28.dts +++ b/arch/arm/boot/dts/imx28-tx28.dts @@ -140,15 +140,10 @@ regulator-boot-on; }; - clocks { - #address-cells = <1>; - #size-cells = <0>; - mclk: clock@0 { - compatible = "fixed-clock"; - reg = <0>; - #clock-cells = <0>; - clock-frequency = <26000000>; - }; + mclk: clock-mclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; }; sound { @@ -345,6 +340,7 @@ interrupts = <5 IRQ_TYPE_EDGE_FALLING>; reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>; + wakeup-source; }; touchscreen: tsc2007@48 { diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 9ad8d3556859..5107fdc482ea 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -1,13 +1,6 @@ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Freescale Semiconductor, Inc. #include <dt-bindings/gpio/gpio.h> #include "imx28-pinfunc.h" diff --git a/arch/arm/boot/dts/imx31.dtsi b/arch/arm/boot/dts/imx31.dtsi index ebc3f2dbb6fd..4642c8169a65 100644 --- a/arch/arm/boot/dts/imx31.dtsi +++ b/arch/arm/boot/dts/imx31.dtsi @@ -1,13 +1,6 @@ -/* - * Copyright 2012 Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> / { #address-cells = <1>; diff --git a/arch/arm/boot/dts/imx35-pdk.dts b/arch/arm/boot/dts/imx35-pdk.dts index 646b1257bba2..df613e88fd2c 100644 --- a/arch/arm/boot/dts/imx35-pdk.dts +++ b/arch/arm/boot/dts/imx35-pdk.dts @@ -1,14 +1,7 @@ -/* - * Copyright 2013 Eukréa Electromatique <denis@eukrea.com> - * Copyright 2014 Freescale Semiconductor, Inc. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2013 Eukréa Electromatique <denis@eukrea.com> +// Copyright 2014 Freescale Semiconductor, Inc. /dts-v1/; #include "imx35.dtsi" diff --git a/arch/arm/boot/dts/imx35.dtsi b/arch/arm/boot/dts/imx35.dtsi index 54111ed218b1..1c50b785cad4 100644 --- a/arch/arm/boot/dts/imx35.dtsi +++ b/arch/arm/boot/dts/imx35.dtsi @@ -1,12 +1,8 @@ -/* - * Copyright 2012 Steffen Trumtrar, Pengutronix - * - * based on imx27.dtsi - * - * This program is free software; you can redistribute it and/or modify it under - * the terms of the GNU General Public License version 2 as published by the - * Free Software Foundation. - */ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright 2012 Steffen Trumtrar, Pengutronix +// +// based on imx27.dtsi #include "imx35-pinfunc.h" diff --git a/arch/arm/boot/dts/imx50-evk.dts b/arch/arm/boot/dts/imx50-evk.dts index 23f1833e23fa..f0622ec4ba9c 100644 --- a/arch/arm/boot/dts/imx50-evk.dts +++ b/arch/arm/boot/dts/imx50-evk.dts @@ -1,15 +1,8 @@ -/* - * Copyright 2013 Greg Ungerer <gerg@uclinux.org> - * Copyright 2011 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2013 Greg Ungerer <gerg@uclinux.org> +// Copyright 2011 Freescale Semiconductor, Inc. +// Copyright 2011 Linaro Ltd. /dts-v1/; #include "imx50.dtsi" diff --git a/arch/arm/boot/dts/imx50.dtsi b/arch/arm/boot/dts/imx50.dtsi index 7954e79d0a16..a9b712db9f6c 100644 --- a/arch/arm/boot/dts/imx50.dtsi +++ b/arch/arm/boot/dts/imx50.dtsi @@ -60,9 +60,6 @@ }; clocks { - #address-cells = <1>; - #size-cells = <0>; - ckil { compatible = "fsl,imx-ckil", "fixed-clock"; #clock-cells = <0>; diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/imx51-babbage.dts index cf7a1963df25..b8ca73d3d379 100644 --- a/arch/arm/boot/dts/imx51-babbage.dts +++ b/arch/arm/boot/dts/imx51-babbage.dts @@ -1,14 +1,7 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2011 Freescale Semiconductor, Inc. +// Copyright 2011 Linaro Ltd. /dts-v1/; #include "imx51.dtsi" diff --git a/arch/arm/boot/dts/imx51-zii-rdu1.dts b/arch/arm/boot/dts/imx51-zii-rdu1.dts index 0c99ac04ad08..df9eca94d812 100644 --- a/arch/arm/boot/dts/imx51-zii-rdu1.dts +++ b/arch/arm/boot/dts/imx51-zii-rdu1.dts @@ -207,8 +207,6 @@ switch@0 { compatible = "marvell,mv88e6085"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; dsa,member = <0 0>; @@ -462,7 +460,10 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_esdhc1>; bus-width = <4>; + no-1-8-v; non-removable; + no-sdio; + no-sd; status = "okay"; }; @@ -523,7 +524,7 @@ }; touchscreen@20 { - compatible = "syna,rmi4_i2c"; + compatible = "syna,rmi4-i2c"; reg = <0x20>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ts>; @@ -541,8 +542,8 @@ rmi4-f11@11 { reg = <0x11>; - touch-inverted-y; - touch-swapped-x-y; + touchscreen-inverted-y; + touchscreen-swapped-x-y; syna,sensor-type = <1>; }; }; @@ -591,6 +592,7 @@ phy_type = "ulpi"; fsl,usbphy = <&usbh1phy>; disable-over-current; + maximum-speed = "full-speed"; vbus-supply = <®_5p0v_main>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx51.dtsi b/arch/arm/boot/dts/imx51.dtsi index 5d390a64e976..fe01b890c715 100644 --- a/arch/arm/boot/dts/imx51.dtsi +++ b/arch/arm/boot/dts/imx51.dtsi @@ -1,14 +1,7 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2011 Freescale Semiconductor, Inc. +// Copyright 2011 Linaro Ltd. #include "imx51-pinfunc.h" #include <dt-bindings/clock/imx5-clock.h> @@ -56,9 +49,6 @@ }; clocks { - #address-cells = <1>; - #size-cells = <0>; - ckil { compatible = "fsl,imx-ckil", "fixed-clock"; #clock-cells = <0>; diff --git a/arch/arm/boot/dts/imx53-ard.dts b/arch/arm/boot/dts/imx53-ard.dts index 80fc00705d92..117bd002dd1d 100644 --- a/arch/arm/boot/dts/imx53-ard.dts +++ b/arch/arm/boot/dts/imx53-ard.dts @@ -11,6 +11,7 @@ */ /dts-v1/; +#include <dt-bindings/input/input.h> #include "imx53.dtsi" / { @@ -68,34 +69,34 @@ home { label = "Home"; gpios = <&gpio5 10 0>; - linux,code = <102>; /* KEY_HOME */ + linux,code = <KEY_HOME>; wakeup-source; }; back { label = "Back"; gpios = <&gpio5 11 0>; - linux,code = <158>; /* KEY_BACK */ + linux,code = <KEY_BACK>; wakeup-source; }; program { label = "Program"; gpios = <&gpio5 12 0>; - linux,code = <362>; /* KEY_PROGRAM */ + linux,code = <KEY_PROGRAM >; wakeup-source; }; volume-up { label = "Volume Up"; gpios = <&gpio5 13 0>; - linux,code = <115>; /* KEY_VOLUMEUP */ + linux,code = <KEY_VOLUMEUP>; }; volume-down { label = "Volume Down"; gpios = <&gpio4 0 0>; - linux,code = <114>; /* KEY_VOLUMEDOWN */ + linux,code = <KEY_VOLUMEDOWN>; }; }; }; diff --git a/arch/arm/boot/dts/imx53-m53.dtsi b/arch/arm/boot/dts/imx53-m53.dtsi index 3da6dd5edb79..ce45f08e3051 100644 --- a/arch/arm/boot/dts/imx53-m53.dtsi +++ b/arch/arm/boot/dts/imx53-m53.dtsi @@ -53,8 +53,6 @@ stmpe610@41 { compatible = "st,stmpe610"; - #address-cells = <1>; - #size-cells = <0>; reg = <0x41>; id = <0>; blocks = <0x5>; diff --git a/arch/arm/boot/dts/imx53-ppd.dts b/arch/arm/boot/dts/imx53-ppd.dts index d5628af2e301..3aa6f693fa9f 100644 --- a/arch/arm/boot/dts/imx53-ppd.dts +++ b/arch/arm/boot/dts/imx53-ppd.dts @@ -180,8 +180,6 @@ power-gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; power-button { label = "Power button"; @@ -192,8 +190,6 @@ touch-lock-key { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; touch-lock-button { label = "Touch lock button"; @@ -300,7 +296,7 @@ compatible = "dlg,da9053-aa"; reg = <0>; interrupt-parent = <&gpio3>; - interrupts = <12 0x8>; + interrupts = <12 IRQ_TYPE_LEVEL_LOW>; spi-max-frequency = <1000000>; dlg,tsi-as-adc; tsiref-supply = <®_tsiref>; @@ -473,7 +469,7 @@ compatible = "fsl,mma8453"; reg = <0x1c>; interrupt-parent = <&gpio1>; - interrupts = <6 0>; + interrupts = <6 IRQ_TYPE_NONE>; interrupt-names = "INT1"; }; @@ -539,7 +535,7 @@ reset-gpio = <&gpio5 19 GPIO_ACTIVE_HIGH>; reg = <0x4b>; interrupt-parent = <&gpio5>; - interrupts = <4 0x8>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; }; }; @@ -559,8 +555,6 @@ status = "okay"; port@2 { - reg = <2>; - lvds0_out: endpoint { remote-endpoint = <&panel_in_lvds0>; }; diff --git a/arch/arm/boot/dts/imx53-qsb-common.dtsi b/arch/arm/boot/dts/imx53-qsb-common.dtsi index 485a69d45e1c..ef7658a78836 100644 --- a/arch/arm/boot/dts/imx53-qsb-common.dtsi +++ b/arch/arm/boot/dts/imx53-qsb-common.dtsi @@ -1,14 +1,7 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2011 Freescale Semiconductor, Inc. +// Copyright 2011 Linaro Ltd. #include "imx53.dtsi" diff --git a/arch/arm/boot/dts/imx53-qsb.dts b/arch/arm/boot/dts/imx53-qsb.dts index d3d662e37677..6831836bd726 100644 --- a/arch/arm/boot/dts/imx53-qsb.dts +++ b/arch/arm/boot/dts/imx53-qsb.dts @@ -1,14 +1,7 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2011 Freescale Semiconductor, Inc. +// Copyright 2011 Linaro Ltd. /dts-v1/; #include "imx53-qsb-common.dtsi" @@ -23,7 +16,7 @@ compatible = "dlg,da9053-aa", "dlg,da9052"; reg = <0x48>; interrupt-parent = <&gpio7>; - interrupts = <11 0x8>; /* low-level active IRQ at GPIO7_11 */ + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; /* low-level active IRQ at GPIO7_11 */ regulators { buck1_reg: buck1 { diff --git a/arch/arm/boot/dts/imx53-qsrb.dts b/arch/arm/boot/dts/imx53-qsrb.dts index 4e103a905dc9..1bbf24ad308a 100644 --- a/arch/arm/boot/dts/imx53-qsrb.dts +++ b/arch/arm/boot/dts/imx53-qsrb.dts @@ -1,14 +1,7 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2011 Freescale Semiconductor, Inc. +// Copyright 2011 Linaro Ltd. /dts-v1/; diff --git a/arch/arm/boot/dts/imx53-smd.dts b/arch/arm/boot/dts/imx53-smd.dts index fd030128666c..462071c9ddd7 100644 --- a/arch/arm/boot/dts/imx53-smd.dts +++ b/arch/arm/boot/dts/imx53-smd.dts @@ -1,16 +1,10 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2011 Freescale Semiconductor, Inc. +// Copyright 2011 Linaro Ltd. /dts-v1/; +#include <dt-bindings/input/input.h> #include "imx53.dtsi" / { @@ -27,13 +21,13 @@ volume-up { label = "Volume Up"; gpios = <&gpio2 14 0>; - linux,code = <115>; /* KEY_VOLUMEUP */ + linux,code = <KEY_VOLUMEUP>; }; volume-down { label = "Volume Down"; gpios = <&gpio2 15 0>; - linux,code = <114>; /* KEY_VOLUMEDOWN */ + linux,code = <KEY_VOLUMEDOWN>; }; }; }; diff --git a/arch/arm/boot/dts/imx53-tx53-x03x.dts b/arch/arm/boot/dts/imx53-tx53-x03x.dts index af8ec5e4417b..a7f77527269d 100644 --- a/arch/arm/boot/dts/imx53-tx53-x03x.dts +++ b/arch/arm/boot/dts/imx53-tx53-x03x.dts @@ -245,6 +245,7 @@ interrupts = <15 IRQ_TYPE_EDGE_FALLING>; reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; wake-gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; + wakeup-source; }; touchscreen: tsc2007@48 { diff --git a/arch/arm/boot/dts/imx53-tx53.dtsi b/arch/arm/boot/dts/imx53-tx53.dtsi index 69a2af7d6c11..54cf3e67069a 100644 --- a/arch/arm/boot/dts/imx53-tx53.dtsi +++ b/arch/arm/boot/dts/imx53-tx53.dtsi @@ -58,7 +58,7 @@ can0 = &can2; /* Make the can interface indices consistent with TX28/TX48 modules */ can1 = &can1; ipu = &ipu; - reg_can_xcvr = ®_can_xcvr; + reg-can-xcvr = ®_can_xcvr; usbh1 = &usbh1; usbotg = &usbotg; }; @@ -67,13 +67,12 @@ ckih1 { clock-frequency = <0>; }; + }; - mclk: clock@0 { - compatible = "fixed-clock"; - reg = <0>; - #clock-cells = <0>; - clock-frequency = <26000000>; - }; + mclk: clock-mclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; }; gpio-keys { @@ -550,7 +549,6 @@ }; &ssi1 { - codec-handle = <&sgtl5000>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi b/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi index df8dafe2564d..f83a8c62ea53 100644 --- a/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi +++ b/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi @@ -150,7 +150,7 @@ compatible = "dlg,da9053-aa", "dlg,da9052"; reg = <0x48>; interrupt-parent = <&gpio7>; - interrupts = <11 0x8>; /* low-level active IRQ at GPIO7_11 */ + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; /* low-level active IRQ at GPIO7_11 */ regulators { buck1_reg: buck1 { diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi index 3d65c0192f69..1a7a7bb3df45 100644 --- a/arch/arm/boot/dts/imx53.dtsi +++ b/arch/arm/boot/dts/imx53.dtsi @@ -88,9 +88,6 @@ }; clocks { - #address-cells = <1>; - #size-cells = <0>; - ckil { compatible = "fsl,imx-ckil", "fixed-clock"; #clock-cells = <0>; @@ -488,6 +485,10 @@ remote-endpoint = <&ipu_di0_lvds0>; }; }; + + port@2 { + reg = <2>; + }; }; lvds-channel@1 { @@ -503,6 +504,10 @@ remote-endpoint = <&ipu_di1_lvds1>; }; }; + + port@2 { + reg = <2>; + }; }; }; diff --git a/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts b/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts index 7128c76d5721..29940ba215a8 100644 --- a/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts +++ b/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts @@ -78,8 +78,6 @@ &ecspi1 { lcd_panel: display@0 { - #address-cells = <1>; - #size-cells = <1>; compatible = "lg,lg4573"; spi-max-frequency = <10000000>; reg = <0>; diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts index ea184d108491..3dee3af1a4c1 100644 --- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts +++ b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts @@ -72,15 +72,12 @@ stdout-path = "serial0:115200n8"; }; - clocks { - /* Fixed crystal dedicated to mcp251x */ - clk16m: clk@1 { - compatible = "fixed-clock"; - reg = <1>; - #clock-cells = <0>; - clock-frequency = <16000000>; - clock-output-names = "clk16m"; - }; + /* Fixed crystal dedicated to mcp251x */ + clk16m: clock-16m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <16000000>; + clock-output-names = "clk16m"; }; gpio-keys { diff --git a/arch/arm/boot/dts/imx6dl-mamoj.dts b/arch/arm/boot/dts/imx6dl-mamoj.dts new file mode 100644 index 000000000000..6b2d29138bed --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-mamoj.dts @@ -0,0 +1,224 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2018 BTicino + * Copyright (C) 2018 Amarula Solutions B.V. + */ + +/dts-v1/; + +#include "imx6dl.dtsi" + +/ { + model = "BTicino i.MX6DL Mamoj board"; + compatible = "bticino,imx6dl-mamoj", "fsl,imx6dl"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "mii"; + status = "okay"; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + pfuze100: pmic@8 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + /* CPU vdd_arm core */ + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + /* SOC vdd_soc */ + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + /* I/O power GEN_3V3 */ + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + /* DDR memory */ + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + /* DDR memory */ + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + /* not used */ + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + /* not used */ + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + /* PMIC vsnvs. EX boot mode */ + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + /* not used */ + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + /* not used */ + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + /* not used */ + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + /* 1v8 general power */ + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + /* 2v8 general power IMX6 */ + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + /* 3v3 Ethernet */ + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + bus-width = <8>; + non-removable; + keep-power-in-suspend; + status = "okay"; +}; + +&iomuxc { + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b1 + MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0 + MX6QDL_PAD_KEY_ROW2__ENET_TX_DATA2 0x1b0b0 + MX6QDL_PAD_KEY_ROW0__ENET_TX_DATA3 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + MX6QDL_PAD_GPIO_19__ENET_TX_ER 0x1b0b0 + MX6QDL_PAD_GPIO_18__ENET_RX_CLK 0x1b0b1 + MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0 + MX6QDL_PAD_KEY_COL2__ENET_RX_DATA2 0x1b0b0 + MX6QDL_PAD_KEY_COL0__ENET_RX_DATA3 0x1b0b0 + MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0 + MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0 + MX6QDL_PAD_KEY_COL3__ENET_CRS 0x1b0b0 + MX6QDL_PAD_KEY_ROW1__ENET_COL 0x1b0b0 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX6QDL_PAD_GPIO_7__I2C4_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_8__I2C4_SDA 0x4001b8b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059 + >; + }; +}; diff --git a/arch/arm/boot/dts/imx6dl-sabreauto.dts b/arch/arm/boot/dts/imx6dl-sabreauto.dts index a6ce7b487ad7..660d52a245ba 100644 --- a/arch/arm/boot/dts/imx6dl-sabreauto.dts +++ b/arch/arm/boot/dts/imx6dl-sabreauto.dts @@ -1,10 +1,6 @@ -/* - * Copyright (C) 2013 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright (C) 2013 Freescale Semiconductor, Inc. /dts-v1/; diff --git a/arch/arm/boot/dts/imx6dl-sabresd.dts b/arch/arm/boot/dts/imx6dl-sabresd.dts index 9607afe088fc..cd6bbf22a16f 100644 --- a/arch/arm/boot/dts/imx6dl-sabresd.dts +++ b/arch/arm/boot/dts/imx6dl-sabresd.dts @@ -1,10 +1,6 @@ -/* - * Copyright (C) 2013 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright (C) 2013 Freescale Semiconductor, Inc. /dts-v1/; diff --git a/arch/arm/boot/dts/imx6dl-udoo.dts b/arch/arm/boot/dts/imx6dl-udoo.dts index e3713f00e819..d871cac1711f 100644 --- a/arch/arm/boot/dts/imx6dl-udoo.dts +++ b/arch/arm/boot/dts/imx6dl-udoo.dts @@ -1,12 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright 2013 Freescale Semiconductor, Inc. * * Author: Fabio Estevam <fabio.estevam@freescale.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * */ /dts-v1/; #include "imx6dl.dtsi" diff --git a/arch/arm/boot/dts/imx6dl-wandboard-revb1.dts b/arch/arm/boot/dts/imx6dl-wandboard-revb1.dts index 5727fa48cfd5..738db4fc7702 100644 --- a/arch/arm/boot/dts/imx6dl-wandboard-revb1.dts +++ b/arch/arm/boot/dts/imx6dl-wandboard-revb1.dts @@ -1,12 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright 2013 Freescale Semiconductor, Inc. * * Author: Fabio Estevam <fabio.estevam@freescale.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * */ /dts-v1/; #include "imx6dl.dtsi" diff --git a/arch/arm/boot/dts/imx6dl-wandboard-revd1.dts b/arch/arm/boot/dts/imx6dl-wandboard-revd1.dts index a72c07db7dda..51de6b4bd7d8 100644 --- a/arch/arm/boot/dts/imx6dl-wandboard-revd1.dts +++ b/arch/arm/boot/dts/imx6dl-wandboard-revd1.dts @@ -1,12 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright 2013 Freescale Semiconductor, Inc. * * Author: Fabio Estevam <fabio.estevam@freescale.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * */ /dts-v1/; #include "imx6dl.dtsi" diff --git a/arch/arm/boot/dts/imx6dl-wandboard.dts b/arch/arm/boot/dts/imx6dl-wandboard.dts index a09f274cd1f4..b43454deaa1a 100644 --- a/arch/arm/boot/dts/imx6dl-wandboard.dts +++ b/arch/arm/boot/dts/imx6dl-wandboard.dts @@ -1,12 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright 2013 Freescale Semiconductor, Inc. * * Author: Fabio Estevam <fabio.estevam@freescale.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * */ /dts-v1/; #include "imx6dl.dtsi" diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi index 558bce81209d..b384913c34dd 100644 --- a/arch/arm/boot/dts/imx6dl.dtsi +++ b/arch/arm/boot/dts/imx6dl.dtsi @@ -1,12 +1,6 @@ - -/* - * Copyright 2013 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - */ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright 2013 Freescale Semiconductor, Inc. #include <dt-bindings/interrupt-controller/irq.h> #include "imx6dl-pinfunc.h" diff --git a/arch/arm/boot/dts/imx6q-b850v3.dts b/arch/arm/boot/dts/imx6q-b850v3.dts index 35edbdc7bcd1..044a5bebe1c5 100644 --- a/arch/arm/boot/dts/imx6q-b850v3.dts +++ b/arch/arm/boot/dts/imx6q-b850v3.dts @@ -156,8 +156,6 @@ stdp2690@72 { compatible = "megachips,stdp2690-ge-b850v3-fw"; - #address-cells = <1>; - #size-cells = <0>; reg = <0x72>; ports { @@ -184,8 +182,6 @@ stdp4028@73 { compatible = "megachips,stdp4028-ge-b850v3-fw"; - #address-cells = <1>; - #size-cells = <0>; reg = <0x73>; interrupt-parent = <&gpio2>; interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; diff --git a/arch/arm/boot/dts/imx6q-ba16.dtsi b/arch/arm/boot/dts/imx6q-ba16.dtsi index bf4bdb385de9..e903c488287b 100644 --- a/arch/arm/boot/dts/imx6q-ba16.dtsi +++ b/arch/arm/boot/dts/imx6q-ba16.dtsi @@ -157,7 +157,12 @@ partition@d0000 { label = "spare"; - reg = <0xd0000 0x130000>; + reg = <0xd0000 0x320000>; + }; + + partition@3f0000 { + label = "mfg"; + reg = <0x3f0000 0x10000>; }; }; }; diff --git a/arch/arm/boot/dts/imx6q-bx50v3.dtsi b/arch/arm/boot/dts/imx6q-bx50v3.dtsi index 990e411cbca0..d3cba09be0cb 100644 --- a/arch/arm/boot/dts/imx6q-bx50v3.dtsi +++ b/arch/arm/boot/dts/imx6q-bx50v3.dtsi @@ -43,13 +43,10 @@ #include "imx6q-ba16.dtsi" / { - clocks { - mclk: clock@0 { - compatible = "fixed-clock"; - reg = <0>; - #clock-cells = <0>; - clock-frequency = <22000000>; - }; + mclk: clock-mclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <22000000>; }; gpio-poweroff { @@ -107,8 +104,6 @@ switch@0 { compatible = "marvell,mv88e6085"; /* 88e6240*/ - #address-cells = <1>; - #size-cells = <0>; reg = <0>; switch_ports: ports { diff --git a/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts b/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts new file mode 100644 index 000000000000..9c61e3be2d9a --- /dev/null +++ b/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts @@ -0,0 +1,151 @@ +// SPDX-License-Identifier: (GPL-2.0+) +/* + * Copyright (C) 2015 DH electronics GmbH + * Copyright (C) 2018 Marek Vasut <marex@denx.de> + */ + +/dts-v1/; + +#include "imx6q-dhcom-som.dtsi" + +/ { + model = "Freescale i.MX6 Quad DHCOM Premium Developer Kit (2)"; + compatible = "dh,imx6q-dhcom-pdk2", "dh,imx6q-dhcom-som", "fsl,imx6q"; + + chosen { + stdout-path = &uart1; + }; + + clk_ext_audio_codec: clock-codec { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + }; + + sound { + compatible = "fsl,imx-audio-sgtl5000"; + model = "imx-sgtl5000"; + ssi-controller = <&ssi1>; + audio-codec = <&sgtl5000>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "LINE_IN", "Line In Jack", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <3>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux_ext>; + status = "okay"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c2>; + status = "okay"; +}; + +&i2c2 { + sgtl5000: codec@a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + #sound-dai-cells = <0>; + clocks = <&clk_ext_audio_codec>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog_base &pinctrl_hog>; + + pinctrl_hog: hog-grp { + fsl,pins = < + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x400120b0 + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x400120b0 + MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x400120b0 + MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03 0x400120b0 + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x120b0 + MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x400120b0 + MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x120b0 + MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x120b0 + MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x400120b0 + MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x400120b0 + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x400120b0 + MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x400120b0 + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x400120b0 + MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x400120b0 + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x400120b0 + MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x400120b0 + MX6QDL_PAD_SD1_CMD__GPIO1_IO18 0x400120b0 + MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x400120b0 + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x400120b0 + MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x400120b0 + MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x400120b0 + MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x400120b0 + MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x400120b0 + MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x400120b0 + >; + }; + + pinctrl_audmux_ext: audmux-ext-grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_enet_1G: enet-1G-grp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x000b0 + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x000b1 + MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x000b1 + >; + }; + + pinctrl_pcie: pcie-grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b1 + >; + }; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie>; + reset-gpio = <&gpio6 14 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&ssi1 { + status = "okay"; +}; + +&sata { + status = "okay"; +}; + +&usdhc3 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-dhcom-som.dtsi b/arch/arm/boot/dts/imx6q-dhcom-som.dtsi new file mode 100644 index 000000000000..bbba0671f0f4 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-dhcom-som.dtsi @@ -0,0 +1,476 @@ +// SPDX-License-Identifier: (GPL-2.0+) +/* + * Copyright (C) 2015 DH electronics GmbH + * Copyright (C) 2018 Marek Vasut <marex@denx.de> + */ + +#include "imx6q.dtsi" +#include <dt-bindings/pwm/pwm.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/clock/imx6qdl-clock.h> +#include <dt-bindings/input/input.h> + +/ { + aliases { + mmc0 = &usdhc2; + mmc1 = &usdhc3; + mmc2 = &usdhc4; + mmc3 = &usdhc1; + }; + + memory@10000000 { + reg = <0x10000000 0x40000000>; + }; + + reg_usb_otg_vbus: regulator-usb-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_usb_h1_vbus: regulator-usb-h1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_h1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_3p3v: regulator-3P3V { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + status = "okay"; +}; + +&ecspi1 { + cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>, <&gpio4 11 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash@0 { /* S25FL116K */ + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; + m25p,fast-read; + }; +}; + +&ecspi2 { + cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_100M>; + phy-mode = "rmii"; + phy-handle = <ðphy0>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { /* SMSC LAN8710Ai */ + reg = <0>; + max-speed = <100>; + reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + reset-delay-us = <1000>; + reset-post-delay-us = <1000>; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + ltc3676: pmic@3c { + compatible = "lltc,ltc3676"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic_hw300>; + reg = <0x3c>; + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + + regulators { + sw1_reg: sw1 { + regulator-min-microvolt = <787500>; + regulator-max-microvolt = <1527272>; + lltc,fb-voltage-divider = <100000 110000>; + regulator-suspend-mem-microvolt = <1040000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <1885714>; + regulator-max-microvolt = <3657142>; + lltc,fb-voltage-divider = <100000 28000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: sw3 { + regulator-min-microvolt = <787500>; + regulator-max-microvolt = <1527272>; + lltc,fb-voltage-divider = <100000 110000>; + regulator-suspend-mem-microvolt = <980000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <855571>; + regulator-max-microvolt = <1659291>; + lltc,fb-voltage-divider = <100000 93100>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: ldo1 { + regulator-min-microvolt = <3240306>; + regulator-max-microvolt = <3240306>; + lltc,fb-voltage-divider = <102000 29400>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ldo2 { + regulator-min-microvolt = <2484708>; + regulator-max-microvolt = <2484708>; + lltc,fb-voltage-divider = <100000 41200>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; + + touchscreen@49 { /* TSC2004 */ + compatible = "ti,tsc2004"; + reg = <0x49>; + vio-supply = <®_3p3v>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc2004_hw300>; + interrupts-extended = <&gpio4 14 IRQ_TYPE_EDGE_FALLING>; + status = "disabled"; + }; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + + rtc@56 { + compatible = "rv3029c2"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc_hw300>; + reg = <0x56>; + interrupt-parent = <&gpio7>; + interrupts = <12 2>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog_base>; + + pinctrl_hog_base: hog-base-grp { + fsl,pins = < + MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x120b0 + MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x120b0 + MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x120b0 + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x120b0 + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x120b0 + >; + }; + + pinctrl_ecspi1: ecspi1-grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 + MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0 + >; + }; + + pinctrl_ecspi2: ecspi2-grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO 0x100b1 + MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI 0x100b1 + MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK 0x100b1 + MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x1b0b0 + >; + }; + + pinctrl_enet_100M: enet-100M-grp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0 + MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0 + MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x000b0 + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b1 + MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x120b0 + >; + }; + + pinctrl_flexcan1: flexcan1-grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b0 + MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0 + >; + }; + + pinctrl_flexcan2: flexcan2-grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX 0x1b0b0 + MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1-grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2-grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3-grp { + fsl,pins = < + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_pmic_hw300: pmic-hw300-grp { + fsl,pins = < + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1B0B0 + >; + }; + + pinctrl_rtc_hw300: rtc-hw300-grp { + fsl,pins = < + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x120B0 + >; + }; + + pinctrl_tsc2004_hw300: tsc2004-hw300-grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x120B0 + >; + }; + + pinctrl_uart1: uart1-grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D20__UART1_RTS_B 0x1b0b1 + MX6QDL_PAD_EIM_D19__UART1_CTS_B 0x4001b0b1 + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x4001b0b1 + MX6QDL_PAD_EIM_D24__GPIO3_IO24 0x4001b0b1 + MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x4001b0b1 + MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x4001b0b1 + >; + }; + + pinctrl_uart4: uart4-grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5-grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT18__UART5_RTS_B 0x1b0b1 + MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B 0x4001b0b1 + >; + }; + + pinctrl_usbh1: usbh1-grp { + fsl,pins = < + MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x120B0 + >; + }; + + pinctrl_usbotg: usbotg-grp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc2: usdhc2-grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 + MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x120B0 + >; + }; + + pinctrl_usdhc3: usdhc3-grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x120B0 + >; + }; + + pinctrl_usdhc4: usdhc4-grp { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059 + >; + }; +}; + +®_arm { + vin-supply = <&sw3_reg>; +}; + +®_soc { + vin-supply = <&sw1_reg>; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + uart-has-rtscts; + dtr-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>; + dsr-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>; + rng-gpios = <&gpio2 31 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + uart-has-rtscts; + status = "okay"; +}; + +&usbh1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1>; + vbus-supply = <®_usb_h1_vbus>; + dr_mode = "host"; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + dr_mode = "otg"; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + cd-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>; + keep-power-in-suspend; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>; + fsl,wp-controller; + keep-power-in-suspend; + status = "disabled"; +}; + +&usdhc4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc4>; + non-removable; + bus-width = <8>; + no-1-8-v; + keep-power-in-suspend; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-gk802.dts b/arch/arm/boot/dts/imx6q-gk802.dts index 0be375611382..84d3540b3a97 100644 --- a/arch/arm/boot/dts/imx6q-gk802.dts +++ b/arch/arm/boot/dts/imx6q-gk802.dts @@ -8,6 +8,7 @@ /dts-v1/; #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> #include "imx6q.dtsi" / { @@ -43,7 +44,7 @@ recovery-button { label = "recovery"; gpios = <&gpio3 16 1>; - linux,code = <0x198>; /* KEY_RESTART */ + linux,code = <KEY_RESTART>; wakeup-source; }; }; diff --git a/arch/arm/boot/dts/imx6q-icore-mipi.dts b/arch/arm/boot/dts/imx6q-icore-mipi.dts new file mode 100644 index 000000000000..acd3d33476d4 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-icore-mipi.dts @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2017 Engicam S.r.l. + * Copyright (C) 2017 Amarula Solutions B.V. + * Author: Jagan Teki <jagan@amarulasolutions.com> + */ + +/dts-v1/; + +#include "imx6q.dtsi" +#include "imx6qdl-icore.dtsi" + +/ { + model = "Engicam i.CoreM6 Quad/Dual MIPI Starter Kit"; + compatible = "engicam,imx6-icore", "fsl,imx6q"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c2>; + status = "okay"; +}; + +&usdhc3 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-icore-ofcap12.dts b/arch/arm/boot/dts/imx6q-icore-ofcap12.dts index 9e230f56c5fb..6e27c8143f82 100644 --- a/arch/arm/boot/dts/imx6q-icore-ofcap12.dts +++ b/arch/arm/boot/dts/imx6q-icore-ofcap12.dts @@ -48,28 +48,31 @@ / { model = "Engicam i.CoreM6 Quad/Dual OpenFrame Capacitive touch 12 Kit"; compatible = "engicam,imx6-icore", "fsl,imx6q"; + + panel { + compatible = "koe,tx31d200vm0baa"; + backlight = <&backlight_lvds>; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; }; &ldb { status = "okay"; lvds-channel@0 { - fsl,data-mapping = "spwg"; - fsl,data-width = <18>; + reg = <0>; status = "okay"; - display-timings { - native-mode = <&timing0>; - timing0: timing0 { - clock-frequency = <46800000>; - hactive = <1280>; - vactive = <480>; - hback-porch = <353>; - hfront-porch = <47>; - vback-porch = <39>; - vfront-porch = <4>; - hsync-len = <8>; - vsync-len = <2>; + port@4 { + reg = <4>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; }; }; }; diff --git a/arch/arm/boot/dts/imx6q-kp-tpc.dts b/arch/arm/boot/dts/imx6q-kp-tpc.dts new file mode 100644 index 000000000000..302d8d06e4cc --- /dev/null +++ b/arch/arm/boot/dts/imx6q-kp-tpc.dts @@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2018 + * Lukasz Majewski, DENX Software Engineering, lukma@denx.de + */ + +/dts-v1/; + +#include "imx6q-kp.dtsi" + +/ { + model = "Freescale i.MX6 Qwuad K+P TPC Board"; + compatible = "kiebackpeter,imx6q-tpc", "fsl,imx6q"; + + memory@10000000 { + reg = <0x10000000 0x40000000>; + }; +}; + +&ipu1_di0_disp0 { + remote-endpoint = <&lcd_display_in>; +}; diff --git a/arch/arm/boot/dts/imx6q-kp.dtsi b/arch/arm/boot/dts/imx6q-kp.dtsi new file mode 100644 index 000000000000..24c8169baf44 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-kp.dtsi @@ -0,0 +1,432 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2018 + * Lukasz Majewski, DENX Software Engineering, lukma@denx.de + */ + +/dts-v1/; + +#include "imx6q.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pwm/pwm.h> +#include <dt-bindings/sound/fsl-imx-audmux.h> + +/ { + backlight_lcd: backlight-lcd { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000>; + brightness-levels = <0 255>; + num-interpolated-steps = <255>; + default-brightness-level = <250>; + }; + + beeper { + compatible = "pwm-beeper"; + pwms = <&pwm2 0 500000>; + }; + + lcd_display: display { + compatible = "fsl,imx-parallel-display"; + #address-cells = <1>; + #size-cells = <0>; + interface-pix-fmt = "rgb24"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ipu1>; + + port@0 { + reg = <0>; + + lcd_display_in: endpoint { + remote-endpoint = <&ipu1_di0_disp0>; + }; + }; + + port@1 { + reg = <1>; + + lcd_display_out: endpoint { + remote-endpoint = <&lcd_panel_in>; + }; + }; + }; + + lcd_panel: lcd-panel { + compatible = "auo,g070vvn01"; + backlight = <&backlight_lcd>; + power-supply = <®_display>; + + port { + lcd_panel_in: endpoint { + remote-endpoint = <&lcd_display_out>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + green { + label = "led1"; + gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "gpio"; + default-state = "off"; + }; + + red { + label = "led0"; + gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "gpio"; + default-state = "off"; + }; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_audio: regulator-audio { + compatible = "regulator-fixed"; + regulator-name = "sgtl5000-supply"; + gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + reg_display: regulator-display { + compatible = "regulator-fixed"; + regulator-name = "display-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_h1_vbus: regulator-usb_h1_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_h1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "imx6q-sgtl5000-audio"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&codec_dai>; + simple-audio-card,frame-master = <&codec_dai>; + + cpu_dai: simple-audio-card,cpu { + sound-dai = <&ssi1>; + }; + + codec_dai: simple-audio-card,codec { + sound-dai = <&sgtl5000>; + }; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; + + ssi1 { + fsl,audmux-port = <0>; + fsl,port-config = < + (IMX_AUDMUX_V2_PTCR_SYN | + IMX_AUDMUX_V2_PTCR_TFSEL(2) | + IMX_AUDMUX_V2_PTCR_TCSEL(2) | + IMX_AUDMUX_V2_PTCR_TFSDIR | + IMX_AUDMUX_V2_PTCR_TCLKDIR) + IMX_AUDMUX_V2_PDCR_RXDSEL(2) + >; + }; + + aud3 { + fsl,audmux-port = <2>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN + IMX_AUDMUX_V2_PDCR_RXDSEL(0) + >; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + fsl,magic-packet; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + touchscreen@5d { + compatible = "goodix,gt911"; + reg = <0x5d>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ts>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + irq-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>; + }; + + ds1307: rtc@32 { + compatible = "dallas,ds1307"; + reg = <0x32>; + }; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + sgtl5000: audio-codec@a { + compatible = "fsl,sgtl5000"; + #sound-dai-cells = <0>; + reg = <0x0a>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_codec>; + clocks = <&clks IMX6QDL_CLK_CKO>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; + }; +}; + +&iomuxc { + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_codec: codecgrp { + fsl,pins = < + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b0 + /* sgtl5000 sys_mclk clock routed to CLKO1 */ + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000b0 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_flexcan1: can1grp { + fsl,pins = < + MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0 + MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0 + >; + }; + + pinctrl_flexcan2: can2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b0b0 + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1 + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_ipu1: ipu1grp { + fsl,pins = < + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10 + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10 + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10 + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10 + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10 + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10 + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10 + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10 + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10 + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10 + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10 + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10 + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10 + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10 + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10 + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10 + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10 + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10 + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10 + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10 + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10 + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10 + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10 + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10 + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10 + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10 + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1 + >; + }; + + pinctrl_ts: tsgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D28__UART2_CTS_B 0x1b0b1 + MX6QDL_PAD_EIM_D29__UART2_RTS_B 0x1b0b1 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc4: usdhc4grp { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059 + >; + }; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; + status = "okay"; +}; + +&ssi1 { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + uart-has-rtscts; +}; + +&usbh1 { + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + bus-width = <4>; + cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&usdhc4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc4>; + bus-width = <8>; + non-removable; + no-1-8-v; + keep-power-in-suspend; + status = "okay"; +}; + +&wdog1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-novena.dts b/arch/arm/boot/dts/imx6q-novena.dts index 52f39371188d..fcd824dc485b 100644 --- a/arch/arm/boot/dts/imx6q-novena.dts +++ b/arch/arm/boot/dts/imx6q-novena.dts @@ -268,8 +268,6 @@ touch: stmpe811@44 { compatible = "st,stmpe811"; reg = <0x44>; - #address-cells = <1>; - #size-cells = <0>; irq-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; id = <0>; blocks = <0x5>; diff --git a/arch/arm/boot/dts/imx6q-pistachio.dts b/arch/arm/boot/dts/imx6q-pistachio.dts index bd57b3b74db7..a31e83cd07a3 100644 --- a/arch/arm/boot/dts/imx6q-pistachio.dts +++ b/arch/arm/boot/dts/imx6q-pistachio.dts @@ -614,7 +614,7 @@ &uart5 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart5>; - fsl,uart-has-rtscts; + uart-has-rtscts; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6q-sabreauto.dts b/arch/arm/boot/dts/imx6q-sabreauto.dts index 334b9247e78c..6e981a3e0a83 100644 --- a/arch/arm/boot/dts/imx6q-sabreauto.dts +++ b/arch/arm/boot/dts/imx6q-sabreauto.dts @@ -1,14 +1,7 @@ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Freescale Semiconductor, Inc. +// Copyright 2011 Linaro Ltd. /dts-v1/; diff --git a/arch/arm/boot/dts/imx6q-sabresd.dts b/arch/arm/boot/dts/imx6q-sabresd.dts index 527772b62fee..eec944673c0b 100644 --- a/arch/arm/boot/dts/imx6q-sabresd.dts +++ b/arch/arm/boot/dts/imx6q-sabresd.dts @@ -1,14 +1,7 @@ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Freescale Semiconductor, Inc. +// Copyright 2011 Linaro Ltd. /dts-v1/; diff --git a/arch/arm/boot/dts/imx6q-udoo.dts b/arch/arm/boot/dts/imx6q-udoo.dts index c3e64ff3d544..52e9f4a211d0 100644 --- a/arch/arm/boot/dts/imx6q-udoo.dts +++ b/arch/arm/boot/dts/imx6q-udoo.dts @@ -1,12 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright 2013 Freescale Semiconductor, Inc. * * Author: Fabio Estevam <fabio.estevam@freescale.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * */ /dts-v1/; #include "imx6q.dtsi" diff --git a/arch/arm/boot/dts/imx6q-utilite-pro.dts b/arch/arm/boot/dts/imx6q-utilite-pro.dts index f5d9c34b0d39..d16ff2083d62 100644 --- a/arch/arm/boot/dts/imx6q-utilite-pro.dts +++ b/arch/arm/boot/dts/imx6q-utilite-pro.dts @@ -61,8 +61,6 @@ encoder { compatible = "ti,tfp410"; - #address-cells = <1>; - #size-cells = <0>; ports { #address-cells = <1>; diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts index e0728d475f6f..f2368a073d07 100644 --- a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts +++ b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts @@ -26,8 +26,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; autorepeat; back { diff --git a/arch/arm/boot/dts/imx6q-wandboard-revb1.dts b/arch/arm/boot/dts/imx6q-wandboard-revb1.dts index b763352cddae..be85b980bdfe 100644 --- a/arch/arm/boot/dts/imx6q-wandboard-revb1.dts +++ b/arch/arm/boot/dts/imx6q-wandboard-revb1.dts @@ -1,12 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright 2013 Freescale Semiconductor, Inc. * * Author: Fabio Estevam <fabio.estevam@freescale.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * */ /dts-v1/; #include "imx6q.dtsi" diff --git a/arch/arm/boot/dts/imx6q-wandboard-revd1.dts b/arch/arm/boot/dts/imx6q-wandboard-revd1.dts index 8691fab21058..fcfba28764d4 100644 --- a/arch/arm/boot/dts/imx6q-wandboard-revd1.dts +++ b/arch/arm/boot/dts/imx6q-wandboard-revd1.dts @@ -1,12 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright 2013 Freescale Semiconductor, Inc. * * Author: Fabio Estevam <fabio.estevam@freescale.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * */ /dts-v1/; #include "imx6q.dtsi" diff --git a/arch/arm/boot/dts/imx6q-wandboard.dts b/arch/arm/boot/dts/imx6q-wandboard.dts index 2a3d98c1489a..fa36fe183fc0 100644 --- a/arch/arm/boot/dts/imx6q-wandboard.dts +++ b/arch/arm/boot/dts/imx6q-wandboard.dts @@ -1,12 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright 2013 Freescale Semiconductor, Inc. * * Author: Fabio Estevam <fabio.estevam@freescale.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * */ /dts-v1/; #include "imx6q.dtsi" diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi index ae7b3f107893..70483ce72ba6 100644 --- a/arch/arm/boot/dts/imx6q.dtsi +++ b/arch/arm/boot/dts/imx6q.dtsi @@ -1,12 +1,6 @@ - -/* - * Copyright 2013 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - */ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright 2013 Freescale Semiconductor, Inc. #include <dt-bindings/interrupt-controller/irq.h> #include "imx6q-pinfunc.h" @@ -162,22 +156,27 @@ #size-cells = <0>; reg = <2>; - ipu2_di0_disp0: disp0-endpoint { + ipu2_di0_disp0: endpoint@0 { + reg = <0>; }; - ipu2_di0_hdmi: hdmi-endpoint { + ipu2_di0_hdmi: endpoint@1 { + reg = <1>; remote-endpoint = <&hdmi_mux_2>; }; - ipu2_di0_mipi: mipi-endpoint { + ipu2_di0_mipi: endpoint@2 { + reg = <2>; remote-endpoint = <&mipi_mux_2>; }; - ipu2_di0_lvds0: lvds0-endpoint { + ipu2_di0_lvds0: endpoint@3 { + reg = <3>; remote-endpoint = <&lvds0_mux_2>; }; - ipu2_di0_lvds1: lvds1-endpoint { + ipu2_di0_lvds1: endpoint@4 { + reg = <4>; remote-endpoint = <&lvds1_mux_2>; }; }; @@ -187,19 +186,23 @@ #size-cells = <0>; reg = <3>; - ipu2_di1_hdmi: hdmi-endpoint { + ipu2_di1_hdmi: endpoint@1 { + reg = <1>; remote-endpoint = <&hdmi_mux_3>; }; - ipu2_di1_mipi: mipi-endpoint { + ipu2_di1_mipi: endpoint@2 { + reg = <2>; remote-endpoint = <&mipi_mux_3>; }; - ipu2_di1_lvds0: lvds0-endpoint { + ipu2_di1_lvds0: endpoint@3 { + reg = <3>; remote-endpoint = <&lvds0_mux_3>; }; - ipu2_di1_lvds1: lvds1-endpoint { + ipu2_di1_lvds1: endpoint@4 { + reg = <4>; remote-endpoint = <&lvds1_mux_3>; }; }; diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi b/arch/arm/boot/dts/imx6qdl-apalis.dtsi index 8206683172d2..64fbee61de44 100644 --- a/arch/arm/boot/dts/imx6qdl-apalis.dtsi +++ b/arch/arm/boot/dts/imx6qdl-apalis.dtsi @@ -331,8 +331,6 @@ compatible = "st,stmpe811"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_touch_int>; - #address-cells = <1>; - #size-cells = <0>; reg = <0x41>; interrupts = <10 IRQ_TYPE_LEVEL_LOW>; interrupt-parent = <&gpio4>; diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi index e4eb300549d4..76035db96f67 100644 --- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi +++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi @@ -262,8 +262,6 @@ compatible = "st,stmpe811"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_touch_int>; - #address-cells = <1>; - #size-cells = <0>; reg = <0x41>; interrupts = <20 IRQ_TYPE_LEVEL_LOW>; interrupt-parent = <&gpio6>; diff --git a/arch/arm/boot/dts/imx6qdl-gw5904.dtsi b/arch/arm/boot/dts/imx6qdl-gw5904.dtsi index 58124adfd65b..3c52bdb453f3 100644 --- a/arch/arm/boot/dts/imx6qdl-gw5904.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw5904.dtsi @@ -162,8 +162,6 @@ switch@0 { compatible = "marvell,mv88e6085"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; ports { diff --git a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi b/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi index 7e20b47de839..0e64016e765f 100644 --- a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi +++ b/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi @@ -38,6 +38,7 @@ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR * OTHER DEALINGS IN THE SOFTWARE. */ +#include <dt-bindings/sound/fsl-imx-audmux.h> / { /* Will be filled by the bootloader */ @@ -110,17 +111,27 @@ vin-supply = <&v_5v0>; }; - sound-sgtl5000 { - audio-codec = <&sgtl5000>; - audio-routing = - "MIC_IN", "Mic Jack", - "Mic Jack", "Mic Bias", + audio: sound-sgtl5000 { + compatible = "simple-audio-card"; + simple-audio-card,name = "On-board Codec"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&sound_codec>; + simple-audio-card,frame-master = <&sound_codec>; + simple-audio-card,widgets = + "Microphone", "Headphone Jack", + "Headphone", "Headphone Jack"; + simple-audio-card,routing = + "MIC_IN", "Headphone Jack", + "Headphone Jack", "Mic Bias", "Headphone Jack", "HP_OUT"; - compatible = "fsl,imx-audio-sgtl5000"; - model = "On-board Codec"; - mux-ext-port = <5>; - mux-int-port = <1>; - ssi-controller = <&ssi1>; + + sound_cpu: simple-audio-card,cpu { + sound-dai = <&ssi1>; + }; + + sound_codec: simple-audio-card,codec { + sound-dai = <&sgtl5000>; + }; }; sound-spdif { @@ -134,6 +145,26 @@ &audmux { status = "okay"; + + ssi1 { + fsl,audmux-port = <0>; + fsl,port-config = < + (IMX_AUDMUX_V2_PTCR_SYN | + IMX_AUDMUX_V2_PTCR_TFSEL(4) | + IMX_AUDMUX_V2_PTCR_TCSEL(4) | + IMX_AUDMUX_V2_PTCR_TFSDIR | + IMX_AUDMUX_V2_PTCR_TCLKDIR) + IMX_AUDMUX_V2_PDCR_RXDSEL(4) + >; + }; + + pins5 { + fsl,audmux-port = <4>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN + IMX_AUDMUX_V2_PDCR_RXDSEL(0) + >; + }; }; &can1 { @@ -166,6 +197,7 @@ compatible = "fsl,sgtl5000"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hummingboard_sgtl5000>; + #sound-dai-cells = <0>; reg = <0x0a>; VDDA-supply = <&v_3v2>; VDDIO-supply = <&v_3v2>; diff --git a/arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi b/arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi index 98241acb08a6..c413f9c3540f 100644 --- a/arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi +++ b/arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi @@ -38,6 +38,7 @@ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR * OTHER DEALINGS IN THE SOFTWARE. */ +#include <dt-bindings/sound/fsl-imx-audmux.h> / { /* Will be filled by the bootloader */ @@ -150,22 +151,52 @@ vin-supply = <&v_5v0>; }; - sound-sgtl5000 { - audio-codec = <&sgtl5000>; - audio-routing = + audio: sound-sgtl5000 { + compatible = "simple-audio-card"; + simple-audio-card,name = "On-board Codec"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&sound_codec>; + simple-audio-card,frame-master = <&sound_codec>; + simple-audio-card,widgets = + "Microphone", "Mic Jack", + "Headphone", "Headphone Jack"; + simple-audio-card,routing = "MIC_IN", "Mic Jack", "Mic Jack", "Mic Bias", "Headphone Jack", "HP_OUT"; - compatible = "fsl,imx-audio-sgtl5000"; - model = "On-board Codec"; - mux-ext-port = <5>; - mux-int-port = <1>; - ssi-controller = <&ssi1>; + + sound_cpu: simple-audio-card,cpu { + sound-dai = <&ssi1>; + }; + + sound_codec: simple-audio-card,codec { + sound-dai = <&sgtl5000>; + }; }; }; &audmux { status = "okay"; + + ssi1 { + fsl,audmux-port = <0>; + fsl,port-config = < + (IMX_AUDMUX_V2_PTCR_SYN | + IMX_AUDMUX_V2_PTCR_TFSEL(4) | + IMX_AUDMUX_V2_PTCR_TCSEL(4) | + IMX_AUDMUX_V2_PTCR_TFSDIR | + IMX_AUDMUX_V2_PTCR_TCLKDIR) + IMX_AUDMUX_V2_PDCR_RXDSEL(4) + >; + }; + + pins5 { + fsl,audmux-port = <4>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN + IMX_AUDMUX_V2_PDCR_RXDSEL(0) + >; + }; }; &ecspi2 { diff --git a/arch/arm/boot/dts/imx6qdl-icore.dtsi b/arch/arm/boot/dts/imx6qdl-icore.dtsi index b3a463a5908b..0a1574998fc6 100644 --- a/arch/arm/boot/dts/imx6qdl-icore.dtsi +++ b/arch/arm/boot/dts/imx6qdl-icore.dtsi @@ -49,7 +49,7 @@ reg = <0x10000000 0x80000000>; }; - backlight { + backlight_lvds: backlight-lvds { compatible = "pwm-backlight"; pwms = <&pwm3 0 100000>; brightness-levels = <0 4 8 16 32 64 128 255>; @@ -265,6 +265,14 @@ status = "okay"; }; +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + no-1-8-v; + non-removable; + status = "disabled"; +}; + &iomuxc { pinctrl_audmux: audmux { fsl,pins = < @@ -378,4 +386,19 @@ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17070 >; }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059 + >; + }; }; diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi index c58f3443d55d..ed1aafd56973 100644 --- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi +++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi @@ -115,7 +115,7 @@ compatible = "dlg,da9063"; reg = <0x58>; interrupt-parent = <&gpio2>; - interrupts = <9 0x8>; /* active-low GPIO2_9 */ + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; /* active-low GPIO2_9 */ regulators { vddcore_reg: bcore1 { diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi index 54b0139e978d..0e28e36ddbb2 100644 --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi @@ -1,14 +1,7 @@ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Freescale Semiconductor, Inc. +// Copyright 2011 Linaro Ltd. #include <dt-bindings/gpio/gpio.h> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi index 18b65052553d..654cf2c9b073 100644 --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi @@ -379,9 +379,6 @@ powerdown-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* NANDF_WP_B */ port { - #address-cells = <1>; - #size-cells = <0>; - ov5640_to_mipi_csi2: endpoint { remote-endpoint = <&mipi_csi2_in>; clock-lanes = <0>; diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi index f019f9900369..15744ad52535 100644 --- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi @@ -1,14 +1,7 @@ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Freescale Semiconductor, Inc. +// Copyright 2011 Linaro Ltd. #include <dt-bindings/clock/imx6qdl-clock.h> #include <dt-bindings/gpio/gpio.h> @@ -294,9 +287,6 @@ reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; port { - #address-cells = <1>; - #size-cells = <0>; - ov5640_to_mipi_csi2: endpoint { remote-endpoint = <&mipi_csi2_in>; clock-lanes = <0>; diff --git a/arch/arm/boot/dts/imx6qdl-tx6-lcd.dtsi b/arch/arm/boot/dts/imx6qdl-tx6-lcd.dtsi index 5102fc47380b..79f2354886b7 100644 --- a/arch/arm/boot/dts/imx6qdl-tx6-lcd.dtsi +++ b/arch/arm/boot/dts/imx6qdl-tx6-lcd.dtsi @@ -77,7 +77,6 @@ enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>; power-supply = <®_3v3>; backlight = <&backlight>; - bus-format-override = "rgb24"; port { lcd_panel_in: endpoint { diff --git a/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi b/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi index 4c4e2e1a931f..410972e1dca9 100644 --- a/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi +++ b/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi @@ -54,19 +54,16 @@ lcd-panel { compatible = "edt,et057090dhu"; - bus-format-override = "rgb24"; pixelclk-active = <0>; }; lvds0-panel { compatible = "edt,etml1010g0dka"; - bus-format-override = "spwg-18"; pixelclk-active = <0>; }; lvds1-panel { compatible = "edt,etml1010g0dka"; - bus-format-override = "spwg-18"; pixelclk-active = <0>; }; }; diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi index f015e2d1cf35..a98fb2564c63 100644 --- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi +++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi @@ -50,11 +50,11 @@ can0 = &can2; can1 = &can1; ethernet0 = &fec; - lcdif_23bit_pins_a = &pinctrl_disp0_1; - lcdif_24bit_pins_a = &pinctrl_disp0_2; + lcdif-23bit-pins-a = &pinctrl_disp0_1; + lcdif-24bit-pins-a = &pinctrl_disp0_2; pwm0 = &pwm1; pwm1 = &pwm2; - reg_can_xcvr = ®_can_xcvr; + reg-can-xcvr = ®_can_xcvr; stk5led = &user_led; usbotg = &usbotg; sdhc0 = &usdhc1; diff --git a/arch/arm/boot/dts/imx6qdl-udoo.dtsi b/arch/arm/boot/dts/imx6qdl-udoo.dtsi index 906387915dc5..4f27861bbb32 100644 --- a/arch/arm/boot/dts/imx6qdl-udoo.dtsi +++ b/arch/arm/boot/dts/imx6qdl-udoo.dtsi @@ -1,12 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright 2013 Freescale Semiconductor, Inc. * * Author: Fabio Estevam <fabio.estevam@freescale.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * */ / { diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi index a32089132263..855dc6f9df75 100644 --- a/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi +++ b/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi @@ -17,7 +17,6 @@ imx6qdl-wandboard { pinctrl_hog: hoggrp { fsl,pins = < - MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 /* GPIO_0_CLKO */ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000 /* uSDHC1 CD */ MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x80000000 /* uSDHC3 CD */ MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x0f0b0 /* WL_REF_ON */ diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi index 8d893a78cdf0..49a0a557e62e 100644 --- a/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi +++ b/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi @@ -17,7 +17,6 @@ imx6qdl-wandboard { pinctrl_hog: hoggrp { fsl,pins = < - MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 /* GPIO_0_CLKO */ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000 /* uSDHC1 CD */ MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x80000000 /* uSDHC3 CD */ MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00 0x0f0b0 /* WIFI_ON (reset, active low) */ diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi index 3a8a4952d45e..69d9c8661439 100644 --- a/arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi +++ b/arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi @@ -147,7 +147,6 @@ imx6qdl-wandboard { pinctrl_hog: hoggrp { fsl,pins = < - MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 MX6QDL_PAD_EIM_D22__USB_OTG_PWR 0x80000000 /* USB Power Enable */ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000 /* USDHC1 CD */ MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x80000000 /* uSDHC3 CD */ diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi index ed96d7b5feab..e1afa54404d0 100644 --- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi +++ b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi @@ -1,12 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright 2013 Freescale Semiconductor, Inc. * * Author: Fabio Estevam <fabio.estevam@freescale.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * */ #include <dt-bindings/gpio/gpio.h> @@ -83,6 +79,8 @@ status = "okay"; codec: sgtl5000@a { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mclk>; compatible = "fsl,sgtl5000"; reg = <0x0a>; clocks = <&clks IMX6QDL_CLK_CKO>; @@ -142,6 +140,12 @@ >; }; + pinctrl_mclk: mclkgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 + >; + }; + pinctrl_spdif: spdifgrp { fsl,pins = < MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1b0b0 diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi index 911f7f0e3cea..19a075aee19e 100644 --- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi +++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi @@ -263,6 +263,17 @@ }; }; +&cpu0 { + fsl,soc-operating-points = < + /* ARM kHz SOC-PU uV */ + 1200000 1300000 + 996000 1275000 + 852000 1275000 + 792000 1200000 + 396000 1200000 + >; +}; + ®_arm { vin-supply = <&sw1a_reg>; }; @@ -571,6 +582,17 @@ }; }; + touchscreen@2a { + compatible = "eeti,egalax_ts"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ts>; + reg = <0x2a>; + interrupt-parent = <&gpio1>; + interrupts = <8 IRQ_TYPE_LEVEL_LOW>; + wakeup-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + status = "disabled"; + }; + hpa1: amp@60 { compatible = "ti,tpa6130a2"; pinctrl-names = "default"; @@ -666,8 +688,6 @@ compatible = "marvell,mv88e6085"; pinctrl-0 = <&pinctrl_switch_irq>; pinctrl-names = "default"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; dsa,member = <0 0>; eeprom-length = <512>; diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index c003e62bf290..911141e24681 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -1,14 +1,7 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2011 Freescale Semiconductor, Inc. +// Copyright 2011 Linaro Ltd. #include <dt-bindings/clock/imx6qdl-clock.h> #include <dt-bindings/interrupt-controller/arm-gic.h> @@ -58,9 +51,6 @@ }; clocks { - #address-cells = <1>; - #size-cells = <0>; - ckil { compatible = "fsl,imx-ckil", "fixed-clock"; #clock-cells = <0>; @@ -695,11 +685,8 @@ interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>, <0 54 IRQ_TYPE_LEVEL_HIGH>, <0 127 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - regulator-1p1@20c8110 { - reg = <0x20c8110>; + regulator-1p1 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd1p1"; regulator-min-microvolt = <1000000>; @@ -714,8 +701,7 @@ anatop-enable-bit = <0>; }; - regulator-3p0@20c8120 { - reg = <0x20c8120>; + regulator-3p0 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd3p0"; regulator-min-microvolt = <2800000>; @@ -730,8 +716,7 @@ anatop-enable-bit = <0>; }; - regulator-2p5@20c8130 { - reg = <0x20c8130>; + regulator-2p5 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd2p5"; regulator-min-microvolt = <2250000>; @@ -746,8 +731,7 @@ anatop-enable-bit = <0>; }; - reg_arm: regulator-vddcore@20c8140 { - reg = <0x20c8140>; + reg_arm: regulator-vddcore { compatible = "fsl,anatop-regulator"; regulator-name = "vddarm"; regulator-min-microvolt = <725000>; @@ -764,8 +748,7 @@ anatop-max-voltage = <1450000>; }; - reg_pu: regulator-vddpu@20c8140 { - reg = <0x20c8140>; + reg_pu: regulator-vddpu { compatible = "fsl,anatop-regulator"; regulator-name = "vddpu"; regulator-min-microvolt = <725000>; @@ -782,8 +765,7 @@ anatop-max-voltage = <1450000>; }; - reg_soc: regulator-vddsoc@20c8140 { - reg = <0x20c8140>; + reg_soc: regulator-vddsoc { compatible = "fsl,anatop-regulator"; regulator-name = "vddsoc"; regulator-min-microvolt = <725000>; @@ -1187,8 +1169,6 @@ }; mipi_dsi: mipi@21e0000 { - #address-cells = <1>; - #size-cells = <0>; reg = <0x021e0000 0x4000>; status = "disabled"; @@ -1300,22 +1280,27 @@ #size-cells = <0>; reg = <2>; - ipu1_di0_disp0: disp0-endpoint { + ipu1_di0_disp0: endpoint@0 { + reg = <0>; }; - ipu1_di0_hdmi: hdmi-endpoint { + ipu1_di0_hdmi: endpoint@1 { + reg = <1>; remote-endpoint = <&hdmi_mux_0>; }; - ipu1_di0_mipi: mipi-endpoint { + ipu1_di0_mipi: endpoint@2 { + reg = <2>; remote-endpoint = <&mipi_mux_0>; }; - ipu1_di0_lvds0: lvds0-endpoint { + ipu1_di0_lvds0: endpoint@3 { + reg = <3>; remote-endpoint = <&lvds0_mux_0>; }; - ipu1_di0_lvds1: lvds1-endpoint { + ipu1_di0_lvds1: endpoint@4 { + reg = <4>; remote-endpoint = <&lvds1_mux_0>; }; }; @@ -1325,22 +1310,27 @@ #size-cells = <0>; reg = <3>; - ipu1_di1_disp1: disp1-endpoint { + ipu1_di1_disp1: endpoint@0 { + reg = <0>; }; - ipu1_di1_hdmi: hdmi-endpoint { + ipu1_di1_hdmi: endpoint@1 { + reg = <1>; remote-endpoint = <&hdmi_mux_1>; }; - ipu1_di1_mipi: mipi-endpoint { + ipu1_di1_mipi: endpoint@2 { + reg = <2>; remote-endpoint = <&mipi_mux_1>; }; - ipu1_di1_lvds0: lvds0-endpoint { + ipu1_di1_lvds0: endpoint@3 { + reg = <3>; remote-endpoint = <&lvds0_mux_1>; }; - ipu1_di1_lvds1: lvds1-endpoint { + ipu1_di1_lvds1: endpoint@4 { + reg = <4>; remote-endpoint = <&lvds1_mux_1>; }; }; diff --git a/arch/arm/boot/dts/imx6qp-sabreauto.dts b/arch/arm/boot/dts/imx6qp-sabreauto.dts index 5ce3840d83d3..d4caeeb0af70 100644 --- a/arch/arm/boot/dts/imx6qp-sabreauto.dts +++ b/arch/arm/boot/dts/imx6qp-sabreauto.dts @@ -1,44 +1,6 @@ -/* - * Copyright 2016 Freescale Semiconductor, Inc. - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +// +// Copyright 2016 Freescale Semiconductor, Inc. /dts-v1/; diff --git a/arch/arm/boot/dts/imx6qp-sabresd.dts b/arch/arm/boot/dts/imx6qp-sabresd.dts index a8a5004dd9c8..f1b9cb104fdd 100644 --- a/arch/arm/boot/dts/imx6qp-sabresd.dts +++ b/arch/arm/boot/dts/imx6qp-sabresd.dts @@ -1,44 +1,6 @@ -/* - * Copyright 2016 Freescale Semiconductor, Inc. - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +// +// Copyright 2016 Freescale Semiconductor, Inc. /dts-v1/; diff --git a/arch/arm/boot/dts/imx6qp-wandboard-revd1.dts b/arch/arm/boot/dts/imx6qp-wandboard-revd1.dts index 907ba0c74ba6..bcca5ac5fa51 100644 --- a/arch/arm/boot/dts/imx6qp-wandboard-revd1.dts +++ b/arch/arm/boot/dts/imx6qp-wandboard-revd1.dts @@ -1,12 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright 2013 Freescale Semiconductor, Inc. * * Author: Fabio Estevam <fabio.estevam@freescale.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * */ /dts-v1/; #include "imx6qp.dtsi" diff --git a/arch/arm/boot/dts/imx6qp-zii-rdu2.dts b/arch/arm/boot/dts/imx6qp-zii-rdu2.dts index de5b50df833c..8c293e9f36a7 100644 --- a/arch/arm/boot/dts/imx6qp-zii-rdu2.dts +++ b/arch/arm/boot/dts/imx6qp-zii-rdu2.dts @@ -53,3 +53,8 @@ reg = <0x10000000 0>; }; }; + +&gpu_3d { + assigned-clocks = <&clks IMX6QDL_CLK_GPU3D_SHADER_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL2_PFD1_594M>; +}; diff --git a/arch/arm/boot/dts/imx6qp.dtsi b/arch/arm/boot/dts/imx6qp.dtsi index 5f4fdce715c1..5f51f8e5c1fa 100644 --- a/arch/arm/boot/dts/imx6qp.dtsi +++ b/arch/arm/boot/dts/imx6qp.dtsi @@ -1,44 +1,6 @@ -/* - * Copyright 2016 Freescale Semiconductor, Inc. - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +// +// Copyright 2016 Freescale Semiconductor, Inc. #include "imx6q.dtsi" diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts index 37e792fdc160..92ad01f676e3 100644 --- a/arch/arm/boot/dts/imx6sl-evk.dts +++ b/arch/arm/boot/dts/imx6sl-evk.dts @@ -1,10 +1,6 @@ -/* - * Copyright (C) 2013 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ +// SPDX-License-Identifier: GPL-2.0 +// +//Copyright (C) 2013 Freescale Semiconductor, Inc. /dts-v1/; diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi index ab6a7e2e7e8f..994e48dc1df0 100644 --- a/arch/arm/boot/dts/imx6sl.dtsi +++ b/arch/arm/boot/dts/imx6sl.dtsi @@ -1,11 +1,6 @@ -/* - * Copyright 2013 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - */ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright 2013 Freescale Semiconductor, Inc. #include <dt-bindings/interrupt-controller/irq.h> #include "imx6sl-pinfunc.h" @@ -86,9 +81,6 @@ }; clocks { - #address-cells = <1>; - #size-cells = <0>; - ckil { compatible = "fixed-clock"; #clock-cells = <0>; @@ -527,11 +519,8 @@ interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>, <0 54 IRQ_TYPE_LEVEL_HIGH>, <0 127 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - regulator-1p1@20c8110 { - reg = <0x20c8110>; + regulator-1p1 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd1p1"; regulator-min-microvolt = <800000>; @@ -546,8 +535,7 @@ anatop-enable-bit = <0>; }; - regulator-3p0@20c8120 { - reg = <0x20c8120>; + regulator-3p0 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd3p0"; regulator-min-microvolt = <2800000>; @@ -562,8 +550,7 @@ anatop-enable-bit = <0>; }; - regulator-2p5@20c8130 { - reg = <0x20c8130>; + regulator-2p5 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd2p5"; regulator-min-microvolt = <2100000>; @@ -578,8 +565,7 @@ anatop-enable-bit = <0>; }; - reg_arm: regulator-vddcore@20c8140 { - reg = <0x20c8140>; + reg_arm: regulator-vddcore { compatible = "fsl,anatop-regulator"; regulator-name = "vddarm"; regulator-min-microvolt = <725000>; @@ -596,8 +582,7 @@ anatop-max-voltage = <1450000>; }; - reg_pu: regulator-vddpu@20c8140 { - reg = <0x20c8140>; + reg_pu: regulator-vddpu { compatible = "fsl,anatop-regulator"; regulator-name = "vddpu"; regulator-min-microvolt = <725000>; @@ -614,8 +599,7 @@ anatop-max-voltage = <1450000>; }; - reg_soc: regulator-vddsoc@20c8140 { - reg = <0x20c8140>; + reg_soc: regulator-vddsoc { compatible = "fsl,anatop-regulator"; regulator-name = "vddsoc"; regulator-min-microvolt = <725000>; diff --git a/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts b/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts index b58f770c40d9..59e52f504922 100644 --- a/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts +++ b/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts @@ -48,8 +48,8 @@ compatible = "boundary,imx6sx-nitrogen6sx", "fsl,imx6sx"; aliases { - fb_lcd = &lcdif1; - t_lcd = &t_lcd; + fb-lcd = &lcdif1; + t-lcd = &t_lcd; }; memory@80000000 { diff --git a/arch/arm/boot/dts/imx6sx-sabreauto.dts b/arch/arm/boot/dts/imx6sx-sabreauto.dts index 72da5acf35a2..841a27f3198f 100644 --- a/arch/arm/boot/dts/imx6sx-sabreauto.dts +++ b/arch/arm/boot/dts/imx6sx-sabreauto.dts @@ -1,10 +1,6 @@ -/* - * Copyright (C) 2014 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright (C) 2014 Freescale Semiconductor, Inc. /dts-v1/; @@ -18,25 +14,67 @@ reg = <0x80000000 0x80000000>; }; - regulators { - compatible = "simple-bus"; + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led>; + + user { + label = "debug"; + gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + vcc_sd3: regulator-vcc-sd3 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_vcc_sd3>; + regulator-name = "VCC_SD3"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&anaclk2 { + clock-frequency = <24576000>; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1>; + phy-mode = "rgmii"; + phy-handle = <ðphy1>; + fsl,magic-packet; + status = "okay"; + + mdio { #address-cells = <1>; #size-cells = <0>; - vcc_sd3: regulator@0 { - compatible = "regulator-fixed"; + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; reg = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_vcc_sd3>; - regulator-name = "VCC_SD3"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>; - enable-active-high; + }; + + ethphy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; }; }; }; +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2>; + phy-mode = "rgmii"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; +}; + &uart1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; @@ -69,78 +107,297 @@ }; &iomuxc { - imx6x-sabreauto { - pinctrl_uart1: uart1grp { - fsl,pins = < - MX6SX_PAD_GPIO1_IO04__UART1_TX 0x1b0b1 - MX6SX_PAD_GPIO1_IO05__UART1_RX 0x1b0b1 - >; - }; + pinctrl_egalax_int: egalax-intgrp { + fsl,pins = < + MX6SX_PAD_SD4_RESET_B__GPIO6_IO_22 0x10b0 + >; + }; - pinctrl_usdhc3: usdhc3grp { - fsl,pins = < - MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x17059 - MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x10059 - MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x17059 - MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x17059 - MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x17059 - MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x17059 - MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x17059 - MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x17059 - MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x17059 - MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x17059 - MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x17059 /* CD */ - MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x17059 /* WP */ - >; - }; + pinctrl_enet1: enet1grp { + fsl,pins = < + MX6SX_PAD_ENET1_MDIO__ENET1_MDIO 0xa0b1 + MX6SX_PAD_ENET1_MDC__ENET1_MDC 0xa0b1 + MX6SX_PAD_RGMII1_TXC__ENET1_RGMII_TXC 0xa0b9 + MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 0xa0b1 + MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 0xa0b1 + MX6SX_PAD_RGMII1_TD2__ENET1_TX_DATA_2 0xa0b1 + MX6SX_PAD_RGMII1_TD3__ENET1_TX_DATA_3 0xa0b1 + MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN 0xa0b1 + MX6SX_PAD_RGMII1_RXC__ENET1_RX_CLK 0x3081 + MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 0x3081 + MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 0x3081 + MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2 0x3081 + MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 0x3081 + MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x3081 + >; + }; - pinctrl_usdhc3_100mhz: usdhc3grp-100mhz { - fsl,pins = < - MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170b9 - MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100b9 - MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170b9 - MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170b9 - MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170b9 - MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170b9 - MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170b9 - MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170b9 - MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170b9 - MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170b9 - >; - }; + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC 0xa0b9 + MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 0xa0b1 + MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 0xa0b1 + MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2 0xa0b1 + MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3 0xa0b1 + MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN 0xa0b1 + MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK 0x3081 + MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 0x3081 + MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 0x3081 + MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2 0x3081 + MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3 0x3081 + MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN 0x3081 + >; + }; - pinctrl_usdhc3_200mhz: usdhc3grp-200mhz { - fsl,pins = < - MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170f9 - MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100f9 - MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170f9 - MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170f9 - MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170f9 - MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170f9 - MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170f9 - MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170f9 - MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170f9 - MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170f9 - >; - }; + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO03__I2C2_SDA 0x4001b8b1 + MX6SX_PAD_GPIO1_IO02__I2C2_SCL 0x4001b8b1 + >; + }; - pinctrl_usdhc4: usdhc4grp { - fsl,pins = < - MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059 - MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059 - MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059 - MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059 - MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059 - MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059 - MX6SX_PAD_SD4_DATA7__GPIO6_IO_21 0x17059 /* CD */ - MX6SX_PAD_SD4_DATA6__GPIO6_IO_20 0x17059 /* WP */ - >; - }; + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6SX_PAD_KEY_ROW4__I2C3_SDA 0x4001b8b1 + MX6SX_PAD_KEY_COL4__I2C3_SCL 0x4001b8b1 + >; + }; + + pinctrl_led: ledgrp { + fsl,pins = < + MX6SX_PAD_CSI_PIXCLK__GPIO1_IO_24 0x17059 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO04__UART1_TX 0x1b0b1 + MX6SX_PAD_GPIO1_IO05__UART1_RX 0x1b0b1 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x17059 + MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x10059 + MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x17059 + MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x17059 + MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x17059 + MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x17059 + MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x17059 + MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x17059 + MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x17059 + MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x17059 + MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x17059 /* CD */ + MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x17059 /* WP */ + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp-100mhz { + fsl,pins = < + MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170b9 + MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100b9 + MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170b9 + MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170b9 + MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170b9 + MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170b9 + MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170b9 + MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170b9 + MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170b9 + MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170b9 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp-200mhz { + fsl,pins = < + MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170f9 + MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100f9 + MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170f9 + MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170f9 + MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170f9 + MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170f9 + MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170f9 + MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170f9 + MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170f9 + MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170f9 + >; + }; + + pinctrl_usdhc4: usdhc4grp { + fsl,pins = < + MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059 + MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059 + MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059 + MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059 + MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059 + MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059 + MX6SX_PAD_SD4_DATA7__GPIO6_IO_21 0x17059 /* CD */ + MX6SX_PAD_SD4_DATA6__GPIO6_IO_20 0x17059 /* WP */ + >; + }; + + pinctrl_vcc_sd3: vccsd3grp { + fsl,pins = < + MX6SX_PAD_KEY_COL1__GPIO2_IO_11 0x17059 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO13__WDOG1_WDOG_ANY 0x30b0 + >; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + touchscreen@4 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_egalax_int>; + interrupt-parent = <&gpio6>; + interrupts = <22 IRQ_TYPE_EDGE_FALLING>; + wakeup-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; + }; + + pfuze100: pmic@8 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; - pinctrl_vcc_sd3: vccsd3grp { - fsl,pins = < - MX6SX_PAD_KEY_COL1__GPIO2_IO_11 0x17059 - >; + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + regulator-always-on; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; }; }; + + max7322: gpio@68 { + compatible = "maxim,max7322"; + reg = <0x68>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + max7310_a: gpio@30 { + compatible = "maxim,max7310"; + reg = <0x30>; + gpio-controller; + #gpio-cells = <2>; + }; + + max7310_b: gpio@32 { + compatible = "maxim,max7310"; + reg = <0x32>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; }; diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi index 49c7205b8db8..d8b94f47498b 100644 --- a/arch/arm/boot/dts/imx6sx.dtsi +++ b/arch/arm/boot/dts/imx6sx.dtsi @@ -1,10 +1,6 @@ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright 2014 Freescale Semiconductor, Inc. #include <dt-bindings/clock/imx6sx-clock.h> #include <dt-bindings/gpio/gpio.h> @@ -104,41 +100,46 @@ interrupt-parent = <&intc>; }; - clocks { - #address-cells = <1>; - #size-cells = <0>; + ckil: clock-ckil { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "ckil"; + }; - ckil: clock@0 { - compatible = "fixed-clock"; - reg = <0>; - #clock-cells = <0>; - clock-frequency = <32768>; - clock-output-names = "ckil"; - }; + osc: clock-osc { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + clock-output-names = "osc"; + }; - osc: clock@1 { - compatible = "fixed-clock"; - reg = <1>; - #clock-cells = <0>; - clock-frequency = <24000000>; - clock-output-names = "osc"; - }; + ipp_di0: clock-ipp-di0 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "ipp_di0"; + }; - ipp_di0: clock@2 { - compatible = "fixed-clock"; - reg = <2>; - #clock-cells = <0>; - clock-frequency = <0>; - clock-output-names = "ipp_di0"; - }; + ipp_di1: clock-ipp-di1 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "ipp_di1"; + }; - ipp_di1: clock@3 { - compatible = "fixed-clock"; - reg = <3>; - #clock-cells = <0>; - clock-frequency = <0>; - clock-output-names = "ipp_di1"; - }; + anaclk1: clock-anaclk1 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "anaclk1"; + }; + + anaclk2: clock-anaclk2 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "anaclk2"; }; tempmon: tempmon { @@ -575,8 +576,8 @@ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; #clock-cells = <1>; - clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>; - clock-names = "ckil", "osc", "ipp_di0", "ipp_di1"; + clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>, <&anaclk1>, <&anaclk2>; + clock-names = "ckil", "osc", "ipp_di0", "ipp_di1", "anaclk1", "anaclk2"; }; anatop: anatop@20c8000 { @@ -586,11 +587,8 @@ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - regulator-1p1@20c8110 { - reg = <0x20c8110>; + regulator-1p1 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd1p1"; regulator-min-microvolt = <800000>; @@ -605,8 +603,7 @@ anatop-enable-bit = <0>; }; - regulator-3p0@20c8120 { - reg = <0x20c8120>; + regulator-3p0 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd3p0"; regulator-min-microvolt = <2800000>; @@ -621,8 +618,7 @@ anatop-enable-bit = <0>; }; - regulator-2p5@20c8130 { - reg = <0x20c8130>; + regulator-2p5 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd2p5"; regulator-min-microvolt = <2100000>; @@ -637,8 +633,7 @@ anatop-enable-bit = <0>; }; - reg_arm: regulator-vddcore@20c8140 { - reg = <0x20c8140>; + reg_arm: regulator-vddcore { compatible = "fsl,anatop-regulator"; regulator-name = "vddarm"; regulator-min-microvolt = <725000>; @@ -655,8 +650,7 @@ anatop-max-voltage = <1450000>; }; - reg_pcie: regulator-vddpcie@20c8140 { - reg = <0x20c8140>; + reg_pcie: regulator-vddpcie { compatible = "fsl,anatop-regulator"; regulator-name = "vddpcie"; regulator-min-microvolt = <725000>; @@ -672,8 +666,7 @@ anatop-max-voltage = <1450000>; }; - reg_soc: regulator-vddsoc@20c8140 { - reg = <0x20c8140>; + reg_soc: regulator-vddsoc { compatible = "fsl,anatop-regulator"; regulator-name = "vddsoc"; regulator-min-microvolt = <725000>; diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dts b/arch/arm/boot/dts/imx6ul-14x14-evk.dts index 6d720b20e7ed..2438669f149a 100644 --- a/arch/arm/boot/dts/imx6ul-14x14-evk.dts +++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dts @@ -1,10 +1,6 @@ -/* - * Copyright (C) 2015 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright (C) 2015 Freescale Semiconductor, Inc. /dts-v1/; diff --git a/arch/arm/boot/dts/imx6ul-isiot.dtsi b/arch/arm/boot/dts/imx6ul-isiot.dtsi index 921e12c69a00..cd9928551154 100644 --- a/arch/arm/boot/dts/imx6ul-isiot.dtsi +++ b/arch/arm/boot/dts/imx6ul-isiot.dtsi @@ -153,8 +153,6 @@ stmpe811: gpio-expander@44 { compatible = "st,stmpe811"; reg = <0x44>; - #address-cells = <1>; - #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_stmpe>; interrupt-parent = <&gpio1>; diff --git a/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts b/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts index 2d80f7b50bc0..97686097a86e 100644 --- a/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts +++ b/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts @@ -48,7 +48,7 @@ compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul"; aliases { - lcdif_24bit_pins_a = &pinctrl_disp0_3; + lcdif-24bit-pins-a = &pinctrl_disp0_3; mmc0 = &usdhc1; /delete-property/ mmc1; serial2 = &uart3; diff --git a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi index f678d18ad44a..02b5ba42cd59 100644 --- a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi +++ b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi @@ -53,10 +53,10 @@ i2c2 = &i2c1; i2c3 = &i2c3; i2c4 = &i2c4; - lcdif_23bit_pins_a = &pinctrl_disp0_1; - lcdif_24bit_pins_a = &pinctrl_disp0_2; + lcdif-23bit-pins-a = &pinctrl_disp0_1; + lcdif-24bit-pins-a = &pinctrl_disp0_2; pwm0 = &pwm5; - reg_can_xcvr = ®_can_xcvr; + reg-can-xcvr = ®_can_xcvr; serial2 = &uart5; serial4 = &uart3; spi0 = &ecspi2; diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi index 1241972b16ba..47a3453a4211 100644 --- a/arch/arm/boot/dts/imx6ul.dtsi +++ b/arch/arm/boot/dts/imx6ul.dtsi @@ -1,10 +1,6 @@ -/* - * Copyright 2015 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright 2015 Freescale Semiconductor, Inc. #include <dt-bindings/clock/imx6ul-clock.h> #include <dt-bindings/gpio/gpio.h> @@ -551,11 +547,8 @@ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - reg_3p0: regulator-3p0@20c8110 { - reg = <0x20c8110>; + reg_3p0: regulator-3p0 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd3p0"; regulator-min-microvolt = <2625000>; @@ -569,8 +562,7 @@ anatop-enable-bit = <0>; }; - reg_arm: regulator-vddcore@20c8140 { - reg = <0x20c8140>; + reg_arm: regulator-vddcore { compatible = "fsl,anatop-regulator"; regulator-name = "cpu"; regulator-min-microvolt = <725000>; @@ -587,8 +579,7 @@ anatop-max-voltage = <1450000>; }; - reg_soc: regulator-vddsoc@20c8140 { - reg = <0x20c8140>; + reg_soc: regulator-vddsoc { compatible = "fsl,anatop-regulator"; regulator-name = "vddsoc"; regulator-min-microvolt = <725000>; @@ -769,6 +760,36 @@ reg = <0x02100000 0x100000>; ranges; + crypto: caam@2140000 { + compatible = "fsl,imx6ul-caam", "fsl,sec-v4.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x2140000 0x3c000>; + ranges = <0 0x2140000 0x3c000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6UL_CLK_CAAM_IPG>, <&clks IMX6UL_CLK_CAAM_ACLK>, + <&clks IMX6UL_CLK_CAAM_MEM>; + clock-names = "ipg", "aclk", "mem"; + + sec_jr0: jr0@1000 { + compatible = "fsl,sec-v4.0-job-ring"; + reg = <0x1000 0x1000>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + }; + + sec_jr1: jr1@2000 { + compatible = "fsl,sec-v4.0-job-ring"; + reg = <0x2000 0x1000>; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; + }; + + sec_jr2: jr2@3000 { + compatible = "fsl,sec-v4.0-job-ring"; + reg = <0x3000 0x1000>; + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + usbotg1: usb@2184000 { compatible = "fsl,imx6ul-usb", "fsl,imx27-usb"; reg = <0x02184000 0x200>; diff --git a/arch/arm/boot/dts/imx6ull-pinfunc.h b/arch/arm/boot/dts/imx6ull-pinfunc.h index 118202336691..fdc46bb09cc1 100644 --- a/arch/arm/boot/dts/imx6ull-pinfunc.h +++ b/arch/arm/boot/dts/imx6ull-pinfunc.h @@ -14,6 +14,14 @@ * The pin function ID is a tuple of * <mux_reg conf_reg input_reg mux_mode input_val> */ +#define MX6ULL_PAD_UART1_TX_DATA__UART5_DTE_RX 0x0084 0x0310 0x0644 0x9 0x4 +#define MX6ULL_PAD_UART1_RX_DATA__UART5_DCE_RX 0x0088 0x0314 0x0644 0x9 0x5 +#define MX6ULL_PAD_UART1_CTS_B__UART5_DCE_RTS 0x008C 0x0318 0x0640 0x9 0x3 +#define MX6ULL_PAD_UART1_RTS_B__UART5_DTE_RTS 0x0090 0x031C 0x0640 0x9 0x4 +#define MX6ULL_PAD_UART5_TX_DATA__UART5_DTE_RX 0x00BC 0x0348 0x0644 0x0 0x6 +#define MX6ULL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x00C0 0x034C 0x0644 0x0 0x7 +#define MX6ULL_PAD_ENET1_RX_EN__UART5_DCE_RTS 0x00CC 0x0358 0x0640 0x1 0x5 +#define MX6ULL_PAD_ENET1_TX_DATA0__UART5_DTE_RTS 0x00D0 0x035C 0x0640 0x1 0x6 #define MX6ULL_PAD_ENET2_RX_DATA0__EPDC_SDDO08 0x00E4 0x0370 0x0000 0x9 0x0 #define MX6ULL_PAD_ENET2_RX_DATA1__EPDC_SDDO09 0x00E8 0x0374 0x0000 0x9 0x0 #define MX6ULL_PAD_ENET2_RX_EN__EPDC_SDDO10 0x00EC 0x0378 0x0000 0x9 0x0 @@ -47,6 +55,7 @@ #define MX6ULL_PAD_CSI_DATA00__ESAI_TX_HF_CLK 0x01E4 0x0470 0x0000 0x9 0x0 #define MX6ULL_PAD_CSI_DATA01__ESAI_RX_HF_CLK 0x01E8 0x0474 0x0000 0x9 0x0 #define MX6ULL_PAD_CSI_DATA02__ESAI_RX_FS 0x01EC 0x0478 0x0000 0x9 0x0 +#define MX6ULL_PAD_CSI_DATA02__UART5_DCE_RTS 0x01EC 0x0478 0x0640 0x8 0x7 #define MX6ULL_PAD_CSI_DATA03__ESAI_RX_CLK 0x01F0 0x047C 0x0000 0x9 0x0 #define MX6ULL_PAD_CSI_DATA04__ESAI_TX_FS 0x01F4 0x0480 0x0000 0x9 0x0 #define MX6ULL_PAD_CSI_DATA05__ESAI_TX_CLK 0x01F8 0x0484 0x0000 0x9 0x0 diff --git a/arch/arm/boot/dts/imx6ull.dtsi b/arch/arm/boot/dts/imx6ull.dtsi index 571ddd71cdba..ebc25c98e5e1 100644 --- a/arch/arm/boot/dts/imx6ull.dtsi +++ b/arch/arm/boot/dts/imx6ull.dtsi @@ -45,6 +45,8 @@ /* Delete UART8 in AIPS-1 (i.MX6UL specific) */ /delete-node/ &uart8; +/* Delete CAAM node in AIPS-2 (i.MX6UL specific) */ +/delete-node/ &crypto; / { soc { diff --git a/arch/arm/boot/dts/imx7d-cl-som-imx7.dts b/arch/arm/boot/dts/imx7d-cl-som-imx7.dts index 7f645683f53b..8bf365d28cac 100644 --- a/arch/arm/boot/dts/imx7d-cl-som-imx7.dts +++ b/arch/arm/boot/dts/imx7d-cl-som-imx7.dts @@ -33,7 +33,7 @@ }; &cpu0 { - arm-supply = <&sw1a_reg>; + cpu-supply = <&sw1a_reg>; }; &fec1 { diff --git a/arch/arm/boot/dts/imx7d-nitrogen7.dts b/arch/arm/boot/dts/imx7d-nitrogen7.dts index 52167298984d..70c53e50b2fc 100644 --- a/arch/arm/boot/dts/imx7d-nitrogen7.dts +++ b/arch/arm/boot/dts/imx7d-nitrogen7.dts @@ -49,8 +49,8 @@ compatible = "boundary,imx7d-nitrogen7", "fsl,imx7d"; aliases { - fb_lcd = &lcdif; - t_lcd = &t_lcd; + fb-lcd = &lcdif; + t-lcd = &t_lcd; }; memory@80000000 { @@ -144,7 +144,7 @@ }; &cpu0 { - arm-supply = <&sw1a_reg>; + cpu-supply = <&sw1a_reg>; }; &fec1 { diff --git a/arch/arm/boot/dts/imx7d-pinfunc.h b/arch/arm/boot/dts/imx7d-pinfunc.h index f2493bc63da4..aa9dbead4b8b 100644 --- a/arch/arm/boot/dts/imx7d-pinfunc.h +++ b/arch/arm/boot/dts/imx7d-pinfunc.h @@ -592,7 +592,7 @@ #define MX7D_PAD_UART2_RX_DATA__UART2_DCE_RX 0x0130 0x03A0 0x06FC 0x0 0x2 #define MX7D_PAD_UART2_RX_DATA__UART2_DTE_TX 0x0130 0x03A0 0x0000 0x0 0x0 #define MX7D_PAD_UART2_RX_DATA__I2C2_SCL 0x0130 0x03A0 0x05DC 0x1 0x0 -#define MX7D_PAD_UART2_RX_DATA__SAI3_RX_BCLK 0x0130 0x03A0 0x0000 0x2 0x0 +#define MX7D_PAD_UART2_RX_DATA__SAI3_RX_BCLK 0x0130 0x03A0 0x06C4 0x2 0x0 #define MX7D_PAD_UART2_RX_DATA__ECSPI1_SS3 0x0130 0x03A0 0x0000 0x3 0x0 #define MX7D_PAD_UART2_RX_DATA__ENET2_1588_EVENT1_IN 0x0130 0x03A0 0x0000 0x4 0x0 #define MX7D_PAD_UART2_RX_DATA__GPIO4_IO2 0x0130 0x03A0 0x0000 0x5 0x0 @@ -1112,13 +1112,13 @@ #define MX7D_PAD_ENET1_RGMII_TD3__GPIO7_IO9 0x0250 0x04C0 0x0000 0x5 0x0 #define MX7D_PAD_ENET1_RGMII_TD3__CAAM_RNG_OSC_OBS 0x0250 0x04C0 0x0000 0x7 0x0 #define MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x0254 0x04C4 0x0000 0x0 0x0 -#define MX7D_PAD_ENET1_RGMII_TX_CTL__SAI1_RX_SYNC 0x0254 0x04C4 0x0000 0x2 0x0 +#define MX7D_PAD_ENET1_RGMII_TX_CTL__SAI1_RX_SYNC 0x0254 0x04C4 0x06A4 0x2 0x1 #define MX7D_PAD_ENET1_RGMII_TX_CTL__GPT2_COMPARE1 0x0254 0x04C4 0x0000 0x3 0x0 #define MX7D_PAD_ENET1_RGMII_TX_CTL__EPDC_PWR_CTRL2 0x0254 0x04C4 0x0000 0x4 0x0 #define MX7D_PAD_ENET1_RGMII_TX_CTL__GPIO7_IO10 0x0254 0x04C4 0x0000 0x5 0x0 #define MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC 0x0258 0x04C8 0x0000 0x0 0x0 #define MX7D_PAD_ENET1_RGMII_TXC__ENET1_TX_ER 0x0258 0x04C8 0x0000 0x1 0x0 -#define MX7D_PAD_ENET1_RGMII_TXC__SAI1_RX_BCLK 0x0258 0x04C8 0x0000 0x2 0x0 +#define MX7D_PAD_ENET1_RGMII_TXC__SAI1_RX_BCLK 0x0258 0x04C8 0x069C 0x2 0x1 #define MX7D_PAD_ENET1_RGMII_TXC__GPT2_COMPARE2 0x0258 0x04C8 0x0000 0x3 0x0 #define MX7D_PAD_ENET1_RGMII_TXC__EPDC_PWR_CTRL3 0x0258 0x04C8 0x0000 0x4 0x0 #define MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11 0x0258 0x04C8 0x0000 0x5 0x0 diff --git a/arch/arm/boot/dts/imx7d-sdb-sht11.dts b/arch/arm/boot/dts/imx7d-sdb-sht11.dts index 64a20ed1713a..996555596d40 100644 --- a/arch/arm/boot/dts/imx7d-sdb-sht11.dts +++ b/arch/arm/boot/dts/imx7d-sdb-sht11.dts @@ -1,44 +1,6 @@ -/* - * Copyright (C) 2015 Freescale Semiconductor, Inc. - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +// +// Copyright (C) 2015 Freescale Semiconductor, Inc. #include "imx7d-sdb.dts" diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts index 5d6a08be397f..940849163104 100644 --- a/arch/arm/boot/dts/imx7d-sdb.dts +++ b/arch/arm/boot/dts/imx7d-sdb.dts @@ -1,44 +1,6 @@ -/* - * Copyright (C) 2015 Freescale Semiconductor, Inc. - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +// +// Copyright (C) 2015 Freescale Semiconductor, Inc. /dts-v1/; @@ -52,6 +14,24 @@ reg = <0x80000000 0x80000000>; }; + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; + + volume-up { + label = "Volume Up"; + gpios = <&gpio5 11 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + + volume-down { + label = "Volume Down"; + gpios = <&gpio5 10 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + }; + }; + spi4 { compatible = "spi-gpio"; pinctrl-names = "default"; @@ -161,7 +141,7 @@ }; &cpu0 { - arm-supply = <&sw1a_reg>; + cpu-supply = <&sw1a_reg>; }; &ecspi3 { @@ -519,6 +499,12 @@ >; }; + pinctrl_gpio_keys: gpio_keysgrp { + fsl,pins = < + MX7D_PAD_SD2_RESET_B__GPIO5_IO11 0x59 + MX7D_PAD_SD2_WP__GPIO5_IO10 0x59 + >; + }; pinctrl_hog: hoggrp { fsl,pins = < diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi index 200714e3feea..8d3d123d0a5c 100644 --- a/arch/arm/boot/dts/imx7d.dtsi +++ b/arch/arm/boot/dts/imx7d.dtsi @@ -1,45 +1,7 @@ -/* - * Copyright 2015 Freescale Semiconductor, Inc. - * Copyright 2016 Toradex AG - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +// +// Copyright 2015 Freescale Semiconductor, Inc. +// Copyright 2016 Toradex AG #include "imx7s.dtsi" #include <dt-bindings/reset/imx7-reset.h> @@ -47,12 +9,8 @@ / { cpus { cpu0: cpu@0 { - operating-points = < - /* KHz uV */ - 996000 1075000 - 792000 975000 - >; clock-frequency = <996000000>; + operating-points-v2 = <&cpu0_opp_table>; }; cpu1: cpu@1 { @@ -60,6 +18,25 @@ device_type = "cpu"; reg = <1>; clock-frequency = <996000000>; + operating-points-v2 = <&cpu0_opp_table>; + }; + }; + + cpu0_opp_table: opp-table { + compatible = "operating-points-v2"; + opp-shared; + + opp-792000000 { + opp-hz = /bits/ 64 <792000000>; + opp-microvolt = <975000>; + clock-latency-ns = <150000>; + }; + + opp-996000000 { + opp-hz = /bits/ 64 <996000000>; + opp-microvolt = <1075000>; + clock-latency-ns = <150000>; + opp-suspend; }; }; @@ -120,7 +97,7 @@ <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>, + clocks = <&clks IMX7D_ENET2_IPG_ROOT_CLK>, <&clks IMX7D_ENET_AXI_ROOT_CLK>, <&clks IMX7D_ENET2_TIME_ROOT_CLK>, <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>, diff --git a/arch/arm/boot/dts/imx7s-warp.dts b/arch/arm/boot/dts/imx7s-warp.dts index 8a30b148534d..fa390da636de 100644 --- a/arch/arm/boot/dts/imx7s-warp.dts +++ b/arch/arm/boot/dts/imx7s-warp.dts @@ -113,10 +113,6 @@ assigned-clock-rates = <884736000>; }; -&cpu0 { - arm-supply = <&sw1a_reg>; -}; - &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c1>; diff --git a/arch/arm/boot/dts/imx7s.dtsi b/arch/arm/boot/dts/imx7s.dtsi index 4d42335c0dee..9ced589bfa96 100644 --- a/arch/arm/boot/dts/imx7s.dtsi +++ b/arch/arm/boot/dts/imx7s.dtsi @@ -1,45 +1,7 @@ -/* - * Copyright 2015 Freescale Semiconductor, Inc. - * Copyright 2016 Toradex AG - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +// +// Copyright 2015 Freescale Semiconductor, Inc. +// Copyright 2016 Toradex AG #include <dt-bindings/clock/imx7d-clock.h> #include <dt-bindings/power/imx7-power.h> @@ -173,6 +135,17 @@ }; }; + tempmon: tempmon { + compatible = "fsl,imx7d-tempmon"; + interrupt-parent = <&gpc>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; + fsl,tempmon =<&anatop>; + nvmem-cells = <&tempmon_calib>, + <&tempmon_temp_grade>; + nvmem-cell-names = "calib", "temp_grade"; + clocks = <&clks IMX7D_PLL_SYS_MAIN_CLK>; + }; + timer { compatible = "arm,armv7-timer"; interrupt-parent = <&intc>; @@ -321,7 +294,7 @@ port { tpiu_in_port: endpoint { slave-mode; - remote-endpoint = <&replicator_out_port1>; + remote-endpoint = <&replicator_out_port0>; }; }; }; @@ -540,27 +513,14 @@ }; }; - tempmon: tempmon { - compatible = "fsl,imx7d-tempmon"; - interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; - fsl,tempmon =<&anatop>; - nvmem-cells = <&tempmon_calib>, - <&tempmon_temp_grade>; - nvmem-cell-names = "calib", "temp_grade"; - clocks = <&clks IMX7D_PLL_SYS_MAIN_CLK>; - }; - anatop: anatop@30360000 { compatible = "fsl,imx7d-anatop", "fsl,imx6q-anatop", "syscon", "simple-bus"; reg = <0x30360000 0x10000>; interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - reg_1p0d: regulator-vdd1p0d@30360210 { - reg = <0x30360210>; + reg_1p0d: regulator-vdd1p0d { compatible = "fsl,anatop-regulator"; regulator-name = "vdd1p0d"; regulator-min-microvolt = <800000>; @@ -573,6 +533,20 @@ anatop-max-voltage = <1200000>; anatop-enable-bit = <0>; }; + + reg_1p2: regulator-vdd1p2 { + compatible = "fsl,anatop-regulator"; + regulator-name = "vdd1p2"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + anatop-reg-offset = <0x220>; + anatop-vol-bit-shift = <8>; + anatop-vol-bit-width = <5>; + anatop-min-bit-val = <0x14>; + anatop-min-voltage = <1100000>; + anatop-max-voltage = <1300000>; + anatop-enable-bit = <0>; + }; }; snvs: snvs@30370000 { @@ -868,6 +842,7 @@ crypto: caam@30900000 { compatible = "fsl,sec-v4.0"; + fsl,sec-era = <8>; #address-cells = <1>; #size-cells = <1>; reg = <0x30900000 0x40000>; @@ -1091,7 +1066,7 @@ <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>, + clocks = <&clks IMX7D_ENET1_IPG_ROOT_CLK>, <&clks IMX7D_ENET_AXI_ROOT_CLK>, <&clks IMX7D_ENET1_TIME_ROOT_CLK>, <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>, diff --git a/arch/arm/boot/dts/keystone-k2g-evm.dts b/arch/arm/boot/dts/keystone-k2g-evm.dts index 6a4657799b99..154fdd7a7022 100644 --- a/arch/arm/boot/dts/keystone-k2g-evm.dts +++ b/arch/arm/boot/dts/keystone-k2g-evm.dts @@ -114,6 +114,20 @@ K2G_CORE_IOPAD(0x11f0) (BUFFER_CLASS_B | PIN_PULLDOWN | MUX_MODE0) /* uart2_txd.uart2_txd */ >; }; + + dcan0_pins: pinmux_dcan0_pins { + pinctrl-single,pins = < + K2G_CORE_IOPAD(0x11fc) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dcan0tx.dcan0tx */ + K2G_CORE_IOPAD(0x1200) (BUFFER_CLASS_B | PIN_PULLDOWN | MUX_MODE0) /* dcan0rx.dcan0rx */ + >; + }; + + dcan1_pins: pinmux_dcan1_pins { + pinctrl-single,pins = < + K2G_CORE_IOPAD(0x1224) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE1) /* qspicsn2.dcan1tx */ + K2G_CORE_IOPAD(0x1228) (BUFFER_CLASS_B | PIN_PULLDOWN | MUX_MODE1) /* qspicsn3.dcan1rx */ + >; + }; }; &uart0 { @@ -268,3 +282,15 @@ pinctrl-0 = <&uart2_pins>; status = "okay"; }; + +&dcan0 { + pinctrl-names = "default"; + pinctrl-0 = <&dcan0_pins>; + status = "okay"; +}; + +&dcan1 { + pinctrl-names = "default"; + pinctrl-0 = <&dcan1_pins>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/logicpd-som-lv.dtsi b/arch/arm/boot/dts/logicpd-som-lv.dtsi index b47cac23a04b..3bb28c03ca74 100644 --- a/arch/arm/boot/dts/logicpd-som-lv.dtsi +++ b/arch/arm/boot/dts/logicpd-som-lv.dtsi @@ -26,7 +26,7 @@ gpio = <&gpio1 3 0>; /* gpio_3 */ startup-delay-us = <70000>; enable-active-high; - vin-supply = <&vmmc2>; + vin-supply = <&vaux3>; }; /* HS USB Host PHY on PORT 1 */ @@ -35,6 +35,13 @@ reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */ #phy-cells = <0>; }; + + /* fixed 26MHz oscillator */ + hfclk_26m: oscillator { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <26000000>; + }; }; &gpmc { @@ -79,9 +86,12 @@ reg = <0x48>; interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; + clocks = <&hfclk_26m>; + clock-names = "fck"; twl_audio: audio { compatible = "ti,twl4030-audio"; codec { + ti,hs_extmute_gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>; }; }; }; @@ -97,6 +107,25 @@ pinctrl-names = "default"; pinctrl-0 = <&i2c3_pins>; clock-frequency = <400000>; + + touchscreen: tsc2004@48 { + compatible = "ti,tsc2004"; + reg = <0x48>; + vio-supply = <&vaux1>; + pinctrl-names = "default"; + pinctrl-0 = <&tsc2004_pins>; + interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; }; &mmc3 { @@ -199,6 +228,13 @@ pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ + OMAP3_CORE1_IOPAD(0x20ba, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs6.gpio_57 */ + >; + }; + + tsc2004_pins: pinmux_tsc2004_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */ >; }; }; @@ -213,7 +249,7 @@ }; wl127x_gpio: pinmux_wl127x_gpio_pin { pinctrl-single,pins = < - OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */ + OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */ OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */ >; }; @@ -260,6 +296,11 @@ #include "twl4030.dtsi" #include "twl4030_omap3.dtsi" +&vaux3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + &twl { twl_power: power { compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle"; diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi index 3e174e474d3d..7d2302e8706c 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi +++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi @@ -30,6 +30,13 @@ linux,default-trigger = "none"; }; }; + + /* fixed 26MHz oscillator */ + hfclk_26m: oscillator { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <26000000>; + }; }; &gpmc { @@ -74,6 +81,9 @@ reg = <0x48>; interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; + clocks = <&hfclk_26m>; + clock-names = "fck"; + twl_audio: audio { compatible = "ti,twl4030-audio"; codec { diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi index dcc9292d2ffa..d77dcf890cfc 100644 --- a/arch/arm/boot/dts/meson8.dtsi +++ b/arch/arm/boot/dts/meson8.dtsi @@ -57,7 +57,7 @@ #address-cells = <1>; #size-cells = <0>; - cpu@200 { + cpu0: cpu@200 { device_type = "cpu"; compatible = "arm,cortex-a9"; next-level-cache = <&L2>; @@ -66,7 +66,7 @@ resets = <&clkc CLKC_RESET_CPU0_SOFT_RESET>; }; - cpu@201 { + cpu1: cpu@201 { device_type = "cpu"; compatible = "arm,cortex-a9"; next-level-cache = <&L2>; @@ -75,7 +75,7 @@ resets = <&clkc CLKC_RESET_CPU1_SOFT_RESET>; }; - cpu@202 { + cpu2: cpu@202 { device_type = "cpu"; compatible = "arm,cortex-a9"; next-level-cache = <&L2>; @@ -84,7 +84,7 @@ resets = <&clkc CLKC_RESET_CPU2_SOFT_RESET>; }; - cpu@203 { + cpu3: cpu@203 { device_type = "cpu"; compatible = "arm,cortex-a9"; next-level-cache = <&L2>; @@ -94,6 +94,15 @@ }; }; + pmu { + compatible = "arm,cortex-a9-pmu"; + interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; + }; + reserved-memory { #address-cells = <1>; #size-cells = <1>; @@ -272,6 +281,22 @@ function = "pwm_e"; }; }; + + uart_a1_pins: uart-a1 { + mux { + groups = "uart_tx_a1", + "uart_rx_a1"; + function = "uart_a"; + }; + }; + + uart_a1_cts_rts_pins: uart-a1-cts-rts { + mux { + groups = "uart_cts_a1", + "uart_rts_a1"; + function = "uart_a"; + }; + }; }; }; diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts index 3a5603d95b70..ef3177d3da3d 100644 --- a/arch/arm/boot/dts/meson8b-odroidc1.dts +++ b/arch/arm/boot/dts/meson8b-odroidc1.dts @@ -103,10 +103,34 @@ }; }; -&uart_AO { +ðmac { status = "okay"; - pinctrl-0 = <&uart_ao_a_pins>; + + snps,reset-gpio = <&gpio GPIOH_4 GPIO_ACTIVE_HIGH>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 30000>; + + pinctrl-0 = <ð_rgmii_pins>; pinctrl-names = "default"; + + phy-mode = "rgmii"; + phy-handle = <ð_phy>; + amlogic,tx-delay-ns = <4>; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + /* Realtek RTL8211F (0x001cc916) */ + eth_phy: ethernet-phy@0 { + reg = <0>; + eee-broken-1000t; + interrupt-parent = <&gpio_intc>; + /* GPIOH_3 */ + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + }; + }; }; &gpio_ao { @@ -124,12 +148,10 @@ }; }; -&usb1_phy { - status = "okay"; -}; - -&usb1 { +&ir_receiver { status = "okay"; + pinctrl-0 = <&ir_recv_pins>; + pinctrl-names = "default"; }; &sdio { @@ -158,32 +180,16 @@ }; }; -ðmac { +&uart_AO { status = "okay"; - - snps,reset-gpio = <&gpio GPIOH_4 GPIO_ACTIVE_HIGH>; - snps,reset-active-low; - snps,reset-delays-us = <0 10000 30000>; - - pinctrl-0 = <ð_rgmii_pins>; + pinctrl-0 = <&uart_ao_a_pins>; pinctrl-names = "default"; +}; - phy-mode = "rgmii"; - phy-handle = <ð_phy>; - amlogic,tx-delay-ns = <4>; - - mdio { - compatible = "snps,dwmac-mdio"; - #address-cells = <1>; - #size-cells = <0>; +&usb1_phy { + status = "okay"; +}; - /* Realtek RTL8211F (0x001cc916) */ - eth_phy: ethernet-phy@0 { - reg = <0>; - eee-broken-1000t; - interrupt-parent = <&gpio_intc>; - /* GPIOH_3 */ - interrupts = <17 IRQ_TYPE_LEVEL_LOW>; - }; - }; +&usb1 { + status = "okay"; }; diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi index 553b82174604..08f7f6be7254 100644 --- a/arch/arm/boot/dts/meson8b.dtsi +++ b/arch/arm/boot/dts/meson8b.dtsi @@ -55,7 +55,7 @@ #address-cells = <1>; #size-cells = <0>; - cpu@200 { + cpu0: cpu@200 { device_type = "cpu"; compatible = "arm,cortex-a5"; next-level-cache = <&L2>; @@ -64,7 +64,7 @@ resets = <&clkc CLKC_RESET_CPU0_SOFT_RESET>; }; - cpu@201 { + cpu1: cpu@201 { device_type = "cpu"; compatible = "arm,cortex-a5"; next-level-cache = <&L2>; @@ -73,7 +73,7 @@ resets = <&clkc CLKC_RESET_CPU1_SOFT_RESET>; }; - cpu@202 { + cpu2: cpu@202 { device_type = "cpu"; compatible = "arm,cortex-a5"; next-level-cache = <&L2>; @@ -82,7 +82,7 @@ resets = <&clkc CLKC_RESET_CPU2_SOFT_RESET>; }; - cpu@203 { + cpu3: cpu@203 { device_type = "cpu"; compatible = "arm,cortex-a5"; next-level-cache = <&L2>; @@ -92,6 +92,15 @@ }; }; + pmu { + compatible = "arm,cortex-a5-pmu"; + interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; + }; + reserved-memory { #address-cells = <1>; #size-cells = <1>; @@ -139,6 +148,13 @@ function = "uart_ao"; }; }; + + ir_recv_pins: remote { + mux { + groups = "remote_input"; + function = "remote"; + }; + }; }; }; diff --git a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts new file mode 100644 index 000000000000..f5853610b20b --- /dev/null +++ b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts @@ -0,0 +1,244 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Oleg Ivanov <balbes-150@yandex.ru> + * Copyright (c) 2018 Martin Blumenstingl <martin.blumenstingl@googlemail.com> + */ + +/dts-v1/; + +#include "meson8m2.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "Tronsmart MXIII Plus"; + compatible = "tronsmart,mxiii-plus", "amlogic,meson8m2"; + + aliases { + ethernet0 = ðmac; + i2c0 = &i2c_AO; + serial0 = &uart_AO; + serial1 = &uart_A; + mmc0 = &sd_card_slot; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0x40000000 0x80000000>; + }; + + adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 0>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1710000>; + + button-function { + label = "Function"; + linux,code = <KEY_FN>; + press-threshold-microvolt = <10000>; + }; + }; + + vcc_3v3: regulator-vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&cpu0 { + cpu-supply = <&vcck>; +}; + +ðmac { + status = "okay"; + + pinctrl-0 = <ð_rgmii_pins>; + pinctrl-names = "default"; + + phy-handle = <ð_phy0>; + phy-mode = "rgmii"; + + amlogic,tx-delay-ns = <4>; + + snps,reset-gpio = <&gpio GPIOH_4 0>; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-active-low; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + eth_phy0: ethernet-phy@0 { + /* Realtek RTL8211F (0x001cc916) */ + reg = <0>; + }; + }; +}; + +&ir_receiver { + status = "okay"; + pinctrl-0 = <&ir_recv_pins>; + pinctrl-names = "default"; +}; + +&i2c_AO { + status = "okay"; + pinctrl-0 = <&i2c_ao_pins>; + pinctrl-names = "default"; + + pmic@32 { + compatible = "ricoh,rn5t618"; + reg = <0x32>; + system-power-controller; + + regulators { + vcck: DCDC1 { + regulator-name = "VCCK"; + regulator-min-microvolt = <825000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + DCDC2 { + regulator-name = "VDDAO"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + DCDC3 { + regulator-name = "VDD_DDR"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + LDO1 { + regulator-name = "VDDIO_AO28"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + regulator-boot-on; + regulator-always-on; + }; + + vddio_ao1v8: LDO2 { + regulator-name = "VDDIO_AO18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + LDO3 { + regulator-name = "VCC1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + LDO4 { + regulator-name = "VCC2V8"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-boot-on; + regulator-always-on; + }; + + LDO5 { + regulator-name = "AVDD1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + LDORTC1 { + regulator-name = "VDD_LDO"; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + regulator-boot-on; + regulator-always-on; + }; + + LDORTC2 { + regulator-name = "RTC_0V9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&saradc { + status = "okay"; + vref-supply = <&vddio_ao1v8>; +}; + +&sdio { + status = "okay"; + + pinctrl-0 = <&sd_b_pins>; + pinctrl-names = "default"; + + /* SD card */ + sd_card_slot: slot@1 { + compatible = "mmc-slot"; + reg = <1>; + status = "okay"; + + bus-width = <4>; + no-sdio; + cap-mmc-highspeed; + cap-sd-highspeed; + disable-wp; + + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>; + cd-inverted; + + vmmc-supply = <&vcc_3v3>; + }; +}; + +/* connected to the Bluetooth module */ +&uart_A { + status = "okay"; + pinctrl-0 = <&uart_a1_pins>, <&uart_a1_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/meson8m2.dtsi b/arch/arm/boot/dts/meson8m2.dtsi new file mode 100644 index 000000000000..3e1f92273d7b --- /dev/null +++ b/arch/arm/boot/dts/meson8m2.dtsi @@ -0,0 +1,54 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2017 Martin Blumenstingl <martin.blumenstingl@googlemail.com>. + */ + +#include "meson8.dtsi" + +/ { + model = "Amlogic Meson8m2 SoC"; + compatible = "amlogic,meson8m2"; +}; /* end of / */ + +&clkc { + compatible = "amlogic,meson8m2-clkc", "amlogic,meson8-clkc"; +}; + +ðmac { + compatible = "amlogic,meson8m2-dwmac", "snps,dwmac"; + reg = <0xc9410000 0x10000 + 0xc1108140 0x8>; + clocks = <&clkc CLKID_ETH>, + <&clkc CLKID_MPLL2>, + <&clkc CLKID_MPLL2>; + clock-names = "stmmaceth", "clkin0", "clkin1"; + resets = <&reset RESET_ETHERNET>; + reset-names = "stmmaceth"; +}; + +&pinctrl_aobus { + compatible = "amlogic,meson8m2-aobus-pinctrl", + "amlogic,meson8-aobus-pinctrl"; +}; + +&pinctrl_cbus { + compatible = "amlogic,meson8m2-cbus-pinctrl", + "amlogic,meson8-cbus-pinctrl"; + + eth_rgmii_pins: ethernet { + mux { + groups = "eth_tx_clk_50m", "eth_tx_en", + "eth_txd3", "eth_txd2", + "eth_txd1", "eth_txd0", + "eth_rx_clk_in", "eth_rx_dv", + "eth_rxd3", "eth_rxd2", + "eth_rxd1", "eth_rxd0", + "eth_mdio", "eth_mdc"; + function = "ethernet"; + }; + }; +}; + +&wdt { + compatible = "amlogic,meson8m2-wdt", "amlogic,meson8b-wdt"; +}; diff --git a/arch/arm/boot/dts/mt2701-evb.dts b/arch/arm/boot/dts/mt2701-evb.dts index 63af4b13a36f..be0edb3dae6c 100644 --- a/arch/arm/boot/dts/mt2701-evb.dts +++ b/arch/arm/boot/dts/mt2701-evb.dts @@ -1,15 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2015 MediaTek Inc. * Author: Erin Lo <erin.lo@mediatek.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ /dts-v1/; diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi index 05557fce0f1d..180377e56ef4 100644 --- a/arch/arm/boot/dts/mt2701.dtsi +++ b/arch/arm/boot/dts/mt2701.dtsi @@ -1,15 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2015 MediaTek Inc. * Author: Erin.Lo <erin.lo@mediatek.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ #include <dt-bindings/clock/mt2701-clk.h> @@ -426,104 +419,96 @@ status = "disabled"; }; - afe: audio-controller@11220000 { - compatible = "mediatek,mt2701-audio"; - reg = <0 0x11220000 0 0x2000>, - <0 0x112a0000 0 0x20000>; - interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>; - interrupt-names = "afe", "asys"; - power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>; - - clocks = <&infracfg CLK_INFRA_AUDIO>, - <&topckgen CLK_TOP_AUD_MUX1_SEL>, - <&topckgen CLK_TOP_AUD_MUX2_SEL>, - <&topckgen CLK_TOP_AUD_MUX1_DIV>, - <&topckgen CLK_TOP_AUD_MUX2_DIV>, - <&topckgen CLK_TOP_AUD_48K_TIMING>, - <&topckgen CLK_TOP_AUD_44K_TIMING>, - <&topckgen CLK_TOP_AUDPLL_MUX_SEL>, - <&topckgen CLK_TOP_APLL_SEL>, - <&topckgen CLK_TOP_AUD1PLL_98M>, - <&topckgen CLK_TOP_AUD2PLL_90M>, - <&topckgen CLK_TOP_HADDS2PLL_98M>, - <&topckgen CLK_TOP_HADDS2PLL_294M>, - <&topckgen CLK_TOP_AUDPLL>, - <&topckgen CLK_TOP_AUDPLL_D4>, - <&topckgen CLK_TOP_AUDPLL_D8>, - <&topckgen CLK_TOP_AUDPLL_D16>, - <&topckgen CLK_TOP_AUDPLL_D24>, - <&topckgen CLK_TOP_AUDINTBUS_SEL>, - <&clk26m>, - <&topckgen CLK_TOP_SYSPLL1_D4>, - <&topckgen CLK_TOP_AUD_K1_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K2_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K3_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K4_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K5_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K6_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K1_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K2_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K3_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K4_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K5_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K6_SRC_DIV>, - <&topckgen CLK_TOP_AUD_I2S1_MCLK>, - <&topckgen CLK_TOP_AUD_I2S2_MCLK>, - <&topckgen CLK_TOP_AUD_I2S3_MCLK>, - <&topckgen CLK_TOP_AUD_I2S4_MCLK>, - <&topckgen CLK_TOP_AUD_I2S5_MCLK>, - <&topckgen CLK_TOP_AUD_I2S6_MCLK>, - <&topckgen CLK_TOP_ASM_M_SEL>, - <&topckgen CLK_TOP_ASM_H_SEL>, - <&topckgen CLK_TOP_UNIVPLL2_D4>, - <&topckgen CLK_TOP_UNIVPLL2_D2>, - <&topckgen CLK_TOP_SYSPLL_D5>; - - clock-names = "infra_sys_audio_clk", - "top_audio_mux1_sel", - "top_audio_mux2_sel", - "top_audio_mux1_div", - "top_audio_mux2_div", - "top_audio_48k_timing", - "top_audio_44k_timing", - "top_audpll_mux_sel", - "top_apll_sel", - "top_aud1_pll_98M", - "top_aud2_pll_90M", - "top_hadds2_pll_98M", - "top_hadds2_pll_294M", - "top_audpll", - "top_audpll_d4", - "top_audpll_d8", - "top_audpll_d16", - "top_audpll_d24", - "top_audintbus_sel", - "clk_26m", - "top_syspll1_d4", - "top_aud_k1_src_sel", - "top_aud_k2_src_sel", - "top_aud_k3_src_sel", - "top_aud_k4_src_sel", - "top_aud_k5_src_sel", - "top_aud_k6_src_sel", - "top_aud_k1_src_div", - "top_aud_k2_src_div", - "top_aud_k3_src_div", - "top_aud_k4_src_div", - "top_aud_k5_src_div", - "top_aud_k6_src_div", - "top_aud_i2s1_mclk", - "top_aud_i2s2_mclk", - "top_aud_i2s3_mclk", - "top_aud_i2s4_mclk", - "top_aud_i2s5_mclk", - "top_aud_i2s6_mclk", - "top_asm_m_sel", - "top_asm_h_sel", - "top_univpll2_d4", - "top_univpll2_d2", - "top_syspll_d5"; + audsys: clock-controller@11220000 { + compatible = "mediatek,mt2701-audsys", "syscon"; + reg = <0 0x11220000 0 0x2000>; + #clock-cells = <1>; + + afe: audio-controller { + compatible = "mediatek,mt2701-audio"; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "afe", "asys"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>; + + clocks = <&infracfg CLK_INFRA_AUDIO>, + <&topckgen CLK_TOP_AUD_MUX1_SEL>, + <&topckgen CLK_TOP_AUD_MUX2_SEL>, + <&topckgen CLK_TOP_AUD_48K_TIMING>, + <&topckgen CLK_TOP_AUD_44K_TIMING>, + <&topckgen CLK_TOP_AUD_K1_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K2_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K3_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K4_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K1_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K2_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K3_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K4_SRC_DIV>, + <&topckgen CLK_TOP_AUD_I2S1_MCLK>, + <&topckgen CLK_TOP_AUD_I2S2_MCLK>, + <&topckgen CLK_TOP_AUD_I2S3_MCLK>, + <&topckgen CLK_TOP_AUD_I2S4_MCLK>, + <&audsys CLK_AUD_I2SO1>, + <&audsys CLK_AUD_I2SO2>, + <&audsys CLK_AUD_I2SO3>, + <&audsys CLK_AUD_I2SO4>, + <&audsys CLK_AUD_I2SIN1>, + <&audsys CLK_AUD_I2SIN2>, + <&audsys CLK_AUD_I2SIN3>, + <&audsys CLK_AUD_I2SIN4>, + <&audsys CLK_AUD_ASRCO1>, + <&audsys CLK_AUD_ASRCO2>, + <&audsys CLK_AUD_ASRCO3>, + <&audsys CLK_AUD_ASRCO4>, + <&audsys CLK_AUD_AFE>, + <&audsys CLK_AUD_AFE_CONN>, + <&audsys CLK_AUD_A1SYS>, + <&audsys CLK_AUD_A2SYS>, + <&audsys CLK_AUD_AFE_MRGIF>; + + clock-names = "infra_sys_audio_clk", + "top_audio_mux1_sel", + "top_audio_mux2_sel", + "top_audio_a1sys_hp", + "top_audio_a2sys_hp", + "i2s0_src_sel", + "i2s1_src_sel", + "i2s2_src_sel", + "i2s3_src_sel", + "i2s0_src_div", + "i2s1_src_div", + "i2s2_src_div", + "i2s3_src_div", + "i2s0_mclk_en", + "i2s1_mclk_en", + "i2s2_mclk_en", + "i2s3_mclk_en", + "i2so0_hop_ck", + "i2so1_hop_ck", + "i2so2_hop_ck", + "i2so3_hop_ck", + "i2si0_hop_ck", + "i2si1_hop_ck", + "i2si2_hop_ck", + "i2si3_hop_ck", + "asrc0_out_ck", + "asrc1_out_ck", + "asrc2_out_ck", + "asrc3_out_ck", + "audio_afe_pd", + "audio_afe_conn_pd", + "audio_a1sys_pd", + "audio_a2sys_pd", + "audio_mrgif_pd"; + + assigned-clocks = <&topckgen CLK_TOP_AUD_MUX1_SEL>, + <&topckgen CLK_TOP_AUD_MUX2_SEL>, + <&topckgen CLK_TOP_AUD_MUX1_DIV>, + <&topckgen CLK_TOP_AUD_MUX2_DIV>; + assigned-clock-parents = <&topckgen CLK_TOP_AUD1PLL_98M>, + <&topckgen CLK_TOP_AUD2PLL_90M>; + assigned-clock-rates = <0>, <0>, <49152000>, <45158400>; + }; }; mmsys: syscon@14000000 { diff --git a/arch/arm/boot/dts/mt6323.dtsi b/arch/arm/boot/dts/mt6323.dtsi index 7c783d6c750e..ba397407c1dd 100644 --- a/arch/arm/boot/dts/mt6323.dtsi +++ b/arch/arm/boot/dts/mt6323.dtsi @@ -1,15 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0 /* - * Copyright (c) 2017 MediaTek Inc. + * Copyright (c) 2017-2018 MediaTek Inc. * Author: John Crispin <john@phrozen.org> * Sean Wang <sean.wang@mediatek.com> - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ &pwrap { @@ -20,6 +14,13 @@ interrupt-controller; #interrupt-cells = <2>; + mt6323_leds: leds { + compatible = "mediatek,mt6323-led"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + mt6323regulator: mt6323regulator{ compatible = "mediatek,mt6323-regulator"; diff --git a/arch/arm/boot/dts/mt6580-evbp1.dts b/arch/arm/boot/dts/mt6580-evbp1.dts index 17daeae6bbe8..ca137897ed60 100644 --- a/arch/arm/boot/dts/mt6580-evbp1.dts +++ b/arch/arm/boot/dts/mt6580-evbp1.dts @@ -1,15 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2015 MediaTek Inc. * Author: Mars.C <mars.cheng@mediatek.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ /dts-v1/; diff --git a/arch/arm/boot/dts/mt6580.dtsi b/arch/arm/boot/dts/mt6580.dtsi index a349dba5ff79..2bdc5ed12fca 100644 --- a/arch/arm/boot/dts/mt6580.dtsi +++ b/arch/arm/boot/dts/mt6580.dtsi @@ -1,15 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2015 MediaTek Inc. * Author: Mars.C <mars.cheng@mediatek.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ #include <dt-bindings/interrupt-controller/irq.h> diff --git a/arch/arm/boot/dts/mt6589-aquaris5.dts b/arch/arm/boot/dts/mt6589-aquaris5.dts index 594a6f3bebda..7bbaa1279a26 100644 --- a/arch/arm/boot/dts/mt6589-aquaris5.dts +++ b/arch/arm/boot/dts/mt6589-aquaris5.dts @@ -1,16 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0+ /* * Copyright (c) 2014 MundoReader S.L. * Author: Matthias Brugger <matthias.bgg@gmail.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ /dts-v1/; diff --git a/arch/arm/boot/dts/mt6589.dtsi b/arch/arm/boot/dts/mt6589.dtsi index 41df742d7891..28df8495686a 100644 --- a/arch/arm/boot/dts/mt6589.dtsi +++ b/arch/arm/boot/dts/mt6589.dtsi @@ -1,17 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+ /* * Copyright (c) 2014 MundoReader S.L. * Author: Matthias Brugger <matthias.bgg@gmail.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - */ +*/ #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/arch/arm/boot/dts/mt6592-evb.dts b/arch/arm/boot/dts/mt6592-evb.dts index b57237e6394a..02849f6548e3 100644 --- a/arch/arm/boot/dts/mt6592-evb.dts +++ b/arch/arm/boot/dts/mt6592-evb.dts @@ -1,15 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2014 MediaTek Inc. * Author: Howard Chen <ibanezchen@gmail.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ /dts-v1/; diff --git a/arch/arm/boot/dts/mt6592.dtsi b/arch/arm/boot/dts/mt6592.dtsi index c69201ffff72..8696ac891d60 100644 --- a/arch/arm/boot/dts/mt6592.dtsi +++ b/arch/arm/boot/dts/mt6592.dtsi @@ -1,15 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2014 MediaTek Inc. * Author: Howard Chen <ibanezchen@gmail.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ #include <dt-bindings/interrupt-controller/irq.h> diff --git a/arch/arm/boot/dts/mt7623.dtsi b/arch/arm/boot/dts/mt7623.dtsi index e10c03496524..d1eb123bc73b 100644 --- a/arch/arm/boot/dts/mt7623.dtsi +++ b/arch/arm/boot/dts/mt7623.dtsi @@ -1,16 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0 /* - * Copyright (c) 2017 MediaTek Inc. + * Copyright (c) 2017-2018 MediaTek Inc. * Author: John Crispin <john@phrozen.org> * Sean Wang <sean.wang@mediatek.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ #include <dt-bindings/interrupt-controller/irq.h> @@ -22,11 +15,12 @@ #include <dt-bindings/phy/phy.h> #include <dt-bindings/reset/mt2701-resets.h> #include <dt-bindings/thermal/thermal.h> -#include "skeleton64.dtsi" / { compatible = "mediatek,mt7623"; interrupt-parent = <&sysirq>; + #address-cells = <2>; + #size-cells = <2>; cpu_opp_table: opp-table { compatible = "operating-points-v2"; @@ -130,14 +124,14 @@ #clock-cells = <0>; }; - rtc32k: oscillator@1 { + rtc32k: oscillator-1 { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <32000>; clock-output-names = "rtc32k"; }; - clk26m: oscillator@0 { + clk26m: oscillator-0 { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <26000000>; @@ -492,6 +486,18 @@ nvmem-cell-names = "calibration-data"; }; + btif: serial@1100c000 { + compatible = "mediatek,mt7623-btif", + "mediatek,mtk-btif"; + reg = <0 0x1100c000 0 0x1000>; + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_BTIF>; + clock-names = "main"; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + nandc: nfi@1100d000 { compatible = "mediatek,mt7623-nfc", "mediatek,mt2701-nfc"; @@ -517,6 +523,18 @@ status = "disabled"; }; + nor_flash: spi@11014000 { + compatible = "mediatek,mt7623-nor", + "mediatek,mt8173-nor"; + reg = <0 0x11014000 0 0x1000>; + clocks = <&pericfg CLK_PERI_FLASH>, + <&topckgen CLK_TOP_FLASH_SEL>; + clock-names = "spi", "sf"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + spi1: spi@11016000 { compatible = "mediatek,mt7623-spi", "mediatek,mt2701-spi"; @@ -545,105 +563,99 @@ status = "disabled"; }; - afe: audio-controller@11220000 { - compatible = "mediatek,mt7623-audio", - "mediatek,mt2701-audio"; - reg = <0 0x11220000 0 0x2000>, - <0 0x112a0000 0 0x20000>; - interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>; - interrupt-names = "afe", "asys"; - power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>; + audsys: clock-controller@11220000 { + compatible = "mediatek,mt7623-audsys", + "mediatek,mt2701-audsys", + "syscon"; + reg = <0 0x11220000 0 0x2000>; + #clock-cells = <1>; - clocks = <&infracfg CLK_INFRA_AUDIO>, - <&topckgen CLK_TOP_AUD_MUX1_SEL>, - <&topckgen CLK_TOP_AUD_MUX2_SEL>, - <&topckgen CLK_TOP_AUD_MUX1_DIV>, - <&topckgen CLK_TOP_AUD_MUX2_DIV>, - <&topckgen CLK_TOP_AUD_48K_TIMING>, - <&topckgen CLK_TOP_AUD_44K_TIMING>, - <&topckgen CLK_TOP_AUDPLL_MUX_SEL>, - <&topckgen CLK_TOP_APLL_SEL>, - <&topckgen CLK_TOP_AUD1PLL_98M>, - <&topckgen CLK_TOP_AUD2PLL_90M>, - <&topckgen CLK_TOP_HADDS2PLL_98M>, - <&topckgen CLK_TOP_HADDS2PLL_294M>, - <&topckgen CLK_TOP_AUDPLL>, - <&topckgen CLK_TOP_AUDPLL_D4>, - <&topckgen CLK_TOP_AUDPLL_D8>, - <&topckgen CLK_TOP_AUDPLL_D16>, - <&topckgen CLK_TOP_AUDPLL_D24>, - <&topckgen CLK_TOP_AUDINTBUS_SEL>, - <&clk26m>, - <&topckgen CLK_TOP_SYSPLL1_D4>, - <&topckgen CLK_TOP_AUD_K1_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K2_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K3_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K4_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K5_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K6_SRC_SEL>, - <&topckgen CLK_TOP_AUD_K1_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K2_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K3_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K4_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K5_SRC_DIV>, - <&topckgen CLK_TOP_AUD_K6_SRC_DIV>, - <&topckgen CLK_TOP_AUD_I2S1_MCLK>, - <&topckgen CLK_TOP_AUD_I2S2_MCLK>, - <&topckgen CLK_TOP_AUD_I2S3_MCLK>, - <&topckgen CLK_TOP_AUD_I2S4_MCLK>, - <&topckgen CLK_TOP_AUD_I2S5_MCLK>, - <&topckgen CLK_TOP_AUD_I2S6_MCLK>, - <&topckgen CLK_TOP_ASM_M_SEL>, - <&topckgen CLK_TOP_ASM_H_SEL>, - <&topckgen CLK_TOP_UNIVPLL2_D4>, - <&topckgen CLK_TOP_UNIVPLL2_D2>, - <&topckgen CLK_TOP_SYSPLL_D5>; - - clock-names = "infra_sys_audio_clk", - "top_audio_mux1_sel", - "top_audio_mux2_sel", - "top_audio_mux1_div", - "top_audio_mux2_div", - "top_audio_48k_timing", - "top_audio_44k_timing", - "top_audpll_mux_sel", - "top_apll_sel", - "top_aud1_pll_98M", - "top_aud2_pll_90M", - "top_hadds2_pll_98M", - "top_hadds2_pll_294M", - "top_audpll", - "top_audpll_d4", - "top_audpll_d8", - "top_audpll_d16", - "top_audpll_d24", - "top_audintbus_sel", - "clk_26m", - "top_syspll1_d4", - "top_aud_k1_src_sel", - "top_aud_k2_src_sel", - "top_aud_k3_src_sel", - "top_aud_k4_src_sel", - "top_aud_k5_src_sel", - "top_aud_k6_src_sel", - "top_aud_k1_src_div", - "top_aud_k2_src_div", - "top_aud_k3_src_div", - "top_aud_k4_src_div", - "top_aud_k5_src_div", - "top_aud_k6_src_div", - "top_aud_i2s1_mclk", - "top_aud_i2s2_mclk", - "top_aud_i2s3_mclk", - "top_aud_i2s4_mclk", - "top_aud_i2s5_mclk", - "top_aud_i2s6_mclk", - "top_asm_m_sel", - "top_asm_h_sel", - "top_univpll2_d4", - "top_univpll2_d2", - "top_syspll_d5"; + afe: audio-controller { + compatible = "mediatek,mt7623-audio", + "mediatek,mt2701-audio"; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "afe", "asys"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>; + + clocks = <&infracfg CLK_INFRA_AUDIO>, + <&topckgen CLK_TOP_AUD_MUX1_SEL>, + <&topckgen CLK_TOP_AUD_MUX2_SEL>, + <&topckgen CLK_TOP_AUD_48K_TIMING>, + <&topckgen CLK_TOP_AUD_44K_TIMING>, + <&topckgen CLK_TOP_AUD_K1_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K2_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K3_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K4_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K1_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K2_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K3_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K4_SRC_DIV>, + <&topckgen CLK_TOP_AUD_I2S1_MCLK>, + <&topckgen CLK_TOP_AUD_I2S2_MCLK>, + <&topckgen CLK_TOP_AUD_I2S3_MCLK>, + <&topckgen CLK_TOP_AUD_I2S4_MCLK>, + <&audsys CLK_AUD_I2SO1>, + <&audsys CLK_AUD_I2SO2>, + <&audsys CLK_AUD_I2SO3>, + <&audsys CLK_AUD_I2SO4>, + <&audsys CLK_AUD_I2SIN1>, + <&audsys CLK_AUD_I2SIN2>, + <&audsys CLK_AUD_I2SIN3>, + <&audsys CLK_AUD_I2SIN4>, + <&audsys CLK_AUD_ASRCO1>, + <&audsys CLK_AUD_ASRCO2>, + <&audsys CLK_AUD_ASRCO3>, + <&audsys CLK_AUD_ASRCO4>, + <&audsys CLK_AUD_AFE>, + <&audsys CLK_AUD_AFE_CONN>, + <&audsys CLK_AUD_A1SYS>, + <&audsys CLK_AUD_A2SYS>, + <&audsys CLK_AUD_AFE_MRGIF>; + + clock-names = "infra_sys_audio_clk", + "top_audio_mux1_sel", + "top_audio_mux2_sel", + "top_audio_a1sys_hp", + "top_audio_a2sys_hp", + "i2s0_src_sel", + "i2s1_src_sel", + "i2s2_src_sel", + "i2s3_src_sel", + "i2s0_src_div", + "i2s1_src_div", + "i2s2_src_div", + "i2s3_src_div", + "i2s0_mclk_en", + "i2s1_mclk_en", + "i2s2_mclk_en", + "i2s3_mclk_en", + "i2so0_hop_ck", + "i2so1_hop_ck", + "i2so2_hop_ck", + "i2so3_hop_ck", + "i2si0_hop_ck", + "i2si1_hop_ck", + "i2si2_hop_ck", + "i2si3_hop_ck", + "asrc0_out_ck", + "asrc1_out_ck", + "asrc2_out_ck", + "asrc3_out_ck", + "audio_afe_pd", + "audio_afe_conn_pd", + "audio_a1sys_pd", + "audio_a2sys_pd", + "audio_mrgif_pd"; + + assigned-clocks = <&topckgen CLK_TOP_AUD_MUX1_SEL>, + <&topckgen CLK_TOP_AUD_MUX2_SEL>, + <&topckgen CLK_TOP_AUD_MUX1_DIV>, + <&topckgen CLK_TOP_AUD_MUX2_DIV>; + assigned-clock-parents = <&topckgen CLK_TOP_AUD1PLL_98M>, + <&topckgen CLK_TOP_AUD2PLL_90M>; + assigned-clock-rates = <0>, <0>, <49152000>, <45158400>; + }; }; mmc0: mmc@11230000 { @@ -873,6 +885,16 @@ #reset-cells = <1>; }; + hsdma: dma-controller@1b007000 { + compatible = "mediatek,mt7623-hsdma"; + reg = <0 0x1b007000 0 0x1000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_LOW>; + clocks = <ðsys CLK_ETHSYS_HSDMA>; + clock-names = "hsdma"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>; + #dma-cells = <1>; + }; + eth: ethernet@1b100000 { compatible = "mediatek,mt7623-eth", "mediatek,mt2701-eth", @@ -913,3 +935,298 @@ status = "disabled"; }; }; + +&pio { + cir_pins_a:cir-default { + pins-cir { + pinmux = <MT7623_PIN_46_IR_FUNC_IR>; + bias-disable; + }; + }; + + i2c0_pins_a: i2c0-default { + pins-i2c0 { + pinmux = <MT7623_PIN_75_SDA0_FUNC_SDA0>, + <MT7623_PIN_76_SCL0_FUNC_SCL0>; + bias-disable; + }; + }; + + i2c1_pins_a: i2c1-default { + pin-i2c1 { + pinmux = <MT7623_PIN_57_SDA1_FUNC_SDA1>, + <MT7623_PIN_58_SCL1_FUNC_SCL1>; + bias-disable; + }; + }; + + i2c1_pins_b: i2c1-alt { + pin-i2c1 { + pinmux = <MT7623_PIN_242_URTS2_FUNC_SCL1>, + <MT7623_PIN_243_UCTS2_FUNC_SDA1>; + bias-disable; + }; + }; + + i2c2_pins_a: i2c2-default { + pin-i2c2 { + pinmux = <MT7623_PIN_77_SDA2_FUNC_SDA2>, + <MT7623_PIN_78_SCL2_FUNC_SCL2>; + bias-disable; + }; + }; + + i2c2_pins_b: i2c2-alt { + pin-i2c2 { + pinmux = <MT7623_PIN_122_GPIO122_FUNC_SDA2>, + <MT7623_PIN_123_HTPLG_FUNC_SCL2>; + bias-disable; + }; + }; + + i2s0_pins_a: i2s0-default { + pin-i2s0 { + pinmux = <MT7623_PIN_49_I2S0_DATA_FUNC_I2S0_DATA>, + <MT7623_PIN_72_I2S0_DATA_IN_FUNC_I2S0_DATA_IN>, + <MT7623_PIN_73_I2S0_LRCK_FUNC_I2S0_LRCK>, + <MT7623_PIN_74_I2S0_BCK_FUNC_I2S0_BCK>, + <MT7623_PIN_126_I2S0_MCLK_FUNC_I2S0_MCLK>; + drive-strength = <MTK_DRIVE_12mA>; + bias-pull-down; + }; + }; + + i2s1_pins_a: i2s1-default { + pin-i2s1 { + pinmux = <MT7623_PIN_33_I2S1_DATA_FUNC_I2S1_DATA>, + <MT7623_PIN_34_I2S1_DATA_IN_FUNC_I2S1_DATA_IN>, + <MT7623_PIN_35_I2S1_BCK_FUNC_I2S1_BCK>, + <MT7623_PIN_36_I2S1_LRCK_FUNC_I2S1_LRCK>, + <MT7623_PIN_37_I2S1_MCLK_FUNC_I2S1_MCLK>; + drive-strength = <MTK_DRIVE_12mA>; + bias-pull-down; + }; + }; + + key_pins_a: keys-alt { + pins-keys { + pinmux = <MT7623_PIN_256_GPIO256_FUNC_GPIO256>, + <MT7623_PIN_257_GPIO257_FUNC_GPIO257> ; + input-enable; + }; + }; + + led_pins_a: leds-alt { + pins-leds { + pinmux = <MT7623_PIN_239_EXT_SDIO0_FUNC_GPIO239>, + <MT7623_PIN_240_EXT_XCS_FUNC_GPIO240>, + <MT7623_PIN_241_EXT_SCK_FUNC_GPIO241>; + }; + }; + + mmc0_pins_default: mmc0default { + pins-cmd-dat { + pinmux = <MT7623_PIN_111_MSDC0_DAT7_FUNC_MSDC0_DAT7>, + <MT7623_PIN_112_MSDC0_DAT6_FUNC_MSDC0_DAT6>, + <MT7623_PIN_113_MSDC0_DAT5_FUNC_MSDC0_DAT5>, + <MT7623_PIN_114_MSDC0_DAT4_FUNC_MSDC0_DAT4>, + <MT7623_PIN_118_MSDC0_DAT3_FUNC_MSDC0_DAT3>, + <MT7623_PIN_119_MSDC0_DAT2_FUNC_MSDC0_DAT2>, + <MT7623_PIN_120_MSDC0_DAT1_FUNC_MSDC0_DAT1>, + <MT7623_PIN_121_MSDC0_DAT0_FUNC_MSDC0_DAT0>, + <MT7623_PIN_116_MSDC0_CMD_FUNC_MSDC0_CMD>; + input-enable; + bias-pull-up; + }; + + pins-clk { + pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_MSDC0_CLK>; + bias-pull-down; + }; + + pins-rst { + pinmux = <MT7623_PIN_115_MSDC0_RSTB_FUNC_MSDC0_RSTB>; + bias-pull-up; + }; + }; + + mmc0_pins_uhs: mmc0 { + pins-cmd-dat { + pinmux = <MT7623_PIN_111_MSDC0_DAT7_FUNC_MSDC0_DAT7>, + <MT7623_PIN_112_MSDC0_DAT6_FUNC_MSDC0_DAT6>, + <MT7623_PIN_113_MSDC0_DAT5_FUNC_MSDC0_DAT5>, + <MT7623_PIN_114_MSDC0_DAT4_FUNC_MSDC0_DAT4>, + <MT7623_PIN_118_MSDC0_DAT3_FUNC_MSDC0_DAT3>, + <MT7623_PIN_119_MSDC0_DAT2_FUNC_MSDC0_DAT2>, + <MT7623_PIN_120_MSDC0_DAT1_FUNC_MSDC0_DAT1>, + <MT7623_PIN_121_MSDC0_DAT0_FUNC_MSDC0_DAT0>, + <MT7623_PIN_116_MSDC0_CMD_FUNC_MSDC0_CMD>; + input-enable; + drive-strength = <MTK_DRIVE_2mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + + pins-clk { + pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_MSDC0_CLK>; + drive-strength = <MTK_DRIVE_2mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_01>; + }; + + pins-rst { + pinmux = <MT7623_PIN_115_MSDC0_RSTB_FUNC_MSDC0_RSTB>; + bias-pull-up; + }; + }; + + mmc1_pins_default: mmc1default { + pins-cmd-dat { + pinmux = <MT7623_PIN_107_MSDC1_DAT0_FUNC_MSDC1_DAT0>, + <MT7623_PIN_108_MSDC1_DAT1_FUNC_MSDC1_DAT1>, + <MT7623_PIN_109_MSDC1_DAT2_FUNC_MSDC1_DAT2>, + <MT7623_PIN_110_MSDC1_DAT3_FUNC_MSDC1_DAT3>, + <MT7623_PIN_105_MSDC1_CMD_FUNC_MSDC1_CMD>; + input-enable; + drive-strength = <MTK_DRIVE_4mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_10>; + }; + + pins-clk { + pinmux = <MT7623_PIN_106_MSDC1_CLK_FUNC_MSDC1_CLK>; + bias-pull-down; + drive-strength = <MTK_DRIVE_4mA>; + }; + + pins-wp { + pinmux = <MT7623_PIN_29_EINT7_FUNC_MSDC1_WP>; + input-enable; + bias-pull-up; + }; + + pins-insert { + pinmux = <MT7623_PIN_261_MSDC1_INS_FUNC_GPIO261>; + bias-pull-up; + }; + }; + + mmc1_pins_uhs: mmc1 { + pins-cmd-dat { + pinmux = <MT7623_PIN_107_MSDC1_DAT0_FUNC_MSDC1_DAT0>, + <MT7623_PIN_108_MSDC1_DAT1_FUNC_MSDC1_DAT1>, + <MT7623_PIN_109_MSDC1_DAT2_FUNC_MSDC1_DAT2>, + <MT7623_PIN_110_MSDC1_DAT3_FUNC_MSDC1_DAT3>, + <MT7623_PIN_105_MSDC1_CMD_FUNC_MSDC1_CMD>; + input-enable; + drive-strength = <MTK_DRIVE_4mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_10>; + }; + + pins-clk { + pinmux = <MT7623_PIN_106_MSDC1_CLK_FUNC_MSDC1_CLK>; + drive-strength = <MTK_DRIVE_4mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + }; + + nand_pins_default: nanddefault { + pins-ale { + pinmux = <MT7623_PIN_116_MSDC0_CMD_FUNC_NALE>; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + pins-dat { + pinmux = <MT7623_PIN_111_MSDC0_DAT7_FUNC_NLD7>, + <MT7623_PIN_112_MSDC0_DAT6_FUNC_NLD6>, + <MT7623_PIN_114_MSDC0_DAT4_FUNC_NLD4>, + <MT7623_PIN_118_MSDC0_DAT3_FUNC_NLD3>, + <MT7623_PIN_121_MSDC0_DAT0_FUNC_NLD0>, + <MT7623_PIN_120_MSDC0_DAT1_FUNC_NLD1>, + <MT7623_PIN_113_MSDC0_DAT5_FUNC_NLD5>, + <MT7623_PIN_115_MSDC0_RSTB_FUNC_NLD8>, + <MT7623_PIN_119_MSDC0_DAT2_FUNC_NLD2>; + input-enable; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-up; + }; + + pins-we { + pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_NWEB>; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_10>; + }; + }; + + pcie_default: pcie_pin_default { + pins_cmd_dat { + pinmux = <MT7623_PIN_208_AUD_EXT_CK1_FUNC_PCIE0_PERST_N>, + <MT7623_PIN_209_AUD_EXT_CK2_FUNC_PCIE1_PERST_N>; + bias-disable; + }; + }; + + pwm_pins_a: pwm-default { + pins-pwm { + pinmux = <MT7623_PIN_203_PWM0_FUNC_PWM0>, + <MT7623_PIN_204_PWM1_FUNC_PWM1>, + <MT7623_PIN_205_PWM2_FUNC_PWM2>, + <MT7623_PIN_206_PWM3_FUNC_PWM3>, + <MT7623_PIN_207_PWM4_FUNC_PWM4>; + }; + }; + + spi0_pins_a: spi0-default { + pins-spi { + pinmux = <MT7623_PIN_53_SPI0_CSN_FUNC_SPI0_CS>, + <MT7623_PIN_54_SPI0_CK_FUNC_SPI0_CK>, + <MT7623_PIN_55_SPI0_MI_FUNC_SPI0_MI>, + <MT7623_PIN_56_SPI0_MO_FUNC_SPI0_MO>; + bias-disable; + }; + }; + + spi1_pins_a: spi1-default { + pins-spi { + pinmux = <MT7623_PIN_7_SPI1_CSN_FUNC_SPI1_CS>, + <MT7623_PIN_199_SPI1_CK_FUNC_SPI1_CK>, + <MT7623_PIN_8_SPI1_MI_FUNC_SPI1_MI>, + <MT7623_PIN_9_SPI1_MO_FUNC_SPI1_MO>; + }; + }; + + spi2_pins_a: spi2-default { + pins-spi { + pinmux = <MT7623_PIN_101_SPI2_CSN_FUNC_SPI2_CS>, + <MT7623_PIN_104_SPI2_CK_FUNC_SPI2_CK>, + <MT7623_PIN_102_SPI2_MI_FUNC_SPI2_MI>, + <MT7623_PIN_103_SPI2_MO_FUNC_SPI2_MO>; + }; + }; + + uart0_pins_a: uart0-default { + pins-dat { + pinmux = <MT7623_PIN_79_URXD0_FUNC_URXD0>, + <MT7623_PIN_80_UTXD0_FUNC_UTXD0>; + }; + }; + + uart1_pins_a: uart1-default { + pins-dat { + pinmux = <MT7623_PIN_81_URXD1_FUNC_URXD1>, + <MT7623_PIN_82_UTXD1_FUNC_UTXD1>; + }; + }; + + uart2_pins_a: uart2-default { + pins-dat { + pinmux = <MT7623_PIN_14_GPIO14_FUNC_URXD2>, + <MT7623_PIN_15_GPIO15_FUNC_UTXD2>; + }; + }; + + uart2_pins_b: uart2-alt { + pins-dat { + pinmux = <MT7623_PIN_200_URXD2_FUNC_URXD2>, + <MT7623_PIN_201_UTXD2_FUNC_UTXD2>; + }; + }; +}; diff --git a/arch/arm/boot/dts/mt7623a-rfb-emmc.dts b/arch/arm/boot/dts/mt7623a-rfb-emmc.dts new file mode 100644 index 000000000000..13c86936d1c8 --- /dev/null +++ b/arch/arm/boot/dts/mt7623a-rfb-emmc.dts @@ -0,0 +1,291 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2017-2018 MediaTek Inc. + * Author: Sean Wang <sean.wang@mediatek.com> + * + */ + +/dts-v1/; +#include <dt-bindings/input/input.h> +#include "mt7623a.dtsi" +#include "mt6323.dtsi" + +/ { + model = "MediaTek MT7623A with eMMC reference board"; + compatible = "mediatek,mt7623a-rfb-emmc", "mediatek,mt7623"; + + aliases { + serial2 = &uart2; + }; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + cpus { + cpu@0 { + proc-supply = <&mt6323_vproc_reg>; + }; + + cpu@1 { + proc-supply = <&mt6323_vproc_reg>; + }; + + cpu@2 { + proc-supply = <&mt6323_vproc_reg>; + }; + + cpu@3 { + proc-supply = <&mt6323_vproc_reg>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&key_pins_a>; + + factory { + label = "factory"; + linux,code = <BTN_0>; + gpios = <&pio 256 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&pio 257 GPIO_ACTIVE_HIGH>; + }; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0 0x80000000 0 0x20000000>; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "fixed-1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "fixed-5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + sound { + compatible = "mediatek,mt2701-wm8960-machine"; + mediatek,platform = <&afe>; + audio-routing = + "Headphone", "HP_L", + "Headphone", "HP_R", + "LINPUT1", "AMIC", + "RINPUT1", "AMIC"; + mediatek,audio-codec = <&wm8960>; + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_pins_a>; + }; +}; + +&btif { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + + mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + switch@0 { + compatible = "mediatek,mt7530"; + reg = <0>; + mediatek,mcm; + resets = <ðsys MT2701_ETHSYS_MCM_RST>; + reset-names = "mcm"; + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_b>; + status = "okay"; + + wm8960: wm8960@1a { + compatible = "wlf,wm8960"; + reg = <0x1a>; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_b>; + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_default>; + pinctrl-1 = <&mmc0_pins_uhs>; + status = "okay"; + bus-width = <8>; + max-frequency = <50000000>; + cap-mmc-highspeed; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_1p8v>; + non-removable; +}; + +&mmc1 { + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc1_pins_default>; + pinctrl-1 = <&mmc1_pins_uhs>; + status = "okay"; + bus-width = <4>; + max-frequency = <50000000>; + cap-sd-highspeed; + cd-gpios = <&pio 261 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_3p3v>; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pcie_default>; + status = "okay"; + + pcie@0,0 { + status = "okay"; + }; + + pcie@1,0 { + status = "okay"; + }; +}; + +&pcie0_phy { + status = "okay"; +}; + +&pcie1_phy { + status = "okay"; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pins_a>; + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins_a>; + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins_a>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins_b>; + status = "okay"; +}; + +&usb1 { + vusb33-supply = <®_3p3v>; + vbus-supply = <®_5v>; + status = "okay"; +}; + +&u3phy1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/mt7623a-rfb-nand.dts b/arch/arm/boot/dts/mt7623a-rfb-nand.dts new file mode 100644 index 000000000000..88d8f0b2f4c2 --- /dev/null +++ b/arch/arm/boot/dts/mt7623a-rfb-nand.dts @@ -0,0 +1,337 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2017-2018 MediaTek Inc. + * Author: Sean Wang <sean.wang@mediatek.com> + * + */ + +/dts-v1/; +#include <dt-bindings/input/input.h> +#include "mt7623a.dtsi" +#include "mt6323.dtsi" + +/ { + model = "MediaTek MT7623A with NAND reference board"; + compatible = "mediatek,mt7623a-rfb-nand", "mediatek,mt7623"; + + aliases { + serial2 = &uart2; + }; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + cpus { + cpu@0 { + proc-supply = <&mt6323_vproc_reg>; + }; + + cpu@1 { + proc-supply = <&mt6323_vproc_reg>; + }; + + cpu@2 { + proc-supply = <&mt6323_vproc_reg>; + }; + + cpu@3 { + proc-supply = <&mt6323_vproc_reg>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&key_pins_a>; + + factory { + label = "factory"; + linux,code = <BTN_0>; + gpios = <&pio 256 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&pio 257 GPIO_ACTIVE_HIGH>; + }; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0 0x80000000 0 0x20000000>; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "fixed-1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "fixed-5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + sound { + compatible = "mediatek,mt2701-wm8960-machine"; + mediatek,platform = <&afe>; + audio-routing = + "Headphone", "HP_L", + "Headphone", "HP_R", + "LINPUT1", "AMIC", + "RINPUT1", "AMIC"; + mediatek,audio-codec = <&wm8960>; + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_pins_a>; + }; +}; + +&bch { + status = "okay"; +}; + +&btif { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + + mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + switch@0 { + compatible = "mediatek,mt7530"; + reg = <0>; + mediatek,mcm; + resets = <ðsys MT2701_ETHSYS_MCM_RST>; + reset-names = "mcm"; + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_b>; + status = "okay"; + + wm8960: wm8960@1a { + compatible = "wlf,wm8960"; + reg = <0x1a>; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_b>; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc1_pins_default>; + pinctrl-1 = <&mmc1_pins_uhs>; + status = "okay"; + bus-width = <4>; + max-frequency = <50000000>; + cap-sd-highspeed; + cd-gpios = <&pio 261 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_3p3v>; +}; + +&nandc { + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins_default>; + status = "okay"; + + nand@0 { + reg = <0>; + spare_per_sector = <64>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <12>; + nand-ecc-step-size = <1024>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "preloader"; + reg = <0x0 0x40000>; + }; + + partition@40000 { + label = "uboot"; + reg = <0x40000 0x80000>; + }; + + partition@c0000 { + label = "uboot-env"; + reg = <0xC0000 0x40000>; + }; + + partition@140000 { + label = "bootimg"; + reg = <0x140000 0x2000000>; + }; + + partition@2140000 { + label = "recovery"; + reg = <0x2140000 0x2000000>; + }; + + partition@4140000 { + label = "rootfs"; + reg = <0x4140000 0x1000000>; + }; + + partition@5140000 { + label = "usrdata"; + reg = <0x5140000 0x1000000>; + }; + }; + }; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pcie_default>; + status = "okay"; + + pcie@0,0 { + status = "okay"; + }; + + pcie@1,0 { + status = "okay"; + }; +}; + +&pcie0_phy { + status = "okay"; +}; + +&pcie1_phy { + status = "okay"; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pins_a>; + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins_a>; + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins_a>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins_b>; + status = "okay"; +}; + +&usb1 { + vusb33-supply = <®_3p3v>; + vbus-supply = <®_5v>; + status = "okay"; +}; + +&u3phy1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/mt7623a.dtsi b/arch/arm/boot/dts/mt7623a.dtsi new file mode 100644 index 000000000000..0735a1fb8ad9 --- /dev/null +++ b/arch/arm/boot/dts/mt7623a.dtsi @@ -0,0 +1,44 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2017-2018 MediaTek Inc. + * Author: Sean Wang <sean.wang@mediatek.com> + * + */ + +/dts-v1/; +#include <dt-bindings/power/mt7623a-power.h> +#include "mt7623.dtsi" + +&afe { + power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>; +}; + +&crypto { + power-domains = <&scpsys MT7623A_POWER_DOMAIN_ETH>; +}; + +ð { + power-domains = <&scpsys MT7623A_POWER_DOMAIN_ETH>; +}; + +&nandc { + power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>; +}; + +&pcie { + power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>; +}; + +&scpsys { + compatible = "mediatek,mt7623a-scpsys"; + clocks = <&topckgen CLK_TOP_ETHIF_SEL>; + clock-names = "ethif"; +}; + +&usb1 { + power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>; +}; + +&usb2 { + power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>; +}; diff --git a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts index bbf56f855e46..531d905d924f 100644 --- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts +++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts @@ -1,5 +1,5 @@ /* - * Copyright 2017 Sean Wang <sean.wang@mediatek.com> + * Copyright 2017-2018 Sean Wang <sean.wang@mediatek.com> * * SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ @@ -109,10 +109,15 @@ }; memory@80000000 { - reg = <0 0x80000000 0 0x40000000>; + device_type = "memory"; + reg = <0 0x80000000 0 0x80000000>; }; }; +&btif { + status = "okay"; +}; + &cir { pinctrl-names = "default"; pinctrl-0 = <&cir_pins_a>; @@ -144,8 +149,6 @@ switch@0 { compatible = "mediatek,mt7530"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; reset-gpios = <&pio 33 0>; core-supply = <&mt6323_vpa_reg>; @@ -154,7 +157,6 @@ ports { #address-cells = <1>; #size-cells = <0>; - reg = <0>; port@0 { reg = <0>; @@ -235,6 +237,28 @@ vqmmc-supply = <®_3p3v>; }; +&mt6323_leds { + status = "okay"; + + led@0 { + reg = <0>; + label = "bpi-r2:isink:green"; + default-state = "off"; + }; + + led@1 { + reg = <1>; + label = "bpi-r2:isink:red"; + default-state = "off"; + }; + + led@2 { + reg = <2>; + label = "bpi-r2:isink:blue"; + default-state = "off"; + }; +}; + &pcie { pinctrl-names = "default"; pinctrl-0 = <&pcie_default>; @@ -257,257 +281,12 @@ status = "okay"; }; -&pio { - cir_pins_a:cir@0 { - pins-cir { - pinmux = <MT7623_PIN_46_IR_FUNC_IR>; - bias-disable; - }; - }; - - i2c0_pins_a: i2c@0 { - pins-i2c0 { - pinmux = <MT7623_PIN_75_SDA0_FUNC_SDA0>, - <MT7623_PIN_76_SCL0_FUNC_SCL0>; - bias-disable; - }; - }; - - i2c1_pins_a: i2c@1 { - pin-i2c1 { - pinmux = <MT7623_PIN_57_SDA1_FUNC_SDA1>, - <MT7623_PIN_58_SCL1_FUNC_SCL1>; - bias-disable; - }; - }; - - i2s0_pins_a: i2s@0 { - pin-i2s0 { - pinmux = <MT7623_PIN_49_I2S0_DATA_FUNC_I2S0_DATA>, - <MT7623_PIN_72_I2S0_DATA_IN_FUNC_I2S0_DATA_IN>, - <MT7623_PIN_73_I2S0_LRCK_FUNC_I2S0_LRCK>, - <MT7623_PIN_74_I2S0_BCK_FUNC_I2S0_BCK>, - <MT7623_PIN_126_I2S0_MCLK_FUNC_I2S0_MCLK>; - drive-strength = <MTK_DRIVE_12mA>; - bias-pull-down; - }; - }; - - i2s1_pins_a: i2s@1 { - pin-i2s1 { - pinmux = <MT7623_PIN_33_I2S1_DATA_FUNC_I2S1_DATA>, - <MT7623_PIN_34_I2S1_DATA_IN_FUNC_I2S1_DATA_IN>, - <MT7623_PIN_35_I2S1_BCK_FUNC_I2S1_BCK>, - <MT7623_PIN_36_I2S1_LRCK_FUNC_I2S1_LRCK>, - <MT7623_PIN_37_I2S1_MCLK_FUNC_I2S1_MCLK>; - drive-strength = <MTK_DRIVE_12mA>; - bias-pull-down; - }; - }; - - key_pins_a: keys@0 { - pins-keys { - pinmux = <MT7623_PIN_256_GPIO256_FUNC_GPIO256>, - <MT7623_PIN_257_GPIO257_FUNC_GPIO257> ; - input-enable; - }; - }; - - led_pins_a: leds@0 { - pins-leds { - pinmux = <MT7623_PIN_239_EXT_SDIO0_FUNC_GPIO239>, - <MT7623_PIN_240_EXT_XCS_FUNC_GPIO240>, - <MT7623_PIN_241_EXT_SCK_FUNC_GPIO241>; - }; - }; - - mmc0_pins_default: mmc0default { - pins-cmd-dat { - pinmux = <MT7623_PIN_111_MSDC0_DAT7_FUNC_MSDC0_DAT7>, - <MT7623_PIN_112_MSDC0_DAT6_FUNC_MSDC0_DAT6>, - <MT7623_PIN_113_MSDC0_DAT5_FUNC_MSDC0_DAT5>, - <MT7623_PIN_114_MSDC0_DAT4_FUNC_MSDC0_DAT4>, - <MT7623_PIN_118_MSDC0_DAT3_FUNC_MSDC0_DAT3>, - <MT7623_PIN_119_MSDC0_DAT2_FUNC_MSDC0_DAT2>, - <MT7623_PIN_120_MSDC0_DAT1_FUNC_MSDC0_DAT1>, - <MT7623_PIN_121_MSDC0_DAT0_FUNC_MSDC0_DAT0>, - <MT7623_PIN_116_MSDC0_CMD_FUNC_MSDC0_CMD>; - input-enable; - bias-pull-up; - }; - - pins-clk { - pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_MSDC0_CLK>; - bias-pull-down; - }; - - pins-rst { - pinmux = <MT7623_PIN_115_MSDC0_RSTB_FUNC_MSDC0_RSTB>; - bias-pull-up; - }; - }; - - mmc0_pins_uhs: mmc0 { - pins-cmd-dat { - pinmux = <MT7623_PIN_111_MSDC0_DAT7_FUNC_MSDC0_DAT7>, - <MT7623_PIN_112_MSDC0_DAT6_FUNC_MSDC0_DAT6>, - <MT7623_PIN_113_MSDC0_DAT5_FUNC_MSDC0_DAT5>, - <MT7623_PIN_114_MSDC0_DAT4_FUNC_MSDC0_DAT4>, - <MT7623_PIN_118_MSDC0_DAT3_FUNC_MSDC0_DAT3>, - <MT7623_PIN_119_MSDC0_DAT2_FUNC_MSDC0_DAT2>, - <MT7623_PIN_120_MSDC0_DAT1_FUNC_MSDC0_DAT1>, - <MT7623_PIN_121_MSDC0_DAT0_FUNC_MSDC0_DAT0>, - <MT7623_PIN_116_MSDC0_CMD_FUNC_MSDC0_CMD>; - input-enable; - drive-strength = <MTK_DRIVE_2mA>; - bias-pull-up = <MTK_PUPD_SET_R1R0_01>; - }; - - pins-clk { - pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_MSDC0_CLK>; - drive-strength = <MTK_DRIVE_2mA>; - bias-pull-down = <MTK_PUPD_SET_R1R0_01>; - }; - - pins-rst { - pinmux = <MT7623_PIN_115_MSDC0_RSTB_FUNC_MSDC0_RSTB>; - bias-pull-up; - }; - }; - - mmc1_pins_default: mmc1default { - pins-cmd-dat { - pinmux = <MT7623_PIN_107_MSDC1_DAT0_FUNC_MSDC1_DAT0>, - <MT7623_PIN_108_MSDC1_DAT1_FUNC_MSDC1_DAT1>, - <MT7623_PIN_109_MSDC1_DAT2_FUNC_MSDC1_DAT2>, - <MT7623_PIN_110_MSDC1_DAT3_FUNC_MSDC1_DAT3>, - <MT7623_PIN_105_MSDC1_CMD_FUNC_MSDC1_CMD>; - input-enable; - drive-strength = <MTK_DRIVE_4mA>; - bias-pull-up = <MTK_PUPD_SET_R1R0_10>; - }; - - pins-clk { - pinmux = <MT7623_PIN_106_MSDC1_CLK_FUNC_MSDC1_CLK>; - bias-pull-down; - drive-strength = <MTK_DRIVE_4mA>; - }; - - pins-wp { - pinmux = <MT7623_PIN_29_EINT7_FUNC_MSDC1_WP>; - input-enable; - bias-pull-up; - }; - - pins-insert { - pinmux = <MT7623_PIN_261_MSDC1_INS_FUNC_GPIO261>; - bias-pull-up; - }; - }; - - mmc1_pins_uhs: mmc1 { - pins-cmd-dat { - pinmux = <MT7623_PIN_107_MSDC1_DAT0_FUNC_MSDC1_DAT0>, - <MT7623_PIN_108_MSDC1_DAT1_FUNC_MSDC1_DAT1>, - <MT7623_PIN_109_MSDC1_DAT2_FUNC_MSDC1_DAT2>, - <MT7623_PIN_110_MSDC1_DAT3_FUNC_MSDC1_DAT3>, - <MT7623_PIN_105_MSDC1_CMD_FUNC_MSDC1_CMD>; - input-enable; - drive-strength = <MTK_DRIVE_4mA>; - bias-pull-up = <MTK_PUPD_SET_R1R0_10>; - }; - - pins-clk { - pinmux = <MT7623_PIN_106_MSDC1_CLK_FUNC_MSDC1_CLK>; - drive-strength = <MTK_DRIVE_4mA>; - bias-pull-down = <MTK_PUPD_SET_R1R0_10>; - }; - }; - - pcie_default: pcie_pin_default { - pins_cmd_dat { - pinmux = <MT7623_PIN_208_AUD_EXT_CK1_FUNC_PCIE0_PERST_N>, - <MT7623_PIN_209_AUD_EXT_CK2_FUNC_PCIE1_PERST_N>; - bias-disable; - }; - }; - - pwm_pins_a: pwm@0 { - pins-pwm { - pinmux = <MT7623_PIN_203_PWM0_FUNC_PWM0>, - <MT7623_PIN_204_PWM1_FUNC_PWM1>, - <MT7623_PIN_205_PWM2_FUNC_PWM2>, - <MT7623_PIN_206_PWM3_FUNC_PWM3>, - <MT7623_PIN_207_PWM4_FUNC_PWM4>; - }; - }; - - spi0_pins_a: spi@0 { - pins-spi { - pinmux = <MT7623_PIN_53_SPI0_CSN_FUNC_SPI0_CS>, - <MT7623_PIN_54_SPI0_CK_FUNC_SPI0_CK>, - <MT7623_PIN_55_SPI0_MI_FUNC_SPI0_MI>, - <MT7623_PIN_56_SPI0_MO_FUNC_SPI0_MO>; - bias-disable; - }; - }; - - uart0_pins_a: uart@0 { - pins-dat { - pinmux = <MT7623_PIN_79_URXD0_FUNC_URXD0>, - <MT7623_PIN_80_UTXD0_FUNC_UTXD0>; - }; - }; - - uart1_pins_a: uart@1 { - pins-dat { - pinmux = <MT7623_PIN_81_URXD1_FUNC_URXD1>, - <MT7623_PIN_82_UTXD1_FUNC_UTXD1>; - }; - }; - - uart2_pins_a: uart@2 { - pins-dat { - pinmux = <MT7623_PIN_14_GPIO14_FUNC_URXD2>, - <MT7623_PIN_15_GPIO15_FUNC_UTXD2>; - }; - }; -}; - &pwm { pinctrl-names = "default"; pinctrl-0 = <&pwm_pins_a>; status = "okay"; }; -&pwrap { - mt6323 { - mt6323led: led { - compatible = "mediatek,mt6323-led"; - #address-cells = <1>; - #size-cells = <0>; - - led@0 { - reg = <0>; - label = "bpi-r2:isink:green"; - default-state = "off"; - }; - - led@1 { - reg = <1>; - label = "bpi-r2:isink:red"; - default-state = "off"; - }; - - led@2 { - reg = <2>; - label = "bpi-r2:isink:blue"; - default-state = "off"; - }; - }; - }; -}; - &spi0 { pinctrl-names = "default"; pinctrl-0 = <&spi0_pins_a>; diff --git a/arch/arm/boot/dts/mt7623n-rfb-emmc.dts b/arch/arm/boot/dts/mt7623n-rfb-emmc.dts new file mode 100644 index 000000000000..b7606130ade9 --- /dev/null +++ b/arch/arm/boot/dts/mt7623n-rfb-emmc.dts @@ -0,0 +1,326 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2017-2018 MediaTek Inc. + * Author: Sean Wang <sean.wang@mediatek.com> + * + */ + +/dts-v1/; +#include <dt-bindings/input/input.h> +#include "mt7623.dtsi" +#include "mt6323.dtsi" + +/ { + model = "MediaTek MT7623N with eMMC reference board"; + compatible = "mediatek,mt7623n-rfb-emmc", "mediatek,mt7623"; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + }; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + cpus { + cpu@0 { + proc-supply = <&mt6323_vproc_reg>; + }; + + cpu@1 { + proc-supply = <&mt6323_vproc_reg>; + }; + + cpu@2 { + proc-supply = <&mt6323_vproc_reg>; + }; + + cpu@3 { + proc-supply = <&mt6323_vproc_reg>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&key_pins_a>; + + factory { + label = "factory"; + linux,code = <BTN_0>; + gpios = <&pio 256 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&pio 257 GPIO_ACTIVE_HIGH>; + }; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0 0x80000000 0 0x40000000>; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "fixed-1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "fixed-5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + sound { + compatible = "mediatek,mt2701-wm8960-machine"; + mediatek,platform = <&afe>; + audio-routing = + "Headphone", "HP_L", + "Headphone", "HP_R", + "LINPUT1", "AMIC", + "RINPUT1", "AMIC"; + mediatek,audio-codec = <&wm8960>; + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_pins_a>; + }; +}; + +&btif { + status = "okay"; +}; + +&cir { + pinctrl-names = "default"; + pinctrl-0 = <&cir_pins_a>; + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + + mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-handle = <&phy5>; + }; + + mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + phy5: ethernet-phy@5 { + reg = <5>; + phy-mode = "rgmii-rxid"; + }; + + switch@0 { + compatible = "mediatek,mt7530"; + reg = <0>; + reset-gpios = <&pio 33 0>; + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_b>; + status = "okay"; + + wm8960: wm8960@1a { + compatible = "wlf,wm8960"; + reg = <0x1a>; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_default>; + pinctrl-1 = <&mmc0_pins_uhs>; + status = "okay"; + bus-width = <8>; + max-frequency = <50000000>; + cap-mmc-highspeed; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_1p8v>; + non-removable; +}; + +&mmc1 { + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc1_pins_default>; + pinctrl-1 = <&mmc1_pins_uhs>; + status = "okay"; + bus-width = <4>; + max-frequency = <50000000>; + cap-sd-highspeed; + cd-gpios = <&pio 261 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_3p3v>; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pcie_default>; + status = "okay"; + + pcie@0,0 { + status = "okay"; + }; + + pcie@1,0 { + status = "okay"; + }; +}; + +&pcie0_phy { + status = "okay"; +}; + +&pcie1_phy { + status = "okay"; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pins_a>; + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins_a>; + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins_a>; + status = "okay"; +}; + +&spi2 { + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins_a>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins_a>; + status = "okay"; +}; + +&usb1 { + vusb33-supply = <®_3p3v>; + vbus-supply = <®_5v>; + status = "okay"; +}; + +&u3phy1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/mt7623n-rfb-nand.dts b/arch/arm/boot/dts/mt7623n-rfb-nand.dts index f729c718aba1..96ff3c9068ae 100644 --- a/arch/arm/boot/dts/mt7623n-rfb-nand.dts +++ b/arch/arm/boot/dts/mt7623n-rfb-nand.dts @@ -1,15 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2017 MediaTek Inc. * Author: John Crispin <john@phrozen.org> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ /dts-v1/; @@ -78,34 +71,3 @@ }; }; }; - -&pio { - nand_pins_default: nanddefault { - pins-ale { - pinmux = <MT7623_PIN_116_MSDC0_CMD_FUNC_NALE>; - drive-strength = <MTK_DRIVE_8mA>; - bias-pull-down = <MTK_PUPD_SET_R1R0_10>; - }; - - pins-dat { - pinmux = <MT7623_PIN_111_MSDC0_DAT7_FUNC_NLD7>, - <MT7623_PIN_112_MSDC0_DAT6_FUNC_NLD6>, - <MT7623_PIN_114_MSDC0_DAT4_FUNC_NLD4>, - <MT7623_PIN_118_MSDC0_DAT3_FUNC_NLD3>, - <MT7623_PIN_121_MSDC0_DAT0_FUNC_NLD0>, - <MT7623_PIN_120_MSDC0_DAT1_FUNC_NLD1>, - <MT7623_PIN_113_MSDC0_DAT5_FUNC_NLD5>, - <MT7623_PIN_115_MSDC0_RSTB_FUNC_NLD8>, - <MT7623_PIN_119_MSDC0_DAT2_FUNC_NLD2>; - input-enable; - drive-strength = <MTK_DRIVE_8mA>; - bias-pull-up; - }; - - pins-we { - pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_NWEB>; - drive-strength = <MTK_DRIVE_8mA>; - bias-pull-up = <MTK_PUPD_SET_R1R0_10>; - }; - }; -}; diff --git a/arch/arm/boot/dts/mt7623n-rfb.dtsi b/arch/arm/boot/dts/mt7623n-rfb.dtsi index 256c5fd947bf..5c5cc7da5dd2 100644 --- a/arch/arm/boot/dts/mt7623n-rfb.dtsi +++ b/arch/arm/boot/dts/mt7623n-rfb.dtsi @@ -1,16 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2017 MediaTek Inc. * Author: John Crispin <john@phrozen.org> * Sean Wang <sean.wang@mediatek.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ /dts-v1/; @@ -47,10 +40,11 @@ }; memory@80000000 { + device_type = "memory"; reg = <0 0x80000000 0 0x40000000>; }; - usb_p1_vbus: regulator@0 { + usb_p1_vbus: regulator-5v { compatible = "regulator-fixed"; regulator-name = "usb_vbus"; regulator-min-microvolt = <5000000>; diff --git a/arch/arm/boot/dts/mt8127-moose.dts b/arch/arm/boot/dts/mt8127-moose.dts index 073e295a1cb4..308829b2da86 100644 --- a/arch/arm/boot/dts/mt8127-moose.dts +++ b/arch/arm/boot/dts/mt8127-moose.dts @@ -1,15 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2014 MediaTek Inc. * Author: Joe.C <yingjoe.chen@mediatek.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ /dts-v1/; diff --git a/arch/arm/boot/dts/mt8127.dtsi b/arch/arm/boot/dts/mt8127.dtsi index 916c095d11b9..3adfc6f7859c 100644 --- a/arch/arm/boot/dts/mt8127.dtsi +++ b/arch/arm/boot/dts/mt8127.dtsi @@ -1,15 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2014 MediaTek Inc. * Author: Joe.C <yingjoe.chen@mediatek.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ #include <dt-bindings/interrupt-controller/irq.h> diff --git a/arch/arm/boot/dts/mt8135-evbp1.dts b/arch/arm/boot/dts/mt8135-evbp1.dts index 460db6d05952..0ace7a40a60d 100644 --- a/arch/arm/boot/dts/mt8135-evbp1.dts +++ b/arch/arm/boot/dts/mt8135-evbp1.dts @@ -1,15 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2014 MediaTek Inc. * Author: Joe.C <yingjoe.chen@mediatek.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ /dts-v1/; diff --git a/arch/arm/boot/dts/mt8135.dtsi b/arch/arm/boot/dts/mt8135.dtsi index a97b4ee4ae79..688069dc1533 100644 --- a/arch/arm/boot/dts/mt8135.dtsi +++ b/arch/arm/boot/dts/mt8135.dtsi @@ -1,15 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2014 MediaTek Inc. * Author: Joe.C <yingjoe.chen@mediatek.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ #include <dt-bindings/clock/mt8135-clk.h> diff --git a/arch/arm/boot/dts/omap2420-n810.dts b/arch/arm/boot/dts/omap2420-n810.dts index 7c485fbfa535..96b9913ecc1f 100644 --- a/arch/arm/boot/dts/omap2420-n810.dts +++ b/arch/arm/boot/dts/omap2420-n810.dts @@ -6,11 +6,70 @@ / { model = "Nokia N810"; compatible = "nokia,n810", "nokia,n8x0", "ti,omap2420", "ti,omap2"; + + vio_ape: vio_ape { + compatible = "regulator-fixed"; + regulator-name = "vio_ape"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + v28_aic: v28_aic { + compatible = "regulator-fixed"; + regulator-name = "v28_aic"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; +}; + +&omap2420_pmx { + mcbsp2_pins: mcbsp2_pins { + pinctrl-single,pins = < + OMAP2420_CORE_IOPAD(0x0124, PIN_INPUT | MUX_MODE1) /* eac_ac_sclk.mcbsp2_clkx */ + OMAP2420_CORE_IOPAD(0x0125, PIN_INPUT | MUX_MODE1) /* eac_ac_fs.mcbsp2_fsx */ + OMAP2420_CORE_IOPAD(0x0126, PIN_INPUT | MUX_MODE1) /* eac_ac_din.mcbsp2_dr */ + OMAP2420_CORE_IOPAD(0x0127, PIN_OUTPUT | MUX_MODE1) /* eac_ac_dout.mcbsp2_dx */ + >; + }; + + aic33_pins: aic33_pins { + pinctrl-single,pins = < + OMAP2420_CORE_IOPAD(0x0129, PIN_OUTPUT | MUX_MODE3) /* eac_ac_rst.gpio118 */ + OMAP2420_CORE_IOPAD(0x00e8, PIN_OUTPUT | MUX_MODE2) /* vlynq_tx1.sys_clkout2 */ + >; + }; }; &i2c2 { - aic3x@18 { - compatible = "tlv320aic3x"; + aic33@18 { + compatible = "ti,tlv320aic33"; reg = <0x18>; + + pinctrl-names = "default"; + pinctrl-0 = <&aic33_pins>; + + gpio-reset = <&gpio4 22 GPIO_ACTIVE_LOW>; /* gpio118 */ + + ai3x-gpio-func = < + 10 /* AIC3X_GPIO1_FUNC_DIGITAL_MIC_MODCLK */ + 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */ + >; + ai3x-micbias-vg = <1>; /* 2V */ + + AVDD-supply = <&v28_aic>; + DRVDD-supply = <&v28_aic>; + IOVDD-supply = <&vio_ape>; + DVDD-supply = <&vio_ape>; + + assigned-clocks = <&sys_clkout2_src>, <&sys_clkout2>; + assigned-clock-parents = <&func_96m_ck>; + assigned-clock-rates = <0>, <12000000>; }; }; + +&mcbsp2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp2_pins>; + + status = "okay"; +}; diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 0349fcc9dc26..d80587de0bbf 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -30,6 +30,13 @@ ethernet = ðernet; }; + /* fixed 26MHz oscillator */ + hfclk_26m: oscillator { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <26000000>; + }; + leds { compatible = "gpio-leds"; @@ -274,6 +281,9 @@ interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; + clocks = <&hfclk_26m>; + clock-names = "fck"; + twl_audio: audio { compatible = "ti,twl4030-audio"; codec { diff --git a/arch/arm/boot/dts/omap3-cm-t3x.dtsi b/arch/arm/boot/dts/omap3-cm-t3x.dtsi index 9dcb18d22cde..cdb632df152a 100644 --- a/arch/arm/boot/dts/omap3-cm-t3x.dtsi +++ b/arch/arm/boot/dts/omap3-cm-t3x.dtsi @@ -60,7 +60,7 @@ regulator-max-microvolt = <3300000>; }; - tv0: connector { + tv0: svideo-connector { compatible = "svideo-connector"; label = "tv"; diff --git a/arch/arm/boot/dts/omap3-devkit8000-common.dtsi b/arch/arm/boot/dts/omap3-devkit8000-common.dtsi index 0c0bb1b01b0b..746a658e84b6 100644 --- a/arch/arm/boot/dts/omap3-devkit8000-common.dtsi +++ b/arch/arm/boot/dts/omap3-devkit8000-common.dtsi @@ -349,10 +349,17 @@ vdda_dac-supply = <&vdac>; port { - dpi_dvi_out: endpoint { + #address-cells = <1>; + #size-cells = <0>; + dpi_dvi_out: endpoint@0 { + reg = <0>; remote-endpoint = <&tfp410_in>; data-lines = <24>; }; + + endpoint@1 { + reg = <1>; + }; }; }; diff --git a/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi b/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi index 2d64bcffaaa8..1093387259e2 100644 --- a/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi +++ b/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi @@ -30,7 +30,10 @@ &dss { port { - dpi_lcd_out: endpoint { + #address-cells = <1>; + #size-cells = <0>; + dpi_lcd_out: endpoint@1 { + reg = <1>; remote-endpoint = <&lcd_in>; data-lines = <24>; }; diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi index 4170be70460e..ac830b917776 100644 --- a/arch/arm/boot/dts/omap3-gta04.dtsi +++ b/arch/arm/boot/dts/omap3-gta04.dtsi @@ -30,6 +30,13 @@ display0 = &lcd; }; + /* fixed 26MHz oscillator */ + hfclk_26m: oscillator { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <26000000>; + }; + gpio-keys { compatible = "gpio-keys"; @@ -312,6 +319,9 @@ interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; + clocks = <&hfclk_26m>; + clock-names = "fck"; + twl_audio: audio { compatible = "ti,twl4030-audio"; ti,enable-vibra = <1>; diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi index f83b1029b3b7..90c98f95b2b3 100644 --- a/arch/arm/boot/dts/omap3-pandora-common.dtsi +++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi @@ -27,6 +27,13 @@ display0 = &lcd; }; + /* fixed 26MHz oscillator */ + hfclk_26m: oscillator { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <26000000>; + }; + tv: connector { compatible = "connector-analog-tv"; label = "tv"; @@ -357,6 +364,9 @@ interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; + clocks = <&hfclk_26m>; + clock-names = "fck"; + twl_power: power { compatible = "ti,twl4030-power-reset"; ti,use_poweroff; @@ -611,7 +621,7 @@ pinctrl-names = "default"; pinctrl-0 = <&penirq_pins>; interrupt-parent = <&gpio3>; - interrupts = <30 0>; /* GPIO_94 */ + interrupts = <30 IRQ_TYPE_NONE>; /* GPIO_94 */ pendown-gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; vcc-supply = <&vaux4>; diff --git a/arch/arm/boot/dts/omap3-sb-t35.dtsi b/arch/arm/boot/dts/omap3-sb-t35.dtsi index 22b4c8bdcc65..fb9842fa922c 100644 --- a/arch/arm/boot/dts/omap3-sb-t35.dtsi +++ b/arch/arm/boot/dts/omap3-sb-t35.dtsi @@ -34,7 +34,7 @@ }; }; - dvi0: connector { + dvi0: dvi-connector { compatible = "dvi-connector"; label = "dvi"; diff --git a/arch/arm/boot/dts/pxa3xx.dtsi b/arch/arm/boot/dts/pxa3xx.dtsi index 982d1a62661d..132a3b8ab148 100644 --- a/arch/arm/boot/dts/pxa3xx.dtsi +++ b/arch/arm/boot/dts/pxa3xx.dtsi @@ -8,6 +8,10 @@ (gpio <= 98) ? (0x0400 + 4 * (gpio - 27)) : \ (gpio <= 127) ? (0x0600 + 4 * (gpio - 99)) : \ 0) +#define MFP_PIN_PXA300_2(gpio) \ + ((gpio <= 1) ? (0x674 + 4 * gpio) : \ + (gpio <= 6) ? (0x2dc + 4 * gpio) : \ + 0) #define MFP_PIN_PXA310(gpio) \ ((gpio <= 2) ? (0x00b4 + 4 * gpio) : \ @@ -18,6 +22,11 @@ (gpio <= 262) ? 0 : \ (gpio <= 268) ? (0x052c + 4 * (gpio - 263)) : \ 0) +#define MFP_PIN_PXA310_2(gpio) \ + ((gpio <= 1) ? (0x674 + 4 * gpio) : \ + (gpio <= 6) ? (0x2dc + 4 * gpio) : \ + (gpio <= 10) ? (0x52c + 4 * gpio) : \ + 0) #define MFP_PIN_PXA320(gpio) \ ((gpio <= 4) ? (0x0124 + 4 * gpio) : \ @@ -30,6 +39,10 @@ (gpio <= 98) ? (0x04f0 + 4 * (gpio - 74)) : \ (gpio <= 127) ? (0x0600 + 4 * (gpio - 99)) : \ 0) +#define MFP_PIN_PXA320_2(gpio) \ + ((gpio <= 3) ? (0x674 + 4 * gpio) : \ + (gpio <= 5) ? (0x284 + 4 * gpio) : \ + 0) /* * MFP Alternate functions for pins having a gpio. @@ -148,6 +161,7 @@ compatible = "intel,pxa3xx-gpio"; reg = <0x40e00000 0x10000>; clocks = <&clks CLK_GPIO>; + gpio-ranges = <&pinctrl 0 0 128>; interrupt-names = "gpio0", "gpio1", "gpio_mux"; interrupts = <8 9 10>; gpio-controller; @@ -160,7 +174,7 @@ compatible = "marvell,pxa-mmc"; reg = <0x41100000 0x1000>; interrupts = <23>; - clocks = <&clks CLK_MMC>; + clocks = <&clks CLK_MMC1>; dmas = <&pdma 21 3 &pdma 22 3>; dma-names = "rx", "tx"; @@ -171,7 +185,7 @@ compatible = "marvell,pxa-mmc"; reg = <0x42000000 0x1000>; interrupts = <41>; - clocks = <&clks CLK_MMC1>; + clocks = <&clks CLK_MMC2>; dmas = <&pdma 93 3 &pdma 94 3>; dma-names = "rx", "tx"; @@ -182,7 +196,7 @@ compatible = "marvell,pxa-mmc"; reg = <0x42500000 0x1000>; interrupts = <55>; - clocks = <&clks CLK_MMC2>; + clocks = <&clks CLK_MMC3>; dmas = <&pdma 46 3 &pdma 47 3>; dma-names = "rx", "tx"; diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index 5341a39c0392..4a99c9255104 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -444,7 +444,7 @@ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x12450000 0x100>, <0x12400000 0x03>; - interrupts = <0 193 0x0>; + interrupts = <0 193 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>; clock-names = "core", "iface"; status = "disabled"; @@ -456,11 +456,12 @@ pinctrl-1 = <&i2c1_pins_sleep>; pinctrl-names = "default", "sleep"; reg = <0x12460000 0x1000>; - interrupts = <0 194 IRQ_TYPE_NONE>; + interrupts = <0 194 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; clock-names = "core", "iface"; #address-cells = <1>; #size-cells = <0>; + status = "disabled"; }; }; @@ -484,11 +485,12 @@ pinctrl-0 = <&i2c2_pins>; pinctrl-1 = <&i2c2_pins_sleep>; pinctrl-names = "default", "sleep"; - interrupts = <0 196 IRQ_TYPE_NONE>; + interrupts = <0 196 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; clock-names = "core", "iface"; #address-cells = <1>; #size-cells = <0>; + status = "disabled"; }; }; @@ -508,12 +510,13 @@ pinctrl-1 = <&i2c3_pins_sleep>; pinctrl-names = "default", "sleep"; reg = <0x16280000 0x1000>; - interrupts = <GIC_SPI 151 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI3_QUP_CLK>, <&gcc GSBI3_H_CLK>; clock-names = "core", "iface"; #address-cells = <1>; #size-cells = <0>; + status = "disabled"; }; }; @@ -534,10 +537,11 @@ pinctrl-1 = <&i2c4_pins_sleep>; pinctrl-names = "default", "sleep"; reg = <0x16380000 0x1000>; - interrupts = <GIC_SPI 153 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; clock-names = "core", "iface"; + status = "disabled"; }; }; @@ -556,7 +560,7 @@ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x1a240000 0x100>, <0x1a200000 0x03>; - interrupts = <0 154 0x0>; + interrupts = <0 154 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; clock-names = "core", "iface"; status = "disabled"; @@ -565,7 +569,7 @@ gsbi5_spi: spi@1a280000 { compatible = "qcom,spi-qup-v1.1.1"; reg = <0x1a280000 0x1000>; - interrupts = <0 155 0>; + interrupts = <0 155 IRQ_TYPE_LEVEL_HIGH>; pinctrl-0 = <&spi5_default>; pinctrl-1 = <&spi5_sleep>; pinctrl-names = "default", "sleep"; @@ -592,7 +596,7 @@ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x16540000 0x100>, <0x16500000 0x03>; - interrupts = <0 156 0x0>; + interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>; clock-names = "core", "iface"; status = "disabled"; @@ -604,7 +608,7 @@ pinctrl-1 = <&i2c6_pins_sleep>; pinctrl-names = "default", "sleep"; reg = <0x16580000 0x1000>; - interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>; clock-names = "core", "iface"; @@ -628,7 +632,7 @@ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x16640000 0x1000>, <0x16600000 0x1000>; - interrupts = <0 158 0x0>; + interrupts = <0 158 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>; clock-names = "core", "iface"; status = "disabled"; @@ -640,7 +644,7 @@ pinctrl-1 = <&i2c7_pins_sleep>; pinctrl-names = "default", "sleep"; reg = <0x16680000 0x1000>; - interrupts = <GIC_SPI 159 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI7_QUP_CLK>, <&gcc GSBI7_H_CLK>; clock-names = "core", "iface"; @@ -1056,7 +1060,7 @@ compatible = "qcom,apq8064-ahci", "generic-ahci"; status = "disabled"; reg = <0x29000000 0x180>; - interrupts = <GIC_SPI 209 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc SFAB_SATA_S_H_CLK>, <&gcc SATA_H_CLK>, @@ -1082,7 +1086,7 @@ sdcc1bam:dma@12402000{ compatible = "qcom,bam-v1.3.0"; reg = <0x12402000 0x8000>; - interrupts = <0 98 0>; + interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc SDC1_H_CLK>; clock-names = "bam_clk"; #dma-cells = <1>; @@ -1092,7 +1096,7 @@ sdcc3bam:dma@12182000{ compatible = "qcom,bam-v1.3.0"; reg = <0x12182000 0x8000>; - interrupts = <0 96 0>; + interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc SDC3_H_CLK>; clock-names = "bam_clk"; #dma-cells = <1>; @@ -1102,7 +1106,7 @@ sdcc4bam:dma@121c2000{ compatible = "qcom,bam-v1.3.0"; reg = <0x121c2000 0x8000>; - interrupts = <0 95 0>; + interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc SDC4_H_CLK>; clock-names = "bam_clk"; #dma-cells = <1>; @@ -1181,7 +1185,7 @@ compatible = "qcom,adreno-3xx"; reg = <0x04300000 0x20000>; reg-names = "kgsl_3d0_reg_memory"; - interrupts = <GIC_SPI 80 0>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "kgsl_3d0_irq"; clock-names = "core_clk", @@ -1281,7 +1285,7 @@ label = "MDSS DSI CTRL->0"; #address-cells = <1>; #size-cells = <0>; - interrupts = <GIC_SPI 82 0>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; reg = <0x04700000 0x200>; reg-names = "dsi_ctrl"; @@ -1350,8 +1354,8 @@ <&mmcc MDP_AXI_CLK>; reg = <0x07500000 0x100000>; interrupts = - <GIC_SPI 63 0>, - <GIC_SPI 64 0>; + <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; qcom,ncb = <2>; }; @@ -1366,8 +1370,8 @@ <&mmcc MDP_AXI_CLK>; reg = <0x07600000 0x100000>; interrupts = - <GIC_SPI 61 0>, - <GIC_SPI 62 0>; + <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; qcom,ncb = <2>; }; @@ -1382,8 +1386,8 @@ <&mmcc GFX3D_AXI_CLK>; reg = <0x07c00000 0x100000>; interrupts = - <GIC_SPI 69 0>, - <GIC_SPI 70 0>; + <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; qcom,ncb = <3>; }; @@ -1398,8 +1402,8 @@ <&mmcc GFX3D_AXI_CLK>; reg = <0x07d00000 0x100000>; interrupts = - <GIC_SPI 210 0>, - <GIC_SPI 211 0>; + <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>; qcom,ncb = <3>; }; @@ -1417,8 +1421,8 @@ #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000 /* I/O */ - 0x82000000 0 0 0x08000000 0 0x07e00000>; /* memory */ - interrupts = <GIC_SPI 238 IRQ_TYPE_NONE>; + 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* memory */ + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "msi"; #interrupt-cells = <1>; interrupt-map-mask = <0 0 0 0x7>; diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi index e413b21ee331..418f9a022336 100644 --- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi @@ -20,6 +20,14 @@ model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK01.1"; compatible = "qcom,ipq4019"; + aliases { + serial0 = &blsp1_uart1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + soc { rng@22000 { status = "ok"; @@ -61,7 +69,7 @@ status = "ok"; }; - spi_0: spi@78b5000 { + spi@78b5000 { pinctrl-0 = <&spi_0_pins>; pinctrl-names = "default"; status = "ok"; diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts new file mode 100644 index 000000000000..7a96f300bc8d --- /dev/null +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2018, The Linux Foundation. All rights reserved. + +#include "qcom-ipq4019-ap.dk04.1.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK04.1-C1"; + compatible = "qcom,ipq4019-dk04.1-c1"; + + soc { + dma@7984000 { + status = "ok"; + }; + + qpic-nand@79b0000 { + status = "ok"; + }; + }; +}; diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c3.dts b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c3.dts new file mode 100644 index 000000000000..2d1c4c6e42f1 --- /dev/null +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c3.dts @@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2018, The Linux Foundation. All rights reserved. + +#include "qcom-ipq4019-ap.dk04.1.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK04.1-C3"; + compatible = "qcom,ipq4019-ap-dk04.1-c3"; +}; diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi new file mode 100644 index 000000000000..7c1eb1963c67 --- /dev/null +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi @@ -0,0 +1,111 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2018, The Linux Foundation. All rights reserved. + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK04.1"; + + aliases { + serial0 = &blsp1_uart1; + serial1 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256MB */ + }; + + soc { + pinctrl@1000000 { + serial_0_pins: serial0-pinmux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + + serial_1_pins: serial1-pinmux { + pins = "gpio8", "gpio9", + "gpio10", "gpio11"; + function = "blsp_uart1"; + bias-disable; + }; + + spi_0_pins: spi-0-pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + bias-disable; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + bias-disable; + output-high; + }; + }; + + i2c_0_pins: i2c-0-pinmux { + pins = "gpio20", "gpio21"; + function = "blsp_i2c0"; + bias-disable; + }; + + nand_pins: nand-pins { + pins = "gpio53", "gpio55", "gpio56", + "gpio57", "gpio58", "gpio59", + "gpio60", "gpio62", "gpio63", + "gpio64", "gpio65", "gpio66", + "gpio67", "gpio68", "gpio69"; + function = "qpic"; + }; + }; + + serial@78af000 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "ok"; + }; + + serial@78b0000 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "ok"; + }; + + dma@7884000 { + status = "ok"; + }; + + spi@78b5000 { /* BLSP1 QUP1 */ + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "ok"; + cs-gpios = <&tlmm 12 0>; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + compatible = "n25q128a11"; + spi-max-frequency = <24000000>; + }; + }; + + pci@40000000 { + status = "ok"; + perst-gpio = <&tlmm 38 0x1>; + }; + + qpic-nand@79b0000 { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + }; + }; +}; diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts new file mode 100644 index 000000000000..8c7ef6537ae6 --- /dev/null +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts @@ -0,0 +1,64 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2018, The Linux Foundation. All rights reserved. + +#include "qcom-ipq4019-ap.dk07.1.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK07.1-C1"; + compatible = "qcom,ipq4019-ap-dk07.1-c1"; + + soc { + pci@40000000 { + status = "ok"; + perst-gpio = <&tlmm 38 0x1>; + }; + + spi@78b6000 { + status = "ok"; + }; + + pinctrl@1000000 { + serial_1_pins: serial1-pinmux { + pins = "gpio8", "gpio9", + "gpio10", "gpio11"; + function = "blsp_uart1"; + bias-disable; + }; + + spi_0_pins: spi-0-pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + bias-disable; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + bias-disable; + output-high; + }; + }; + }; + + serial@78b0000 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "ok"; + }; + + spi@78b5000 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "ok"; + cs-gpios = <&tlmm 12 0>; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + compatible = "n25q128a11"; + spi-max-frequency = <24000000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts new file mode 100644 index 000000000000..af7a9028d492 --- /dev/null +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2018, The Linux Foundation. All rights reserved. + +#include "qcom-ipq4019-ap.dk07.1.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK07.1-C2"; + compatible = "qcom,ipq4019-ap-dk07.1-c2"; + + soc { + pinctrl@1000000 { + serial_1_pins: serial1-pinmux { + pins = "gpio8", "gpio9"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + serial@78b0000 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "ok"; + }; + }; +}; diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi new file mode 100644 index 000000000000..9f1a5a668772 --- /dev/null +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi @@ -0,0 +1,75 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2018, The Linux Foundation. All rights reserved. + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK07.1"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; /* 512MB */ + }; + + aliases { + serial0 = &blsp1_uart1; + serial1 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + soc { + pinctrl@1000000 { + serial_0_pins: serial0-pinmux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + + i2c_0_pins: i2c-0-pinmux { + pins = "gpio20", "gpio21"; + function = "blsp_i2c0"; + bias-disable; + }; + + nand_pins: nand-pins { + pins = "gpio53", "gpio55", "gpio56", + "gpio57", "gpio58", "gpio59", + "gpio60", "gpio62", "gpio63", + "gpio64", "gpio65", "gpio66", + "gpio67", "gpio68", "gpio69"; + function = "qpic"; + }; + }; + + serial@78af000 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "ok"; + }; + + dma@7884000 { + status = "ok"; + }; + + i2c@78b7000 { /* BLSP1 QUP2 */ + pinctrl-0 = <&i2c_0_pins>; + pinctrl-names = "default"; + status = "ok"; + }; + + dma@7984000 { + status = "ok"; + }; + + qpic-nand@79b0000 { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + status = "ok"; + }; + }; +}; diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi index 10d112a4078e..7bcd7635e723 100644 --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi @@ -23,9 +23,27 @@ compatible = "qcom,ipq4019"; interrupt-parent = <&intc>; + reserved-memory { + #address-cells = <0x1>; + #size-cells = <0x1>; + ranges; + + smem_region: smem@87e00000 { + reg = <0x87e00000 0x080000>; + no-map; + }; + + tz@87e80000 { + reg = <0x87e80000 0x180000>; + no-map; + }; + }; + aliases { - spi0 = &spi_0; - i2c0 = &i2c_0; + spi0 = &blsp1_spi1; + spi1 = &blsp1_spi2; + i2c0 = &blsp1_i2c3; + i2c1 = &blsp1_i2c4; }; cpus { @@ -45,7 +63,7 @@ 48000 1100000 200000 1100000 500000 1100000 - 666000 1100000 + 716000 1100000 >; clock-latency = <256000>; }; @@ -104,6 +122,12 @@ }; }; + firmware { + scm { + compatible = "qcom,scm-ipq4019"; + }; + }; + timer { compatible = "arm,armv7-timer"; interrupts = <1 2 0xf08>, @@ -149,13 +173,13 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; - interrupts = <0 208 0>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; }; blsp_dma: dma@7884000 { compatible = "qcom,bam-v1.7.0"; reg = <0x07884000 0x23000>; - interrupts = <GIC_SPI 238 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "bam_clk"; #dma-cells = <1>; @@ -163,7 +187,7 @@ status = "disabled"; }; - spi_0: spi@78b5000 { + blsp1_spi1: spi@78b5000 { /* BLSP1 QUP1 */ compatible = "qcom,spi-qup-v2.2.1"; reg = <0x78b5000 0x600>; interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; @@ -172,10 +196,26 @@ clock-names = "core", "iface"; #address-cells = <1>; #size-cells = <0>; + dmas = <&blsp_dma 5>, <&blsp_dma 4>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + blsp1_spi2: spi@78b6000 { /* BLSP1 QUP2 */ + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x78b6000 0x600>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&blsp_dma 7>, <&blsp_dma 6>; + dma-names = "rx", "tx"; status = "disabled"; }; - i2c_0: i2c@78b7000 { + blsp1_i2c3: i2c@78b7000 { /* BLSP1 QUP3 */ compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x78b7000 0x600>; interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; @@ -184,14 +224,29 @@ clock-names = "iface", "core"; #address-cells = <1>; #size-cells = <0>; + dmas = <&blsp_dma 9>, <&blsp_dma 8>; + dma-names = "rx", "tx"; status = "disabled"; }; + blsp1_i2c4: i2c@78b8000 { /* BLSP1 QUP4 */ + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x78b8000 0x600>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; + clock-names = "iface", "core"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&blsp_dma 11>, <&blsp_dma 10>; + dma-names = "rx", "tx"; + status = "disabled"; + }; cryptobam: dma@8e04000 { compatible = "qcom,bam-v1.7.0"; reg = <0x08e04000 0x20000>; - interrupts = <GIC_SPI 207 0>; + interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GCC_CRYPTO_AHB_CLK>; clock-names = "bam_clk"; #dma-cells = <1>; @@ -256,10 +311,10 @@ regulator; }; - serial@78af000 { + blsp1_uart1: serial@78af000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0x78af000 0x200>; - interrupts = <0 107 0>; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; @@ -268,10 +323,10 @@ dma-names = "rx", "tx"; }; - serial@78b0000 { + blsp1_uart2: serial@78b0000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0x78b0000 0x200>; - interrupts = <0 108 0>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; @@ -293,6 +348,101 @@ reg = <0x4ab000 0x4>; }; + pcie0: pci@40000000 { + compatible = "qcom,pcie-ipq4019", "snps,dw-pcie"; + reg = <0x40000000 0xf1d + 0x40000f20 0xa8 + 0x80000 0x2000 + 0x40100000 0x1000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x81000000 0 0x40200000 0x40200000 0 0x00100000 + 0x82000000 0 0x48000000 0x48000000 0 0x10000000>; + + interrupts = <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 144 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 145 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + clocks = <&gcc GCC_PCIE_AHB_CLK>, + <&gcc GCC_PCIE_AXI_M_CLK>, + <&gcc GCC_PCIE_AXI_S_CLK>; + clock-names = "aux", + "master_bus", + "slave_bus"; + + resets = <&gcc PCIE_AXI_M_ARES>, + <&gcc PCIE_AXI_S_ARES>, + <&gcc PCIE_PIPE_ARES>, + <&gcc PCIE_AXI_M_VMIDMT_ARES>, + <&gcc PCIE_AXI_S_XPU_ARES>, + <&gcc PCIE_PARF_XPU_ARES>, + <&gcc PCIE_PHY_ARES>, + <&gcc PCIE_AXI_M_STICKY_ARES>, + <&gcc PCIE_PIPE_STICKY_ARES>, + <&gcc PCIE_PWR_ARES>, + <&gcc PCIE_AHB_ARES>, + <&gcc PCIE_PHY_AHB_ARES>; + reset-names = "axi_m", + "axi_s", + "pipe", + "axi_m_vmid", + "axi_s_xpu", + "parf", + "phy", + "axi_m_sticky", + "pipe_sticky", + "pwr", + "ahb", + "phy_ahb"; + + status = "disabled"; + }; + + qpic_bam: dma@7984000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x7984000 0x1a000>; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_QPIC_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + status = "disabled"; + }; + + nand: qpic-nand@79b0000 { + compatible = "qcom,ipq4019-nand"; + reg = <0x79b0000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&gcc GCC_QPIC_CLK>, + <&gcc GCC_QPIC_AHB_CLK>; + clock-names = "core", "aon"; + + dmas = <&qpic_bam 0>, + <&qpic_bam 1>, + <&qpic_bam 2>; + dma-names = "tx", "rx", "cmd"; + status = "disabled"; + + nand@0 { + reg = <0>; + + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + }; + }; + wifi0: wifi@a000000 { compatible = "qcom,ipq4019-wifi"; reg = <0xa000000 0x200000>; @@ -326,7 +476,7 @@ <GIC_SPI 45 IRQ_TYPE_EDGE_RISING>, <GIC_SPI 46 IRQ_TYPE_EDGE_RISING>, <GIC_SPI 47 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 168 IRQ_TYPE_NONE>; + <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "msi0", "msi1", "msi2", "msi3", "msi4", "msi5", "msi6", "msi7", "msi8", "msi9", "msi10", "msi11", @@ -368,7 +518,7 @@ <GIC_SPI 61 IRQ_TYPE_EDGE_RISING>, <GIC_SPI 62 IRQ_TYPE_EDGE_RISING>, <GIC_SPI 63 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 169 IRQ_TYPE_NONE>; + <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "msi0", "msi1", "msi2", "msi3", "msi4", "msi5", "msi6", "msi7", "msi8", "msi9", "msi10", "msi11", diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi index 33030f9419fe..70698941f64c 100644 --- a/arch/arm/boot/dts/qcom-msm8660.dtsi +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi @@ -452,7 +452,7 @@ clock-names = "ram"; rpmcc: clock-controller { - compatible = "qcom,rpmcc-apq8660", "qcom,rpmcc"; + compatible = "qcom,rpmcc-msm8660", "qcom,rpmcc"; #clock-cells = <1>; }; diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts new file mode 100644 index 000000000000..5669f5f58a86 --- /dev/null +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts @@ -0,0 +1,436 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "qcom-msm8974.dtsi" +#include "qcom-pm8841.dtsi" +#include "qcom-pm8941.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> + +/ { + model = "Sony Xperia Z1 Compact"; + compatible = "sony,xperia-amami", "qcom,msm8974"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + input-name = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_pin_a>; + + volume-down { + label = "volume_down"; + gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = <KEY_VOLUMEDOWN>; + }; + + camera-snapshot { + label = "camera_snapshot"; + gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = <KEY_CAMERA>; + }; + + camera-focus { + label = "camera_focus"; + gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = <KEY_CAMERA_FOCUS>; + }; + + volume-up { + label = "volume_up"; + gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = <KEY_VOLUMEUP>; + }; + }; + + memory@0 { + reg = <0 0x40000000>, <0x40000000 0x40000000>; + device_type = "memory"; + }; + + smd { + rpm { + rpm_requests { + pm8841-regulators { + s1 { + regulator-min-microvolt = <675000>; + regulator-max-microvolt = <1050000>; + }; + + s2 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1050000>; + }; + + s3 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1050000>; + }; + + s4 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1050000>; + }; + }; + + pm8941-regulators { + vdd_l1_l3-supply = <&pm8941_s1>; + vdd_l2_lvs1_2_3-supply = <&pm8941_s3>; + vdd_l4_l11-supply = <&pm8941_s1>; + vdd_l5_l7-supply = <&pm8941_s2>; + vdd_l6_l12_l14_l15-supply = <&pm8941_s2>; + vdd_l9_l10_l17_l22-supply = <&vreg_boost>; + vdd_l13_l20_l23_l24-supply = <&vreg_boost>; + vdd_l21-supply = <&vreg_boost>; + + s1 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + s2 { + regulator-min-microvolt = <2150000>; + regulator-max-microvolt = <2150000>; + regulator-boot-on; + }; + + s3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + s4 { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + + regulator-always-on; + regulator-boot-on; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-boot-on; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-boot-on; + }; + + l8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l11 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1350000>; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + }; + + l13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + + regulator-boot-on; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l15 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l16 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + l17 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + l18 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l19 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l20 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + + regulator-allow-set-load; + regulator-boot-on; + regulator-system-load = <200000>; + }; + + l21 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + + regulator-boot-on; + }; + + l22 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + l23 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + l24 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + + regulator-boot-on; + }; + }; + }; + }; + }; +}; + +&soc { + sdhci@f9824900 { + status = "ok"; + + vmmc-supply = <&pm8941_l20>; + vqmmc-supply = <&pm8941_s3>; + + bus-width = <8>; + non-removable; + + pinctrl-names = "default"; + pinctrl-0 = <&sdhc1_pin_a>; + }; + + sdhci@f98a4900 { + status = "ok"; + + bus-width = <4>; + + vmmc-supply = <&pm8941_l21>; + vqmmc-supply = <&pm8941_l13>; + + cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>; + }; + + serial@f991e000 { + status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_uart2_pin_a>; + }; + + + pinctrl@fd510000 { + blsp1_uart2_pin_a: blsp1-uart2-pin-active { + rx { + pins = "gpio5"; + function = "blsp_uart2"; + + drive-strength = <2>; + bias-pull-up; + }; + + tx { + pins = "gpio4"; + function = "blsp_uart2"; + + drive-strength = <4>; + bias-disable; + }; + }; + + i2c2_pins: i2c2 { + mux { + pins = "gpio6", "gpio7"; + function = "blsp_i2c2"; + + drive-strength = <2>; + bias-disable; + }; + }; + + sdhc1_pin_a: sdhc1-pin-active { + clk { + pins = "sdc1_clk"; + drive-strength = <16>; + bias-disable; + }; + + cmd-data { + pins = "sdc1_cmd", "sdc1_data"; + drive-strength = <10>; + bias-pull-up; + }; + }; + + sdhc2_cd_pin_a: sdhc2-cd-pin-active { + pins = "gpio62"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + sdhc2_pin_a: sdhc2-pin-active { + clk { + pins = "sdc2_clk"; + drive-strength = <10>; + bias-disable; + }; + + cmd-data { + pins = "sdc2_cmd", "sdc2_data"; + drive-strength = <6>; + bias-pull-up; + }; + }; + }; + + dma-controller@f9944000 { + qcom,controlled-remotely; + }; + + usb@f9a55000 { + status = "ok"; + + phys = <&usb_hs1_phy>; + phy-select = <&tcsr 0xb000 0>; + extcon = <&smbb>, <&usb_id>; + vbus-supply = <&chg_otg>; + + hnp-disable; + srp-disable; + adp-disable; + + ulpi { + phy@a { + status = "ok"; + + v1p8-supply = <&pm8941_l6>; + v3p3-supply = <&pm8941_l24>; + + extcon = <&smbb>; + qcom,init-seq = /bits/ 8 <0x1 0x64>; + }; + }; + }; +}; + +&spmi_bus { + pm8941@0 { + charger@1000 { + qcom,fast-charge-safe-current = <1300000>; + qcom,fast-charge-current-limit = <1300000>; + qcom,dc-current-limit = <1300000>; + qcom,fast-charge-safe-voltage = <4400000>; + qcom,fast-charge-high-threshold-voltage = <4350000>; + qcom,fast-charge-low-threshold-voltage = <3400000>; + qcom,auto-recharge-threshold-voltage = <4200000>; + qcom,minimum-input-voltage = <4300000>; + }; + + gpios@c000 { + gpio_keys_pin_a: gpio-keys-active { + pins = "gpio2", "gpio3", "gpio4", "gpio5"; + function = "normal"; + + bias-pull-up; + power-source = <PM8941_GPIO_S3>; + }; + }; + + coincell@2800 { + status = "ok"; + qcom,rset-ohms = <2100>; + qcom,vset-millivolts = <3000>; + }; + }; + + pm8941@1 { + wled@d800 { + status = "ok"; + + qcom,cs-out; + qcom,current-limit = <20>; + qcom,current-boost-limit = <805>; + qcom,switching-freq = <1600>; + qcom,ovp = <29>; + qcom,num-strings = <2>; + }; + }; +}; diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi index 1d5ef55c7ee5..2515c5c217ac 100644 --- a/arch/arm/boot/dts/qcom-pm8941.dtsi +++ b/arch/arm/boot/dts/qcom-pm8941.dtsi @@ -139,6 +139,9 @@ #size-cells = <0>; #io-channel-cells = <1>; + bat_temp { + reg = <VADC_LR_MUX1_BAT_THERM>; + }; die_temp { reg = <VADC_DIE_TEMP>; }; @@ -154,6 +157,9 @@ ref_vdd { reg = <VADC_VDD_VADC>; }; + vbat_sns { + reg = <VADC_VBAT_SNS>; + }; }; pm8941_iadc: iadc@3600 { diff --git a/arch/arm/boot/dts/r7s72100.dtsi b/arch/arm/boot/dts/r7s72100.dtsi index ab9645a42eca..a54822e97bac 100644 --- a/arch/arm/boot/dts/r7s72100.dtsi +++ b/arch/arm/boot/dts/r7s72100.dtsi @@ -15,7 +15,6 @@ / { compatible = "renesas,r7s72100"; - interrupt-parent = <&gic>; #address-cells = <1>; #size-cells = <1>; @@ -31,61 +30,370 @@ spi4 = &spi4; }; - clocks { - ranges; + /* Fixed factor clocks */ + b_clk: b { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&cpg_clocks R7S72100_CLK_PLL>; + clock-mult = <1>; + clock-div = <3>; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <0>; + clock-frequency = <400000000>; + clocks = <&cpg_clocks R7S72100_CLK_I>; + next-level-cache = <&L2>; + }; + }; + + /* External clocks */ + extal_clk: extal { + #clock-cells = <0>; + compatible = "fixed-clock"; + /* If clk present, value must be set by board */ + clock-frequency = <0>; + }; + + p0_clk: p0 { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&cpg_clocks R7S72100_CLK_PLL>; + clock-mult = <1>; + clock-div = <12>; + }; + + p1_clk: p1 { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&cpg_clocks R7S72100_CLK_PLL>; + clock-mult = <1>; + clock-div = <6>; + }; + + pmu { + compatible = "arm,cortex-a9-pmu"; + interrupts-extended = <&gic GIC_PPI 0 IRQ_TYPE_LEVEL_HIGH>; + }; + + rtc_x1_clk: rtc_x1 { + #clock-cells = <0>; + compatible = "fixed-clock"; + /* If clk present, value must be set by board to 32678 */ + clock-frequency = <0>; + }; + + rtc_x3_clk: rtc_x3 { + #clock-cells = <0>; + compatible = "fixed-clock"; + /* If clk present, value must be set by board to 4000000 */ + clock-frequency = <0>; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&gic>; + #address-cells = <1>; #size-cells = <1>; + ranges; + + L2: cache-controller@3ffff000 { + compatible = "arm,pl310-cache"; + reg = <0x3ffff000 0x1000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + arm,early-bresp-disable; + arm,full-line-zero-disable; + cache-unified; + cache-level = <2>; + }; + + scif0: serial@e8007000 { + compatible = "renesas,scif-r7s72100", "renesas,scif"; + reg = <0xe8007000 64>; + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R7S72100_CLK_SCIF0>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scif1: serial@e8007800 { + compatible = "renesas,scif-r7s72100", "renesas,scif"; + reg = <0xe8007800 64>; + interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R7S72100_CLK_SCIF1>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scif2: serial@e8008000 { + compatible = "renesas,scif-r7s72100", "renesas,scif"; + reg = <0xe8008000 64>; + interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R7S72100_CLK_SCIF2>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scif3: serial@e8008800 { + compatible = "renesas,scif-r7s72100", "renesas,scif"; + reg = <0xe8008800 64>; + interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R7S72100_CLK_SCIF3>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; - /* External clocks */ - extal_clk: extal { - #clock-cells = <0>; - compatible = "fixed-clock"; - /* If clk present, value must be set by board */ - clock-frequency = <0>; + scif4: serial@e8009000 { + compatible = "renesas,scif-r7s72100", "renesas,scif"; + reg = <0xe8009000 64>; + interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R7S72100_CLK_SCIF4>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + status = "disabled"; }; - usb_x1_clk: usb_x1 { - #clock-cells = <0>; - compatible = "fixed-clock"; - /* If clk present, value must be set by board */ - clock-frequency = <0>; + scif5: serial@e8009800 { + compatible = "renesas,scif-r7s72100", "renesas,scif"; + reg = <0xe8009800 64>; + interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R7S72100_CLK_SCIF5>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + status = "disabled"; }; - rtc_x1_clk: rtc_x1 { - #clock-cells = <0>; - compatible = "fixed-clock"; - /* If clk present, value must be set by board to 32678 */ - clock-frequency = <0>; + scif6: serial@e800a000 { + compatible = "renesas,scif-r7s72100", "renesas,scif"; + reg = <0xe800a000 64>; + interrupts = <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R7S72100_CLK_SCIF6>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + status = "disabled"; }; - rtc_x3_clk: rtc_x3 { - #clock-cells = <0>; - compatible = "fixed-clock"; - /* If clk present, value must be set by board to 4000000 */ - clock-frequency = <0>; + scif7: serial@e800a800 { + compatible = "renesas,scif-r7s72100", "renesas,scif"; + reg = <0xe800a800 64>; + interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R7S72100_CLK_SCIF7>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + status = "disabled"; }; - /* Fixed factor clocks */ - b_clk: b { - #clock-cells = <0>; - compatible = "fixed-factor-clock"; - clocks = <&cpg_clocks R7S72100_CLK_PLL>; - clock-mult = <1>; - clock-div = <3>; + spi0: spi@e800c800 { + compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; + reg = <0xe800c800 0x24>; + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", "rx", "tx"; + clocks = <&mstp10_clks R7S72100_CLK_SPI0>; + power-domains = <&cpg_clocks>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; }; - p1_clk: p1 { - #clock-cells = <0>; - compatible = "fixed-factor-clock"; - clocks = <&cpg_clocks R7S72100_CLK_PLL>; - clock-mult = <1>; - clock-div = <6>; + + spi1: spi@e800d000 { + compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; + reg = <0xe800d000 0x24>; + interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", "rx", "tx"; + clocks = <&mstp10_clks R7S72100_CLK_SPI1>; + power-domains = <&cpg_clocks>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi2: spi@e800d800 { + compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; + reg = <0xe800d800 0x24>; + interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", "rx", "tx"; + clocks = <&mstp10_clks R7S72100_CLK_SPI2>; + power-domains = <&cpg_clocks>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; }; - p0_clk: p0 { - #clock-cells = <0>; - compatible = "fixed-factor-clock"; - clocks = <&cpg_clocks R7S72100_CLK_PLL>; - clock-mult = <1>; - clock-div = <12>; + + spi3: spi@e800e000 { + compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; + reg = <0xe800e000 0x24>; + interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", "rx", "tx"; + clocks = <&mstp10_clks R7S72100_CLK_SPI3>; + power-domains = <&cpg_clocks>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi4: spi@e800e800 { + compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; + reg = <0xe800e800 0x24>; + interrupts = <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", "rx", "tx"; + clocks = <&mstp10_clks R7S72100_CLK_SPI4>; + power-domains = <&cpg_clocks>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + usbhs0: usb@e8010000 { + compatible = "renesas,usbhs-r7s72100", "renesas,rza1-usbhs"; + reg = <0xe8010000 0x1a0>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R7S72100_CLK_USB0>; + renesas,buswait = <4>; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + usbhs1: usb@e8207000 { + compatible = "renesas,usbhs-r7s72100", "renesas,rza1-usbhs"; + reg = <0xe8207000 0x1a0>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R7S72100_CLK_USB1>; + renesas,buswait = <4>; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + mmcif: mmc@e804c800 { + compatible = "renesas,mmcif-r7s72100", "renesas,sh-mmcif"; + reg = <0xe804c800 0x80>; + interrupts = <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R7S72100_CLK_MMCIF>; + power-domains = <&cpg_clocks>; + reg-io-width = <4>; + bus-width = <8>; + status = "disabled"; + }; + + sdhi0: sd@e804e000 { + compatible = "renesas,sdhi-r7s72100"; + reg = <0xe804e000 0x100>; + interrupts = <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&mstp12_clks R7S72100_CLK_SDHI00>, + <&mstp12_clks R7S72100_CLK_SDHI01>; + clock-names = "core", "cd"; + power-domains = <&cpg_clocks>; + cap-sd-highspeed; + cap-sdio-irq; + status = "disabled"; + }; + + sdhi1: sd@e804e800 { + compatible = "renesas,sdhi-r7s72100"; + reg = <0xe804e800 0x100>; + interrupts = <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&mstp12_clks R7S72100_CLK_SDHI10>, + <&mstp12_clks R7S72100_CLK_SDHI11>; + clock-names = "core", "cd"; + power-domains = <&cpg_clocks>; + cap-sd-highspeed; + cap-sdio-irq; + status = "disabled"; + }; + + gic: interrupt-controller@e8201000 { + compatible = "arm,pl390"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0xe8201000 0x1000>, + <0xe8202000 0x1000>; + }; + + ether: ethernet@e8203000 { + compatible = "renesas,ether-r7s72100"; + reg = <0xe8203000 0x800>, + <0xe8204800 0x200>; + interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R7S72100_CLK_ETHER>; + power-domains = <&cpg_clocks>; + phy-mode = "mii"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + ceu: camera@e8210000 { + reg = <0xe8210000 0x3000>; + compatible = "renesas,r7s72100-ceu"; + interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp6_clks R7S72100_CLK_CEU>; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + wdt: watchdog@fcfe0000 { + compatible = "renesas,r7s72100-wdt", "renesas,rza-wdt"; + reg = <0xfcfe0000 0x6>; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&p0_clk>; }; /* Special CPG clocks */ @@ -135,9 +443,9 @@ #clock-cells = <1>; compatible = "renesas,r7s72100-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0xfcfe042c 4>; - clocks = <&p0_clk>; - clock-indices = <R7S72100_CLK_RTC>; - clock-output-names = "rtc"; + clocks = <&b_clk>, <&p0_clk>; + clock-indices = <R7S72100_CLK_CEU R7S72100_CLK_RTC>; + clock-output-names = "ceu", "rtc"; }; mstp7_clks: mstp7_clks@fcfe0430 { @@ -192,479 +500,209 @@ >; clock-output-names = "sdhi00", "sdhi01", "sdhi10", "sdhi11"; }; - }; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a9"; - reg = <0>; - clock-frequency = <400000000>; - clocks = <&cpg_clocks R7S72100_CLK_I>; - next-level-cache = <&L2>; - }; - }; - - pinctrl: pin-controller@fcfe3000 { - compatible = "renesas,r7s72100-ports"; - - reg = <0xfcfe3000 0x4230>; - - port0: gpio-0 { - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pinctrl 0 0 6>; - }; - - port1: gpio-1 { - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pinctrl 0 16 16>; - }; - port2: gpio-2 { - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pinctrl 0 32 16>; + pinctrl: pin-controller@fcfe3000 { + compatible = "renesas,r7s72100-ports"; + + reg = <0xfcfe3000 0x4230>; + + port0: gpio-0 { + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 0 6>; + }; + + port1: gpio-1 { + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 16 16>; + }; + + port2: gpio-2 { + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 32 16>; + }; + + port3: gpio-3 { + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 48 16>; + }; + + port4: gpio-4 { + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 64 16>; + }; + + port5: gpio-5 { + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 80 11>; + }; + + port6: gpio-6 { + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 96 16>; + }; + + port7: gpio-7 { + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 112 16>; + }; + + port8: gpio-8 { + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 128 16>; + }; + + port9: gpio-9 { + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 144 8>; + }; + + port10: gpio-10 { + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 160 16>; + }; + + port11: gpio-11 { + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 176 16>; + }; }; - port3: gpio-3 { - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pinctrl 0 48 16>; + ostm0: timer@fcfec000 { + compatible = "renesas,r7s72100-ostm", "renesas,ostm"; + reg = <0xfcfec000 0x30>; + interrupts = <GIC_SPI 102 IRQ_TYPE_EDGE_RISING>; + clocks = <&mstp5_clks R7S72100_CLK_OSTM0>; + power-domains = <&cpg_clocks>; + status = "disabled"; }; - port4: gpio-4 { - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pinctrl 0 64 16>; + ostm1: timer@fcfec400 { + compatible = "renesas,r7s72100-ostm", "renesas,ostm"; + reg = <0xfcfec400 0x30>; + interrupts = <GIC_SPI 103 IRQ_TYPE_EDGE_RISING>; + clocks = <&mstp5_clks R7S72100_CLK_OSTM1>; + power-domains = <&cpg_clocks>; + status = "disabled"; }; - port5: gpio-5 { - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pinctrl 0 80 11>; + i2c0: i2c@fcfee000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; + reg = <0xfcfee000 0x44>; + interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 159 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R7S72100_CLK_I2C0>; + clock-frequency = <100000>; + power-domains = <&cpg_clocks>; + status = "disabled"; }; - port6: gpio-6 { - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pinctrl 0 96 16>; + i2c1: i2c@fcfee400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; + reg = <0xfcfee400 0x44>; + interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 166 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 167 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R7S72100_CLK_I2C1>; + clock-frequency = <100000>; + power-domains = <&cpg_clocks>; + status = "disabled"; }; - port7: gpio-7 { - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pinctrl 0 112 16>; + i2c2: i2c@fcfee800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; + reg = <0xfcfee800 0x44>; + interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 174 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 175 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R7S72100_CLK_I2C2>; + clock-frequency = <100000>; + power-domains = <&cpg_clocks>; + status = "disabled"; }; - port8: gpio-8 { - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pinctrl 0 128 16>; + i2c3: i2c@fcfeec00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; + reg = <0xfcfeec00 0x44>; + interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 182 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 183 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R7S72100_CLK_I2C3>; + clock-frequency = <100000>; + power-domains = <&cpg_clocks>; + status = "disabled"; }; - port9: gpio-9 { - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pinctrl 0 144 8>; + mtu2: timer@fcff0000 { + compatible = "renesas,mtu2-r7s72100", "renesas,mtu2"; + reg = <0xfcff0000 0x400>; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tgi0a"; + clocks = <&mstp3_clks R7S72100_CLK_MTU2>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + status = "disabled"; }; - port10: gpio-10 { - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pinctrl 0 160 16>; + rtc: rtc@fcff1000 { + compatible = "renesas,r7s72100-rtc", "renesas,sh-rtc"; + reg = <0xfcff1000 0x2e>; + interrupts = <GIC_SPI 276 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "alarm", "period", "carry"; + clocks = <&mstp6_clks R7S72100_CLK_RTC>, <&rtc_x1_clk>, + <&rtc_x3_clk>, <&extal_clk>; + clock-names = "fck", "rtc_x1", "rtc_x3", "extal"; + power-domains = <&cpg_clocks>; + status = "disabled"; }; - - port11: gpio-11 { - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pinctrl 0 176 16>; - }; - }; - - scif0: serial@e8007000 { - compatible = "renesas,scif-r7s72100", "renesas,scif"; - reg = <0xe8007000 64>; - interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp4_clks R7S72100_CLK_SCIF0>; - clock-names = "fck"; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - scif1: serial@e8007800 { - compatible = "renesas,scif-r7s72100", "renesas,scif"; - reg = <0xe8007800 64>; - interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp4_clks R7S72100_CLK_SCIF1>; - clock-names = "fck"; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - scif2: serial@e8008000 { - compatible = "renesas,scif-r7s72100", "renesas,scif"; - reg = <0xe8008000 64>; - interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp4_clks R7S72100_CLK_SCIF2>; - clock-names = "fck"; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - scif3: serial@e8008800 { - compatible = "renesas,scif-r7s72100", "renesas,scif"; - reg = <0xe8008800 64>; - interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp4_clks R7S72100_CLK_SCIF3>; - clock-names = "fck"; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - scif4: serial@e8009000 { - compatible = "renesas,scif-r7s72100", "renesas,scif"; - reg = <0xe8009000 64>; - interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp4_clks R7S72100_CLK_SCIF4>; - clock-names = "fck"; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - scif5: serial@e8009800 { - compatible = "renesas,scif-r7s72100", "renesas,scif"; - reg = <0xe8009800 64>; - interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp4_clks R7S72100_CLK_SCIF5>; - clock-names = "fck"; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - scif6: serial@e800a000 { - compatible = "renesas,scif-r7s72100", "renesas,scif"; - reg = <0xe800a000 64>; - interrupts = <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp4_clks R7S72100_CLK_SCIF6>; - clock-names = "fck"; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - scif7: serial@e800a800 { - compatible = "renesas,scif-r7s72100", "renesas,scif"; - reg = <0xe800a800 64>; - interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp4_clks R7S72100_CLK_SCIF7>; - clock-names = "fck"; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - spi0: spi@e800c800 { - compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; - reg = <0xe800c800 0x24>; - interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "error", "rx", "tx"; - clocks = <&mstp10_clks R7S72100_CLK_SPI0>; - power-domains = <&cpg_clocks>; - num-cs = <1>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - spi1: spi@e800d000 { - compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; - reg = <0xe800d000 0x24>; - interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "error", "rx", "tx"; - clocks = <&mstp10_clks R7S72100_CLK_SPI1>; - power-domains = <&cpg_clocks>; - num-cs = <1>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - spi2: spi@e800d800 { - compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; - reg = <0xe800d800 0x24>; - interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "error", "rx", "tx"; - clocks = <&mstp10_clks R7S72100_CLK_SPI2>; - power-domains = <&cpg_clocks>; - num-cs = <1>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - spi3: spi@e800e000 { - compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; - reg = <0xe800e000 0x24>; - interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "error", "rx", "tx"; - clocks = <&mstp10_clks R7S72100_CLK_SPI3>; - power-domains = <&cpg_clocks>; - num-cs = <1>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - spi4: spi@e800e800 { - compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; - reg = <0xe800e800 0x24>; - interrupts = <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "error", "rx", "tx"; - clocks = <&mstp10_clks R7S72100_CLK_SPI4>; - power-domains = <&cpg_clocks>; - num-cs = <1>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - gic: interrupt-controller@e8201000 { - compatible = "arm,pl390"; - #interrupt-cells = <3>; - #address-cells = <0>; - interrupt-controller; - reg = <0xe8201000 0x1000>, - <0xe8202000 0x1000>; - }; - - L2: cache-controller@3ffff000 { - compatible = "arm,pl310-cache"; - reg = <0x3ffff000 0x1000>; - interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; - arm,early-bresp-disable; - arm,full-line-zero-disable; - cache-unified; - cache-level = <2>; - }; - - wdt: watchdog@fcfe0000 { - compatible = "renesas,r7s72100-wdt", "renesas,rza-wdt"; - reg = <0xfcfe0000 0x6>; - interrupts = <GIC_SPI 106 IRQ_TYPE_EDGE_RISING>; - clocks = <&p0_clk>; - }; - - i2c0: i2c@fcfee000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; - reg = <0xfcfee000 0x44>; - interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 159 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp9_clks R7S72100_CLK_I2C0>; - clock-frequency = <100000>; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - i2c1: i2c@fcfee400 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; - reg = <0xfcfee400 0x44>; - interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 166 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 167 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp9_clks R7S72100_CLK_I2C1>; - clock-frequency = <100000>; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - i2c2: i2c@fcfee800 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; - reg = <0xfcfee800 0x44>; - interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 174 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 175 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp9_clks R7S72100_CLK_I2C2>; - clock-frequency = <100000>; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - i2c3: i2c@fcfeec00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; - reg = <0xfcfeec00 0x44>; - interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 182 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 183 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp9_clks R7S72100_CLK_I2C3>; - clock-frequency = <100000>; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - mtu2: timer@fcff0000 { - compatible = "renesas,mtu2-r7s72100", "renesas,mtu2"; - reg = <0xfcff0000 0x400>; - interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tgi0a"; - clocks = <&mstp3_clks R7S72100_CLK_MTU2>; - clock-names = "fck"; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - ether: ethernet@e8203000 { - compatible = "renesas,ether-r7s72100"; - reg = <0xe8203000 0x800>, - <0xe8204800 0x200>; - interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp7_clks R7S72100_CLK_ETHER>; - power-domains = <&cpg_clocks>; - phy-mode = "mii"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - mmcif: mmc@e804c800 { - compatible = "renesas,mmcif-r7s72100", "renesas,sh-mmcif"; - reg = <0xe804c800 0x80>; - interrupts = <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH - GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH - GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp8_clks R7S72100_CLK_MMCIF>; - power-domains = <&cpg_clocks>; - reg-io-width = <4>; - bus-width = <8>; - status = "disabled"; - }; - - sdhi0: sd@e804e000 { - compatible = "renesas,sdhi-r7s72100"; - reg = <0xe804e000 0x100>; - interrupts = <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH - GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH - GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>; - - clocks = <&mstp12_clks R7S72100_CLK_SDHI00>, - <&mstp12_clks R7S72100_CLK_SDHI01>; - clock-names = "core", "cd"; - power-domains = <&cpg_clocks>; - cap-sd-highspeed; - cap-sdio-irq; - status = "disabled"; - }; - - sdhi1: sd@e804e800 { - compatible = "renesas,sdhi-r7s72100"; - reg = <0xe804e800 0x100>; - interrupts = <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH - GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH - GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>; - - clocks = <&mstp12_clks R7S72100_CLK_SDHI10>, - <&mstp12_clks R7S72100_CLK_SDHI11>; - clock-names = "core", "cd"; - power-domains = <&cpg_clocks>; - cap-sd-highspeed; - cap-sdio-irq; - status = "disabled"; - }; - - ostm0: timer@fcfec000 { - compatible = "renesas,r7s72100-ostm", "renesas,ostm"; - reg = <0xfcfec000 0x30>; - interrupts = <GIC_SPI 102 IRQ_TYPE_EDGE_RISING>; - clocks = <&mstp5_clks R7S72100_CLK_OSTM0>; - power-domains = <&cpg_clocks>; - status = "disabled"; - }; - - ostm1: timer@fcfec400 { - compatible = "renesas,r7s72100-ostm", "renesas,ostm"; - reg = <0xfcfec400 0x30>; - interrupts = <GIC_SPI 103 IRQ_TYPE_EDGE_RISING>; - clocks = <&mstp5_clks R7S72100_CLK_OSTM1>; - power-domains = <&cpg_clocks>; - status = "disabled"; }; - rtc: rtc@fcff1000 { - compatible = "renesas,r7s72100-rtc", "renesas,sh-rtc"; - reg = <0xfcff1000 0x2e>; - interrupts = <GIC_SPI 276 IRQ_TYPE_EDGE_RISING - GIC_SPI 277 IRQ_TYPE_EDGE_RISING - GIC_SPI 278 IRQ_TYPE_EDGE_RISING>; - interrupt-names = "alarm", "period", "carry"; - clocks = <&mstp6_clks R7S72100_CLK_RTC>, <&rtc_x1_clk>, - <&rtc_x3_clk>, <&extal_clk>; - clock-names = "fck", "rtc_x1", "rtc_x3", "extal"; - power-domains = <&cpg_clocks>; - status = "disabled"; + usb_x1_clk: usb_x1 { + #clock-cells = <0>; + compatible = "fixed-clock"; + /* If clk present, value must be set by board */ + clock-frequency = <0>; }; }; diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/r8a73a4-ape6evm.dts index ec7c86e06538..125c39c0222f 100644 --- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts +++ b/arch/arm/boot/dts/r8a73a4-ape6evm.dts @@ -234,7 +234,7 @@ &sdhi0 { vmmc-supply = <&vcc_sdhi0>; bus-width = <4>; - toshiba,mmc-wrprotect-disable; + disable-wp; pinctrl-names = "default"; pinctrl-0 = <&sdhi0_pins>; status = "okay"; @@ -244,7 +244,7 @@ vmmc-supply = <&ape6evm_fixed_3v3>; bus-width = <4>; broken-cd; - toshiba,mmc-wrprotect-disable; + disable-wp; pinctrl-names = "default"; pinctrl-0 = <&sdhi1_pins>; status = "okay"; diff --git a/arch/arm/boot/dts/r8a73a4.dtsi b/arch/arm/boot/dts/r8a73a4.dtsi index 8e48090e4fdc..080d037f5733 100644 --- a/arch/arm/boot/dts/r8a73a4.dtsi +++ b/arch/arm/boot/dts/r8a73a4.dtsi @@ -57,10 +57,10 @@ timer { compatible = "arm,armv7-timer"; - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; }; dbsc1: memory-controller@e6790000 { @@ -464,7 +464,7 @@ <0 0xf1002000 0 0x2000>, <0 0xf1004000 0 0x2000>, <0 0xf1006000 0 0x2000>; - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>; clocks = <&mstp4_clks R8A73A4_CLK_INTC_SYS>; clock-names = "clk"; power-domains = <&pd_c4>; diff --git a/arch/arm/boot/dts/r8a7740.dtsi b/arch/arm/boot/dts/r8a7740.dtsi index afd3bc5e6cf2..eb9a911deefb 100644 --- a/arch/arm/boot/dts/r8a7740.dtsi +++ b/arch/arm/boot/dts/r8a7740.dtsi @@ -67,6 +67,24 @@ power-domains = <&pd_d4>; }; + ceu0: ceu@fe910000 { + reg = <0xfe910000 0x3000>; + compatible = "renesas,r8a7740-ceu"; + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp1_clks R8A7740_CLK_CEU20>; + power-domains = <&pd_a4r>; + status = "disabled"; + }; + + ceu1: ceu@fe914000 { + reg = <0xfe914000 0x3000>; + compatible = "renesas,r8a7740-ceu"; + interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp1_clks R8A7740_CLK_CEU21>; + power-domains = <&pd_a4r>; + status = "disabled"; + }; + cmt1: timer@e6138000 { compatible = "renesas,cmt-48-r8a7740", "renesas,cmt-48"; reg = <0xe6138000 0x170>; diff --git a/arch/arm/boot/dts/r8a7743-iwg20m.dtsi b/arch/arm/boot/dts/r8a7743-iwg20m.dtsi index 1d3e9503c5bd..d364685d9184 100644 --- a/arch/arm/boot/dts/r8a7743-iwg20m.dtsi +++ b/arch/arm/boot/dts/r8a7743-iwg20m.dtsi @@ -91,6 +91,11 @@ }; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &sdhi0 { pinctrl-0 = <&sdhi0_pins>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/r8a7743.dtsi b/arch/arm/boot/dts/r8a7743.dtsi index 1d9073ba0ce0..142949d7066f 100644 --- a/arch/arm/boot/dts/r8a7743.dtsi +++ b/arch/arm/boot/dts/r8a7743.dtsi @@ -125,6 +125,13 @@ clock-frequency = <0>; }; + pmu { + compatible = "arm,cortex-a15-pmu"; + interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>; + }; + /* External SCIF clock */ scif_clk: scif { compatible = "fixed-clock"; @@ -297,6 +304,16 @@ reg = <0 0xe6160000 0 0x100>; }; + rwdt: watchdog@e6020000 { + compatible = "renesas,r8a7743-wdt", + "renesas,rcar-gen2-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 402>; + power-domains = <&sysc R8A7743_PD_ALWAYS_ON>; + resets = <&cpg 402>; + status = "disabled"; + }; + sysc: system-controller@e6180000 { compatible = "renesas,r8a7743-sysc"; reg = <0 0xe6180000 0 0x200>; @@ -407,7 +424,7 @@ smp-sram@0 { compatible = "renesas,smp-sram"; - reg = <0 0x10>; + reg = <0 0x100>; }; }; diff --git a/arch/arm/boot/dts/r8a7745-iwg22m.dtsi b/arch/arm/boot/dts/r8a7745-iwg22m.dtsi index 8d0a392b6811..29b6e10fdf96 100644 --- a/arch/arm/boot/dts/r8a7745-iwg22m.dtsi +++ b/arch/arm/boot/dts/r8a7745-iwg22m.dtsi @@ -91,6 +91,11 @@ }; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &sdhi1 { pinctrl-0 = <&sdhi1_pins>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/r8a7745.dtsi b/arch/arm/boot/dts/r8a7745.dtsi index dd49a8b48f3e..1cb7a7ab0418 100644 --- a/arch/arm/boot/dts/r8a7745.dtsi +++ b/arch/arm/boot/dts/r8a7745.dtsi @@ -105,6 +105,13 @@ clock-frequency = <0>; }; + pmu { + compatible = "arm,cortex-a7-pmu"; + interrupts-extended = <&gic GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>; + }; + /* External SCIF clock */ scif_clk: scif { compatible = "fixed-clock"; @@ -262,6 +269,16 @@ reg = <0 0xe6160000 0 0x100>; }; + rwdt: watchdog@e6020000 { + compatible = "renesas,r8a7745-wdt", + "renesas,rcar-gen2-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 402>; + power-domains = <&sysc R8A7745_PD_ALWAYS_ON>; + resets = <&cpg 402>; + status = "disabled"; + }; + sysc: system-controller@e6180000 { compatible = "renesas,r8a7745-sysc"; reg = <0 0xe6180000 0 0x200>; @@ -360,7 +377,7 @@ smp-sram@0 { compatible = "renesas,smp-sram"; - reg = <0 0x10>; + reg = <0 0x100>; }; }; diff --git a/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts b/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts new file mode 100644 index 000000000000..e3585daafdd6 --- /dev/null +++ b/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts @@ -0,0 +1,48 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for the iWave-RZ/G1C single board computer + * + * Copyright (C) 2018 Renesas Electronics Corp. + */ + +/dts-v1/; +#include "r8a77470.dtsi" +/ { + model = "iWave iW-RainboW-G23S single board computer based on RZ/G1C"; + compatible = "iwave,g23s", "renesas,r8a77470"; + + aliases { + ethernet0 = &avb; + serial1 = &scif1; + }; + + chosen { + bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp"; + stdout-path = "serial1:115200n8"; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0 0x40000000 0 0x20000000>; + }; +}; + +&avb { + phy-handle = <&phy3>; + phy-mode = "gmii"; + renesas,no-ether-link; + status = "okay"; + + phy3: ethernet-phy@3 { + reg = <3>; + micrel,led-mode = <1>; + }; +}; + +&extal_clk { + clock-frequency = <20000000>; +}; + +&scif1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/r8a77470.dtsi b/arch/arm/boot/dts/r8a77470.dtsi new file mode 100644 index 000000000000..c85032f9605b --- /dev/null +++ b/arch/arm/boot/dts/r8a77470.dtsi @@ -0,0 +1,336 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for the r8a77470 SoC + * + * Copyright (C) 2018 Renesas Electronics Corp. + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/renesas-cpg-mssr.h> +/ { + compatible = "renesas,r8a77470"; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0>; + clock-frequency = <1000000000>; + clocks = <&cpg CPG_CORE 0>; + power-domains = <&sysc 5>; + next-level-cache = <&L2_CA7>; + }; + + + L2_CA7: cache-controller-0 { + compatible = "cache"; + cache-unified; + cache-level = <2>; + power-domains = <&sysc 21>; + }; + }; + + /* External root clock */ + extal_clk: extal { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board. */ + clock-frequency = <0>; + }; + + /* External SCIF clock */ + scif_clk: scif { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board. */ + clock-frequency = <0>; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&gic>; + + #address-cells = <2>; + #size-cells = <2>; + ranges; + + cpg: clock-controller@e6150000 { + compatible = "renesas,r8a77470-cpg-mssr"; + reg = <0 0xe6150000 0 0x1000>; + clocks = <&extal_clk>, <&usb_extal_clk>; + clock-names = "extal", "usb_extal"; + #clock-cells = <2>; + #power-domain-cells = <0>; + #reset-cells = <1>; + }; + + rst: reset-controller@e6160000 { + compatible = "renesas,r8a77470-rst"; + reg = <0 0xe6160000 0 0x100>; + }; + + sysc: system-controller@e6180000 { + compatible = "renesas,r8a77470-sysc"; + reg = <0 0xe6180000 0 0x200>; + #power-domain-cells = <1>; + }; + + irqc: interrupt-controller@e61c0000 { + compatible = "renesas,irqc-r8a77470", "renesas,irqc"; + #interrupt-cells = <2>; + interrupt-controller; + reg = <0 0xe61c0000 0 0x200>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 407>; + power-domains = <&sysc 32>; + resets = <&cpg 407>; + }; + + icram0: sram@e63a0000 { + compatible = "mmio-sram"; + reg = <0 0xe63a0000 0 0x12000>; + }; + + icram1: sram@e63c0000 { + compatible = "mmio-sram"; + reg = <0 0xe63c0000 0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0xe63c0000 0x1000>; + + smp-sram@0 { + compatible = "renesas,smp-sram"; + reg = <0 0x100>; + }; + }; + + icram2: sram@e6300000 { + compatible = "mmio-sram"; + reg = <0 0xe6300000 0 0x20000>; + }; + + dmac0: dma-controller@e6700000 { + compatible = "renesas,dmac-r8a77470", + "renesas,rcar-dmac"; + reg = <0 0xe6700000 0 0x20000>; + interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14"; + clocks = <&cpg CPG_MOD 219>; + clock-names = "fck"; + power-domains = <&sysc 32>; + resets = <&cpg 219>; + #dma-cells = <1>; + dma-channels = <15>; + }; + + dmac1: dma-controller@e6720000 { + compatible = "renesas,dmac-r8a77470", + "renesas,rcar-dmac"; + reg = <0 0xe6720000 0 0x20000>; + interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14"; + clocks = <&cpg CPG_MOD 218>; + clock-names = "fck"; + power-domains = <&sysc 32>; + resets = <&cpg 218>; + #dma-cells = <1>; + dma-channels = <15>; + }; + + avb: ethernet@e6800000 { + compatible = "renesas,etheravb-r8a77470", + "renesas,etheravb-rcar-gen2"; + reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>; + interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 812>; + power-domains = <&sysc 32>; + resets = <&cpg 812>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + scif0: serial@e6e60000 { + compatible = "renesas,scif-r8a77470", + "renesas,rcar-gen2-scif", "renesas,scif"; + reg = <0 0xe6e60000 0 0x40>; + interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 721>, + <&cpg CPG_CORE 5>, <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x29>, <&dmac0 0x2a>, + <&dmac1 0x29>, <&dmac1 0x2a>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc 32>; + resets = <&cpg 721>; + status = "disabled"; + }; + + scif1: serial@e6e68000 { + compatible = "renesas,scif-r8a77470", + "renesas,rcar-gen2-scif", "renesas,scif"; + reg = <0 0xe6e68000 0 0x40>; + interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 720>, + <&cpg CPG_CORE 5>, <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x2d>, <&dmac0 0x2e>, + <&dmac1 0x2d>, <&dmac1 0x2e>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc 32>; + resets = <&cpg 720>; + status = "disabled"; + }; + + scif2: serial@e6e58000 { + compatible = "renesas,scif-r8a77470", + "renesas,rcar-gen2-scif", "renesas,scif"; + reg = <0 0xe6e58000 0 0x40>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 719>, + <&cpg CPG_CORE 5>, <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x2b>, <&dmac0 0x2c>, + <&dmac1 0x2b>, <&dmac1 0x2c>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc 32>; + resets = <&cpg 719>; + status = "disabled"; + }; + + scif3: serial@e6ea8000 { + compatible = "renesas,scif-r8a77470", + "renesas,rcar-gen2-scif", "renesas,scif"; + reg = <0 0xe6ea8000 0 0x40>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 718>, + <&cpg CPG_CORE 5>, <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x2f>, <&dmac0 0x30>, + <&dmac1 0x2f>, <&dmac1 0x30>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc 32>; + resets = <&cpg 718>; + status = "disabled"; + }; + + scif4: serial@e6ee0000 { + compatible = "renesas,scif-r8a77470", + "renesas,rcar-gen2-scif", "renesas,scif"; + reg = <0 0xe6ee0000 0 0x40>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 715>, + <&cpg CPG_CORE 5>, <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0xfb>, <&dmac0 0xfc>, + <&dmac1 0xfb>, <&dmac1 0xfc>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc 32>; + resets = <&cpg 715>; + status = "disabled"; + }; + + scif5: serial@e6ee8000 { + compatible = "renesas,scif-r8a77470", + "renesas,rcar-gen2-scif", "renesas,scif"; + reg = <0 0xe6ee8000 0 0x40>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 714>, + <&cpg CPG_CORE 5>, <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0xfd>, <&dmac0 0xfe>, + <&dmac1 0xfd>, <&dmac1 0xfe>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc 32>; + resets = <&cpg 714>; + status = "disabled"; + }; + + gic: interrupt-controller@f1001000 { + compatible = "arm,gic-400"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0 0xf1001000 0 0x1000>, <0 0xf1002000 0 0x2000>, + <0 0xf1004000 0 0x2000>, <0 0xf1006000 0 0x2000>; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; + clocks = <&cpg CPG_MOD 408>; + clock-names = "clk"; + power-domains = <&sysc 32>; + resets = <&cpg 408>; + }; + + prr: chipid@ff000044 { + compatible = "renesas,prr"; + reg = <0 0xff000044 0 4>; + }; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, + <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, + <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, + <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>; + }; + + /* External USB clock - can be overridden by the board */ + usb_extal_clk: usb_extal { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + }; +}; diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts index 063fdb65dc60..092610e3f953 100644 --- a/arch/arm/boot/dts/r8a7790-lager.dts +++ b/arch/arm/boot/dts/r8a7790-lager.dts @@ -379,7 +379,7 @@ port@0 { reg = <0>; adv7511_in: endpoint { - remote-endpoint = <&du_out_lvds0>; + remote-endpoint = <&lvds0_out>; }; }; @@ -467,10 +467,8 @@ status = "okay"; clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>, - <&cpg CPG_MOD 726>, <&cpg CPG_MOD 725>, <&x13_clk>, <&x2_clk>; - clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1", - "dclkin.0", "dclkin.1"; + clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1"; ports { port@0 { @@ -478,12 +476,26 @@ remote-endpoint = <&adv7123_in>; }; }; + }; +}; + +&lvds0 { + status = "okay"; + + ports { port@1 { endpoint { remote-endpoint = <&adv7511_in>; }; }; - port@2 { + }; +}; + +&lvds1 { + status = "okay"; + + ports { + port@1 { lvds_connector: endpoint { }; }; @@ -890,9 +902,6 @@ status = "okay"; port { - #address-cells = <1>; - #size-cells = <0>; - vin1ep0: endpoint { remote-endpoint = <&adv7180>; bus-width = <8>; @@ -917,6 +926,11 @@ }; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &ssi1 { shared-pin; }; diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index e4367cecad18..4d06b154bd7e 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -202,6 +202,24 @@ clock-frequency = <0>; }; + pmu-0 { + compatible = "arm,cortex-a15-pmu"; + interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; + }; + + pmu-1 { + compatible = "arm,cortex-a7-pmu"; + interrupts-extended = <&gic GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>; + }; + /* External SCIF clock */ scif_clk: scif { compatible = "fixed-clock"; @@ -218,6 +236,16 @@ #size-cells = <2>; ranges; + rwdt: watchdog@e6020000 { + compatible = "renesas,r8a7790-wdt", + "renesas,rcar-gen2-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 402>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 402>; + status = "disabled"; + }; + gpio0: gpio@e6050000 { compatible = "renesas,gpio-r8a7790", "renesas,rcar-gen2-gpio"; @@ -443,7 +471,7 @@ smp-sram@0 { compatible = "renesas,smp-sram"; - reg = <0 0x10>; + reg = <0 0x100>; }; }; @@ -1544,7 +1572,7 @@ interrupt-controller; reg = <0 0xf1001000 0 0x1000>, <0 0xf1002000 0 0x2000>, <0 0xf1004000 0 0x2000>, <0 0xf1006000 0 0x2000>; - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>; clocks = <&cpg CPG_MOD 408>; clock-names = "clk"; power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; @@ -1615,6 +1643,33 @@ resets = <&cpg 127>; }; + fdp1@fe940000 { + compatible = "renesas,fdp1"; + reg = <0 0xfe940000 0 0x2400>; + interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 119>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 119>; + }; + + fdp1@fe944000 { + compatible = "renesas,fdp1"; + reg = <0 0xfe944000 0 0x2400>; + interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 118>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 118>; + }; + + fdp1@fe948000 { + compatible = "renesas,fdp1"; + reg = <0 0xfe948000 0 0x2400>; + interrupts = <GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 117>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 117>; + }; + jpu: jpeg-codec@fe980000 { compatible = "renesas,jpu-r8a7790", "renesas,rcar-gen2-jpu"; @@ -1627,18 +1682,13 @@ du: display@feb00000 { compatible = "renesas,du-r8a7790"; - reg = <0 0xfeb00000 0 0x70000>, - <0 0xfeb90000 0 0x1c>, - <0 0xfeb94000 0 0x1c>; - reg-names = "du", "lvds.0", "lvds.1"; + reg = <0 0xfeb00000 0 0x70000>; interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, - <&cpg CPG_MOD 722>, <&cpg CPG_MOD 726>, - <&cpg CPG_MOD 725>; - clock-names = "du.0", "du.1", "du.2", "lvds.0", - "lvds.1"; + <&cpg CPG_MOD 722>; + clock-names = "du.0", "du.1", "du.2"; status = "disabled"; ports { @@ -1653,11 +1703,65 @@ port@1 { reg = <1>; du_out_lvds0: endpoint { + remote-endpoint = <&lvds0_in>; }; }; port@2 { reg = <2>; du_out_lvds1: endpoint { + remote-endpoint = <&lvds1_in>; + }; + }; + }; + }; + + lvds0: lvds@feb90000 { + compatible = "renesas,r8a7790-lvds"; + reg = <0 0xfeb90000 0 0x1c>; + clocks = <&cpg CPG_MOD 726>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 726>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + lvds0_in: endpoint { + remote-endpoint = <&du_out_lvds0>; + }; + }; + port@1 { + reg = <1>; + lvds0_out: endpoint { + }; + }; + }; + }; + + lvds1: lvds@feb94000 { + compatible = "renesas,r8a7790-lvds"; + reg = <0 0xfeb94000 0 0x1c>; + clocks = <&cpg CPG_MOD 725>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 725>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + lvds1_in: endpoint { + remote-endpoint = <&du_out_lvds1>; + }; + }; + port@1 { + reg = <1>; + lvds1_out: endpoint { }; }; }; @@ -1724,10 +1828,10 @@ timer { compatible = "arm,armv7-timer"; - interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; }; /* External USB clock - can be overridden by the board */ diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index f40321a1c917..8ab793d8b2fd 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -468,10 +468,9 @@ pinctrl-names = "default"; status = "okay"; - clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 726>, + clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&x13_clk>, <&x2_clk>; - clock-names = "du.0", "du.1", "lvds.0", - "dclkin.0", "dclkin.1"; + clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1"; ports { port@0 { @@ -479,6 +478,13 @@ remote-endpoint = <&adv7511_in>; }; }; + }; +}; + +&lvds0 { + status = "okay"; + + ports { port@1 { lvds_connector: endpoint { }; @@ -637,6 +643,11 @@ status = "okay"; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &sata0 { status = "okay"; }; @@ -844,9 +855,6 @@ pinctrl-names = "default"; port { - #address-cells = <1>; - #size-cells = <0>; - vin0ep2: endpoint { remote-endpoint = <&adv7612_out>; bus-width = <24>; @@ -865,9 +873,6 @@ pinctrl-names = "default"; port { - #address-cells = <1>; - #size-cells = <0>; - vin1ep: endpoint { remote-endpoint = <&adv7180>; bus-width = <8>; diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts index c14e6fe9e4f6..a01101b49d99 100644 --- a/arch/arm/boot/dts/r8a7791-porter.dts +++ b/arch/arm/boot/dts/r8a7791-porter.dts @@ -386,9 +386,6 @@ pinctrl-names = "default"; port { - #address-cells = <1>; - #size-cells = <0>; - vin0ep: endpoint { remote-endpoint = <&adv7180>; bus-width = <8>; @@ -441,10 +438,9 @@ pinctrl-names = "default"; status = "okay"; - clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 726>, + clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&x3_clk>, <&x16_clk>; - clock-names = "du.0", "du.1", "lvds.0", - "dclkin.0", "dclkin.1"; + clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1"; ports { port@0 { @@ -455,6 +451,17 @@ }; }; +&lvds0 { + status = "okay"; + + ports { + port@1 { + lvds_connector: endpoint { + }; + }; + }; +}; + &rcar_sound { pinctrl-0 = <&ssi_pins &audio_clk_pins>; pinctrl-names = "default"; @@ -471,6 +478,11 @@ }; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &ssi1 { shared-pin; }; diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index f11dab71b03a..6e1dd7ad7bd6 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -126,6 +126,13 @@ clock-frequency = <0>; }; + pmu { + compatible = "arm,cortex-a15-pmu"; + interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>; + }; + /* External SCIF clock */ scif_clk: scif { compatible = "fixed-clock"; @@ -142,6 +149,16 @@ #size-cells = <2>; ranges; + rwdt: watchdog@e6020000 { + compatible = "renesas,r8a7791-wdt", + "renesas,rcar-gen2-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 402>; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + resets = <&cpg 402>; + status = "disabled"; + }; + gpio0: gpio@e6050000 { compatible = "renesas,gpio-r8a7791", "renesas,rcar-gen2-gpio"; @@ -407,7 +424,7 @@ smp-sram@0 { compatible = "renesas,smp-sram"; - reg = <0 0x10>; + reg = <0 0x100>; }; }; @@ -1621,6 +1638,24 @@ resets = <&cpg 127>; }; + fdp1@fe940000 { + compatible = "renesas,fdp1"; + reg = <0 0xfe940000 0 0x2400>; + interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 119>; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + resets = <&cpg 119>; + }; + + fdp1@fe944000 { + compatible = "renesas,fdp1"; + reg = <0 0xfe944000 0 0x2400>; + interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 118>; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + resets = <&cpg 118>; + }; + jpu: jpeg-codec@fe980000 { compatible = "renesas,jpu-r8a7791", "renesas,rcar-gen2-jpu"; @@ -1633,15 +1668,12 @@ du: display@feb00000 { compatible = "renesas,du-r8a7791"; - reg = <0 0xfeb00000 0 0x40000>, - <0 0xfeb90000 0 0x1c>; - reg-names = "du", "lvds.0"; + reg = <0 0xfeb00000 0 0x40000>; interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 724>, - <&cpg CPG_MOD 723>, - <&cpg CPG_MOD 726>; - clock-names = "du.0", "du.1", "lvds.0"; + <&cpg CPG_MOD 723>; + clock-names = "du.0", "du.1"; status = "disabled"; ports { @@ -1656,6 +1688,33 @@ port@1 { reg = <1>; du_out_lvds0: endpoint { + remote-endpoint = <&lvds0_in>; + }; + }; + }; + }; + + lvds0: lvds@feb90000 { + compatible = "renesas,r8a7791-lvds"; + reg = <0 0xfeb90000 0 0x1c>; + clocks = <&cpg CPG_MOD 726>; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + resets = <&cpg 726>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + lvds0_in: endpoint { + remote-endpoint = <&du_out_lvds0>; + }; + }; + port@1 { + reg = <1>; + lvds0_out: endpoint { }; }; }; diff --git a/arch/arm/boot/dts/r8a7792-blanche.dts b/arch/arm/boot/dts/r8a7792-blanche.dts index 9b67dca6c9ef..04fb70931b3b 100644 --- a/arch/arm/boot/dts/r8a7792-blanche.dts +++ b/arch/arm/boot/dts/r8a7792-blanche.dts @@ -239,6 +239,11 @@ }; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &scif0 { pinctrl-0 = <&scif0_pins>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/r8a7792-wheat.dts b/arch/arm/boot/dts/r8a7792-wheat.dts index b9471b67b728..db01de7a3811 100644 --- a/arch/arm/boot/dts/r8a7792-wheat.dts +++ b/arch/arm/boot/dts/r8a7792-wheat.dts @@ -168,6 +168,11 @@ }; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &scif0 { pinctrl-0 = <&scif0_pins>; pinctrl-names = "default"; @@ -240,9 +245,15 @@ status = "okay"; clock-frequency = <400000>; + /* + * The adv75xx resets its addresses to defaults during low power mode. + * Because we have two ADV7513 devices on the same bus, we must change + * both of them away from the defaults so that they do not conflict. + */ hdmi@3d { compatible = "adi,adv7513"; - reg = <0x3d>; + reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>; + reg-names = "main", "cec", "edid", "packet"; adi,input-depth = <8>; adi,input-colorspace = "rgb"; @@ -272,7 +283,8 @@ hdmi@39 { compatible = "adi,adv7513"; - reg = <0x39>; + reg = <0x39>, <0x29>, <0x49>, <0x59>; + reg-names = "main", "cec", "edid", "packet"; adi,input-depth = <8>; adi,input-colorspace = "rgb"; diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi index 268987ff0201..f44257dd86f6 100644 --- a/arch/arm/boot/dts/r8a7792.dtsi +++ b/arch/arm/boot/dts/r8a7792.dtsi @@ -85,6 +85,13 @@ clock-frequency = <0>; }; + pmu { + compatible = "arm,cortex-a15-pmu"; + interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>; + }; + /* External SCIF clock */ scif_clk: scif { compatible = "fixed-clock"; @@ -101,6 +108,16 @@ #size-cells = <2>; ranges; + rwdt: watchdog@e6020000 { + compatible = "renesas,r8a7792-wdt", + "renesas,rcar-gen2-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 402>; + power-domains = <&sysc R8A7792_PD_ALWAYS_ON>; + resets = <&cpg 402>; + status = "disabled"; + }; + gpio0: gpio@e6050000 { compatible = "renesas,gpio-r8a7792", "renesas,rcar-gen2-gpio"; @@ -341,7 +358,7 @@ smp-sram@0 { compatible = "renesas,smp-sram"; - reg = <0 0x10>; + reg = <0 0x100>; }; }; diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts index 9ed6961f2d9a..aa209f6e5d71 100644 --- a/arch/arm/boot/dts/r8a7793-gose.dts +++ b/arch/arm/boot/dts/r8a7793-gose.dts @@ -447,10 +447,9 @@ pinctrl-names = "default"; status = "okay"; - clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 726>, + clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&x13_clk>, <&x2_clk>; - clock-names = "du.0", "du.1", "lvds.0", - "dclkin.0", "dclkin.1"; + clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1"; ports { port@0 { @@ -458,6 +457,11 @@ remote-endpoint = <&adv7511_in>; }; }; + }; +}; + +&lvds0 { + ports { port@1 { lvds_connector: endpoint { }; @@ -595,6 +599,11 @@ status = "okay"; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &scif0 { pinctrl-0 = <&scif0_pins>; pinctrl-names = "default"; @@ -754,9 +763,6 @@ pinctrl-names = "default"; port { - #address-cells = <1>; - #size-cells = <0>; - vin0ep2: endpoint { remote-endpoint = <&adv7612_out>; bus-width = <24>; @@ -776,9 +782,6 @@ status = "okay"; port { - #address-cells = <1>; - #size-cells = <0>; - vin1ep: endpoint { remote-endpoint = <&adv7180_out>; bus-width = <8>; diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index f9c5a557107d..4abecfc0ca98 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -110,6 +110,13 @@ clock-frequency = <0>; }; + pmu { + compatible = "arm,cortex-a15-pmu"; + interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>; + }; + /* External SCIF clock */ scif_clk: scif { compatible = "fixed-clock"; @@ -126,6 +133,16 @@ #size-cells = <2>; ranges; + rwdt: watchdog@e6020000 { + compatible = "renesas,r8a7793-wdt", + "renesas,rcar-gen2-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 402>; + power-domains = <&sysc R8A7793_PD_ALWAYS_ON>; + resets = <&cpg 402>; + status = "disabled"; + }; + gpio0: gpio@e6050000 { compatible = "renesas,gpio-r8a7793", "renesas,rcar-gen2-gpio"; @@ -392,7 +409,7 @@ smp-sram@0 { compatible = "renesas,smp-sram"; - reg = <0 0x10>; + reg = <0 0x100>; }; }; @@ -1290,17 +1307,32 @@ resets = <&cpg 408>; }; + fdp1@fe940000 { + compatible = "renesas,fdp1"; + reg = <0 0xfe940000 0 0x2400>; + interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 119>; + power-domains = <&sysc R8A7793_PD_ALWAYS_ON>; + resets = <&cpg 119>; + }; + + fdp1@fe944000 { + compatible = "renesas,fdp1"; + reg = <0 0xfe944000 0 0x2400>; + interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 118>; + power-domains = <&sysc R8A7793_PD_ALWAYS_ON>; + resets = <&cpg 118>; + }; + du: display@feb00000 { compatible = "renesas,du-r8a7793"; - reg = <0 0xfeb00000 0 0x40000>, - <0 0xfeb90000 0 0x1c>; - reg-names = "du", "lvds.0"; + reg = <0 0xfeb00000 0 0x40000>; interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 724>, - <&cpg CPG_MOD 723>, - <&cpg CPG_MOD 726>; - clock-names = "du.0", "du.1", "lvds.0"; + <&cpg CPG_MOD 723>; + clock-names = "du.0", "du.1"; status = "disabled"; ports { @@ -1315,6 +1347,34 @@ port@1 { reg = <1>; du_out_lvds0: endpoint { + remote-endpoint = <&lvds0_in>; + }; + }; + }; + }; + + lvds0: lvds@feb90000 { + compatible = "renesas,r8a7793-lvds"; + reg = <0 0xfeb90000 0 0x1c>; + clocks = <&cpg CPG_MOD 726>; + power-domains = <&sysc R8A7793_PD_ALWAYS_ON>; + resets = <&cpg 726>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + lvds0_in: endpoint { + remote-endpoint = <&du_out_lvds0>; + }; + }; + port@1 { + reg = <1>; + lvds0_out: endpoint { }; }; }; diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts index 26a883484ea8..e17027532941 100644 --- a/arch/arm/boot/dts/r8a7794-alt.dts +++ b/arch/arm/boot/dts/r8a7794-alt.dts @@ -181,6 +181,12 @@ }; }; }; + + eeprom@50 { + compatible = "renesas,r1ex24002", "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; }; /* @@ -330,6 +336,11 @@ status = "okay"; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &sdhi0 { pinctrl-0 = <&sdhi0_pins>; pinctrl-1 = <&sdhi0_pins_uhs>; @@ -375,9 +386,6 @@ pinctrl-names = "default"; port { - #address-cells = <1>; - #size-cells = <0>; - vin0ep: endpoint { remote-endpoint = <&adv7180>; bus-width = <8>; diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts index 351cb3b3d966..7808aaee6644 100644 --- a/arch/arm/boot/dts/r8a7794-silk.dts +++ b/arch/arm/boot/dts/r8a7794-silk.dts @@ -475,9 +475,6 @@ pinctrl-names = "default"; port { - #address-cells = <1>; - #size-cells = <0>; - vin0ep: endpoint { remote-endpoint = <&adv7180>; bus-width = <8>; @@ -540,6 +537,11 @@ }; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &ssi1 { shared-pin; }; diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index d588efa6aeaa..736196903d22 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -103,6 +103,13 @@ clock-frequency = <0>; }; + pmu { + compatible = "arm,cortex-a7-pmu"; + interrupts-extended = <&gic GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>; + }; + /* External SCIF clock */ scif_clk: scif { compatible = "fixed-clock"; @@ -119,6 +126,16 @@ #size-cells = <2>; ranges; + rwdt: watchdog@e6020000 { + compatible = "renesas,r8a7794-wdt", + "renesas,rcar-gen2-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 402>; + power-domains = <&sysc R8A7794_PD_ALWAYS_ON>; + resets = <&cpg 402>; + status = "disabled"; + }; + gpio0: gpio@e6050000 { compatible = "renesas,gpio-r8a7794", "renesas,rcar-gen2-gpio"; @@ -348,7 +365,7 @@ smp-sram@0 { compatible = "renesas,smp-sram"; - reg = <0 0x10>; + reg = <0 0x100>; }; }; @@ -1323,6 +1340,15 @@ resets = <&cpg 128>; }; + fdp1@fe940000 { + compatible = "renesas,fdp1"; + reg = <0 0xfe940000 0 0x2400>; + interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 119>; + power-domains = <&sysc R8A7794_PD_ALWAYS_ON>; + resets = <&cpg 119>; + }; + du: display@feb00000 { compatible = "renesas,du-r8a7794"; reg = <0 0xfeb00000 0 0x40000>; diff --git a/arch/arm/boot/dts/rk3036.dtsi b/arch/arm/boot/dts/rk3036.dtsi index a97458112ff6..567a6a725f9c 100644 --- a/arch/arm/boot/dts/rk3036.dtsi +++ b/arch/arm/boot/dts/rk3036.dtsi @@ -197,6 +197,8 @@ reg = <0x10118300 0x100>; interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "vop_mmu"; + clocks = <&cru ACLK_LCDC>, <&cru HCLK_LCDC>; + clock-names = "aclk", "iface"; #iommu-cells = <0>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/rk322x.dtsi b/arch/arm/boot/dts/rk322x.dtsi index df1e47858675..be80e9a2c9af 100644 --- a/arch/arm/boot/dts/rk322x.dtsi +++ b/arch/arm/boot/dts/rk322x.dtsi @@ -584,6 +584,8 @@ reg = <0x20020800 0x100>; interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "vpu_mmu"; + clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>; + clock-names = "aclk", "iface"; iommu-cells = <0>; status = "disabled"; }; @@ -593,6 +595,8 @@ reg = <0x20030480 0x40>, <0x200304c0 0x40>; interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "vdec_mmu"; + clocks = <&cru ACLK_RKVDEC>, <&cru HCLK_RKVDEC>; + clock-names = "aclk", "iface"; iommu-cells = <0>; status = "disabled"; }; @@ -602,6 +606,8 @@ reg = <0x20053f00 0x100>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "vop_mmu"; + clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>; + clock-names = "aclk", "iface"; iommu-cells = <0>; status = "disabled"; }; @@ -611,6 +617,8 @@ reg = <0x20070800 0x100>; interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "iep_mmu"; + clocks = <&cru ACLK_IEP>, <&cru HCLK_IEP>; + clock-names = "aclk", "iface"; iommu-cells = <0>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/rk3288-phycore-som.dtsi b/arch/arm/boot/dts/rk3288-phycore-som.dtsi index f13bcb1cd3d9..aaab2d171ffe 100644 --- a/arch/arm/boot/dts/rk3288-phycore-som.dtsi +++ b/arch/arm/boot/dts/rk3288-phycore-som.dtsi @@ -151,6 +151,7 @@ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; enet-phy-lane-no-swap; + ti,clk-output-sel = <DP83867_CLK_O_SEL_CHN_A_TCLK>; }; }; }; diff --git a/arch/arm/boot/dts/rk3288-tinker.dts b/arch/arm/boot/dts/rk3288-tinker.dts index 346b0d8b474d..127488f9f174 100644 --- a/arch/arm/boot/dts/rk3288-tinker.dts +++ b/arch/arm/boot/dts/rk3288-tinker.dts @@ -49,6 +49,10 @@ model = "Rockchip RK3288 Tinker Board"; compatible = "asus,rk3288-tinker", "rockchip,rk3288"; + chosen { + stdout-path = "serial2:115200n8"; + }; + memory { reg = <0x0 0x0 0x0 0x80000000>; device_type = "memory"; diff --git a/arch/arm/boot/dts/rk3288-veyron-chromebook.dtsi b/arch/arm/boot/dts/rk3288-veyron-chromebook.dtsi index be487111d025..b16d570ff029 100644 --- a/arch/arm/boot/dts/rk3288-veyron-chromebook.dtsi +++ b/arch/arm/boot/dts/rk3288-veyron-chromebook.dtsi @@ -95,7 +95,8 @@ pinctrl-names = "default"; pinctrl-0 = <&bl_en>; pwms = <&pwm0 0 1000000 0>; - pwm-delay-us = <10000>; + post-pwm-on-delay-ms = <10>; + pwm-off-delay-ms = <10>; }; gpio-charger { diff --git a/arch/arm/boot/dts/rk3288-veyron-minnie.dts b/arch/arm/boot/dts/rk3288-veyron-minnie.dts index 544de6027aaa..4c5307e62001 100644 --- a/arch/arm/boot/dts/rk3288-veyron-minnie.dts +++ b/arch/arm/boot/dts/rk3288-veyron-minnie.dts @@ -123,6 +123,8 @@ 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255>; power-supply = <&backlight_regulator>; + post-pwm-on-delay-ms = <200>; + pwm-off-delay-ms = <200>; }; &emmc { diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index 354aff45c1af..d7e49d29ace5 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -959,6 +959,8 @@ reg = <0x0 0xff900800 0x0 0x40>; interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "iep_mmu"; + clocks = <&cru ACLK_IEP>, <&cru HCLK_IEP>; + clock-names = "aclk", "iface"; #iommu-cells = <0>; status = "disabled"; }; @@ -968,6 +970,8 @@ reg = <0x0 0xff914000 0x0 0x100>, <0x0 0xff915000 0x0 0x100>; interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "isp_mmu"; + clocks = <&cru ACLK_ISP>, <&cru HCLK_ISP>; + clock-names = "aclk", "iface"; #iommu-cells = <0>; rockchip,disable-mmu-reset; status = "disabled"; @@ -1027,6 +1031,8 @@ reg = <0x0 0xff930300 0x0 0x100>; interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "vopb_mmu"; + clocks = <&cru ACLK_VOP0>, <&cru HCLK_VOP0>; + clock-names = "aclk", "iface"; power-domains = <&power RK3288_PD_VIO>; #iommu-cells = <0>; status = "disabled"; @@ -1075,6 +1081,8 @@ reg = <0x0 0xff940300 0x0 0x100>; interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "vopl_mmu"; + clocks = <&cru ACLK_VOP1>, <&cru HCLK_VOP1>; + clock-names = "aclk", "iface"; power-domains = <&power RK3288_PD_VIO>; #iommu-cells = <0>; status = "disabled"; @@ -1206,6 +1214,8 @@ reg = <0x0 0xff9a0800 0x0 0x100>; interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "vpu_mmu"; + clocks = <&cru ACLK_VCODEC>, <&cru HCLK_VCODEC>; + clock-names = "aclk", "iface"; #iommu-cells = <0>; status = "disabled"; }; @@ -1215,6 +1225,8 @@ reg = <0x0 0xff9c0440 0x0 0x40>, <0x0 0xff9c0480 0x0 0x40>; interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "hevc_mmu"; + clocks = <&cru ACLK_HEVC>, <&cru HCLK_HEVC>; + clock-names = "aclk", "iface"; #iommu-cells = <0>; status = "disabled"; }; @@ -1848,16 +1860,16 @@ uart4 { uart4_xfer: uart4-xfer { - rockchip,pins = <5 12 3 &pcfg_pull_up>, - <5 13 3 &pcfg_pull_none>; + rockchip,pins = <5 15 3 &pcfg_pull_up>, + <5 14 3 &pcfg_pull_none>; }; uart4_cts: uart4-cts { - rockchip,pins = <5 14 3 &pcfg_pull_up>; + rockchip,pins = <5 12 3 &pcfg_pull_up>; }; uart4_rts: uart4-rts { - rockchip,pins = <5 15 3 &pcfg_pull_none>; + rockchip,pins = <5 13 3 &pcfg_pull_none>; }; }; diff --git a/arch/arm/boot/dts/s3c2416-smdk2416.dts b/arch/arm/boot/dts/s3c2416-smdk2416.dts index a1c9d8c695cc..5164386aff3a 100644 --- a/arch/arm/boot/dts/s3c2416-smdk2416.dts +++ b/arch/arm/boot/dts/s3c2416-smdk2416.dts @@ -12,14 +12,13 @@ model = "SMDK2416"; compatible = "samsung,s3c2416"; - memory { + memory@30000000 { + device_type = "memory"; reg = <0x30000000 0x4000000>; }; clocks { compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; xti: xti { compatible = "fixed-clock"; diff --git a/arch/arm/boot/dts/s3c2416.dtsi b/arch/arm/boot/dts/s3c2416.dtsi index 3c7385cab248..6adf64ea3ff2 100644 --- a/arch/arm/boot/dts/s3c2416.dtsi +++ b/arch/arm/boot/dts/s3c2416.dtsi @@ -18,9 +18,6 @@ }; cpus { - #address-cells = <1>; - #size-cells = <0>; - cpu { compatible = "arm,arm926ej-s"; }; @@ -30,7 +27,7 @@ compatible = "samsung,s3c2416-irq"; }; - clocks: clock-controller@0x4c000000 { + clocks: clock-controller@4c000000 { compatible = "samsung,s3c2416-clock"; reg = <0x4c000000 0x40>; #clock-cells = <1>; @@ -69,7 +66,7 @@ <&clocks SCLK_UART>; }; - uart_3: serial@5000C000 { + uart_3: serial@5000c000 { compatible = "samsung,s3c2440-uart"; reg = <0x5000C000 0x4000>; interrupts = <1 18 24 4>, <1 18 25 4>; @@ -80,7 +77,7 @@ status = "disabled"; }; - sdhci_1: sdhci@4AC00000 { + sdhci_1: sdhci@4ac00000 { compatible = "samsung,s3c6410-sdhci"; reg = <0x4AC00000 0x100>; interrupts = <0 0 21 3>; @@ -91,7 +88,7 @@ status = "disabled"; }; - sdhci_0: sdhci@4A800000 { + sdhci_0: sdhci@4a800000 { compatible = "samsung,s3c6410-sdhci"; reg = <0x4A800000 0x100>; interrupts = <0 0 20 3>; diff --git a/arch/arm/boot/dts/s3c24xx.dtsi b/arch/arm/boot/dts/s3c24xx.dtsi index 34c7fe6751cf..6d8dd3cdd3c0 100644 --- a/arch/arm/boot/dts/s3c24xx.dtsi +++ b/arch/arm/boot/dts/s3c24xx.dtsi @@ -5,11 +5,11 @@ * Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de> */ -#include "skeleton.dtsi" - / { compatible = "samsung,s3c24xx"; interrupt-parent = <&intc>; + #address-cells = <1>; + #size-cells = <1>; aliases { pinctrl0 = &pinctrl_0; diff --git a/arch/arm/boot/dts/s3c6410-mini6410.dts b/arch/arm/boot/dts/s3c6410-mini6410.dts index f68601bd9c91..0e159c884f97 100644 --- a/arch/arm/boot/dts/s3c6410-mini6410.dts +++ b/arch/arm/boot/dts/s3c6410-mini6410.dts @@ -19,7 +19,8 @@ model = "FriendlyARM Mini6410 board based on S3C6410"; compatible = "friendlyarm,mini6410", "samsung,s3c6410"; - memory { + memory@50000000 { + device_type = "memory"; reg = <0x50000000 0x10000000>; }; diff --git a/arch/arm/boot/dts/s3c6410-smdk6410.dts b/arch/arm/boot/dts/s3c6410-smdk6410.dts index b6b5afcd7602..a9a5689dc462 100644 --- a/arch/arm/boot/dts/s3c6410-smdk6410.dts +++ b/arch/arm/boot/dts/s3c6410-smdk6410.dts @@ -19,7 +19,8 @@ model = "SAMSUNG SMDK6410 board based on S3C6410"; compatible = "samsung,mini6410", "samsung,s3c6410"; - memory { + memory@50000000 { + device_type = "memory"; reg = <0x50000000 0x8000000>; }; diff --git a/arch/arm/boot/dts/s3c64xx.dtsi b/arch/arm/boot/dts/s3c64xx.dtsi index e2be3fbdd3f3..2e611df37911 100644 --- a/arch/arm/boot/dts/s3c64xx.dtsi +++ b/arch/arm/boot/dts/s3c64xx.dtsi @@ -13,10 +13,12 @@ * nodes can be added to this file. */ -#include "skeleton.dtsi" #include <dt-bindings/clock/samsung,s3c64xx-clock.h> / { + #address-cells = <1>; + #size-cells = <1>; + aliases { i2c0 = &i2c0; pinctrl0 = &pinctrl0; diff --git a/arch/arm/boot/dts/sh73a0.dtsi b/arch/arm/boot/dts/sh73a0.dtsi index 914a7c2a584f..c953648a5f41 100644 --- a/arch/arm/boot/dts/sh73a0.dtsi +++ b/arch/arm/boot/dts/sh73a0.dtsi @@ -22,7 +22,7 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu0: cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0>; @@ -31,7 +31,7 @@ power-domains = <&pd_a2sl>; next-level-cache = <&L2>; }; - cpu@1 { + cpu1: cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <1>; @@ -91,6 +91,7 @@ compatible = "arm,cortex-a9-pmu"; interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>; }; cmt1: timer@e6138000 { @@ -336,7 +337,7 @@ GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks SH73A0_CLK_SDHI1>; power-domains = <&pd_a3sp>; - toshiba,mmc-wrprotect-disable; + disable-wp; cap-sd-highspeed; status = "disabled"; }; @@ -348,7 +349,7 @@ GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks SH73A0_CLK_SDHI2>; power-domains = <&pd_a3sp>; - toshiba,mmc-wrprotect-disable; + disable-wp; cap-sd-highspeed; status = "disabled"; }; diff --git a/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts b/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts index 2459d133f1be..f50b19447de6 100644 --- a/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts +++ b/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts @@ -161,7 +161,7 @@ }; at24@50 { - compatible = "at24,24c01"; + compatible = "atmel,24c01"; pagesize = <8>; reg = <0x50>; }; @@ -213,7 +213,7 @@ #size-cells = <0>; reg = <6>; eeprom@51 { - compatible = "at,24c01"; + compatible = "atmel,24c01"; pagesize = <8>; reg = <0x51>; }; @@ -224,7 +224,7 @@ #size-cells = <0>; reg = <7>; eeprom@51 { - compatible = "at,24c01"; + compatible = "atmel,24c01"; pagesize = <8>; reg = <0x51>; }; diff --git a/arch/arm/boot/dts/ste-ccu8540-pinctrl.dtsi b/arch/arm/boot/dts/ste-ccu8540-pinctrl.dtsi deleted file mode 100644 index 52dba2e39c71..000000000000 --- a/arch/arm/boot/dts/ste-ccu8540-pinctrl.dtsi +++ /dev/null @@ -1,196 +0,0 @@ -/* - * Copyright 2012 ST-Ericsson - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ -#include "ste-nomadik-pinctrl.dtsi" - -/ { - soc { - pinctrl { - uart0 { - uart0_default_mux: uart0_mux { - default_mux { - function = "u0"; - groups = "u0_a_1"; - }; - }; - - uart0_default_mode: uart0_default { - default_cfg1 { - pins = "GPIO0", "GPIO2"; - ste,config = <&in_pu>; - }; - - default_cfg2 { - pins = "GPIO1", "GPIO3"; - ste,config = <&out_hi>; - }; - }; - - uart0_sleep_mode: uart0_sleep { - sleep_cfg1 { - pins = "GPIO0", "GPIO2"; - ste,config = <&slpm_in_pu>; - }; - - sleep_cfg2 { - pins = "GPIO1", "GPIO3"; - ste,config = <&slpm_out_hi>; - }; - }; - }; - - uart2 { - uart2_default_mode: uart2_default { - default_mux { - function = "u2"; - groups = "u2txrx_a_1"; - }; - - default_cfg1 { - pins = "GPIO120"; - ste,config = <&in_pu>; - }; - - default_cfg2 { - pins = "GPIO121"; - ste,config = <&out_hi>; - }; - }; - - uart2_sleep_mode: uart2_sleep { - sleep_cfg1 { - pins = "GPIO120"; - ste,config = <&slpm_in_pu>; - }; - - sleep_cfg2 { - pins = "GPIO121"; - ste,config = <&slpm_out_hi>; - }; - }; - }; - - i2c0 { - i2c0_default_mux: i2c_mux { - default_mux { - function = "i2c0"; - groups = "i2c0_a_1"; - }; - }; - - i2c0_default_mode: i2c_default { - default_cfg1 { - pins = "GPIO147", "GPIO148"; - ste,config = <&in_pu>; - }; - }; - - i2c0_sleep_mode: i2c_sleep { - sleep_cfg1 { - pins = "GPIO147", "GPIO148"; - ste,config = <&slpm_in_pu>; - }; - }; - }; - - i2c1 { - i2c1_default_mux: i2c_mux { - default_mux { - function = "i2c1"; - groups = "i2c1_b_2"; - }; - }; - - i2c1_default_mode: i2c_default { - default_cfg1 { - pins = "GPIO16", "GPIO17"; - ste,config = <&in_pu>; - }; - }; - - i2c1_sleep_mode: i2c_sleep { - sleep_cfg1 { - pins = "GPIO16", "GPIO17"; - ste,config = <&slpm_in_pu>; - }; - }; - }; - - i2c2 { - i2c2_default_mux: i2c_mux { - default_mux { - function = "i2c2"; - groups = "i2c2_b_2"; - }; - }; - - i2c2_default_mode: i2c_default { - default_cfg1 { - pins = "GPIO10", "GPIO11"; - ste,config = <&in_pu>; - }; - }; - - i2c2_sleep_mode: i2c_sleep { - sleep_cfg1 { - pins = "GPIO11", "GPIO11"; - ste,config = <&slpm_in_pu>; - }; - }; - }; - - i2c4 { - i2c4_default_mux: i2c_mux { - default_mux { - function = "i2c4"; - groups = "i2c4_b_2"; - }; - }; - - i2c4_default_mode: i2c_default { - default_cfg1 { - pins = "GPIO122", "GPIO123"; - ste,config = <&in_pu>; - }; - }; - - i2c4_sleep_mode: i2c_sleep { - sleep_cfg1 { - pins = "GPIO122", "GPIO123"; - ste,config = <&slpm_in_pu>; - }; - }; - }; - - i2c5 { - i2c5_default_mux: i2c_mux { - default_mux { - function = "i2c5"; - groups = "i2c5_c_2"; - }; - }; - - i2c5_default_mode: i2c_default { - default_cfg1 { - pins = "GPIO118", "GPIO119"; - ste,config = <&in_pu>; - }; - }; - - i2c5_sleep_mode: i2c_sleep { - sleep_cfg1 { - pins = "GPIO118", "GPIO119"; - ste,config = <&slpm_in_pu>; - }; - }; - }; - }; - }; -}; diff --git a/arch/arm/boot/dts/ste-ccu8540.dts b/arch/arm/boot/dts/ste-ccu8540.dts deleted file mode 100644 index 6eaaf638e52e..000000000000 --- a/arch/arm/boot/dts/ste-ccu8540.dts +++ /dev/null @@ -1,94 +0,0 @@ -/* - * Copyright 2013 ST-Ericsson AB - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ - -/dts-v1/; -#include "ste-dbx5x0.dtsi" -#include "ste-ccu8540-pinctrl.dtsi" - -/ { - model = "ST-Ericsson U8540 platform with Device Tree"; - compatible = "st-ericsson,ccu8540", "st-ericsson,u8540"; - - /* This stablilizes the serial port enumeration */ - aliases { - serial0 = &ux500_serial0; - serial1 = &ux500_serial1; - serial2 = &ux500_serial2; - }; - - memory@0 { - device_type = "memory"; - reg = <0x20000000 0x1f000000>, <0xc0000000 0x3f000000>; - }; - - soc { - pinctrl { - compatible = "stericsson,db8540-pinctrl"; - }; - - prcmu@80157000 { - reg = <0x80157000 0x2000>, <0x801b0000 0x8000>, <0x801b8000 0x3000>; - reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm"; - }; - - uart@80120000 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&uart0_default_mux>, <&uart0_default_mode>; - pinctrl-1 = <&uart0_sleep_mode>; - status = "okay"; - }; - - uart@80121000 { - status = "okay"; - }; - - uart@80007000 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&uart2_default_mode>; - pinctrl-1 = <&uart2_sleep_mode>; - status = "okay"; - }; - - i2c0: i2c@80004000 { - pinctrl-names = "default","sleep"; - pinctrl-0 = <&i2c0_default_mux>, <&i2c0_default_mode>; - pinctrl-1 = <&i2c0_sleep_mode>; - }; - - i2c1: i2c@80122000 { - pinctrl-names = "default","sleep"; - pinctrl-0 = <&i2c1_default_mux>, <&i2c1_default_mode>; - pinctrl-1 = <&i2c1_sleep_mode>; - }; - - i2c2: i2c@80128000 { - pinctrl-names = "default","sleep"; - pinctrl-0 = <&i2c2_default_mux>, <&i2c2_default_mode>; - pinctrl-1 = <&i2c2_sleep_mode>; - }; - - i2c3: i2c@80110000 { - status = "disabled"; - }; - - i2c4: i2c@8012a000 { - pinctrl-names = "default","sleep"; - pinctrl-0 = <&i2c4_default_mux>, <&i2c4_default_mode>; - pinctrl-1 = <&i2c4_sleep_mode>; - }; - - i2c5: i2c@80001000 { - pinctrl-names = "default","sleep"; - pinctrl-0 = <&i2c5_default_mux>, <&i2c5_default_mode>; - pinctrl-1 = <&i2c5_sleep_mode>; - }; - }; -}; diff --git a/arch/arm/boot/dts/ste-ccu9540.dts b/arch/arm/boot/dts/ste-ccu9540.dts deleted file mode 100644 index b3b9bb8e1aa8..000000000000 --- a/arch/arm/boot/dts/ste-ccu9540.dts +++ /dev/null @@ -1,79 +0,0 @@ -/* - * Copyright 2012 ST-Ericsson AB - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ - -/dts-v1/; -#include "ste-dbx5x0.dtsi" - -/ { - model = "ST-Ericsson CCU9540 platform with Device Tree"; - compatible = "st-ericsson,ccu9540", "st-ericsson,u9540"; - - /* This stablilizes the serial port enumeration */ - aliases { - serial0 = &ux500_serial0; - serial1 = &ux500_serial1; - serial2 = &ux500_serial2; - }; - - memory { - reg = <0x00000000 0x20000000>; - }; - - soc { - uart@80120000 { - status = "okay"; - }; - - uart@80121000 { - status = "okay"; - }; - - uart@80007000 { - status = "okay"; - }; - - // External Micro SD slot - sdi0_per1@80126000 { - arm,primecell-periphid = <0x10480180>; - max-frequency = <100000000>; - bus-width = <4>; - cap-sd-highspeed; - cap-mmc-highspeed; - vmmc-supply = <&ab8500_ldo_aux3_reg>; - - cd-gpios = <&gpio7 6 GPIO_ACTIVE_HIGH>; // 230 - cd-inverted; - - status = "okay"; - }; - - - // WLAN SDIO channel - sdi1_per2@80118000 { - arm,primecell-periphid = <0x10480180>; - max-frequency = <100000000>; - bus-width = <4>; - - status = "okay"; - }; - - // On-board eMMC - sdi4_per2@80114000 { - arm,primecell-periphid = <0x10480180>; - max-frequency = <100000000>; - bus-width = <8>; - cap-mmc-highspeed; - vmmc-supply = <&ab8500_ldo_aux2_reg>; - - status = "okay"; - }; - }; -}; diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts index ade1d0d4e5f4..b0b94d053098 100644 --- a/arch/arm/boot/dts/ste-snowball.dts +++ b/arch/arm/boot/dts/ste-snowball.dts @@ -46,35 +46,35 @@ #size-cells = <0>; button@1 { - debounce_interval = <50>; + debounce-interval = <50>; wakeup-source; linux,code = <2>; label = "userpb"; gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>; }; button@2 { - debounce_interval = <50>; + debounce-interval = <50>; wakeup-source; linux,code = <3>; label = "extkb1"; gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>; }; button@3 { - debounce_interval = <50>; + debounce-interval = <50>; wakeup-source; linux,code = <4>; label = "extkb2"; gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>; }; button@4 { - debounce_interval = <50>; + debounce-interval = <50>; wakeup-source; linux,code = <5>; label = "extkb3"; gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; }; button@5 { - debounce_interval = <50>; + debounce-interval = <50>; wakeup-source; linux,code = <6>; label = "extkb4"; diff --git a/arch/arm/boot/dts/stih407-family.dtsi b/arch/arm/boot/dts/stih407-family.dtsi index f7362c31de29..9e29a4499938 100644 --- a/arch/arm/boot/dts/stih407-family.dtsi +++ b/arch/arm/boot/dts/stih407-family.dtsi @@ -206,19 +206,19 @@ vtg_main: sti-vtg-main@8d02800 { compatible = "st,vtg"; reg = <0x8d02800 0x200>; - interrupts = <GIC_SPI 108 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; }; vtg_aux: sti-vtg-aux@8d00200 { compatible = "st,vtg"; reg = <0x8d00200 0x100>; - interrupts = <GIC_SPI 109 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; }; serial@9830000 { compatible = "st,asc"; reg = <0x9830000 0x2c>; - interrupts = <GIC_SPI 122 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; /* Pinctrl moved out to a per-board configuration */ @@ -228,7 +228,7 @@ serial@9831000 { compatible = "st,asc"; reg = <0x9831000 0x2c>; - interrupts = <GIC_SPI 123 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_serial1>; clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; @@ -239,7 +239,7 @@ serial@9832000 { compatible = "st,asc"; reg = <0x9832000 0x2c>; - interrupts = <GIC_SPI 124 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_serial2>; clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; @@ -251,7 +251,7 @@ sbc_serial0: serial@9530000 { compatible = "st,asc"; reg = <0x9530000 0x2c>; - interrupts = <GIC_SPI 138 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sbc_serial0>; clocks = <&clk_sysin>; @@ -262,7 +262,7 @@ serial@9531000 { compatible = "st,asc"; reg = <0x9531000 0x2c>; - interrupts = <GIC_SPI 139 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sbc_serial1>; clocks = <&clk_sysin>; @@ -574,7 +574,7 @@ status = "disabled"; reg = <0x09060000 0x7ff>, <0x9061008 0x20>; reg-names = "mmc", "top-mmc-delay"; - interrupts = <GIC_SPI 92 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "mmcirq"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_mmc0>; @@ -589,7 +589,7 @@ status = "disabled"; reg = <0x09080000 0x7ff>; reg-names = "mmc"; - interrupts = <GIC_SPI 90 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "mmcirq"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sd1>; @@ -623,7 +623,7 @@ compatible = "st,ahci"; reg = <0x9b20000 0x1000>; - interrupts = <GIC_SPI 159 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "hostc"; phys = <&phy_port0 PHY_TYPE_SATA>; @@ -646,7 +646,7 @@ compatible = "st,ahci"; reg = <0x9b28000 0x1000>; - interrupts = <GIC_SPI 170 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "hostc"; phys = <&phy_port1 PHY_TYPE_SATA>; @@ -687,7 +687,7 @@ dwc3: dwc3@9900000 { compatible = "snps,dwc3"; reg = <0x09900000 0x100000>; - interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; dr_mode = "host"; phy-names = "usb2-phy", "usb3-phy"; phys = <&usb2_picophy0>, @@ -701,7 +701,7 @@ compatible = "st,sti-pwm"; #pwm-cells = <2>; reg = <0x9810000 0x68>; - interrupts = <GIC_SPI 128 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pwm0_chan0_default>; clock-names = "pwm"; @@ -716,7 +716,7 @@ compatible = "st,sti-pwm"; #pwm-cells = <2>; reg = <0x9510000 0x68>; - interrupts = <GIC_SPI 131 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pwm1_chan0_default &pinctrl_pwm1_chan1_default @@ -755,8 +755,8 @@ resets = <&softreset STIH407_ETH1_SOFTRESET>; reset-names = "stmmaceth"; - interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>, - <GIC_SPI 99 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "macirq", "eth_wake_irq"; /* DMA Bus Mode */ @@ -787,7 +787,7 @@ mailbox0: mailbox@8f00000 { compatible = "st,stih407-mailbox"; reg = <0x8f00000 0x1000>; - interrupts = <GIC_SPI 1 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; #mbox-cells = <2>; mbox-name = "a9"; status = "okay"; @@ -857,7 +857,7 @@ <&clk_s_c0_flexgen CLK_EXT2F_A9>, <&clk_s_c0_flexgen CLK_EXT2F_A9>, <&clk_s_c0_flexgen CLK_EXT2F_A9>; - interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; dma-channels = <16>; #dma-cells = <3>; }; @@ -875,7 +875,7 @@ <&clk_s_c0_flexgen CLK_TX_ICN_DMU>, <&clk_s_c0_flexgen CLK_EXT2F_A9>; - interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; dma-channels = <16>; #dma-cells = <3>; @@ -890,7 +890,7 @@ <0x8e77000 0x1000>, <0x8e78000 0x8000>; reg-names = "slimcore", "dmem", "peripherals", "imem"; - interrupts = <GIC_SPI 9 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; dma-channels = <16>; #dma-cells = <3>; clocks = <&clk_s_c0_flexgen CLK_FDMA>, @@ -910,7 +910,7 @@ assigned-clock-parents = <0>, <&clk_s_d0_quadfs 0>; assigned-clock-rates = <50000000>; reg = <0x8d80000 0x158>; - interrupts = <GIC_SPI 84 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; dmas = <&fdma0 2 0 1>; dma-names = "tx"; @@ -926,7 +926,7 @@ assigned-clock-parents = <0>, <&clk_s_d0_quadfs 1>; assigned-clock-rates = <50000000>; reg = <0x8d81000 0x158>; - interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; dmas = <&fdma0 3 0 1>; dma-names = "tx"; @@ -942,7 +942,7 @@ assigned-clock-parents = <0>, <&clk_s_d0_quadfs 2>; assigned-clock-rates = <50000000>; reg = <0x8d82000 0x158>; - interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; dmas = <&fdma0 4 0 1>; dma-names = "tx"; @@ -958,7 +958,7 @@ assigned-clock-parents = <0>, <&clk_s_d0_quadfs 3>; assigned-clock-rates = <50000000>; reg = <0x8d85000 0x158>; - interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; dmas = <&fdma0 7 0 1>; dma-names = "tx"; @@ -970,7 +970,7 @@ #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; reg = <0x8d83000 0x158>; - interrupts = <GIC_SPI 87 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; dmas = <&fdma0 5 0 1>; dma-names = "rx"; @@ -982,7 +982,7 @@ #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; reg = <0x8d84000 0x158>; - interrupts = <GIC_SPI 88 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; dmas = <&fdma0 6 0 1>; dma-names = "rx"; diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/stih407-pinctrl.dtsi index 53c6888d1fc0..e393519fb84c 100644 --- a/arch/arm/boot/dts/stih407-pinctrl.dtsi +++ b/arch/arm/boot/dts/stih407-pinctrl.dtsi @@ -52,7 +52,7 @@ st,syscfg = <&syscfg_sbc>; reg = <0x0961f080 0x4>; reg-names = "irqmux"; - interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "irqmux"; ranges = <0 0x09610000 0x6000>; @@ -376,7 +376,7 @@ st,syscfg = <&syscfg_front>; reg = <0x0920f080 0x4>; reg-names = "irqmux"; - interrupts = <GIC_SPI 189 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "irqmux"; ranges = <0 0x09200000 0x10000>; @@ -936,7 +936,7 @@ st,syscfg = <&syscfg_front>; reg = <0x0921f080 0x4>; reg-names = "irqmux"; - interrupts = <GIC_SPI 190 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "irqmux"; ranges = <0 0x09210000 0x10000>; @@ -969,7 +969,7 @@ st,syscfg = <&syscfg_rear>; reg = <0x0922f080 0x4>; reg-names = "irqmux"; - interrupts = <GIC_SPI 191 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "irqmux"; ranges = <0 0x09220000 0x6000>; @@ -1164,7 +1164,7 @@ st,syscfg = <&syscfg_flash>; reg = <0x0923f080 0x4>; reg-names = "irqmux"; - interrupts = <GIC_SPI 192 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "irqmux"; ranges = <0 0x09230000 0x3000>; diff --git a/arch/arm/boot/dts/stih407.dtsi b/arch/arm/boot/dts/stih407.dtsi index 57efc87dec2b..5b7951ffc350 100644 --- a/arch/arm/boot/dts/stih407.dtsi +++ b/arch/arm/boot/dts/stih407.dtsi @@ -108,7 +108,7 @@ reg = <0x8d04000 0x1000>; reg-names = "hdmi-reg"; #sound-dai-cells = <0>; - interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "irq"; clock-names = "pix", "tmds", diff --git a/arch/arm/boot/dts/stih410.dtsi b/arch/arm/boot/dts/stih410.dtsi index 3313005ee15c..888548ea9b5c 100644 --- a/arch/arm/boot/dts/stih410.dtsi +++ b/arch/arm/boot/dts/stih410.dtsi @@ -43,7 +43,7 @@ ohci0: usb@9a03c00 { compatible = "st,st-ohci-300x"; reg = <0x9a03c00 0x100>; - interrupts = <GIC_SPI 180 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>, <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>; resets = <&powerdown STIH407_USB2_PORT0_POWERDOWN>, @@ -58,7 +58,7 @@ ehci0: usb@9a03e00 { compatible = "st,st-ehci-300x"; reg = <0x9a03e00 0x100>; - interrupts = <GIC_SPI 151 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb0>; clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>, @@ -75,7 +75,7 @@ ohci1: usb@9a83c00 { compatible = "st,st-ohci-300x"; reg = <0x9a83c00 0x100>; - interrupts = <GIC_SPI 181 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>, <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>; resets = <&powerdown STIH407_USB2_PORT1_POWERDOWN>, @@ -90,7 +90,7 @@ ehci1: usb@9a83e00 { compatible = "st,st-ehci-300x"; reg = <0x9a83e00 0x100>; - interrupts = <GIC_SPI 153 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb1>; clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>, @@ -202,7 +202,7 @@ reg = <0x8d04000 0x1000>; reg-names = "hdmi-reg"; #sound-dai-cells = <0>; - interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "irq"; clock-names = "pix", "tmds", @@ -254,7 +254,7 @@ bdisp0:bdisp@9f10000 { compatible = "st,stih407-bdisp"; reg = <0x9f10000 0x1000>; - interrupts = <GIC_SPI 38 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; clock-names = "bdisp"; clocks = <&clk_s_c0_flexgen CLK_IC_BDISP_0>; }; @@ -263,8 +263,8 @@ compatible = "st,st-hva"; reg = <0x8c85000 0x400>, <0x6000000 0x40000>; reg-names = "hva_registers", "hva_esram"; - interrupts = <GIC_SPI 58 IRQ_TYPE_NONE>, - <GIC_SPI 59 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; clock-names = "clk_hva"; clocks = <&clk_s_c0_flexgen CLK_HVA>; }; @@ -292,7 +292,7 @@ reg = <0x94a087c 0x64>; clocks = <&clk_sysin>; clock-names = "cec-clk"; - interrupts = <GIC_SPI 140 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "cec-irq"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_cec0_default>; diff --git a/arch/arm/boot/dts/stihxxx-b2120.dtsi b/arch/arm/boot/dts/stihxxx-b2120.dtsi index c67edb1a8121..4dedfcb0fcb3 100644 --- a/arch/arm/boot/dts/stihxxx-b2120.dtsi +++ b/arch/arm/boot/dts/stihxxx-b2120.dtsi @@ -154,8 +154,8 @@ reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>; reg-names = "c8sectpfe", "c8sectpfe-ram"; - interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, - <GIC_SPI 35 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "c8sectpfe-error-irq", "c8sectpfe-idle-irq"; pinctrl-0 = <&pinctrl_tsin0_serial>; diff --git a/arch/arm/boot/dts/stm32f469-disco.dts b/arch/arm/boot/dts/stm32f469-disco.dts index 2f76726bf335..3ee768cb86fc 100644 --- a/arch/arm/boot/dts/stm32f469-disco.dts +++ b/arch/arm/boot/dts/stm32f469-disco.dts @@ -46,7 +46,7 @@ */ /dts-v1/; -#include "stm32f429.dtsi" +#include "stm32f469.dtsi" #include "stm32f469-pinctrl.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> @@ -112,7 +112,7 @@ vcc5v_otg: vcc5v-otg-regulator { compatible = "regulator-fixed"; enable-active-high; - gpio = <&gpiob 2 0>; + gpio = <&gpiob 2 GPIO_ACTIVE_HIGH>; regulator-name = "vcc5_host1"; regulator-always-on; }; @@ -126,6 +126,55 @@ clock-frequency = <8000000>; }; +&dsi { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi_in: endpoint { + remote-endpoint = <<dc_out_dsi>; + }; + }; + + port@1 { + reg = <1>; + dsi_out: endpoint { + remote-endpoint = <&dsi_panel_in>; + }; + }; + }; + + panel-dsi@0 { + compatible = "orisetech,otm8009a"; + reg = <0>; /* dsi virtual channel (0..3) */ + reset-gpios = <&gpioh 7 GPIO_ACTIVE_LOW>; + status = "okay"; + + port { + dsi_panel_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + }; +}; + +<dc { + dma-ranges; + status = "okay"; + + port { + ltdc_out_dsi: endpoint@0 { + remote-endpoint = <&dsi_in>; + }; + }; +}; + &rtc { status = "okay"; }; diff --git a/arch/arm/boot/dts/stm32f469.dtsi b/arch/arm/boot/dts/stm32f469.dtsi new file mode 100644 index 000000000000..5ae5213f68cb --- /dev/null +++ b/arch/arm/boot/dts/stm32f469.dtsi @@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */ +/* Copyright (C) STMicroelectronics 2017 - All Rights Reserved */ + +#include "stm32f429.dtsi" + +/ { + soc { + dsi: dsi@40016c00 { + compatible = "st,stm32-dsi"; + reg = <0x40016c00 0x800>; + interrupts = <92>; + resets = <&rcc STM32F4_APB2_RESET(DSI)>; + reset-names = "apb"; + clocks = <&rcc 1 CLK_F469_DSI>, <&clk_hse>; + clock-names = "pclk", "ref"; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm/boot/dts/stm32f746-disco.dts b/arch/arm/boot/dts/stm32f746-disco.dts index be94c6ad7e94..f9ad71f7c807 100644 --- a/arch/arm/boot/dts/stm32f746-disco.dts +++ b/arch/arm/boot/dts/stm32f746-disco.dts @@ -90,6 +90,14 @@ clock-frequency = <25000000>; }; +&i2c1 { + pinctrl-0 = <&i2c1_pins_b>; + pinctrl-names = "default"; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; +}; + &sdio1 { status = "okay"; vmmc-supply = <&mmc_vcard>; diff --git a/arch/arm/boot/dts/stm32f746.dtsi b/arch/arm/boot/dts/stm32f746.dtsi index 4be2ee575b19..1479e3eb05fa 100644 --- a/arch/arm/boot/dts/stm32f746.dtsi +++ b/arch/arm/boot/dts/stm32f746.dtsi @@ -345,6 +345,42 @@ status = "disabled"; }; + i2c2: i2c@40005800 { + compatible = "st,stm32f7-i2c"; + reg = <0x40005800 0x400>; + interrupts = <33>, + <34>; + resets = <&rcc STM32F7_APB1_RESET(I2C2)>; + clocks = <&rcc 1 CLK_I2C2>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@40005C00 { + compatible = "st,stm32f7-i2c"; + reg = <0x40005C00 0x400>; + interrupts = <72>, + <73>; + resets = <&rcc STM32F7_APB1_RESET(I2C3)>; + clocks = <&rcc 1 CLK_I2C3>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c4: i2c@40006000 { + compatible = "st,stm32f7-i2c"; + reg = <0x40006000 0x400>; + interrupts = <95>, + <96>; + resets = <&rcc STM32F7_APB1_RESET(I2C4)>; + clocks = <&rcc 1 CLK_I2C4>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + cec: cec@40006c00 { compatible = "st,stm32-cec"; reg = <0x40006C00 0x400>; diff --git a/arch/arm/boot/dts/stm32f769-disco.dts b/arch/arm/boot/dts/stm32f769-disco.dts index 2241eecdabfe..677276ba4dbe 100644 --- a/arch/arm/boot/dts/stm32f769-disco.dts +++ b/arch/arm/boot/dts/stm32f769-disco.dts @@ -111,6 +111,14 @@ clock-frequency = <25000000>; }; +&i2c1 { + pinctrl-0 = <&i2c1_pins_b>; + pinctrl-names = "default"; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; +}; + &rtc { status = "okay"; }; diff --git a/arch/arm/boot/dts/stm32h743-pinctrl.dtsi b/arch/arm/boot/dts/stm32h743-pinctrl.dtsi index 0f15dfb98381..24be8e63dec8 100644 --- a/arch/arm/boot/dts/stm32h743-pinctrl.dtsi +++ b/arch/arm/boot/dts/stm32h743-pinctrl.dtsi @@ -163,6 +163,16 @@ #interrupt-cells = <2>; }; + i2c1_pins_a: i2c1@0 { + pins { + pinmux = <STM32_PINMUX('B', 6, AF4)>, /* I2C1_SCL */ + <STM32_PINMUX('B', 7, AF4)>; /* I2C1_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + usart1_pins: usart1@0 { pins1 { pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */ diff --git a/arch/arm/boot/dts/stm32h743.dtsi b/arch/arm/boot/dts/stm32h743.dtsi index 2bb103e1194d..637beffe5067 100644 --- a/arch/arm/boot/dts/stm32h743.dtsi +++ b/arch/arm/boot/dts/stm32h743.dtsi @@ -86,6 +86,7 @@ pwm { compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; status = "disabled"; }; @@ -130,6 +131,42 @@ clocks = <&rcc USART2_CK>; }; + i2c1: i2c@40005400 { + compatible = "st,stm32f7-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40005400 0x400>; + interrupts = <31>, + <32>; + resets = <&rcc STM32H7_APB1L_RESET(I2C1)>; + clocks = <&rcc I2C1_CK>; + status = "disabled"; + }; + + i2c2: i2c@40005800 { + compatible = "st,stm32f7-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40005800 0x400>; + interrupts = <33>, + <34>; + resets = <&rcc STM32H7_APB1L_RESET(I2C2)>; + clocks = <&rcc I2C2_CK>; + status = "disabled"; + }; + + i2c3: i2c@40005C00 { + compatible = "st,stm32f7-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40005C00 0x400>; + interrupts = <72>, + <73>; + resets = <&rcc STM32H7_APB1L_RESET(I2C3)>; + clocks = <&rcc I2C3_CK>; + status = "disabled"; + }; + dac: dac@40007400 { compatible = "st,stm32h7-dac-core"; reg = <0x40007400 0x400>; @@ -323,6 +360,18 @@ status = "disabled"; }; + i2c4: i2c@58001C00 { + compatible = "st,stm32f7-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x58001C00 0x400>; + interrupts = <95>, + <96>; + resets = <&rcc STM32H7_APB4_RESET(I2C4)>; + clocks = <&rcc I2C4_CK>; + status = "disabled"; + }; + lptimer2: timer@58002400 { #address-cells = <1>; #size-cells = <0>; @@ -334,6 +383,7 @@ pwm { compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; status = "disabled"; }; @@ -360,6 +410,7 @@ pwm { compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; status = "disabled"; }; @@ -381,6 +432,7 @@ pwm { compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; status = "disabled"; }; }; @@ -396,6 +448,7 @@ pwm { compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/stm32h743i-eval.dts b/arch/arm/boot/dts/stm32h743i-eval.dts index c7187e18ea16..3f8e0c4a998d 100644 --- a/arch/arm/boot/dts/stm32h743i-eval.dts +++ b/arch/arm/boot/dts/stm32h743i-eval.dts @@ -92,6 +92,14 @@ clock-frequency = <25000000>; }; +&i2c1 { + pinctrl-0 = <&i2c1_pins_a>; + pinctrl-names = "default"; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; +}; + &rtc { status = "okay"; }; diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi index c0743305f31b..4839db146890 100644 --- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi +++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi @@ -7,11 +7,13 @@ / { soc { - pinctrl: pin-controller { + pinctrl: pin-controller@50002000 { #address-cells = <1>; #size-cells = <1>; compatible = "st,stm32mp157-pinctrl"; ranges = <0 0x50002000 0xa400>; + interrupt-parent = <&exti>; + st,syscfg = <&exti 0x60 0xff>; pins-are-numbered; gpioa: gpio@50002000 { @@ -20,7 +22,7 @@ interrupt-controller; #interrupt-cells = <2>; reg = <0x0 0x400>; - clocks = <&clk_pll3_p>; + clocks = <&rcc GPIOA>; st,bank-name = "GPIOA"; ngpios = <16>; gpio-ranges = <&pinctrl 0 0 16>; @@ -32,7 +34,7 @@ interrupt-controller; #interrupt-cells = <2>; reg = <0x1000 0x400>; - clocks = <&clk_pll3_p>; + clocks = <&rcc GPIOB>; st,bank-name = "GPIOB"; ngpios = <16>; gpio-ranges = <&pinctrl 0 16 16>; @@ -44,7 +46,7 @@ interrupt-controller; #interrupt-cells = <2>; reg = <0x2000 0x400>; - clocks = <&clk_pll3_p>; + clocks = <&rcc GPIOC>; st,bank-name = "GPIOC"; ngpios = <16>; gpio-ranges = <&pinctrl 0 32 16>; @@ -56,7 +58,7 @@ interrupt-controller; #interrupt-cells = <2>; reg = <0x3000 0x400>; - clocks = <&clk_pll3_p>; + clocks = <&rcc GPIOD>; st,bank-name = "GPIOD"; ngpios = <16>; gpio-ranges = <&pinctrl 0 48 16>; @@ -68,7 +70,7 @@ interrupt-controller; #interrupt-cells = <2>; reg = <0x4000 0x400>; - clocks = <&clk_pll3_p>; + clocks = <&rcc GPIOE>; st,bank-name = "GPIOE"; ngpios = <16>; gpio-ranges = <&pinctrl 0 64 16>; @@ -80,7 +82,7 @@ interrupt-controller; #interrupt-cells = <2>; reg = <0x5000 0x400>; - clocks = <&clk_pll3_p>; + clocks = <&rcc GPIOF>; st,bank-name = "GPIOF"; ngpios = <16>; gpio-ranges = <&pinctrl 0 80 16>; @@ -92,7 +94,7 @@ interrupt-controller; #interrupt-cells = <2>; reg = <0x6000 0x400>; - clocks = <&clk_pll3_p>; + clocks = <&rcc GPIOG>; st,bank-name = "GPIOG"; ngpios = <16>; gpio-ranges = <&pinctrl 0 96 16>; @@ -104,7 +106,7 @@ interrupt-controller; #interrupt-cells = <2>; reg = <0x7000 0x400>; - clocks = <&clk_pll3_p>; + clocks = <&rcc GPIOH>; st,bank-name = "GPIOH"; ngpios = <16>; gpio-ranges = <&pinctrl 0 112 16>; @@ -116,7 +118,7 @@ interrupt-controller; #interrupt-cells = <2>; reg = <0x8000 0x400>; - clocks = <&clk_pll3_p>; + clocks = <&rcc GPIOI>; st,bank-name = "GPIOI"; ngpios = <16>; gpio-ranges = <&pinctrl 0 128 16>; @@ -128,7 +130,7 @@ interrupt-controller; #interrupt-cells = <2>; reg = <0x9000 0x400>; - clocks = <&clk_pll3_p>; + clocks = <&rcc GPIOJ>; st,bank-name = "GPIOJ"; ngpios = <16>; gpio-ranges = <&pinctrl 0 144 16>; @@ -140,13 +142,124 @@ interrupt-controller; #interrupt-cells = <2>; reg = <0xa000 0x400>; - clocks = <&clk_pll3_p>; + clocks = <&rcc GPIOK>; st,bank-name = "GPIOK"; ngpios = <8>; gpio-ranges = <&pinctrl 0 160 8>; }; - uart4_pins_a: uart4@0 { + cec_pins_a: cec-0 { + pins { + pinmux = <STM32_PINMUX('A', 15, AF4)>; + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + i2c1_pins_a: i2c1-0 { + pins { + pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */ + <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + i2c2_pins_a: i2c2-0 { + pins { + pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */ + <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + i2c5_pins_a: i2c5-0 { + pins { + pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */ + <STM32_PINMUX('A', 12, AF4)>; /* I2C5_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + pwm2_pins_a: pwm2-0 { + pins { + pinmux = <STM32_PINMUX('A', 3, AF1)>; /* TIM2_CH4 */ + bias-pull-down; + drive-push-pull; + slew-rate = <0>; + }; + }; + + pwm8_pins_a: pwm8-0 { + pins { + pinmux = <STM32_PINMUX('I', 2, AF3)>; /* TIM8_CH4 */ + bias-pull-down; + drive-push-pull; + slew-rate = <0>; + }; + }; + + pwm12_pins_a: pwm12-0 { + pins { + pinmux = <STM32_PINMUX('H', 6, AF2)>; /* TIM12_CH1 */ + bias-pull-down; + drive-push-pull; + slew-rate = <0>; + }; + }; + + qspi_clk_pins_a: qspi-clk-0 { + pins { + pinmux = <STM32_PINMUX('F', 10, AF9)>; /* QSPI_CLK */ + bias-disable; + drive-push-pull; + slew-rate = <3>; + }; + }; + + qspi_bk1_pins_a: qspi-bk1-0 { + pins1 { + pinmux = <STM32_PINMUX('F', 8, AF10)>, /* QSPI_BK1_IO0 */ + <STM32_PINMUX('F', 9, AF10)>, /* QSPI_BK1_IO1 */ + <STM32_PINMUX('F', 7, AF9)>, /* QSPI_BK1_IO2 */ + <STM32_PINMUX('F', 6, AF9)>; /* QSPI_BK1_IO3 */ + bias-disable; + drive-push-pull; + slew-rate = <3>; + }; + pins2 { + pinmux = <STM32_PINMUX('B', 6, AF10)>; /* QSPI_BK1_NCS */ + bias-pull-up; + drive-push-pull; + slew-rate = <3>; + }; + }; + + qspi_bk2_pins_a: qspi-bk2-0 { + pins1 { + pinmux = <STM32_PINMUX('H', 2, AF9)>, /* QSPI_BK2_IO0 */ + <STM32_PINMUX('H', 3, AF9)>, /* QSPI_BK2_IO1 */ + <STM32_PINMUX('G', 10, AF11)>, /* QSPI_BK2_IO2 */ + <STM32_PINMUX('G', 7, AF11)>; /* QSPI_BK2_IO3 */ + bias-disable; + drive-push-pull; + slew-rate = <3>; + }; + pins2 { + pinmux = <STM32_PINMUX('C', 0, AF10)>; /* QSPI_BK2_NCS */ + bias-pull-up; + drive-push-pull; + slew-rate = <3>; + }; + }; + + uart4_pins_a: uart4-0 { pins1 { pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */ bias-disable; @@ -160,12 +273,14 @@ }; }; - pinctrl_z: pin-controller-z { + pinctrl_z: pin-controller-z@54004000 { #address-cells = <1>; #size-cells = <1>; compatible = "st,stm32mp157-z-pinctrl"; ranges = <0 0x54004000 0x400>; pins-are-numbered; + interrupt-parent = <&exti>; + st,syscfg = <&exti 0x60 0xff>; status = "disabled"; gpioz: gpio@54004000 { @@ -174,12 +289,22 @@ interrupt-controller; #interrupt-cells = <2>; reg = <0 0x400>; - clocks = <&clk_pll2_p>; + clocks = <&rcc GPIOZ>; st,bank-name = "GPIOZ"; st,bank-ioport = <11>; ngpios = <8>; gpio-ranges = <&pinctrl_z 0 400 8>; }; + + i2c4_pins_a: i2c4-0 { + pins { + pinmux = <STM32_PINMUX('Z', 4, AF6)>, /* I2C4_SCL */ + <STM32_PINMUX('Z', 5, AF6)>; /* I2C4_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; }; }; }; diff --git a/arch/arm/boot/dts/stm32mp157c-ed1.dts b/arch/arm/boot/dts/stm32mp157c-ed1.dts index 9f90337a22e3..ae336530b59b 100644 --- a/arch/arm/boot/dts/stm32mp157c-ed1.dts +++ b/arch/arm/boot/dts/stm32mp157c-ed1.dts @@ -16,13 +16,56 @@ stdout-path = "serial0:115200n8"; }; - memory { + memory@c0000000 { reg = <0xC0000000 0x40000000>; }; aliases { serial0 = &uart4; }; + + reg11: reg11 { + compatible = "regulator-fixed"; + regulator-name = "reg11"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + reg18: reg18 { + compatible = "regulator-fixed"; + regulator-name = "reg18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vdd_usb: vdd-usb { + compatible = "regulator-fixed"; + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; +}; + +&rng1 { + status = "okay"; +}; + +&timers6 { + status = "okay"; + timer@5 { + status = "okay"; + }; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; }; &uart4 { @@ -30,3 +73,15 @@ pinctrl-0 = <&uart4_pins_a>; status = "okay"; }; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +}; diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts index 57e6dbc52e09..9382d8063031 100644 --- a/arch/arm/boot/dts/stm32mp157c-ev1.dts +++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts @@ -19,3 +19,90 @@ serial0 = &uart4; }; }; + +&cec { + pinctrl-names = "default"; + pinctrl-0 = <&cec_pins_a>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; +}; + +&i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; +}; + +&qspi { + pinctrl-names = "default"; + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>; + reg = <0x58003000 0x1000>, <0x70000000 0x4000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash0: mx66l51235l@0 { + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + #address-cells = <1>; + #size-cells = <1>; + }; + + flash1: mx66l51235l@1 { + reg = <1>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&timers2 { + status = "disabled"; + pwm { + pinctrl-0 = <&pwm2_pins_a>; + pinctrl-names = "default"; + status = "okay"; + }; + timer@1 { + status = "okay"; + }; +}; + +&timers8 { + status = "disabled"; + pwm { + pinctrl-0 = <&pwm8_pins_a>; + pinctrl-names = "default"; + status = "okay"; + }; + timer@7 { + status = "okay"; + }; +}; + +&timers12 { + status = "disabled"; + pwm { + pinctrl-0 = <&pwm12_pins_a>; + pinctrl-names = "default"; + status = "okay"; + }; + timer@11 { + status = "okay"; + }; +}; + +&usbphyc { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/stm32mp157c.dtsi index 9e17e42b02b2..7d1753893453 100644 --- a/arch/arm/boot/dts/stm32mp157c.dtsi +++ b/arch/arm/boot/dts/stm32mp157c.dtsi @@ -4,6 +4,8 @@ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics. */ #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/stm32mp1-clks.h> +#include <dt-bindings/reset/stm32mp1-resets.h> / { #address-cells = <1>; @@ -71,12 +73,6 @@ clock-frequency = <24000000>; }; - clk_pll_per: clk-pll-per { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <64000000>; - }; - clk_hsi: clk-hsi { #clock-cells = <0>; compatible = "fixed-clock"; @@ -100,24 +96,6 @@ compatible = "fixed-clock"; clock-frequency = <4000000>; }; - - clk_pclk1: clk-pclk1 { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <86000000>; - }; - - clk_pll3_p: clk-pll3_p { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <172000000>; - }; - - clk_pll2_p: clk-pll2_p { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <264000000>; - }; }; soc { @@ -127,67 +105,736 @@ interrupt-parent = <&intc>; ranges; + timers2: timer@40000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000000 0x400>; + clocks = <&rcc TIM2_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@1 { + compatible = "st,stm32h7-timer-trigger"; + reg = <1>; + status = "disabled"; + }; + }; + + timers3: timer@40001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001000 0x400>; + clocks = <&rcc TIM3_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@2 { + compatible = "st,stm32h7-timer-trigger"; + reg = <2>; + status = "disabled"; + }; + }; + + timers4: timer@40002000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40002000 0x400>; + clocks = <&rcc TIM4_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@3 { + compatible = "st,stm32h7-timer-trigger"; + reg = <3>; + status = "disabled"; + }; + }; + + timers5: timer@40003000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40003000 0x400>; + clocks = <&rcc TIM5_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@4 { + compatible = "st,stm32h7-timer-trigger"; + reg = <4>; + status = "disabled"; + }; + }; + + timers6: timer@40004000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40004000 0x400>; + clocks = <&rcc TIM6_K>; + clock-names = "int"; + status = "disabled"; + + timer@5 { + compatible = "st,stm32h7-timer-trigger"; + reg = <5>; + status = "disabled"; + }; + }; + + timers7: timer@40005000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40005000 0x400>; + clocks = <&rcc TIM7_K>; + clock-names = "int"; + status = "disabled"; + + timer@6 { + compatible = "st,stm32h7-timer-trigger"; + reg = <6>; + status = "disabled"; + }; + }; + + timers12: timer@40006000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40006000 0x400>; + clocks = <&rcc TIM12_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@11 { + compatible = "st,stm32h7-timer-trigger"; + reg = <11>; + status = "disabled"; + }; + }; + + timers13: timer@40007000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40007000 0x400>; + clocks = <&rcc TIM13_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@12 { + compatible = "st,stm32h7-timer-trigger"; + reg = <12>; + status = "disabled"; + }; + }; + + timers14: timer@40008000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40008000 0x400>; + clocks = <&rcc TIM14_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@13 { + compatible = "st,stm32h7-timer-trigger"; + reg = <13>; + status = "disabled"; + }; + }; + + lptimer1: timer@40009000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-lptimer"; + reg = <0x40009000 0x400>; + clocks = <&rcc LPTIM1_K>; + clock-names = "mux"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + status = "disabled"; + }; + + trigger@0 { + compatible = "st,stm32-lptimer-trigger"; + reg = <0>; + status = "disabled"; + }; + + counter { + compatible = "st,stm32-lptimer-counter"; + status = "disabled"; + }; + }; + usart2: serial@4000e000 { compatible = "st,stm32h7-uart"; reg = <0x4000e000 0x400>; - interrupts = <GIC_SPI 38 IRQ_TYPE_NONE>; - clocks = <&clk_pclk1>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc USART2_K>; status = "disabled"; }; usart3: serial@4000f000 { compatible = "st,stm32h7-uart"; reg = <0x4000f000 0x400>; - interrupts = <GIC_SPI 39 IRQ_TYPE_NONE>; - clocks = <&clk_pclk1>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc USART3_K>; status = "disabled"; }; uart4: serial@40010000 { compatible = "st,stm32h7-uart"; reg = <0x40010000 0x400>; - interrupts = <GIC_SPI 52 IRQ_TYPE_NONE>; - clocks = <&clk_pclk1>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc UART4_K>; status = "disabled"; }; uart5: serial@40011000 { compatible = "st,stm32h7-uart"; reg = <0x40011000 0x400>; - interrupts = <GIC_SPI 53 IRQ_TYPE_NONE>; - clocks = <&clk_pclk1>; + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc UART5_K>; status = "disabled"; }; + i2c1: i2c@40012000 { + compatible = "st,stm32f7-i2c"; + reg = <0x40012000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C1_K>; + resets = <&rcc I2C1_R>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@40013000 { + compatible = "st,stm32f7-i2c"; + reg = <0x40013000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C2_K>; + resets = <&rcc I2C2_R>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@40014000 { + compatible = "st,stm32f7-i2c"; + reg = <0x40014000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C3_K>; + resets = <&rcc I2C3_R>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c5: i2c@40015000 { + compatible = "st,stm32f7-i2c"; + reg = <0x40015000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C5_K>; + resets = <&rcc I2C5_R>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + cec: cec@40016000 { + compatible = "st,stm32-cec"; + reg = <0x40016000 0x400>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc CEC_K>, <&clk_lse>; + clock-names = "cec", "hdmi-cec"; + status = "disabled"; + }; + + dac: dac@40017000 { + compatible = "st,stm32h7-dac-core"; + reg = <0x40017000 0x400>; + clocks = <&rcc DAC12>; + clock-names = "pclk"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + dac1: dac@1 { + compatible = "st,stm32-dac"; + #io-channels-cells = <1>; + reg = <1>; + status = "disabled"; + }; + + dac2: dac@2 { + compatible = "st,stm32-dac"; + #io-channels-cells = <1>; + reg = <2>; + status = "disabled"; + }; + }; + uart7: serial@40018000 { compatible = "st,stm32h7-uart"; reg = <0x40018000 0x400>; - interrupts = <GIC_SPI 82 IRQ_TYPE_NONE>; - clocks = <&clk_pclk1>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc UART7_K>; status = "disabled"; }; uart8: serial@40019000 { compatible = "st,stm32h7-uart"; reg = <0x40019000 0x400>; - interrupts = <GIC_SPI 83 IRQ_TYPE_NONE>; - clocks = <&clk_pclk1>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc UART8_K>; status = "disabled"; }; + timers1: timer@44000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x44000000 0x400>; + clocks = <&rcc TIM1_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@0 { + compatible = "st,stm32h7-timer-trigger"; + reg = <0>; + status = "disabled"; + }; + }; + + timers8: timer@44001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x44001000 0x400>; + clocks = <&rcc TIM8_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@7 { + compatible = "st,stm32h7-timer-trigger"; + reg = <7>; + status = "disabled"; + }; + }; + usart6: serial@44003000 { compatible = "st,stm32h7-uart"; reg = <0x44003000 0x400>; - interrupts = <GIC_SPI 71 IRQ_TYPE_NONE>; - clocks = <&clk_pclk1>; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc USART6_K>; status = "disabled"; }; + timers15: timer@44006000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x44006000 0x400>; + clocks = <&rcc TIM15_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@14 { + compatible = "st,stm32h7-timer-trigger"; + reg = <14>; + status = "disabled"; + }; + }; + + timers16: timer@44007000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x44007000 0x400>; + clocks = <&rcc TIM16_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + timer@15 { + compatible = "st,stm32h7-timer-trigger"; + reg = <15>; + status = "disabled"; + }; + }; + + timers17: timer@44008000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x44008000 0x400>; + clocks = <&rcc TIM17_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@16 { + compatible = "st,stm32h7-timer-trigger"; + reg = <16>; + status = "disabled"; + }; + }; + + dma1: dma@48000000 { + compatible = "st,stm32-dma"; + reg = <0x48000000 0x400>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc DMA1>; + #dma-cells = <4>; + st,mem2mem; + dma-requests = <8>; + }; + + dma2: dma@48001000 { + compatible = "st,stm32-dma"; + reg = <0x48001000 0x400>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc DMA2>; + #dma-cells = <4>; + st,mem2mem; + dma-requests = <8>; + }; + + dmamux1: dma-router@48002000 { + compatible = "st,stm32h7-dmamux"; + reg = <0x48002000 0x1c>; + #dma-cells = <3>; + dma-requests = <128>; + dma-masters = <&dma1 &dma2>; + dma-channels = <16>; + clocks = <&rcc DMAMUX>; + }; + + rcc: rcc@50000000 { + compatible = "st,stm32mp1-rcc", "syscon"; + reg = <0x50000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + exti: interrupt-controller@5000d000 { + compatible = "st,stm32mp1-exti", "syscon"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x5000d000 0x400>; + }; + + lptimer2: timer@50021000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-lptimer"; + reg = <0x50021000 0x400>; + clocks = <&rcc LPTIM2_K>; + clock-names = "mux"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + status = "disabled"; + }; + + trigger@1 { + compatible = "st,stm32-lptimer-trigger"; + reg = <1>; + status = "disabled"; + }; + + counter { + compatible = "st,stm32-lptimer-counter"; + status = "disabled"; + }; + }; + + lptimer3: timer@50022000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-lptimer"; + reg = <0x50022000 0x400>; + clocks = <&rcc LPTIM3_K>; + clock-names = "mux"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + status = "disabled"; + }; + + trigger@2 { + compatible = "st,stm32-lptimer-trigger"; + reg = <2>; + status = "disabled"; + }; + }; + + lptimer4: timer@50023000 { + compatible = "st,stm32-lptimer"; + reg = <0x50023000 0x400>; + clocks = <&rcc LPTIM4_K>; + clock-names = "mux"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + status = "disabled"; + }; + }; + + lptimer5: timer@50024000 { + compatible = "st,stm32-lptimer"; + reg = <0x50024000 0x400>; + clocks = <&rcc LPTIM5_K>; + clock-names = "mux"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + status = "disabled"; + }; + }; + + vrefbuf: vrefbuf@50025000 { + compatible = "st,stm32-vrefbuf"; + reg = <0x50025000 0x8>; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2500000>; + clocks = <&rcc VREF>; + status = "disabled"; + }; + + cryp1: cryp@54001000 { + compatible = "st,stm32mp1-cryp"; + reg = <0x54001000 0x400>; + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc CRYP1>; + resets = <&rcc CRYP1_R>; + status = "disabled"; + }; + + rng1: rng@54003000 { + compatible = "st,stm32-rng"; + reg = <0x54003000 0x400>; + clocks = <&rcc RNG1_K>; + resets = <&rcc RNG1_R>; + status = "disabled"; + }; + + mdma1: dma@58000000 { + compatible = "st,stm32h7-mdma"; + reg = <0x58000000 0x1000>; + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc MDMA>; + #dma-cells = <5>; + dma-channels = <32>; + dma-requests = <48>; + }; + + qspi: qspi@58003000 { + compatible = "st,stm32f469-qspi"; + reg = <0x58003000 0x1000>, <0x70000000 0x10000000>; + reg-names = "qspi", "qspi_mm"; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc QSPI_K>; + resets = <&rcc QSPI_R>; + status = "disabled"; + }; + + crc1: crc@58009000 { + compatible = "st,stm32f7-crc"; + reg = <0x58009000 0x400>; + clocks = <&rcc CRC1>; + status = "disabled"; + }; + + usbh_ohci: usbh-ohci@5800c000 { + compatible = "generic-ohci"; + reg = <0x5800c000 0x1000>; + clocks = <&rcc USBH>; + resets = <&rcc USBH_R>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + usbh_ehci: usbh-ehci@5800d000 { + compatible = "generic-ehci"; + reg = <0x5800d000 0x1000>; + clocks = <&rcc USBH>; + resets = <&rcc USBH_R>; + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; + companion = <&usbh_ohci>; + status = "disabled"; + }; + + dsi: dsi@5a000000 { + compatible = "st,stm32-dsi"; + reg = <0x5a000000 0x800>; + clocks = <&rcc DSI_K>, <&clk_hse>, <&rcc DSI_PX>; + clock-names = "pclk", "ref", "px_clk"; + resets = <&rcc DSI_R>; + reset-names = "apb"; + status = "disabled"; + }; + + ltdc: display-controller@5a001000 { + compatible = "st,stm32-ltdc"; + reg = <0x5a001000 0x400>; + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc LTDC_PX>; + clock-names = "lcd"; + resets = <&rcc LTDC_R>; + status = "disabled"; + }; + + usbphyc: usbphyc@5a006000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32mp1-usbphyc"; + reg = <0x5a006000 0x1000>; + clocks = <&rcc USBPHY_K>; + resets = <&rcc USBPHY_R>; + status = "disabled"; + + usbphyc_port0: usb-phy@0 { + #phy-cells = <0>; + reg = <0>; + }; + + usbphyc_port1: usb-phy@1 { + #phy-cells = <1>; + reg = <1>; + }; + }; + usart1: serial@5c000000 { compatible = "st,stm32h7-uart"; reg = <0x5c000000 0x400>; - interrupts = <GIC_SPI 37 IRQ_TYPE_NONE>; - clocks = <&clk_pclk1>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc USART1_K>; + status = "disabled"; + }; + + i2c4: i2c@5c002000 { + compatible = "st,stm32f7-i2c"; + reg = <0x5c002000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C4_K>; + resets = <&rcc I2C4_R>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c6: i2c@5c009000 { + compatible = "st,stm32f7-i2c"; + reg = <0x5c009000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C6_K>; + resets = <&rcc I2C6_R>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi index 77e8436beed4..3a1c6b45c9a1 100644 --- a/arch/arm/boot/dts/sun4i-a10.dtsi +++ b/arch/arm/boot/dts/sun4i-a10.dtsi @@ -76,7 +76,7 @@ allwinner,pipeline = "de_fe0-de_be0-lcd0-hdmi"; clocks = <&ccu CLK_AHB_LCD0>, <&ccu CLK_AHB_HDMI0>, <&ccu CLK_AHB_DE_BE0>, <&ccu CLK_AHB_DE_FE0>, - <&ccu CLK_DE_BE0>, <&ccu CLK_AHB_DE_FE0>, + <&ccu CLK_DE_BE0>, <&ccu CLK_DE_FE0>, <&ccu CLK_TCON0_CH1>, <&ccu CLK_HDMI>, <&ccu CLK_DRAM_DE_FE0>, <&ccu CLK_DRAM_DE_BE0>; status = "disabled"; @@ -88,7 +88,7 @@ allwinner,pipeline = "de_fe0-de_be0-lcd0"; clocks = <&ccu CLK_AHB_LCD0>, <&ccu CLK_AHB_DE_BE0>, <&ccu CLK_AHB_DE_FE0>, <&ccu CLK_DE_BE0>, - <&ccu CLK_AHB_DE_FE0>, <&ccu CLK_TCON0_CH0>, + <&ccu CLK_DE_FE0>, <&ccu CLK_TCON0_CH0>, <&ccu CLK_DRAM_DE_FE0>, <&ccu CLK_DRAM_DE_BE0>; status = "disabled"; }; @@ -99,7 +99,7 @@ allwinner,pipeline = "de_fe0-de_be0-lcd0-tve0"; clocks = <&ccu CLK_AHB_TVE0>, <&ccu CLK_AHB_LCD0>, <&ccu CLK_AHB_DE_BE0>, <&ccu CLK_AHB_DE_FE0>, - <&ccu CLK_DE_BE0>, <&ccu CLK_AHB_DE_FE0>, + <&ccu CLK_DE_BE0>, <&ccu CLK_DE_FE0>, <&ccu CLK_TCON0_CH1>, <&ccu CLK_DRAM_TVE0>, <&ccu CLK_DRAM_DE_FE0>, <&ccu CLK_DRAM_DE_BE0>; status = "disabled"; diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb-emmc.dts b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb-emmc.dts new file mode 100644 index 000000000000..81ebc97b76ee --- /dev/null +++ b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb-emmc.dts @@ -0,0 +1,37 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Device Tree Source for A20-Olimex-SOM-EVB-eMMC Board + * + * Copyright (C) 2018 Olimex Ltd. + * Author: Stefan Mavrodiev <stefan@olimex.com> + */ + +/dts-v1/; +#include "sun7i-a20-olimex-som-evb.dts" + +/ { + + model = "Olimex A20-Olimex-SOM-EVB-eMMC"; + compatible = "olimex,a20-olimex-som-evb-emmc", "allwinner,sun7i-a20"; + + mmc2_pwrseq: mmc2_pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&pio 2 18 GPIO_ACTIVE_LOW>; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_a>; + vmmc-supply = <®_vcc3v3>; + mmc-pwrseq = <&mmc2_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + emmc: emmc@0 { + reg = <0>; + compatible = "mmc-card"; + broken-hpi; + }; +}; diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts b/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts index eae8e267b9ef..3d7b5c848fef 100644 --- a/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts +++ b/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts @@ -172,8 +172,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/sun8i-a23-a33.dtsi index 971f9be699a7..44f3cad3de75 100644 --- a/arch/arm/boot/dts/sun8i-a23-a33.dtsi +++ b/arch/arm/boot/dts/sun8i-a23-a33.dtsi @@ -198,6 +198,8 @@ clock-names = "ahb", "mod"; resets = <&ccu RST_BUS_NAND>; reset-names = "ahb"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins &nand_pins_cs0 &nand_pins_rb0>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; @@ -315,6 +317,37 @@ bias-pull-up; }; + nand_pins: nand-pins { + pins = "PC0", "PC1", "PC2", "PC5", + "PC8", "PC9", "PC10", "PC11", + "PC12", "PC13", "PC14", "PC15"; + function = "nand0"; + }; + + nand_pins_cs0: nand-pins-cs0 { + pins = "PC4"; + function = "nand0"; + bias-pull-up; + }; + + nand_pins_cs1: nand-pins-cs1 { + pins = "PC3"; + function = "nand0"; + bias-pull-up; + }; + + nand_pins_rb0: nand-pins-rb0 { + pins = "PC6"; + function = "nand0"; + bias-pull-up; + }; + + nand_pins_rb1: nand-pins-rb1 { + pins = "PC7"; + function = "nand0"; + bias-pull-up; + }; + pwm0_pins: pwm0 { pins = "PH0"; function = "pwm0"; diff --git a/arch/arm/boot/dts/sun8i-a33.dtsi b/arch/arm/boot/dts/sun8i-a33.dtsi index a21f2ed07a52..8d278ee001e9 100644 --- a/arch/arm/boot/dts/sun8i-a33.dtsi +++ b/arch/arm/boot/dts/sun8i-a33.dtsi @@ -236,6 +236,11 @@ #address-cells = <1>; #size-cells = <0>; reg = <1>; + + tcon0_out_dsi: endpoint@1 { + reg = <1>; + remote-endpoint = <&dsi_in_tcon0>; + }; }; }; }; @@ -280,6 +285,45 @@ #io-channel-cells = <0>; }; + dsi: dsi@1ca0000 { + compatible = "allwinner,sun6i-a31-mipi-dsi"; + reg = <0x01ca0000 0x1000>; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_MIPI_DSI>, + <&ccu CLK_DSI_SCLK>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_MIPI_DSI>; + phys = <&dphy>; + phy-names = "dphy"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + dsi_in_tcon0: endpoint { + remote-endpoint = <&tcon0_out_dsi>; + }; + }; + }; + }; + + dphy: d-phy@1ca1000 { + compatible = "allwinner,sun6i-a31-mipi-dphy"; + reg = <0x01ca1000 0x1000>; + clocks = <&ccu CLK_BUS_MIPI_DSI>, + <&ccu CLK_DSI_DPHY>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_MIPI_DSI>; + status = "disabled"; + #phy-cells = <0>; + }; + fe0: display-frontend@1e00000 { compatible = "allwinner,sun8i-a33-display-frontend"; reg = <0x01e00000 0x20000>; diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi index 568307639be8..2be23d600957 100644 --- a/arch/arm/boot/dts/sun8i-a83t.dtsi +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi @@ -66,6 +66,8 @@ compatible = "arm,cortex-a7"; device_type = "cpu"; operating-points-v2 = <&cpu0_opp_table>; + cci-control-port = <&cci_control0>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <0>; }; @@ -73,6 +75,8 @@ compatible = "arm,cortex-a7"; device_type = "cpu"; operating-points-v2 = <&cpu0_opp_table>; + cci-control-port = <&cci_control0>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <1>; }; @@ -80,6 +84,8 @@ compatible = "arm,cortex-a7"; device_type = "cpu"; operating-points-v2 = <&cpu0_opp_table>; + cci-control-port = <&cci_control0>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <2>; }; @@ -87,6 +93,8 @@ compatible = "arm,cortex-a7"; device_type = "cpu"; operating-points-v2 = <&cpu0_opp_table>; + cci-control-port = <&cci_control0>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <3>; }; @@ -96,6 +104,8 @@ compatible = "arm,cortex-a7"; device_type = "cpu"; operating-points-v2 = <&cpu1_opp_table>; + cci-control-port = <&cci_control1>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <0x100>; }; @@ -103,6 +113,8 @@ compatible = "arm,cortex-a7"; device_type = "cpu"; operating-points-v2 = <&cpu1_opp_table>; + cci-control-port = <&cci_control1>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <0x101>; }; @@ -110,6 +122,8 @@ compatible = "arm,cortex-a7"; device_type = "cpu"; operating-points-v2 = <&cpu1_opp_table>; + cci-control-port = <&cci_control1>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <0x102>; }; @@ -117,6 +131,8 @@ compatible = "arm,cortex-a7"; device_type = "cpu"; operating-points-v2 = <&cpu1_opp_table>; + cci-control-port = <&cci_control1>; + enable-method = "allwinner,sun8i-a83t-smp"; reg = <0x103>; }; }; @@ -349,6 +365,44 @@ }; }; + cpucfg@1700000 { + compatible = "allwinner,sun8i-a83t-cpucfg"; + reg = <0x01700000 0x400>; + }; + + cci@1790000 { + compatible = "arm,cci-400"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x01790000 0x10000>; + ranges = <0x0 0x01790000 0x10000>; + + cci_control0: slave-if@4000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x4000 0x1000>; + }; + + cci_control1: slave-if@5000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x5000 0x1000>; + }; + + pmu@9000 { + compatible = "arm,cci-400-pmu,r1"; + reg = <0x9000 0x5000>; + interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + syscon: syscon@1c00000 { compatible = "allwinner,sun8i-a83t-system-controller", "syscon"; @@ -492,6 +546,11 @@ #size-cells = <0>; }; + sid: eeprom@1c14000 { + compatible = "allwinner,sun8i-a83t-sid"; + reg = <0x1c14000 0x400>; + }; + usb_otg: usb@1c19000 { compatible = "allwinner,sun8i-a83t-musb", "allwinner,sun8i-a33-musb"; @@ -928,6 +987,11 @@ #reset-cells = <1>; }; + r_cpucfg@1f01c00 { + compatible = "allwinner,sun8i-a83t-r-cpucfg"; + reg = <0x1f01c00 0x400>; + }; + r_pio: pinctrl@1f02c00 { compatible = "allwinner,sun8i-a83t-r-pinctrl"; reg = <0x01f02c00 0x400>; diff --git a/arch/arm/boot/dts/sun8i-h2-plus-libretech-all-h3-cc.dts b/arch/arm/boot/dts/sun8i-h2-plus-libretech-all-h3-cc.dts new file mode 100644 index 000000000000..4db0d4bb65eb --- /dev/null +++ b/arch/arm/boot/dts/sun8i-h2-plus-libretech-all-h3-cc.dts @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2018 Chen-Yu Tsai <wens@csie.org> + */ + +/dts-v1/; +#include "sun8i-h3.dtsi" +#include "sunxi-libretech-all-h3-cc.dtsi" + +/ { + model = "Libre Computer Board ALL-H3-CC H2+"; + compatible = "libretech,all-h3-cc-h2-plus", "allwinner,sun8i-h2-plus"; +}; diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts index 0bc031fe4c56..84cd9c061227 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts @@ -89,6 +89,23 @@ gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>; }; + reg_vdd_cpux: vdd-cpux-regulator { + compatible = "regulator-gpio"; + regulator-name = "vdd-cpux"; + regulator-type = "voltage"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-ramp-delay = <50>; /* 4ms */ + + gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + enable-active-high; + gpios-states = <1>; + states = <1100000 0 + 1300000 1>; + }; + wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; @@ -96,6 +113,10 @@ }; }; +&cpu0 { + cpu-supply = <®_vdd_cpux>; +}; + &ehci0 { status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts index b20a710da7bc..a8b2f0f1c11d 100644 --- a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts +++ b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts @@ -6,213 +6,9 @@ /dts-v1/; #include "sun8i-h3.dtsi" - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> +#include "sunxi-libretech-all-h3-cc.dtsi" / { model = "Libre Computer Board ALL-H3-CC H3"; compatible = "libretech,all-h3-cc-h3", "allwinner,sun8i-h3"; - - aliases { - ethernet0 = &emac; - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - connector { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_con_in: endpoint { - remote-endpoint = <&hdmi_out_con>; - }; - }; - }; - - leds { - compatible = "gpio-leds"; - - pwr_led { - label = "librecomputer:green:pwr"; - gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ - default-state = "on"; - }; - - status_led { - label = "librecomputer:blue:status"; - gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */ - }; - }; - - gpio_keys { - compatible = "gpio-keys"; - - power { - label = "power"; - linux,code = <KEY_POWER>; - gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ - }; - }; - - reg_vcc1v2: vcc1v2 { - compatible = "regulator-fixed"; - regulator-name = "vcc1v2"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <®_vcc5v0>; - gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ - enable-active-high; - }; - - reg_vcc3v3: vcc3v3 { - compatible = "regulator-fixed"; - regulator-name = "vcc3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - vin-supply = <®_vcc5v0>; - }; - - /* This represents the board's 5V input */ - reg_vcc5v0: vcc5v0 { - compatible = "regulator-fixed"; - regulator-name = "vcc5v0"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - }; - - reg_vcc_dram: vcc-dram { - compatible = "regulator-fixed"; - regulator-name = "vcc-dram"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <®_vcc5v0>; - gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */ - enable-active-high; - }; - - reg_vcc_io: vcc-io { - compatible = "regulator-fixed"; - regulator-name = "vcc-io"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <®_vcc3v3>; - gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */ - }; - - reg_vdd_cpux: vdd-cpux { - compatible = "regulator-fixed"; - regulator-name = "vdd-cpux"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <®_vcc5v0>; - gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ - enable-active-high; - }; -}; - -&codec { - allwinner,audio-routing = - "Line Out", "LINEOUT", - "MIC1", "Mic", - "Mic", "MBIAS"; - status = "okay"; -}; - -&de { - status = "okay"; -}; - -&ehci0 { - status = "okay"; -}; - -&ehci1 { - status = "okay"; -}; - -&ehci2 { - status = "okay"; -}; - -&ehci3 { - status = "okay"; -}; - -&emac { - phy-handle = <&int_mii_phy>; - phy-mode = "mii"; - allwinner,leds-active-low; - status = "okay"; -}; - -&hdmi { - status = "okay"; -}; - -&hdmi_out { - hdmi_out_con: endpoint { - remote-endpoint = <&hdmi_con_in>; - }; -}; - -&ir { - pinctrl-names = "default"; - pinctrl-0 = <&ir_pins_a>; - status = "okay"; -}; - -&mmc0 { - vmmc-supply = <®_vcc_io>; - bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ - status = "okay"; -}; - -&ohci0 { - status = "okay"; -}; - -&ohci1 { - status = "okay"; -}; - -&ohci2 { - status = "okay"; -}; - -&ohci3 { - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; - status = "okay"; -}; - -&usb_otg { - dr_mode = "host"; - status = "okay"; -}; - -&usbphy { - /* VBUS on USB ports are always on */ - usb0_vbus-supply = <®_vcc5v0>; - usb1_vbus-supply = <®_vcc5v0>; - usb2_vbus-supply = <®_vcc5v0>; - usb3_vbus-supply = <®_vcc5v0>; - status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts index 3328fe583c9b..245fd658defb 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts @@ -99,6 +99,27 @@ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; }; }; + + reg_vdd_cpux: vdd-cpux-regulator { + compatible = "regulator-gpio"; + regulator-name = "vdd-cpux"; + regulator-type = "voltage"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-ramp-delay = <50>; /* 4ms */ + + gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + enable-active-high; + gpios-states = <0x1>; + states = <1100000 0x0 + 1300000 0x1>; + }; +}; + +&cpu0 { + cpu-supply = <®_vdd_cpux>; }; &de { @@ -117,6 +138,7 @@ phy-handle = <&int_mii_phy>; phy-mode = "mii"; allwinner,leds-active-low; + status = "okay"; }; &hdmi { diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts index cea4d647ecbf..46240334128f 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts @@ -113,6 +113,10 @@ status = "okay"; }; +&cpu0 { + cpu-supply = <®_vdd_cpux>; +}; + &ehci0 { status = "okay"; }; @@ -182,6 +186,30 @@ }; }; +&r_i2c { + status = "okay"; + + reg_vdd_cpux: regulator@65 { + compatible = "silergy,sy8106a"; + reg = <0x65>; + regulator-name = "vdd-cpux"; + silergy,fixed-microvolt = <1200000>; + /* + * The datasheet uses 1.1V as the minimum value of VDD-CPUX, + * however both the Armbian DVFS table and the official one + * have operating points with voltage under 1.1V, and both + * DVFS table are known to work properly at the lowest + * operating point. + * + * Use 1.0V as the minimum voltage instead. + */ + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + }; +}; + &r_pio { leds_r_opc: led_pins { pins = "PL10"; diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi index 10da8ed7db81..41d57c76f290 100644 --- a/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -43,32 +43,62 @@ #include "sunxi-h3-h5.dtsi" / { + cpu0_opp_table: opp_table0 { + compatible = "operating-points-v2"; + opp-shared; + + opp@648000000 { + opp-hz = /bits/ 64 <648000000>; + opp-microvolt = <1040000 1040000 1300000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp@816000000 { + opp-hz = /bits/ 64 <816000000>; + opp-microvolt = <1100000 1100000 1300000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + + opp@1008000000 { + opp-hz = /bits/ 64 <1008000000>; + opp-microvolt = <1200000 1200000 1300000>; + clock-latency-ns = <244144>; /* 8 32k periods */ + }; + }; + cpus { #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu0: cpu@0 { compatible = "arm,cortex-a7"; device_type = "cpu"; reg = <0>; + clocks = <&ccu CLK_CPUX>; + clock-names = "cpu"; + operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; }; cpu@1 { compatible = "arm,cortex-a7"; device_type = "cpu"; reg = <1>; + operating-points-v2 = <&cpu0_opp_table>; }; cpu@2 { compatible = "arm,cortex-a7"; device_type = "cpu"; reg = <2>; + operating-points-v2 = <&cpu0_opp_table>; }; cpu@3 { compatible = "arm,cortex-a7"; device_type = "cpu"; reg = <3>; + operating-points-v2 = <&cpu0_opp_table>; }; }; diff --git a/arch/arm/boot/dts/sun8i-r16-nintendo-nes-classic.dts b/arch/arm/boot/dts/sun8i-r16-nintendo-nes-classic.dts new file mode 100644 index 000000000000..fc0658cfa319 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-r16-nintendo-nes-classic.dts @@ -0,0 +1,56 @@ +// SPDX-License-Identifier: GPL-2.0 OR X11 +/* Copyright (c) 2016 FUKAUMI Naoki <naobsd@gmail.com> */ + +/dts-v1/; +#include "sun8i-a33.dtsi" +#include "sunxi-common-regulators.dtsi" + +/ { + model = "Nintendo NES Classic Edition"; + compatible = "nintendo,nes-classic", "allwinner,sun8i-r16", + "allwinner,sun8i-a33"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + /* + * UART0 is available on two ports: PB and PF, both are accessible. + * PF can also be used for the SD card so PB is preferred. + */ + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&nfc { + status = "okay"; + + /* 2Gb Macronix MX30LF2G18AC (3V) */ + nand@0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + allwinner,rb = <0>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <16>; + nand-ecc-step-size = <1024>; + }; +}; + +&usb_otg { + status = "okay"; + dr_mode = "otg"; +}; + +&usbphy { + /* VBUS is always on because it is wired to the power supply */ + usb1_vbus-supply = <®_vcc5v0>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun8i-r16-nintendo-super-nes-classic.dts b/arch/arm/boot/dts/sun8i-r16-nintendo-super-nes-classic.dts new file mode 100644 index 000000000000..80761d7904ec --- /dev/null +++ b/arch/arm/boot/dts/sun8i-r16-nintendo-super-nes-classic.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: GPL-2.0 OR X11 +/* Copyright (c) 2018 Miquèl RAYNAL <miquel.raynal@bootlin.com> */ + +/dts-v1/; +#include "sun8i-r16-nintendo-nes-classic.dts" + +/ { + model = "Nintendo SuperNES Classic Edition"; + compatible = "nintendo,super-nes-classic", "nintendo,nes-classic", + "allwinner,sun8i-r16", "allwinner,sun8i-a33"; +}; diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts index 27d9ccd0ef2f..25fb048c7df2 100644 --- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts +++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts @@ -51,6 +51,7 @@ compatible = "sinovoip,bpi-m2-ultra", "allwinner,sun8i-r40"; aliases { + ethernet0 = &gmac; serial0 = &uart0; }; @@ -101,6 +102,22 @@ status = "okay"; }; +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_rgmii_pins>; + phy-handle = <&phy1>; + phy-mode = "rgmii"; + phy-supply = <®_dc1sw>; + status = "okay"; +}; + +&gmac_mdio { + phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &i2c0 { status = "okay"; @@ -114,6 +131,48 @@ #include "axp22x.dtsi" +&mmc0 { + vmmc-supply = <®_dcdc1>; + bus-width = <4>; + cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */ + cd-inverted; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pg_pins>; + vmmc-supply = <®_dldo2>; + vqmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&mmc2 { + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-pa"; +}; + ®_aldo3 { regulator-always-on; regulator-min-microvolt = <2700000>; @@ -121,6 +180,12 @@ regulator-name = "avcc"; }; +®_dc1sw { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-gmac-phy"; +}; + ®_dcdc1 { regulator-always-on; regulator-min-microvolt = <3000000>; @@ -161,40 +226,6 @@ regulator-name = "vcc-wifi"; }; -&mmc0 { - vmmc-supply = <®_dcdc1>; - bus-width = <4>; - cd-gpios = <&pio 7 13 GPIO_ACTIVE_LOW>; /* PH13 */ - status = "okay"; -}; - -&mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pg_pins>; - vmmc-supply = <®_dldo2>; - vqmmc-supply = <®_dldo1>; - mmc-pwrseq = <&wifi_pwrseq>; - bus-width = <4>; - non-removable; - status = "okay"; -}; - -&mmc2 { - vmmc-supply = <®_dcdc1>; - vqmmc-supply = <®_dcdc1>; - bus-width = <8>; - non-removable; - status = "okay"; -}; - -&ohci1 { - status = "okay"; -}; - -&ohci2 { - status = "okay"; -}; - &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pb_pins>; diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi index 173dcc1652d2..bd97ca3dc2fa 100644 --- a/arch/arm/boot/dts/sun8i-r40.dtsi +++ b/arch/arm/boot/dts/sun8i-r40.dtsi @@ -265,6 +265,19 @@ #interrupt-cells = <3>; #gpio-cells = <3>; + gmac_rgmii_pins: gmac-rgmii-pins { + pins = "PA0", "PA1", "PA2", "PA3", + "PA4", "PA5", "PA6", "PA7", + "PA8", "PA10", "PA11", "PA12", + "PA13", "PA15", "PA16"; + function = "gmac"; + /* + * data lines in RGMII mode use DDR mode + * and need a higher signal drive strength + */ + drive-strength = <40>; + }; + i2c0_pins: i2c0-pins { pins = "PB0", "PB1"; function = "i2c0"; @@ -451,6 +464,27 @@ #size-cells = <0>; }; + gmac: ethernet@1c50000 { + compatible = "allwinner,sun8i-r40-gmac"; + syscon = <&ccu>; + reg = <0x01c50000 0x10000>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_GMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_GMAC>; + clock-names = "stmmaceth"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + gmac_mdio: mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + gic: interrupt-controller@1c81000 { compatible = "arm,gic-400"; reg = <0x01c81000 0x1000>, diff --git a/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dts b/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dts index d1311098ea45..ad173605b1b8 100644 --- a/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dts +++ b/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dts @@ -51,7 +51,7 @@ leds { /* The LEDs use PG0~2 pins, which conflict with MMC1 */ - status = "disbaled"; + status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts index a26d72c3f9b5..35859d8f3267 100644 --- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts +++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts @@ -87,6 +87,11 @@ }; }; +&ehci1 { + /* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */ + status = "okay"; +}; + &i2c0 { status = "okay"; @@ -170,3 +175,8 @@ pinctrl-0 = <&uart0_pb_pins>; status = "okay"; }; + +&usbphy { + usb1_vbus-supply = <®_vcc5v0>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi index 1be1a02d6df2..c3bff1105e5d 100644 --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi @@ -822,6 +822,19 @@ status = "disabled"; }; + r_i2c: i2c@1f02400 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01f02400 0x400>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&r_i2c_pins>; + clocks = <&r_ccu CLK_APB0_I2C>; + resets = <&r_ccu RST_APB0_I2C>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + r_pio: pinctrl@1f02c00 { compatible = "allwinner,sun8i-h3-r-pinctrl"; reg = <0x01f02c00 0x400>; @@ -837,6 +850,11 @@ pins = "PL11"; function = "s_cir_rx"; }; + + r_i2c_pins: r-i2c { + pins = "PL0", "PL1"; + function = "s_i2c"; + }; }; }; }; diff --git a/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi b/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi new file mode 100644 index 000000000000..f7ffdd6658a2 --- /dev/null +++ b/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi @@ -0,0 +1,215 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org> + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + aliases { + ethernet0 = &emac; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + pwr_led { + label = "librecomputer:green:pwr"; + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ + default-state = "on"; + }; + + status_led { + label = "librecomputer:blue:status"; + gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */ + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + power { + label = "power"; + linux,code = <KEY_POWER>; + gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ + }; + }; + + reg_vcc1v2: vcc1v2 { + compatible = "regulator-fixed"; + regulator-name = "vcc1v2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <®_vcc5v0>; + gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ + enable-active-high; + }; + + reg_vcc3v3: vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <®_vcc5v0>; + }; + + /* This represents the board's 5V input */ + reg_vcc5v0: vcc5v0 { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_vcc_dram: vcc-dram { + compatible = "regulator-fixed"; + regulator-name = "vcc-dram"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <®_vcc5v0>; + gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */ + enable-active-high; + }; + + reg_vcc_io: vcc-io { + compatible = "regulator-fixed"; + regulator-name = "vcc-io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <®_vcc3v3>; + gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */ + }; + + reg_vdd_cpux: vdd-cpux { + compatible = "regulator-fixed"; + regulator-name = "vdd-cpux"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <®_vcc5v0>; + gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ + enable-active-high; + }; +}; + +&codec { + allwinner,audio-routing = + "Line Out", "LINEOUT", + "MIC1", "Mic", + "Mic", "MBIAS"; + status = "okay"; +}; + +&cpu0 { + cpu-supply = <®_vdd_cpux>; +}; + +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&ehci3 { + status = "okay"; +}; + +&emac { + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&ir { + pinctrl-names = "default"; + pinctrl-0 = <&ir_pins_a>; + status = "okay"; +}; + +&mmc0 { + vmmc-supply = <®_vcc_io>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&ohci3 { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + /* VBUS on USB ports are always on */ + usb0_vbus-supply = <®_vcc5v0>; + usb1_vbus-supply = <®_vcc5v0>; + usb2_vbus-supply = <®_vcc5v0>; + usb3_vbus-supply = <®_vcc5v0>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/tegra114.dtsi b/arch/arm/boot/dts/tegra114.dtsi index 0e4a13295d8a..84c4358dacac 100644 --- a/arch/arm/boot/dts/tegra114.dtsi +++ b/arch/arm/boot/dts/tegra114.dtsi @@ -19,6 +19,7 @@ clocks = <&tegra_car TEGRA114_CLK_HOST1X>; resets = <&tegra_car 28>; reset-names = "host1x"; + iommus = <&mc TEGRA_SWGROUP_HC>; #address-cells = <1>; #size-cells = <1>; @@ -32,6 +33,8 @@ clocks = <&tegra_car TEGRA114_CLK_GR2D>; resets = <&tegra_car 21>; reset-names = "2d"; + + iommus = <&mc TEGRA_SWGROUP_G2>; }; gr3d@54180000 { @@ -40,6 +43,8 @@ clocks = <&tegra_car TEGRA114_CLK_GR3D>; resets = <&tegra_car 24>; reset-names = "3d"; + + iommus = <&mc TEGRA_SWGROUP_NV>; }; dc@54200000 { diff --git a/arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi b/arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi index bb67edb016c5..3455822350c5 100644 --- a/arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi +++ b/arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi @@ -1536,15 +1536,15 @@ }; serial@70006040 { - compatible = "nvidia,tegra124-hsuart"; + compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart"; }; serial@70006200 { - compatible = "nvidia,tegra124-hsuart"; + compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart"; }; serial@70006300 { - compatible = "nvidia,tegra124-hsuart"; + compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart"; }; hdmi_ddc: i2c@7000c700 { diff --git a/arch/arm/boot/dts/tegra124-apalis.dtsi b/arch/arm/boot/dts/tegra124-apalis.dtsi index 65a2161b9b8e..9f960c84ba10 100644 --- a/arch/arm/boot/dts/tegra124-apalis.dtsi +++ b/arch/arm/boot/dts/tegra124-apalis.dtsi @@ -1565,15 +1565,15 @@ }; serial@70006040 { - compatible = "nvidia,tegra124-hsuart"; + compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart"; }; serial@70006200 { - compatible = "nvidia,tegra124-hsuart"; + compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart"; }; serial@70006300 { - compatible = "nvidia,tegra124-hsuart"; + compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart"; }; hdmi_ddc: i2c@7000c400 { diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi index 0a7136462a1a..983dd5c14794 100644 --- a/arch/arm/boot/dts/tegra20.dtsi +++ b/arch/arm/boot/dts/tegra20.dtsi @@ -741,7 +741,7 @@ phy_type = "ulpi"; clocks = <&tegra_car TEGRA20_CLK_USB2>, <&tegra_car TEGRA20_CLK_PLL_U>, - <&tegra_car TEGRA20_CLK_PLL_P_OUT4>; + <&tegra_car TEGRA20_CLK_CDEV2>; clock-names = "reg", "pll_u", "ulpi-link"; resets = <&tegra_car 58>, <&tegra_car 22>; reset-names = "usb", "utmi-pads"; diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi index a110cf84d85f..09087b9c5e26 100644 --- a/arch/arm/boot/dts/tegra30.dtsi +++ b/arch/arm/boot/dts/tegra30.dtsi @@ -112,6 +112,7 @@ clocks = <&tegra_car TEGRA30_CLK_HOST1X>; resets = <&tegra_car 28>; reset-names = "host1x"; + iommus = <&mc TEGRA_SWGROUP_HC>; #address-cells = <1>; #size-cells = <1>; @@ -125,6 +126,8 @@ clocks = <&tegra_car TEGRA30_CLK_MPE>; resets = <&tegra_car 60>; reset-names = "mpe"; + + iommus = <&mc TEGRA_SWGROUP_MPE>; }; vi@54080000 { @@ -134,6 +137,8 @@ clocks = <&tegra_car TEGRA30_CLK_VI>; resets = <&tegra_car 20>; reset-names = "vi"; + + iommus = <&mc TEGRA_SWGROUP_VI>; }; epp@540c0000 { @@ -143,6 +148,8 @@ clocks = <&tegra_car TEGRA30_CLK_EPP>; resets = <&tegra_car 19>; reset-names = "epp"; + + iommus = <&mc TEGRA_SWGROUP_EPP>; }; isp@54100000 { @@ -152,6 +159,8 @@ clocks = <&tegra_car TEGRA30_CLK_ISP>; resets = <&tegra_car 23>; reset-names = "isp"; + + iommus = <&mc TEGRA_SWGROUP_ISP>; }; gr2d@54140000 { @@ -161,6 +170,8 @@ clocks = <&tegra_car TEGRA30_CLK_GR2D>; resets = <&tegra_car 21>; reset-names = "2d"; + + iommus = <&mc TEGRA_SWGROUP_G2>; }; gr3d@54180000 { @@ -172,6 +183,9 @@ resets = <&tegra_car 24>, <&tegra_car 98>; reset-names = "3d", "3d2"; + + iommus = <&mc TEGRA_SWGROUP_NV>, + <&mc TEGRA_SWGROUP_NV2>; }; dc@54200000 { diff --git a/arch/arm/boot/dts/uniphier-pro4.dtsi b/arch/arm/boot/dts/uniphier-pro4.dtsi index 844124bc9c9c..49539f035219 100644 --- a/arch/arm/boot/dts/uniphier-pro4.dtsi +++ b/arch/arm/boot/dts/uniphier-pro4.dtsi @@ -286,7 +286,7 @@ has-transaction-translator; }; - soc-glue@5f800000 { + soc_glue: soc-glue@5f800000 { compatible = "socionext,uniphier-pro4-soc-glue", "simple-mfd", "syscon"; reg = <0x5f800000 0x2000>; @@ -371,10 +371,14 @@ interrupts = <0 66 4>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ether_rgmii>; - clocks = <&sys_clk 6>; - resets = <&sys_rst 6>; + clock-names = "gio", "ether", "ether-gb", "ether-phy"; + clocks = <&sys_clk 12>, <&sys_clk 6>, <&sys_clk 7>, + <&sys_clk 10>; + reset-names = "gio", "ether"; + resets = <&sys_rst 12>, <&sys_rst 6>; phy-mode = "rgmii"; local-mac-address = [00 00 00 00 00 00]; + socionext,syscon-phy-mode = <&soc_glue 0>; mdio: mdio { #address-cells = <1>; diff --git a/arch/arm/boot/dts/uniphier-pxs2.dtsi b/arch/arm/boot/dts/uniphier-pxs2.dtsi index debcbd15c24b..641d96119d4f 100644 --- a/arch/arm/boot/dts/uniphier-pxs2.dtsi +++ b/arch/arm/boot/dts/uniphier-pxs2.dtsi @@ -506,10 +506,13 @@ interrupts = <0 66 4>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ether_rgmii>; + clock-names = "ether"; clocks = <&sys_clk 6>; + reset-names = "ether"; resets = <&sys_rst 6>; phy-mode = "rgmii"; local-mac-address = [00 00 00 00 00 00]; + socionext,syscon-phy-mode = <&soc_glue 0>; mdio: mdio { #address-cells = <1>; diff --git a/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi b/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi index 35714ff6f467..4488c8fe213a 100644 --- a/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi +++ b/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi @@ -17,426 +17,436 @@ * CHANGES TO vexpress-v2m.dtsi! */ - motherboard { - model = "V2M-P1"; - arm,hbi = <0x190>; - arm,vexpress,site = <0>; - arm,v2m-memory-map = "rs1"; - compatible = "arm,vexpress,v2m-p1", "simple-bus"; - #address-cells = <2>; /* SMB chipselect number and offset */ - #size-cells = <1>; - #interrupt-cells = <1>; - ranges; - - flash@0,00000000 { - compatible = "arm,vexpress-flash", "cfi-flash"; - reg = <0 0x00000000 0x04000000>, - <4 0x00000000 0x04000000>; - bank-width = <4>; - }; +/ { + smb@8000000 { + motherboard { + model = "V2M-P1"; + arm,hbi = <0x190>; + arm,vexpress,site = <0>; + arm,v2m-memory-map = "rs1"; + compatible = "arm,vexpress,v2m-p1", "simple-bus"; + #address-cells = <2>; /* SMB chipselect number and offset */ + #size-cells = <1>; + #interrupt-cells = <1>; + ranges; - psram@1,00000000 { - compatible = "arm,vexpress-psram", "mtd-ram"; - reg = <1 0x00000000 0x02000000>; - bank-width = <4>; - }; + flash@0,00000000 { + compatible = "arm,vexpress-flash", "cfi-flash"; + reg = <0 0x00000000 0x04000000>, + <4 0x00000000 0x04000000>; + bank-width = <4>; + }; - v2m_video_ram: vram@2,00000000 { - compatible = "arm,vexpress-vram"; - reg = <2 0x00000000 0x00800000>; - }; + psram@1,00000000 { + compatible = "arm,vexpress-psram", "mtd-ram"; + reg = <1 0x00000000 0x02000000>; + bank-width = <4>; + }; - ethernet@2,02000000 { - compatible = "smsc,lan9118", "smsc,lan9115"; - reg = <2 0x02000000 0x10000>; - interrupts = <15>; - phy-mode = "mii"; - reg-io-width = <4>; - smsc,irq-active-high; - smsc,irq-push-pull; - vdd33a-supply = <&v2m_fixed_3v3>; - vddvario-supply = <&v2m_fixed_3v3>; - }; + v2m_video_ram: vram@2,00000000 { + compatible = "arm,vexpress-vram"; + reg = <2 0x00000000 0x00800000>; + }; - usb@2,03000000 { - compatible = "nxp,usb-isp1761"; - reg = <2 0x03000000 0x20000>; - interrupts = <16>; - port1-otg; - }; + ethernet@2,02000000 { + compatible = "smsc,lan9118", "smsc,lan9115"; + reg = <2 0x02000000 0x10000>; + interrupts = <15>; + phy-mode = "mii"; + reg-io-width = <4>; + smsc,irq-active-high; + smsc,irq-push-pull; + vdd33a-supply = <&v2m_fixed_3v3>; + vddvario-supply = <&v2m_fixed_3v3>; + }; - iofpga@3,00000000 { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 3 0 0x200000>; + usb@2,03000000 { + compatible = "nxp,usb-isp1761"; + reg = <2 0x03000000 0x20000>; + interrupts = <16>; + port1-otg; + }; - v2m_sysreg: sysreg@10000 { - compatible = "arm,vexpress-sysreg"; - reg = <0x010000 0x1000>; + iofpga@3,00000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 3 0 0x200000>; + + v2m_sysreg: sysreg@10000 { + compatible = "arm,vexpress-sysreg"; + reg = <0x010000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x10000 0x1000>; + + v2m_led_gpios: gpio@8 { + compatible = "arm,vexpress-sysreg,sys_led"; + reg = <0x008 4>; + gpio-controller; + #gpio-cells = <2>; + }; - v2m_led_gpios: sys_led { - compatible = "arm,vexpress-sysreg,sys_led"; - gpio-controller; - #gpio-cells = <2>; - }; + v2m_mmc_gpios: gpio@48 { + compatible = "arm,vexpress-sysreg,sys_mci"; + reg = <0x048 4>; + gpio-controller; + #gpio-cells = <2>; + }; - v2m_mmc_gpios: sys_mci { - compatible = "arm,vexpress-sysreg,sys_mci"; - gpio-controller; - #gpio-cells = <2>; + v2m_flash_gpios: gpio@4c { + compatible = "arm,vexpress-sysreg,sys_flash"; + reg = <0x04c 4>; + gpio-controller; + #gpio-cells = <2>; + }; }; - v2m_flash_gpios: sys_flash { - compatible = "arm,vexpress-sysreg,sys_flash"; - gpio-controller; - #gpio-cells = <2>; + v2m_sysctl: sysctl@20000 { + compatible = "arm,sp810", "arm,primecell"; + reg = <0x020000 0x1000>; + clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>; + clock-names = "refclk", "timclk", "apb_pclk"; + #clock-cells = <1>; + clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3"; + assigned-clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&v2m_sysctl 3>, <&v2m_sysctl 3>; + assigned-clock-parents = <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>; }; - }; - v2m_sysctl: sysctl@20000 { - compatible = "arm,sp810", "arm,primecell"; - reg = <0x020000 0x1000>; - clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>; - clock-names = "refclk", "timclk", "apb_pclk"; - #clock-cells = <1>; - clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3"; - assigned-clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&v2m_sysctl 3>, <&v2m_sysctl 3>; - assigned-clock-parents = <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>; - }; + /* PCI-E I2C bus */ + v2m_i2c_pcie: i2c@30000 { + compatible = "arm,versatile-i2c"; + reg = <0x030000 0x1000>; - /* PCI-E I2C bus */ - v2m_i2c_pcie: i2c@30000 { - compatible = "arm,versatile-i2c"; - reg = <0x030000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; - #address-cells = <1>; - #size-cells = <0>; + pcie-switch@60 { + compatible = "idt,89hpes32h8"; + reg = <0x60>; + }; + }; - pcie-switch@60 { - compatible = "idt,89hpes32h8"; - reg = <0x60>; + aaci@40000 { + compatible = "arm,pl041", "arm,primecell"; + reg = <0x040000 0x1000>; + interrupts = <11>; + clocks = <&smbclk>; + clock-names = "apb_pclk"; }; - }; - aaci@40000 { - compatible = "arm,pl041", "arm,primecell"; - reg = <0x040000 0x1000>; - interrupts = <11>; - clocks = <&smbclk>; - clock-names = "apb_pclk"; - }; + mmci@50000 { + compatible = "arm,pl180", "arm,primecell"; + reg = <0x050000 0x1000>; + interrupts = <9 10>; + cd-gpios = <&v2m_mmc_gpios 0 0>; + wp-gpios = <&v2m_mmc_gpios 1 0>; + max-frequency = <12000000>; + vmmc-supply = <&v2m_fixed_3v3>; + clocks = <&v2m_clk24mhz>, <&smbclk>; + clock-names = "mclk", "apb_pclk"; + }; - mmci@50000 { - compatible = "arm,pl180", "arm,primecell"; - reg = <0x050000 0x1000>; - interrupts = <9 10>; - cd-gpios = <&v2m_mmc_gpios 0 0>; - wp-gpios = <&v2m_mmc_gpios 1 0>; - max-frequency = <12000000>; - vmmc-supply = <&v2m_fixed_3v3>; - clocks = <&v2m_clk24mhz>, <&smbclk>; - clock-names = "mclk", "apb_pclk"; - }; + kmi@60000 { + compatible = "arm,pl050", "arm,primecell"; + reg = <0x060000 0x1000>; + interrupts = <12>; + clocks = <&v2m_clk24mhz>, <&smbclk>; + clock-names = "KMIREFCLK", "apb_pclk"; + }; - kmi@60000 { - compatible = "arm,pl050", "arm,primecell"; - reg = <0x060000 0x1000>; - interrupts = <12>; - clocks = <&v2m_clk24mhz>, <&smbclk>; - clock-names = "KMIREFCLK", "apb_pclk"; - }; + kmi@70000 { + compatible = "arm,pl050", "arm,primecell"; + reg = <0x070000 0x1000>; + interrupts = <13>; + clocks = <&v2m_clk24mhz>, <&smbclk>; + clock-names = "KMIREFCLK", "apb_pclk"; + }; - kmi@70000 { - compatible = "arm,pl050", "arm,primecell"; - reg = <0x070000 0x1000>; - interrupts = <13>; - clocks = <&v2m_clk24mhz>, <&smbclk>; - clock-names = "KMIREFCLK", "apb_pclk"; - }; + v2m_serial0: uart@90000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x090000 0x1000>; + interrupts = <5>; + clocks = <&v2m_oscclk2>, <&smbclk>; + clock-names = "uartclk", "apb_pclk"; + }; - v2m_serial0: uart@90000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x090000 0x1000>; - interrupts = <5>; - clocks = <&v2m_oscclk2>, <&smbclk>; - clock-names = "uartclk", "apb_pclk"; - }; + v2m_serial1: uart@a0000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0a0000 0x1000>; + interrupts = <6>; + clocks = <&v2m_oscclk2>, <&smbclk>; + clock-names = "uartclk", "apb_pclk"; + }; - v2m_serial1: uart@a0000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x0a0000 0x1000>; - interrupts = <6>; - clocks = <&v2m_oscclk2>, <&smbclk>; - clock-names = "uartclk", "apb_pclk"; - }; + v2m_serial2: uart@b0000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0b0000 0x1000>; + interrupts = <7>; + clocks = <&v2m_oscclk2>, <&smbclk>; + clock-names = "uartclk", "apb_pclk"; + }; - v2m_serial2: uart@b0000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x0b0000 0x1000>; - interrupts = <7>; - clocks = <&v2m_oscclk2>, <&smbclk>; - clock-names = "uartclk", "apb_pclk"; - }; + v2m_serial3: uart@c0000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0c0000 0x1000>; + interrupts = <8>; + clocks = <&v2m_oscclk2>, <&smbclk>; + clock-names = "uartclk", "apb_pclk"; + }; - v2m_serial3: uart@c0000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x0c0000 0x1000>; - interrupts = <8>; - clocks = <&v2m_oscclk2>, <&smbclk>; - clock-names = "uartclk", "apb_pclk"; - }; + wdt@f0000 { + compatible = "arm,sp805", "arm,primecell"; + reg = <0x0f0000 0x1000>; + interrupts = <0>; + clocks = <&v2m_refclk32khz>, <&smbclk>; + clock-names = "wdogclk", "apb_pclk"; + }; - wdt@f0000 { - compatible = "arm,sp805", "arm,primecell"; - reg = <0x0f0000 0x1000>; - interrupts = <0>; - clocks = <&v2m_refclk32khz>, <&smbclk>; - clock-names = "wdogclk", "apb_pclk"; - }; + v2m_timer01: timer@110000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x110000 0x1000>; + interrupts = <2>; + clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>; + clock-names = "timclken1", "timclken2", "apb_pclk"; + }; - v2m_timer01: timer@110000 { - compatible = "arm,sp804", "arm,primecell"; - reg = <0x110000 0x1000>; - interrupts = <2>; - clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>; - clock-names = "timclken1", "timclken2", "apb_pclk"; - }; + v2m_timer23: timer@120000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x120000 0x1000>; + interrupts = <3>; + clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&smbclk>; + clock-names = "timclken1", "timclken2", "apb_pclk"; + }; - v2m_timer23: timer@120000 { - compatible = "arm,sp804", "arm,primecell"; - reg = <0x120000 0x1000>; - interrupts = <3>; - clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&smbclk>; - clock-names = "timclken1", "timclken2", "apb_pclk"; - }; + /* DVI I2C bus */ + v2m_i2c_dvi: i2c@160000 { + compatible = "arm,versatile-i2c"; + reg = <0x160000 0x1000>; - /* DVI I2C bus */ - v2m_i2c_dvi: i2c@160000 { - compatible = "arm,versatile-i2c"; - reg = <0x160000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; - #address-cells = <1>; - #size-cells = <0>; + dvi-transmitter@39 { + compatible = "sil,sii9022-tpi", "sil,sii9022"; + reg = <0x39>; + }; - dvi-transmitter@39 { - compatible = "sil,sii9022-tpi", "sil,sii9022"; - reg = <0x39>; + dvi-transmitter@60 { + compatible = "sil,sii9022-cpi", "sil,sii9022"; + reg = <0x60>; + }; }; - dvi-transmitter@60 { - compatible = "sil,sii9022-cpi", "sil,sii9022"; - reg = <0x60>; + rtc@170000 { + compatible = "arm,pl031", "arm,primecell"; + reg = <0x170000 0x1000>; + interrupts = <4>; + clocks = <&smbclk>; + clock-names = "apb_pclk"; }; - }; - rtc@170000 { - compatible = "arm,pl031", "arm,primecell"; - reg = <0x170000 0x1000>; - interrupts = <4>; - clocks = <&smbclk>; - clock-names = "apb_pclk"; - }; - - compact-flash@1a0000 { - compatible = "arm,vexpress-cf", "ata-generic"; - reg = <0x1a0000 0x100 - 0x1a0100 0xf00>; - reg-shift = <2>; - }; - - clcd@1f0000 { - compatible = "arm,pl111", "arm,primecell"; - reg = <0x1f0000 0x1000>; - interrupt-names = "combined"; - interrupts = <14>; - clocks = <&v2m_oscclk1>, <&smbclk>; - clock-names = "clcdclk", "apb_pclk"; - memory-region = <&v2m_video_ram>; - max-memory-bandwidth = <50350000>; /* 16bpp @ 25.175MHz */ - - port { - v2m_clcd_pads: endpoint { - remote-endpoint = <&v2m_clcd_panel>; - arm,pl11x,tft-r0g0b0-pads = <0 8 16>; - }; + compact-flash@1a0000 { + compatible = "arm,vexpress-cf", "ata-generic"; + reg = <0x1a0000 0x100 + 0x1a0100 0xf00>; + reg-shift = <2>; }; - panel { - compatible = "panel-dpi"; + clcd@1f0000 { + compatible = "arm,pl111", "arm,primecell"; + reg = <0x1f0000 0x1000>; + interrupt-names = "combined"; + interrupts = <14>; + clocks = <&v2m_oscclk1>, <&smbclk>; + clock-names = "clcdclk", "apb_pclk"; + memory-region = <&v2m_video_ram>; + max-memory-bandwidth = <50350000>; /* 16bpp @ 25.175MHz */ port { - v2m_clcd_panel: endpoint { - remote-endpoint = <&v2m_clcd_pads>; + v2m_clcd_pads: endpoint { + remote-endpoint = <&v2m_clcd_panel>; + arm,pl11x,tft-r0g0b0-pads = <0 8 16>; }; }; - panel-timing { - clock-frequency = <25175000>; - hactive = <640>; - hback-porch = <40>; - hfront-porch = <24>; - hsync-len = <96>; - vactive = <480>; - vback-porch = <32>; - vfront-porch = <11>; - vsync-len = <2>; + panel { + compatible = "panel-dpi"; + + port { + v2m_clcd_panel: endpoint { + remote-endpoint = <&v2m_clcd_pads>; + }; + }; + + panel-timing { + clock-frequency = <25175000>; + hactive = <640>; + hback-porch = <40>; + hfront-porch = <24>; + hsync-len = <96>; + vactive = <480>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <2>; + }; }; }; }; - }; - v2m_fixed_3v3: fixed-regulator-0 { - compatible = "regulator-fixed"; - regulator-name = "3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; + v2m_fixed_3v3: fixed-regulator-0 { + compatible = "regulator-fixed"; + regulator-name = "3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; - v2m_clk24mhz: clk24mhz { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <24000000>; - clock-output-names = "v2m:clk24mhz"; - }; + v2m_clk24mhz: clk24mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + clock-output-names = "v2m:clk24mhz"; + }; - v2m_refclk1mhz: refclk1mhz { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <1000000>; - clock-output-names = "v2m:refclk1mhz"; - }; + v2m_refclk1mhz: refclk1mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <1000000>; + clock-output-names = "v2m:refclk1mhz"; + }; - v2m_refclk32khz: refclk32khz { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <32768>; - clock-output-names = "v2m:refclk32khz"; - }; + v2m_refclk32khz: refclk32khz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "v2m:refclk32khz"; + }; - leds { - compatible = "gpio-leds"; + leds { + compatible = "gpio-leds"; - user1 { - label = "v2m:green:user1"; - gpios = <&v2m_led_gpios 0 0>; - linux,default-trigger = "heartbeat"; - }; + user1 { + label = "v2m:green:user1"; + gpios = <&v2m_led_gpios 0 0>; + linux,default-trigger = "heartbeat"; + }; - user2 { - label = "v2m:green:user2"; - gpios = <&v2m_led_gpios 1 0>; - linux,default-trigger = "mmc0"; - }; + user2 { + label = "v2m:green:user2"; + gpios = <&v2m_led_gpios 1 0>; + linux,default-trigger = "mmc0"; + }; - user3 { - label = "v2m:green:user3"; - gpios = <&v2m_led_gpios 2 0>; - linux,default-trigger = "cpu0"; - }; + user3 { + label = "v2m:green:user3"; + gpios = <&v2m_led_gpios 2 0>; + linux,default-trigger = "cpu0"; + }; - user4 { - label = "v2m:green:user4"; - gpios = <&v2m_led_gpios 3 0>; - linux,default-trigger = "cpu1"; - }; + user4 { + label = "v2m:green:user4"; + gpios = <&v2m_led_gpios 3 0>; + linux,default-trigger = "cpu1"; + }; - user5 { - label = "v2m:green:user5"; - gpios = <&v2m_led_gpios 4 0>; - linux,default-trigger = "cpu2"; - }; + user5 { + label = "v2m:green:user5"; + gpios = <&v2m_led_gpios 4 0>; + linux,default-trigger = "cpu2"; + }; - user6 { - label = "v2m:green:user6"; - gpios = <&v2m_led_gpios 5 0>; - linux,default-trigger = "cpu3"; - }; + user6 { + label = "v2m:green:user6"; + gpios = <&v2m_led_gpios 5 0>; + linux,default-trigger = "cpu3"; + }; - user7 { - label = "v2m:green:user7"; - gpios = <&v2m_led_gpios 6 0>; - linux,default-trigger = "cpu4"; - }; + user7 { + label = "v2m:green:user7"; + gpios = <&v2m_led_gpios 6 0>; + linux,default-trigger = "cpu4"; + }; - user8 { - label = "v2m:green:user8"; - gpios = <&v2m_led_gpios 7 0>; - linux,default-trigger = "cpu5"; + user8 { + label = "v2m:green:user8"; + gpios = <&v2m_led_gpios 7 0>; + linux,default-trigger = "cpu5"; + }; }; - }; - mcc { - compatible = "arm,vexpress,config-bus"; - arm,vexpress,config-bridge = <&v2m_sysreg>; + mcc { + compatible = "arm,vexpress,config-bus"; + arm,vexpress,config-bridge = <&v2m_sysreg>; - oscclk0 { - /* MCC static memory clock */ - compatible = "arm,vexpress-osc"; - arm,vexpress-sysreg,func = <1 0>; - freq-range = <25000000 60000000>; - #clock-cells = <0>; - clock-output-names = "v2m:oscclk0"; - }; + oscclk0 { + /* MCC static memory clock */ + compatible = "arm,vexpress-osc"; + arm,vexpress-sysreg,func = <1 0>; + freq-range = <25000000 60000000>; + #clock-cells = <0>; + clock-output-names = "v2m:oscclk0"; + }; - v2m_oscclk1: oscclk1 { - /* CLCD clock */ - compatible = "arm,vexpress-osc"; - arm,vexpress-sysreg,func = <1 1>; - freq-range = <23750000 65000000>; - #clock-cells = <0>; - clock-output-names = "v2m:oscclk1"; - }; + v2m_oscclk1: oscclk1 { + /* CLCD clock */ + compatible = "arm,vexpress-osc"; + arm,vexpress-sysreg,func = <1 1>; + freq-range = <23750000 65000000>; + #clock-cells = <0>; + clock-output-names = "v2m:oscclk1"; + }; - v2m_oscclk2: oscclk2 { - /* IO FPGA peripheral clock */ - compatible = "arm,vexpress-osc"; - arm,vexpress-sysreg,func = <1 2>; - freq-range = <24000000 24000000>; - #clock-cells = <0>; - clock-output-names = "v2m:oscclk2"; - }; + v2m_oscclk2: oscclk2 { + /* IO FPGA peripheral clock */ + compatible = "arm,vexpress-osc"; + arm,vexpress-sysreg,func = <1 2>; + freq-range = <24000000 24000000>; + #clock-cells = <0>; + clock-output-names = "v2m:oscclk2"; + }; - volt-vio { - /* Logic level voltage */ - compatible = "arm,vexpress-volt"; - arm,vexpress-sysreg,func = <2 0>; - regulator-name = "VIO"; - regulator-always-on; - label = "VIO"; - }; + volt-vio { + /* Logic level voltage */ + compatible = "arm,vexpress-volt"; + arm,vexpress-sysreg,func = <2 0>; + regulator-name = "VIO"; + regulator-always-on; + label = "VIO"; + }; - temp-mcc { - /* MCC internal operating temperature */ - compatible = "arm,vexpress-temp"; - arm,vexpress-sysreg,func = <4 0>; - label = "MCC"; - }; + temp-mcc { + /* MCC internal operating temperature */ + compatible = "arm,vexpress-temp"; + arm,vexpress-sysreg,func = <4 0>; + label = "MCC"; + }; - reset { - compatible = "arm,vexpress-reset"; - arm,vexpress-sysreg,func = <5 0>; - }; + reset { + compatible = "arm,vexpress-reset"; + arm,vexpress-sysreg,func = <5 0>; + }; - muxfpga { - compatible = "arm,vexpress-muxfpga"; - arm,vexpress-sysreg,func = <7 0>; - }; + muxfpga { + compatible = "arm,vexpress-muxfpga"; + arm,vexpress-sysreg,func = <7 0>; + }; - shutdown { - compatible = "arm,vexpress-shutdown"; - arm,vexpress-sysreg,func = <8 0>; - }; + shutdown { + compatible = "arm,vexpress-shutdown"; + arm,vexpress-sysreg,func = <8 0>; + }; - reboot { - compatible = "arm,vexpress-reboot"; - arm,vexpress-sysreg,func = <9 0>; - }; + reboot { + compatible = "arm,vexpress-reboot"; + arm,vexpress-sysreg,func = <9 0>; + }; - dvimode { - compatible = "arm,vexpress-dvimode"; - arm,vexpress-sysreg,func = <11 0>; + dvimode { + compatible = "arm,vexpress-dvimode"; + arm,vexpress-sysreg,func = <11 0>; + }; }; }; }; +}; diff --git a/arch/arm/boot/dts/vexpress-v2m.dtsi b/arch/arm/boot/dts/vexpress-v2m.dtsi index b0021a816028..4db42f6326a3 100644 --- a/arch/arm/boot/dts/vexpress-v2m.dtsi +++ b/arch/arm/boot/dts/vexpress-v2m.dtsi @@ -18,425 +18,435 @@ * CHANGES TO vexpress-v2m-rs1.dtsi! */ - motherboard { - model = "V2M-P1"; - arm,hbi = <0x190>; - arm,vexpress,site = <0>; - compatible = "arm,vexpress,v2m-p1", "simple-bus"; - #address-cells = <2>; /* SMB chipselect number and offset */ - #size-cells = <1>; - #interrupt-cells = <1>; - ranges; - - flash@0,00000000 { - compatible = "arm,vexpress-flash", "cfi-flash"; - reg = <0 0x00000000 0x04000000>, - <1 0x00000000 0x04000000>; - bank-width = <4>; - }; +/ { + smb@4000000 { + motherboard { + model = "V2M-P1"; + arm,hbi = <0x190>; + arm,vexpress,site = <0>; + compatible = "arm,vexpress,v2m-p1", "simple-bus"; + #address-cells = <2>; /* SMB chipselect number and offset */ + #size-cells = <1>; + #interrupt-cells = <1>; + ranges; - psram@2,00000000 { - compatible = "arm,vexpress-psram", "mtd-ram"; - reg = <2 0x00000000 0x02000000>; - bank-width = <4>; - }; + flash@0,00000000 { + compatible = "arm,vexpress-flash", "cfi-flash"; + reg = <0 0x00000000 0x04000000>, + <1 0x00000000 0x04000000>; + bank-width = <4>; + }; - v2m_video_ram: vram@3,00000000 { - compatible = "arm,vexpress-vram"; - reg = <3 0x00000000 0x00800000>; - }; + psram@2,00000000 { + compatible = "arm,vexpress-psram", "mtd-ram"; + reg = <2 0x00000000 0x02000000>; + bank-width = <4>; + }; - ethernet@3,02000000 { - compatible = "smsc,lan9118", "smsc,lan9115"; - reg = <3 0x02000000 0x10000>; - interrupts = <15>; - phy-mode = "mii"; - reg-io-width = <4>; - smsc,irq-active-high; - smsc,irq-push-pull; - vdd33a-supply = <&v2m_fixed_3v3>; - vddvario-supply = <&v2m_fixed_3v3>; - }; + v2m_video_ram: vram@3,00000000 { + compatible = "arm,vexpress-vram"; + reg = <3 0x00000000 0x00800000>; + }; - usb@3,03000000 { - compatible = "nxp,usb-isp1761"; - reg = <3 0x03000000 0x20000>; - interrupts = <16>; - port1-otg; - }; + ethernet@3,02000000 { + compatible = "smsc,lan9118", "smsc,lan9115"; + reg = <3 0x02000000 0x10000>; + interrupts = <15>; + phy-mode = "mii"; + reg-io-width = <4>; + smsc,irq-active-high; + smsc,irq-push-pull; + vdd33a-supply = <&v2m_fixed_3v3>; + vddvario-supply = <&v2m_fixed_3v3>; + }; - iofpga@7,00000000 { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 7 0 0x20000>; + usb@3,03000000 { + compatible = "nxp,usb-isp1761"; + reg = <3 0x03000000 0x20000>; + interrupts = <16>; + port1-otg; + }; - v2m_sysreg: sysreg@0 { - compatible = "arm,vexpress-sysreg"; - reg = <0x00000 0x1000>; + iofpga@7,00000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 7 0 0x20000>; + + v2m_sysreg: sysreg@0 { + compatible = "arm,vexpress-sysreg"; + reg = <0x00000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x1000>; + + v2m_led_gpios: gpio@8 { + compatible = "arm,vexpress-sysreg,sys_led"; + reg = <0x008 4>; + gpio-controller; + #gpio-cells = <2>; + }; - v2m_led_gpios: sys_led { - compatible = "arm,vexpress-sysreg,sys_led"; - gpio-controller; - #gpio-cells = <2>; - }; + v2m_mmc_gpios: gpio@48 { + compatible = "arm,vexpress-sysreg,sys_mci"; + reg = <0x048 4>; + gpio-controller; + #gpio-cells = <2>; + }; - v2m_mmc_gpios: sys_mci { - compatible = "arm,vexpress-sysreg,sys_mci"; - gpio-controller; - #gpio-cells = <2>; + v2m_flash_gpios: gpio@4c { + compatible = "arm,vexpress-sysreg,sys_flash"; + reg = <0x04c 4>; + gpio-controller; + #gpio-cells = <2>; + }; }; - v2m_flash_gpios: sys_flash { - compatible = "arm,vexpress-sysreg,sys_flash"; - gpio-controller; - #gpio-cells = <2>; + v2m_sysctl: sysctl@1000 { + compatible = "arm,sp810", "arm,primecell"; + reg = <0x01000 0x1000>; + clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>; + clock-names = "refclk", "timclk", "apb_pclk"; + #clock-cells = <1>; + clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3"; + assigned-clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&v2m_sysctl 3>, <&v2m_sysctl 3>; + assigned-clock-parents = <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>; }; - }; - v2m_sysctl: sysctl@1000 { - compatible = "arm,sp810", "arm,primecell"; - reg = <0x01000 0x1000>; - clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>; - clock-names = "refclk", "timclk", "apb_pclk"; - #clock-cells = <1>; - clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3"; - assigned-clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&v2m_sysctl 3>, <&v2m_sysctl 3>; - assigned-clock-parents = <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>; - }; + /* PCI-E I2C bus */ + v2m_i2c_pcie: i2c@2000 { + compatible = "arm,versatile-i2c"; + reg = <0x02000 0x1000>; - /* PCI-E I2C bus */ - v2m_i2c_pcie: i2c@2000 { - compatible = "arm,versatile-i2c"; - reg = <0x02000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; - #address-cells = <1>; - #size-cells = <0>; + pcie-switch@60 { + compatible = "idt,89hpes32h8"; + reg = <0x60>; + }; + }; - pcie-switch@60 { - compatible = "idt,89hpes32h8"; - reg = <0x60>; + aaci@4000 { + compatible = "arm,pl041", "arm,primecell"; + reg = <0x04000 0x1000>; + interrupts = <11>; + clocks = <&smbclk>; + clock-names = "apb_pclk"; }; - }; - aaci@4000 { - compatible = "arm,pl041", "arm,primecell"; - reg = <0x04000 0x1000>; - interrupts = <11>; - clocks = <&smbclk>; - clock-names = "apb_pclk"; - }; + mmci@5000 { + compatible = "arm,pl180", "arm,primecell"; + reg = <0x05000 0x1000>; + interrupts = <9 10>; + cd-gpios = <&v2m_mmc_gpios 0 0>; + wp-gpios = <&v2m_mmc_gpios 1 0>; + max-frequency = <12000000>; + vmmc-supply = <&v2m_fixed_3v3>; + clocks = <&v2m_clk24mhz>, <&smbclk>; + clock-names = "mclk", "apb_pclk"; + }; - mmci@5000 { - compatible = "arm,pl180", "arm,primecell"; - reg = <0x05000 0x1000>; - interrupts = <9 10>; - cd-gpios = <&v2m_mmc_gpios 0 0>; - wp-gpios = <&v2m_mmc_gpios 1 0>; - max-frequency = <12000000>; - vmmc-supply = <&v2m_fixed_3v3>; - clocks = <&v2m_clk24mhz>, <&smbclk>; - clock-names = "mclk", "apb_pclk"; - }; + kmi@6000 { + compatible = "arm,pl050", "arm,primecell"; + reg = <0x06000 0x1000>; + interrupts = <12>; + clocks = <&v2m_clk24mhz>, <&smbclk>; + clock-names = "KMIREFCLK", "apb_pclk"; + }; - kmi@6000 { - compatible = "arm,pl050", "arm,primecell"; - reg = <0x06000 0x1000>; - interrupts = <12>; - clocks = <&v2m_clk24mhz>, <&smbclk>; - clock-names = "KMIREFCLK", "apb_pclk"; - }; + kmi@7000 { + compatible = "arm,pl050", "arm,primecell"; + reg = <0x07000 0x1000>; + interrupts = <13>; + clocks = <&v2m_clk24mhz>, <&smbclk>; + clock-names = "KMIREFCLK", "apb_pclk"; + }; - kmi@7000 { - compatible = "arm,pl050", "arm,primecell"; - reg = <0x07000 0x1000>; - interrupts = <13>; - clocks = <&v2m_clk24mhz>, <&smbclk>; - clock-names = "KMIREFCLK", "apb_pclk"; - }; + v2m_serial0: uart@9000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x09000 0x1000>; + interrupts = <5>; + clocks = <&v2m_oscclk2>, <&smbclk>; + clock-names = "uartclk", "apb_pclk"; + }; - v2m_serial0: uart@9000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x09000 0x1000>; - interrupts = <5>; - clocks = <&v2m_oscclk2>, <&smbclk>; - clock-names = "uartclk", "apb_pclk"; - }; + v2m_serial1: uart@a000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0a000 0x1000>; + interrupts = <6>; + clocks = <&v2m_oscclk2>, <&smbclk>; + clock-names = "uartclk", "apb_pclk"; + }; - v2m_serial1: uart@a000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x0a000 0x1000>; - interrupts = <6>; - clocks = <&v2m_oscclk2>, <&smbclk>; - clock-names = "uartclk", "apb_pclk"; - }; + v2m_serial2: uart@b000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0b000 0x1000>; + interrupts = <7>; + clocks = <&v2m_oscclk2>, <&smbclk>; + clock-names = "uartclk", "apb_pclk"; + }; - v2m_serial2: uart@b000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x0b000 0x1000>; - interrupts = <7>; - clocks = <&v2m_oscclk2>, <&smbclk>; - clock-names = "uartclk", "apb_pclk"; - }; + v2m_serial3: uart@c000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0c000 0x1000>; + interrupts = <8>; + clocks = <&v2m_oscclk2>, <&smbclk>; + clock-names = "uartclk", "apb_pclk"; + }; - v2m_serial3: uart@c000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x0c000 0x1000>; - interrupts = <8>; - clocks = <&v2m_oscclk2>, <&smbclk>; - clock-names = "uartclk", "apb_pclk"; - }; + wdt@f000 { + compatible = "arm,sp805", "arm,primecell"; + reg = <0x0f000 0x1000>; + interrupts = <0>; + clocks = <&v2m_refclk32khz>, <&smbclk>; + clock-names = "wdogclk", "apb_pclk"; + }; - wdt@f000 { - compatible = "arm,sp805", "arm,primecell"; - reg = <0x0f000 0x1000>; - interrupts = <0>; - clocks = <&v2m_refclk32khz>, <&smbclk>; - clock-names = "wdogclk", "apb_pclk"; - }; + v2m_timer01: timer@11000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x11000 0x1000>; + interrupts = <2>; + clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>; + clock-names = "timclken1", "timclken2", "apb_pclk"; + }; - v2m_timer01: timer@11000 { - compatible = "arm,sp804", "arm,primecell"; - reg = <0x11000 0x1000>; - interrupts = <2>; - clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>; - clock-names = "timclken1", "timclken2", "apb_pclk"; - }; + v2m_timer23: timer@12000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x12000 0x1000>; + interrupts = <3>; + clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&smbclk>; + clock-names = "timclken1", "timclken2", "apb_pclk"; + }; - v2m_timer23: timer@12000 { - compatible = "arm,sp804", "arm,primecell"; - reg = <0x12000 0x1000>; - interrupts = <3>; - clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&smbclk>; - clock-names = "timclken1", "timclken2", "apb_pclk"; - }; + /* DVI I2C bus */ + v2m_i2c_dvi: i2c@16000 { + compatible = "arm,versatile-i2c"; + reg = <0x16000 0x1000>; - /* DVI I2C bus */ - v2m_i2c_dvi: i2c@16000 { - compatible = "arm,versatile-i2c"; - reg = <0x16000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; - #address-cells = <1>; - #size-cells = <0>; + dvi-transmitter@39 { + compatible = "sil,sii9022-tpi", "sil,sii9022"; + reg = <0x39>; + }; - dvi-transmitter@39 { - compatible = "sil,sii9022-tpi", "sil,sii9022"; - reg = <0x39>; + dvi-transmitter@60 { + compatible = "sil,sii9022-cpi", "sil,sii9022"; + reg = <0x60>; + }; }; - dvi-transmitter@60 { - compatible = "sil,sii9022-cpi", "sil,sii9022"; - reg = <0x60>; + rtc@17000 { + compatible = "arm,pl031", "arm,primecell"; + reg = <0x17000 0x1000>; + interrupts = <4>; + clocks = <&smbclk>; + clock-names = "apb_pclk"; }; - }; - rtc@17000 { - compatible = "arm,pl031", "arm,primecell"; - reg = <0x17000 0x1000>; - interrupts = <4>; - clocks = <&smbclk>; - clock-names = "apb_pclk"; - }; - - compact-flash@1a000 { - compatible = "arm,vexpress-cf", "ata-generic"; - reg = <0x1a000 0x100 - 0x1a100 0xf00>; - reg-shift = <2>; - }; - - clcd@1f000 { - compatible = "arm,pl111", "arm,primecell"; - reg = <0x1f000 0x1000>; - interrupt-names = "combined"; - interrupts = <14>; - clocks = <&v2m_oscclk1>, <&smbclk>; - clock-names = "clcdclk", "apb_pclk"; - memory-region = <&v2m_video_ram>; - max-memory-bandwidth = <50350000>; /* 16bpp @ 25.175MHz */ - - port { - v2m_clcd_pads: endpoint { - remote-endpoint = <&v2m_clcd_panel>; - arm,pl11x,tft-r0g0b0-pads = <0 8 16>; - }; + compact-flash@1a000 { + compatible = "arm,vexpress-cf", "ata-generic"; + reg = <0x1a000 0x100 + 0x1a100 0xf00>; + reg-shift = <2>; }; - panel { - compatible = "panel-dpi"; + clcd@1f000 { + compatible = "arm,pl111", "arm,primecell"; + reg = <0x1f000 0x1000>; + interrupt-names = "combined"; + interrupts = <14>; + clocks = <&v2m_oscclk1>, <&smbclk>; + clock-names = "clcdclk", "apb_pclk"; + memory-region = <&v2m_video_ram>; + max-memory-bandwidth = <50350000>; /* 16bpp @ 25.175MHz */ port { - v2m_clcd_panel: endpoint { - remote-endpoint = <&v2m_clcd_pads>; + v2m_clcd_pads: endpoint { + remote-endpoint = <&v2m_clcd_panel>; + arm,pl11x,tft-r0g0b0-pads = <0 8 16>; }; }; - panel-timing { - clock-frequency = <25175000>; - hactive = <640>; - hback-porch = <40>; - hfront-porch = <24>; - hsync-len = <96>; - vactive = <480>; - vback-porch = <32>; - vfront-porch = <11>; - vsync-len = <2>; + panel { + compatible = "panel-dpi"; + + port { + v2m_clcd_panel: endpoint { + remote-endpoint = <&v2m_clcd_pads>; + }; + }; + + panel-timing { + clock-frequency = <25175000>; + hactive = <640>; + hback-porch = <40>; + hfront-porch = <24>; + hsync-len = <96>; + vactive = <480>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <2>; + }; }; }; }; - }; - v2m_fixed_3v3: fixed-regulator-0 { - compatible = "regulator-fixed"; - regulator-name = "3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; + v2m_fixed_3v3: fixed-regulator-0 { + compatible = "regulator-fixed"; + regulator-name = "3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; - v2m_clk24mhz: clk24mhz { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <24000000>; - clock-output-names = "v2m:clk24mhz"; - }; + v2m_clk24mhz: clk24mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + clock-output-names = "v2m:clk24mhz"; + }; - v2m_refclk1mhz: refclk1mhz { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <1000000>; - clock-output-names = "v2m:refclk1mhz"; - }; + v2m_refclk1mhz: refclk1mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <1000000>; + clock-output-names = "v2m:refclk1mhz"; + }; - v2m_refclk32khz: refclk32khz { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <32768>; - clock-output-names = "v2m:refclk32khz"; - }; + v2m_refclk32khz: refclk32khz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "v2m:refclk32khz"; + }; - leds { - compatible = "gpio-leds"; + leds { + compatible = "gpio-leds"; - user1 { - label = "v2m:green:user1"; - gpios = <&v2m_led_gpios 0 0>; - linux,default-trigger = "heartbeat"; - }; + user1 { + label = "v2m:green:user1"; + gpios = <&v2m_led_gpios 0 0>; + linux,default-trigger = "heartbeat"; + }; - user2 { - label = "v2m:green:user2"; - gpios = <&v2m_led_gpios 1 0>; - linux,default-trigger = "mmc0"; - }; + user2 { + label = "v2m:green:user2"; + gpios = <&v2m_led_gpios 1 0>; + linux,default-trigger = "mmc0"; + }; - user3 { - label = "v2m:green:user3"; - gpios = <&v2m_led_gpios 2 0>; - linux,default-trigger = "cpu0"; - }; + user3 { + label = "v2m:green:user3"; + gpios = <&v2m_led_gpios 2 0>; + linux,default-trigger = "cpu0"; + }; - user4 { - label = "v2m:green:user4"; - gpios = <&v2m_led_gpios 3 0>; - linux,default-trigger = "cpu1"; - }; + user4 { + label = "v2m:green:user4"; + gpios = <&v2m_led_gpios 3 0>; + linux,default-trigger = "cpu1"; + }; - user5 { - label = "v2m:green:user5"; - gpios = <&v2m_led_gpios 4 0>; - linux,default-trigger = "cpu2"; - }; + user5 { + label = "v2m:green:user5"; + gpios = <&v2m_led_gpios 4 0>; + linux,default-trigger = "cpu2"; + }; - user6 { - label = "v2m:green:user6"; - gpios = <&v2m_led_gpios 5 0>; - linux,default-trigger = "cpu3"; - }; + user6 { + label = "v2m:green:user6"; + gpios = <&v2m_led_gpios 5 0>; + linux,default-trigger = "cpu3"; + }; - user7 { - label = "v2m:green:user7"; - gpios = <&v2m_led_gpios 6 0>; - linux,default-trigger = "cpu4"; - }; + user7 { + label = "v2m:green:user7"; + gpios = <&v2m_led_gpios 6 0>; + linux,default-trigger = "cpu4"; + }; - user8 { - label = "v2m:green:user8"; - gpios = <&v2m_led_gpios 7 0>; - linux,default-trigger = "cpu5"; + user8 { + label = "v2m:green:user8"; + gpios = <&v2m_led_gpios 7 0>; + linux,default-trigger = "cpu5"; + }; }; - }; - mcc { - compatible = "arm,vexpress,config-bus"; - arm,vexpress,config-bridge = <&v2m_sysreg>; + mcc { + compatible = "arm,vexpress,config-bus"; + arm,vexpress,config-bridge = <&v2m_sysreg>; - oscclk0 { - /* MCC static memory clock */ - compatible = "arm,vexpress-osc"; - arm,vexpress-sysreg,func = <1 0>; - freq-range = <25000000 60000000>; - #clock-cells = <0>; - clock-output-names = "v2m:oscclk0"; - }; + oscclk0 { + /* MCC static memory clock */ + compatible = "arm,vexpress-osc"; + arm,vexpress-sysreg,func = <1 0>; + freq-range = <25000000 60000000>; + #clock-cells = <0>; + clock-output-names = "v2m:oscclk0"; + }; - v2m_oscclk1: oscclk1 { - /* CLCD clock */ - compatible = "arm,vexpress-osc"; - arm,vexpress-sysreg,func = <1 1>; - freq-range = <23750000 65000000>; - #clock-cells = <0>; - clock-output-names = "v2m:oscclk1"; - }; + v2m_oscclk1: oscclk1 { + /* CLCD clock */ + compatible = "arm,vexpress-osc"; + arm,vexpress-sysreg,func = <1 1>; + freq-range = <23750000 65000000>; + #clock-cells = <0>; + clock-output-names = "v2m:oscclk1"; + }; - v2m_oscclk2: oscclk2 { - /* IO FPGA peripheral clock */ - compatible = "arm,vexpress-osc"; - arm,vexpress-sysreg,func = <1 2>; - freq-range = <24000000 24000000>; - #clock-cells = <0>; - clock-output-names = "v2m:oscclk2"; - }; + v2m_oscclk2: oscclk2 { + /* IO FPGA peripheral clock */ + compatible = "arm,vexpress-osc"; + arm,vexpress-sysreg,func = <1 2>; + freq-range = <24000000 24000000>; + #clock-cells = <0>; + clock-output-names = "v2m:oscclk2"; + }; - volt-vio { - /* Logic level voltage */ - compatible = "arm,vexpress-volt"; - arm,vexpress-sysreg,func = <2 0>; - regulator-name = "VIO"; - regulator-always-on; - label = "VIO"; - }; + volt-vio { + /* Logic level voltage */ + compatible = "arm,vexpress-volt"; + arm,vexpress-sysreg,func = <2 0>; + regulator-name = "VIO"; + regulator-always-on; + label = "VIO"; + }; - temp-mcc { - /* MCC internal operating temperature */ - compatible = "arm,vexpress-temp"; - arm,vexpress-sysreg,func = <4 0>; - label = "MCC"; - }; + temp-mcc { + /* MCC internal operating temperature */ + compatible = "arm,vexpress-temp"; + arm,vexpress-sysreg,func = <4 0>; + label = "MCC"; + }; - reset { - compatible = "arm,vexpress-reset"; - arm,vexpress-sysreg,func = <5 0>; - }; + reset { + compatible = "arm,vexpress-reset"; + arm,vexpress-sysreg,func = <5 0>; + }; - muxfpga { - compatible = "arm,vexpress-muxfpga"; - arm,vexpress-sysreg,func = <7 0>; - }; + muxfpga { + compatible = "arm,vexpress-muxfpga"; + arm,vexpress-sysreg,func = <7 0>; + }; - shutdown { - compatible = "arm,vexpress-shutdown"; - arm,vexpress-sysreg,func = <8 0>; - }; + shutdown { + compatible = "arm,vexpress-shutdown"; + arm,vexpress-sysreg,func = <8 0>; + }; - reboot { - compatible = "arm,vexpress-reboot"; - arm,vexpress-sysreg,func = <9 0>; - }; + reboot { + compatible = "arm,vexpress-reboot"; + arm,vexpress-sysreg,func = <9 0>; + }; - dvimode { - compatible = "arm,vexpress-dvimode"; - arm,vexpress-sysreg,func = <11 0>; + dvimode { + compatible = "arm,vexpress-dvimode"; + arm,vexpress-sysreg,func = <11 0>; + }; }; }; }; +};
\ No newline at end of file diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts b/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts index a8ac4e2ed290..3971427a105b 100644 --- a/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts +++ b/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts @@ -9,6 +9,7 @@ */ /dts-v1/; +#include "vexpress-v2m-rs1.dtsi" / { model = "V2P-CA15"; @@ -278,8 +279,6 @@ <0 0 40 &gic 0 40 4>, <0 0 41 &gic 0 41 4>, <0 0 42 &gic 0 42 4>; - - /include/ "vexpress-v2m-rs1.dtsi" }; site2: hsb@40000000 { diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts index a4c7713edfcd..ac6b90e9d806 100644 --- a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts +++ b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts @@ -9,6 +9,7 @@ */ /dts-v1/; +#include "vexpress-v2m-rs1.dtsi" / { model = "V2P-CA15_CA7"; @@ -203,7 +204,7 @@ <1 10 0xf08>; }; - pmu_a15 { + pmu-a15 { compatible = "arm,cortex-a15-pmu"; interrupts = <0 68 4>, <0 69 4>; @@ -211,7 +212,7 @@ <&cpu1>; }; - pmu_a7 { + pmu-a7 { compatible = "arm,cortex-a7-pmu"; interrupts = <0 128 4>, <0 129 4>, @@ -584,7 +585,7 @@ }; }; - smb@8000000 { + smb: smb@8000000 { compatible = "simple-bus"; #address-cells = <2>; @@ -641,8 +642,6 @@ <0 0 40 &gic 0 40 4>, <0 0 41 &gic 0 41 4>, <0 0 42 &gic 0 42 4>; - - /include/ "vexpress-v2m-rs1.dtsi" }; site2: hsb@40000000 { diff --git a/arch/arm/boot/dts/vexpress-v2p-ca5s.dts b/arch/arm/boot/dts/vexpress-v2p-ca5s.dts index 32f1906ffecf..e5b4a7570a01 100644 --- a/arch/arm/boot/dts/vexpress-v2p-ca5s.dts +++ b/arch/arm/boot/dts/vexpress-v2p-ca5s.dts @@ -9,6 +9,7 @@ */ /dts-v1/; +#include "vexpress-v2m-rs1.dtsi" / { model = "V2P-CA5s"; @@ -191,7 +192,7 @@ }; }; - smb@8000000 { + smb: smb@8000000 { compatible = "simple-bus"; #address-cells = <2>; @@ -248,8 +249,6 @@ <0 0 40 &gic 0 40 4>, <0 0 41 &gic 0 41 4>, <0 0 42 &gic 0 42 4>; - - /include/ "vexpress-v2m-rs1.dtsi" }; site2: hsb@40000000 { diff --git a/arch/arm/boot/dts/vexpress-v2p-ca9.dts b/arch/arm/boot/dts/vexpress-v2p-ca9.dts index 5814460e0549..fc43873cbdff 100644 --- a/arch/arm/boot/dts/vexpress-v2p-ca9.dts +++ b/arch/arm/boot/dts/vexpress-v2p-ca9.dts @@ -9,6 +9,7 @@ */ /dts-v1/; +#include "vexpress-v2m.dtsi" / { model = "V2P-CA9"; @@ -301,7 +302,7 @@ }; }; - smb@4000000 { + smb: smb@4000000 { compatible = "simple-bus"; #address-cells = <2>; @@ -357,8 +358,6 @@ <0 0 40 &gic 0 40 4>, <0 0 41 &gic 0 41 4>, <0 0 42 &gic 0 42 4>; - - /include/ "vexpress-v2m.dtsi" }; site2: hsb@e0000000 { diff --git a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi index d8b2972527eb..e2da122a63f4 100644 --- a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi +++ b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi @@ -117,7 +117,7 @@ clocks = <&clk16m>; spi-max-frequency = <10000000>; interrupt-parent = <&gpio1>; - interrupts = <11 GPIO_ACTIVE_LOW>; + interrupts = <11 IRQ_TYPE_EDGE_RISING>; }; }; diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts index 782b69a3acdf..bd79e00bf615 100644 --- a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts +++ b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts @@ -70,8 +70,6 @@ compatible = "marvell,mv88e6085"; pinctrl-0 = <&pinctrl_gpio_switch0>; pinctrl-names = "default"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; dsa,member = <0 0>; interrupt-parent = <&gpio0>; @@ -156,8 +154,6 @@ compatible = "marvell,mv88e6085"; pinctrl-0 = <&pinctrl_gpio_switch1>; pinctrl-names = "default"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; dsa,member = <0 1>; interrupt-parent = <&gpio0>; @@ -243,8 +239,6 @@ switch2: switch@0 { compatible = "marvell,mv88e6085"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; dsa,member = <0 2>; diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts b/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts index c6f134c78303..0b1e94c6f25b 100644 --- a/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts +++ b/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts @@ -69,8 +69,6 @@ compatible = "marvell,mv88e6190"; pinctrl-0 = <&pinctrl_gpio_switch0>; pinctrl-names = "default"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; dsa,member = <0 0>; eeprom-length = <65536>; @@ -166,8 +164,6 @@ compatible = "marvell,mv88e6190"; pinctrl-0 = <&pinctrl_gpio_switch1>; pinctrl-names = "default"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; dsa,member = <0 1>; eeprom-length = <65536>; diff --git a/arch/arm/boot/dts/vf610-zii-dev.dtsi b/arch/arm/boot/dts/vf610-zii-dev.dtsi index 4890b8a5aa44..5ae5abfe1d55 100644 --- a/arch/arm/boot/dts/vf610-zii-dev.dtsi +++ b/arch/arm/boot/dts/vf610-zii-dev.dtsi @@ -222,6 +222,10 @@ status = "okay"; }; +&tempsensor { + io-channels = <&adc0 16>; +}; + &iomuxc { pinctrl_adc0_ad5: adc0ad5grp { fsl,pins = < diff --git a/arch/arm/boot/dts/vfxxx.dtsi b/arch/arm/boot/dts/vfxxx.dtsi index c3f09b737924..d392794d9c13 100644 --- a/arch/arm/boot/dts/vfxxx.dtsi +++ b/arch/arm/boot/dts/vfxxx.dtsi @@ -84,7 +84,7 @@ mask = <0x1000>; }; - iio-hwmon { + tempsensor: iio-hwmon { compatible = "iio-hwmon"; io-channels = <&adc0 16>, <&adc1 16>; }; diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile index 70b4a14ed993..1e9f7af8f70f 100644 --- a/arch/arm/common/Makefile +++ b/arch/arm/common/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_DMABOUNCE) += dmabounce.o obj-$(CONFIG_SHARP_LOCOMO) += locomo.o obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o obj-$(CONFIG_SHARP_SCOOP) += scoop.o +obj-$(CONFIG_SMP) += secure_cntvoff.o obj-$(CONFIG_PCI_HOST_ITE8152) += it8152.o obj-$(CONFIG_MCPM) += mcpm_head.o mcpm_entry.o mcpm_platsmp.o vlock.o CFLAGS_REMOVE_mcpm_entry.o = -pg diff --git a/arch/arm/common/mcpm_entry.c b/arch/arm/common/mcpm_entry.c index 2b913f17d50f..ad574d20415c 100644 --- a/arch/arm/common/mcpm_entry.c +++ b/arch/arm/common/mcpm_entry.c @@ -9,6 +9,7 @@ * published by the Free Software Foundation. */ +#include <linux/export.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/irqflags.h> @@ -174,6 +175,7 @@ bool mcpm_is_available(void) { return (platform_ops) ? true : false; } +EXPORT_SYMBOL_GPL(mcpm_is_available); /* * We can't use regular spinlocks. In the switcher case, it is possible diff --git a/arch/arm/common/secure_cntvoff.S b/arch/arm/common/secure_cntvoff.S new file mode 100644 index 000000000000..53fc7bdb6c2e --- /dev/null +++ b/arch/arm/common/secure_cntvoff.S @@ -0,0 +1,32 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2014 Renesas Electronics Corporation + * + * Initialization of CNTVOFF register from secure mode + * + */ + +#include <linux/linkage.h> +#include <asm/assembler.h> + +ENTRY(secure_cntvoff_init) + .arch armv7-a + /* + * CNTVOFF has to be initialized either from non-secure Hypervisor + * mode or secure Monitor mode with SCR.NS==1. If TrustZone is enabled + * then it should be handled by the secure code. The CPU must implement + * the virtualization extensions. + */ + cps #MON_MODE + mrc p15, 0, r1, c1, c1, 0 /* Get Secure Config */ + orr r0, r1, #1 + mcr p15, 0, r0, c1, c1, 0 /* Set Non Secure bit */ + isb + mov r0, #0 + mcrr p15, 4, r0, r0, c14 /* CNTVOFF = 0 */ + isb + mcr p15, 0, r1, c1, c1, 0 /* Set Secure bit */ + isb + cps #SVC_MODE + ret lr +ENDPROC(secure_cntvoff_init) diff --git a/arch/arm/configs/bcm2835_defconfig b/arch/arm/configs/bcm2835_defconfig index 8682b15336b9..e4d188f0a4b4 100644 --- a/arch/arm/configs/bcm2835_defconfig +++ b/arch/arm/configs/bcm2835_defconfig @@ -64,6 +64,7 @@ CONFIG_BLK_DEV_SD=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_SCAN_ASYNC=y CONFIG_NETDEVICES=y +CONFIG_USB_LAN78XX=y CONFIG_USB_USBNET=y CONFIG_USB_NET_SMSC95XX=y CONFIG_BRCMFMAC=m @@ -127,6 +128,7 @@ CONFIG_LEDS_TRIGGER_CAMERA=y CONFIG_DMADEVICES=y CONFIG_DMA_BCM2835=y CONFIG_STAGING=y +CONFIG_BCM2835_VCHIQ=m CONFIG_MAILBOX=y CONFIG_BCM2835_MBOX=y # CONFIG_IOMMU_SUPPORT is not set diff --git a/arch/arm/configs/davinci_all_defconfig b/arch/arm/configs/davinci_all_defconfig index c302a04e8cbc..21b2d7791df4 100644 --- a/arch/arm/configs/davinci_all_defconfig +++ b/arch/arm/configs/davinci_all_defconfig @@ -56,7 +56,7 @@ CONFIG_IP_PNP_DHCP=y CONFIG_NETFILTER=y CONFIG_DEVTMPFS=y CONFIG_DEVTMPFS_MOUNT=y -# CONFIG_FW_LOADER is not set +CONFIG_FW_LOADER=m CONFIG_DMA_CMA=y CONFIG_DA8XX_MSTPRI=y CONFIG_MTD=m @@ -212,6 +212,8 @@ CONFIG_RTC_CLASS=y CONFIG_RTC_DRV_OMAP=m CONFIG_DMADEVICES=y CONFIG_TI_EDMA=y +CONFIG_REMOTEPROC=m +CONFIG_DA8XX_REMOTEPROC=m CONFIG_MEMORY=y CONFIG_TI_AEMIF=m CONFIG_DA8XX_DDRCTL=y diff --git a/arch/arm/configs/exynos_defconfig b/arch/arm/configs/exynos_defconfig index 629189c62fd1..85b2369d6b20 100644 --- a/arch/arm/configs/exynos_defconfig +++ b/arch/arm/configs/exynos_defconfig @@ -208,6 +208,7 @@ CONFIG_DRM_EXYNOS_DSI=y CONFIG_DRM_EXYNOS_HDMI=y CONFIG_DRM_PANEL_SIMPLE=y CONFIG_DRM_PANEL_SAMSUNG_LD9040=y +CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03=y CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0=y CONFIG_DRM_NXP_PTN3460=y CONFIG_DRM_PARADE_PS8622=y diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig index 3a308437b088..f70507ab91ee 100644 --- a/arch/arm/configs/imx_v6_v7_defconfig +++ b/arch/arm/configs/imx_v6_v7_defconfig @@ -38,6 +38,7 @@ CONFIG_SOC_IMX51=y CONFIG_SOC_IMX53=y CONFIG_SOC_IMX6Q=y CONFIG_SOC_IMX6SL=y +CONFIG_SOC_IMX6SLL=y CONFIG_SOC_IMX6SX=y CONFIG_SOC_IMX6UL=y CONFIG_SOC_IMX7D=y @@ -153,6 +154,9 @@ CONFIG_USB_RTL8152=m CONFIG_USB_USBNET=y CONFIG_USB_NET_CDC_EEM=m CONFIG_BRCMFMAC=m +CONFIG_MWIFIEX=m +CONFIG_MWIFIEX_SDIO=m +CONFIG_MWIFIEX_PCIE=m CONFIG_WL12XX=m CONFIG_WL18XX=m CONFIG_WLCORE_SDIO=m @@ -199,6 +203,7 @@ CONFIG_SPI_GPIO=y CONFIG_SPI_IMX=y CONFIG_SPI_FSL_DSPI=y CONFIG_GPIO_SYSFS=y +CONFIG_GPIO_MAX732X=y CONFIG_GPIO_MC9S08DZ60=y CONFIG_GPIO_PCA953X=y CONFIG_GPIO_STMPE=y @@ -214,11 +219,13 @@ CONFIG_CPU_THERMAL=y CONFIG_IMX_THERMAL=y CONFIG_WATCHDOG=y CONFIG_DA9062_WATCHDOG=y +CONFIG_RN5T618_WATCHDOG=y CONFIG_IMX2_WDT=y CONFIG_MFD_DA9052_I2C=y CONFIG_MFD_DA9062=y CONFIG_MFD_MC13XXX_SPI=y CONFIG_MFD_MC13XXX_I2C=y +CONFIG_MFD_RN5T618=y CONFIG_MFD_STMPE=y CONFIG_REGULATOR=y CONFIG_REGULATOR_FIXED_VOLTAGE=y @@ -229,6 +236,7 @@ CONFIG_REGULATOR_GPIO=y CONFIG_REGULATOR_MC13783=y CONFIG_REGULATOR_MC13892=y CONFIG_REGULATOR_PFUZE100=y +CONFIG_REGULATOR_RN5T618=y CONFIG_RC_CORE=y CONFIG_RC_DEVICES=y CONFIG_IR_GPIO_CIR=y @@ -374,6 +382,7 @@ CONFIG_PWM=y CONFIG_PWM_FSL_FTM=y CONFIG_PWM_IMX=y CONFIG_NVMEM_IMX_OCOTP=y +CONFIG_NVMEM_VF610_OCOTP=y CONFIG_TEE=y CONFIG_OPTEE=y CONFIG_MUX_MMIO=y diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig index e6b3c96d4c09..7e1c543162c3 100644 --- a/arch/arm/configs/multi_v7_defconfig +++ b/arch/arm/configs/multi_v7_defconfig @@ -90,6 +90,7 @@ CONFIG_ARCH_R8A73A4=y CONFIG_ARCH_R8A7740=y CONFIG_ARCH_R8A7743=y CONFIG_ARCH_R8A7745=y +CONFIG_ARCH_R8A77470=y CONFIG_ARCH_R8A7778=y CONFIG_ARCH_R8A7779=y CONFIG_ARCH_R8A7790=y @@ -187,6 +188,8 @@ CONFIG_B53_MMAP_DRIVER=m CONFIG_B53_SRAB_DRIVER=m CONFIG_CAN_SUN4I=y CONFIG_BT=m +CONFIG_BT_HCIUART=m +CONFIG_BT_HCIUART_BCM=y CONFIG_BT_MRVL=m CONFIG_BT_MRVL_SDIO=m CONFIG_CFG80211=m @@ -280,6 +283,7 @@ CONFIG_FIXED_PHY=y CONFIG_ROCKCHIP_PHY=y CONFIG_USB_PEGASUS=y CONFIG_USB_RTL8152=m +CONFIG_USB_LAN78XX=m CONFIG_USB_USBNET=y CONFIG_USB_NET_SMSC75XX=y CONFIG_USB_NET_SMSC95XX=y @@ -360,10 +364,12 @@ CONFIG_SERIAL_ST_ASC=y CONFIG_SERIAL_ST_ASC_CONSOLE=y CONFIG_SERIAL_STM32=y CONFIG_SERIAL_STM32_CONSOLE=y +CONFIG_SERIAL_DEV_BUS=y CONFIG_HVC_DRIVER=y CONFIG_VIRTIO_CONSOLE=y CONFIG_I2C_CHARDEV=y CONFIG_I2C_DAVINCI=y +CONFIG_I2C_MESON=y CONFIG_I2C_MUX=y CONFIG_I2C_ARB_GPIO_CHALLENGE=m CONFIG_I2C_MUX_PCA954x=y @@ -385,6 +391,7 @@ CONFIG_I2C_S3C2410=y CONFIG_I2C_SH_MOBILE=y CONFIG_I2C_SIRF=y CONFIG_I2C_ST=y +CONFIG_I2C_STM32F7=y CONFIG_I2C_SUN6I_P2WI=y CONFIG_I2C_TEGRA=y CONFIG_I2C_UNIPHIER=y @@ -497,6 +504,7 @@ CONFIG_TEGRA_WATCHDOG=m CONFIG_MESON_WATCHDOG=y CONFIG_DW_WATCHDOG=y CONFIG_DIGICOLOR_WATCHDOG=y +CONFIG_RENESAS_WDT=m CONFIG_BCM2835_WDT=y CONFIG_BCM47XX_WDT=y CONFIG_BCM7038_WDT=m @@ -638,6 +646,7 @@ CONFIG_DRM_SUN4I=m CONFIG_DRM_FSL_DCU=m CONFIG_DRM_TEGRA=y CONFIG_DRM_PANEL_SAMSUNG_LD9040=m +CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03=m CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0=m CONFIG_DRM_PANEL_SIMPLE=y CONFIG_DRM_SII9234=m @@ -650,7 +659,6 @@ CONFIG_FB_EFI=y CONFIG_FB_WM8505=y CONFIG_FB_SH_MOBILE_LCDC=y CONFIG_FB_SIMPLE=y -CONFIG_FB_SH_MOBILE_MERAM=y CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_BACKLIGHT_CLASS_DEVICE=y CONFIG_LCD_PLATFORM=m @@ -947,6 +955,7 @@ CONFIG_PWM_ATMEL=m CONFIG_PWM_ATMEL_HLCDC_PWM=m CONFIG_PWM_ATMEL_TCB=m CONFIG_PWM_FSL_FTM=m +CONFIG_PWM_MESON=m CONFIG_PWM_RCAR=m CONFIG_PWM_RENESAS_TPU=y CONFIG_PWM_ROCKCHIP=m @@ -972,6 +981,7 @@ CONFIG_PHY_QCOM_APQ8064_SATA=m CONFIG_PHY_MIPHY28LP=y CONFIG_PHY_RCAR_GEN2=m CONFIG_PHY_STIH407_USB=y +CONFIG_PHY_STM32_USBPHYC=y CONFIG_PHY_SUN4I_USB=y CONFIG_PHY_SUN9I_USB=y CONFIG_PHY_SAMSUNG_USB2=m diff --git a/arch/arm/configs/shmobile_defconfig b/arch/arm/configs/shmobile_defconfig index a701601fbd76..b49887e86a3d 100644 --- a/arch/arm/configs/shmobile_defconfig +++ b/arch/arm/configs/shmobile_defconfig @@ -14,6 +14,7 @@ CONFIG_ARCH_R8A73A4=y CONFIG_ARCH_R8A7740=y CONFIG_ARCH_R8A7743=y CONFIG_ARCH_R8A7745=y +CONFIG_ARCH_R8A77470=y CONFIG_ARCH_R8A7778=y CONFIG_ARCH_R8A7779=y CONFIG_ARCH_R8A7790=y @@ -127,6 +128,7 @@ CONFIG_CPU_THERMAL=y CONFIG_RCAR_THERMAL=y CONFIG_WATCHDOG=y CONFIG_DA9063_WATCHDOG=y +CONFIG_RENESAS_WDT=y CONFIG_MFD_AS3711=y CONFIG_MFD_DA9063=y CONFIG_REGULATOR_FIXED_VOLTAGE=y @@ -156,7 +158,6 @@ CONFIG_DRM_DUMB_VGA_DAC=y CONFIG_DRM_I2C_ADV7511=y CONFIG_DRM_I2C_ADV7511_AUDIO=y CONFIG_FB_SH_MOBILE_LCDC=y -CONFIG_FB_SH_MOBILE_MERAM=y # CONFIG_LCD_CLASS_DEVICE is not set # CONFIG_BACKLIGHT_GENERIC is not set CONFIG_BACKLIGHT_PWM=y diff --git a/arch/arm/crypto/sha1-armv4-large.S b/arch/arm/crypto/sha1-armv4-large.S index 99207c45ec10..f82cd8cf5a09 100644 --- a/arch/arm/crypto/sha1-armv4-large.S +++ b/arch/arm/crypto/sha1-armv4-large.S @@ -1,4 +1,14 @@ #define __ARM_ARCH__ __LINUX_ARM_ARCH__ +@ SPDX-License-Identifier: GPL-2.0 + +@ This code is taken from the OpenSSL project but the author (Andy Polyakov) +@ has relicensed it under the GPLv2. Therefore this program is free software; +@ you can redistribute it and/or modify it under the terms of the GNU General +@ Public License version 2 as published by the Free Software Foundation. +@ +@ The original headers, including the original license headers, are +@ included below for completeness. + @ ==================================================================== @ Written by Andy Polyakov <appro@fy.chalmers.se> for the OpenSSL @ project. The module is, however, dual licensed under OpenSSL and diff --git a/arch/arm/crypto/sha256-armv4.pl b/arch/arm/crypto/sha256-armv4.pl index fac0533ea633..b9ec44060ed3 100644 --- a/arch/arm/crypto/sha256-armv4.pl +++ b/arch/arm/crypto/sha256-armv4.pl @@ -1,12 +1,19 @@ #!/usr/bin/env perl +# SPDX-License-Identifier: GPL-2.0 + +# This code is taken from the OpenSSL project but the author (Andy Polyakov) +# has relicensed it under the GPLv2. Therefore this program is free software; +# you can redistribute it and/or modify it under the terms of the GNU General +# Public License version 2 as published by the Free Software Foundation. +# +# The original headers, including the original license headers, are +# included below for completeness. # ==================================================================== # Written by Andy Polyakov <appro@openssl.org> for the OpenSSL # project. The module is, however, dual licensed under OpenSSL and # CRYPTOGAMS licenses depending on where you obtain it. For further # details see http://www.openssl.org/~appro/cryptogams/. -# -# Permission to use under GPL terms is granted. # ==================================================================== # SHA256 block procedure for ARMv4. May 2007. diff --git a/arch/arm/crypto/sha256-core.S_shipped b/arch/arm/crypto/sha256-core.S_shipped index 555a1a8eec90..3b58300d611c 100644 --- a/arch/arm/crypto/sha256-core.S_shipped +++ b/arch/arm/crypto/sha256-core.S_shipped @@ -1,11 +1,18 @@ +@ SPDX-License-Identifier: GPL-2.0 + +@ This code is taken from the OpenSSL project but the author (Andy Polyakov) +@ has relicensed it under the GPLv2. Therefore this program is free software; +@ you can redistribute it and/or modify it under the terms of the GNU General +@ Public License version 2 as published by the Free Software Foundation. +@ +@ The original headers, including the original license headers, are +@ included below for completeness. @ ==================================================================== @ Written by Andy Polyakov <appro@openssl.org> for the OpenSSL @ project. The module is, however, dual licensed under OpenSSL and @ CRYPTOGAMS licenses depending on where you obtain it. For further @ details see http://www.openssl.org/~appro/cryptogams/. -@ -@ Permission to use under GPL terms is granted. @ ==================================================================== @ SHA256 block procedure for ARMv4. May 2007. diff --git a/arch/arm/crypto/sha512-armv4.pl b/arch/arm/crypto/sha512-armv4.pl index a2b11a844357..fb5d15048c0b 100644 --- a/arch/arm/crypto/sha512-armv4.pl +++ b/arch/arm/crypto/sha512-armv4.pl @@ -1,12 +1,19 @@ #!/usr/bin/env perl +# SPDX-License-Identifier: GPL-2.0 + +# This code is taken from the OpenSSL project but the author (Andy Polyakov) +# has relicensed it under the GPLv2. Therefore this program is free software; +# you can redistribute it and/or modify it under the terms of the GNU General +# Public License version 2 as published by the Free Software Foundation. +# +# The original headers, including the original license headers, are +# included below for completeness. # ==================================================================== # Written by Andy Polyakov <appro@openssl.org> for the OpenSSL # project. The module is, however, dual licensed under OpenSSL and # CRYPTOGAMS licenses depending on where you obtain it. For further # details see http://www.openssl.org/~appro/cryptogams/. -# -# Permission to use under GPL terms is granted. # ==================================================================== # SHA512 block procedure for ARMv4. September 2007. diff --git a/arch/arm/crypto/sha512-core.S_shipped b/arch/arm/crypto/sha512-core.S_shipped index 3694c4d4ca2b..b1c334a49cda 100644 --- a/arch/arm/crypto/sha512-core.S_shipped +++ b/arch/arm/crypto/sha512-core.S_shipped @@ -1,11 +1,18 @@ +@ SPDX-License-Identifier: GPL-2.0 + +@ This code is taken from the OpenSSL project but the author (Andy Polyakov) +@ has relicensed it under the GPLv2. Therefore this program is free software; +@ you can redistribute it and/or modify it under the terms of the GNU General +@ Public License version 2 as published by the Free Software Foundation. +@ +@ The original headers, including the original license headers, are +@ included below for completeness. @ ==================================================================== @ Written by Andy Polyakov <appro@openssl.org> for the OpenSSL @ project. The module is, however, dual licensed under OpenSSL and @ CRYPTOGAMS licenses depending on where you obtain it. For further @ details see http://www.openssl.org/~appro/cryptogams/. -@ -@ Permission to use under GPL terms is granted. @ ==================================================================== @ SHA512 block procedure for ARMv4. September 2007. diff --git a/arch/arm/include/asm/Kbuild b/arch/arm/include/asm/Kbuild index 873e3c189279..1d66db9c9db5 100644 --- a/arch/arm/include/asm/Kbuild +++ b/arch/arm/include/asm/Kbuild @@ -1,3 +1,4 @@ +generic-y += compat.h generic-y += current.h generic-y += early_ioremap.h generic-y += emergency-restart.h diff --git a/arch/arm/include/asm/assembler.h b/arch/arm/include/asm/assembler.h index bc8d4bbd82e2..0cd4dccbae78 100644 --- a/arch/arm/include/asm/assembler.h +++ b/arch/arm/include/asm/assembler.h @@ -447,6 +447,14 @@ THUMB( orr \reg , \reg , #PSR_T_BIT ) .size \name , . - \name .endm + .macro csdb +#ifdef CONFIG_THUMB2_KERNEL + .inst.w 0xf3af8014 +#else + .inst 0xe320f014 +#endif + .endm + .macro check_uaccess, addr:req, size:req, limit:req, tmp:req, bad:req #ifndef CONFIG_CPU_USE_DOMAINS adds \tmp, \addr, #\size - 1 @@ -536,4 +544,14 @@ THUMB( orr \reg , \reg , #PSR_T_BIT ) #endif .endm +#ifdef CONFIG_KPROBES +#define _ASM_NOKPROBE(entry) \ + .pushsection "_kprobe_blacklist", "aw" ; \ + .balign 4 ; \ + .long entry; \ + .popsection +#else +#define _ASM_NOKPROBE(entry) +#endif + #endif /* __ASM_ASSEMBLER_H__ */ diff --git a/arch/arm/include/asm/barrier.h b/arch/arm/include/asm/barrier.h index 40f5c410fd8c..69772e742a0a 100644 --- a/arch/arm/include/asm/barrier.h +++ b/arch/arm/include/asm/barrier.h @@ -17,6 +17,12 @@ #define isb(option) __asm__ __volatile__ ("isb " #option : : : "memory") #define dsb(option) __asm__ __volatile__ ("dsb " #option : : : "memory") #define dmb(option) __asm__ __volatile__ ("dmb " #option : : : "memory") +#ifdef CONFIG_THUMB2_KERNEL +#define CSDB ".inst.w 0xf3af8014" +#else +#define CSDB ".inst 0xe320f014" +#endif +#define csdb() __asm__ __volatile__(CSDB : : : "memory") #elif defined(CONFIG_CPU_XSC3) || __LINUX_ARM_ARCH__ == 6 #define isb(x) __asm__ __volatile__ ("mcr p15, 0, %0, c7, c5, 4" \ : : "r" (0) : "memory") @@ -37,6 +43,13 @@ #define dmb(x) __asm__ __volatile__ ("" : : : "memory") #endif +#ifndef CSDB +#define CSDB +#endif +#ifndef csdb +#define csdb() +#endif + #ifdef CONFIG_ARM_HEAVY_MB extern void (*soc_mb)(void); extern void arm_heavy_mb(void); @@ -63,6 +76,25 @@ extern void arm_heavy_mb(void); #define __smp_rmb() __smp_mb() #define __smp_wmb() dmb(ishst) +#ifdef CONFIG_CPU_SPECTRE +static inline unsigned long array_index_mask_nospec(unsigned long idx, + unsigned long sz) +{ + unsigned long mask; + + asm volatile( + "cmp %1, %2\n" + " sbc %0, %1, %1\n" + CSDB + : "=r" (mask) + : "r" (idx), "Ir" (sz) + : "cc"); + + return mask; +} +#define array_index_mask_nospec array_index_mask_nospec +#endif + #include <asm-generic/barrier.h> #endif /* !__ASSEMBLY__ */ diff --git a/arch/arm/include/asm/bugs.h b/arch/arm/include/asm/bugs.h index a97f1ea708d1..73a99c72a930 100644 --- a/arch/arm/include/asm/bugs.h +++ b/arch/arm/include/asm/bugs.h @@ -10,12 +10,14 @@ #ifndef __ASM_BUGS_H #define __ASM_BUGS_H -#ifdef CONFIG_MMU extern void check_writebuffer_bugs(void); -#define check_bugs() check_writebuffer_bugs() +#ifdef CONFIG_MMU +extern void check_bugs(void); +extern void check_other_bugs(void); #else #define check_bugs() do { } while (0) +#define check_other_bugs() do { } while (0) #endif #endif diff --git a/arch/arm/include/asm/cp15.h b/arch/arm/include/asm/cp15.h index 4c9fa72b59f5..07e27f212dc7 100644 --- a/arch/arm/include/asm/cp15.h +++ b/arch/arm/include/asm/cp15.h @@ -65,6 +65,9 @@ #define __write_sysreg(v, r, w, c, t) asm volatile(w " " c : : "r" ((t)(v))) #define write_sysreg(v, ...) __write_sysreg(v, __VA_ARGS__) +#define BPIALL __ACCESS_CP15(c7, 0, c5, 6) +#define ICIALLU __ACCESS_CP15(c7, 0, c5, 0) + extern unsigned long cr_alignment; /* defined in entry-armv.S */ static inline unsigned long get_cr(void) diff --git a/arch/arm/include/asm/cputype.h b/arch/arm/include/asm/cputype.h index cb546425da8a..0d289240b6ca 100644 --- a/arch/arm/include/asm/cputype.h +++ b/arch/arm/include/asm/cputype.h @@ -2,9 +2,6 @@ #ifndef __ASM_ARM_CPUTYPE_H #define __ASM_ARM_CPUTYPE_H -#include <linux/stringify.h> -#include <linux/kernel.h> - #define CPUID_ID 0 #define CPUID_CACHETYPE 1 #define CPUID_TCM 2 @@ -62,6 +59,7 @@ ((mpidr >> (MPIDR_LEVEL_BITS * level)) & MPIDR_LEVEL_MASK) #define ARM_CPU_IMP_ARM 0x41 +#define ARM_CPU_IMP_BRCM 0x42 #define ARM_CPU_IMP_DEC 0x44 #define ARM_CPU_IMP_INTEL 0x69 @@ -77,8 +75,17 @@ #define ARM_CPU_PART_CORTEX_A12 0x4100c0d0 #define ARM_CPU_PART_CORTEX_A17 0x4100c0e0 #define ARM_CPU_PART_CORTEX_A15 0x4100c0f0 +#define ARM_CPU_PART_CORTEX_A53 0x4100d030 +#define ARM_CPU_PART_CORTEX_A57 0x4100d070 +#define ARM_CPU_PART_CORTEX_A72 0x4100d080 +#define ARM_CPU_PART_CORTEX_A73 0x4100d090 +#define ARM_CPU_PART_CORTEX_A75 0x4100d0a0 #define ARM_CPU_PART_MASK 0xff00fff0 +/* Broadcom implemented processors */ +#define ARM_CPU_PART_BRAHMA_B15 0x420000f0 +#define ARM_CPU_PART_BRAHMA_B53 0x42001000 + /* DEC implemented cores */ #define ARM_CPU_PART_SA1100 0x4400a110 @@ -98,6 +105,11 @@ /* Qualcomm implemented cores */ #define ARM_CPU_PART_SCORPION 0x510002d0 +#ifndef __ASSEMBLY__ + +#include <linux/stringify.h> +#include <linux/kernel.h> + extern unsigned int processor_id; #ifdef CONFIG_CPU_CP15 @@ -326,4 +338,6 @@ static inline int __attribute_const__ cpuid_feature_extract_field(u32 features, #define cpuid_feature_extract(reg, field) \ cpuid_feature_extract_field(read_cpuid_ext(reg), field) +#endif /* __ASSEMBLY__ */ + #endif diff --git a/arch/arm/include/asm/kgdb.h b/arch/arm/include/asm/kgdb.h index 3b73fdcf3627..8de1100d1067 100644 --- a/arch/arm/include/asm/kgdb.h +++ b/arch/arm/include/asm/kgdb.h @@ -77,7 +77,7 @@ extern int kgdb_fault_expected; #define KGDB_MAX_NO_CPUS 1 #define BUFMAX 400 -#define NUMREGBYTES (DBG_MAX_REG_NUM << 2) +#define NUMREGBYTES (GDB_MAX_REGS << 2) #define NUMCRITREGBYTES (32 << 2) #define _R0 0 diff --git a/arch/arm/include/asm/kvm_asm.h b/arch/arm/include/asm/kvm_asm.h index 5a953ecb0d78..231e87ad45d5 100644 --- a/arch/arm/include/asm/kvm_asm.h +++ b/arch/arm/include/asm/kvm_asm.h @@ -61,8 +61,6 @@ struct kvm_vcpu; extern char __kvm_hyp_init[]; extern char __kvm_hyp_init_end[]; -extern char __kvm_hyp_vector[]; - extern void __kvm_flush_vm_context(void); extern void __kvm_tlb_flush_vmid_ipa(struct kvm *kvm, phys_addr_t ipa); extern void __kvm_tlb_flush_vmid(struct kvm *kvm); diff --git a/arch/arm/include/asm/kvm_host.h b/arch/arm/include/asm/kvm_host.h index c7c28c885a19..1f1fe4109b02 100644 --- a/arch/arm/include/asm/kvm_host.h +++ b/arch/arm/include/asm/kvm_host.h @@ -21,6 +21,7 @@ #include <linux/types.h> #include <linux/kvm_types.h> +#include <asm/cputype.h> #include <asm/kvm.h> #include <asm/kvm_asm.h> #include <asm/kvm_mmio.h> @@ -280,6 +281,7 @@ void kvm_mmu_wp_memory_region(struct kvm *kvm, int slot); struct kvm_vcpu *kvm_mpidr_to_vcpu(struct kvm *kvm, unsigned long mpidr); +static inline bool kvm_arch_check_sve_has_vhe(void) { return true; } static inline void kvm_arch_hardware_unsetup(void) {} static inline void kvm_arch_sync_events(struct kvm *kvm) {} static inline void kvm_arch_vcpu_uninit(struct kvm_vcpu *vcpu) {} @@ -303,19 +305,49 @@ int kvm_arm_vcpu_arch_get_attr(struct kvm_vcpu *vcpu, int kvm_arm_vcpu_arch_has_attr(struct kvm_vcpu *vcpu, struct kvm_device_attr *attr); -/* All host FP/SIMD state is restored on guest exit, so nothing to save: */ -static inline void kvm_fpsimd_flush_cpu_state(void) {} +/* + * VFP/NEON switching is all done by the hyp switch code, so no need to + * coordinate with host context handling for this state: + */ +static inline void kvm_arch_vcpu_load_fp(struct kvm_vcpu *vcpu) {} +static inline void kvm_arch_vcpu_ctxsync_fp(struct kvm_vcpu *vcpu) {} +static inline void kvm_arch_vcpu_put_fp(struct kvm_vcpu *vcpu) {} static inline void kvm_arm_vhe_guest_enter(void) {} static inline void kvm_arm_vhe_guest_exit(void) {} static inline bool kvm_arm_harden_branch_predictor(void) { + switch(read_cpuid_part()) { +#ifdef CONFIG_HARDEN_BRANCH_PREDICTOR + case ARM_CPU_PART_BRAHMA_B15: + case ARM_CPU_PART_CORTEX_A12: + case ARM_CPU_PART_CORTEX_A15: + case ARM_CPU_PART_CORTEX_A17: + return true; +#endif + default: + return false; + } +} + +#define KVM_SSBD_UNKNOWN -1 +#define KVM_SSBD_FORCE_DISABLE 0 +#define KVM_SSBD_KERNEL 1 +#define KVM_SSBD_FORCE_ENABLE 2 +#define KVM_SSBD_MITIGATED 3 + +static inline int kvm_arm_have_ssbd(void) +{ /* No way to detect it yet, pretend it is not there. */ - return false; + return KVM_SSBD_UNKNOWN; } static inline void kvm_vcpu_load_sysregs(struct kvm_vcpu *vcpu) {} static inline void kvm_vcpu_put_sysregs(struct kvm_vcpu *vcpu) {} +#define __KVM_HAVE_ARCH_VM_ALLOC +struct kvm *kvm_arch_alloc_vm(void); +void kvm_arch_free_vm(struct kvm *kvm); + #endif /* __ARM_KVM_HOST_H__ */ diff --git a/arch/arm/include/asm/kvm_mmu.h b/arch/arm/include/asm/kvm_mmu.h index f675162663f0..8553d68b7c8a 100644 --- a/arch/arm/include/asm/kvm_mmu.h +++ b/arch/arm/include/asm/kvm_mmu.h @@ -327,7 +327,28 @@ static inline int kvm_read_guest_lock(struct kvm *kvm, static inline void *kvm_get_hyp_vector(void) { - return kvm_ksym_ref(__kvm_hyp_vector); + switch(read_cpuid_part()) { +#ifdef CONFIG_HARDEN_BRANCH_PREDICTOR + case ARM_CPU_PART_CORTEX_A12: + case ARM_CPU_PART_CORTEX_A17: + { + extern char __kvm_hyp_vector_bp_inv[]; + return kvm_ksym_ref(__kvm_hyp_vector_bp_inv); + } + + case ARM_CPU_PART_BRAHMA_B15: + case ARM_CPU_PART_CORTEX_A15: + { + extern char __kvm_hyp_vector_ic_inv[]; + return kvm_ksym_ref(__kvm_hyp_vector_ic_inv); + } +#endif + default: + { + extern char __kvm_hyp_vector[]; + return kvm_ksym_ref(__kvm_hyp_vector); + } + } } static inline int kvm_map_vectors(void) @@ -335,6 +356,11 @@ static inline int kvm_map_vectors(void) return 0; } +static inline int hyp_map_aux_data(void) +{ + return 0; +} + #define kvm_phys_to_vttbr(addr) (addr) #endif /* !__ASSEMBLY__ */ diff --git a/arch/arm/include/asm/mpu.h b/arch/arm/include/asm/mpu.h index 6d1491c8ee22..5e088c83d3d8 100644 --- a/arch/arm/include/asm/mpu.h +++ b/arch/arm/include/asm/mpu.h @@ -12,60 +12,101 @@ /* ID_MMFR0 data relevant to MPU */ #define MMFR0_PMSA (0xF << 4) #define MMFR0_PMSAv7 (3 << 4) +#define MMFR0_PMSAv8 (4 << 4) /* MPU D/I Size Register fields */ -#define MPU_RSR_SZ 1 -#define MPU_RSR_EN 0 -#define MPU_RSR_SD 8 +#define PMSAv7_RSR_SZ 1 +#define PMSAv7_RSR_EN 0 +#define PMSAv7_RSR_SD 8 /* Number of subregions (SD) */ -#define MPU_NR_SUBREGS 8 -#define MPU_MIN_SUBREG_SIZE 256 +#define PMSAv7_NR_SUBREGS 8 +#define PMSAv7_MIN_SUBREG_SIZE 256 /* The D/I RSR value for an enabled region spanning the whole of memory */ -#define MPU_RSR_ALL_MEM 63 +#define PMSAv7_RSR_ALL_MEM 63 /* Individual bits in the DR/IR ACR */ -#define MPU_ACR_XN (1 << 12) -#define MPU_ACR_SHARED (1 << 2) +#define PMSAv7_ACR_XN (1 << 12) +#define PMSAv7_ACR_SHARED (1 << 2) /* C, B and TEX[2:0] bits only have semantic meanings when grouped */ -#define MPU_RGN_CACHEABLE 0xB -#define MPU_RGN_SHARED_CACHEABLE (MPU_RGN_CACHEABLE | MPU_ACR_SHARED) -#define MPU_RGN_STRONGLY_ORDERED 0 +#define PMSAv7_RGN_CACHEABLE 0xB +#define PMSAv7_RGN_SHARED_CACHEABLE (PMSAv7_RGN_CACHEABLE | PMSAv7_ACR_SHARED) +#define PMSAv7_RGN_STRONGLY_ORDERED 0 /* Main region should only be shared for SMP */ #ifdef CONFIG_SMP -#define MPU_RGN_NORMAL (MPU_RGN_CACHEABLE | MPU_ACR_SHARED) +#define PMSAv7_RGN_NORMAL (PMSAv7_RGN_CACHEABLE | PMSAv7_ACR_SHARED) #else -#define MPU_RGN_NORMAL MPU_RGN_CACHEABLE +#define PMSAv7_RGN_NORMAL PMSAv7_RGN_CACHEABLE #endif /* Access permission bits of ACR (only define those that we use)*/ -#define MPU_AP_PL1RO_PL0NA (0x5 << 8) -#define MPU_AP_PL1RW_PL0RW (0x3 << 8) -#define MPU_AP_PL1RW_PL0R0 (0x2 << 8) -#define MPU_AP_PL1RW_PL0NA (0x1 << 8) +#define PMSAv7_AP_PL1RO_PL0NA (0x5 << 8) +#define PMSAv7_AP_PL1RW_PL0RW (0x3 << 8) +#define PMSAv7_AP_PL1RW_PL0R0 (0x2 << 8) +#define PMSAv7_AP_PL1RW_PL0NA (0x1 << 8) + +#define PMSAv8_BAR_XN 1 + +#define PMSAv8_LAR_EN 1 +#define PMSAv8_LAR_IDX(n) (((n) & 0x7) << 1) + + +#define PMSAv8_AP_PL1RW_PL0NA (0 << 1) +#define PMSAv8_AP_PL1RW_PL0RW (1 << 1) +#define PMSAv8_AP_PL1RO_PL0RO (3 << 1) + +#ifdef CONFIG_SMP +#define PMSAv8_RGN_SHARED (3 << 3) // inner sharable +#else +#define PMSAv8_RGN_SHARED (0 << 3) +#endif + +#define PMSAv8_RGN_DEVICE_nGnRnE 0 +#define PMSAv8_RGN_NORMAL 1 + +#define PMSAv8_MAIR(attr, mt) ((attr) << ((mt) * 8)) + +#ifdef CONFIG_CPU_V7M +#define PMSAv8_MINALIGN 32 +#else +#define PMSAv8_MINALIGN 64 +#endif /* For minimal static MPU region configurations */ -#define MPU_PROBE_REGION 0 -#define MPU_BG_REGION 1 -#define MPU_RAM_REGION 2 -#define MPU_ROM_REGION 3 +#define PMSAv7_PROBE_REGION 0 +#define PMSAv7_BG_REGION 1 +#define PMSAv7_RAM_REGION 2 +#define PMSAv7_ROM_REGION 3 + +/* Fixed for PMSAv8 only */ +#define PMSAv8_XIP_REGION 0 +#define PMSAv8_KERNEL_REGION 1 /* Maximum number of regions Linux is interested in */ -#define MPU_MAX_REGIONS 16 +#define MPU_MAX_REGIONS 16 -#define MPU_DATA_SIDE 0 -#define MPU_INSTR_SIDE 1 +#define PMSAv7_DATA_SIDE 0 +#define PMSAv7_INSTR_SIDE 1 #ifndef __ASSEMBLY__ struct mpu_rgn { /* Assume same attributes for d/i-side */ - u32 drbar; - u32 drsr; - u32 dracr; + union { + u32 drbar; /* PMSAv7 */ + u32 prbar; /* PMSAv8 */ + }; + union { + u32 drsr; /* PMSAv7 */ + u32 prlar; /* PMSAv8 */ + }; + union { + u32 dracr; /* PMSAv7 */ + u32 unused; /* not used in PMSAv8 */ + }; }; struct mpu_rgn_info { @@ -75,16 +116,17 @@ struct mpu_rgn_info { extern struct mpu_rgn_info mpu_rgn_info; #ifdef CONFIG_ARM_MPU +extern void __init pmsav7_adjust_lowmem_bounds(void); +extern void __init pmsav8_adjust_lowmem_bounds(void); -extern void __init adjust_lowmem_bounds_mpu(void); -extern void __init mpu_setup(void); - +extern void __init pmsav7_setup(void); +extern void __init pmsav8_setup(void); #else - -static inline void adjust_lowmem_bounds_mpu(void) {} -static inline void mpu_setup(void) {} - -#endif /* !CONFIG_ARM_MPU */ +static inline void pmsav7_adjust_lowmem_bounds(void) {}; +static inline void pmsav8_adjust_lowmem_bounds(void) {}; +static inline void pmsav7_setup(void) {}; +static inline void pmsav8_setup(void) {}; +#endif #endif /* __ASSEMBLY__ */ diff --git a/arch/arm/include/asm/pci.h b/arch/arm/include/asm/pci.h index 1f0de808d111..0abd389cf0ec 100644 --- a/arch/arm/include/asm/pci.h +++ b/arch/arm/include/asm/pci.h @@ -19,13 +19,6 @@ static inline int pci_proc_domain(struct pci_bus *bus) } #endif /* CONFIG_PCI_DOMAINS */ -/* - * The PCI address space does equal the physical memory address space. - * The networking and block device layers use this boolean for bounce - * buffer decisions. - */ -#define PCI_DMA_BUS_IS_PHYS (1) - #define HAVE_PCI_MMAP #define ARCH_GENERIC_PCI_MMAP_RESOURCE diff --git a/arch/arm/include/asm/pgtable-3level.h b/arch/arm/include/asm/pgtable-3level.h index 2a4836087358..6d50a11d7793 100644 --- a/arch/arm/include/asm/pgtable-3level.h +++ b/arch/arm/include/asm/pgtable-3level.h @@ -219,7 +219,6 @@ static inline pte_t pte_mkspecial(pte_t pte) pte_val(pte) |= L_PTE_SPECIAL; return pte; } -#define __HAVE_ARCH_PTE_SPECIAL #define pmd_write(pmd) (pmd_isclear((pmd), L_PMD_SECT_RDONLY)) #define pmd_dirty(pmd) (pmd_isset((pmd), L_PMD_SECT_DIRTY)) diff --git a/arch/arm/include/asm/proc-fns.h b/arch/arm/include/asm/proc-fns.h index f2e1af45bd6f..e25f4392e1b2 100644 --- a/arch/arm/include/asm/proc-fns.h +++ b/arch/arm/include/asm/proc-fns.h @@ -37,6 +37,10 @@ extern struct processor { */ void (*_proc_init)(void); /* + * Check for processor bugs + */ + void (*check_bugs)(void); + /* * Disable any processor specifics */ void (*_proc_fin)(void); diff --git a/arch/arm/include/asm/secure_cntvoff.h b/arch/arm/include/asm/secure_cntvoff.h new file mode 100644 index 000000000000..1f93aee1f630 --- /dev/null +++ b/arch/arm/include/asm/secure_cntvoff.h @@ -0,0 +1,8 @@ +/* SPDX-License-Identifier: GPL-2.0 */ + +#ifndef __ASMARM_ARCH_CNTVOFF_H +#define __ASMARM_ARCH_CNTVOFF_H + +extern void secure_cntvoff_init(void); + +#endif diff --git a/arch/arm/include/asm/system_misc.h b/arch/arm/include/asm/system_misc.h index 78f6db114faf..8e76db83c498 100644 --- a/arch/arm/include/asm/system_misc.h +++ b/arch/arm/include/asm/system_misc.h @@ -8,6 +8,7 @@ #include <linux/linkage.h> #include <linux/irqflags.h> #include <linux/reboot.h> +#include <linux/percpu.h> extern void cpu_init(void); @@ -15,6 +16,20 @@ void soft_restart(unsigned long); extern void (*arm_pm_restart)(enum reboot_mode reboot_mode, const char *cmd); extern void (*arm_pm_idle)(void); +#ifdef CONFIG_HARDEN_BRANCH_PREDICTOR +typedef void (*harden_branch_predictor_fn_t)(void); +DECLARE_PER_CPU(harden_branch_predictor_fn_t, harden_branch_predictor_fn); +static inline void harden_branch_predictor(void) +{ + harden_branch_predictor_fn_t fn = per_cpu(harden_branch_predictor_fn, + smp_processor_id()); + if (fn) + fn(); +} +#else +#define harden_branch_predictor() do { } while (0) +#endif + #define UDBG_UNDEFINED (1 << 0) #define UDBG_SYSCALL (1 << 1) #define UDBG_BADABORT (1 << 2) diff --git a/arch/arm/include/asm/uaccess.h b/arch/arm/include/asm/uaccess.h index 0bf2347495f1..3d614e90c19f 100644 --- a/arch/arm/include/asm/uaccess.h +++ b/arch/arm/include/asm/uaccess.h @@ -152,7 +152,7 @@ extern int __get_user_64t_4(void *); #define __get_user_check(x, p) \ ({ \ unsigned long __limit = current_thread_info()->addr_limit - 1; \ - register const typeof(*(p)) __user *__p asm("r0") = (p);\ + register typeof(*(p)) __user *__p asm("r0") = (p); \ register typeof(x) __r2 asm("r2"); \ register unsigned long __l asm("r1") = __limit; \ register int __e asm("r0"); \ diff --git a/arch/arm/include/asm/v7m.h b/arch/arm/include/asm/v7m.h index 634e77107425..187ccf6496ad 100644 --- a/arch/arm/include/asm/v7m.h +++ b/arch/arm/include/asm/v7m.h @@ -64,9 +64,17 @@ #define MPU_CTRL_ENABLE 1 #define MPU_CTRL_PRIVDEFENA (1 << 2) -#define MPU_RNR 0x98 -#define MPU_RBAR 0x9c -#define MPU_RASR 0xa0 +#define PMSAv7_RNR 0x98 +#define PMSAv7_RBAR 0x9c +#define PMSAv7_RASR 0xa0 + +#define PMSAv8_RNR 0x98 +#define PMSAv8_RBAR 0x9c +#define PMSAv8_RLAR 0xa0 +#define PMSAv8_RBAR_A(n) (PMSAv8_RBAR + 8*(n)) +#define PMSAv8_RLAR_A(n) (PMSAv8_RLAR + 8*(n)) +#define PMSAv8_MAIR0 0xc0 +#define PMSAv8_MAIR1 0xc4 /* Cache opeartions */ #define V7M_SCB_ICIALLU 0x250 /* I-cache invalidate all to PoU */ diff --git a/arch/arm/include/debug/brcmstb.S b/arch/arm/include/debug/brcmstb.S index c826f15d2f80..0f580caa81e5 100644 --- a/arch/arm/include/debug/brcmstb.S +++ b/arch/arm/include/debug/brcmstb.S @@ -11,20 +11,25 @@ * GNU General Public License for more details. */ #include <linux/serial_reg.h> +#include <asm/cputype.h> /* Physical register offset and virtual register offset */ #define REG_PHYS_BASE 0xf0000000 +#define REG_PHYS_BASE_V7 0x08000000 #define REG_VIRT_BASE 0xfc000000 #define REG_PHYS_ADDR(x) ((x) + REG_PHYS_BASE) +#define REG_PHYS_ADDR_V7(x) ((x) + REG_PHYS_BASE_V7) /* Product id can be read from here */ #define SUN_TOP_CTRL_BASE REG_PHYS_ADDR(0x404000) +#define SUN_TOP_CTRL_BASE_V7 REG_PHYS_ADDR_V7(0x404000) #define UARTA_3390 REG_PHYS_ADDR(0x40a900) #define UARTA_7250 REG_PHYS_ADDR(0x40b400) #define UARTA_7260 REG_PHYS_ADDR(0x40c000) #define UARTA_7268 UARTA_7260 #define UARTA_7271 UARTA_7268 +#define UARTA_7278 REG_PHYS_ADDR_V7(0x40c000) #define UARTA_7364 REG_PHYS_ADDR(0x40b000) #define UARTA_7366 UARTA_7364 #define UARTA_74371 REG_PHYS_ADDR(0x406b00) @@ -55,8 +60,21 @@ mov \rv, #0 @ yes; record init is done str \rv, [\tmp] + /* Check for V7 memory map if B53 */ + mrc p15, 0, \rv, c0, c0, 0 @ get Main ID register + ldr \rp, =ARM_CPU_PART_MASK + and \rv, \rv, \rp + ldr \rp, =ARM_CPU_PART_BRAHMA_B53 @ check for B53 CPU + cmp \rv, \rp + bne 10f + + /* if PERIPHBASE doesn't overlap REG_PHYS_BASE use V7 map */ + mrc p15, 1, \rv, c15, c3, 0 @ get PERIPHBASE from CBAR + ands \rv, \rv, #REG_PHYS_BASE + ldreq \rp, =SUN_TOP_CTRL_BASE_V7 + /* Check SUN_TOP_CTRL base */ - ldr \rp, =SUN_TOP_CTRL_BASE @ load SUN_TOP_CTRL PA +10: ldrne \rp, =SUN_TOP_CTRL_BASE @ load SUN_TOP_CTRL PA ldr \rv, [\rp, #0] @ get register contents ARM_BE8( rev \rv, \rv ) and \rv, \rv, #0xffffff00 @ strip revision bits [7:0] @@ -72,6 +90,7 @@ ARM_BE8( rev \rv, \rv ) 27: checkuart(\rp, \rv, 0x07437100, 74371) 28: checkuart(\rp, \rv, 0x74390000, 7439) 29: checkuart(\rp, \rv, 0x74450000, 7445) +30: checkuart(\rp, \rv, 0x72780000, 7278) /* No valid UART found */ 90: mov \rp, #0 diff --git a/arch/arm/include/uapi/asm/kvm.h b/arch/arm/include/uapi/asm/kvm.h index caae4843cb70..16e006f708ca 100644 --- a/arch/arm/include/uapi/asm/kvm.h +++ b/arch/arm/include/uapi/asm/kvm.h @@ -91,6 +91,7 @@ struct kvm_regs { #define KVM_VGIC_V3_ADDR_TYPE_DIST 2 #define KVM_VGIC_V3_ADDR_TYPE_REDIST 3 #define KVM_VGIC_ITS_ADDR_TYPE 4 +#define KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION 5 #define KVM_VGIC_V3_DIST_SIZE SZ_64K #define KVM_VGIC_V3_REDIST_SIZE (2 * SZ_64K) diff --git a/arch/arm/include/uapi/asm/siginfo.h b/arch/arm/include/uapi/asm/siginfo.h deleted file mode 100644 index d0513880be21..000000000000 --- a/arch/arm/include/uapi/asm/siginfo.h +++ /dev/null @@ -1,13 +0,0 @@ -#ifndef __ASM_SIGINFO_H -#define __ASM_SIGINFO_H - -#include <asm-generic/siginfo.h> - -/* - * SIGFPE si_codes - */ -#ifdef __KERNEL__ -#define FPE_FIXME 0 /* Broken dup of SI_USER */ -#endif /* __KERNEL__ */ - -#endif diff --git a/arch/arm/kernel/Makefile b/arch/arm/kernel/Makefile index b59ac4bf82b8..8cad59465af3 100644 --- a/arch/arm/kernel/Makefile +++ b/arch/arm/kernel/Makefile @@ -31,6 +31,7 @@ else obj-y += entry-armv.o endif +obj-$(CONFIG_MMU) += bugs.o obj-$(CONFIG_CPU_IDLE) += cpuidle.o obj-$(CONFIG_ISA_DMA_API) += dma.o obj-$(CONFIG_FIQ) += fiq.o fiqasm.o diff --git a/arch/arm/kernel/asm-offsets.c b/arch/arm/kernel/asm-offsets.c index f369ece99958..974d8d7d1bcd 100644 --- a/arch/arm/kernel/asm-offsets.c +++ b/arch/arm/kernel/asm-offsets.c @@ -61,7 +61,7 @@ int main(void) { DEFINE(TSK_ACTIVE_MM, offsetof(struct task_struct, active_mm)); -#ifdef CONFIG_CC_STACKPROTECTOR +#ifdef CONFIG_STACKPROTECTOR DEFINE(TSK_STACK_CANARY, offsetof(struct task_struct, stack_canary)); #endif BLANK(); @@ -194,9 +194,11 @@ int main(void) DEFINE(MPU_RNG_INFO_USED, offsetof(struct mpu_rgn_info, used)); DEFINE(MPU_RNG_SIZE, sizeof(struct mpu_rgn)); - DEFINE(MPU_RGN_DRBAR, offsetof(struct mpu_rgn, drbar)); - DEFINE(MPU_RGN_DRSR, offsetof(struct mpu_rgn, drsr)); - DEFINE(MPU_RGN_DRACR, offsetof(struct mpu_rgn, dracr)); + DEFINE(MPU_RGN_DRBAR, offsetof(struct mpu_rgn, drbar)); + DEFINE(MPU_RGN_DRSR, offsetof(struct mpu_rgn, drsr)); + DEFINE(MPU_RGN_DRACR, offsetof(struct mpu_rgn, dracr)); + DEFINE(MPU_RGN_PRBAR, offsetof(struct mpu_rgn, prbar)); + DEFINE(MPU_RGN_PRLAR, offsetof(struct mpu_rgn, prlar)); #endif return 0; } diff --git a/arch/arm/kernel/bugs.c b/arch/arm/kernel/bugs.c new file mode 100644 index 000000000000..7be511310191 --- /dev/null +++ b/arch/arm/kernel/bugs.c @@ -0,0 +1,18 @@ +// SPDX-Identifier: GPL-2.0 +#include <linux/init.h> +#include <asm/bugs.h> +#include <asm/proc-fns.h> + +void check_other_bugs(void) +{ +#ifdef MULTI_CPU + if (processor.check_bugs) + processor.check_bugs(); +#endif +} + +void __init check_bugs(void) +{ + check_writebuffer_bugs(); + check_other_bugs(); +} diff --git a/arch/arm/kernel/dma.c b/arch/arm/kernel/dma.c index e651c4d0a0d9..6739d37c2bc5 100644 --- a/arch/arm/kernel/dma.c +++ b/arch/arm/kernel/dma.c @@ -276,21 +276,9 @@ static int proc_dma_show(struct seq_file *m, void *v) return 0; } -static int proc_dma_open(struct inode *inode, struct file *file) -{ - return single_open(file, proc_dma_show, NULL); -} - -static const struct file_operations proc_dma_operations = { - .open = proc_dma_open, - .read = seq_read, - .llseek = seq_lseek, - .release = single_release, -}; - static int __init proc_dma_init(void) { - proc_create("dma", 0, NULL, &proc_dma_operations); + proc_create_single("dma", 0, NULL, proc_dma_show); return 0; } diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S index 1752033b0070..179a9f6bd1e3 100644 --- a/arch/arm/kernel/entry-armv.S +++ b/arch/arm/kernel/entry-armv.S @@ -791,7 +791,7 @@ ENTRY(__switch_to) ldr r6, [r2, #TI_CPU_DOMAIN] #endif switch_tls r1, r4, r5, r3, r7 -#if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP) +#if defined(CONFIG_STACKPROTECTOR) && !defined(CONFIG_SMP) ldr r7, [r2, #TI_TASK] ldr r8, =__stack_chk_guard .if (TSK_STACK_CANARY > IMM12_MASK) @@ -807,7 +807,7 @@ ENTRY(__switch_to) ldr r0, =thread_notify_head mov r1, #THREAD_NOTIFY_SWITCH bl atomic_notifier_call_chain -#if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP) +#if defined(CONFIG_STACKPROTECTOR) && !defined(CONFIG_SMP) str r7, [r8] #endif THUMB( mov ip, r4 ) diff --git a/arch/arm/kernel/entry-common.S b/arch/arm/kernel/entry-common.S index 3c4f88701f22..106a1466518d 100644 --- a/arch/arm/kernel/entry-common.S +++ b/arch/arm/kernel/entry-common.S @@ -39,12 +39,13 @@ saved_pc .req lr .section .entry.text,"ax",%progbits .align 5 -#if !(IS_ENABLED(CONFIG_TRACE_IRQFLAGS) || IS_ENABLED(CONFIG_CONTEXT_TRACKING)) +#if !(IS_ENABLED(CONFIG_TRACE_IRQFLAGS) || IS_ENABLED(CONFIG_CONTEXT_TRACKING) || \ + IS_ENABLED(CONFIG_DEBUG_RSEQ)) /* * This is the fast syscall return path. We do as little as possible here, * such as avoiding writing r0 to the stack. We only use this path if we - * have tracing and context tracking disabled - the overheads from those - * features make this path too inefficient. + * have tracing, context tracking and rseq debug disabled - the overheads + * from those features make this path too inefficient. */ ret_fast_syscall: UNWIND(.fnstart ) @@ -71,14 +72,20 @@ fast_work_pending: /* fall through to work_pending */ #else /* - * The "replacement" ret_fast_syscall for when tracing or context tracking - * is enabled. As we will need to call out to some C functions, we save - * r0 first to avoid needing to save registers around each C function call. + * The "replacement" ret_fast_syscall for when tracing, context tracking, + * or rseq debug is enabled. As we will need to call out to some C functions, + * we save r0 first to avoid needing to save registers around each C function + * call. */ ret_fast_syscall: UNWIND(.fnstart ) UNWIND(.cantunwind ) str r0, [sp, #S_R0 + S_OFF]! @ save returned r0 +#if IS_ENABLED(CONFIG_DEBUG_RSEQ) + /* do_rseq_syscall needs interrupts enabled. */ + mov r0, sp @ 'regs' + bl do_rseq_syscall +#endif disable_irq_notrace @ disable interrupts ldr r2, [tsk, #TI_ADDR_LIMIT] cmp r2, #TASK_SIZE @@ -113,6 +120,12 @@ ENDPROC(ret_fast_syscall) */ ENTRY(ret_to_user) ret_slow_syscall: +#if IS_ENABLED(CONFIG_DEBUG_RSEQ) + /* do_rseq_syscall needs interrupts enabled. */ + enable_irq_notrace @ enable interrupts + mov r0, sp @ 'regs' + bl do_rseq_syscall +#endif disable_irq_notrace @ disable interrupts ENTRY(ret_to_user_from_irq) ldr r2, [tsk, #TI_ADDR_LIMIT] @@ -242,9 +255,7 @@ local_restart: tst r10, #_TIF_SYSCALL_WORK @ are we tracing syscalls? bne __sys_trace - cmp scno, #NR_syscalls @ check upper syscall limit - badr lr, ret_fast_syscall @ return address - ldrcc pc, [tbl, scno, lsl #2] @ call sys_* routine + invoke_syscall tbl, scno, r10, ret_fast_syscall add r1, sp, #S_OFF 2: cmp scno, #(__ARM_NR_BASE - __NR_SYSCALL_BASE) @@ -278,14 +289,8 @@ __sys_trace: mov r1, scno add r0, sp, #S_OFF bl syscall_trace_enter - - badr lr, __sys_trace_return @ return address - mov scno, r0 @ syscall number (possibly new) - add r1, sp, #S_R0 + S_OFF @ pointer to regs - cmp scno, #NR_syscalls @ check upper syscall limit - ldmccia r1, {r0 - r6} @ have to reload r0 - r6 - stmccia sp, {r4, r5} @ and update the stack args - ldrcc pc, [tbl, scno, lsl #2] @ call sys_* routine + mov scno, r0 + invoke_syscall tbl, scno, r10, __sys_trace_return, reload=1 cmp scno, #-1 @ skip the syscall? bne 2b add sp, sp, #S_OFF @ restore stack @@ -363,6 +368,10 @@ sys_syscall: bic scno, r0, #__NR_OABI_SYSCALL_BASE cmp scno, #__NR_syscall - __NR_SYSCALL_BASE cmpne scno, #NR_syscalls @ check range +#ifdef CONFIG_CPU_SPECTRE + movhs scno, #0 + csdb +#endif stmloia sp, {r5, r6} @ shuffle args movlo r0, r1 movlo r1, r2 diff --git a/arch/arm/kernel/entry-header.S b/arch/arm/kernel/entry-header.S index 0f07579af472..773424843d6e 100644 --- a/arch/arm/kernel/entry-header.S +++ b/arch/arm/kernel/entry-header.S @@ -378,6 +378,31 @@ #endif .endm + .macro invoke_syscall, table, nr, tmp, ret, reload=0 +#ifdef CONFIG_CPU_SPECTRE + mov \tmp, \nr + cmp \tmp, #NR_syscalls @ check upper syscall limit + movcs \tmp, #0 + csdb + badr lr, \ret @ return address + .if \reload + add r1, sp, #S_R0 + S_OFF @ pointer to regs + ldmccia r1, {r0 - r6} @ reload r0-r6 + stmccia sp, {r4, r5} @ update stack arguments + .endif + ldrcc pc, [\table, \tmp, lsl #2] @ call sys_* routine +#else + cmp \nr, #NR_syscalls @ check upper syscall limit + badr lr, \ret @ return address + .if \reload + add r1, sp, #S_R0 + S_OFF @ pointer to regs + ldmccia r1, {r0 - r6} @ reload r0-r6 + stmccia sp, {r4, r5} @ update stack arguments + .endif + ldrcc pc, [\table, \nr, lsl #2] @ call sys_* routine +#endif + .endm + /* * These are the registers used in the syscall handler, and allow us to * have in theory up to 7 arguments to a function - r0 to r6. diff --git a/arch/arm/kernel/head-nommu.S b/arch/arm/kernel/head-nommu.S index 2e38f85b757a..dd546d65a383 100644 --- a/arch/arm/kernel/head-nommu.S +++ b/arch/arm/kernel/head-nommu.S @@ -68,14 +68,6 @@ ENTRY(stext) beq __error_p @ yes, error 'p' #ifdef CONFIG_ARM_MPU - /* Calculate the size of a region covering just the kernel */ - ldr r5, =PLAT_PHYS_OFFSET @ Region start: PHYS_OFFSET - ldr r6, =(_end) @ Cover whole kernel - sub r6, r6, r5 @ Minimum size of region to map - clz r6, r6 @ Region size must be 2^N... - rsb r6, r6, #31 @ ...so round up region size - lsl r6, r6, #MPU_RSR_SZ @ Put size in right field - orr r6, r6, #(1 << MPU_RSR_EN) @ Set region enabled bit bl __setup_mpu #endif @@ -83,8 +75,8 @@ ENTRY(stext) ldr r12, [r10, #PROCINFO_INITFUNC] add r12, r12, r10 ret r12 -1: bl __after_proc_init - b __mmap_switched +1: ldr lr, =__mmap_switched + b __after_proc_init ENDPROC(stext) #ifdef CONFIG_SMP @@ -110,8 +102,6 @@ ENTRY(secondary_startup) ldr r7, __secondary_data #ifdef CONFIG_ARM_MPU - /* Use MPU region info supplied by __cpu_up */ - ldr r6, [r7] @ get secondary_data.mpu_rgn_info bl __secondary_setup_mpu @ Initialize the MPU #endif @@ -133,12 +123,45 @@ __secondary_data: /* * Set the Control Register and Read the process ID. */ + .text __after_proc_init: +#ifdef CONFIG_ARM_MPU +M_CLASS(movw r12, #:lower16:BASEADDR_V7M_SCB) +M_CLASS(movt r12, #:upper16:BASEADDR_V7M_SCB) +M_CLASS(ldr r3, [r12, 0x50]) +AR_CLASS(mrc p15, 0, r3, c0, c1, 4) @ Read ID_MMFR0 + and r3, r3, #(MMFR0_PMSA) @ PMSA field + teq r3, #(MMFR0_PMSAv7) @ PMSA v7 + beq 1f + teq r3, #(MMFR0_PMSAv8) @ PMSA v8 + /* + * Memory region attributes for PMSAv8: + * + * n = AttrIndx[2:0] + * n MAIR + * DEVICE_nGnRnE 000 00000000 + * NORMAL 001 11111111 + */ + ldreq r3, =PMSAv8_MAIR(0x00, PMSAv8_RGN_DEVICE_nGnRnE) | \ + PMSAv8_MAIR(0xff, PMSAv8_RGN_NORMAL) +AR_CLASS(mcreq p15, 0, r3, c10, c2, 0) @ MAIR 0 +M_CLASS(streq r3, [r12, #PMSAv8_MAIR0]) + moveq r3, #0 +AR_CLASS(mcreq p15, 0, r3, c10, c2, 1) @ MAIR 1 +M_CLASS(streq r3, [r12, #PMSAv8_MAIR1]) + +1: +#endif #ifdef CONFIG_CPU_CP15 /* * CP15 system control register value returned in r0 from * the CPU init function. */ + +#ifdef CONFIG_ARM_MPU + biceq r0, r0, #CR_BR @ Disable the 'default mem-map' + orreq r0, r0, #CR_M @ Set SCTRL.M (MPU on) +#endif #if defined(CONFIG_ALIGNMENT_TRAP) && __LINUX_ARM_ARCH__ < 6 orr r0, r0, #CR_A #else @@ -154,7 +177,15 @@ __after_proc_init: bic r0, r0, #CR_I #endif mcr p15, 0, r0, c1, c0, 0 @ write control reg + isb #elif defined (CONFIG_CPU_V7M) +#ifdef CONFIG_ARM_MPU + ldreq r3, [r12, MPU_CTRL] + biceq r3, #MPU_CTRL_PRIVDEFENA + orreq r3, #MPU_CTRL_ENABLE + streq r3, [r12, MPU_CTRL] + isb +#endif /* For V7M systems we want to modify the CCR similarly to the SCTLR */ #ifdef CONFIG_CPU_DCACHE_DISABLE bic r0, r0, #V7M_SCB_CCR_DC @@ -165,9 +196,7 @@ __after_proc_init: #ifdef CONFIG_CPU_ICACHE_DISABLE bic r0, r0, #V7M_SCB_CCR_IC #endif - movw r3, #:lower16:(BASEADDR_V7M_SCB + V7M_SCB_CCR) - movt r3, #:upper16:(BASEADDR_V7M_SCB + V7M_SCB_CCR) - str r0, [r3] + str r0, [r12, V7M_SCB_CCR] #endif /* CONFIG_CPU_CP15 elif CONFIG_CPU_V7M */ ret lr ENDPROC(__after_proc_init) @@ -184,7 +213,7 @@ ENDPROC(__after_proc_init) .endm /* Setup a single MPU region, either D or I side (D-side for unified) */ -.macro setup_region bar, acr, sr, side = MPU_DATA_SIDE, unused +.macro setup_region bar, acr, sr, side = PMSAv7_DATA_SIDE, unused mcr p15, 0, \bar, c6, c1, (0 + \side) @ I/DRBAR mcr p15, 0, \acr, c6, c1, (4 + \side) @ I/DRACR mcr p15, 0, \sr, c6, c1, (2 + \side) @ I/DRSR @@ -192,14 +221,14 @@ ENDPROC(__after_proc_init) #else .macro set_region_nr tmp, rgnr, base mov \tmp, \rgnr - str \tmp, [\base, #MPU_RNR] + str \tmp, [\base, #PMSAv7_RNR] .endm .macro setup_region bar, acr, sr, unused, base lsl \acr, \acr, #16 orr \acr, \acr, \sr - str \bar, [\base, #MPU_RBAR] - str \acr, [\base, #MPU_RASR] + str \bar, [\base, #PMSAv7_RBAR] + str \acr, [\base, #PMSAv7_RASR] .endm #endif @@ -210,8 +239,9 @@ ENDPROC(__after_proc_init) * Region 2: Normal, Shared, cacheable for RAM. From PHYS_OFFSET, size from r6 * Region 3: Normal, shared, inaccessible from PL0 to protect the vectors page * - * r6: Value to be written to DRSR (and IRSR if required) for MPU_RAM_REGION + * r6: Value to be written to DRSR (and IRSR if required) for PMSAv7_RAM_REGION */ + __HEAD ENTRY(__setup_mpu) @@ -223,7 +253,22 @@ AR_CLASS(mrc p15, 0, r0, c0, c1, 4) @ Read ID_MMFR0 M_CLASS(ldr r0, [r12, 0x50]) and r0, r0, #(MMFR0_PMSA) @ PMSA field teq r0, #(MMFR0_PMSAv7) @ PMSA v7 - bxne lr + beq __setup_pmsa_v7 + teq r0, #(MMFR0_PMSAv8) @ PMSA v8 + beq __setup_pmsa_v8 + + ret lr +ENDPROC(__setup_mpu) + +ENTRY(__setup_pmsa_v7) + /* Calculate the size of a region covering just the kernel */ + ldr r5, =PLAT_PHYS_OFFSET @ Region start: PHYS_OFFSET + ldr r6, =(_end) @ Cover whole kernel + sub r6, r6, r5 @ Minimum size of region to map + clz r6, r6 @ Region size must be 2^N... + rsb r6, r6, #31 @ ...so round up region size + lsl r6, r6, #PMSAv7_RSR_SZ @ Put size in right field + orr r6, r6, #(1 << PMSAv7_RSR_EN) @ Set region enabled bit /* Determine whether the D/I-side memory map is unified. We set the * flags here and continue to use them for the rest of this function */ @@ -234,77 +279,189 @@ M_CLASS(ldr r0, [r12, #MPU_TYPE]) tst r0, #MPUIR_nU @ MPUIR_nU = 0 for unified /* Setup second region first to free up r6 */ - set_region_nr r0, #MPU_RAM_REGION, r12 + set_region_nr r0, #PMSAv7_RAM_REGION, r12 isb /* Full access from PL0, PL1, shared for CONFIG_SMP, cacheable */ ldr r0, =PLAT_PHYS_OFFSET @ RAM starts at PHYS_OFFSET - ldr r5,=(MPU_AP_PL1RW_PL0RW | MPU_RGN_NORMAL) + ldr r5,=(PMSAv7_AP_PL1RW_PL0RW | PMSAv7_RGN_NORMAL) - setup_region r0, r5, r6, MPU_DATA_SIDE, r12 @ PHYS_OFFSET, shared, enabled + setup_region r0, r5, r6, PMSAv7_DATA_SIDE, r12 @ PHYS_OFFSET, shared, enabled beq 1f @ Memory-map not unified - setup_region r0, r5, r6, MPU_INSTR_SIDE, r12 @ PHYS_OFFSET, shared, enabled + setup_region r0, r5, r6, PMSAv7_INSTR_SIDE, r12 @ PHYS_OFFSET, shared, enabled 1: isb /* First/background region */ - set_region_nr r0, #MPU_BG_REGION, r12 + set_region_nr r0, #PMSAv7_BG_REGION, r12 isb /* Execute Never, strongly ordered, inaccessible to PL0, rw PL1 */ mov r0, #0 @ BG region starts at 0x0 - ldr r5,=(MPU_ACR_XN | MPU_RGN_STRONGLY_ORDERED | MPU_AP_PL1RW_PL0NA) - mov r6, #MPU_RSR_ALL_MEM @ 4GB region, enabled + ldr r5,=(PMSAv7_ACR_XN | PMSAv7_RGN_STRONGLY_ORDERED | PMSAv7_AP_PL1RW_PL0NA) + mov r6, #PMSAv7_RSR_ALL_MEM @ 4GB region, enabled - setup_region r0, r5, r6, MPU_DATA_SIDE, r12 @ 0x0, BG region, enabled + setup_region r0, r5, r6, PMSAv7_DATA_SIDE, r12 @ 0x0, BG region, enabled beq 2f @ Memory-map not unified - setup_region r0, r5, r6, MPU_INSTR_SIDE r12 @ 0x0, BG region, enabled + setup_region r0, r5, r6, PMSAv7_INSTR_SIDE r12 @ 0x0, BG region, enabled 2: isb #ifdef CONFIG_XIP_KERNEL - set_region_nr r0, #MPU_ROM_REGION, r12 + set_region_nr r0, #PMSAv7_ROM_REGION, r12 isb - ldr r5,=(MPU_AP_PL1RO_PL0NA | MPU_RGN_NORMAL) + ldr r5,=(PMSAv7_AP_PL1RO_PL0NA | PMSAv7_RGN_NORMAL) ldr r0, =CONFIG_XIP_PHYS_ADDR @ ROM start ldr r6, =(_exiprom) @ ROM end sub r6, r6, r0 @ Minimum size of region to map clz r6, r6 @ Region size must be 2^N... rsb r6, r6, #31 @ ...so round up region size - lsl r6, r6, #MPU_RSR_SZ @ Put size in right field - orr r6, r6, #(1 << MPU_RSR_EN) @ Set region enabled bit + lsl r6, r6, #PMSAv7_RSR_SZ @ Put size in right field + orr r6, r6, #(1 << PMSAv7_RSR_EN) @ Set region enabled bit - setup_region r0, r5, r6, MPU_DATA_SIDE, r12 @ XIP_PHYS_ADDR, shared, enabled + setup_region r0, r5, r6, PMSAv7_DATA_SIDE, r12 @ XIP_PHYS_ADDR, shared, enabled beq 3f @ Memory-map not unified - setup_region r0, r5, r6, MPU_INSTR_SIDE, r12 @ XIP_PHYS_ADDR, shared, enabled + setup_region r0, r5, r6, PMSAv7_INSTR_SIDE, r12 @ XIP_PHYS_ADDR, shared, enabled 3: isb #endif + ret lr +ENDPROC(__setup_pmsa_v7) + +ENTRY(__setup_pmsa_v8) + mov r0, #0 +AR_CLASS(mcr p15, 0, r0, c6, c2, 1) @ PRSEL +M_CLASS(str r0, [r12, #PMSAv8_RNR]) + isb + +#ifdef CONFIG_XIP_KERNEL + ldr r5, =CONFIG_XIP_PHYS_ADDR @ ROM start + ldr r6, =(_exiprom) @ ROM end + sub r6, r6, #1 + bic r6, r6, #(PMSAv8_MINALIGN - 1) + + orr r5, r5, #(PMSAv8_AP_PL1RW_PL0NA | PMSAv8_RGN_SHARED) + orr r6, r6, #(PMSAv8_LAR_IDX(PMSAv8_RGN_NORMAL) | PMSAv8_LAR_EN) + +AR_CLASS(mcr p15, 0, r5, c6, c8, 0) @ PRBAR0 +AR_CLASS(mcr p15, 0, r6, c6, c8, 1) @ PRLAR0 +M_CLASS(str r5, [r12, #PMSAv8_RBAR_A(0)]) +M_CLASS(str r6, [r12, #PMSAv8_RLAR_A(0)]) +#endif + + ldr r5, =KERNEL_START + ldr r6, =KERNEL_END + sub r6, r6, #1 + bic r6, r6, #(PMSAv8_MINALIGN - 1) + + orr r5, r5, #(PMSAv8_AP_PL1RW_PL0NA | PMSAv8_RGN_SHARED) + orr r6, r6, #(PMSAv8_LAR_IDX(PMSAv8_RGN_NORMAL) | PMSAv8_LAR_EN) + +AR_CLASS(mcr p15, 0, r5, c6, c8, 4) @ PRBAR1 +AR_CLASS(mcr p15, 0, r6, c6, c8, 5) @ PRLAR1 +M_CLASS(str r5, [r12, #PMSAv8_RBAR_A(1)]) +M_CLASS(str r6, [r12, #PMSAv8_RLAR_A(1)]) + + /* Setup Background: 0x0 - min(KERNEL_START, XIP_PHYS_ADDR) */ +#ifdef CONFIG_XIP_KERNEL + ldr r6, =KERNEL_START + ldr r5, =CONFIG_XIP_PHYS_ADDR + cmp r6, r5 + movcs r6, r5 +#else + ldr r6, =KERNEL_START +#endif + cmp r6, #0 + beq 1f + + mov r5, #0 + sub r6, r6, #1 + bic r6, r6, #(PMSAv8_MINALIGN - 1) + + orr r5, r5, #(PMSAv8_AP_PL1RW_PL0NA | PMSAv8_RGN_SHARED | PMSAv8_BAR_XN) + orr r6, r6, #(PMSAv8_LAR_IDX(PMSAv8_RGN_DEVICE_nGnRnE) | PMSAv8_LAR_EN) + +AR_CLASS(mcr p15, 0, r5, c6, c9, 0) @ PRBAR2 +AR_CLASS(mcr p15, 0, r6, c6, c9, 1) @ PRLAR2 +M_CLASS(str r5, [r12, #PMSAv8_RBAR_A(2)]) +M_CLASS(str r6, [r12, #PMSAv8_RLAR_A(2)]) + +1: + /* Setup Background: max(KERNEL_END, _exiprom) - 0xffffffff */ +#ifdef CONFIG_XIP_KERNEL + ldr r5, =KERNEL_END + ldr r6, =(_exiprom) + cmp r5, r6 + movcc r5, r6 +#else + ldr r5, =KERNEL_END +#endif + mov r6, #0xffffffff + bic r6, r6, #(PMSAv8_MINALIGN - 1) + + orr r5, r5, #(PMSAv8_AP_PL1RW_PL0NA | PMSAv8_RGN_SHARED | PMSAv8_BAR_XN) + orr r6, r6, #(PMSAv8_LAR_IDX(PMSAv8_RGN_DEVICE_nGnRnE) | PMSAv8_LAR_EN) - /* Enable the MPU */ -AR_CLASS(mrc p15, 0, r0, c1, c0, 0) @ Read SCTLR -AR_CLASS(bic r0, r0, #CR_BR) @ Disable the 'default mem-map' -AR_CLASS(orr r0, r0, #CR_M) @ Set SCTRL.M (MPU on) -AR_CLASS(mcr p15, 0, r0, c1, c0, 0) @ Enable MPU +AR_CLASS(mcr p15, 0, r5, c6, c9, 4) @ PRBAR3 +AR_CLASS(mcr p15, 0, r6, c6, c9, 5) @ PRLAR3 +M_CLASS(str r5, [r12, #PMSAv8_RBAR_A(3)]) +M_CLASS(str r6, [r12, #PMSAv8_RLAR_A(3)]) -M_CLASS(ldr r0, [r12, #MPU_CTRL]) -M_CLASS(bic r0, #MPU_CTRL_PRIVDEFENA) -M_CLASS(orr r0, #MPU_CTRL_ENABLE) -M_CLASS(str r0, [r12, #MPU_CTRL]) +#ifdef CONFIG_XIP_KERNEL + /* Setup Background: min(_exiprom, KERNEL_END) - max(KERNEL_START, XIP_PHYS_ADDR) */ + ldr r5, =(_exiprom) + ldr r6, =KERNEL_END + cmp r5, r6 + movcs r5, r6 + + ldr r6, =KERNEL_START + ldr r0, =CONFIG_XIP_PHYS_ADDR + cmp r6, r0 + movcc r6, r0 + + sub r6, r6, #1 + bic r6, r6, #(PMSAv8_MINALIGN - 1) + + orr r5, r5, #(PMSAv8_AP_PL1RW_PL0NA | PMSAv8_RGN_SHARED | PMSAv8_BAR_XN) + orr r6, r6, #(PMSAv8_LAR_IDX(PMSAv8_RGN_DEVICE_nGnRnE) | PMSAv8_LAR_EN) + +#ifdef CONFIG_CPU_V7M + /* There is no alias for n == 4 */ + mov r0, #4 + str r0, [r12, #PMSAv8_RNR] @ PRSEL isb + str r5, [r12, #PMSAv8_RBAR_A(0)] + str r6, [r12, #PMSAv8_RLAR_A(0)] +#else + mcr p15, 0, r5, c6, c10, 1 @ PRBAR4 + mcr p15, 0, r6, c6, c10, 2 @ PRLAR4 +#endif +#endif ret lr -ENDPROC(__setup_mpu) +ENDPROC(__setup_pmsa_v8) #ifdef CONFIG_SMP /* * r6: pointer at mpu_rgn_info */ + .text ENTRY(__secondary_setup_mpu) + /* Use MPU region info supplied by __cpu_up */ + ldr r6, [r7] @ get secondary_data.mpu_rgn_info + /* Probe for v7 PMSA compliance */ mrc p15, 0, r0, c0, c1, 4 @ Read ID_MMFR0 and r0, r0, #(MMFR0_PMSA) @ PMSA field teq r0, #(MMFR0_PMSAv7) @ PMSA v7 - bne __error_p + beq __secondary_setup_pmsa_v7 + teq r0, #(MMFR0_PMSAv8) @ PMSA v8 + beq __secondary_setup_pmsa_v8 + b __error_p +ENDPROC(__secondary_setup_mpu) +/* + * r6: pointer at mpu_rgn_info + */ +ENTRY(__secondary_setup_pmsa_v7) /* Determine whether the D/I-side memory map is unified. We set the * flags here and continue to use them for the rest of this function */ mrc p15, 0, r0, c0, c0, 4 @ MPUIR @@ -328,25 +485,45 @@ ENTRY(__secondary_setup_mpu) ldr r6, [r3, #MPU_RGN_DRSR] ldr r5, [r3, #MPU_RGN_DRACR] - setup_region r0, r5, r6, MPU_DATA_SIDE + setup_region r0, r5, r6, PMSAv7_DATA_SIDE beq 2f - setup_region r0, r5, r6, MPU_INSTR_SIDE + setup_region r0, r5, r6, PMSAv7_INSTR_SIDE 2: isb mrc p15, 0, r0, c0, c0, 4 @ Reevaluate the MPUIR cmp r4, #0 bgt 1b - /* Enable the MPU */ - mrc p15, 0, r0, c1, c0, 0 @ Read SCTLR - bic r0, r0, #CR_BR @ Disable the 'default mem-map' - orr r0, r0, #CR_M @ Set SCTRL.M (MPU on) - mcr p15, 0, r0, c1, c0, 0 @ Enable MPU + ret lr +ENDPROC(__secondary_setup_pmsa_v7) + +ENTRY(__secondary_setup_pmsa_v8) + ldr r4, [r6, #MPU_RNG_INFO_USED] +#ifndef CONFIG_XIP_KERNEL + add r4, r4, #1 +#endif + mov r5, #MPU_RNG_SIZE + add r3, r6, #MPU_RNG_INFO_RNGS + mla r3, r4, r5, r3 + +1: + sub r3, r3, #MPU_RNG_SIZE + sub r4, r4, #1 + + mcr p15, 0, r4, c6, c2, 1 @ PRSEL isb - ret lr -ENDPROC(__secondary_setup_mpu) + ldr r5, [r3, #MPU_RGN_PRBAR] + ldr r6, [r3, #MPU_RGN_PRLAR] + mcr p15, 0, r5, c6, c3, 0 @ PRBAR + mcr p15, 0, r6, c6, c3, 1 @ PRLAR + + cmp r4, #0 + bgt 1b + + ret lr +ENDPROC(__secondary_setup_pmsa_v8) #endif /* CONFIG_SMP */ #endif /* CONFIG_ARM_MPU */ #include "head-common.S" diff --git a/arch/arm/kernel/machine_kexec.c b/arch/arm/kernel/machine_kexec.c index 6b38d7a634c1..dd2eb5f76b9f 100644 --- a/arch/arm/kernel/machine_kexec.c +++ b/arch/arm/kernel/machine_kexec.c @@ -83,7 +83,7 @@ void machine_crash_nonpanic_core(void *unused) { struct pt_regs regs; - crash_setup_regs(®s, NULL); + crash_setup_regs(®s, get_irq_regs()); printk(KERN_DEBUG "CPU %u will stop doing anything useful since another CPU has crashed\n", smp_processor_id()); crash_save_cpu(®s, smp_processor_id()); @@ -95,6 +95,27 @@ void machine_crash_nonpanic_core(void *unused) cpu_relax(); } +void crash_smp_send_stop(void) +{ + static int cpus_stopped; + unsigned long msecs; + + if (cpus_stopped) + return; + + atomic_set(&waiting_for_crash_ipi, num_online_cpus() - 1); + smp_call_function(machine_crash_nonpanic_core, NULL, false); + msecs = 1000; /* Wait at most a second for the other cpus to stop */ + while ((atomic_read(&waiting_for_crash_ipi) > 0) && msecs) { + mdelay(1); + msecs--; + } + if (atomic_read(&waiting_for_crash_ipi) > 0) + pr_warn("Non-crashing CPUs did not react to IPI\n"); + + cpus_stopped = 1; +} + static void machine_kexec_mask_interrupts(void) { unsigned int i; @@ -120,19 +141,8 @@ static void machine_kexec_mask_interrupts(void) void machine_crash_shutdown(struct pt_regs *regs) { - unsigned long msecs; - local_irq_disable(); - - atomic_set(&waiting_for_crash_ipi, num_online_cpus() - 1); - smp_call_function(machine_crash_nonpanic_core, NULL, false); - msecs = 1000; /* Wait at most a second for the other cpus to stop */ - while ((atomic_read(&waiting_for_crash_ipi) > 0) && msecs) { - mdelay(1); - msecs--; - } - if (atomic_read(&waiting_for_crash_ipi) > 0) - pr_warn("Non-crashing CPUs did not react to IPI\n"); + crash_smp_send_stop(); crash_save_cpu(regs, smp_processor_id()); machine_kexec_mask_interrupts(); diff --git a/arch/arm/kernel/perf_event_v6.c b/arch/arm/kernel/perf_event_v6.c index 1d7061a38922..be42c4f66a40 100644 --- a/arch/arm/kernel/perf_event_v6.c +++ b/arch/arm/kernel/perf_event_v6.c @@ -303,12 +303,10 @@ static void armv6pmu_enable_event(struct perf_event *event) } static irqreturn_t -armv6pmu_handle_irq(int irq_num, - void *dev) +armv6pmu_handle_irq(struct arm_pmu *cpu_pmu) { unsigned long pmcr = armv6_pmcr_read(); struct perf_sample_data data; - struct arm_pmu *cpu_pmu = (struct arm_pmu *)dev; struct pmu_hw_events *cpuc = this_cpu_ptr(cpu_pmu->hw_events); struct pt_regs *regs; int idx; diff --git a/arch/arm/kernel/perf_event_v7.c b/arch/arm/kernel/perf_event_v7.c index 870b66c1e4ef..57f01e059f39 100644 --- a/arch/arm/kernel/perf_event_v7.c +++ b/arch/arm/kernel/perf_event_v7.c @@ -946,11 +946,10 @@ static void armv7pmu_disable_event(struct perf_event *event) raw_spin_unlock_irqrestore(&events->pmu_lock, flags); } -static irqreturn_t armv7pmu_handle_irq(int irq_num, void *dev) +static irqreturn_t armv7pmu_handle_irq(struct arm_pmu *cpu_pmu) { u32 pmnc; struct perf_sample_data data; - struct arm_pmu *cpu_pmu = (struct arm_pmu *)dev; struct pmu_hw_events *cpuc = this_cpu_ptr(cpu_pmu->hw_events); struct pt_regs *regs; int idx; diff --git a/arch/arm/kernel/perf_event_xscale.c b/arch/arm/kernel/perf_event_xscale.c index fcf218da660e..88d1a76f5367 100644 --- a/arch/arm/kernel/perf_event_xscale.c +++ b/arch/arm/kernel/perf_event_xscale.c @@ -142,11 +142,10 @@ xscale1_pmnc_counter_has_overflowed(unsigned long pmnc, } static irqreturn_t -xscale1pmu_handle_irq(int irq_num, void *dev) +xscale1pmu_handle_irq(struct arm_pmu *cpu_pmu) { unsigned long pmnc; struct perf_sample_data data; - struct arm_pmu *cpu_pmu = (struct arm_pmu *)dev; struct pmu_hw_events *cpuc = this_cpu_ptr(cpu_pmu->hw_events); struct pt_regs *regs; int idx; @@ -489,11 +488,10 @@ xscale2_pmnc_counter_has_overflowed(unsigned long of_flags, } static irqreturn_t -xscale2pmu_handle_irq(int irq_num, void *dev) +xscale2pmu_handle_irq(struct arm_pmu *cpu_pmu) { unsigned long pmnc, of_flags; struct perf_sample_data data; - struct arm_pmu *cpu_pmu = (struct arm_pmu *)dev; struct pmu_hw_events *cpuc = this_cpu_ptr(cpu_pmu->hw_events); struct pt_regs *regs; int idx; diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 1523cb18b109..225d1c58d2de 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -39,7 +39,7 @@ #include <asm/tls.h> #include <asm/vdso.h> -#ifdef CONFIG_CC_STACKPROTECTOR +#ifdef CONFIG_STACKPROTECTOR #include <linux/stackprotector.h> unsigned long __stack_chk_guard __read_mostly; EXPORT_SYMBOL(__stack_chk_guard); diff --git a/arch/arm/kernel/ptrace.c b/arch/arm/kernel/ptrace.c index 7724b0f661b3..36718a424358 100644 --- a/arch/arm/kernel/ptrace.c +++ b/arch/arm/kernel/ptrace.c @@ -205,6 +205,7 @@ void ptrace_break(struct task_struct *tsk, struct pt_regs *regs) { siginfo_t info; + clear_siginfo(&info); info.si_signo = SIGTRAP; info.si_errno = 0; info.si_code = TRAP_BRKPT; diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c index fc40a2b40595..35ca494c028c 100644 --- a/arch/arm/kernel/setup.c +++ b/arch/arm/kernel/setup.c @@ -754,7 +754,7 @@ int __init arm_add_memory(u64 start, u64 size) else size -= aligned_start - start; -#ifndef CONFIG_ARCH_PHYS_ADDR_T_64BIT +#ifndef CONFIG_PHYS_ADDR_T_64BIT if (aligned_start > ULONG_MAX) { pr_crit("Ignoring memory at 0x%08llx outside 32-bit physical address space\n", (long long)start); diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c index bd8810d4acb3..f09e9d66d605 100644 --- a/arch/arm/kernel/signal.c +++ b/arch/arm/kernel/signal.c @@ -541,6 +541,12 @@ static void handle_signal(struct ksignal *ksig, struct pt_regs *regs) int ret; /* + * Increment event counter and perform fixup for the pre-signal + * frame. + */ + rseq_signal_deliver(regs); + + /* * Set up the stack frame */ if (ksig->ka.sa.sa_flags & SA_SIGINFO) @@ -660,6 +666,7 @@ do_work_pending(struct pt_regs *regs, unsigned int thread_flags, int syscall) } else { clear_thread_flag(TIF_NOTIFY_RESUME); tracehook_notify_resume(regs); + rseq_handle_notify_resume(regs); } } local_irq_disable(); @@ -703,3 +710,10 @@ asmlinkage void addr_limit_check_failed(void) { addr_limit_user_check(); } + +#ifdef CONFIG_DEBUG_RSEQ +asmlinkage void do_rseq_syscall(struct pt_regs *regs) +{ + rseq_syscall(regs); +} +#endif diff --git a/arch/arm/kernel/smp.c b/arch/arm/kernel/smp.c index 2da087926ebe..0978282d5fc2 100644 --- a/arch/arm/kernel/smp.c +++ b/arch/arm/kernel/smp.c @@ -31,6 +31,7 @@ #include <linux/irq_work.h> #include <linux/atomic.h> +#include <asm/bugs.h> #include <asm/smp.h> #include <asm/cacheflush.h> #include <asm/cpu.h> @@ -236,8 +237,6 @@ int __cpu_disable(void) flush_cache_louis(); local_flush_tlb_all(); - clear_tasks_mm_cpumask(cpu); - return 0; } @@ -255,6 +254,7 @@ void __cpu_die(unsigned int cpu) } pr_debug("CPU%u: shutdown\n", cpu); + clear_tasks_mm_cpumask(cpu); /* * platform_cpu_kill() is generally expected to do the powering off * and/or cutting of clocks to the dying CPU. Optionally, this may @@ -405,6 +405,9 @@ asmlinkage void secondary_start_kernel(void) * before we continue - which happens after __cpu_up returns. */ set_cpu_online(cpu, true); + + check_other_bugs(); + complete(&cpu_running); local_irq_enable(); diff --git a/arch/arm/kernel/suspend.c b/arch/arm/kernel/suspend.c index a40ebb7c0896..d08099269e35 100644 --- a/arch/arm/kernel/suspend.c +++ b/arch/arm/kernel/suspend.c @@ -3,6 +3,7 @@ #include <linux/slab.h> #include <linux/mm_types.h> +#include <asm/bugs.h> #include <asm/cacheflush.h> #include <asm/idmap.h> #include <asm/pgalloc.h> @@ -36,6 +37,7 @@ int cpu_suspend(unsigned long arg, int (*fn)(unsigned long)) cpu_switch_mm(mm->pgd, mm); local_flush_bp_all(); local_flush_tlb_all(); + check_other_bugs(); } return ret; diff --git a/arch/arm/kernel/swp_emulate.c b/arch/arm/kernel/swp_emulate.c index 3bda08bee674..80517f293eb9 100644 --- a/arch/arm/kernel/swp_emulate.c +++ b/arch/arm/kernel/swp_emulate.c @@ -91,18 +91,6 @@ static int proc_status_show(struct seq_file *m, void *v) seq_printf(m, "Last process:\t\t%d\n", previous_pid); return 0; } - -static int proc_status_open(struct inode *inode, struct file *file) -{ - return single_open(file, proc_status_show, PDE_DATA(inode)); -} - -static const struct file_operations proc_status_fops = { - .open = proc_status_open, - .read = seq_read, - .llseek = seq_lseek, - .release = single_release, -}; #endif /* @@ -112,6 +100,7 @@ static void set_segfault(struct pt_regs *regs, unsigned long addr) { siginfo_t info; + clear_siginfo(&info); down_read(¤t->mm->mmap_sem); if (find_vma(current->mm, addr) == NULL) info.si_code = SEGV_MAPERR; @@ -260,7 +249,8 @@ static int __init swp_emulation_init(void) return 0; #ifdef CONFIG_PROC_FS - if (!proc_create("cpu/swp_emulation", S_IRUGO, NULL, &proc_status_fops)) + if (!proc_create_single("cpu/swp_emulation", S_IRUGO, NULL, + proc_status_show)) return -ENOMEM; #endif /* CONFIG_PROC_FS */ diff --git a/arch/arm/kernel/sys_oabi-compat.c b/arch/arm/kernel/sys_oabi-compat.c index b9786f491873..1df21a61e379 100644 --- a/arch/arm/kernel/sys_oabi-compat.c +++ b/arch/arm/kernel/sys_oabi-compat.c @@ -286,7 +286,7 @@ asmlinkage long sys_oabi_epoll_wait(int epfd, return -EINVAL; if (!access_ok(VERIFY_WRITE, events, sizeof(*events) * maxevents)) return -EFAULT; - kbuf = kmalloc(sizeof(*kbuf) * maxevents, GFP_KERNEL); + kbuf = kmalloc_array(maxevents, sizeof(*kbuf), GFP_KERNEL); if (!kbuf) return -ENOMEM; fs = get_fs(); @@ -324,7 +324,7 @@ asmlinkage long sys_oabi_semtimedop(int semid, return -EINVAL; if (!access_ok(VERIFY_READ, tsops, sizeof(*tsops) * nsops)) return -EFAULT; - sops = kmalloc(sizeof(*sops) * nsops, GFP_KERNEL); + sops = kmalloc_array(nsops, sizeof(*sops), GFP_KERNEL); if (!sops) return -ENOMEM; err = 0; diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index 5e3633c24e63..badf02ca3693 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -19,6 +19,7 @@ #include <linux/uaccess.h> #include <linux/hardirq.h> #include <linux/kdebug.h> +#include <linux/kprobes.h> #include <linux/module.h> #include <linux/kexec.h> #include <linux/bug.h> @@ -417,7 +418,8 @@ void unregister_undef_hook(struct undef_hook *hook) raw_spin_unlock_irqrestore(&undef_lock, flags); } -static int call_undef_hook(struct pt_regs *regs, unsigned int instr) +static nokprobe_inline +int call_undef_hook(struct pt_regs *regs, unsigned int instr) { struct undef_hook *hook; unsigned long flags; @@ -439,6 +441,7 @@ asmlinkage void do_undefinstr(struct pt_regs *regs) siginfo_t info; void __user *pc; + clear_siginfo(&info); pc = (void __user *)instruction_pointer(regs); if (processor_mode(regs) == SVC_MODE) { @@ -490,6 +493,7 @@ die_sig: arm_notify_die("Oops - undefined instruction", regs, &info, 0, 6); } +NOKPROBE_SYMBOL(do_undefinstr) /* * Handle FIQ similarly to NMI on x86 systems. @@ -537,6 +541,7 @@ static int bad_syscall(int n, struct pt_regs *regs) { siginfo_t info; + clear_siginfo(&info); if ((current->personality & PER_MASK) != PER_LINUX) { send_sig(SIGSEGV, current, 1); return regs->ARM_r0; @@ -604,6 +609,7 @@ asmlinkage int arm_syscall(int no, struct pt_regs *regs) { siginfo_t info; + clear_siginfo(&info); if ((no >> 16) != (__ARM_NR_BASE>> 16)) return bad_syscall(no, regs); @@ -740,6 +746,8 @@ baddataabort(int code, unsigned long instr, struct pt_regs *regs) unsigned long addr = instruction_pointer(regs); siginfo_t info; + clear_siginfo(&info); + #ifdef CONFIG_DEBUG_USER if (user_debug & UDBG_BADABORT) { pr_err("[%d] %s: bad data abort: code %d instr 0x%08lx\n", diff --git a/arch/arm/kernel/vmlinux-xip.lds.S b/arch/arm/kernel/vmlinux-xip.lds.S index d32f5d35f602..3593d5c1acd2 100644 --- a/arch/arm/kernel/vmlinux-xip.lds.S +++ b/arch/arm/kernel/vmlinux-xip.lds.S @@ -13,6 +13,7 @@ #include <asm/cache.h> #include <asm/thread_info.h> #include <asm/memory.h> +#include <asm/mpu.h> #include <asm/page.h> #include "vmlinux.lds.h" @@ -148,6 +149,9 @@ SECTIONS __init_end = .; BSS_SECTION(0, 0, 8) +#ifdef CONFIG_ARM_MPU + . = ALIGN(PMSAv8_MINALIGN); +#endif _end = .; STABS_DEBUG diff --git a/arch/arm/kernel/vmlinux.lds.S b/arch/arm/kernel/vmlinux.lds.S index b77dc675ae55..23150c0f0f4d 100644 --- a/arch/arm/kernel/vmlinux.lds.S +++ b/arch/arm/kernel/vmlinux.lds.S @@ -12,6 +12,7 @@ #include <asm/cache.h> #include <asm/thread_info.h> #include <asm/memory.h> +#include <asm/mpu.h> #include <asm/page.h> #include <asm/pgtable.h> @@ -54,6 +55,9 @@ SECTIONS . = ALIGN(1<<SECTION_SHIFT); #endif +#ifdef CONFIG_ARM_MPU + . = ALIGN(PMSAv8_MINALIGN); +#endif .text : { /* Real text segment */ _stext = .; /* Text and read-only data */ ARM_TEXT @@ -143,6 +147,9 @@ SECTIONS _edata = .; BSS_SECTION(0, 0, 0) +#ifdef CONFIG_ARM_MPU + . = ALIGN(PMSAv8_MINALIGN); +#endif _end = .; STABS_DEBUG diff --git a/arch/arm/kernel/vmlinux.lds.h b/arch/arm/kernel/vmlinux.lds.h index 71281e08e1d4..ae5fdff18406 100644 --- a/arch/arm/kernel/vmlinux.lds.h +++ b/arch/arm/kernel/vmlinux.lds.h @@ -27,24 +27,24 @@ #define PROC_INFO \ . = ALIGN(4); \ - VMLINUX_SYMBOL(__proc_info_begin) = .; \ + __proc_info_begin = .; \ *(.proc.info.init) \ - VMLINUX_SYMBOL(__proc_info_end) = .; + __proc_info_end = .; #define HYPERVISOR_TEXT \ - VMLINUX_SYMBOL(__hyp_text_start) = .; \ + __hyp_text_start = .; \ *(.hyp.text) \ - VMLINUX_SYMBOL(__hyp_text_end) = .; + __hyp_text_end = .; #define IDMAP_TEXT \ ALIGN_FUNCTION(); \ - VMLINUX_SYMBOL(__idmap_text_start) = .; \ + __idmap_text_start = .; \ *(.idmap.text) \ - VMLINUX_SYMBOL(__idmap_text_end) = .; \ + __idmap_text_end = .; \ . = ALIGN(PAGE_SIZE); \ - VMLINUX_SYMBOL(__hyp_idmap_text_start) = .; \ + __hyp_idmap_text_start = .; \ *(.hyp.idmap.text) \ - VMLINUX_SYMBOL(__hyp_idmap_text_end) = .; + __hyp_idmap_text_end = .; #define ARM_DISCARD \ *(.ARM.exidx.exit.text) \ diff --git a/arch/arm/kvm/hyp/Makefile b/arch/arm/kvm/hyp/Makefile index 7fc0638f263a..d2b5ec9c4b92 100644 --- a/arch/arm/kvm/hyp/Makefile +++ b/arch/arm/kvm/hyp/Makefile @@ -23,3 +23,11 @@ obj-$(CONFIG_KVM_ARM_HOST) += hyp-entry.o obj-$(CONFIG_KVM_ARM_HOST) += switch.o CFLAGS_switch.o += $(CFLAGS_ARMV7VE) obj-$(CONFIG_KVM_ARM_HOST) += s2-setup.o + +# KVM code is run at a different exception code with a different map, so +# compiler instrumentation that inserts callbacks or checks into the code may +# cause crashes. Just disable it. +GCOV_PROFILE := n +KASAN_SANITIZE := n +UBSAN_SANITIZE := n +KCOV_INSTRUMENT := n diff --git a/arch/arm/kvm/hyp/hyp-entry.S b/arch/arm/kvm/hyp/hyp-entry.S index 95a2faefc070..aa3f9a9837ac 100644 --- a/arch/arm/kvm/hyp/hyp-entry.S +++ b/arch/arm/kvm/hyp/hyp-entry.S @@ -16,6 +16,7 @@ * Foundation, 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. */ +#include <linux/arm-smccc.h> #include <linux/linkage.h> #include <asm/kvm_arm.h> #include <asm/kvm_asm.h> @@ -71,6 +72,90 @@ __kvm_hyp_vector: W(b) hyp_irq W(b) hyp_fiq +#ifdef CONFIG_HARDEN_BRANCH_PREDICTOR + .align 5 +__kvm_hyp_vector_ic_inv: + .global __kvm_hyp_vector_ic_inv + + /* + * We encode the exception entry in the bottom 3 bits of + * SP, and we have to guarantee to be 8 bytes aligned. + */ + W(add) sp, sp, #1 /* Reset 7 */ + W(add) sp, sp, #1 /* Undef 6 */ + W(add) sp, sp, #1 /* Syscall 5 */ + W(add) sp, sp, #1 /* Prefetch abort 4 */ + W(add) sp, sp, #1 /* Data abort 3 */ + W(add) sp, sp, #1 /* HVC 2 */ + W(add) sp, sp, #1 /* IRQ 1 */ + W(nop) /* FIQ 0 */ + + mcr p15, 0, r0, c7, c5, 0 /* ICIALLU */ + isb + + b decode_vectors + + .align 5 +__kvm_hyp_vector_bp_inv: + .global __kvm_hyp_vector_bp_inv + + /* + * We encode the exception entry in the bottom 3 bits of + * SP, and we have to guarantee to be 8 bytes aligned. + */ + W(add) sp, sp, #1 /* Reset 7 */ + W(add) sp, sp, #1 /* Undef 6 */ + W(add) sp, sp, #1 /* Syscall 5 */ + W(add) sp, sp, #1 /* Prefetch abort 4 */ + W(add) sp, sp, #1 /* Data abort 3 */ + W(add) sp, sp, #1 /* HVC 2 */ + W(add) sp, sp, #1 /* IRQ 1 */ + W(nop) /* FIQ 0 */ + + mcr p15, 0, r0, c7, c5, 6 /* BPIALL */ + isb + +decode_vectors: + +#ifdef CONFIG_THUMB2_KERNEL + /* + * Yet another silly hack: Use VPIDR as a temp register. + * Thumb2 is really a pain, as SP cannot be used with most + * of the bitwise instructions. The vect_br macro ensures + * things gets cleaned-up. + */ + mcr p15, 4, r0, c0, c0, 0 /* VPIDR */ + mov r0, sp + and r0, r0, #7 + sub sp, sp, r0 + push {r1, r2} + mov r1, r0 + mrc p15, 4, r0, c0, c0, 0 /* VPIDR */ + mrc p15, 0, r2, c0, c0, 0 /* MIDR */ + mcr p15, 4, r2, c0, c0, 0 /* VPIDR */ +#endif + +.macro vect_br val, targ +ARM( eor sp, sp, #\val ) +ARM( tst sp, #7 ) +ARM( eorne sp, sp, #\val ) + +THUMB( cmp r1, #\val ) +THUMB( popeq {r1, r2} ) + + beq \targ +.endm + + vect_br 0, hyp_fiq + vect_br 1, hyp_irq + vect_br 2, hyp_hvc + vect_br 3, hyp_dabt + vect_br 4, hyp_pabt + vect_br 5, hyp_svc + vect_br 6, hyp_undef + vect_br 7, hyp_reset +#endif + .macro invalid_vector label, cause .align \label: mov r0, #\cause @@ -118,7 +203,7 @@ hyp_hvc: lsr r2, r2, #16 and r2, r2, #0xff cmp r2, #0 - bne guest_trap @ Guest called HVC + bne guest_hvc_trap @ Guest called HVC /* * Getting here means host called HVC, we shift parameters and branch @@ -149,7 +234,14 @@ hyp_hvc: bx ip 1: - push {lr} + /* + * Pushing r2 here is just a way of keeping the stack aligned to + * 8 bytes on any path that can trigger a HYP exception. Here, + * we may well be about to jump into the guest, and the guest + * exit would otherwise be badly decoded by our fancy + * "decode-exception-without-a-branch" code... + */ + push {r2, lr} mov lr, r0 mov r0, r1 @@ -159,7 +251,21 @@ hyp_hvc: THUMB( orr lr, #1) blx lr @ Call the HYP function - pop {lr} + pop {r2, lr} + eret + +guest_hvc_trap: + movw r2, #:lower16:ARM_SMCCC_ARCH_WORKAROUND_1 + movt r2, #:upper16:ARM_SMCCC_ARCH_WORKAROUND_1 + ldr r0, [sp] @ Guest's r0 + teq r0, r2 + bne guest_trap + add sp, sp, #12 + @ Returns: + @ r0 = 0 + @ r1 = HSR value (perfectly predictable) + @ r2 = ARM_SMCCC_ARCH_WORKAROUND_1 + mov r0, #0 eret guest_trap: diff --git a/arch/arm/lib/getuser.S b/arch/arm/lib/getuser.S index df73914e81c8..746e7801dcdf 100644 --- a/arch/arm/lib/getuser.S +++ b/arch/arm/lib/getuser.S @@ -38,6 +38,7 @@ ENTRY(__get_user_1) mov r0, #0 ret lr ENDPROC(__get_user_1) +_ASM_NOKPROBE(__get_user_1) ENTRY(__get_user_2) check_uaccess r0, 2, r1, r2, __get_user_bad @@ -58,6 +59,7 @@ rb .req r0 mov r0, #0 ret lr ENDPROC(__get_user_2) +_ASM_NOKPROBE(__get_user_2) ENTRY(__get_user_4) check_uaccess r0, 4, r1, r2, __get_user_bad @@ -65,6 +67,7 @@ ENTRY(__get_user_4) mov r0, #0 ret lr ENDPROC(__get_user_4) +_ASM_NOKPROBE(__get_user_4) ENTRY(__get_user_8) check_uaccess r0, 8, r1, r2, __get_user_bad8 @@ -78,6 +81,7 @@ ENTRY(__get_user_8) mov r0, #0 ret lr ENDPROC(__get_user_8) +_ASM_NOKPROBE(__get_user_8) #ifdef __ARMEB__ ENTRY(__get_user_32t_8) @@ -91,6 +95,7 @@ ENTRY(__get_user_32t_8) mov r0, #0 ret lr ENDPROC(__get_user_32t_8) +_ASM_NOKPROBE(__get_user_32t_8) ENTRY(__get_user_64t_1) check_uaccess r0, 1, r1, r2, __get_user_bad8 @@ -98,6 +103,7 @@ ENTRY(__get_user_64t_1) mov r0, #0 ret lr ENDPROC(__get_user_64t_1) +_ASM_NOKPROBE(__get_user_64t_1) ENTRY(__get_user_64t_2) check_uaccess r0, 2, r1, r2, __get_user_bad8 @@ -114,6 +120,7 @@ rb .req r0 mov r0, #0 ret lr ENDPROC(__get_user_64t_2) +_ASM_NOKPROBE(__get_user_64t_2) ENTRY(__get_user_64t_4) check_uaccess r0, 4, r1, r2, __get_user_bad8 @@ -121,6 +128,7 @@ ENTRY(__get_user_64t_4) mov r0, #0 ret lr ENDPROC(__get_user_64t_4) +_ASM_NOKPROBE(__get_user_64t_4) #endif __get_user_bad8: @@ -131,6 +139,8 @@ __get_user_bad: ret lr ENDPROC(__get_user_bad) ENDPROC(__get_user_bad8) +_ASM_NOKPROBE(__get_user_bad) +_ASM_NOKPROBE(__get_user_bad8) .pushsection __ex_table, "a" .long 1b, __get_user_bad diff --git a/arch/arm/mach-axxia/Kconfig b/arch/arm/mach-axxia/Kconfig index bb2ce1c63fd9..d3eae6037913 100644 --- a/arch/arm/mach-axxia/Kconfig +++ b/arch/arm/mach-axxia/Kconfig @@ -2,7 +2,6 @@ config ARCH_AXXIA bool "LSI Axxia platforms" depends on ARCH_MULTI_V7 && ARM_LPAE - select ARCH_DMA_ADDR_T_64BIT select ARM_AMBA select ARM_GIC select ARM_TIMER_SP804 diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig index c2f3b0d216a4..c46a728df44e 100644 --- a/arch/arm/mach-bcm/Kconfig +++ b/arch/arm/mach-bcm/Kconfig @@ -211,7 +211,6 @@ config ARCH_BRCMSTB select BRCMSTB_L2_IRQ select BCM7120_L2_IRQ select ARCH_HAS_HOLES_MEMORYMODEL - select ARCH_DMA_ADDR_T_64BIT if ARM_LPAE select ZONE_DMA if ARM_LPAE select SOC_BRCMSTB select SOC_BUS diff --git a/arch/arm/mach-berlin/Kconfig b/arch/arm/mach-berlin/Kconfig index 63ab1d368625..3d719cf645e3 100644 --- a/arch/arm/mach-berlin/Kconfig +++ b/arch/arm/mach-berlin/Kconfig @@ -23,8 +23,12 @@ config MACH_BERLIN_BG2 config MACH_BERLIN_BG2CD bool "Marvell Armada 1500-mini (BG2CD)" + select ARM_ERRATA_754322 + select ARM_ERRATA_775420 + select ARM_GLOBAL_TIMER select CACHE_L2X0 - select HAVE_ARM_TWD if SMP + select HAVE_ARM_SCU + select HAVE_ARM_TWD select PINCTRL_BERLIN_BG2CD config MACH_BERLIN_BG2Q diff --git a/arch/arm/mach-berlin/berlin.c b/arch/arm/mach-berlin/berlin.c index ac181c6797ee..2424ad40190c 100644 --- a/arch/arm/mach-berlin/berlin.c +++ b/arch/arm/mach-berlin/berlin.c @@ -1,3 +1,4 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Device Tree support for Marvell Berlin SoCs. * @@ -5,10 +6,6 @@ * * based on GPL'ed 2.6 kernel sources * (c) Marvell International Ltd. - * - * This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. */ #include <linux/init.h> diff --git a/arch/arm/mach-berlin/headsmp.S b/arch/arm/mach-berlin/headsmp.S index dc82a3486b05..3057885d9772 100644 --- a/arch/arm/mach-berlin/headsmp.S +++ b/arch/arm/mach-berlin/headsmp.S @@ -1,11 +1,8 @@ +/* SPDX-License-Identifier: GPL-2.0 */ /* * Copyright (C) 2014 Marvell Technology Group Ltd. * * Antoine Ténart <antoine.tenart@free-electrons.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. */ #include <linux/linkage.h> diff --git a/arch/arm/mach-berlin/platsmp.c b/arch/arm/mach-berlin/platsmp.c index 7586b7aec272..593fc4a69d84 100644 --- a/arch/arm/mach-berlin/platsmp.c +++ b/arch/arm/mach-berlin/platsmp.c @@ -1,11 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (C) 2014 Marvell Technology Group Ltd. * * Antoine Ténart <antoine.tenart@free-electrons.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. */ #include <linux/io.h> @@ -81,7 +78,6 @@ static void __init berlin_smp_prepare_cpus(unsigned int max_cpus) goto unmap_scu; scu_enable(scu_base); - flush_cache_all(); /* * Write the first instruction the CPU will execute after being reset diff --git a/arch/arm/mach-davinci/aemif.c b/arch/arm/mach-davinci/aemif.c index ff8b7e76b6e9..e4ab3f3a2a1f 100644 --- a/arch/arm/mach-davinci/aemif.c +++ b/arch/arm/mach-davinci/aemif.c @@ -189,7 +189,7 @@ int davinci_aemif_setup(struct platform_device *pdev) * Setup Async configuration register in case we did not boot * from NAND and so bootloader did not bother to set it up. */ - val = davinci_aemif_readl(base, A1CR_OFFSET + pdev->id * 4); + val = davinci_aemif_readl(base, A1CR_OFFSET + pdata->core_chipsel * 4); /* * Extended Wait is not valid and Select Strobe mode is not * used @@ -198,13 +198,13 @@ int davinci_aemif_setup(struct platform_device *pdev) if (pdata->options & NAND_BUSWIDTH_16) val |= 0x1; - davinci_aemif_writel(base, A1CR_OFFSET + pdev->id * 4, val); + davinci_aemif_writel(base, A1CR_OFFSET + pdata->core_chipsel * 4, val); clkrate = clk_get_rate(clk); if (pdata->timing) - ret = davinci_aemif_setup_timing(pdata->timing, base, pdev->id, - clkrate); + ret = davinci_aemif_setup_timing(pdata->timing, base, + pdata->core_chipsel, clkrate); if (ret < 0) dev_dbg(&pdev->dev, "NAND timing values setup fail\n"); diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c index 004f9c8de032..14a6fc061744 100644 --- a/arch/arm/mach-davinci/board-da830-evm.c +++ b/arch/arm/mach-davinci/board-da830-evm.c @@ -205,12 +205,17 @@ static const short da830_evm_mmc_sd_pins[] = { -1 }; +#define DA830_MMCSD_WP_PIN GPIO_TO_PIN(2, 1) +#define DA830_MMCSD_CD_PIN GPIO_TO_PIN(2, 2) + static struct gpiod_lookup_table mmc_gpios_table = { .dev_id = "da830-mmc.0", .table = { /* gpio chip 1 contains gpio range 32-63 */ - GPIO_LOOKUP("davinci_gpio.1", 2, "cd", GPIO_ACTIVE_LOW), - GPIO_LOOKUP("davinci_gpio.1", 1, "wp", GPIO_ACTIVE_LOW), + GPIO_LOOKUP("davinci_gpio.0", DA830_MMCSD_CD_PIN, "cd", + GPIO_ACTIVE_LOW), + GPIO_LOOKUP("davinci_gpio.0", DA830_MMCSD_WP_PIN, "wp", + GPIO_ACTIVE_LOW), }, }; @@ -310,6 +315,7 @@ static struct davinci_aemif_timing da830_evm_nandflash_timing = { }; static struct davinci_nand_pdata da830_evm_nand_pdata = { + .core_chipsel = 1, .parts = da830_evm_nand_partitions, .nr_parts = ARRAY_SIZE(da830_evm_nand_partitions), .ecc_mode = NAND_ECC_HW, diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index 3063478bcc36..e22fb40e34bc 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -244,6 +244,7 @@ static struct davinci_aemif_timing da850_evm_nandflash_timing = { }; static struct davinci_nand_pdata da850_evm_nandflash_data = { + .core_chipsel = 1, .parts = da850_evm_nandflash_partition, .nr_parts = ARRAY_SIZE(da850_evm_nandflash_partition), .ecc_mode = NAND_ECC_HW, @@ -763,12 +764,17 @@ static const short da850_evm_mcasp_pins[] __initconst = { -1 }; +#define DA850_MMCSD_CD_PIN GPIO_TO_PIN(4, 0) +#define DA850_MMCSD_WP_PIN GPIO_TO_PIN(4, 1) + static struct gpiod_lookup_table mmc_gpios_table = { .dev_id = "da830-mmc.0", .table = { /* gpio chip 2 contains gpio range 64-95 */ - GPIO_LOOKUP("davinci_gpio.2", 0, "cd", GPIO_ACTIVE_LOW), - GPIO_LOOKUP("davinci_gpio.2", 1, "wp", GPIO_ACTIVE_LOW), + GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_CD_PIN, "cd", + GPIO_ACTIVE_LOW), + GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_WP_PIN, "wp", + GPIO_ACTIVE_LOW), }, }; diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c index cb30637d9eaf..a3377f959444 100644 --- a/arch/arm/mach-davinci/board-dm355-evm.c +++ b/arch/arm/mach-davinci/board-dm355-evm.c @@ -19,6 +19,7 @@ #include <linux/gpio.h> #include <linux/gpio/machine.h> #include <linux/clk.h> +#include <linux/dm9000.h> #include <linux/videodev2.h> #include <media/i2c/tvp514x.h> #include <linux/spi/spi.h> @@ -77,6 +78,7 @@ static struct mtd_partition davinci_nand_partitions[] = { }; static struct davinci_nand_pdata davinci_nand_data = { + .core_chipsel = 0, .mask_chipsel = BIT(14), .parts = davinci_nand_partitions, .nr_parts = ARRAY_SIZE(davinci_nand_partitions), @@ -109,12 +111,15 @@ static struct platform_device davinci_nand_device = { }, }; +#define DM355_I2C_SDA_PIN GPIO_TO_PIN(0, 15) +#define DM355_I2C_SCL_PIN GPIO_TO_PIN(0, 14) + static struct gpiod_lookup_table i2c_recovery_gpiod_table = { - .dev_id = "i2c_davinci", + .dev_id = "i2c_davinci.1", .table = { - GPIO_LOOKUP("davinci_gpio", 15, "sda", + GPIO_LOOKUP("davinci_gpio.0", DM355_I2C_SDA_PIN, "sda", GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), - GPIO_LOOKUP("davinci_gpio", 14, "scl", + GPIO_LOOKUP("davinci_gpio.0", DM355_I2C_SCL_PIN, "scl", GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), }, }; @@ -179,11 +184,16 @@ static struct resource dm355evm_dm9000_rsrc[] = { }, }; +static struct dm9000_plat_data dm335evm_dm9000_platdata; + static struct platform_device dm355evm_dm9000 = { .name = "dm9000", .id = -1, .resource = dm355evm_dm9000_rsrc, .num_resources = ARRAY_SIZE(dm355evm_dm9000_rsrc), + .dev = { + .platform_data = &dm335evm_dm9000_platdata, + }, }; static struct tvp514x_platform_data tvp5146_pdata = { diff --git a/arch/arm/mach-davinci/board-dm355-leopard.c b/arch/arm/mach-davinci/board-dm355-leopard.c index 59743bd76793..8249a0bf69f0 100644 --- a/arch/arm/mach-davinci/board-dm355-leopard.c +++ b/arch/arm/mach-davinci/board-dm355-leopard.c @@ -72,6 +72,7 @@ static struct mtd_partition davinci_nand_partitions[] = { }; static struct davinci_nand_pdata davinci_nand_data = { + .core_chipsel = 0, .mask_chipsel = BIT(14), .parts = davinci_nand_partitions, .nr_parts = ARRAY_SIZE(davinci_nand_partitions), diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c index 0ac085b58a2b..435f7ec7d9af 100644 --- a/arch/arm/mach-davinci/board-dm365-evm.c +++ b/arch/arm/mach-davinci/board-dm365-evm.c @@ -138,6 +138,7 @@ static struct mtd_partition davinci_nand_partitions[] = { }; static struct davinci_nand_pdata davinci_nand_data = { + .core_chipsel = 0, .mask_chipsel = BIT(14), .parts = davinci_nand_partitions, .nr_parts = ARRAY_SIZE(davinci_nand_partitions), diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c index 95b55aae1366..48436f74fd71 100644 --- a/arch/arm/mach-davinci/board-dm644x-evm.c +++ b/arch/arm/mach-davinci/board-dm644x-evm.c @@ -17,6 +17,7 @@ #include <linux/i2c.h> #include <linux/platform_data/pcf857x.h> #include <linux/platform_data/at24.h> +#include <linux/platform_data/gpio-davinci.h> #include <linux/mtd/mtd.h> #include <linux/mtd/rawnand.h> #include <linux/mtd/partitions.h> @@ -152,6 +153,7 @@ static struct davinci_aemif_timing davinci_evm_nandflash_timing = { }; static struct davinci_nand_pdata davinci_evm_nandflash_data = { + .core_chipsel = 0, .parts = davinci_evm_nandflash_partition, .nr_parts = ARRAY_SIZE(davinci_evm_nandflash_partition), .ecc_mode = NAND_ECC_HW, @@ -596,12 +598,15 @@ static struct i2c_board_info __initdata i2c_info[] = { }, }; +#define DM644X_I2C_SDA_PIN GPIO_TO_PIN(2, 12) +#define DM644X_I2C_SCL_PIN GPIO_TO_PIN(2, 11) + static struct gpiod_lookup_table i2c_recovery_gpiod_table = { - .dev_id = "i2c_davinci", + .dev_id = "i2c_davinci.1", .table = { - GPIO_LOOKUP("davinci_gpio", 44, "sda", + GPIO_LOOKUP("davinci_gpio.0", DM644X_I2C_SDA_PIN, "sda", GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), - GPIO_LOOKUP("davinci_gpio", 43, "scl", + GPIO_LOOKUP("davinci_gpio.0", DM644X_I2C_SCL_PIN, "scl", GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), }, }; @@ -768,6 +773,8 @@ static __init void davinci_evm_init(void) struct clk *aemif_clk; struct davinci_soc_info *soc_info = &davinci_soc_info; + dm644x_init_devices(); + ret = dm644x_gpio_register(); if (ret) pr_warn("%s: GPIO init failed: %d\n", __func__, ret); diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c index 2d37f5b0e1f5..584064fdabf5 100644 --- a/arch/arm/mach-davinci/board-dm646x-evm.c +++ b/arch/arm/mach-davinci/board-dm646x-evm.c @@ -84,6 +84,7 @@ static struct davinci_aemif_timing dm6467tevm_nandflash_timing = { }; static struct davinci_nand_pdata davinci_nand_data = { + .core_chipsel = 0, .mask_cle = 0x80000, .mask_ale = 0x40000, .parts = davinci_nand_partitions, @@ -532,11 +533,12 @@ static struct vpif_display_config dm646x_vpif_display_config = { .set_clock = set_vpif_clock, .subdevinfo = dm646x_vpif_subdev, .subdev_count = ARRAY_SIZE(dm646x_vpif_subdev), + .i2c_adapter_id = 1, .chan_config[0] = { .outputs = dm6467_ch0_outputs, .output_count = ARRAY_SIZE(dm6467_ch0_outputs), }, - .card_name = "DM646x EVM", + .card_name = "DM646x EVM Video Display", }; /** @@ -674,6 +676,7 @@ static struct vpif_capture_config dm646x_vpif_capture_cfg = { .setup_input_channel_mode = setup_vpif_input_channel_mode, .subdev_info = vpif_capture_sdev_info, .subdev_count = ARRAY_SIZE(vpif_capture_sdev_info), + .i2c_adapter_id = 1, .chan_config[0] = { .inputs = dm6467_ch0_inputs, .input_count = ARRAY_SIZE(dm6467_ch0_inputs), @@ -694,6 +697,7 @@ static struct vpif_capture_config dm646x_vpif_capture_cfg = { .fid_pol = 0, }, }, + .card_name = "DM646x EVM Video Capture", }; static void __init evm_init_video(void) diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c index d1c85484c2e2..37b3e48a21d1 100644 --- a/arch/arm/mach-davinci/board-mityomapl138.c +++ b/arch/arm/mach-davinci/board-mityomapl138.c @@ -400,6 +400,7 @@ static struct mtd_partition mityomapl138_nandflash_partition[] = { }; static struct davinci_nand_pdata mityomapl138_nandflash_data = { + .core_chipsel = 1, .parts = mityomapl138_nandflash_partition, .nr_parts = ARRAY_SIZE(mityomapl138_nandflash_partition), .ecc_mode = NAND_ECC_HW, diff --git a/arch/arm/mach-davinci/board-neuros-osd2.c b/arch/arm/mach-davinci/board-neuros-osd2.c index f2875770fbff..25ad9b0612be 100644 --- a/arch/arm/mach-davinci/board-neuros-osd2.c +++ b/arch/arm/mach-davinci/board-neuros-osd2.c @@ -87,6 +87,7 @@ static struct mtd_partition davinci_ntosd2_nandflash_partition[] = { }; static struct davinci_nand_pdata davinci_ntosd2_nandflash_data = { + .core_chipsel = 0, .parts = davinci_ntosd2_nandflash_partition, .nr_parts = ARRAY_SIZE(davinci_ntosd2_nandflash_partition), .ecc_mode = NAND_ECC_HW, @@ -174,6 +175,8 @@ static __init void davinci_ntosd2_init(void) struct clk *aemif_clk; struct davinci_soc_info *soc_info = &davinci_soc_info; + dm644x_init_devices(); + ret = dm644x_gpio_register(); if (ret) pr_warn("%s: GPIO init failed: %d\n", __func__, ret); diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c index 0d32042b728f..be8b892a6ea7 100644 --- a/arch/arm/mach-davinci/board-omapl138-hawk.c +++ b/arch/arm/mach-davinci/board-omapl138-hawk.c @@ -123,12 +123,16 @@ static const short hawk_mmcsd0_pins[] = { -1 }; +#define DA850_HAWK_MMCSD_CD_PIN GPIO_TO_PIN(3, 12) +#define DA850_HAWK_MMCSD_WP_PIN GPIO_TO_PIN(3, 13) + static struct gpiod_lookup_table mmc_gpios_table = { .dev_id = "da830-mmc.0", .table = { - /* CD: gpio3_12: gpio60: chip 1 contains gpio range 32-63*/ - GPIO_LOOKUP("davinci_gpio.0", 28, "cd", GPIO_ACTIVE_LOW), - GPIO_LOOKUP("davinci_gpio.0", 29, "wp", GPIO_ACTIVE_LOW), + GPIO_LOOKUP("davinci_gpio.0", DA850_HAWK_MMCSD_CD_PIN, "cd", + GPIO_ACTIVE_LOW), + GPIO_LOOKUP("davinci_gpio.0", DA850_HAWK_MMCSD_WP_PIN, "wp", + GPIO_ACTIVE_LOW), }, }; diff --git a/arch/arm/mach-davinci/board-sffsdr.c b/arch/arm/mach-davinci/board-sffsdr.c index 2922da9d1684..e7c1728b0833 100644 --- a/arch/arm/mach-davinci/board-sffsdr.c +++ b/arch/arm/mach-davinci/board-sffsdr.c @@ -134,6 +134,8 @@ static __init void davinci_sffsdr_init(void) { struct davinci_soc_info *soc_info = &davinci_soc_info; + dm644x_init_devices(); + platform_add_devices(davinci_sffsdr_devices, ARRAY_SIZE(davinci_sffsdr_devices)); sffsdr_init_i2c(); diff --git a/arch/arm/mach-davinci/davinci.h b/arch/arm/mach-davinci/davinci.h index 270cef85750a..376cdd51ce9d 100644 --- a/arch/arm/mach-davinci/davinci.h +++ b/arch/arm/mach-davinci/davinci.h @@ -104,6 +104,7 @@ int dm365_gpio_register(void); /* DM644x function declarations */ void dm644x_init(void); +void dm644x_init_devices(void); void dm644x_init_time(void); void dm644x_init_asp(void); int dm644x_init_video(struct vpfe_config *, struct vpbe_config *); diff --git a/arch/arm/mach-davinci/dm644x.c b/arch/arm/mach-davinci/dm644x.c index b409801649e1..a2e8586c8a6d 100644 --- a/arch/arm/mach-davinci/dm644x.c +++ b/arch/arm/mach-davinci/dm644x.c @@ -961,19 +961,14 @@ int __init dm644x_init_video(struct vpfe_config *vpfe_cfg, return 0; } -static int __init dm644x_init_devices(void) +void __init dm644x_init_devices(void) { struct platform_device *edma_pdev; - int ret = 0; - - if (!cpu_is_davinci_dm644x()) - return 0; + int ret; edma_pdev = platform_device_register_full(&dm644x_edma_device); - if (IS_ERR(edma_pdev)) { + if (IS_ERR(edma_pdev)) pr_warn("%s: Failed to register eDMA\n", __func__); - return PTR_ERR(edma_pdev); - } platform_device_register(&dm644x_mdio_device); platform_device_register(&dm644x_emac_device); @@ -982,6 +977,4 @@ static int __init dm644x_init_devices(void) if (ret) pr_warn("%s: watchdog init failed: %d\n", __func__, ret); - return ret; } -postcore_initcall(dm644x_init_devices); diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c index 109ab1fa0d2c..c32ca27ab343 100644 --- a/arch/arm/mach-davinci/dm646x.c +++ b/arch/arm/mach-davinci/dm646x.c @@ -488,7 +488,8 @@ static u8 dm646x_default_priorities[DAVINCI_N_AINTC_IRQ] = { [IRQ_DM646X_MCASP0TXINT] = 7, [IRQ_DM646X_MCASP0RXINT] = 7, [IRQ_DM646X_RESERVED_3] = 7, - [IRQ_DM646X_MCASP1TXINT] = 7, /* clockevent */ + [IRQ_DM646X_MCASP1TXINT] = 7, + [IRQ_TINT0_TINT12] = 7, /* clockevent */ [IRQ_TINT0_TINT34] = 7, /* clocksource */ [IRQ_TINT1_TINT12] = 7, /* DSP timer */ [IRQ_TINT1_TINT34] = 7, /* system tick */ diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c index e70feec6fad5..faf48a3b1fea 100644 --- a/arch/arm/mach-ep93xx/core.c +++ b/arch/arm/mach-ep93xx/core.c @@ -323,7 +323,7 @@ void __init ep93xx_register_eth(struct ep93xx_eth_data *data, int copy_addr) /* All EP93xx devices use the same two GPIO pins for I2C bit-banging */ static struct gpiod_lookup_table ep93xx_i2c_gpiod_table = { - .dev_id = "i2c-gpio", + .dev_id = "i2c-gpio.0", .table = { /* Use local offsets on gpiochip/port "G" */ GPIO_LOOKUP_IDX("G", 1, NULL, 0, @@ -635,6 +635,7 @@ EXPORT_SYMBOL(ep93xx_keypad_release_gpio); *************************************************************************/ static struct resource ep93xx_i2s_resource[] = { DEFINE_RES_MEM(EP93XX_I2S_PHYS_BASE, 0x100), + DEFINE_RES_IRQ(IRQ_EP93XX_SAI), }; static struct platform_device ep93xx_i2s_device = { diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index 647c319f9f5f..b40963cf91c7 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -8,7 +8,6 @@ menuconfig ARCH_EXYNOS bool "Samsung EXYNOS" depends on ARCH_MULTI_V7 - select ARCH_HAS_BANDGAP select ARCH_HAS_HOLES_MEMORYMODEL select ARCH_SUPPORTS_BIG_ENDIAN select ARM_AMBA @@ -108,18 +107,6 @@ config SOC_EXYNOS5420 default y depends on ARCH_EXYNOS5 -config SOC_EXYNOS5440 - bool "SAMSUNG EXYNOS5440" - default y - depends on ARCH_EXYNOS5 - select ARCH_DMA_ADDR_T_64BIT if ARM_LPAE - select HAVE_ARM_ARCH_TIMER - select AUTO_ZRELADDR - select PINCTRL_EXYNOS5440 - select PM_OPP - help - Enable EXYNOS5440 SoC support - config SOC_EXYNOS5800 bool "SAMSUNG EXYNOS5800" default y diff --git a/arch/arm/mach-exynos/common.h b/arch/arm/mach-exynos/common.h index 098f84a149a3..dcd21bb95e3b 100644 --- a/arch/arm/mach-exynos/common.h +++ b/arch/arm/mach-exynos/common.h @@ -21,7 +21,6 @@ #define EXYNOS5250_SOC_ID 0x43520000 #define EXYNOS5410_SOC_ID 0xE5410000 #define EXYNOS5420_SOC_ID 0xE5420000 -#define EXYNOS5440_SOC_ID 0xE5440000 #define EXYNOS5800_SOC_ID 0xE5422000 #define EXYNOS5_SOC_MASK 0xFFFFF000 @@ -39,7 +38,6 @@ IS_SAMSUNG_CPU(exynos4412, EXYNOS4412_CPU_ID, EXYNOS4_CPU_MASK) IS_SAMSUNG_CPU(exynos5250, EXYNOS5250_SOC_ID, EXYNOS5_SOC_MASK) IS_SAMSUNG_CPU(exynos5410, EXYNOS5410_SOC_ID, EXYNOS5_SOC_MASK) IS_SAMSUNG_CPU(exynos5420, EXYNOS5420_SOC_ID, EXYNOS5_SOC_MASK) -IS_SAMSUNG_CPU(exynos5440, EXYNOS5440_SOC_ID, EXYNOS5_SOC_MASK) IS_SAMSUNG_CPU(exynos5800, EXYNOS5800_SOC_ID, EXYNOS5_SOC_MASK) #if defined(CONFIG_SOC_EXYNOS3250) @@ -82,22 +80,12 @@ IS_SAMSUNG_CPU(exynos5800, EXYNOS5800_SOC_ID, EXYNOS5_SOC_MASK) # define soc_is_exynos5420() 0 #endif -#if defined(CONFIG_SOC_EXYNOS5440) -# define soc_is_exynos5440() is_samsung_exynos5440() -#else -# define soc_is_exynos5440() 0 -#endif - #if defined(CONFIG_SOC_EXYNOS5800) # define soc_is_exynos5800() is_samsung_exynos5800() #else # define soc_is_exynos5800() 0 #endif -#define soc_is_exynos4() (soc_is_exynos4210() || soc_is_exynos4412()) -#define soc_is_exynos5() (soc_is_exynos5250() || soc_is_exynos5410() || \ - soc_is_exynos5420() || soc_is_exynos5800()) - extern u32 cp15_save_diag; extern u32 cp15_save_power; @@ -149,6 +137,11 @@ extern void exynos_cpu_restore_register(void); extern void exynos_pm_central_suspend(void); extern int exynos_pm_central_resume(void); extern void exynos_enter_aftr(void); +#ifdef CONFIG_SMP +extern void exynos_scu_enable(void); +#else +static inline void exynos_scu_enable(void) { } +#endif extern struct cpuidle_exynos_data cpuidle_coupled_exynos_data; diff --git a/arch/arm/mach-exynos/exynos.c b/arch/arm/mach-exynos/exynos.c index 8c4f5e342dc1..f4b6c93a7fd0 100644 --- a/arch/arm/mach-exynos/exynos.c +++ b/arch/arm/mach-exynos/exynos.c @@ -24,15 +24,6 @@ #include "common.h" -static struct map_desc exynos4_iodesc[] __initdata = { - { - .virtual = (unsigned long)S5P_VA_COREPERI_BASE, - .pfn = __phys_to_pfn(EXYNOS4_PA_COREPERI), - .length = SZ_8K, - .type = MT_DEVICE, - }, -}; - static struct platform_device exynos_cpuidle = { .name = "exynos_cpuidle", #ifdef CONFIG_ARM_EXYNOS_CPUIDLE @@ -63,15 +54,6 @@ void __init exynos_sysram_init(void) } } -static void __init exynos_init_late(void) -{ - if (of_machine_is_compatible("samsung,exynos5440")) - /* to be supported later */ - return; - - exynos_pm_init(); -} - static int __init exynos_fdt_map_chipid(unsigned long node, const char *uname, int depth, void *data) { @@ -79,8 +61,7 @@ static int __init exynos_fdt_map_chipid(unsigned long node, const char *uname, const __be32 *reg; int len; - if (!of_flat_dt_is_compatible(node, "samsung,exynos4210-chipid") && - !of_flat_dt_is_compatible(node, "samsung,exynos5440-clock")) + if (!of_flat_dt_is_compatible(node, "samsung,exynos4210-chipid")) return 0; reg = of_get_flat_dt_prop(node, "reg", &len); @@ -95,17 +76,6 @@ static int __init exynos_fdt_map_chipid(unsigned long node, const char *uname, return 1; } -/* - * exynos_map_io - * - * register the standard cpu IO areas - */ -static void __init exynos_map_io(void) -{ - if (soc_is_exynos4()) - iotable_init(exynos4_iodesc, ARRAY_SIZE(exynos4_iodesc)); -} - static void __init exynos_init_io(void) { debug_ll_io_init(); @@ -114,8 +84,6 @@ static void __init exynos_init_io(void) /* detect cpu id and rev. */ s5p_init_cpu(S5P_VA_CHIPID); - - exynos_map_io(); } /* @@ -209,7 +177,6 @@ static char const *const exynos_dt_compat[] __initconst = { "samsung,exynos5250", "samsung,exynos5260", "samsung,exynos5420", - "samsung,exynos5440", NULL }; @@ -232,7 +199,7 @@ DT_MACHINE_START(EXYNOS_DT, "SAMSUNG EXYNOS (Flattened Device Tree)") .init_early = exynos_firmware_init, .init_irq = exynos_init_irq, .init_machine = exynos_dt_machine_init, - .init_late = exynos_init_late, + .init_late = exynos_pm_init, .dt_compat = exynos_dt_compat, .dt_fixup = exynos_dt_fixup, MACHINE_END diff --git a/arch/arm/mach-exynos/include/mach/map.h b/arch/arm/mach-exynos/include/mach/map.h index 37a5ea5e2602..22ebe3654633 100644 --- a/arch/arm/mach-exynos/include/mach/map.h +++ b/arch/arm/mach-exynos/include/mach/map.h @@ -15,6 +15,4 @@ #define EXYNOS_PA_CHIPID 0x10000000 -#define EXYNOS4_PA_COREPERI 0x10500000 - #endif /* __ASM_ARCH_MAP_H */ diff --git a/arch/arm/mach-exynos/platsmp.c b/arch/arm/mach-exynos/platsmp.c index 5156fe70e030..6a1e682371b3 100644 --- a/arch/arm/mach-exynos/platsmp.c +++ b/arch/arm/mach-exynos/platsmp.c @@ -163,6 +163,26 @@ int exynos_cluster_power_state(int cluster) S5P_CORE_LOCAL_PWR_EN); } +/** + * exynos_scu_enable : enables SCU for Cortex-A9 based system + */ +void exynos_scu_enable(void) +{ + struct device_node *np; + static void __iomem *scu_base; + + if (!scu_base) { + np = of_find_compatible_node(NULL, NULL, "arm,cortex-a9-scu"); + if (np) { + scu_base = of_iomap(np, 0); + of_node_put(np); + } else { + scu_base = ioremap(scu_a9_get_base(), SZ_4K); + } + } + scu_enable(scu_base); +} + static void __iomem *cpu_boot_reg_base(void) { if (soc_is_exynos4210() && samsung_rev() == EXYNOS4210_REV_1_1) @@ -219,11 +239,6 @@ static void write_pen_release(int val) sync_cache_w(&pen_release); } -static void __iomem *scu_base_addr(void) -{ - return (void __iomem *)(S5P_VA_SCU); -} - static DEFINE_SPINLOCK(boot_lock); static void exynos_secondary_init(unsigned int cpu) @@ -389,7 +404,7 @@ static void __init exynos_smp_prepare_cpus(unsigned int max_cpus) exynos_set_delayed_reset_assertion(true); if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A9) - scu_enable(scu_base_addr()); + exynos_scu_enable(); /* * Write the address of secondary startup into the diff --git a/arch/arm/mach-exynos/pm.c b/arch/arm/mach-exynos/pm.c index a822c5073715..48e7fb38613e 100644 --- a/arch/arm/mach-exynos/pm.c +++ b/arch/arm/mach-exynos/pm.c @@ -22,8 +22,6 @@ #include <asm/suspend.h> #include <asm/cacheflush.h> -#include <mach/map.h> - #include "common.h" static inline void __iomem *exynos_boot_vector_addr(void) @@ -172,7 +170,7 @@ void exynos_enter_aftr(void) cpu_suspend(0, exynos_aftr_finisher); if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A9) { - scu_enable(S5P_VA_SCU); + exynos_scu_enable(); if (call_firmware_op(resume) == -ENOSYS) exynos_cpu_restore_register(); } diff --git a/arch/arm/mach-exynos/suspend.c b/arch/arm/mach-exynos/suspend.c index c2ed997fedef..d3db306a5a70 100644 --- a/arch/arm/mach-exynos/suspend.c +++ b/arch/arm/mach-exynos/suspend.c @@ -30,8 +30,6 @@ #include <asm/smp_scu.h> #include <asm/suspend.h> -#include <mach/map.h> - #include <plat/pm-common.h> #include "common.h" @@ -401,7 +399,7 @@ static void exynos_pm_resume(void) goto early_wakeup; if (cpuid == ARM_CPU_PART_CORTEX_A9) - scu_enable(S5P_VA_SCU); + exynos_scu_enable(); if (call_firmware_op(resume) == -ENOSYS && cpuid == ARM_CPU_PART_CORTEX_A9) diff --git a/arch/arm/mach-footbridge/dc21285.c b/arch/arm/mach-footbridge/dc21285.c index e7b350f18f5f..16d71bac0061 100644 --- a/arch/arm/mach-footbridge/dc21285.c +++ b/arch/arm/mach-footbridge/dc21285.c @@ -252,7 +252,7 @@ int __init dc21285_setup(int nr, struct pci_sys_data *sys) if (nr || !footbridge_cfn_mode()) return 0; - res = kzalloc(sizeof(struct resource) * 2, GFP_KERNEL); + res = kcalloc(2, sizeof(struct resource), GFP_KERNEL); if (!res) { printk("out of memory for root bus resources"); return 0; diff --git a/arch/arm/mach-highbank/Kconfig b/arch/arm/mach-highbank/Kconfig index 81110ec34226..5552968f07f8 100644 --- a/arch/arm/mach-highbank/Kconfig +++ b/arch/arm/mach-highbank/Kconfig @@ -1,7 +1,6 @@ config ARCH_HIGHBANK bool "Calxeda ECX-1000/2000 (Highbank/Midway)" depends on ARCH_MULTI_V7 - select ARCH_DMA_ADDR_T_64BIT if ARM_LPAE select ARCH_HAS_HOLES_MEMORYMODEL select ARCH_SUPPORTS_BIG_ENDIAN select ARM_AMBA diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index e47fa13f4b0c..6f4232384774 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -501,6 +501,7 @@ config SOC_IMX6SL config SOC_IMX6SLL bool "i.MX6 SoloLiteLite support" + select PINCTRL_IMX6SLL select SOC_IMX6 help diff --git a/arch/arm/mach-imx/mach-mx31_3ds.c b/arch/arm/mach-imx/mach-mx31_3ds.c index 68c3f0799d5b..9d87f1dcf7bb 100644 --- a/arch/arm/mach-imx/mach-mx31_3ds.c +++ b/arch/arm/mach-imx/mach-mx31_3ds.c @@ -374,26 +374,12 @@ static struct imx_ssi_platform_data mx31_3ds_ssi_pdata = { }; /* SPI */ -static int spi0_internal_chipselect[] = { - MXC_SPI_CS(0), - MXC_SPI_CS(1), - MXC_SPI_CS(2), -}; - static const struct spi_imx_master spi0_pdata __initconst = { - .chipselect = spi0_internal_chipselect, - .num_chipselect = ARRAY_SIZE(spi0_internal_chipselect), -}; - -static int spi1_internal_chipselect[] = { - MXC_SPI_CS(0), - MXC_SPI_CS(1), - MXC_SPI_CS(2), + .num_chipselect = 3, }; static const struct spi_imx_master spi1_pdata __initconst = { - .chipselect = spi1_internal_chipselect, - .num_chipselect = ARRAY_SIZE(spi1_internal_chipselect), + .num_chipselect = 3, }; static struct spi_board_info mx31_3ds_spi_devs[] __initdata = { diff --git a/arch/arm/mach-imx/mach-mx31lilly.c b/arch/arm/mach-imx/mach-mx31lilly.c index 6fd463642954..8bf52819d4d9 100644 --- a/arch/arm/mach-imx/mach-mx31lilly.c +++ b/arch/arm/mach-imx/mach-mx31lilly.c @@ -226,20 +226,12 @@ static void __init lilly1131_usb_init(void) /* SPI */ -static int spi_internal_chipselect[] = { - MXC_SPI_CS(0), - MXC_SPI_CS(1), - MXC_SPI_CS(2), -}; - static const struct spi_imx_master spi0_pdata __initconst = { - .chipselect = spi_internal_chipselect, - .num_chipselect = ARRAY_SIZE(spi_internal_chipselect), + .num_chipselect = 3, }; static const struct spi_imx_master spi1_pdata __initconst = { - .chipselect = spi_internal_chipselect, - .num_chipselect = ARRAY_SIZE(spi_internal_chipselect), + .num_chipselect = 3, }; static struct mc13xxx_platform_data mc13783_pdata __initdata = { diff --git a/arch/arm/mach-imx/mach-mx31lite.c b/arch/arm/mach-imx/mach-mx31lite.c index a3250bc7f114..a3cbba6c955b 100644 --- a/arch/arm/mach-imx/mach-mx31lite.c +++ b/arch/arm/mach-imx/mach-mx31lite.c @@ -83,15 +83,8 @@ static const struct imxuart_platform_data uart_pdata __initconst = { }; /* SPI */ -static int spi0_internal_chipselect[] = { - MXC_SPI_CS(0), - MXC_SPI_CS(1), - MXC_SPI_CS(2), -}; - static const struct spi_imx_master spi0_pdata __initconst = { - .chipselect = spi0_internal_chipselect, - .num_chipselect = ARRAY_SIZE(spi0_internal_chipselect), + .num_chipselect = 3, }; static const struct mxc_nand_platform_data @@ -133,13 +126,8 @@ static struct platform_device smsc911x_device = { * The MC13783 is the only hard-wired SPI device on the module. */ -static int spi1_internal_chipselect[] = { - MXC_SPI_CS(0), -}; - static const struct spi_imx_master spi1_pdata __initconst = { - .chipselect = spi1_internal_chipselect, - .num_chipselect = ARRAY_SIZE(spi1_internal_chipselect), + .num_chipselect = 1, }; static struct mc13xxx_platform_data mc13783_pdata __initdata = { diff --git a/arch/arm/mach-imx/mach-mx31moboard.c b/arch/arm/mach-imx/mach-mx31moboard.c index 7716f83aecdd..643a3d749703 100644 --- a/arch/arm/mach-imx/mach-mx31moboard.c +++ b/arch/arm/mach-imx/mach-mx31moboard.c @@ -152,14 +152,8 @@ static const struct imxi2c_platform_data moboard_i2c1_data __initconst = { .bitrate = 100000, }; -static int moboard_spi1_cs[] = { - MXC_SPI_CS(0), - MXC_SPI_CS(2), -}; - static const struct spi_imx_master moboard_spi1_pdata __initconst = { - .chipselect = moboard_spi1_cs, - .num_chipselect = ARRAY_SIZE(moboard_spi1_cs), + .num_chipselect = 3, }; static struct regulator_consumer_supply sdhc_consumers[] = { @@ -296,19 +290,14 @@ static struct spi_board_info moboard_spi_board_info[] __initdata = { /* irq number is run-time assigned */ .max_speed_hz = 300000, .bus_num = 1, - .chip_select = 1, + .chip_select = 0, .platform_data = &moboard_pmic, .mode = SPI_CS_HIGH, }, }; -static int moboard_spi2_cs[] = { - MXC_SPI_CS(0), MXC_SPI_CS(1), -}; - static const struct spi_imx_master moboard_spi2_pdata __initconst = { - .chipselect = moboard_spi2_cs, - .num_chipselect = ARRAY_SIZE(moboard_spi2_cs), + .num_chipselect = 2, }; #define SDHC1_CD IOMUX_TO_GPIO(MX31_PIN_ATA_CS0) diff --git a/arch/arm/mach-imx/mach-pca100.c b/arch/arm/mach-imx/mach-pca100.c index ed675863655b..5714e2f1b106 100644 --- a/arch/arm/mach-imx/mach-pca100.c +++ b/arch/arm/mach-imx/mach-pca100.c @@ -20,7 +20,7 @@ #include <linux/platform_device.h> #include <linux/io.h> #include <linux/i2c.h> -#include <linux/platform_data/at24.h> +#include <linux/property.h> #include <linux/dma-mapping.h> #include <linux/spi/spi.h> #include <linux/spi/eeprom.h> @@ -168,16 +168,15 @@ static const struct imxi2c_platform_data pca100_i2c1_data __initconst = { .bitrate = 100000, }; -static struct at24_platform_data board_eeprom = { - .byte_len = 4096, - .page_size = 32, - .flags = AT24_FLAG_ADDR16, +static const struct property_entry board_eeprom_properties[] = { + PROPERTY_ENTRY_U32("pagesize", 32), + { } }; static struct i2c_board_info pca100_i2c_devices[] = { { - I2C_BOARD_INFO("at24", 0x52), /* E0=0, E1=1, E2=0 */ - .platform_data = &board_eeprom, + I2C_BOARD_INFO("24c32", 0x52), /* E0=0, E1=1, E2=0 */ + .properties = board_eeprom_properties, }, { I2C_BOARD_INFO("pcf8563", 0x51), }, { diff --git a/arch/arm/mach-imx/mach-pcm037.c b/arch/arm/mach-imx/mach-pcm037.c index b787ba6897e4..004737c40fda 100644 --- a/arch/arm/mach-imx/mach-pcm037.c +++ b/arch/arm/mach-imx/mach-pcm037.c @@ -23,7 +23,7 @@ #include <linux/smsc911x.h> #include <linux/interrupt.h> #include <linux/i2c.h> -#include <linux/platform_data/at24.h> +#include <linux/property.h> #include <linux/delay.h> #include <linux/spi/spi.h> #include <linux/irq.h> @@ -263,16 +263,15 @@ static const struct imxi2c_platform_data pcm037_i2c2_data __initconst = { .bitrate = 20000, }; -static struct at24_platform_data board_eeprom = { - .byte_len = 4096, - .page_size = 32, - .flags = AT24_FLAG_ADDR16, +static const struct property_entry board_eeprom_properties[] = { + PROPERTY_ENTRY_U32("pagesize", 32), + { } }; static struct i2c_board_info pcm037_i2c_devices[] = { { - I2C_BOARD_INFO("at24", 0x52), /* E0=0, E1=1, E2=0 */ - .platform_data = &board_eeprom, + I2C_BOARD_INFO("24c32", 0x52), /* E0=0, E1=1, E2=0 */ + .properties = board_eeprom_properties, }, { I2C_BOARD_INFO("pcf8563", 0x51), } diff --git a/arch/arm/mach-imx/mach-pcm037_eet.c b/arch/arm/mach-imx/mach-pcm037_eet.c index 95bd97710494..15bc956d466b 100644 --- a/arch/arm/mach-imx/mach-pcm037_eet.c +++ b/arch/arm/mach-imx/mach-pcm037_eet.c @@ -56,11 +56,8 @@ static struct spi_board_info pcm037_spi_dev[] = { }; /* Platform Data for MXC CSPI */ -static int pcm037_spi1_cs[] = { MXC_SPI_CS(0), MXC_SPI_CS(1), }; - static const struct spi_imx_master pcm037_spi1_pdata __initconst = { - .chipselect = pcm037_spi1_cs, - .num_chipselect = ARRAY_SIZE(pcm037_spi1_cs), + .num_chipselect = 2, }; /* GPIO-keys input device */ diff --git a/arch/arm/mach-imx/mach-pcm043.c b/arch/arm/mach-imx/mach-pcm043.c index 78e2bf8dcd96..e595e5368676 100644 --- a/arch/arm/mach-imx/mach-pcm043.c +++ b/arch/arm/mach-imx/mach-pcm043.c @@ -24,7 +24,7 @@ #include <linux/interrupt.h> #include <linux/delay.h> #include <linux/i2c.h> -#include <linux/platform_data/at24.h> +#include <linux/property.h> #include <linux/usb/otg.h> #include <linux/usb/ulpi.h> @@ -110,16 +110,15 @@ static const struct imxi2c_platform_data pcm043_i2c0_data __initconst = { .bitrate = 50000, }; -static struct at24_platform_data board_eeprom = { - .byte_len = 4096, - .page_size = 32, - .flags = AT24_FLAG_ADDR16, +static const struct property_entry board_eeprom_properties[] = { + PROPERTY_ENTRY_U32("pagesize", 32), + { } }; static struct i2c_board_info pcm043_i2c_devices[] = { { - I2C_BOARD_INFO("at24", 0x52), /* E0=0, E1=1, E2=0 */ - .platform_data = &board_eeprom, + I2C_BOARD_INFO("24c32", 0x52), /* E0=0, E1=1, E2=0 */ + .properties = board_eeprom_properties, }, { I2C_BOARD_INFO("pcf8563", 0x51), }, diff --git a/arch/arm/mach-imx/mach-vpr200.c b/arch/arm/mach-imx/mach-vpr200.c index 5ff154c9a086..da3336aaa4c5 100644 --- a/arch/arm/mach-imx/mach-vpr200.c +++ b/arch/arm/mach-imx/mach-vpr200.c @@ -29,7 +29,6 @@ #include <asm/mach/time.h> #include <linux/i2c.h> -#include <linux/platform_data/at24.h> #include <linux/mfd/mc13xxx.h> #include "common.h" @@ -145,15 +144,9 @@ static const struct imxi2c_platform_data vpr200_i2c0_data __initconst = { .bitrate = 50000, }; -static struct at24_platform_data vpr200_eeprom = { - .byte_len = 2048 / 8, - .page_size = 1, -}; - static struct i2c_board_info vpr200_i2c_devices[] = { { - I2C_BOARD_INFO("at24", 0x50), /* E0=0, E1=0, E2=0 */ - .platform_data = &vpr200_eeprom, + I2C_BOARD_INFO("24c02", 0x50), /* E0=0, E1=0, E2=0 */ }, { I2C_BOARD_INFO("mc13892", 0x08), .platform_data = &vpr200_pmic, diff --git a/arch/arm/mach-ixp4xx/avila-setup.c b/arch/arm/mach-ixp4xx/avila-setup.c index 77def6169f50..44cbbce6bda6 100644 --- a/arch/arm/mach-ixp4xx/avila-setup.c +++ b/arch/arm/mach-ixp4xx/avila-setup.c @@ -51,7 +51,7 @@ static struct platform_device avila_flash = { }; static struct gpiod_lookup_table avila_i2c_gpiod_table = { - .dev_id = "i2c-gpio", + .dev_id = "i2c-gpio.0", .table = { GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", AVILA_SDA_PIN, NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), diff --git a/arch/arm/mach-ixp4xx/common-pci.c b/arch/arm/mach-ixp4xx/common-pci.c index bcf3df59f71b..6835b17113e5 100644 --- a/arch/arm/mach-ixp4xx/common-pci.c +++ b/arch/arm/mach-ixp4xx/common-pci.c @@ -421,7 +421,7 @@ int ixp4xx_setup(int nr, struct pci_sys_data *sys) if (nr >= 1) return 0; - res = kzalloc(sizeof(*res) * 2, GFP_KERNEL); + res = kcalloc(2, sizeof(*res), GFP_KERNEL); if (res == NULL) { /* * If we're out of memory this early, something is wrong, diff --git a/arch/arm/mach-ixp4xx/dsmg600-setup.c b/arch/arm/mach-ixp4xx/dsmg600-setup.c index 0f5c99941a7d..397190f3a8da 100644 --- a/arch/arm/mach-ixp4xx/dsmg600-setup.c +++ b/arch/arm/mach-ixp4xx/dsmg600-setup.c @@ -70,7 +70,7 @@ static struct platform_device dsmg600_flash = { }; static struct gpiod_lookup_table dsmg600_i2c_gpiod_table = { - .dev_id = "i2c-gpio", + .dev_id = "i2c-gpio.0", .table = { GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", DSMG600_SDA_PIN, NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), diff --git a/arch/arm/mach-ixp4xx/fsg-setup.c b/arch/arm/mach-ixp4xx/fsg-setup.c index 033f79b35d51..f0a152e365b1 100644 --- a/arch/arm/mach-ixp4xx/fsg-setup.c +++ b/arch/arm/mach-ixp4xx/fsg-setup.c @@ -56,7 +56,7 @@ static struct platform_device fsg_flash = { }; static struct gpiod_lookup_table fsg_i2c_gpiod_table = { - .dev_id = "i2c-gpio", + .dev_id = "i2c-gpio.0", .table = { GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", FSG_SDA_PIN, NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), diff --git a/arch/arm/mach-ixp4xx/ixdp425-setup.c b/arch/arm/mach-ixp4xx/ixdp425-setup.c index b168e2fbdbeb..3ec829d52cdd 100644 --- a/arch/arm/mach-ixp4xx/ixdp425-setup.c +++ b/arch/arm/mach-ixp4xx/ixdp425-setup.c @@ -124,7 +124,7 @@ static struct platform_device ixdp425_flash_nand = { #endif /* CONFIG_MTD_NAND_PLATFORM */ static struct gpiod_lookup_table ixdp425_i2c_gpiod_table = { - .dev_id = "i2c-gpio", + .dev_id = "i2c-gpio.0", .table = { GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", IXDP425_SDA_PIN, NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), diff --git a/arch/arm/mach-ixp4xx/nas100d-setup.c b/arch/arm/mach-ixp4xx/nas100d-setup.c index 76dfff03cb71..4138d6aa4c52 100644 --- a/arch/arm/mach-ixp4xx/nas100d-setup.c +++ b/arch/arm/mach-ixp4xx/nas100d-setup.c @@ -102,7 +102,7 @@ static struct platform_device nas100d_leds = { }; static struct gpiod_lookup_table nas100d_i2c_gpiod_table = { - .dev_id = "i2c-gpio", + .dev_id = "i2c-gpio.0", .table = { GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", NAS100D_SDA_PIN, NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), diff --git a/arch/arm/mach-ixp4xx/nslu2-setup.c b/arch/arm/mach-ixp4xx/nslu2-setup.c index 91da63a7d7b5..341b263482ef 100644 --- a/arch/arm/mach-ixp4xx/nslu2-setup.c +++ b/arch/arm/mach-ixp4xx/nslu2-setup.c @@ -70,7 +70,7 @@ static struct platform_device nslu2_flash = { }; static struct gpiod_lookup_table nslu2_i2c_gpiod_table = { - .dev_id = "i2c-gpio", + .dev_id = "i2c-gpio.0", .table = { GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", NSLU2_SDA_PIN, NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), diff --git a/arch/arm/mach-keystone/pm_domain.c b/arch/arm/mach-keystone/pm_domain.c index fe57e2692629..abca83d22ff3 100644 --- a/arch/arm/mach-keystone/pm_domain.c +++ b/arch/arm/mach-keystone/pm_domain.c @@ -29,6 +29,7 @@ static struct dev_pm_domain keystone_pm_domain = { static struct pm_clk_notifier_block platform_domain_notifier = { .pm_domain = &keystone_pm_domain, + .con_ids = { NULL }, }; static const struct of_device_id of_keystone_table[] = { diff --git a/arch/arm/mach-ks8695/board-acs5k.c b/arch/arm/mach-ks8695/board-acs5k.c index 937eb1d47e7b..ef835d82cdb9 100644 --- a/arch/arm/mach-ks8695/board-acs5k.c +++ b/arch/arm/mach-ks8695/board-acs5k.c @@ -19,7 +19,7 @@ #include <linux/gpio/machine.h> #include <linux/i2c.h> #include <linux/i2c-algo-bit.h> -#include <linux/i2c-gpio.h> +#include <linux/platform_data/i2c-gpio.h> #include <linux/platform_data/pca953x.h> #include <linux/mtd/mtd.h> diff --git a/arch/arm/mach-meson/Kconfig b/arch/arm/mach-meson/Kconfig index d90f61e6254f..d51cfda953d4 100644 --- a/arch/arm/mach-meson/Kconfig +++ b/arch/arm/mach-meson/Kconfig @@ -19,14 +19,7 @@ config MACH_MESON6 select MESON6_TIMER config MACH_MESON8 - bool "Amlogic Meson8 SoCs support" - default ARCH_MESON - select MESON6_TIMER - select COMMON_CLK_MESON8B - select MESON_IRQ_GPIO - -config MACH_MESON8B - bool "Amlogic Meson8b SoCs support" + bool "Amlogic Meson8, Meson8b and Meson8m2 SoCs support" default ARCH_MESON select MESON6_TIMER select COMMON_CLK_MESON8B diff --git a/arch/arm/mach-meson/meson.c b/arch/arm/mach-meson/meson.c index 4e2357178625..c8d99df32f9b 100644 --- a/arch/arm/mach-meson/meson.c +++ b/arch/arm/mach-meson/meson.c @@ -20,6 +20,7 @@ static const char * const meson_common_board_compat[] = { "amlogic,meson6", "amlogic,meson8", "amlogic,meson8b", + "amlogic,meson8m2", NULL, }; diff --git a/arch/arm/mach-omap1/ams-delta-fiq.c b/arch/arm/mach-omap1/ams-delta-fiq.c index 793a24a53c52..d7ca9e2b40d2 100644 --- a/arch/arm/mach-omap1/ams-delta-fiq.c +++ b/arch/arm/mach-omap1/ams-delta-fiq.c @@ -58,22 +58,24 @@ static irqreturn_t deferred_fiq(int irq, void *dev_id) irq_num = gpio_to_irq(gpio); fiq_count = fiq_buffer[FIQ_CNT_INT_00 + gpio]; - while (irq_counter[gpio] < fiq_count) { - if (gpio != AMS_DELTA_GPIO_PIN_KEYBRD_CLK) { - struct irq_data *d = irq_get_irq_data(irq_num); - - /* - * It looks like handle_edge_irq() that - * OMAP GPIO edge interrupts default to, - * expects interrupt already unmasked. - */ - if (irq_chip && irq_chip->irq_unmask) + if (irq_counter[gpio] < fiq_count && + gpio != AMS_DELTA_GPIO_PIN_KEYBRD_CLK) { + struct irq_data *d = irq_get_irq_data(irq_num); + + /* + * handle_simple_irq() that OMAP GPIO edge + * interrupts default to since commit 80ac93c27441 + * requires interrupt already acked and unmasked. + */ + if (irq_chip) { + if (irq_chip->irq_ack) + irq_chip->irq_ack(d); + if (irq_chip->irq_unmask) irq_chip->irq_unmask(d); } - generic_handle_irq(irq_num); - - irq_counter[gpio]++; } + for (; irq_counter[gpio] < fiq_count; irq_counter[gpio]++) + generic_handle_irq(irq_num); } return IRQ_HANDLED; } diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c index 52e8e53ca154..80f54cb54276 100644 --- a/arch/arm/mach-omap1/board-ams-delta.c +++ b/arch/arm/mach-omap1/board-ams-delta.c @@ -12,6 +12,7 @@ * published by the Free Software Foundation. */ #include <linux/gpio/driver.h> +#include <linux/gpio/machine.h> #include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> @@ -202,7 +203,10 @@ static struct resource latch2_resources[] = { }, }; +#define LATCH2_LABEL "latch2" + static struct bgpio_pdata latch2_pdata = { + .label = LATCH2_LABEL, .base = AMS_DELTA_LATCH2_GPIO_BASE, .ngpio = AMS_DELTA_LATCH2_NGPIO, }; @@ -217,6 +221,23 @@ static struct platform_device latch2_gpio_device = { }, }; +#define LATCH2_PIN_LCD_VBLEN 0 +#define LATCH2_PIN_LCD_NDISP 1 +#define LATCH2_PIN_NAND_NCE 2 +#define LATCH2_PIN_NAND_NRE 3 +#define LATCH2_PIN_NAND_NWP 4 +#define LATCH2_PIN_NAND_NWE 5 +#define LATCH2_PIN_NAND_ALE 6 +#define LATCH2_PIN_NAND_CLE 7 +#define LATCH2_PIN_KEYBRD_PWR 8 +#define LATCH2_PIN_KEYBRD_DATAOUT 9 +#define LATCH2_PIN_SCARD_RSTIN 10 +#define LATCH2_PIN_SCARD_CMDVCC 11 +#define LATCH2_PIN_MODEM_NRESET 12 +#define LATCH2_PIN_MODEM_CODEC 13 +#define LATCH2_PIN_HOOKFLASH1 14 +#define LATCH2_PIN_HOOKFLASH2 15 + static const struct gpio latch_gpios[] __initconst = { { .gpio = LATCH1_GPIO_BASE + 6, @@ -239,11 +260,6 @@ static const struct gpio latch_gpios[] __initconst = { .label = "scard_cmdvcc", }, { - .gpio = AMS_DELTA_GPIO_PIN_MODEM_CODEC, - .flags = GPIOF_OUT_INIT_LOW, - .label = "modem_codec", - }, - { .gpio = AMS_DELTA_LATCH2_GPIO_BASE + 14, .flags = GPIOF_OUT_INIT_LOW, .label = "hookflash1", @@ -323,6 +339,22 @@ static struct platform_device ams_delta_nand_device = { .resource = ams_delta_nand_resources, }; +#define OMAP_GPIO_LABEL "gpio-0-15" + +static struct gpiod_lookup_table ams_delta_nand_gpio_table = { + .table = { + GPIO_LOOKUP(OMAP_GPIO_LABEL, AMS_DELTA_GPIO_PIN_NAND_RB, "rdy", + 0), + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_NAND_NCE, "nce", 0), + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_NAND_NRE, "nre", 0), + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_NAND_NWP, "nwp", 0), + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_NAND_NWE, "nwe", 0), + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_NAND_ALE, "ale", 0), + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_NAND_CLE, "cle", 0), + { }, + }, +}; + static struct resource ams_delta_kp_resources[] = { [0] = { .start = INT_KEYBOARD, @@ -358,6 +390,14 @@ static struct platform_device ams_delta_lcd_device = { .id = -1, }; +static struct gpiod_lookup_table ams_delta_lcd_gpio_table = { + .table = { + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_LCD_VBLEN, "vblen", 0), + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_LCD_NDISP, "ndisp", 0), + { }, + }, +}; + static const struct gpio_led gpio_leds[] __initconst = { { .name = "camera", @@ -449,11 +489,35 @@ static struct platform_device ams_delta_audio_device = { .id = -1, }; +static struct gpiod_lookup_table ams_delta_audio_gpio_table = { + .table = { + GPIO_LOOKUP(OMAP_GPIO_LABEL, AMS_DELTA_GPIO_PIN_HOOK_SWITCH, + "hook_switch", 0), + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_MODEM_CODEC, + "modem_codec", 0), + { }, + }, +}; + static struct platform_device cx20442_codec_device = { .name = "cx20442-codec", .id = -1, }; +static struct gpiod_lookup_table ams_delta_serio_gpio_table = { + .table = { + GPIO_LOOKUP(OMAP_GPIO_LABEL, AMS_DELTA_GPIO_PIN_KEYBRD_DATA, + "data", 0), + GPIO_LOOKUP(OMAP_GPIO_LABEL, AMS_DELTA_GPIO_PIN_KEYBRD_CLK, + "clock", 0), + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_KEYBRD_PWR, + "power", 0), + GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_KEYBRD_DATAOUT, + "dataout", 0), + { }, + }, +}; + static struct platform_device *ams_delta_devices[] __initdata = { &latch1_gpio_device, &latch2_gpio_device, @@ -468,6 +532,16 @@ static struct platform_device *late_devices[] __initdata = { &cx20442_codec_device, }; +static struct gpiod_lookup_table *ams_delta_gpio_tables[] __initdata = { + &ams_delta_audio_gpio_table, + &ams_delta_serio_gpio_table, +}; + +static struct gpiod_lookup_table *late_gpio_tables[] __initdata = { + &ams_delta_lcd_gpio_table, + &ams_delta_nand_gpio_table, +}; + static void __init ams_delta_init(void) { /* mux pins for uarts */ @@ -500,6 +574,20 @@ static void __init ams_delta_init(void) gpio_led_register_device(-1, &leds_pdata); platform_add_devices(ams_delta_devices, ARRAY_SIZE(ams_delta_devices)); + /* + * As soon as devices have been registered, assign their dev_names + * to respective GPIO lookup tables before they are added. + */ + ams_delta_audio_gpio_table.dev_id = + dev_name(&ams_delta_audio_device.dev); + /* + * No device name is assigned to GPIO lookup table for serio device + * as long as serio driver is not converted to platform device driver. + */ + + gpiod_add_lookup_tables(ams_delta_gpio_tables, + ARRAY_SIZE(ams_delta_gpio_tables)); + ams_delta_init_fiq(); omap_writew(omap_readw(ARM_RSTCT1) | 0x0004, ARM_RSTCT1); @@ -570,6 +658,15 @@ static int __init late_init(void) platform_add_devices(late_devices, ARRAY_SIZE(late_devices)); + /* + * As soon as devices have been registered, assign their dev_names + * to respective GPIO lookup tables before they are added. + */ + ams_delta_lcd_gpio_table.dev_id = dev_name(&ams_delta_lcd_device.dev); + ams_delta_nand_gpio_table.dev_id = dev_name(&ams_delta_nand_device.dev); + + gpiod_add_lookup_tables(late_gpio_tables, ARRAY_SIZE(late_gpio_tables)); + err = platform_device_register(&modem_nreset_device); if (err) { pr_err("Couldn't register the modem regulator device\n"); diff --git a/arch/arm/mach-omap1/board-htcherald.c b/arch/arm/mach-omap1/board-htcherald.c index 67d46690a56e..da8f3fc3180f 100644 --- a/arch/arm/mach-omap1/board-htcherald.c +++ b/arch/arm/mach-omap1/board-htcherald.c @@ -31,7 +31,7 @@ #include <linux/gpio.h> #include <linux/gpio_keys.h> #include <linux/i2c.h> -#include <linux/i2c-gpio.h> +#include <linux/platform_data/i2c-gpio.h> #include <linux/htcpld.h> #include <linux/leds.h> #include <linux/spi/spi.h> diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c index c66372ed29e2..9ffa8d755a59 100644 --- a/arch/arm/mach-omap1/board-osk.c +++ b/arch/arm/mach-omap1/board-osk.c @@ -303,22 +303,22 @@ static const struct omap_lcd_config osk_lcd_config __initconst = { #ifdef CONFIG_OMAP_OSK_MISTRAL #include <linux/input.h> -#include <linux/platform_data/at24.h> +#include <linux/property.h> #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> #include <linux/platform_data/keypad-omap.h> -static struct at24_platform_data at24c04 = { - .byte_len = SZ_4K / 8, - .page_size = 16, +static const struct property_entry mistral_at24_properties[] = { + PROPERTY_ENTRY_U32("pagesize", 16), + { } }; static struct i2c_board_info __initdata mistral_i2c_board_info[] = { { /* NOTE: powered from LCD supply */ I2C_BOARD_INFO("24c04", 0x50), - .platform_data = &at24c04, + .properties = mistral_at24_properties, }, /* TODO when driver support is ready: * - optionally ov9640 camera sensor at 0x30 diff --git a/arch/arm/mach-omap1/common.h b/arch/arm/mach-omap1/common.h index d83ff257eaa8..c6537d2c2859 100644 --- a/arch/arm/mach-omap1/common.h +++ b/arch/arm/mach-omap1/common.h @@ -27,7 +27,7 @@ #define __ARCH_ARM_MACH_OMAP1_COMMON_H #include <linux/mtd/mtd.h> -#include <linux/i2c-omap.h> +#include <linux/platform_data/i2c-omap.h> #include <linux/reboot.h> #include <asm/exception.h> diff --git a/arch/arm/mach-omap1/i2c.c b/arch/arm/mach-omap1/i2c.c index 5bdf3c4190f9..9250f263ac51 100644 --- a/arch/arm/mach-omap1/i2c.c +++ b/arch/arm/mach-omap1/i2c.c @@ -20,7 +20,7 @@ */ #include <linux/i2c.h> -#include <linux/i2c-omap.h> +#include <linux/platform_data/i2c-omap.h> #include <mach/mux.h> #include "soc.h" diff --git a/arch/arm/mach-omap1/mcbsp.c b/arch/arm/mach-omap1/mcbsp.c index 8ed67f8d1762..27e22e702f96 100644 --- a/arch/arm/mach-omap1/mcbsp.c +++ b/arch/arm/mach-omap1/mcbsp.c @@ -389,7 +389,7 @@ static void omap_mcbsp_register_board_cfg(struct resource *res, int res_count, { int i; - omap_mcbsp_devices = kzalloc(size * sizeof(struct platform_device *), + omap_mcbsp_devices = kcalloc(size, sizeof(struct platform_device *), GFP_KERNEL); if (!omap_mcbsp_devices) { printk(KERN_ERR "Could not register McBSP devices\n"); diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 0d9ce58bc464..01377c292db4 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -78,7 +78,6 @@ endif omap-4-5-pm-common = omap-mpuss-lowpower.o obj-$(CONFIG_ARCH_OMAP4) += $(omap-4-5-pm-common) obj-$(CONFIG_SOC_OMAP5) += $(omap-4-5-pm-common) -obj-$(CONFIG_OMAP_PM_NOOP) += omap-pm-noop.o ifeq ($(CONFIG_PM),y) obj-$(CONFIG_ARCH_OMAP2) += pm24xx.o diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 6c61ecc62905..6b4f4975cf7a 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -31,8 +31,6 @@ static const struct of_device_id omap_dt_match_table[] __initconst = { static void __init __maybe_unused omap_generic_init(void) { pdata_quirks_init(omap_dt_match_table); - - omapdss_init_of(); omap_soc_device_init(); } diff --git a/arch/arm/mach-omap2/clockdomain.c b/arch/arm/mach-omap2/clockdomain.c index b79b1ca9aee9..6d44fe05a3fe 100644 --- a/arch/arm/mach-omap2/clockdomain.c +++ b/arch/arm/mach-omap2/clockdomain.c @@ -23,6 +23,7 @@ #include <linux/limits.h> #include <linux/err.h> #include <linux/clk-provider.h> +#include <linux/cpu_pm.h> #include <linux/io.h> @@ -31,6 +32,7 @@ #include "soc.h" #include "clock.h" #include "clockdomain.h" +#include "pm.h" /* clkdm_list contains all registered struct clockdomains */ static LIST_HEAD(clkdm_list); @@ -39,6 +41,8 @@ static LIST_HEAD(clkdm_list); static struct clkdm_autodep *autodeps; static struct clkdm_ops *arch_clkdm; +void clkdm_save_context(void); +void clkdm_restore_context(void); /* Private functions */ @@ -449,6 +453,22 @@ int clkdm_register_autodeps(struct clkdm_autodep *ia) return 0; } +static int cpu_notifier(struct notifier_block *nb, unsigned long cmd, void *v) +{ + switch (cmd) { + case CPU_CLUSTER_PM_ENTER: + if (enable_off_mode) + clkdm_save_context(); + break; + case CPU_CLUSTER_PM_EXIT: + if (enable_off_mode) + clkdm_restore_context(); + break; + } + + return NOTIFY_OK; +} + /** * clkdm_complete_init - set up the clockdomain layer * @@ -460,6 +480,7 @@ int clkdm_register_autodeps(struct clkdm_autodep *ia) int clkdm_complete_init(void) { struct clockdomain *clkdm; + static struct notifier_block nb; if (list_empty(&clkdm_list)) return -EACCES; @@ -474,6 +495,12 @@ int clkdm_complete_init(void) clkdm_clear_all_sleepdeps(clkdm); } + /* Only AM43XX can lose clkdm context during rtc-ddr suspend */ + if (soc_is_am43xx()) { + nb.notifier_call = cpu_notifier; + cpu_pm_register_notifier(&nb); + } + return 0; } @@ -1307,3 +1334,49 @@ int clkdm_hwmod_disable(struct clockdomain *clkdm, struct omap_hwmod *oh) return 0; } +/** + * _clkdm_save_context - save the context for the control of this clkdm + * + * Due to a suspend or hibernation operation, the state of the registers + * controlling this clkdm will be lost, save their context. + */ +static int _clkdm_save_context(struct clockdomain *clkdm, void *ununsed) +{ + if (!arch_clkdm || !arch_clkdm->clkdm_save_context) + return -EINVAL; + + return arch_clkdm->clkdm_save_context(clkdm); +} + +/** + * _clkdm_restore_context - restore context for control of this clkdm + * + * Restore the register values for this clockdomain. + */ +static int _clkdm_restore_context(struct clockdomain *clkdm, void *ununsed) +{ + if (!arch_clkdm || !arch_clkdm->clkdm_restore_context) + return -EINVAL; + + return arch_clkdm->clkdm_restore_context(clkdm); +} + +/** + * clkdm_save_context - Saves the context for each registered clkdm + * + * Save the context for each registered clockdomain. + */ +void clkdm_save_context(void) +{ + clkdm_for_each(_clkdm_save_context, NULL); +} + +/** + * clkdm_restore_context - Restores the context for each registered clkdm + * + * Restore the context for each registered clockdomain. + */ +void clkdm_restore_context(void) +{ + clkdm_for_each(_clkdm_restore_context, NULL); +} diff --git a/arch/arm/mach-omap2/clockdomain.h b/arch/arm/mach-omap2/clockdomain.h index 24667a5a9dc0..c7d0953e4aa2 100644 --- a/arch/arm/mach-omap2/clockdomain.h +++ b/arch/arm/mach-omap2/clockdomain.h @@ -141,6 +141,7 @@ struct clockdomain { int usecount; int forcewake_count; struct list_head node; + u32 context; }; /** @@ -159,6 +160,8 @@ struct clockdomain { * @clkdm_deny_idle: Disable hw supervised idle transitions for clock domain * @clkdm_clk_enable: Put the clkdm in right state for a clock enable * @clkdm_clk_disable: Put the clkdm in right state for a clock disable + * @clkdm_save_context: Save the current clkdm context + * @clkdm_restore_context: Restore the clkdm context */ struct clkdm_ops { int (*clkdm_add_wkdep)(struct clockdomain *clkdm1, struct clockdomain *clkdm2); @@ -175,6 +178,8 @@ struct clkdm_ops { void (*clkdm_deny_idle)(struct clockdomain *clkdm); int (*clkdm_clk_enable)(struct clockdomain *clkdm); int (*clkdm_clk_disable)(struct clockdomain *clkdm); + int (*clkdm_save_context)(struct clockdomain *clkdm); + int (*clkdm_restore_context)(struct clockdomain *clkdm); }; int clkdm_register_platform_funcs(struct clkdm_ops *co); @@ -214,6 +219,9 @@ int clkdm_clk_disable(struct clockdomain *clkdm, struct clk *clk); int clkdm_hwmod_enable(struct clockdomain *clkdm, struct omap_hwmod *oh); int clkdm_hwmod_disable(struct clockdomain *clkdm, struct omap_hwmod *oh); +void clkdm_save_context(void); +void clkdm_restore_context(void); + extern void __init omap242x_clockdomains_init(void); extern void __init omap243x_clockdomains_init(void); extern void __init omap3xxx_clockdomains_init(void); diff --git a/arch/arm/mach-omap2/cm33xx.c b/arch/arm/mach-omap2/cm33xx.c index 1cc0247a2cb5..084d454f6074 100644 --- a/arch/arm/mach-omap2/cm33xx.c +++ b/arch/arm/mach-omap2/cm33xx.c @@ -72,6 +72,17 @@ static inline u32 am33xx_cm_rmw_reg_bits(u32 mask, u32 bits, s16 inst, s16 idx) return v; } +static inline u32 am33xx_cm_read_reg_bits(u16 inst, s16 idx, u32 mask) +{ + u32 v; + + v = am33xx_cm_read_reg(inst, idx); + v &= mask; + v >>= __ffs(mask); + + return v; +} + /** * _clkctrl_idlest - read a CM_*_CLKCTRL register; mask & shift IDLEST bitfield * @inst: CM instance register offset (*_INST macro) @@ -338,6 +349,46 @@ static u32 am33xx_cm_xlate_clkctrl(u8 part, u16 inst, u16 offset) return cm_base.pa + inst + offset; } +/** + * am33xx_clkdm_save_context - Save the clockdomain transition context + * @clkdm: The clockdomain pointer whose context needs to be saved + * + * Save the clockdomain transition context. + */ +static int am33xx_clkdm_save_context(struct clockdomain *clkdm) +{ + clkdm->context = am33xx_cm_read_reg_bits(clkdm->cm_inst, + clkdm->clkdm_offs, + AM33XX_CLKTRCTRL_MASK); + + return 0; +} + +/** + * am33xx_restore_save_context - Restore the clockdomain transition context + * @clkdm: The clockdomain pointer whose context needs to be restored + * + * Restore the clockdomain transition context. + */ +static int am33xx_clkdm_restore_context(struct clockdomain *clkdm) +{ + switch (clkdm->context) { + case OMAP34XX_CLKSTCTRL_DISABLE_AUTO: + am33xx_clkdm_deny_idle(clkdm); + break; + case OMAP34XX_CLKSTCTRL_FORCE_SLEEP: + am33xx_clkdm_sleep(clkdm); + break; + case OMAP34XX_CLKSTCTRL_FORCE_WAKEUP: + am33xx_clkdm_wakeup(clkdm); + break; + case OMAP34XX_CLKSTCTRL_ENABLE_AUTO: + am33xx_clkdm_allow_idle(clkdm); + break; + } + return 0; +} + struct clkdm_ops am33xx_clkdm_operations = { .clkdm_sleep = am33xx_clkdm_sleep, .clkdm_wakeup = am33xx_clkdm_wakeup, @@ -345,6 +396,8 @@ struct clkdm_ops am33xx_clkdm_operations = { .clkdm_deny_idle = am33xx_clkdm_deny_idle, .clkdm_clk_enable = am33xx_clkdm_clk_enable, .clkdm_clk_disable = am33xx_clkdm_clk_disable, + .clkdm_save_context = am33xx_clkdm_save_context, + .clkdm_restore_context = am33xx_clkdm_restore_context, }; static const struct cm_ll_data am33xx_cm_ll_data = { diff --git a/arch/arm/mach-omap2/cminst44xx.c b/arch/arm/mach-omap2/cminst44xx.c index 7deefee49fc3..c11ac492b626 100644 --- a/arch/arm/mach-omap2/cminst44xx.c +++ b/arch/arm/mach-omap2/cminst44xx.c @@ -481,6 +481,47 @@ static u32 omap4_cminst_xlate_clkctrl(u8 part, u16 inst, u16 offset) return _cm_bases[part].pa + inst + offset; } +/** + * omap4_clkdm_save_context - Save the clockdomain modulemode context + * @clkdm: The clockdomain pointer whose context needs to be saved + * + * Save the clockdomain modulemode context. + */ +static int omap4_clkdm_save_context(struct clockdomain *clkdm) +{ + clkdm->context = omap4_cminst_read_inst_reg(clkdm->prcm_partition, + clkdm->cm_inst, + clkdm->clkdm_offs + + OMAP4_CM_CLKSTCTRL); + clkdm->context &= OMAP4430_MODULEMODE_MASK; + return 0; +} + +/** + * omap4_clkdm_restore_context - Restore the clockdomain modulemode context + * @clkdm: The clockdomain pointer whose context needs to be restored + * + * Restore the clockdomain modulemode context. + */ +static int omap4_clkdm_restore_context(struct clockdomain *clkdm) +{ + switch (clkdm->context) { + case OMAP34XX_CLKSTCTRL_DISABLE_AUTO: + omap4_clkdm_deny_idle(clkdm); + break; + case OMAP34XX_CLKSTCTRL_FORCE_SLEEP: + omap4_clkdm_sleep(clkdm); + break; + case OMAP34XX_CLKSTCTRL_FORCE_WAKEUP: + omap4_clkdm_wakeup(clkdm); + break; + case OMAP34XX_CLKSTCTRL_ENABLE_AUTO: + omap4_clkdm_allow_idle(clkdm); + break; + } + return 0; +} + struct clkdm_ops omap4_clkdm_operations = { .clkdm_add_wkdep = omap4_clkdm_add_wkup_sleep_dep, .clkdm_del_wkdep = omap4_clkdm_del_wkup_sleep_dep, @@ -496,6 +537,8 @@ struct clkdm_ops omap4_clkdm_operations = { .clkdm_deny_idle = omap4_clkdm_deny_idle, .clkdm_clk_enable = omap4_clkdm_clk_enable, .clkdm_clk_disable = omap4_clkdm_clk_disable, + .clkdm_save_context = omap4_clkdm_save_context, + .clkdm_restore_context = omap4_clkdm_restore_context, }; struct clkdm_ops am43xx_clkdm_operations = { diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h index fbe0b78bf489..129455e822e4 100644 --- a/arch/arm/mach-omap2/common.h +++ b/arch/arm/mach-omap2/common.h @@ -30,7 +30,7 @@ #include <linux/delay.h> #include <linux/i2c.h> #include <linux/mfd/twl.h> -#include <linux/i2c-omap.h> +#include <linux/platform_data/i2c-omap.h> #include <linux/reboot.h> #include <linux/irqchip/irq-omap-intc.h> @@ -44,6 +44,9 @@ #define OMAP_INTC_START NR_IRQS +extern int (*omap_pm_soc_init)(void); +int omap_pm_nop_init(void); + #if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP2) int omap2_pm_init(void); #else @@ -79,9 +82,12 @@ static inline int omap4_pm_init_early(void) #if defined(CONFIG_PM) && (defined(CONFIG_SOC_AM33XX) || \ defined(CONFIG_SOC_AM43XX)) -void amx3_common_pm_init(void); +int amx3_common_pm_init(void); #else -static inline void amx3_common_pm_init(void) { } +static inline int amx3_common_pm_init(void) +{ + return 0; +} #endif extern void omap2_init_common_infrastructure(void); @@ -122,14 +128,10 @@ void am43xx_init_early(void); void am43xx_init_late(void); void omap4430_init_early(void); void omap5_init_early(void); -void omap3_init_late(void); /* Do not use this one */ +void omap3_init_late(void); void omap4430_init_late(void); void omap2420_init_late(void); void omap2430_init_late(void); -void omap3430_init_late(void); -void omap35xx_init_late(void); -void omap3630_init_late(void); -void am35xx_init_late(void); void ti81xx_init_late(void); void am33xx_init_late(void); void omap5_init_late(void); @@ -350,7 +352,5 @@ extern int omap_dss_reset(struct omap_hwmod *); /* SoC specific clock initializer */ int omap_clk_init(void); -int __init omapdss_init_of(void); - #endif /* __ASSEMBLER__ */ #endif /* __ARCH_ARM_MACH_OMAP2PLUS_COMMON_H */ diff --git a/arch/arm/mach-omap2/control.c b/arch/arm/mach-omap2/control.c index 180da403639e..0bbfb20e193f 100644 --- a/arch/arm/mach-omap2/control.c +++ b/arch/arm/mach-omap2/control.c @@ -17,6 +17,7 @@ #include <linux/of_address.h> #include <linux/regmap.h> #include <linux/mfd/syscon.h> +#include <linux/cpu_pm.h> #include "soc.h" #include "iomap.h" @@ -621,6 +622,110 @@ void __init omap3_ctrl_init(void) } #endif /* CONFIG_ARCH_OMAP3 && CONFIG_PM */ +static unsigned long am43xx_control_reg_offsets[] = { + AM33XX_CONTROL_SYSCONFIG_OFFSET, + AM33XX_CONTROL_STATUS_OFFSET, + AM43XX_CONTROL_MPU_L2_CTRL_OFFSET, + AM33XX_CONTROL_CORE_SLDO_CTRL_OFFSET, + AM33XX_CONTROL_MPU_SLDO_CTRL_OFFSET, + AM33XX_CONTROL_CLK32KDIVRATIO_CTRL_OFFSET, + AM33XX_CONTROL_BANDGAP_CTRL_OFFSET, + AM33XX_CONTROL_BANDGAP_TRIM_OFFSET, + AM33XX_CONTROL_PLL_CLKINPULOW_CTRL_OFFSET, + AM33XX_CONTROL_MOSC_CTRL_OFFSET, + AM33XX_CONTROL_DEEPSLEEP_CTRL_OFFSET, + AM43XX_CONTROL_DISPLAY_PLL_SEL_OFFSET, + AM33XX_CONTROL_INIT_PRIORITY_0_OFFSET, + AM33XX_CONTROL_INIT_PRIORITY_1_OFFSET, + AM33XX_CONTROL_TPTC_CFG_OFFSET, + AM33XX_CONTROL_USB_CTRL0_OFFSET, + AM33XX_CONTROL_USB_CTRL1_OFFSET, + AM43XX_CONTROL_USB_CTRL2_OFFSET, + AM43XX_CONTROL_GMII_SEL_OFFSET, + AM43XX_CONTROL_MPUSS_CTRL_OFFSET, + AM43XX_CONTROL_TIMER_CASCADE_CTRL_OFFSET, + AM43XX_CONTROL_PWMSS_CTRL_OFFSET, + AM33XX_CONTROL_MREQPRIO_0_OFFSET, + AM33XX_CONTROL_MREQPRIO_1_OFFSET, + AM33XX_CONTROL_HW_EVENT_SEL_GRP1_OFFSET, + AM33XX_CONTROL_HW_EVENT_SEL_GRP2_OFFSET, + AM33XX_CONTROL_HW_EVENT_SEL_GRP3_OFFSET, + AM33XX_CONTROL_HW_EVENT_SEL_GRP4_OFFSET, + AM33XX_CONTROL_SMRT_CTRL_OFFSET, + AM33XX_CONTROL_MPUSS_HW_DEBUG_SEL_OFFSET, + AM43XX_CONTROL_CQDETECT_STS_OFFSET, + AM43XX_CONTROL_CQDETECT_STS2_OFFSET, + AM43XX_CONTROL_VTP_CTRL_OFFSET, + AM33XX_CONTROL_VREF_CTRL_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_0_3_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_4_7_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_8_11_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_12_15_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_16_19_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_20_23_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_24_27_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_28_31_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_32_35_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_36_39_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_40_43_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_44_47_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_48_51_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_52_55_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_56_59_OFFSET, + AM33XX_CONTROL_TPCC_EVT_MUX_60_63_OFFSET, + AM33XX_CONTROL_TIMER_EVT_CAPT_OFFSET, + AM33XX_CONTROL_ECAP_EVT_CAPT_OFFSET, + AM33XX_CONTROL_ADC_EVT_CAPT_OFFSET, + AM43XX_CONTROL_ADC1_EVT_CAPT_OFFSET, + AM33XX_CONTROL_RESET_ISO_OFFSET, +}; + +static u32 am33xx_control_vals[ARRAY_SIZE(am43xx_control_reg_offsets)]; + +/** + * am43xx_control_save_context - Save the wakeup domain registers + * + * Save the wkup domain registers + */ +void am43xx_control_save_context(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(am43xx_control_reg_offsets); i++) + am33xx_control_vals[i] = + omap_ctrl_readl(am43xx_control_reg_offsets[i]); +} + +/** + * am43xx_control_restore_context - Restore the wakeup domain registers + * + * Restore the wkup domain registers + */ +void am43xx_control_restore_context(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(am43xx_control_reg_offsets); i++) + omap_ctrl_writel(am33xx_control_vals[i], + am43xx_control_reg_offsets[i]); +} + +static int cpu_notifier(struct notifier_block *nb, unsigned long cmd, void *v) +{ + switch (cmd) { + case CPU_CLUSTER_PM_ENTER: + if (enable_off_mode) + am43xx_control_save_context(); + break; + case CPU_CLUSTER_PM_EXIT: + if (enable_off_mode) + am43xx_control_restore_context(); + break; + } + + return NOTIFY_OK; +} + struct control_init_data { int index; void __iomem *mem; @@ -699,6 +804,7 @@ int __init omap_control_init(void) const struct omap_prcm_init_data *data; int ret; struct regmap *syscon; + static struct notifier_block nb; for_each_matching_node_and_match(np, omap_scrm_dt_match_table, &match) { data = match->data; @@ -731,6 +837,12 @@ int __init omap_control_init(void) } } + /* Only AM43XX can lose ctrl registers context during rtc-ddr suspend */ + if (soc_is_am43xx()) { + nb.notifier_call = cpu_notifier; + cpu_pm_register_notifier(&nb); + } + return 0; } diff --git a/arch/arm/mach-omap2/control.h b/arch/arm/mach-omap2/control.h index ec406bc2c6d4..393b42110511 100644 --- a/arch/arm/mach-omap2/control.h +++ b/arch/arm/mach-omap2/control.h @@ -409,6 +409,67 @@ #define AM33XX_DEV_FEATURE 0x604 #define AM33XX_SGX_MASK BIT(29) +/* Additional AM33XX/AM43XX CONTROL registers */ +#define AM33XX_CONTROL_SYSCONFIG_OFFSET 0x0010 +#define AM33XX_CONTROL_STATUS_OFFSET 0x0040 +#define AM43XX_CONTROL_MPU_L2_CTRL_OFFSET 0x01e0 +#define AM33XX_CONTROL_CORTEX_VBBLDO_CTRL_OFFSET 0x041c +#define AM33XX_CONTROL_CORE_SLDO_CTRL_OFFSET 0x0428 +#define AM33XX_CONTROL_MPU_SLDO_CTRL_OFFSET 0x042c +#define AM33XX_CONTROL_CLK32KDIVRATIO_CTRL_OFFSET 0x0444 +#define AM33XX_CONTROL_BANDGAP_CTRL_OFFSET 0x0448 +#define AM33XX_CONTROL_BANDGAP_TRIM_OFFSET 0x044c +#define AM33XX_CONTROL_PLL_CLKINPULOW_CTRL_OFFSET 0x0458 +#define AM33XX_CONTROL_MOSC_CTRL_OFFSET 0x0468 +#define AM33XX_CONTROL_RCOSC_CTRL_OFFSET 0x046c +#define AM33XX_CONTROL_DEEPSLEEP_CTRL_OFFSET 0x0470 +#define AM43XX_CONTROL_DISPLAY_PLL_SEL_OFFSET 0x0534 +#define AM33XX_CONTROL_INIT_PRIORITY_0_OFFSET 0x0608 +#define AM33XX_CONTROL_INIT_PRIORITY_1_OFFSET 0x060c +#define AM33XX_CONTROL_MMU_CFG_OFFSET 0x0610 +#define AM33XX_CONTROL_TPTC_CFG_OFFSET 0x0614 +#define AM33XX_CONTROL_USB_CTRL0_OFFSET 0x0620 +#define AM33XX_CONTROL_USB_CTRL1_OFFSET 0x0628 +#define AM33XX_CONTROL_USB_WKUP_CTRL_OFFSET 0x0648 +#define AM43XX_CONTROL_USB_CTRL2_OFFSET 0x064c +#define AM43XX_CONTROL_GMII_SEL_OFFSET 0x0650 +#define AM43XX_CONTROL_MPUSS_CTRL_OFFSET 0x0654 +#define AM43XX_CONTROL_TIMER_CASCADE_CTRL_OFFSET 0x0658 +#define AM43XX_CONTROL_PWMSS_CTRL_OFFSET 0x0664 +#define AM33XX_CONTROL_MREQPRIO_0_OFFSET 0x0670 +#define AM33XX_CONTROL_MREQPRIO_1_OFFSET 0x0674 +#define AM33XX_CONTROL_HW_EVENT_SEL_GRP1_OFFSET 0x0690 +#define AM33XX_CONTROL_HW_EVENT_SEL_GRP2_OFFSET 0x0694 +#define AM33XX_CONTROL_HW_EVENT_SEL_GRP3_OFFSET 0x0698 +#define AM33XX_CONTROL_HW_EVENT_SEL_GRP4_OFFSET 0x069c +#define AM33XX_CONTROL_SMRT_CTRL_OFFSET 0x06a0 +#define AM33XX_CONTROL_MPUSS_HW_DEBUG_SEL_OFFSET 0x06a4 +#define AM43XX_CONTROL_CQDETECT_STS_OFFSET 0x0e00 +#define AM43XX_CONTROL_CQDETECT_STS2_OFFSET 0x0e08 +#define AM43XX_CONTROL_VTP_CTRL_OFFSET 0x0e0c +#define AM33XX_CONTROL_VREF_CTRL_OFFSET 0x0e14 +#define AM33XX_CONTROL_TPCC_EVT_MUX_0_3_OFFSET 0x0f90 +#define AM33XX_CONTROL_TPCC_EVT_MUX_4_7_OFFSET 0x0f94 +#define AM33XX_CONTROL_TPCC_EVT_MUX_8_11_OFFSET 0x0f98 +#define AM33XX_CONTROL_TPCC_EVT_MUX_12_15_OFFSET 0x0f9c +#define AM33XX_CONTROL_TPCC_EVT_MUX_16_19_OFFSET 0x0fa0 +#define AM33XX_CONTROL_TPCC_EVT_MUX_20_23_OFFSET 0x0fa4 +#define AM33XX_CONTROL_TPCC_EVT_MUX_24_27_OFFSET 0x0fa8 +#define AM33XX_CONTROL_TPCC_EVT_MUX_28_31_OFFSET 0x0fac +#define AM33XX_CONTROL_TPCC_EVT_MUX_32_35_OFFSET 0x0fb0 +#define AM33XX_CONTROL_TPCC_EVT_MUX_36_39_OFFSET 0x0fb4 +#define AM33XX_CONTROL_TPCC_EVT_MUX_40_43_OFFSET 0x0fb8 +#define AM33XX_CONTROL_TPCC_EVT_MUX_44_47_OFFSET 0x0fbc +#define AM33XX_CONTROL_TPCC_EVT_MUX_48_51_OFFSET 0x0fc0 +#define AM33XX_CONTROL_TPCC_EVT_MUX_52_55_OFFSET 0x0fc4 +#define AM33XX_CONTROL_TPCC_EVT_MUX_56_59_OFFSET 0x0fc8 +#define AM33XX_CONTROL_TPCC_EVT_MUX_60_63_OFFSET 0x0fcc +#define AM33XX_CONTROL_TIMER_EVT_CAPT_OFFSET 0x0fd0 +#define AM33XX_CONTROL_ECAP_EVT_CAPT_OFFSET 0x0fd4 +#define AM33XX_CONTROL_ADC_EVT_CAPT_OFFSET 0x0fd8 +#define AM43XX_CONTROL_ADC1_EVT_CAPT_OFFSET 0x0fdc +#define AM33XX_CONTROL_RESET_ISO_OFFSET 0x1000 + /* CONTROL OMAP STATUS register to identify OMAP3 features */ #define OMAP3_CONTROL_OMAP_STATUS 0x044c diff --git a/arch/arm/mach-omap2/display.c b/arch/arm/mach-omap2/display.c index b3f6eb5d04a2..9500b6e27380 100644 --- a/arch/arm/mach-omap2/display.c +++ b/arch/arm/mach-omap2/display.c @@ -32,7 +32,6 @@ #include <linux/platform_data/omapdss.h> #include "omap_hwmod.h" #include "omap_device.h" -#include "omap-pm.h" #include "common.h" #include "soc.h" @@ -126,11 +125,6 @@ static void omap_dsi_disable_pads(int dsi_id, unsigned lane_mask) omap4_dsi_mux_pads(dsi_id, 0); } -static int omap_dss_set_min_bus_tput(struct device *dev, unsigned long tput) -{ - return omap_pm_set_min_bus_tput(dev, OCP_INITIATOR_AGENT, tput); -} - static enum omapdss_version __init omap_display_get_version(void) { if (cpu_is_omap24xx()) @@ -169,7 +163,6 @@ static int __init omapdss_init_fbdev(void) static struct omap_dss_board_info board_data = { .dsi_enable_pads = omap_dsi_enable_pads, .dsi_disable_pads = omap_dsi_disable_pads, - .set_min_bus_tput = omap_dss_set_min_bus_tput, }; struct device_node *node; int r; @@ -392,7 +385,7 @@ static struct device_node * __init omapdss_find_dss_of_node(void) return NULL; } -int __init omapdss_init_of(void) +static int __init omapdss_init_of(void) { int r; struct device_node *node; @@ -422,3 +415,4 @@ int __init omapdss_init_of(void) return omapdss_init_fbdev(); } +omap_device_initcall(omapdss_init_of); diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c index b064066d431c..af545193f673 100644 --- a/arch/arm/mach-omap2/hsmmc.c +++ b/arch/arm/mach-omap2/hsmmc.c @@ -18,7 +18,6 @@ #include "soc.h" #include "omap_device.h" -#include "omap-pm.h" #include "hsmmc.h" #include "control.h" @@ -35,7 +34,7 @@ static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c, { char *hc_name; - hc_name = kzalloc(sizeof(char) * (HSMMC_NAME_LEN + 1), GFP_KERNEL); + hc_name = kzalloc(HSMMC_NAME_LEN + 1, GFP_KERNEL); if (!hc_name) { kfree(hc_name); return -ENOMEM; diff --git a/arch/arm/mach-omap2/i2c.c b/arch/arm/mach-omap2/i2c.c index 91a21c3923b2..37ff25ee3d89 100644 --- a/arch/arm/mach-omap2/i2c.c +++ b/arch/arm/mach-omap2/i2c.c @@ -22,7 +22,6 @@ #include "soc.h" #include "omap_hwmod.h" #include "omap_device.h" -#include "omap-pm.h" #include "prm.h" #include "common.h" diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index cf546dfe3b32..bb8e0bb7ef5d 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -37,7 +37,6 @@ #include "clock.h" #include "clock2xxx.h" #include "clock3xxx.h" -#include "omap-pm.h" #include "sdrc.h" #include "control.h" #include "serial.h" @@ -421,13 +420,6 @@ static void __init __maybe_unused omap_hwmod_init_postsetup(void) postsetup_state = _HWMOD_STATE_ENABLED; #endif omap_hwmod_for_each(_set_hwmod_postsetup_state, &postsetup_state); - - omap_pm_if_early_init(); -} - -static void __init __maybe_unused omap_common_late_init(void) -{ - omap2_common_pm_late_init(); } #ifdef CONFIG_SOC_OMAP2420 @@ -450,9 +442,7 @@ void __init omap2420_init_early(void) void __init omap2420_init_late(void) { - omap_common_late_init(); - omap2_pm_init(); - omap2_clk_enable_autoidle_all(); + omap_pm_soc_init = omap2_pm_init; } #endif @@ -476,9 +466,7 @@ void __init omap2430_init_early(void) void __init omap2430_init_late(void) { - omap_common_late_init(); - omap2_pm_init(); - omap2_clk_enable_autoidle_all(); + omap_pm_soc_init = omap2_pm_init; } #endif @@ -529,43 +517,12 @@ void __init am35xx_init_early(void) void __init omap3_init_late(void) { - omap_common_late_init(); - omap3_pm_init(); - omap2_clk_enable_autoidle_all(); -} - -void __init omap3430_init_late(void) -{ - omap_common_late_init(); - omap3_pm_init(); - omap2_clk_enable_autoidle_all(); -} - -void __init omap35xx_init_late(void) -{ - omap_common_late_init(); - omap3_pm_init(); - omap2_clk_enable_autoidle_all(); -} - -void __init omap3630_init_late(void) -{ - omap_common_late_init(); - omap3_pm_init(); - omap2_clk_enable_autoidle_all(); -} - -void __init am35xx_init_late(void) -{ - omap_common_late_init(); - omap3_pm_init(); - omap2_clk_enable_autoidle_all(); + omap_pm_soc_init = omap3_pm_init; } void __init ti81xx_init_late(void) { - omap_common_late_init(); - omap2_clk_enable_autoidle_all(); + omap_pm_soc_init = omap_pm_nop_init; } #endif @@ -621,8 +578,7 @@ void __init am33xx_init_early(void) void __init am33xx_init_late(void) { - omap_common_late_init(); - amx3_common_pm_init(); + omap_pm_soc_init = amx3_common_pm_init; } #endif @@ -645,9 +601,7 @@ void __init am43xx_init_early(void) void __init am43xx_init_late(void) { - omap_common_late_init(); - omap2_clk_enable_autoidle_all(); - amx3_common_pm_init(); + omap_pm_soc_init = amx3_common_pm_init; } #endif @@ -675,9 +629,7 @@ void __init omap4430_init_early(void) void __init omap4430_init_late(void) { - omap_common_late_init(); - omap4_pm_init(); - omap2_clk_enable_autoidle_all(); + omap_pm_soc_init = omap4_pm_init; } #endif @@ -703,9 +655,7 @@ void __init omap5_init_early(void) void __init omap5_init_late(void) { - omap_common_late_init(); - omap4_pm_init(); - omap2_clk_enable_autoidle_all(); + omap_pm_soc_init = omap4_pm_init; } #endif @@ -728,9 +678,7 @@ void __init dra7xx_init_early(void) void __init dra7xx_init_late(void) { - omap_common_late_init(); - omap4_pm_init(); - omap2_clk_enable_autoidle_all(); + omap_pm_soc_init = omap4_pm_init; } #endif diff --git a/arch/arm/mach-omap2/omap-pm-noop.c b/arch/arm/mach-omap2/omap-pm-noop.c deleted file mode 100644 index 4ead077ea4e7..000000000000 --- a/arch/arm/mach-omap2/omap-pm-noop.c +++ /dev/null @@ -1,176 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * omap-pm-noop.c - OMAP power management interface - dummy version - * - * This code implements the OMAP power management interface to - * drivers, CPUIdle, CPUFreq, and DSP Bridge. It is strictly for - * debug/demonstration use, as it does nothing but printk() whenever a - * function is called (when DEBUG is defined, below) - * - * Copyright (C) 2008-2009 Texas Instruments, Inc. - * Copyright (C) 2008-2009 Nokia Corporation - * Paul Walmsley - * - * Interface developed by (in alphabetical order): - * Karthik Dasu, Tony Lindgren, Rajendra Nayak, Sakari Poussa, Veeramanikandan - * Raju, Anand Sawant, Igor Stoppa, Paul Walmsley, Richard Woodruff - */ - -#undef DEBUG - -#include <linux/init.h> -#include <linux/cpufreq.h> -#include <linux/device.h> -#include <linux/platform_device.h> - -#include "omap_device.h" -#include "omap-pm.h" - -static bool off_mode_enabled; -static int dummy_context_loss_counter; - -/* - * Device-driver-originated constraints (via board-*.c files) - */ - -int omap_pm_set_max_mpu_wakeup_lat(struct device *dev, long t) -{ - if (!dev || t < -1) { - WARN(1, "OMAP PM: %s: invalid parameter(s)", __func__); - return -EINVAL; - } - - if (t == -1) - pr_debug("OMAP PM: remove max MPU wakeup latency constraint: dev %s\n", - dev_name(dev)); - else - pr_debug("OMAP PM: add max MPU wakeup latency constraint: dev %s, t = %ld usec\n", - dev_name(dev), t); - - /* - * For current Linux, this needs to map the MPU to a - * powerdomain, then go through the list of current max lat - * constraints on the MPU and find the smallest. If - * the latency constraint has changed, the code should - * recompute the state to enter for the next powerdomain - * state. - * - * TI CDP code can call constraint_set here. - */ - - return 0; -} - -int omap_pm_set_min_bus_tput(struct device *dev, u8 agent_id, unsigned long r) -{ - if (!dev || (agent_id != OCP_INITIATOR_AGENT && - agent_id != OCP_TARGET_AGENT)) { - WARN(1, "OMAP PM: %s: invalid parameter(s)", __func__); - return -EINVAL; - } - - if (r == 0) - pr_debug("OMAP PM: remove min bus tput constraint: dev %s for agent_id %d\n", - dev_name(dev), agent_id); - else - pr_debug("OMAP PM: add min bus tput constraint: dev %s for agent_id %d: rate %ld KiB\n", - dev_name(dev), agent_id, r); - - /* - * This code should model the interconnect and compute the - * required clock frequency, convert that to a VDD2 OPP ID, then - * set the VDD2 OPP appropriately. - * - * TI CDP code can call constraint_set here on the VDD2 OPP. - */ - - return 0; -} - -/* - * DSP Bridge-specific constraints - */ - - -/** - * omap_pm_enable_off_mode - notify OMAP PM that off-mode is enabled - * - * Intended for use only by OMAP PM core code to notify this layer - * that off mode has been enabled. - */ -void omap_pm_enable_off_mode(void) -{ - off_mode_enabled = true; -} - -/** - * omap_pm_disable_off_mode - notify OMAP PM that off-mode is disabled - * - * Intended for use only by OMAP PM core code to notify this layer - * that off mode has been disabled. - */ -void omap_pm_disable_off_mode(void) -{ - off_mode_enabled = false; -} - -/* - * Device context loss tracking - */ - -#ifdef CONFIG_ARCH_OMAP2PLUS - -int omap_pm_get_dev_context_loss_count(struct device *dev) -{ - struct platform_device *pdev = to_platform_device(dev); - int count; - - if (WARN_ON(!dev)) - return -ENODEV; - - if (dev->pm_domain == &omap_device_pm_domain) { - count = omap_device_get_context_loss_count(pdev); - } else { - WARN_ONCE(off_mode_enabled, "omap_pm: using dummy context loss counter; device %s should be converted to omap_device", - dev_name(dev)); - - count = dummy_context_loss_counter; - - if (off_mode_enabled) { - count++; - /* - * Context loss count has to be a non-negative value. - * Clear the sign bit to get a value range from 0 to - * INT_MAX. - */ - count &= INT_MAX; - dummy_context_loss_counter = count; - } - } - - pr_debug("OMAP PM: context loss count for dev %s = %d\n", - dev_name(dev), count); - - return count; -} - -#else - -int omap_pm_get_dev_context_loss_count(struct device *dev) -{ - return dummy_context_loss_counter; -} - -#endif - -/* Should be called before clk framework init */ -int __init omap_pm_if_early_init(void) -{ - return 0; -} - -/* Must be called after clock framework is initialized */ -int __init omap_pm_if_init(void) -{ - return 0; -} diff --git a/arch/arm/mach-omap2/omap-pm.h b/arch/arm/mach-omap2/omap-pm.h deleted file mode 100644 index 5ba5df47f91b..000000000000 --- a/arch/arm/mach-omap2/omap-pm.h +++ /dev/null @@ -1,161 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* - * omap-pm.h - OMAP power management interface - * - * Copyright (C) 2008-2010 Texas Instruments, Inc. - * Copyright (C) 2008-2010 Nokia Corporation - * Paul Walmsley - * - * Interface developed by (in alphabetical order): Karthik Dasu, Jouni - * Högander, Tony Lindgren, Rajendra Nayak, Sakari Poussa, - * Veeramanikandan Raju, Anand Sawant, Igor Stoppa, Paul Walmsley, - * Richard Woodruff - */ - -#ifndef ASM_ARM_ARCH_OMAP_OMAP_PM_H -#define ASM_ARM_ARCH_OMAP_OMAP_PM_H - -#include <linux/device.h> -#include <linux/cpufreq.h> -#include <linux/clk.h> -#include <linux/pm_opp.h> - -/* - * agent_id values for use with omap_pm_set_min_bus_tput(): - * - * OCP_INITIATOR_AGENT is only valid for devices that can act as - * initiators -- it represents the device's L3 interconnect - * connection. OCP_TARGET_AGENT represents the device's L4 - * interconnect connection. - */ -#define OCP_TARGET_AGENT 1 -#define OCP_INITIATOR_AGENT 2 - -/** - * omap_pm_if_early_init - OMAP PM init code called before clock fw init - * @mpu_opp_table: array ptr to struct omap_opp for MPU - * @dsp_opp_table: array ptr to struct omap_opp for DSP - * @l3_opp_table : array ptr to struct omap_opp for CORE - * - * Initialize anything that must be configured before the clock - * framework starts. The "_if_" is to avoid name collisions with the - * PM idle-loop code. - */ -int __init omap_pm_if_early_init(void); - -/** - * omap_pm_if_init - OMAP PM init code called after clock fw init - * - * The main initialization code. OPP tables are passed in here. The - * "_if_" is to avoid name collisions with the PM idle-loop code. - */ -int __init omap_pm_if_init(void); - -/* - * Device-driver-originated constraints (via board-*.c files, platform_data) - */ - - -/** - * omap_pm_set_max_mpu_wakeup_lat - set the maximum MPU wakeup latency - * @dev: struct device * requesting the constraint - * @t: maximum MPU wakeup latency in microseconds - * - * Request that the maximum interrupt latency for the MPU to be no - * greater than @t microseconds. "Interrupt latency" in this case is - * defined as the elapsed time from the occurrence of a hardware or - * timer interrupt to the time when the device driver's interrupt - * service routine has been entered by the MPU. - * - * It is intended that underlying PM code will use this information to - * determine what power state to put the MPU powerdomain into, and - * possibly the CORE powerdomain as well, since interrupt handling - * code currently runs from SDRAM. Advanced PM or board*.c code may - * also configure interrupt controller priorities, OCP bus priorities, - * CPU speed(s), etc. - * - * This function will not affect device wakeup latency, e.g., time - * elapsed from when a device driver enables a hardware device with - * clk_enable(), to when the device is ready for register access or - * other use. To control this device wakeup latency, use - * omap_pm_set_max_dev_wakeup_lat() - * - * Multiple calls to omap_pm_set_max_mpu_wakeup_lat() will replace the - * previous t value. To remove the latency target for the MPU, call - * with t = -1. - * - * XXX This constraint will be deprecated soon in favor of the more - * general omap_pm_set_max_dev_wakeup_lat() - * - * Returns -EINVAL for an invalid argument, -ERANGE if the constraint - * is not satisfiable, or 0 upon success. - */ -int omap_pm_set_max_mpu_wakeup_lat(struct device *dev, long t); - - -/** - * omap_pm_set_min_bus_tput - set minimum bus throughput needed by device - * @dev: struct device * requesting the constraint - * @tbus_id: interconnect to operate on (OCP_{INITIATOR,TARGET}_AGENT) - * @r: minimum throughput (in KiB/s) - * - * Request that the minimum data throughput on the OCP interconnect - * attached to device @dev interconnect agent @tbus_id be no less - * than @r KiB/s. - * - * It is expected that the OMAP PM or bus code will use this - * information to set the interconnect clock to run at the lowest - * possible speed that satisfies all current system users. The PM or - * bus code will adjust the estimate based on its model of the bus, so - * device driver authors should attempt to specify an accurate - * quantity for their device use case, and let the PM or bus code - * overestimate the numbers as necessary to handle request/response - * latency, other competing users on the system, etc. On OMAP2/3, if - * a driver requests a minimum L4 interconnect speed constraint, the - * code will also need to add an minimum L3 interconnect speed - * constraint, - * - * Multiple calls to omap_pm_set_min_bus_tput() will replace the - * previous rate value for this device. To remove the interconnect - * throughput restriction for this device, call with r = 0. - * - * Returns -EINVAL for an invalid argument, -ERANGE if the constraint - * is not satisfiable, or 0 upon success. - */ -int omap_pm_set_min_bus_tput(struct device *dev, u8 agent_id, unsigned long r); - - -/* - * CPUFreq-originated constraint - * - * In the future, this should be handled by custom OPP clocktype - * functions. - */ - - -/* - * Device context loss tracking - */ - -/** - * omap_pm_get_dev_context_loss_count - return count of times dev has lost ctx - * @dev: struct device * - * - * This function returns the number of times that the device @dev has - * lost its internal context. This generally occurs on a powerdomain - * transition to OFF. Drivers use this as an optimization to avoid restoring - * context if the device hasn't lost it. To use, drivers should initially - * call this in their context save functions and store the result. Early in - * the driver's context restore function, the driver should call this function - * again, and compare the result to the stored counter. If they differ, the - * driver must restore device context. If the number of context losses - * exceeds the maximum positive integer, the function will wrap to 0 and - * continue counting. Returns the number of context losses for this device, - * or negative value upon error. - */ -int omap_pm_get_dev_context_loss_count(struct device *dev); - -void omap_pm_enable_off_mode(void); -void omap_pm_disable_off_mode(void); - -#endif diff --git a/arch/arm/mach-omap2/omap_device.c b/arch/arm/mach-omap2/omap_device.c index 3b829a50d1db..41c7b905980a 100644 --- a/arch/arm/mach-omap2/omap_device.c +++ b/arch/arm/mach-omap2/omap_device.c @@ -143,7 +143,7 @@ static int omap_device_build_from_dt(struct platform_device *pdev) struct resource res; const char *oh_name; int oh_cnt, i, ret = 0; - bool device_active = false; + bool device_active = false, skip_pm_domain = false; oh_cnt = of_property_count_strings(node, "ti,hwmods"); if (oh_cnt <= 0) { @@ -151,11 +151,18 @@ static int omap_device_build_from_dt(struct platform_device *pdev) return -ENODEV; } + /* SDMA still needs special handling for omap_device_build() */ + ret = of_property_read_string_index(node, "ti,hwmods", 0, &oh_name); + if (!ret && (!strncmp("dma_system", oh_name, 10) || + !strncmp("dma", oh_name, 3))) + skip_pm_domain = true; + /* Use ti-sysc driver instead of omap_device? */ - if (!omap_hwmod_parse_module_range(NULL, node, &res)) + if (!skip_pm_domain && + !omap_hwmod_parse_module_range(NULL, node, &res)) return -ENODEV; - hwmods = kzalloc(sizeof(struct omap_hwmod *) * oh_cnt, GFP_KERNEL); + hwmods = kcalloc(oh_cnt, sizeof(struct omap_hwmod *), GFP_KERNEL); if (!hwmods) { ret = -ENOMEM; goto odbfd_exit; @@ -191,11 +198,12 @@ static int omap_device_build_from_dt(struct platform_device *pdev) r->name = dev_name(&pdev->dev); } - dev_pm_domain_set(&pdev->dev, &omap_device_pm_domain); - - if (device_active) { - omap_device_enable(pdev); - pm_runtime_set_active(&pdev->dev); + if (!skip_pm_domain) { + dev_pm_domain_set(&pdev->dev, &omap_device_pm_domain); + if (device_active) { + omap_device_enable(pdev); + pm_runtime_set_active(&pdev->dev); + } } odbfd_exit1: @@ -405,7 +413,7 @@ omap_device_copy_resources(struct omap_hwmod *oh, goto error; } - res = kzalloc(sizeof(*res) * 2, GFP_KERNEL); + res = kcalloc(2, sizeof(*res), GFP_KERNEL); if (!res) return -ENOMEM; diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c index e7d23e200ecc..2ceffd85dd3d 100644 --- a/arch/arm/mach-omap2/omap_hwmod.c +++ b/arch/arm/mach-omap2/omap_hwmod.c @@ -481,7 +481,7 @@ static int _wait_softreset_complete(struct omap_hwmod *oh) sysc = oh->class->sysc; - if (sysc->sysc_flags & SYSS_HAS_RESET_STATUS) + if (sysc->sysc_flags & SYSS_HAS_RESET_STATUS && sysc->syss_offs > 0) omap_test_timeout((omap_hwmod_read(oh, sysc->syss_offs) & SYSS_RESETDONE_MASK), MAX_MODULE_SOFTRESET_WAIT, c); @@ -3171,19 +3171,19 @@ static int omap_hwmod_init_regbits(struct device *dev, */ int omap_hwmod_init_reg_offs(struct device *dev, const struct ti_sysc_module_data *data, - u32 *rev_offs, u32 *sysc_offs, u32 *syss_offs) + s32 *rev_offs, s32 *sysc_offs, s32 *syss_offs) { - *rev_offs = 0; + *rev_offs = -ENODEV; *sysc_offs = 0; *syss_offs = 0; - if (data->offsets[SYSC_REVISION] > 0) + if (data->offsets[SYSC_REVISION] >= 0) *rev_offs = data->offsets[SYSC_REVISION]; - if (data->offsets[SYSC_SYSCONFIG] > 0) + if (data->offsets[SYSC_SYSCONFIG] >= 0) *sysc_offs = data->offsets[SYSC_SYSCONFIG]; - if (data->offsets[SYSC_SYSSTATUS] > 0) + if (data->offsets[SYSC_SYSSTATUS] >= 0) *syss_offs = data->offsets[SYSC_SYSSTATUS]; return 0; @@ -3312,8 +3312,8 @@ static int omap_hwmod_check_module(struct device *dev, struct omap_hwmod *oh, const struct ti_sysc_module_data *data, struct sysc_regbits *sysc_fields, - u32 rev_offs, u32 sysc_offs, - u32 syss_offs, u32 sysc_flags, + s32 rev_offs, s32 sysc_offs, + s32 syss_offs, u32 sysc_flags, u32 idlemodes) { if (!oh->class->sysc) @@ -3365,7 +3365,7 @@ static int omap_hwmod_check_module(struct device *dev, int omap_hwmod_allocate_module(struct device *dev, struct omap_hwmod *oh, const struct ti_sysc_module_data *data, struct sysc_regbits *sysc_fields, - u32 rev_offs, u32 sysc_offs, u32 syss_offs, + s32 rev_offs, s32 sysc_offs, s32 syss_offs, u32 sysc_flags, u32 idlemodes) { struct omap_hwmod_class_sysconfig *sysc; @@ -3425,7 +3425,8 @@ int omap_hwmod_init_module(struct device *dev, { struct omap_hwmod *oh; struct sysc_regbits *sysc_fields; - u32 rev_offs, sysc_offs, syss_offs, sysc_flags, idlemodes; + s32 rev_offs, sysc_offs, syss_offs; + u32 sysc_flags, idlemodes; int error; if (!dev || !data) diff --git a/arch/arm/mach-omap2/omap_hwmod.h b/arch/arm/mach-omap2/omap_hwmod.h index c7122abbf977..b70cdc21f8a2 100644 --- a/arch/arm/mach-omap2/omap_hwmod.h +++ b/arch/arm/mach-omap2/omap_hwmod.h @@ -317,9 +317,9 @@ struct omap_hwmod_ocp_if { * then this field has to be populated with the correct offset structure. */ struct omap_hwmod_class_sysconfig { - u32 rev_offs; - u32 sysc_offs; - u32 syss_offs; + s32 rev_offs; + s32 sysc_offs; + s32 syss_offs; u16 sysc_flags; struct sysc_regbits *sysc_fields; u8 srst_udelay; diff --git a/arch/arm/mach-omap2/omap_hwmod_2420_data.c b/arch/arm/mach-omap2/omap_hwmod_2420_data.c index fe66cf247874..d684fac8f592 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2420_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2420_data.c @@ -13,7 +13,7 @@ * XXX these should be marked initdata for multi-OMAP kernels */ -#include <linux/i2c-omap.h> +#include <linux/platform_data/i2c-omap.h> #include <linux/omap-dma.h> #include "omap_hwmod.h" diff --git a/arch/arm/mach-omap2/omap_hwmod_2430_data.c b/arch/arm/mach-omap2/omap_hwmod_2430_data.c index 74eefd30518c..abef9f6f9bf5 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2430_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2430_data.c @@ -13,7 +13,7 @@ * XXX these should be marked initdata for multi-OMAP kernels */ -#include <linux/i2c-omap.h> +#include <linux/platform_data/i2c-omap.h> #include <linux/platform_data/hsmmc-omap.h> #include <linux/omap-dma.h> diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c index 5efe91c6e95b..9ded7bf972e7 100644 --- a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c @@ -629,6 +629,7 @@ struct omap_hwmod am33xx_gpmc_hwmod = { /* 'i2c' class */ static struct omap_hwmod_class_sysconfig am33xx_i2c_sysc = { + .rev_offs = 0, .sysc_offs = 0x0010, .syss_offs = 0x0090, .sysc_flags = (SYSC_HAS_AUTOIDLE | SYSC_HAS_CLOCKACTIVITY | diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_data.c index 53e1ac3724f2..c9483bc06228 100644 --- a/arch/arm/mach-omap2/omap_hwmod_33xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_33xx_data.c @@ -14,7 +14,7 @@ * GNU General Public License for more details. */ -#include <linux/i2c-omap.h> +#include <linux/platform_data/i2c-omap.h> #include "omap_hwmod.h" #include "omap_hwmod_common_data.h" diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c index 23336b6c7125..23e6a41a18eb 100644 --- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c @@ -15,7 +15,7 @@ * XXX these should be marked initdata for multi-OMAP kernels */ -#include <linux/i2c-omap.h> +#include <linux/platform_data/i2c-omap.h> #include <linux/power/smartreflex.h> #include <linux/platform_data/hsmmc-omap.h> @@ -885,6 +885,7 @@ static struct omap_hwmod omap3xxx_dma_system_hwmod = { */ static struct omap_hwmod_class_sysconfig omap3xxx_mcbsp_sysc = { + .rev_offs = -ENODEV, .sysc_offs = 0x008c, .sysc_flags = (SYSC_HAS_CLOCKACTIVITY | SYSC_HAS_ENAWAKEUP | SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET), @@ -990,6 +991,7 @@ static struct omap_hwmod omap3xxx_mcbsp5_hwmod = { /* 'mcbsp sidetone' class */ static struct omap_hwmod_class_sysconfig omap3xxx_mcbsp_sidetone_sysc = { + .rev_offs = -ENODEV, .sysc_offs = 0x0010, .sysc_flags = SYSC_HAS_AUTOIDLE, .sysc_fields = &omap_hwmod_sysc_type1, @@ -1018,6 +1020,7 @@ static struct omap_hwmod omap3xxx_mcbsp3_sidetone_hwmod = { /* SR common */ static struct omap_hwmod_class_sysconfig omap34xx_sr_sysc = { + .rev_offs = -ENODEV, .sysc_offs = 0x24, .sysc_flags = (SYSC_HAS_CLOCKACTIVITY | SYSC_NO_CACHE), .sysc_fields = &omap34xx_sr_sysc_fields, @@ -1030,6 +1033,7 @@ static struct omap_hwmod_class omap34xx_smartreflex_hwmod_class = { }; static struct omap_hwmod_class_sysconfig omap36xx_sr_sysc = { + .rev_offs = -ENODEV, .sysc_offs = 0x38, .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART), .sysc_flags = (SYSC_HAS_SIDLEMODE | SYSC_HAS_ENAWAKEUP | diff --git a/arch/arm/mach-omap2/omap_hwmod_43xx_data.c b/arch/arm/mach-omap2/omap_hwmod_43xx_data.c index 5f73b730d4fc..aa271ac5ebac 100644 --- a/arch/arm/mach-omap2/omap_hwmod_43xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_43xx_data.c @@ -378,6 +378,7 @@ static struct omap_hwmod am43xx_usb_otg_ss1_hwmod = { }; static struct omap_hwmod_class_sysconfig am43xx_qspi_sysc = { + .rev_offs = 0, .sysc_offs = 0x0010, .sysc_flags = SYSC_HAS_SIDLEMODE, .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index e4f8ae9cd637..a95dbac57a81 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -23,7 +23,7 @@ #include <linux/io.h> #include <linux/platform_data/hsmmc-omap.h> #include <linux/power/smartreflex.h> -#include <linux/i2c-omap.h> +#include <linux/platform_data/i2c-omap.h> #include <linux/omap-dma.h> @@ -1360,6 +1360,7 @@ static struct omap_hwmod omap44xx_hsi_hwmod = { */ static struct omap_hwmod_class_sysconfig omap44xx_i2c_sysc = { + .rev_offs = 0, .sysc_offs = 0x0010, .syss_offs = 0x0090, .sysc_flags = (SYSC_HAS_AUTOIDLE | SYSC_HAS_CLOCKACTIVITY | @@ -1634,6 +1635,7 @@ static struct omap_hwmod omap44xx_mailbox_hwmod = { /* The IP is not compliant to type1 / type2 scheme */ static struct omap_hwmod_class_sysconfig omap44xx_mcasp_sysc = { + .rev_offs = 0, .sysc_offs = 0x0004, .sysc_flags = SYSC_HAS_SIDLEMODE, .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | @@ -1667,6 +1669,7 @@ static struct omap_hwmod omap44xx_mcasp_hwmod = { */ static struct omap_hwmod_class_sysconfig omap44xx_mcbsp_sysc = { + .rev_offs = -ENODEV, .sysc_offs = 0x008c, .sysc_flags = (SYSC_HAS_CLOCKACTIVITY | SYSC_HAS_ENAWAKEUP | SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET), @@ -2353,6 +2356,7 @@ static struct omap_hwmod omap44xx_slimbus2_hwmod = { /* The IP is not compliant to type1 / type2 scheme */ static struct omap_hwmod_class_sysconfig omap44xx_smartreflex_sysc = { + .rev_offs = -ENODEV, .sysc_offs = 0x0038, .sysc_flags = (SYSC_HAS_ENAWAKEUP | SYSC_HAS_SIDLEMODE), .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | diff --git a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c index c72cd84b07ec..115473d441cd 100644 --- a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c @@ -20,7 +20,7 @@ #include <linux/io.h> #include <linux/platform_data/hsmmc-omap.h> #include <linux/power/smartreflex.h> -#include <linux/i2c-omap.h> +#include <linux/platform_data/i2c-omap.h> #include <linux/omap-dma.h> @@ -804,6 +804,7 @@ static struct omap_hwmod omap54xx_gpio8_hwmod = { */ static struct omap_hwmod_class_sysconfig omap54xx_i2c_sysc = { + .rev_offs = 0, .sysc_offs = 0x0010, .syss_offs = 0x0090, .sysc_flags = (SYSC_HAS_AUTOIDLE | SYSC_HAS_CLOCKACTIVITY | @@ -974,6 +975,7 @@ static struct omap_hwmod omap54xx_mailbox_hwmod = { */ static struct omap_hwmod_class_sysconfig omap54xx_mcbsp_sysc = { + .rev_offs = -ENODEV, .sysc_offs = 0x008c, .sysc_flags = (SYSC_HAS_CLOCKACTIVITY | SYSC_HAS_ENAWAKEUP | SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET), @@ -1997,6 +1999,7 @@ static struct omap_hwmod omap54xx_ocp2scp3_hwmod = { */ static struct omap_hwmod_class_sysconfig omap54xx_sata_sysc = { + .rev_offs = 0x00fc, .sysc_offs = 0x0000, .sysc_flags = (SYSC_HAS_MIDLEMODE | SYSC_HAS_SIDLEMODE), .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | diff --git a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c index 62352d1e6361..e6c7061a8e73 100644 --- a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c @@ -20,7 +20,7 @@ #include <linux/io.h> #include <linux/platform_data/hsmmc-omap.h> #include <linux/power/smartreflex.h> -#include <linux/i2c-omap.h> +#include <linux/platform_data/i2c-omap.h> #include <linux/omap-dma.h> @@ -1070,6 +1070,7 @@ static struct omap_hwmod dra7xx_hdq1w_hwmod = { */ static struct omap_hwmod_class_sysconfig dra7xx_i2c_sysc = { + .rev_offs = 0, .sysc_offs = 0x0010, .syss_offs = 0x0090, .sysc_flags = (SYSC_HAS_AUTOIDLE | SYSC_HAS_CLOCKACTIVITY | @@ -1440,6 +1441,7 @@ static struct omap_hwmod dra7xx_mcspi4_hwmod = { * */ static struct omap_hwmod_class_sysconfig dra7xx_mcasp_sysc = { + .rev_offs = 0, .sysc_offs = 0x0004, .sysc_flags = SYSC_HAS_SIDLEMODE, .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART), @@ -1898,6 +1900,7 @@ static struct omap_hwmod dra7xx_pciess2_hwmod = { */ static struct omap_hwmod_class_sysconfig dra7xx_qspi_sysc = { + .rev_offs = 0, .sysc_offs = 0x0010, .sysc_flags = SYSC_HAS_SIDLEMODE, .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | @@ -1930,6 +1933,7 @@ static struct omap_hwmod dra7xx_qspi_hwmod = { * */ static struct omap_hwmod_class_sysconfig dra7xx_rtcss_sysc = { + .rev_offs = 0x0074, .sysc_offs = 0x0078, .sysc_flags = SYSC_HAS_SIDLEMODE, .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | @@ -1965,6 +1969,7 @@ static struct omap_hwmod dra7xx_rtcss_hwmod = { */ static struct omap_hwmod_class_sysconfig dra7xx_sata_sysc = { + .rev_offs = 0x00fc, .sysc_offs = 0x0000, .sysc_flags = (SYSC_HAS_MIDLEMODE | SYSC_HAS_SIDLEMODE), .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | @@ -2003,6 +2008,7 @@ static struct omap_hwmod dra7xx_sata_hwmod = { /* The IP is not compliant to type1 / type2 scheme */ static struct omap_hwmod_class_sysconfig dra7xx_smartreflex_sysc = { + .rev_offs = -ENODEV, .sysc_offs = 0x0038, .sysc_flags = (SYSC_HAS_ENAWAKEUP | SYSC_HAS_SIDLEMODE), .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | diff --git a/arch/arm/mach-omap2/omap_hwmod_81xx_data.c b/arch/arm/mach-omap2/omap_hwmod_81xx_data.c index 686655f884c1..8e44e2728620 100644 --- a/arch/arm/mach-omap2/omap_hwmod_81xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_81xx_data.c @@ -954,6 +954,7 @@ static struct omap_hwmod_ocp_if dm816x_l4_hs__emac1 = { }; static struct omap_hwmod_class_sysconfig dm81xx_sata_sysc = { + .rev_offs = 0x00fc, .sysc_offs = 0x1100, .sysc_flags = SYSC_HAS_SIDLEMODE, .idlemodes = SIDLE_FORCE, diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c index 6459816c2879..7f02743edbe4 100644 --- a/arch/arm/mach-omap2/pdata-quirks.c +++ b/arch/arm/mach-omap2/pdata-quirks.c @@ -26,14 +26,12 @@ #include <linux/platform_data/iommu-omap.h> #include <linux/platform_data/ti-sysc.h> #include <linux/platform_data/wkup_m3.h> -#include <linux/platform_data/media/ir-rx51.h> #include <linux/platform_data/asoc-ti-mcbsp.h> #include "common.h" #include "common-board-devices.h" #include "control.h" #include "omap_device.h" -#include "omap-pm.h" #include "omap-secure.h" #include "soc.h" #include "hsmmc.h" @@ -514,18 +512,6 @@ void omap_auxdata_legacy_init(struct device *dev) dev->platform_data = &twl_gpio_auxdata; } -static struct ir_rx51_platform_data __maybe_unused rx51_ir_data = { - .set_max_mpu_wakeup_lat = omap_pm_set_max_mpu_wakeup_lat, -}; - -static struct platform_device __maybe_unused rx51_ir_device = { - .name = "ir_rx51", - .id = -1, - .dev = { - .platform_data = &rx51_ir_data, - }, -}; - #if IS_ENABLED(CONFIG_SND_OMAP_SOC_MCBSP) static struct omap_mcbsp_platform_data mcbsp_pdata; static void __init omap3_mcbsp_init(void) @@ -569,7 +555,6 @@ static struct of_dev_auxdata omap_auxdata_lookup[] = { "480c9000.smartreflex", &omap_sr_pdata[OMAP_SR_MPU]), OF_DEV_AUXDATA("ti,omap3-hsmmc", 0x4809c000, "4809c000.mmc", &mmc_pdata[0]), OF_DEV_AUXDATA("ti,omap3-hsmmc", 0x480b4000, "480b4000.mmc", &mmc_pdata[1]), - OF_DEV_AUXDATA("nokia,n900-ir", 0, "n900-ir", &rx51_ir_data), /* Only on am3517 */ OF_DEV_AUXDATA("ti,davinci_mdio", 0x5c030000, "davinci_mdio.0", NULL), OF_DEV_AUXDATA("ti,am3517-emac", 0x5c000000, "davinci_emac.0", diff --git a/arch/arm/mach-omap2/pm-debug.c b/arch/arm/mach-omap2/pm-debug.c index 5c46ea6756d7..acb698d5780f 100644 --- a/arch/arm/mach-omap2/pm-debug.c +++ b/arch/arm/mach-omap2/pm-debug.c @@ -31,7 +31,6 @@ #include "clock.h" #include "powerdomain.h" #include "clockdomain.h" -#include "omap-pm.h" #include "soc.h" #include "cm2xxx_3xxx.h" @@ -240,10 +239,6 @@ static int option_set(void *data, u64 val) *option = val; if (option == &enable_off_mode) { - if (val) - omap_pm_enable_off_mode(); - else - omap_pm_disable_off_mode(); if (cpu_is_omap34xx()) omap3_pm_off_mode_enable(val); } diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c index 6f68576e5695..ca03af8fe43f 100644 --- a/arch/arm/mach-omap2/pm.c +++ b/arch/arm/mach-omap2/pm.c @@ -16,11 +16,11 @@ #include <linux/pm_opp.h> #include <linux/export.h> #include <linux/suspend.h> +#include <linux/clk.h> #include <linux/cpu.h> #include <asm/system_misc.h> -#include "omap-pm.h" #include "omap_device.h" #include "common.h" @@ -230,16 +230,20 @@ static void __init omap4_init_voltages(void) omap2_set_init_voltage("iva", "dpll_iva_m5x2_ck", "iva"); } -static int __init omap2_common_pm_init(void) +int __maybe_unused omap_pm_nop_init(void) { - omap_pm_if_init(); - return 0; } -omap_postcore_initcall(omap2_common_pm_init); + +int (*omap_pm_soc_init)(void); int __init omap2_common_pm_late_init(void) { + int error; + + if (!omap_pm_soc_init) + return 0; + /* Init the voltage layer */ omap3_twl_init(); omap4_twl_init(); @@ -252,5 +256,12 @@ int __init omap2_common_pm_late_init(void) /* Smartreflex device init */ omap_devinit_smartreflex(); + error = omap_pm_soc_init(); + if (error) + pr_warn("%s: pm soc init failed: %i\n", __func__, error); + + omap2_clk_enable_autoidle_all(); + return 0; } +omap_late_initcall(omap2_common_pm_late_init); diff --git a/arch/arm/mach-omap2/pm33xx-core.c b/arch/arm/mach-omap2/pm33xx-core.c index 93c0b5ba9f09..9b3755a2e2ec 100644 --- a/arch/arm/mach-omap2/pm33xx-core.c +++ b/arch/arm/mach-omap2/pm33xx-core.c @@ -173,7 +173,7 @@ static struct am33xx_pm_platform_data *am33xx_pm_get_pdata(void) return NULL; } -void __init amx3_common_pm_init(void) +int __init amx3_common_pm_init(void) { struct am33xx_pm_platform_data *pdata; struct platform_device_info devinfo; @@ -186,4 +186,6 @@ void __init amx3_common_pm_init(void) devinfo.size_data = sizeof(*pdata); devinfo.id = -1; platform_device_register_full(&devinfo); + + return 0; } diff --git a/arch/arm/mach-omap2/pm44xx.c b/arch/arm/mach-omap2/pm44xx.c index b3870220612e..78e1ace7d17d 100644 --- a/arch/arm/mach-omap2/pm44xx.c +++ b/arch/arm/mach-omap2/pm44xx.c @@ -131,6 +131,19 @@ static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused) return 0; } + /* + * Bootloader or kexec boot may have LOGICRETSTATE cleared + * for some domains. This is the case when kexec booting from + * Android kernels that support off mode for example. + * Make sure it's set at least for core and per, otherwise + * we currently will see lost GPIO interrupts for wlcore and + * smsc911x at least if per hits retention during idle. + */ + if (!strncmp(pwrdm->name, "core", 4) || + !strncmp(pwrdm->name, "l4per", 5) || + !strncmp(pwrdm->name, "wkup", 4)) + pwrdm_set_logic_retst(pwrdm, PWRDM_POWER_RET); + pwrst = kmalloc(sizeof(struct power_state), GFP_ATOMIC); if (!pwrst) return -ENOMEM; diff --git a/arch/arm/mach-omap2/powerdomain.c b/arch/arm/mach-omap2/powerdomain.c index 76eb6ec5f157..1a0f69c0a376 100644 --- a/arch/arm/mach-omap2/powerdomain.c +++ b/arch/arm/mach-omap2/powerdomain.c @@ -14,6 +14,7 @@ */ #undef DEBUG +#include <linux/cpu_pm.h> #include <linux/kernel.h> #include <linux/types.h> #include <linux/list.h> @@ -39,6 +40,9 @@ #define PWRDM_TRACE_STATES_FLAG (1<<31) +void pwrdms_save_context(void); +void pwrdms_restore_context(void); + enum { PWRDM_STATE_NOW = 0, PWRDM_STATE_PREV, @@ -188,7 +192,7 @@ static int _pwrdm_state_switch(struct powerdomain *pwrdm, int flag) ((prev & OMAP_POWERSTATE_MASK) << 0)); trace_power_domain_target_rcuidle(pwrdm->name, trace_state, - smp_processor_id()); + raw_smp_processor_id()); } break; default: @@ -333,6 +337,22 @@ int pwrdm_register_pwrdms(struct powerdomain **ps) return 0; } +static int cpu_notifier(struct notifier_block *nb, unsigned long cmd, void *v) +{ + switch (cmd) { + case CPU_CLUSTER_PM_ENTER: + if (enable_off_mode) + pwrdms_save_context(); + break; + case CPU_CLUSTER_PM_EXIT: + if (enable_off_mode) + pwrdms_restore_context(); + break; + } + + return NOTIFY_OK; +} + /** * pwrdm_complete_init - set up the powerdomain layer * @@ -347,6 +367,7 @@ int pwrdm_register_pwrdms(struct powerdomain **ps) int pwrdm_complete_init(void) { struct powerdomain *temp_p; + static struct notifier_block nb; if (list_empty(&pwrdm_list)) return -EACCES; @@ -354,6 +375,12 @@ int pwrdm_complete_init(void) list_for_each_entry(temp_p, &pwrdm_list, node) pwrdm_set_next_pwrst(temp_p, PWRDM_POWER_ON); + /* Only AM43XX can lose pwrdm context during rtc-ddr suspend */ + if (soc_is_am43xx()) { + nb.notifier_call = cpu_notifier; + cpu_pm_register_notifier(&nb); + } + return 0; } @@ -518,7 +545,7 @@ int pwrdm_set_next_pwrst(struct powerdomain *pwrdm, u8 pwrst) if (arch_pwrdm && arch_pwrdm->pwrdm_set_next_pwrst) { /* Trace the pwrdm desired target state */ trace_power_domain_target_rcuidle(pwrdm->name, pwrst, - smp_processor_id()); + raw_smp_processor_id()); /* Program the pwrdm desired target state */ ret = arch_pwrdm->pwrdm_set_next_pwrst(pwrdm, pwrst); } @@ -1199,3 +1226,63 @@ bool pwrdm_can_ever_lose_context(struct powerdomain *pwrdm) return 0; } + +/** + * pwrdm_save_context - save powerdomain registers + * + * Register state is going to be lost due to a suspend or hibernate + * event. Save the powerdomain registers. + */ +static int pwrdm_save_context(struct powerdomain *pwrdm, void *unused) +{ + if (arch_pwrdm && arch_pwrdm->pwrdm_save_context) + arch_pwrdm->pwrdm_save_context(pwrdm); + return 0; +} + +/** + * pwrdm_save_context - restore powerdomain registers + * + * Restore powerdomain control registers after a suspend or resume + * event. + */ +static int pwrdm_restore_context(struct powerdomain *pwrdm, void *unused) +{ + if (arch_pwrdm && arch_pwrdm->pwrdm_restore_context) + arch_pwrdm->pwrdm_restore_context(pwrdm); + return 0; +} + +static int pwrdm_lost_power(struct powerdomain *pwrdm, void *unused) +{ + int state; + + /* + * Power has been lost across all powerdomains, increment the + * counter. + */ + + state = pwrdm_read_pwrst(pwrdm); + if (state != PWRDM_POWER_OFF) { + pwrdm->state_counter[state]++; + pwrdm->state_counter[PWRDM_POWER_OFF]++; + } + pwrdm->state = state; + + return 0; +} + +void pwrdms_save_context(void) +{ + pwrdm_for_each(pwrdm_save_context, NULL); +} + +void pwrdms_restore_context(void) +{ + pwrdm_for_each(pwrdm_restore_context, NULL); +} + +void pwrdms_lost_power(void) +{ + pwrdm_for_each(pwrdm_lost_power, NULL); +} diff --git a/arch/arm/mach-omap2/powerdomain.h b/arch/arm/mach-omap2/powerdomain.h index 28a796ce07d7..9a907fb14044 100644 --- a/arch/arm/mach-omap2/powerdomain.h +++ b/arch/arm/mach-omap2/powerdomain.h @@ -144,6 +144,7 @@ struct powerdomain { s64 timer; s64 state_timer[PWRDM_MAX_PWRSTS]; #endif + u32 context; }; /** @@ -198,6 +199,8 @@ struct pwrdm_ops { int (*pwrdm_set_lowpwrstchange)(struct powerdomain *pwrdm); int (*pwrdm_wait_transition)(struct powerdomain *pwrdm); int (*pwrdm_has_voltdm)(void); + void (*pwrdm_save_context)(struct powerdomain *pwrdm); + void (*pwrdm_restore_context)(struct powerdomain *pwrdm); }; int pwrdm_register_platform_funcs(struct pwrdm_ops *custom_funcs); @@ -273,4 +276,8 @@ extern struct powerdomain gfx_omap2_pwrdm; extern void pwrdm_lock(struct powerdomain *pwrdm); extern void pwrdm_unlock(struct powerdomain *pwrdm); +extern void pwrdms_save_context(void); +extern void pwrdms_restore_context(void); + +extern void pwrdms_lost_power(void); #endif diff --git a/arch/arm/mach-omap2/prm33xx.c b/arch/arm/mach-omap2/prm33xx.c index ebaf80d72a10..d5141669c28d 100644 --- a/arch/arm/mach-omap2/prm33xx.c +++ b/arch/arm/mach-omap2/prm33xx.c @@ -342,6 +342,35 @@ static void am33xx_prm_global_warm_sw_reset(void) AM33XX_PRM_RSTCTRL_OFFSET); } +static void am33xx_pwrdm_save_context(struct powerdomain *pwrdm) +{ + pwrdm->context = am33xx_prm_read_reg(pwrdm->prcm_offs, + pwrdm->pwrstctrl_offs); + /* + * Do not save LOWPOWERSTATECHANGE, writing a 1 indicates a request, + * reading back a 1 indicates a request in progress. + */ + pwrdm->context &= ~AM33XX_LOWPOWERSTATECHANGE_MASK; +} + +static void am33xx_pwrdm_restore_context(struct powerdomain *pwrdm) +{ + int st, ctrl; + + st = am33xx_prm_read_reg(pwrdm->prcm_offs, + pwrdm->pwrstst_offs); + + am33xx_prm_write_reg(pwrdm->context, pwrdm->prcm_offs, + pwrdm->pwrstctrl_offs); + + /* Make sure we only wait for a transition if there is one */ + st &= OMAP_POWERSTATEST_MASK; + ctrl = OMAP_POWERSTATEST_MASK & pwrdm->context; + + if (st != ctrl) + am33xx_pwrdm_wait_transition(pwrdm); +} + struct pwrdm_ops am33xx_pwrdm_operations = { .pwrdm_set_next_pwrst = am33xx_pwrdm_set_next_pwrst, .pwrdm_read_next_pwrst = am33xx_pwrdm_read_next_pwrst, @@ -357,6 +386,8 @@ struct pwrdm_ops am33xx_pwrdm_operations = { .pwrdm_set_mem_retst = am33xx_pwrdm_set_mem_retst, .pwrdm_wait_transition = am33xx_pwrdm_wait_transition, .pwrdm_has_voltdm = am33xx_check_vcvp, + .pwrdm_save_context = am33xx_pwrdm_save_context, + .pwrdm_restore_context = am33xx_pwrdm_restore_context, }; static struct prm_ll_data am33xx_prm_ll_data = { diff --git a/arch/arm/mach-omap2/prm44xx.c b/arch/arm/mach-omap2/prm44xx.c index acb95936dfe7..7b95729e8359 100644 --- a/arch/arm/mach-omap2/prm44xx.c +++ b/arch/arm/mach-omap2/prm44xx.c @@ -12,6 +12,7 @@ * published by the Free Software Foundation. */ +#include <linux/cpu_pm.h> #include <linux/kernel.h> #include <linux/delay.h> #include <linux/errno.h> @@ -30,6 +31,7 @@ #include "prcm44xx.h" #include "prminst44xx.h" #include "powerdomain.h" +#include "pm.h" /* Static data */ @@ -57,6 +59,13 @@ static struct omap_prcm_irq_setup omap4_prcm_irq_setup = { .reconfigure_io_chain = &omap44xx_prm_reconfigure_io_chain, }; +struct omap_prm_irq_context { + unsigned long irq_enable; + unsigned long pm_ctrl; +}; + +static struct omap_prm_irq_context omap_prm_context; + /* * omap44xx_prm_reset_src_map - map from bits in the PRM_RSTST * hardware register (which are specific to OMAP44xx SoCs) to reset @@ -667,6 +676,54 @@ static int omap4_check_vcvp(void) return 0; } +/** + * omap4_pwrdm_save_context - Saves the powerdomain state + * @pwrdm: pointer to individual powerdomain + * + * The function saves the powerdomain state control information. + * This is needed in rtc+ddr modes where we lose powerdomain context. + */ +static void omap4_pwrdm_save_context(struct powerdomain *pwrdm) +{ + pwrdm->context = omap4_prminst_read_inst_reg(pwrdm->prcm_partition, + pwrdm->prcm_offs, + pwrdm->pwrstctrl_offs); + + /* + * Do not save LOWPOWERSTATECHANGE, writing a 1 indicates a request, + * reading back a 1 indicates a request in progress. + */ + pwrdm->context &= ~OMAP4430_LOWPOWERSTATECHANGE_MASK; +} + +/** + * omap4_pwrdm_restore_context - Restores the powerdomain state + * @pwrdm: pointer to individual powerdomain + * + * The function restores the powerdomain state control information. + * This is needed in rtc+ddr modes where we lose powerdomain context. + */ +static void omap4_pwrdm_restore_context(struct powerdomain *pwrdm) +{ + int st, ctrl; + + st = omap4_prminst_read_inst_reg(pwrdm->prcm_partition, + pwrdm->prcm_offs, + pwrdm->pwrstctrl_offs); + + omap4_prminst_write_inst_reg(pwrdm->context, + pwrdm->prcm_partition, + pwrdm->prcm_offs, + pwrdm->pwrstctrl_offs); + + /* Make sure we only wait for a transition if there is one */ + st &= OMAP_POWERSTATEST_MASK; + ctrl = OMAP_POWERSTATEST_MASK & pwrdm->context; + + if (st != ctrl) + omap4_pwrdm_wait_transition(pwrdm); +} + struct pwrdm_ops omap4_pwrdm_operations = { .pwrdm_set_next_pwrst = omap4_pwrdm_set_next_pwrst, .pwrdm_read_next_pwrst = omap4_pwrdm_read_next_pwrst, @@ -685,10 +742,50 @@ struct pwrdm_ops omap4_pwrdm_operations = { .pwrdm_set_mem_retst = omap4_pwrdm_set_mem_retst, .pwrdm_wait_transition = omap4_pwrdm_wait_transition, .pwrdm_has_voltdm = omap4_check_vcvp, + .pwrdm_save_context = omap4_pwrdm_save_context, + .pwrdm_restore_context = omap4_pwrdm_restore_context, }; static int omap44xx_prm_late_init(void); +void prm_save_context(void) +{ + omap_prm_context.irq_enable = + omap4_prm_read_inst_reg(AM43XX_PRM_OCP_SOCKET_INST, + omap4_prcm_irq_setup.mask); + + omap_prm_context.pm_ctrl = + omap4_prm_read_inst_reg(AM43XX_PRM_DEVICE_INST, + omap4_prcm_irq_setup.pm_ctrl); +} + +void prm_restore_context(void) +{ + omap4_prm_write_inst_reg(omap_prm_context.irq_enable, + OMAP4430_PRM_OCP_SOCKET_INST, + omap4_prcm_irq_setup.mask); + + omap4_prm_write_inst_reg(omap_prm_context.pm_ctrl, + AM43XX_PRM_DEVICE_INST, + omap4_prcm_irq_setup.pm_ctrl); +} + +static int cpu_notifier(struct notifier_block *nb, unsigned long cmd, void *v) +{ + switch (cmd) { + case CPU_CLUSTER_PM_ENTER: + if (enable_off_mode) + prm_save_context(); + break; + case CPU_CLUSTER_PM_EXIT: + if (enable_off_mode) + prm_restore_context(); + break; + } + + return NOTIFY_OK; +} + /* * XXX document */ @@ -709,6 +806,7 @@ static const struct omap_prcm_init_data *prm_init_data; int __init omap44xx_prm_init(const struct omap_prcm_init_data *data) { + static struct notifier_block nb; omap_prm_base_init(); prm_init_data = data; @@ -730,6 +828,12 @@ int __init omap44xx_prm_init(const struct omap_prcm_init_data *data) omap4_prcm_irq_setup.mask = AM43XX_PRM_IRQENABLE_MPU_OFFSET; } + /* Only AM43XX can lose prm context during rtc-ddr suspend */ + if (soc_is_am43xx()) { + nb.notifier_call = cpu_notifier; + cpu_pm_register_notifier(&nb); + } + return prm_register(&omap44xx_prm_ll_data); } diff --git a/arch/arm/mach-omap2/prm_common.c b/arch/arm/mach-omap2/prm_common.c index 021b5a8b9c0a..058a37e6d11c 100644 --- a/arch/arm/mach-omap2/prm_common.c +++ b/arch/arm/mach-omap2/prm_common.c @@ -285,10 +285,11 @@ int omap_prcm_register_chain_handler(struct omap_prcm_irq_setup *irq_setup) prcm_irq_setup = irq_setup; - prcm_irq_chips = kzalloc(sizeof(void *) * nr_regs, GFP_KERNEL); - prcm_irq_setup->saved_mask = kzalloc(sizeof(u32) * nr_regs, GFP_KERNEL); - prcm_irq_setup->priority_mask = kzalloc(sizeof(u32) * nr_regs, - GFP_KERNEL); + prcm_irq_chips = kcalloc(nr_regs, sizeof(void *), GFP_KERNEL); + prcm_irq_setup->saved_mask = kcalloc(nr_regs, sizeof(u32), + GFP_KERNEL); + prcm_irq_setup->priority_mask = kcalloc(nr_regs, sizeof(u32), + GFP_KERNEL); if (!prcm_irq_chips || !prcm_irq_setup->saved_mask || !prcm_irq_setup->priority_mask) diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c index 4fb4dc24e5e9..98ed5ac073bc 100644 --- a/arch/arm/mach-omap2/timer.c +++ b/arch/arm/mach-omap2/timer.c @@ -50,7 +50,6 @@ #include "omap_device.h" #include <plat/counter-32k.h> #include <clocksource/timer-ti-dm.h> -#include "omap-pm.h" #include "soc.h" #include "common.h" @@ -71,6 +70,9 @@ static struct clock_event_device clockevent_gpt; /* Clockevent hwmod for am335x and am437x suspend */ static struct omap_hwmod *clockevent_gpt_hwmod; +/* Clockesource hwmod for am437x suspend */ +static struct omap_hwmod *clocksource_gpt_hwmod; + #ifdef CONFIG_SOC_HAS_REALTIME_COUNTER static unsigned long arch_timer_freq; @@ -168,6 +170,43 @@ static const struct of_device_id omap_timer_match[] __initconst = { { } }; +static int omap_timer_add_disabled_property(struct device_node *np) +{ + struct property *prop; + + prop = kzalloc(sizeof(*prop), GFP_KERNEL); + if (!prop) + return -ENOMEM; + + prop->name = "status"; + prop->value = "disabled"; + prop->length = strlen(prop->value); + + return of_add_property(np, prop); +} + +static int omap_timer_update_dt(struct device_node *np) +{ + int error = 0; + + if (!of_device_is_compatible(np, "ti,omap-counter32k")) { + error = omap_timer_add_disabled_property(np); + if (error) + return error; + } + + /* No parent interconnect target module configured? */ + if (of_get_property(np, "ti,hwmods", NULL)) + return error; + + /* Tag parent interconnect target module disabled */ + error = omap_timer_add_disabled_property(np->parent); + if (error) + return error; + + return 0; +} + /** * omap_get_timer_dt - get a timer using device-tree * @match - device-tree match structure for matching a device type @@ -183,6 +222,7 @@ static struct device_node * __init omap_get_timer_dt(const struct of_device_id * const char *property) { struct device_node *np; + int error; for_each_matching_node(np, match) { if (!of_device_is_available(np)) @@ -197,17 +237,9 @@ static struct device_node * __init omap_get_timer_dt(const struct of_device_id * of_get_property(np, "ti,timer-secure", NULL))) continue; - if (!of_device_is_compatible(np, "ti,omap-counter32k")) { - struct property *prop; + error = omap_timer_update_dt(np); + WARN(error, "%s: Could not update dt: %i\n", __func__, error); - prop = kzalloc(sizeof(*prop), GFP_KERNEL); - if (!prop) - return NULL; - prop->name = "status"; - prop->value = "disabled"; - prop->length = strlen(prop->value); - of_add_property(np, prop); - } return np; } @@ -266,8 +298,12 @@ static int __init omap_dm_timer_init_one(struct omap_dm_timer *timer, return -ENODEV; of_property_read_string_index(np, "ti,hwmods", 0, &oh_name); - if (!oh_name) - return -ENODEV; + if (!oh_name) { + of_property_read_string_index(np->parent, "ti,hwmods", 0, + &oh_name); + if (!oh_name) + return -ENODEV; + } timer->irq = irq_of_parse_and_map(np, 0); if (!timer->irq) @@ -419,9 +455,12 @@ static int __init __maybe_unused omap2_sync32k_clocksource_init(void) if (!np) return -ENODEV; - of_property_read_string_index(np, "ti,hwmods", 0, &oh_name); - if (!oh_name) - return -ENODEV; + of_property_read_string_index(np->parent, "ti,hwmods", 0, &oh_name); + if (!oh_name) { + of_property_read_string_index(np, "ti,hwmods", 0, &oh_name); + if (!oh_name) + return -ENODEV; + } /* * First check hwmod data is available for sync32k counter @@ -442,6 +481,26 @@ static int __init __maybe_unused omap2_sync32k_clocksource_init(void) return ret; } +static unsigned int omap2_gptimer_clksrc_load; + +static void omap2_gptimer_clksrc_suspend(struct clocksource *unused) +{ + omap2_gptimer_clksrc_load = + __omap_dm_timer_read_counter(&clksrc, OMAP_TIMER_NONPOSTED); + + omap_hwmod_idle(clocksource_gpt_hwmod); +} + +static void omap2_gptimer_clksrc_resume(struct clocksource *unused) +{ + omap_hwmod_enable(clocksource_gpt_hwmod); + + __omap_dm_timer_load_start(&clksrc, + OMAP_TIMER_CTRL_ST | OMAP_TIMER_CTRL_AR, + omap2_gptimer_clksrc_load, + OMAP_TIMER_NONPOSTED); +} + static void __init omap2_gptimer_clocksource_init(int gptimer_id, const char *fck_source, const char *property) @@ -454,6 +513,15 @@ static void __init omap2_gptimer_clocksource_init(int gptimer_id, res = omap_dm_timer_init_one(&clksrc, fck_source, property, &clocksource_gpt.name, OMAP_TIMER_NONPOSTED); + + if (soc_is_am43xx()) { + clocksource_gpt.suspend = omap2_gptimer_clksrc_suspend; + clocksource_gpt.resume = omap2_gptimer_clksrc_resume; + + clocksource_gpt_hwmod = + omap_hwmod_lookup(clocksource_gpt.name); + } + BUG_ON(res); __omap_dm_timer_load_start(&clksrc, diff --git a/arch/arm/mach-pxa/palmz72.c b/arch/arm/mach-pxa/palmz72.c index 5877e547cecd..4d475f6f4a77 100644 --- a/arch/arm/mach-pxa/palmz72.c +++ b/arch/arm/mach-pxa/palmz72.c @@ -30,7 +30,7 @@ #include <linux/wm97xx.h> #include <linux/power_supply.h> #include <linux/usb/gpio_vbus.h> -#include <linux/i2c-gpio.h> +#include <linux/platform_data/i2c-gpio.h> #include <linux/gpio/machine.h> #include <asm/mach-types.h> @@ -322,7 +322,7 @@ static struct soc_camera_link palmz72_iclink = { }; static struct gpiod_lookup_table palmz72_i2c_gpiod_table = { - .dev_id = "i2c-gpio", + .dev_id = "i2c-gpio.0", .table = { GPIO_LOOKUP_IDX("gpio-pxa", 118, NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), diff --git a/arch/arm/mach-pxa/pxa3xx.c b/arch/arm/mach-pxa/pxa3xx.c index 4b8a0df8ea57..8c64f93b669b 100644 --- a/arch/arm/mach-pxa/pxa3xx.c +++ b/arch/arm/mach-pxa/pxa3xx.c @@ -446,6 +446,10 @@ static int __init pxa3xx_init(void) pxa3xx_init_pm(); + enable_irq_wake(IRQ_WAKEUP0); + if (cpu_is_pxa320()) + enable_irq_wake(IRQ_WAKEUP1); + register_syscore_ops(&pxa_irq_syscore_ops); register_syscore_ops(&pxa3xx_mfp_syscore_ops); diff --git a/arch/arm/mach-pxa/stargate2.c b/arch/arm/mach-pxa/stargate2.c index df62bb23dbee..bbea5fa9a140 100644 --- a/arch/arm/mach-pxa/stargate2.c +++ b/arch/arm/mach-pxa/stargate2.c @@ -27,11 +27,11 @@ #include <linux/platform_data/i2c-pxa.h> #include <linux/platform_data/pcf857x.h> -#include <linux/platform_data/at24.h> #include <linux/smc91x.h> #include <linux/gpio/machine.h> #include <linux/gpio.h> #include <linux/leds.h> +#include <linux/property.h> #include <asm/types.h> #include <asm/setup.h> @@ -795,9 +795,9 @@ static struct pcf857x_platform_data platform_data_pcf857x = { .context = NULL, }; -static struct at24_platform_data pca9500_eeprom_pdata = { - .byte_len = 256, - .page_size = 4, +static const struct property_entry pca9500_eeprom_properties[] = { + PROPERTY_ENTRY_U32("pagesize", 4), + { } }; /** @@ -935,7 +935,7 @@ static struct i2c_board_info __initdata stargate2_i2c_board_info[] = { }, { .type = "24c02", .addr = 0x57, - .platform_data = &pca9500_eeprom_pdata, + .properties = pca9500_eeprom_properties, }, { .type = "max1238", .addr = 0x35, diff --git a/arch/arm/mach-pxa/viper.c b/arch/arm/mach-pxa/viper.c index 90d0f277de55..ab2f89266bbd 100644 --- a/arch/arm/mach-pxa/viper.c +++ b/arch/arm/mach-pxa/viper.c @@ -35,7 +35,7 @@ #include <linux/sched.h> #include <linux/gpio.h> #include <linux/jiffies.h> -#include <linux/i2c-gpio.h> +#include <linux/platform_data/i2c-gpio.h> #include <linux/gpio/machine.h> #include <linux/platform_data/i2c-pxa.h> #include <linux/serial_8250.h> @@ -460,7 +460,7 @@ static struct platform_device smc91x_device = { /* i2c */ static struct gpiod_lookup_table viper_i2c_gpiod_table = { - .dev_id = "i2c-gpio", + .dev_id = "i2c-gpio.1", .table = { GPIO_LOOKUP_IDX("gpio-pxa", VIPER_RTC_I2C_SDA_GPIO, NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), @@ -789,7 +789,7 @@ static int __init viper_tpm_setup(char *str) __setup("tpm=", viper_tpm_setup); struct gpiod_lookup_table viper_tpm_i2c_gpiod_table = { - .dev_id = "i2c-gpio", + .dev_id = "i2c-gpio.2", .table = { GPIO_LOOKUP_IDX("gpio-pxa", VIPER_TPM_I2C_SDA_GPIO, NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), diff --git a/arch/arm/mach-rockchip/Kconfig b/arch/arm/mach-rockchip/Kconfig index a4065966881a..fafd3d7f9f8c 100644 --- a/arch/arm/mach-rockchip/Kconfig +++ b/arch/arm/mach-rockchip/Kconfig @@ -3,7 +3,6 @@ config ARCH_ROCKCHIP depends on ARCH_MULTI_V7 select PINCTRL select PINCTRL_ROCKCHIP - select ARCH_DMA_ADDR_T_64BIT if ARM_LPAE select ARCH_HAS_RESET_CONTROLLER select ARM_AMBA select ARM_GIC diff --git a/arch/arm/mach-rpc/ecard.c b/arch/arm/mach-rpc/ecard.c index bdb5ec1cf560..39aef4876ed4 100644 --- a/arch/arm/mach-rpc/ecard.c +++ b/arch/arm/mach-rpc/ecard.c @@ -657,25 +657,13 @@ static int ecard_devices_proc_show(struct seq_file *m, void *v) return 0; } -static int ecard_devices_proc_open(struct inode *inode, struct file *file) -{ - return single_open(file, ecard_devices_proc_show, NULL); -} - -static const struct file_operations bus_ecard_proc_fops = { - .owner = THIS_MODULE, - .open = ecard_devices_proc_open, - .read = seq_read, - .llseek = seq_lseek, - .release = single_release, -}; - static struct proc_dir_entry *proc_bus_ecard_dir = NULL; static void ecard_proc_init(void) { proc_bus_ecard_dir = proc_mkdir("bus/ecard", NULL); - proc_create("devices", 0, proc_bus_ecard_dir, &bus_ecard_proc_fops); + proc_create_single("devices", 0, proc_bus_ecard_dir, + ecard_devices_proc_show); } #define ec_set_resource(ec,nr,st,sz) \ diff --git a/arch/arm/mach-s3c24xx/h1940-bluetooth.c b/arch/arm/mach-s3c24xx/h1940-bluetooth.c index 46ad20ea87d1..186b5321658e 100644 --- a/arch/arm/mach-s3c24xx/h1940-bluetooth.c +++ b/arch/arm/mach-s3c24xx/h1940-bluetooth.c @@ -1,4 +1,4 @@ -// SPDX-License-Identifier: GPL-1.0 +// SPDX-License-Identifier: GPL-1.0+ // // Copyright (c) Arnaud Patard <arnaud.patard@rtp-net.org> // diff --git a/arch/arm/mach-s3c24xx/mach-mini2440.c b/arch/arm/mach-s3c24xx/mach-mini2440.c index 95753e0bc073..f9fc1f8d2b28 100644 --- a/arch/arm/mach-s3c24xx/mach-mini2440.c +++ b/arch/arm/mach-s3c24xx/mach-mini2440.c @@ -20,7 +20,7 @@ #include <linux/serial_core.h> #include <linux/serial_s3c.h> #include <linux/dm9000.h> -#include <linux/platform_data/at24.h> +#include <linux/property.h> #include <linux/platform_device.h> #include <linux/gpio_keys.h> #include <linux/i2c.h> @@ -481,15 +481,15 @@ static struct platform_device mini2440_audio = { /* * I2C devices */ -static struct at24_platform_data at24c08 = { - .byte_len = SZ_8K / 8, - .page_size = 16, +static const struct property_entry mini2440_at24_properties[] = { + PROPERTY_ENTRY_U32("pagesize", 16), + { } }; static struct i2c_board_info mini2440_i2c_devs[] __initdata = { { I2C_BOARD_INFO("24c08", 0x50), - .platform_data = &at24c08, + .properties = mini2440_at24_properties, }, }; diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c64xx/mach-crag6410-module.c index f00988705408..5aa472892465 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410-module.c @@ -9,6 +9,7 @@ #include <linux/interrupt.h> #include <linux/i2c.h> #include <linux/spi/spi.h> +#include <linux/gpio/machine.h> #include <linux/mfd/wm831x/irq.h> #include <linux/mfd/wm831x/gpio.h> @@ -206,9 +207,6 @@ static const struct i2c_board_info wm1277_devs[] = { }; static struct arizona_pdata wm5102_reva_pdata = { - .ldo1 = { - .ldoena = S3C64XX_GPN(7), - }, .gpio_base = CODEC_GPIO_BASE, .irq_flags = IRQF_TRIGGER_HIGH, .micd_pol_gpio = CODEC_GPIO_BASE + 4, @@ -237,10 +235,16 @@ static struct spi_board_info wm5102_reva_spi_devs[] = { }, }; -static struct arizona_pdata wm5102_pdata = { - .ldo1 = { - .ldoena = S3C64XX_GPN(7), +static struct gpiod_lookup_table wm5102_reva_gpiod_table = { + .dev_id = "spi0.1", /* SPI device name */ + .table = { + GPIO_LOOKUP("GPION", 7, + "wlf,ldoena", GPIO_ACTIVE_HIGH), + { }, }, +}; + +static struct arizona_pdata wm5102_pdata = { .gpio_base = CODEC_GPIO_BASE, .irq_flags = IRQF_TRIGGER_HIGH, .micd_pol_gpio = CODEC_GPIO_BASE + 2, @@ -264,6 +268,15 @@ static struct spi_board_info wm5102_spi_devs[] = { }, }; +static struct gpiod_lookup_table wm5102_gpiod_table = { + .dev_id = "spi0.1", /* SPI device name */ + .table = { + GPIO_LOOKUP("GPION", 7, + "wlf,ldo1ena", GPIO_ACTIVE_HIGH), + { }, + }, +}; + static struct spi_board_info wm5110_spi_devs[] = { [0] = { .modalias = "wm5110", @@ -366,6 +379,9 @@ static int wlf_gf_module_probe(struct i2c_client *i2c, rev == gf_mods[i].rev)) break; + gpiod_add_lookup_table(&wm5102_reva_gpiod_table); + gpiod_add_lookup_table(&wm5102_gpiod_table); + if (i < ARRAY_SIZE(gf_mods)) { dev_info(&i2c->dev, "%s revision %d\n", gf_mods[i].name, rev + 1); diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c index ace010479eb6..406487e76a5c 100644 --- a/arch/arm/mach-sa1100/simpad.c +++ b/arch/arm/mach-sa1100/simpad.c @@ -37,7 +37,7 @@ #include <linux/input.h> #include <linux/gpio_keys.h> #include <linux/leds.h> -#include <linux/i2c-gpio.h> +#include <linux/platform_data/i2c-gpio.h> #include "generic.h" @@ -327,7 +327,7 @@ static struct platform_device simpad_gpio_leds = { * i2c */ static struct gpiod_lookup_table simpad_i2c_gpiod_table = { - .dev_id = "i2c-gpio", + .dev_id = "i2c-gpio.0", .table = { GPIO_LOOKUP_IDX("gpio", 21, NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN), diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig index 280e7312a9e1..0b67254eabb2 100644 --- a/arch/arm/mach-shmobile/Kconfig +++ b/arch/arm/mach-shmobile/Kconfig @@ -29,7 +29,6 @@ config ARCH_RMOBILE menuconfig ARCH_RENESAS bool "Renesas ARM SoCs" depends on ARCH_MULTI_V7 && MMU - select ARCH_DMA_ADDR_T_64BIT if ARM_LPAE select ARCH_SHMOBILE select ARM_GIC select GPIOLIB @@ -75,6 +74,10 @@ config ARCH_R8A7745 bool "RZ/G1E (R8A77450)" select ARCH_RCAR_GEN2 +config ARCH_R8A77470 + bool "RZ/G1C (R8A77470)" + select ARCH_RCAR_GEN2 + config ARCH_R8A7778 bool "R-Car M1A (R8A77781)" select ARCH_RCAR_GEN1 @@ -110,6 +113,15 @@ config ARCH_R8A7794 bool "R-Car E2 (R8A77940)" select ARCH_RCAR_GEN2 +config ARCH_R9A06G032 + bool "RZ/N1D (R9A06G032)" + select ARCH_RZN1 + +config ARCH_RZN1 + bool "RZ/N1 (R9A06G0xx) Family" + select ARM_AMBA + select CPU_V7 + config ARCH_SH73A0 bool "SH-Mobile AG5 (R8A73A00)" select ARCH_RMOBILE diff --git a/arch/arm/mach-shmobile/common.h b/arch/arm/mach-shmobile/common.h index 43c1ac696274..2109f123bdfb 100644 --- a/arch/arm/mach-shmobile/common.h +++ b/arch/arm/mach-shmobile/common.h @@ -2,7 +2,6 @@ #ifndef __ARCH_MACH_COMMON_H #define __ARCH_MACH_COMMON_H -extern void shmobile_init_cntvoff(void); extern void shmobile_init_delay(void); extern void shmobile_boot_vector(void); extern unsigned long shmobile_boot_fn; diff --git a/arch/arm/mach-shmobile/headsmp-apmu.S b/arch/arm/mach-shmobile/headsmp-apmu.S index 5672b5849401..d49ab194766a 100644 --- a/arch/arm/mach-shmobile/headsmp-apmu.S +++ b/arch/arm/mach-shmobile/headsmp-apmu.S @@ -11,29 +11,9 @@ #include <linux/linkage.h> #include <asm/assembler.h> -ENTRY(shmobile_init_cntvoff) - /* - * CNTVOFF has to be initialized either from non-secure Hypervisor - * mode or secure Monitor mode with SCR.NS==1. If TrustZone is enabled - * then it should be handled by the secure code - */ - cps #MON_MODE - mrc p15, 0, r1, c1, c1, 0 /* Get Secure Config */ - orr r0, r1, #1 - mcr p15, 0, r0, c1, c1, 0 /* Set Non Secure bit */ - instr_sync - mov r0, #0 - mcrr p15, 4, r0, r0, c14 /* CNTVOFF = 0 */ - instr_sync - mcr p15, 0, r1, c1, c1, 0 /* Set Secure bit */ - instr_sync - cps #SVC_MODE - ret lr -ENDPROC(shmobile_init_cntvoff) - #ifdef CONFIG_SMP ENTRY(shmobile_boot_apmu) - bl shmobile_init_cntvoff + bl secure_cntvoff_init b secondary_startup ENDPROC(shmobile_boot_apmu) #endif diff --git a/arch/arm/mach-shmobile/setup-rcar-gen2.c b/arch/arm/mach-shmobile/setup-rcar-gen2.c index 5561dbed7a33..88fdc1801d90 100644 --- a/arch/arm/mach-shmobile/setup-rcar-gen2.c +++ b/arch/arm/mach-shmobile/setup-rcar-gen2.c @@ -26,6 +26,7 @@ #include <linux/of_fdt.h> #include <linux/of_platform.h> #include <asm/mach/arch.h> +#include <asm/secure_cntvoff.h> #include "common.h" #include "rcar-gen2.h" @@ -70,9 +71,10 @@ void __init rcar_gen2_timer_init(void) void __iomem *base; u32 freq; - shmobile_init_cntvoff(); + secure_cntvoff_init(); if (of_machine_is_compatible("renesas,r8a7745") || + of_machine_is_compatible("renesas,r8a77470") || of_machine_is_compatible("renesas,r8a7792") || of_machine_is_compatible("renesas,r8a7794")) { freq = 260000000 / 8; /* ZS / 8 */ @@ -205,6 +207,7 @@ MACHINE_END static const char * const rz_g1_boards_compat_dt[] __initconst = { "renesas,r8a7743", "renesas,r8a7745", + "renesas,r8a77470", NULL, }; diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig index ce53ceaf4cc5..d9c8ecf88ec6 100644 --- a/arch/arm/mach-sunxi/Kconfig +++ b/arch/arm/mach-sunxi/Kconfig @@ -51,7 +51,7 @@ config MACH_SUN9I config ARCH_SUNXI_MC_SMP bool depends on SMP - default MACH_SUN9I + default MACH_SUN9I || MACH_SUN8I select ARM_CCI400_PORT_CTRL select ARM_CPU_SUSPEND diff --git a/arch/arm/mach-sunxi/Makefile b/arch/arm/mach-sunxi/Makefile index 7de9cc286d53..71429aa85143 100644 --- a/arch/arm/mach-sunxi/Makefile +++ b/arch/arm/mach-sunxi/Makefile @@ -1,5 +1,5 @@ CFLAGS_mc_smp.o += -march=armv7-a obj-$(CONFIG_ARCH_SUNXI) += sunxi.o -obj-$(CONFIG_ARCH_SUNXI_MC_SMP) += mc_smp.o +obj-$(CONFIG_ARCH_SUNXI_MC_SMP) += mc_smp.o headsmp.o obj-$(CONFIG_SMP) += platsmp.o diff --git a/arch/arm/mach-sunxi/headsmp.S b/arch/arm/mach-sunxi/headsmp.S new file mode 100644 index 000000000000..32d76be98541 --- /dev/null +++ b/arch/arm/mach-sunxi/headsmp.S @@ -0,0 +1,81 @@ +/* SPDX-License-Identifier: GPL-2.0 + * + * Copyright (c) 2018 Chen-Yu Tsai + * Copyright (c) 2018 Bootlin + * + * Chen-Yu Tsai <wens@csie.org> + * Mylène Josserand <mylene.josserand@bootlin.com> + * + * SMP support for sunxi based systems with Cortex A7/A15 + * + */ + +#include <linux/linkage.h> +#include <asm/assembler.h> +#include <asm/cputype.h> + +ENTRY(sunxi_mc_smp_cluster_cache_enable) + .arch armv7-a + /* + * Enable cluster-level coherency, in preparation for turning on the MMU. + * + * Also enable regional clock gating and L2 data latency settings for + * Cortex-A15. These settings are from the vendor kernel. + */ + mrc p15, 0, r1, c0, c0, 0 + movw r2, #(ARM_CPU_PART_MASK & 0xffff) + movt r2, #(ARM_CPU_PART_MASK >> 16) + and r1, r1, r2 + movw r2, #(ARM_CPU_PART_CORTEX_A15 & 0xffff) + movt r2, #(ARM_CPU_PART_CORTEX_A15 >> 16) + cmp r1, r2 + bne not_a15 + + /* The following is Cortex-A15 specific */ + + /* ACTLR2: Enable CPU regional clock gates */ + mrc p15, 1, r1, c15, c0, 4 + orr r1, r1, #(0x1 << 31) + mcr p15, 1, r1, c15, c0, 4 + + /* L2ACTLR */ + mrc p15, 1, r1, c15, c0, 0 + /* Enable L2, GIC, and Timer regional clock gates */ + orr r1, r1, #(0x1 << 26) + /* Disable clean/evict from being pushed to external */ + orr r1, r1, #(0x1<<3) + mcr p15, 1, r1, c15, c0, 0 + + /* L2CTRL: L2 data RAM latency */ + mrc p15, 1, r1, c9, c0, 2 + bic r1, r1, #(0x7 << 0) + orr r1, r1, #(0x3 << 0) + mcr p15, 1, r1, c9, c0, 2 + + /* End of Cortex-A15 specific setup */ + not_a15: + + /* Get value of sunxi_mc_smp_first_comer */ + adr r1, first + ldr r0, [r1] + ldr r0, [r1, r0] + + /* Skip cci_enable_port_for_self if not first comer */ + cmp r0, #0 + bxeq lr + b cci_enable_port_for_self + + .align 2 + first: .word sunxi_mc_smp_first_comer - . +ENDPROC(sunxi_mc_smp_cluster_cache_enable) + +ENTRY(sunxi_mc_smp_secondary_startup) + bl sunxi_mc_smp_cluster_cache_enable + bl secure_cntvoff_init + b secondary_startup +ENDPROC(sunxi_mc_smp_secondary_startup) + +ENTRY(sunxi_mc_smp_resume) + bl sunxi_mc_smp_cluster_cache_enable + b cpu_resume +ENDPROC(sunxi_mc_smp_resume) diff --git a/arch/arm/mach-sunxi/mc_smp.c b/arch/arm/mach-sunxi/mc_smp.c index c0246ec54a0a..b4037b603897 100644 --- a/arch/arm/mach-sunxi/mc_smp.c +++ b/arch/arm/mach-sunxi/mc_smp.c @@ -55,22 +55,35 @@ #define CPUCFG_CX_RST_CTRL_L2_RST BIT(8) #define CPUCFG_CX_RST_CTRL_CX_RST(n) BIT(4 + (n)) #define CPUCFG_CX_RST_CTRL_CORE_RST(n) BIT(n) +#define CPUCFG_CX_RST_CTRL_CORE_RST_ALL (0xf << 0) #define PRCM_CPU_PO_RST_CTRL(c) (0x4 + 0x4 * (c)) #define PRCM_CPU_PO_RST_CTRL_CORE(n) BIT(n) #define PRCM_CPU_PO_RST_CTRL_CORE_ALL 0xf #define PRCM_PWROFF_GATING_REG(c) (0x100 + 0x4 * (c)) -#define PRCM_PWROFF_GATING_REG_CLUSTER BIT(4) +/* The power off register for clusters are different from a80 and a83t */ +#define PRCM_PWROFF_GATING_REG_CLUSTER_SUN8I BIT(0) +#define PRCM_PWROFF_GATING_REG_CLUSTER_SUN9I BIT(4) #define PRCM_PWROFF_GATING_REG_CORE(n) BIT(n) #define PRCM_PWR_SWITCH_REG(c, cpu) (0x140 + 0x10 * (c) + 0x4 * (cpu)) #define PRCM_CPU_SOFT_ENTRY_REG 0x164 +/* R_CPUCFG registers, specific to sun8i-a83t */ +#define R_CPUCFG_CLUSTER_PO_RST_CTRL(c) (0x30 + (c) * 0x4) +#define R_CPUCFG_CLUSTER_PO_RST_CTRL_CORE(n) BIT(n) +#define R_CPUCFG_CPU_SOFT_ENTRY_REG 0x01a4 + #define CPU0_SUPPORT_HOTPLUG_MAGIC0 0xFA50392F #define CPU0_SUPPORT_HOTPLUG_MAGIC1 0x790DCA3A static void __iomem *cpucfg_base; static void __iomem *prcm_base; static void __iomem *sram_b_smp_base; +static void __iomem *r_cpucfg_base; + +extern void sunxi_mc_smp_secondary_startup(void); +extern void sunxi_mc_smp_resume(void); +static bool is_a83t; static bool sunxi_core_is_cortex_a15(unsigned int core, unsigned int cluster) { @@ -157,6 +170,16 @@ static int sunxi_cpu_powerup(unsigned int cpu, unsigned int cluster) reg &= ~PRCM_CPU_PO_RST_CTRL_CORE(cpu); writel(reg, prcm_base + PRCM_CPU_PO_RST_CTRL(cluster)); + if (is_a83t) { + /* assert cpu power-on reset */ + reg = readl(r_cpucfg_base + + R_CPUCFG_CLUSTER_PO_RST_CTRL(cluster)); + reg &= ~(R_CPUCFG_CLUSTER_PO_RST_CTRL_CORE(cpu)); + writel(reg, r_cpucfg_base + + R_CPUCFG_CLUSTER_PO_RST_CTRL(cluster)); + udelay(10); + } + /* Cortex-A7: hold L1 reset disable signal low */ if (!sunxi_core_is_cortex_a15(cpu, cluster)) { reg = readl(cpucfg_base + CPUCFG_CX_CTRL_REG0(cluster)); @@ -180,17 +203,38 @@ static int sunxi_cpu_powerup(unsigned int cpu, unsigned int cluster) /* open power switch */ sunxi_cpu_power_switch_set(cpu, cluster, true); + /* Handle A83T bit swap */ + if (is_a83t) { + if (cpu == 0) + cpu = 4; + } + /* clear processor power gate */ reg = readl(prcm_base + PRCM_PWROFF_GATING_REG(cluster)); reg &= ~PRCM_PWROFF_GATING_REG_CORE(cpu); writel(reg, prcm_base + PRCM_PWROFF_GATING_REG(cluster)); udelay(20); + /* Handle A83T bit swap */ + if (is_a83t) { + if (cpu == 4) + cpu = 0; + } + /* de-assert processor power-on reset */ reg = readl(prcm_base + PRCM_CPU_PO_RST_CTRL(cluster)); reg |= PRCM_CPU_PO_RST_CTRL_CORE(cpu); writel(reg, prcm_base + PRCM_CPU_PO_RST_CTRL(cluster)); + if (is_a83t) { + reg = readl(r_cpucfg_base + + R_CPUCFG_CLUSTER_PO_RST_CTRL(cluster)); + reg |= R_CPUCFG_CLUSTER_PO_RST_CTRL_CORE(cpu); + writel(reg, r_cpucfg_base + + R_CPUCFG_CLUSTER_PO_RST_CTRL(cluster)); + udelay(10); + } + /* de-assert all processor resets */ reg = readl(cpucfg_base + CPUCFG_CX_RST_CTRL(cluster)); reg |= CPUCFG_CX_RST_CTRL_DBG_RST(cpu); @@ -212,6 +256,14 @@ static int sunxi_cluster_powerup(unsigned int cluster) if (cluster >= SUNXI_NR_CLUSTERS) return -EINVAL; + /* For A83T, assert cluster cores resets */ + if (is_a83t) { + reg = readl(cpucfg_base + CPUCFG_CX_RST_CTRL(cluster)); + reg &= ~CPUCFG_CX_RST_CTRL_CORE_RST_ALL; /* Core Reset */ + writel(reg, cpucfg_base + CPUCFG_CX_RST_CTRL(cluster)); + udelay(10); + } + /* assert ACINACTM */ reg = readl(cpucfg_base + CPUCFG_CX_CTRL_REG1(cluster)); reg |= CPUCFG_CX_CTRL_REG1_ACINACTM; @@ -222,6 +274,16 @@ static int sunxi_cluster_powerup(unsigned int cluster) reg &= ~PRCM_CPU_PO_RST_CTRL_CORE_ALL; writel(reg, prcm_base + PRCM_CPU_PO_RST_CTRL(cluster)); + /* assert cluster cores resets */ + if (is_a83t) { + reg = readl(r_cpucfg_base + + R_CPUCFG_CLUSTER_PO_RST_CTRL(cluster)); + reg &= ~CPUCFG_CX_RST_CTRL_CORE_RST_ALL; + writel(reg, r_cpucfg_base + + R_CPUCFG_CLUSTER_PO_RST_CTRL(cluster)); + udelay(10); + } + /* assert cluster resets */ reg = readl(cpucfg_base + CPUCFG_CX_RST_CTRL(cluster)); reg &= ~CPUCFG_CX_RST_CTRL_DBG_SOC_RST; @@ -252,7 +314,10 @@ static int sunxi_cluster_powerup(unsigned int cluster) /* clear cluster power gate */ reg = readl(prcm_base + PRCM_PWROFF_GATING_REG(cluster)); - reg &= ~PRCM_PWROFF_GATING_REG_CLUSTER; + if (is_a83t) + reg &= ~PRCM_PWROFF_GATING_REG_CLUSTER_SUN8I; + else + reg &= ~PRCM_PWROFF_GATING_REG_CLUSTER_SUN9I; writel(reg, prcm_base + PRCM_PWROFF_GATING_REG(cluster)); udelay(20); @@ -300,74 +365,7 @@ static void sunxi_cluster_cache_disable_without_axi(void) } static int sunxi_mc_smp_cpu_table[SUNXI_NR_CLUSTERS][SUNXI_CPUS_PER_CLUSTER]; -static int sunxi_mc_smp_first_comer; - -/* - * Enable cluster-level coherency, in preparation for turning on the MMU. - * - * Also enable regional clock gating and L2 data latency settings for - * Cortex-A15. These settings are from the vendor kernel. - */ -static void __naked sunxi_mc_smp_cluster_cache_enable(void) -{ - asm volatile ( - "mrc p15, 0, r1, c0, c0, 0\n" - "movw r2, #" __stringify(ARM_CPU_PART_MASK & 0xffff) "\n" - "movt r2, #" __stringify(ARM_CPU_PART_MASK >> 16) "\n" - "and r1, r1, r2\n" - "movw r2, #" __stringify(ARM_CPU_PART_CORTEX_A15 & 0xffff) "\n" - "movt r2, #" __stringify(ARM_CPU_PART_CORTEX_A15 >> 16) "\n" - "cmp r1, r2\n" - "bne not_a15\n" - - /* The following is Cortex-A15 specific */ - - /* ACTLR2: Enable CPU regional clock gates */ - "mrc p15, 1, r1, c15, c0, 4\n" - "orr r1, r1, #(0x1<<31)\n" - "mcr p15, 1, r1, c15, c0, 4\n" - - /* L2ACTLR */ - "mrc p15, 1, r1, c15, c0, 0\n" - /* Enable L2, GIC, and Timer regional clock gates */ - "orr r1, r1, #(0x1<<26)\n" - /* Disable clean/evict from being pushed to external */ - "orr r1, r1, #(0x1<<3)\n" - "mcr p15, 1, r1, c15, c0, 0\n" - - /* L2CTRL: L2 data RAM latency */ - "mrc p15, 1, r1, c9, c0, 2\n" - "bic r1, r1, #(0x7<<0)\n" - "orr r1, r1, #(0x3<<0)\n" - "mcr p15, 1, r1, c9, c0, 2\n" - - /* End of Cortex-A15 specific setup */ - "not_a15:\n" - - /* Get value of sunxi_mc_smp_first_comer */ - "adr r1, first\n" - "ldr r0, [r1]\n" - "ldr r0, [r1, r0]\n" - - /* Skip cci_enable_port_for_self if not first comer */ - "cmp r0, #0\n" - "bxeq lr\n" - "b cci_enable_port_for_self\n" - - ".align 2\n" - "first: .word sunxi_mc_smp_first_comer - .\n" - ); -} - -static void __naked sunxi_mc_smp_secondary_startup(void) -{ - asm volatile( - "bl sunxi_mc_smp_cluster_cache_enable\n" - "b secondary_startup" - /* Let compiler know about sunxi_mc_smp_cluster_cache_enable */ - :: "i" (sunxi_mc_smp_cluster_cache_enable) - ); -} +int sunxi_mc_smp_first_comer; static DEFINE_SPINLOCK(boot_lock); @@ -516,7 +514,10 @@ static int sunxi_cluster_powerdown(unsigned int cluster) /* gate cluster power */ pr_debug("%s: gate cluster power\n", __func__); reg = readl(prcm_base + PRCM_PWROFF_GATING_REG(cluster)); - reg |= PRCM_PWROFF_GATING_REG_CLUSTER; + if (is_a83t) + reg |= PRCM_PWROFF_GATING_REG_CLUSTER_SUN8I; + else + reg |= PRCM_PWROFF_GATING_REG_CLUSTER_SUN9I; writel(reg, prcm_base + PRCM_PWROFF_GATING_REG(cluster)); udelay(20); @@ -598,8 +599,12 @@ out: return !ret; } -static bool sunxi_mc_smp_cpu_can_disable(unsigned int __unused) +static bool sunxi_mc_smp_cpu_can_disable(unsigned int cpu) { + /* CPU0 hotplug not handled for sun8i-a83t */ + if (is_a83t) + if (cpu == 0) + return false; return true; } #endif @@ -637,16 +642,6 @@ static bool __init sunxi_mc_smp_cpu_table_init(void) */ typedef typeof(cpu_reset) phys_reset_t; -static void __init __naked sunxi_mc_smp_resume(void) -{ - asm volatile( - "bl sunxi_mc_smp_cluster_cache_enable\n" - "b cpu_resume" - /* Let compiler know about sunxi_mc_smp_cluster_cache_enable */ - :: "i" (sunxi_mc_smp_cluster_cache_enable) - ); -} - static int __init nocache_trampoline(unsigned long __unused) { phys_reset_t phys_reset; @@ -692,12 +687,14 @@ struct sunxi_mc_smp_nodes { struct device_node *prcm_node; struct device_node *cpucfg_node; struct device_node *sram_node; + struct device_node *r_cpucfg_node; }; /* This structure holds SoC-specific bits tied to an enable-method string. */ struct sunxi_mc_smp_data { const char *enable_method; int (*get_smp_nodes)(struct sunxi_mc_smp_nodes *nodes); + bool is_a83t; }; static void __init sunxi_mc_smp_put_nodes(struct sunxi_mc_smp_nodes *nodes) @@ -705,6 +702,7 @@ static void __init sunxi_mc_smp_put_nodes(struct sunxi_mc_smp_nodes *nodes) of_node_put(nodes->prcm_node); of_node_put(nodes->cpucfg_node); of_node_put(nodes->sram_node); + of_node_put(nodes->r_cpucfg_node); memset(nodes, 0, sizeof(*nodes)); } @@ -734,11 +732,42 @@ static int __init sun9i_a80_get_smp_nodes(struct sunxi_mc_smp_nodes *nodes) return 0; } +static int __init sun8i_a83t_get_smp_nodes(struct sunxi_mc_smp_nodes *nodes) +{ + nodes->prcm_node = of_find_compatible_node(NULL, NULL, + "allwinner,sun8i-a83t-r-ccu"); + if (!nodes->prcm_node) { + pr_err("%s: PRCM not available\n", __func__); + return -ENODEV; + } + + nodes->cpucfg_node = of_find_compatible_node(NULL, NULL, + "allwinner,sun8i-a83t-cpucfg"); + if (!nodes->cpucfg_node) { + pr_err("%s: CPUCFG not available\n", __func__); + return -ENODEV; + } + + nodes->r_cpucfg_node = of_find_compatible_node(NULL, NULL, + "allwinner,sun8i-a83t-r-cpucfg"); + if (!nodes->r_cpucfg_node) { + pr_err("%s: RCPUCFG not available\n", __func__); + return -ENODEV; + } + + return 0; +} + static const struct sunxi_mc_smp_data sunxi_mc_smp_data[] __initconst = { { .enable_method = "allwinner,sun9i-a80-smp", .get_smp_nodes = sun9i_a80_get_smp_nodes, }, + { + .enable_method = "allwinner,sun8i-a83t-smp", + .get_smp_nodes = sun8i_a83t_get_smp_nodes, + .is_a83t = true, + }, }; static int __init sunxi_mc_smp_init(void) @@ -746,6 +775,7 @@ static int __init sunxi_mc_smp_init(void) struct sunxi_mc_smp_nodes nodes = { 0 }; struct device_node *node; struct resource res; + void __iomem *addr; int i, ret; /* @@ -771,6 +801,8 @@ static int __init sunxi_mc_smp_init(void) break; } + is_a83t = sunxi_mc_smp_data[i].is_a83t; + of_node_put(node); if (ret) return -ENODEV; @@ -808,12 +840,23 @@ static int __init sunxi_mc_smp_init(void) goto err_unmap_prcm; } - sram_b_smp_base = of_io_request_and_map(nodes.sram_node, 0, - "sunxi-mc-smp"); - if (IS_ERR(sram_b_smp_base)) { - ret = PTR_ERR(sram_b_smp_base); - pr_err("%s: failed to map secure SRAM\n", __func__); - goto err_unmap_release_cpucfg; + if (is_a83t) { + r_cpucfg_base = of_io_request_and_map(nodes.r_cpucfg_node, + 0, "sunxi-mc-smp"); + if (IS_ERR(r_cpucfg_base)) { + ret = PTR_ERR(r_cpucfg_base); + pr_err("%s: failed to map R-CPUCFG registers\n", + __func__); + goto err_unmap_release_cpucfg; + } + } else { + sram_b_smp_base = of_io_request_and_map(nodes.sram_node, 0, + "sunxi-mc-smp"); + if (IS_ERR(sram_b_smp_base)) { + ret = PTR_ERR(sram_b_smp_base); + pr_err("%s: failed to map secure SRAM\n", __func__); + goto err_unmap_release_cpucfg; + } } /* Configure CCI-400 for boot cluster */ @@ -821,15 +864,18 @@ static int __init sunxi_mc_smp_init(void) if (ret) { pr_err("%s: failed to configure boot cluster: %d\n", __func__, ret); - goto err_unmap_release_secure_sram; + goto err_unmap_release_sram_rcpucfg; } /* We don't need the device nodes anymore */ sunxi_mc_smp_put_nodes(&nodes); /* Set the hardware entry point address */ - writel(__pa_symbol(sunxi_mc_smp_secondary_startup), - prcm_base + PRCM_CPU_SOFT_ENTRY_REG); + if (is_a83t) + addr = r_cpucfg_base + R_CPUCFG_CPU_SOFT_ENTRY_REG; + else + addr = prcm_base + PRCM_CPU_SOFT_ENTRY_REG; + writel(__pa_symbol(sunxi_mc_smp_secondary_startup), addr); /* Actually enable multi cluster SMP */ smp_set_ops(&sunxi_mc_smp_smp_ops); @@ -838,9 +884,14 @@ static int __init sunxi_mc_smp_init(void) return 0; -err_unmap_release_secure_sram: - iounmap(sram_b_smp_base); - of_address_to_resource(nodes.sram_node, 0, &res); +err_unmap_release_sram_rcpucfg: + if (is_a83t) { + iounmap(r_cpucfg_base); + of_address_to_resource(nodes.r_cpucfg_node, 0, &res); + } else { + iounmap(sram_b_smp_base); + of_address_to_resource(nodes.sram_node, 0, &res); + } release_mem_region(res.start, resource_size(&res)); err_unmap_release_cpucfg: iounmap(cpucfg_base); diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c index 5e9602ce1573..de4b0e932f22 100644 --- a/arch/arm/mach-sunxi/sunxi.c +++ b/arch/arm/mach-sunxi/sunxi.c @@ -16,6 +16,7 @@ #include <linux/platform_device.h> #include <asm/mach/arch.h> +#include <asm/secure_cntvoff.h> static const char * const sunxi_board_dt_compat[] = { "allwinner,sun4i-a10", @@ -62,7 +63,6 @@ MACHINE_END static const char * const sun8i_board_dt_compat[] = { "allwinner,sun8i-a23", "allwinner,sun8i-a33", - "allwinner,sun8i-a83t", "allwinner,sun8i-h2-plus", "allwinner,sun8i-h3", "allwinner,sun8i-r40", @@ -75,6 +75,24 @@ DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i Family") .dt_compat = sun8i_board_dt_compat, MACHINE_END +static void __init sun8i_a83t_cntvoff_init(void) +{ +#ifdef CONFIG_SMP + secure_cntvoff_init(); +#endif +} + +static const char * const sun8i_a83t_cntvoff_board_dt_compat[] = { + "allwinner,sun8i-a83t", + NULL, +}; + +DT_MACHINE_START(SUN8I_A83T_CNTVOFF_DT, "Allwinner A83t board") + .init_early = sun8i_a83t_cntvoff_init, + .init_time = sun6i_timer_init, + .dt_compat = sun8i_a83t_cntvoff_board_dt_compat, +MACHINE_END + static const char * const sun9i_board_dt_compat[] = { "allwinner,sun9i-a80", NULL, diff --git a/arch/arm/mach-tegra/Kconfig b/arch/arm/mach-tegra/Kconfig index 1e0aeb47bac6..7f3b83e0d324 100644 --- a/arch/arm/mach-tegra/Kconfig +++ b/arch/arm/mach-tegra/Kconfig @@ -15,6 +15,5 @@ menuconfig ARCH_TEGRA select RESET_CONTROLLER select SOC_BUS select ZONE_DMA if ARM_LPAE - select ARCH_DMA_ADDR_T_64BIT if ARM_LPAE help This enables support for NVIDIA Tegra based systems. diff --git a/arch/arm/mach-tegra/tegra.c b/arch/arm/mach-tegra/tegra.c index 02e712d2ea30..f9587be48235 100644 --- a/arch/arm/mach-tegra/tegra.c +++ b/arch/arm/mach-tegra/tegra.c @@ -97,6 +97,10 @@ static void __init tegra_dt_init_late(void) if (IS_ENABLED(CONFIG_ARCH_TEGRA_2x_SOC) && of_machine_is_compatible("compal,paz00")) tegra_paz00_wifikill_init(); + + if (IS_ENABLED(CONFIG_ARCH_TEGRA_2x_SOC) && + of_machine_is_compatible("nvidia,tegra20")) + platform_device_register_simple("tegra20-cpufreq", -1, NULL, 0); } static const char * const tegra_dt_board_compat[] = { diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig index f98332ea2ef2..c1086ebe0050 100644 --- a/arch/arm/mach-ux500/Kconfig +++ b/arch/arm/mach-ux500/Kconfig @@ -9,64 +9,33 @@ menuconfig ARCH_U8500 select ARM_ERRATA_764369 if SMP select ARM_GIC select CACHE_L2X0 + select CLKSRC_DBX500_PRCMU select CLKSRC_NOMADIK_MTU select GPIOLIB select HAVE_ARM_SCU if SMP select HAVE_ARM_TWD if SMP + select I2C + select I2C_NOMADIK + select MFD_DB8500_PRCMU select PINCTRL + select PINCTRL_AB8500 + select PINCTRL_AB8505 select PINCTRL_ABX500 + select PINCTRL_DB8500 select PINCTRL_NOMADIK select PL310_ERRATA_753970 if CACHE_L2X0 - help - Support for ST-Ericsson's Ux500 architecture - -if ARCH_U8500 - -config UX500_SOC_DB8500 - bool - select MFD_DB8500_PRCMU - select PINCTRL_DB8500 - select PINCTRL_DB8540 - select PINCTRL_AB8500 - select PINCTRL_AB8505 - select PINCTRL_AB9540 - select PINCTRL_AB8540 - select REGULATOR - select REGULATOR_DB8500_PRCMU - select CLKSRC_DBX500_PRCMU select PM_GENERIC_DOMAINS if PM - -config MACH_MOP500 - bool "U8500 Development platform, MOP500 versions" - select I2C - select I2C_NOMADIK select REGULATOR + select REGULATOR_DB8500_PRCMU select REGULATOR_FIXED_VOLTAGE select SOC_BUS - select UX500_SOC_DB8500 help - Include support for the MOP500 development platform. - -config MACH_HREFV60 - bool "U8500 Development platform, HREFv60 version" - select MACH_MOP500 - help - Include support for the HREFv60 new development platform. - Includes HREFv70, v71 etc. + Support for ST-Ericsson's Ux500 architecture -config MACH_SNOWBALL - bool "U8500 Snowball platform" - select MACH_MOP500 - help - Include support for the snowball development platform. +if ARCH_U8500 -config UX500_AUTO_PLATFORM +config UX500_SOC_DB8500 def_bool y - select MACH_MOP500 - help - At least one platform needs to be selected in order to build - a working kernel. If everything else is disabled, this - automatically enables MACH_MOP500. config UX500_DEBUG_UART int "Ux500 UART to use for low-level debug" diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c index 36cd23c8be9b..389ecf6faa00 100644 --- a/arch/arm/mach-ux500/cpu-db8500.c +++ b/arch/arm/mach-ux500/cpu-db8500.c @@ -111,11 +111,6 @@ static void ux500_restart(enum reboot_mode mode, const char *cmd) prcmu_system_reset(0); } -static struct of_dev_auxdata u8540_auxdata_lookup[] __initdata = { - OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu", NULL), - {}, -}; - static const struct of_device_id u8500_local_bus_nodes[] = { /* only create devices below soc node */ { .compatible = "stericsson,db8500", }, @@ -129,20 +124,13 @@ static void __init u8500_init_machine(void) /* Initialize ux500 power domains */ ux500_pm_domains_init(); - /* automatically probe child nodes of dbx5x0 devices */ - if (of_machine_is_compatible("st-ericsson,u8540")) - of_platform_populate(NULL, u8500_local_bus_nodes, - u8540_auxdata_lookup, NULL); - else - of_platform_populate(NULL, u8500_local_bus_nodes, - NULL, NULL); + of_platform_populate(NULL, u8500_local_bus_nodes, + NULL, NULL); } static const char * stericsson_dt_platform_compat[] = { "st-ericsson,u8500", - "st-ericsson,u8540", "st-ericsson,u9500", - "st-ericsson,u9540", NULL, }; diff --git a/arch/arm/mach-ux500/db8500-regs.h b/arch/arm/mach-ux500/db8500-regs.h index 27399553c841..3d6e1955119a 100644 --- a/arch/arm/mach-ux500/db8500-regs.h +++ b/arch/arm/mach-ux500/db8500-regs.h @@ -41,10 +41,6 @@ /* ASIC ID is at 0xbf4 offset within this region */ #define U8500_ASIC_ID_BASE 0x9001D000 -#define U9540_BOOT_ROM_BASE 0xFFFE0000 -/* ASIC ID is at 0xbf4 offset within this region */ -#define U9540_ASIC_ID_BASE 0xFFFFD000 - #define U8500_PER6_BASE 0xa03c0000 #define U8500_PER7_BASE 0xa03d0000 #define U8500_PER5_BASE 0xa03e0000 diff --git a/arch/arm/mach-vexpress/spc.c b/arch/arm/mach-vexpress/spc.c index 21c064267af5..0f5381d13494 100644 --- a/arch/arm/mach-vexpress/spc.c +++ b/arch/arm/mach-vexpress/spc.c @@ -403,7 +403,7 @@ static int ve_spc_populate_opps(uint32_t cluster) uint32_t data = 0, off, ret, idx; struct ve_spc_opp *opps; - opps = kzalloc(sizeof(*opps) * MAX_OPPS, GFP_KERNEL); + opps = kcalloc(MAX_OPPS, sizeof(*opps), GFP_KERNEL); if (!opps) return -ENOMEM; diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index 7f14acf67caf..96a7b6cf459b 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -415,6 +415,7 @@ config CPU_V7 select CPU_CP15_MPU if !MMU select CPU_HAS_ASID if MMU select CPU_PABRT_V7 + select CPU_SPECTRE if MMU select CPU_THUMB_CAPABLE select CPU_TLB_V7 if MMU @@ -661,6 +662,7 @@ config ARM_LPAE bool "Support for the Large Physical Address Extension" depends on MMU && CPU_32v7 && !CPU_32v6 && !CPU_32v5 && \ !CPU_32v4 && !CPU_32v3 + select PHYS_ADDR_T_64BIT help Say Y if you have an ARMv7 processor supporting the LPAE page table format and you would like to access memory beyond the @@ -673,12 +675,6 @@ config ARM_PV_FIXUP def_bool y depends on ARM_LPAE && ARM_PATCH_PHYS_VIRT && ARCH_KEYSTONE -config ARCH_PHYS_ADDR_T_64BIT - def_bool ARM_LPAE - -config ARCH_DMA_ADDR_T_64BIT - bool - config ARM_THUMB bool "Support Thumb user binaries" if !CPU_THUMBONLY && EXPERT depends on CPU_THUMB_CAPABLE @@ -826,6 +822,28 @@ config CPU_BPREDICT_DISABLE help Say Y here to disable branch prediction. If unsure, say N. +config CPU_SPECTRE + bool + +config HARDEN_BRANCH_PREDICTOR + bool "Harden the branch predictor against aliasing attacks" if EXPERT + depends on CPU_SPECTRE + default y + help + Speculation attacks against some high-performance processors rely + on being able to manipulate the branch predictor for a victim + context by executing aliasing branches in the attacker context. + Such attacks can be partially mitigated against by clearing + internal branch predictor state and limiting the prediction + logic in some situations. + + This config option will take CPU-specific actions to harden + the branch predictor against aliasing attacks and may rely on + specific instruction sequences or control bits being set by + the system firmware. + + If unsure, say Y. + config TLS_REG_EMUL bool select NEED_KUSER_HELPERS diff --git a/arch/arm/mm/Makefile b/arch/arm/mm/Makefile index 9dbb84923e12..7cb1699fbfc4 100644 --- a/arch/arm/mm/Makefile +++ b/arch/arm/mm/Makefile @@ -10,7 +10,7 @@ obj-$(CONFIG_MMU) += fault-armv.o flush.o idmap.o ioremap.o \ ifneq ($(CONFIG_MMU),y) obj-y += nommu.o -obj-$(CONFIG_ARM_MPU) += pmsa-v7.o +obj-$(CONFIG_ARM_MPU) += pmsa-v7.o pmsa-v8.o endif obj-$(CONFIG_ARM_PTDUMP_CORE) += dump.o @@ -97,7 +97,7 @@ obj-$(CONFIG_CPU_MOHAWK) += proc-mohawk.o obj-$(CONFIG_CPU_FEROCEON) += proc-feroceon.o obj-$(CONFIG_CPU_V6) += proc-v6.o obj-$(CONFIG_CPU_V6K) += proc-v6.o -obj-$(CONFIG_CPU_V7) += proc-v7.o +obj-$(CONFIG_CPU_V7) += proc-v7.o proc-v7-bugs.o obj-$(CONFIG_CPU_V7M) += proc-v7m.o AFLAGS_proc-v6.o :=-Wa,-march=armv6 diff --git a/arch/arm/mm/alignment.c b/arch/arm/mm/alignment.c index 2c96190e018b..bd2c739d8083 100644 --- a/arch/arm/mm/alignment.c +++ b/arch/arm/mm/alignment.c @@ -950,6 +950,7 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs) if (ai_usermode & UM_SIGNAL) { siginfo_t si; + clear_siginfo(&si); si.si_signo = SIGBUS; si.si_errno = 0; si.si_code = BUS_ADRALN; diff --git a/arch/arm/mm/cache-b15-rac.c b/arch/arm/mm/cache-b15-rac.c index d9586ba2e63c..c6ed14840c3c 100644 --- a/arch/arm/mm/cache-b15-rac.c +++ b/arch/arm/mm/cache-b15-rac.c @@ -33,7 +33,10 @@ extern void v7_flush_kern_cache_all(void); #define RAC_CPU_SHIFT (8) #define RACCFG_MASK (0xff) #define RAC_CONFIG1_REG (0x7c) -#define RAC_FLUSH_REG (0x80) +/* Brahma-B15 is a quad-core only design */ +#define B15_RAC_FLUSH_REG (0x80) +/* Brahma-B53 is an octo-core design */ +#define B53_RAC_FLUSH_REG (0x84) #define FLUSH_RAC (1 << 0) /* Bitmask to enable instruction and data prefetching with a 256-bytes stride */ @@ -52,6 +55,7 @@ static void __iomem *b15_rac_base; static DEFINE_SPINLOCK(rac_lock); static u32 rac_config0_reg; +static u32 rac_flush_offset; /* Initialization flag to avoid checking for b15_rac_base, and to prevent * multi-platform kernels from crashing here as well. @@ -70,14 +74,14 @@ static inline void __b15_rac_flush(void) { u32 reg; - __raw_writel(FLUSH_RAC, b15_rac_base + RAC_FLUSH_REG); + __raw_writel(FLUSH_RAC, b15_rac_base + rac_flush_offset); do { /* This dmb() is required to force the Bus Interface Unit * to clean oustanding writes, and forces an idle cycle * to be inserted. */ dmb(); - reg = __raw_readl(b15_rac_base + RAC_FLUSH_REG); + reg = __raw_readl(b15_rac_base + rac_flush_offset); } while (reg & FLUSH_RAC); } @@ -287,7 +291,7 @@ static struct syscore_ops b15_rac_syscore_ops = { static int __init b15_rac_init(void) { - struct device_node *dn; + struct device_node *dn, *cpu_dn; int ret = 0, cpu; u32 reg, en_mask = 0; @@ -305,6 +309,24 @@ static int __init b15_rac_init(void) goto out; } + cpu_dn = of_get_cpu_node(0, NULL); + if (!cpu_dn) { + ret = -ENODEV; + goto out; + } + + if (of_device_is_compatible(cpu_dn, "brcm,brahma-b15")) + rac_flush_offset = B15_RAC_FLUSH_REG; + else if (of_device_is_compatible(cpu_dn, "brcm,brahma-b53")) + rac_flush_offset = B53_RAC_FLUSH_REG; + else { + pr_err("Unsupported CPU\n"); + of_node_put(cpu_dn); + ret = -EINVAL; + goto out; + } + of_node_put(cpu_dn); + ret = register_reboot_notifier(&b15_rac_reboot_nb); if (ret) { pr_err("failed to register reboot notifier\n"); diff --git a/arch/arm/mm/dma-mapping-nommu.c b/arch/arm/mm/dma-mapping-nommu.c index 619f24a42d09..f448a0663b10 100644 --- a/arch/arm/mm/dma-mapping-nommu.c +++ b/arch/arm/mm/dma-mapping-nommu.c @@ -241,12 +241,3 @@ void arch_setup_dma_ops(struct device *dev, u64 dma_base, u64 size, void arch_teardown_dma_ops(struct device *dev) { } - -#define PREALLOC_DMA_DEBUG_ENTRIES 4096 - -static int __init dma_debug_do_init(void) -{ - dma_debug_init(PREALLOC_DMA_DEBUG_ENTRIES); - return 0; -} -core_initcall(dma_debug_do_init); diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c index 8c398fedbbb6..be0fa7e39c26 100644 --- a/arch/arm/mm/dma-mapping.c +++ b/arch/arm/mm/dma-mapping.c @@ -466,12 +466,6 @@ void __init dma_contiguous_early_fixup(phys_addr_t base, unsigned long size) void __init dma_contiguous_remap(void) { int i; - - if (!dma_mmu_remap_num) - return; - - /* call flush_cache_all() since CMA area would be large enough */ - flush_cache_all(); for (i = 0; i < dma_mmu_remap_num; i++) { phys_addr_t start = dma_mmu_remap[i].base; phys_addr_t end = start + dma_mmu_remap[i].size; @@ -504,15 +498,7 @@ void __init dma_contiguous_remap(void) flush_tlb_kernel_range(__phys_to_virt(start), __phys_to_virt(end)); - /* - * All the memory in CMA region will be on ZONE_MOVABLE. - * If that zone is considered as highmem, the memory in CMA - * region is also considered as highmem even if it's - * physical address belong to lowmem. In this case, - * re-mapping isn't required. - */ - if (!is_highmem_idx(ZONE_MOVABLE)) - iotable_init(&map, 1); + iotable_init(&map, 1); } } @@ -845,7 +831,7 @@ static int __arm_dma_mmap(struct device *dev, struct vm_area_struct *vma, unsigned long attrs) { int ret; - unsigned long nr_vma_pages = (vma->vm_end - vma->vm_start) >> PAGE_SHIFT; + unsigned long nr_vma_pages = vma_pages(vma); unsigned long nr_pages = PAGE_ALIGN(size) >> PAGE_SHIFT; unsigned long pfn = dma_to_pfn(dev, dma_addr); unsigned long off = vma->vm_pgoff; @@ -1165,15 +1151,6 @@ int arm_dma_supported(struct device *dev, u64 mask) return __dma_supported(dev, mask, false); } -#define PREALLOC_DMA_DEBUG_ENTRIES 4096 - -static int __init dma_debug_do_init(void) -{ - dma_debug_init(PREALLOC_DMA_DEBUG_ENTRIES); - return 0; -} -core_initcall(dma_debug_do_init); - #ifdef CONFIG_ARM_DMA_USE_IOMMU static int __dma_info_to_prot(enum dma_data_direction dir, unsigned long attrs) @@ -2185,8 +2162,8 @@ arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, u64 size) goto err; mapping->bitmap_size = bitmap_size; - mapping->bitmaps = kzalloc(extensions * sizeof(unsigned long *), - GFP_KERNEL); + mapping->bitmaps = kcalloc(extensions, sizeof(unsigned long *), + GFP_KERNEL); if (!mapping->bitmaps) goto err2; diff --git a/arch/arm/mm/fault.c b/arch/arm/mm/fault.c index b75eada23d0a..84becc911ee3 100644 --- a/arch/arm/mm/fault.c +++ b/arch/arm/mm/fault.c @@ -163,6 +163,11 @@ __do_user_fault(struct task_struct *tsk, unsigned long addr, { struct siginfo si; + if (addr > TASK_SIZE) + harden_branch_predictor(); + + clear_siginfo(&si); + #ifdef CONFIG_DEBUG_USER if (((user_debug & UDBG_SEGV) && (sig == SIGSEGV)) || ((user_debug & UDBG_BUS) && (sig == SIGBUS))) { @@ -557,6 +562,7 @@ do_DataAbort(unsigned long addr, unsigned int fsr, struct pt_regs *regs) inf->name, fsr, addr); show_pte(current->mm, addr); + clear_siginfo(&info); info.si_signo = inf->sig; info.si_errno = 0; info.si_code = inf->code; @@ -589,6 +595,7 @@ do_PrefetchAbort(unsigned long addr, unsigned int ifsr, struct pt_regs *regs) pr_alert("Unhandled prefetch abort: %s (0x%03x) at 0x%08lx\n", inf->name, ifsr, addr); + clear_siginfo(&info); info.si_signo = inf->sig; info.si_errno = 0; info.si_code = inf->code; diff --git a/arch/arm/mm/nommu.c b/arch/arm/mm/nommu.c index 7c087961b7ce..5dd6c58d653b 100644 --- a/arch/arm/mm/nommu.c +++ b/arch/arm/mm/nommu.c @@ -99,6 +99,38 @@ void __init arm_mm_memblock_reserve(void) memblock_reserve(0, 1); } +static void __init adjust_lowmem_bounds_mpu(void) +{ + unsigned long pmsa = read_cpuid_ext(CPUID_EXT_MMFR0) & MMFR0_PMSA; + + switch (pmsa) { + case MMFR0_PMSAv7: + pmsav7_adjust_lowmem_bounds(); + break; + case MMFR0_PMSAv8: + pmsav8_adjust_lowmem_bounds(); + break; + default: + break; + } +} + +static void __init mpu_setup(void) +{ + unsigned long pmsa = read_cpuid_ext(CPUID_EXT_MMFR0) & MMFR0_PMSA; + + switch (pmsa) { + case MMFR0_PMSAv7: + pmsav7_setup(); + break; + case MMFR0_PMSAv8: + pmsav8_setup(); + break; + default: + break; + } +} + void __init adjust_lowmem_bounds(void) { phys_addr_t end; diff --git a/arch/arm/mm/pgd.c b/arch/arm/mm/pgd.c index 61e281cb29fb..a1606d950251 100644 --- a/arch/arm/mm/pgd.c +++ b/arch/arm/mm/pgd.c @@ -20,7 +20,7 @@ #include "mm.h" #ifdef CONFIG_ARM_LPAE -#define __pgd_alloc() kmalloc(PTRS_PER_PGD * sizeof(pgd_t), GFP_KERNEL) +#define __pgd_alloc() kmalloc_array(PTRS_PER_PGD, sizeof(pgd_t), GFP_KERNEL) #define __pgd_free(pgd) kfree(pgd) #else #define __pgd_alloc() (pgd_t *)__get_free_pages(GFP_KERNEL, 2) diff --git a/arch/arm/mm/pmsa-v7.c b/arch/arm/mm/pmsa-v7.c index e2853bfff74e..699fa2e88725 100644 --- a/arch/arm/mm/pmsa-v7.c +++ b/arch/arm/mm/pmsa-v7.c @@ -102,7 +102,7 @@ static inline u32 irbar_read(void) static inline void rgnr_write(u32 v) { - writel_relaxed(v, BASEADDR_V7M_SCB + MPU_RNR); + writel_relaxed(v, BASEADDR_V7M_SCB + PMSAv7_RNR); } /* Data-side / unified region attributes */ @@ -110,28 +110,28 @@ static inline void rgnr_write(u32 v) /* Region access control register */ static inline void dracr_write(u32 v) { - u32 rsr = readl_relaxed(BASEADDR_V7M_SCB + MPU_RASR) & GENMASK(15, 0); + u32 rsr = readl_relaxed(BASEADDR_V7M_SCB + PMSAv7_RASR) & GENMASK(15, 0); - writel_relaxed((v << 16) | rsr, BASEADDR_V7M_SCB + MPU_RASR); + writel_relaxed((v << 16) | rsr, BASEADDR_V7M_SCB + PMSAv7_RASR); } /* Region size register */ static inline void drsr_write(u32 v) { - u32 racr = readl_relaxed(BASEADDR_V7M_SCB + MPU_RASR) & GENMASK(31, 16); + u32 racr = readl_relaxed(BASEADDR_V7M_SCB + PMSAv7_RASR) & GENMASK(31, 16); - writel_relaxed(v | racr, BASEADDR_V7M_SCB + MPU_RASR); + writel_relaxed(v | racr, BASEADDR_V7M_SCB + PMSAv7_RASR); } /* Region base address register */ static inline void drbar_write(u32 v) { - writel_relaxed(v, BASEADDR_V7M_SCB + MPU_RBAR); + writel_relaxed(v, BASEADDR_V7M_SCB + PMSAv7_RBAR); } static inline u32 drbar_read(void) { - return readl_relaxed(BASEADDR_V7M_SCB + MPU_RBAR); + return readl_relaxed(BASEADDR_V7M_SCB + PMSAv7_RBAR); } /* ARMv7-M only supports a unified MPU, so I-side operations are nop */ @@ -143,11 +143,6 @@ static inline unsigned long irbar_read(void) {return 0;} #endif -static int __init mpu_present(void) -{ - return ((read_cpuid_ext(CPUID_EXT_MMFR0) & MMFR0_PMSA) == MMFR0_PMSAv7); -} - static bool __init try_split_region(phys_addr_t base, phys_addr_t size, struct region *region) { unsigned long subreg, bslots, sslots; @@ -161,7 +156,7 @@ static bool __init try_split_region(phys_addr_t base, phys_addr_t size, struct r bdiff = base - abase; sdiff = p2size - asize; - subreg = p2size / MPU_NR_SUBREGS; + subreg = p2size / PMSAv7_NR_SUBREGS; if ((bdiff % subreg) || (sdiff % subreg)) return false; @@ -172,17 +167,17 @@ static bool __init try_split_region(phys_addr_t base, phys_addr_t size, struct r if (bslots || sslots) { int i; - if (subreg < MPU_MIN_SUBREG_SIZE) + if (subreg < PMSAv7_MIN_SUBREG_SIZE) return false; - if (bslots + sslots > MPU_NR_SUBREGS) + if (bslots + sslots > PMSAv7_NR_SUBREGS) return false; for (i = 0; i < bslots; i++) _set_bit(i, ®ion->subreg); for (i = 1; i <= sslots; i++) - _set_bit(MPU_NR_SUBREGS - i, ®ion->subreg); + _set_bit(PMSAv7_NR_SUBREGS - i, ®ion->subreg); } region->base = abase; @@ -233,7 +228,7 @@ static int __init allocate_region(phys_addr_t base, phys_addr_t size, } /* MPU initialisation functions */ -void __init adjust_lowmem_bounds_mpu(void) +void __init pmsav7_adjust_lowmem_bounds(void) { phys_addr_t specified_mem_size = 0, total_mem_size = 0; struct memblock_region *reg; @@ -243,10 +238,7 @@ void __init adjust_lowmem_bounds_mpu(void) unsigned int mem_max_regions; int num, i; - if (!mpu_present()) - return; - - /* Free-up MPU_PROBE_REGION */ + /* Free-up PMSAv7_PROBE_REGION */ mpu_min_region_order = __mpu_min_region_order(); /* How many regions are supported */ @@ -301,12 +293,12 @@ void __init adjust_lowmem_bounds_mpu(void) num = allocate_region(mem_start, specified_mem_size, mem_max_regions, mem); for (i = 0; i < num; i++) { - unsigned long subreg = mem[i].size / MPU_NR_SUBREGS; + unsigned long subreg = mem[i].size / PMSAv7_NR_SUBREGS; total_mem_size += mem[i].size - subreg * hweight_long(mem[i].subreg); pr_debug("MPU: base %pa size %pa disable subregions: %*pbl\n", - &mem[i].base, &mem[i].size, MPU_NR_SUBREGS, &mem[i].subreg); + &mem[i].base, &mem[i].size, PMSAv7_NR_SUBREGS, &mem[i].subreg); } if (total_mem_size != specified_mem_size) { @@ -349,7 +341,7 @@ static int __init __mpu_min_region_order(void) u32 drbar_result, irbar_result; /* We've kept a region free for this probing */ - rgnr_write(MPU_PROBE_REGION); + rgnr_write(PMSAv7_PROBE_REGION); isb(); /* * As per ARM ARM, write 0xFFFFFFFC to DRBAR to find the minimum @@ -388,8 +380,8 @@ static int __init mpu_setup_region(unsigned int number, phys_addr_t start, return -ENOMEM; /* Writing N to bits 5:1 (RSR_SZ) specifies region size 2^N+1 */ - size_data = ((size_order - 1) << MPU_RSR_SZ) | 1 << MPU_RSR_EN; - size_data |= subregions << MPU_RSR_SD; + size_data = ((size_order - 1) << PMSAv7_RSR_SZ) | 1 << PMSAv7_RSR_EN; + size_data |= subregions << PMSAv7_RSR_SD; if (need_flush) flush_cache_all(); @@ -424,18 +416,15 @@ static int __init mpu_setup_region(unsigned int number, phys_addr_t start, /* * Set up default MPU regions, doing nothing if there is no MPU */ -void __init mpu_setup(void) +void __init pmsav7_setup(void) { int i, region = 0, err = 0; - if (!mpu_present()) - return; - /* Setup MPU (order is important) */ /* Background */ err |= mpu_setup_region(region++, 0, 32, - MPU_ACR_XN | MPU_RGN_STRONGLY_ORDERED | MPU_AP_PL1RW_PL0RW, + PMSAv7_ACR_XN | PMSAv7_RGN_STRONGLY_ORDERED | PMSAv7_AP_PL1RW_PL0RW, 0, false); #ifdef CONFIG_XIP_KERNEL @@ -448,13 +437,13 @@ void __init mpu_setup(void) * with BG region (which is uncachable), thus we need * to clean and invalidate cache. */ - bool need_flush = region == MPU_RAM_REGION; + bool need_flush = region == PMSAv7_RAM_REGION; if (!xip[i].size) continue; err |= mpu_setup_region(region++, xip[i].base, ilog2(xip[i].size), - MPU_AP_PL1RO_PL0NA | MPU_RGN_NORMAL, + PMSAv7_AP_PL1RO_PL0NA | PMSAv7_RGN_NORMAL, xip[i].subreg, need_flush); } #endif @@ -465,14 +454,14 @@ void __init mpu_setup(void) continue; err |= mpu_setup_region(region++, mem[i].base, ilog2(mem[i].size), - MPU_AP_PL1RW_PL0RW | MPU_RGN_NORMAL, + PMSAv7_AP_PL1RW_PL0RW | PMSAv7_RGN_NORMAL, mem[i].subreg, false); } /* Vectors */ #ifndef CONFIG_CPU_V7M err |= mpu_setup_region(region++, vectors_base, ilog2(2 * PAGE_SIZE), - MPU_AP_PL1RW_PL0NA | MPU_RGN_NORMAL, + PMSAv7_AP_PL1RW_PL0NA | PMSAv7_RGN_NORMAL, 0, false); #endif if (err) { diff --git a/arch/arm/mm/pmsa-v8.c b/arch/arm/mm/pmsa-v8.c new file mode 100644 index 000000000000..617a83def88a --- /dev/null +++ b/arch/arm/mm/pmsa-v8.c @@ -0,0 +1,307 @@ +/* + * Based on linux/arch/arm/pmsa-v7.c + * + * ARM PMSAv8 supporting functions. + */ + +#include <linux/memblock.h> +#include <linux/range.h> + +#include <asm/cp15.h> +#include <asm/cputype.h> +#include <asm/mpu.h> + +#include <asm/memory.h> +#include <asm/sections.h> + +#include "mm.h" + +#ifndef CONFIG_CPU_V7M + +#define PRSEL __ACCESS_CP15(c6, 0, c2, 1) +#define PRBAR __ACCESS_CP15(c6, 0, c3, 0) +#define PRLAR __ACCESS_CP15(c6, 0, c3, 1) + +static inline u32 prlar_read(void) +{ + return read_sysreg(PRLAR); +} + +static inline u32 prbar_read(void) +{ + return read_sysreg(PRBAR); +} + +static inline void prsel_write(u32 v) +{ + write_sysreg(v, PRSEL); +} + +static inline void prbar_write(u32 v) +{ + write_sysreg(v, PRBAR); +} + +static inline void prlar_write(u32 v) +{ + write_sysreg(v, PRLAR); +} +#else + +static inline u32 prlar_read(void) +{ + return readl_relaxed(BASEADDR_V7M_SCB + PMSAv8_RLAR); +} + +static inline u32 prbar_read(void) +{ + return readl_relaxed(BASEADDR_V7M_SCB + PMSAv8_RBAR); +} + +static inline void prsel_write(u32 v) +{ + writel_relaxed(v, BASEADDR_V7M_SCB + PMSAv8_RNR); +} + +static inline void prbar_write(u32 v) +{ + writel_relaxed(v, BASEADDR_V7M_SCB + PMSAv8_RBAR); +} + +static inline void prlar_write(u32 v) +{ + writel_relaxed(v, BASEADDR_V7M_SCB + PMSAv8_RLAR); +} + +#endif + +static struct range __initdata io[MPU_MAX_REGIONS]; +static struct range __initdata mem[MPU_MAX_REGIONS]; + +static unsigned int __initdata mpu_max_regions; + +static __init bool is_region_fixed(int number) +{ + switch (number) { + case PMSAv8_XIP_REGION: + case PMSAv8_KERNEL_REGION: + return true; + default: + return false; + } +} + +void __init pmsav8_adjust_lowmem_bounds(void) +{ + phys_addr_t mem_end; + struct memblock_region *reg; + bool first = true; + + for_each_memblock(memory, reg) { + if (first) { + phys_addr_t phys_offset = PHYS_OFFSET; + + /* + * Initially only use memory continuous from + * PHYS_OFFSET */ + if (reg->base != phys_offset) + panic("First memory bank must be contiguous from PHYS_OFFSET"); + mem_end = reg->base + reg->size; + first = false; + } else { + /* + * memblock auto merges contiguous blocks, remove + * all blocks afterwards in one go (we can't remove + * blocks separately while iterating) + */ + pr_notice("Ignoring RAM after %pa, memory at %pa ignored\n", + &mem_end, ®->base); + memblock_remove(reg->base, 0 - reg->base); + break; + } + } +} + +static int __init __mpu_max_regions(void) +{ + static int max_regions; + u32 mpuir; + + if (max_regions) + return max_regions; + + mpuir = read_cpuid_mputype(); + + max_regions = (mpuir & MPUIR_DREGION_SZMASK) >> MPUIR_DREGION; + + return max_regions; +} + +static int __init __pmsav8_setup_region(unsigned int number, u32 bar, u32 lar) +{ + if (number > mpu_max_regions + || number >= MPU_MAX_REGIONS) + return -ENOENT; + + dsb(); + prsel_write(number); + isb(); + prbar_write(bar); + prlar_write(lar); + + mpu_rgn_info.rgns[number].prbar = bar; + mpu_rgn_info.rgns[number].prlar = lar; + + mpu_rgn_info.used++; + + return 0; +} + +static int __init pmsav8_setup_ram(unsigned int number, phys_addr_t start,phys_addr_t end) +{ + u32 bar, lar; + + if (is_region_fixed(number)) + return -EINVAL; + + bar = start; + lar = (end - 1) & ~(PMSAv8_MINALIGN - 1);; + + bar |= PMSAv8_AP_PL1RW_PL0RW | PMSAv8_RGN_SHARED; + lar |= PMSAv8_LAR_IDX(PMSAv8_RGN_NORMAL) | PMSAv8_LAR_EN; + + return __pmsav8_setup_region(number, bar, lar); +} + +static int __init pmsav8_setup_io(unsigned int number, phys_addr_t start,phys_addr_t end) +{ + u32 bar, lar; + + if (is_region_fixed(number)) + return -EINVAL; + + bar = start; + lar = (end - 1) & ~(PMSAv8_MINALIGN - 1);; + + bar |= PMSAv8_AP_PL1RW_PL0RW | PMSAv8_RGN_SHARED | PMSAv8_BAR_XN; + lar |= PMSAv8_LAR_IDX(PMSAv8_RGN_DEVICE_nGnRnE) | PMSAv8_LAR_EN; + + return __pmsav8_setup_region(number, bar, lar); +} + +static int __init pmsav8_setup_fixed(unsigned int number, phys_addr_t start,phys_addr_t end) +{ + u32 bar, lar; + + if (!is_region_fixed(number)) + return -EINVAL; + + bar = start; + lar = (end - 1) & ~(PMSAv8_MINALIGN - 1); + + bar |= PMSAv8_AP_PL1RW_PL0NA | PMSAv8_RGN_SHARED; + lar |= PMSAv8_LAR_IDX(PMSAv8_RGN_NORMAL) | PMSAv8_LAR_EN; + + prsel_write(number); + isb(); + + if (prbar_read() != bar || prlar_read() != lar) + return -EINVAL; + + /* Reserved region was set up early, we just need a record for secondaries */ + mpu_rgn_info.rgns[number].prbar = bar; + mpu_rgn_info.rgns[number].prlar = lar; + + mpu_rgn_info.used++; + + return 0; +} + +#ifndef CONFIG_CPU_V7M +static int __init pmsav8_setup_vector(unsigned int number, phys_addr_t start,phys_addr_t end) +{ + u32 bar, lar; + + if (number == PMSAv8_KERNEL_REGION) + return -EINVAL; + + bar = start; + lar = (end - 1) & ~(PMSAv8_MINALIGN - 1); + + bar |= PMSAv8_AP_PL1RW_PL0NA | PMSAv8_RGN_SHARED; + lar |= PMSAv8_LAR_IDX(PMSAv8_RGN_NORMAL) | PMSAv8_LAR_EN; + + return __pmsav8_setup_region(number, bar, lar); +} +#endif + +void __init pmsav8_setup(void) +{ + int i, err = 0; + int region = PMSAv8_KERNEL_REGION; + + /* How many regions are supported ? */ + mpu_max_regions = __mpu_max_regions(); + + /* RAM: single chunk of memory */ + add_range(mem, ARRAY_SIZE(mem), 0, memblock.memory.regions[0].base, + memblock.memory.regions[0].base + memblock.memory.regions[0].size); + + /* IO: cover full 4G range */ + add_range(io, ARRAY_SIZE(io), 0, 0, 0xffffffff); + + /* RAM and IO: exclude kernel */ + subtract_range(mem, ARRAY_SIZE(mem), __pa(KERNEL_START), __pa(KERNEL_END)); + subtract_range(io, ARRAY_SIZE(io), __pa(KERNEL_START), __pa(KERNEL_END)); + +#ifdef CONFIG_XIP_KERNEL + /* RAM and IO: exclude xip */ + subtract_range(mem, ARRAY_SIZE(mem), CONFIG_XIP_PHYS_ADDR, __pa(_exiprom)); + subtract_range(io, ARRAY_SIZE(io), CONFIG_XIP_PHYS_ADDR, __pa(_exiprom)); +#endif + +#ifndef CONFIG_CPU_V7M + /* RAM and IO: exclude vectors */ + subtract_range(mem, ARRAY_SIZE(mem), vectors_base, vectors_base + 2 * PAGE_SIZE); + subtract_range(io, ARRAY_SIZE(io), vectors_base, vectors_base + 2 * PAGE_SIZE); +#endif + /* IO: exclude RAM */ + for (i = 0; i < ARRAY_SIZE(mem); i++) + subtract_range(io, ARRAY_SIZE(io), mem[i].start, mem[i].end); + + /* Now program MPU */ + +#ifdef CONFIG_XIP_KERNEL + /* ROM */ + err |= pmsav8_setup_fixed(PMSAv8_XIP_REGION, CONFIG_XIP_PHYS_ADDR, __pa(_exiprom)); +#endif + /* Kernel */ + err |= pmsav8_setup_fixed(region++, __pa(KERNEL_START), __pa(KERNEL_END)); + + + /* IO */ + for (i = 0; i < ARRAY_SIZE(io); i++) { + if (!io[i].end) + continue; + + err |= pmsav8_setup_io(region++, io[i].start, io[i].end); + } + + /* RAM */ + for (i = 0; i < ARRAY_SIZE(mem); i++) { + if (!mem[i].end) + continue; + + err |= pmsav8_setup_ram(region++, mem[i].start, mem[i].end); + } + + /* Vectors */ +#ifndef CONFIG_CPU_V7M + err |= pmsav8_setup_vector(region++, vectors_base, vectors_base + 2 * PAGE_SIZE); +#endif + if (err) + pr_warn("MPU region initialization failure! %d", err); + else + pr_info("Using ARM PMSAv8 Compliant MPU. Used %d of %d regions\n", + mpu_rgn_info.used, mpu_max_regions); +} diff --git a/arch/arm/mm/proc-macros.S b/arch/arm/mm/proc-macros.S index f10e31d0730a..81d0efb055c6 100644 --- a/arch/arm/mm/proc-macros.S +++ b/arch/arm/mm/proc-macros.S @@ -273,13 +273,14 @@ mcr p15, 0, ip, c7, c10, 4 @ data write barrier .endm -.macro define_processor_functions name:req, dabort:req, pabort:req, nommu=0, suspend=0 +.macro define_processor_functions name:req, dabort:req, pabort:req, nommu=0, suspend=0, bugs=0 .type \name\()_processor_functions, #object .align 2 ENTRY(\name\()_processor_functions) .word \dabort .word \pabort .word cpu_\name\()_proc_init + .word \bugs .word cpu_\name\()_proc_fin .word cpu_\name\()_reset .word cpu_\name\()_do_idle diff --git a/arch/arm/mm/proc-v7-2level.S b/arch/arm/mm/proc-v7-2level.S index c6141a5435c3..f8d45ad2a515 100644 --- a/arch/arm/mm/proc-v7-2level.S +++ b/arch/arm/mm/proc-v7-2level.S @@ -41,11 +41,6 @@ * even on Cortex-A8 revisions not affected by 430973. * If IBE is not set, the flush BTAC/BTB won't do anything. */ -ENTRY(cpu_ca8_switch_mm) -#ifdef CONFIG_MMU - mov r2, #0 - mcr p15, 0, r2, c7, c5, 6 @ flush BTAC/BTB -#endif ENTRY(cpu_v7_switch_mm) #ifdef CONFIG_MMU mmid r1, r1 @ get mm->context.id @@ -66,7 +61,6 @@ ENTRY(cpu_v7_switch_mm) #endif bx lr ENDPROC(cpu_v7_switch_mm) -ENDPROC(cpu_ca8_switch_mm) /* * cpu_v7_set_pte_ext(ptep, pte) diff --git a/arch/arm/mm/proc-v7-bugs.c b/arch/arm/mm/proc-v7-bugs.c new file mode 100644 index 000000000000..5544b82a2e7a --- /dev/null +++ b/arch/arm/mm/proc-v7-bugs.c @@ -0,0 +1,174 @@ +// SPDX-License-Identifier: GPL-2.0 +#include <linux/arm-smccc.h> +#include <linux/kernel.h> +#include <linux/psci.h> +#include <linux/smp.h> + +#include <asm/cp15.h> +#include <asm/cputype.h> +#include <asm/proc-fns.h> +#include <asm/system_misc.h> + +#ifdef CONFIG_HARDEN_BRANCH_PREDICTOR +DEFINE_PER_CPU(harden_branch_predictor_fn_t, harden_branch_predictor_fn); + +extern void cpu_v7_iciallu_switch_mm(phys_addr_t pgd_phys, struct mm_struct *mm); +extern void cpu_v7_bpiall_switch_mm(phys_addr_t pgd_phys, struct mm_struct *mm); +extern void cpu_v7_smc_switch_mm(phys_addr_t pgd_phys, struct mm_struct *mm); +extern void cpu_v7_hvc_switch_mm(phys_addr_t pgd_phys, struct mm_struct *mm); + +static void harden_branch_predictor_bpiall(void) +{ + write_sysreg(0, BPIALL); +} + +static void harden_branch_predictor_iciallu(void) +{ + write_sysreg(0, ICIALLU); +} + +static void __maybe_unused call_smc_arch_workaround_1(void) +{ + arm_smccc_1_1_smc(ARM_SMCCC_ARCH_WORKAROUND_1, NULL); +} + +static void __maybe_unused call_hvc_arch_workaround_1(void) +{ + arm_smccc_1_1_hvc(ARM_SMCCC_ARCH_WORKAROUND_1, NULL); +} + +static void cpu_v7_spectre_init(void) +{ + const char *spectre_v2_method = NULL; + int cpu = smp_processor_id(); + + if (per_cpu(harden_branch_predictor_fn, cpu)) + return; + + switch (read_cpuid_part()) { + case ARM_CPU_PART_CORTEX_A8: + case ARM_CPU_PART_CORTEX_A9: + case ARM_CPU_PART_CORTEX_A12: + case ARM_CPU_PART_CORTEX_A17: + case ARM_CPU_PART_CORTEX_A73: + case ARM_CPU_PART_CORTEX_A75: + if (processor.switch_mm != cpu_v7_bpiall_switch_mm) + goto bl_error; + per_cpu(harden_branch_predictor_fn, cpu) = + harden_branch_predictor_bpiall; + spectre_v2_method = "BPIALL"; + break; + + case ARM_CPU_PART_CORTEX_A15: + case ARM_CPU_PART_BRAHMA_B15: + if (processor.switch_mm != cpu_v7_iciallu_switch_mm) + goto bl_error; + per_cpu(harden_branch_predictor_fn, cpu) = + harden_branch_predictor_iciallu; + spectre_v2_method = "ICIALLU"; + break; + +#ifdef CONFIG_ARM_PSCI + default: + /* Other ARM CPUs require no workaround */ + if (read_cpuid_implementor() == ARM_CPU_IMP_ARM) + break; + /* fallthrough */ + /* Cortex A57/A72 require firmware workaround */ + case ARM_CPU_PART_CORTEX_A57: + case ARM_CPU_PART_CORTEX_A72: { + struct arm_smccc_res res; + + if (psci_ops.smccc_version == SMCCC_VERSION_1_0) + break; + + switch (psci_ops.conduit) { + case PSCI_CONDUIT_HVC: + arm_smccc_1_1_hvc(ARM_SMCCC_ARCH_FEATURES_FUNC_ID, + ARM_SMCCC_ARCH_WORKAROUND_1, &res); + if ((int)res.a0 != 0) + break; + if (processor.switch_mm != cpu_v7_hvc_switch_mm && cpu) + goto bl_error; + per_cpu(harden_branch_predictor_fn, cpu) = + call_hvc_arch_workaround_1; + processor.switch_mm = cpu_v7_hvc_switch_mm; + spectre_v2_method = "hypervisor"; + break; + + case PSCI_CONDUIT_SMC: + arm_smccc_1_1_smc(ARM_SMCCC_ARCH_FEATURES_FUNC_ID, + ARM_SMCCC_ARCH_WORKAROUND_1, &res); + if ((int)res.a0 != 0) + break; + if (processor.switch_mm != cpu_v7_smc_switch_mm && cpu) + goto bl_error; + per_cpu(harden_branch_predictor_fn, cpu) = + call_smc_arch_workaround_1; + processor.switch_mm = cpu_v7_smc_switch_mm; + spectre_v2_method = "firmware"; + break; + + default: + break; + } + } +#endif + } + + if (spectre_v2_method) + pr_info("CPU%u: Spectre v2: using %s workaround\n", + smp_processor_id(), spectre_v2_method); + return; + +bl_error: + pr_err("CPU%u: Spectre v2: incorrect context switching function, system vulnerable\n", + cpu); +} +#else +static void cpu_v7_spectre_init(void) +{ +} +#endif + +static __maybe_unused bool cpu_v7_check_auxcr_set(bool *warned, + u32 mask, const char *msg) +{ + u32 aux_cr; + + asm("mrc p15, 0, %0, c1, c0, 1" : "=r" (aux_cr)); + + if ((aux_cr & mask) != mask) { + if (!*warned) + pr_err("CPU%u: %s", smp_processor_id(), msg); + *warned = true; + return false; + } + return true; +} + +static DEFINE_PER_CPU(bool, spectre_warned); + +static bool check_spectre_auxcr(bool *warned, u32 bit) +{ + return IS_ENABLED(CONFIG_HARDEN_BRANCH_PREDICTOR) && + cpu_v7_check_auxcr_set(warned, bit, + "Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable\n"); +} + +void cpu_v7_ca8_ibe(void) +{ + if (check_spectre_auxcr(this_cpu_ptr(&spectre_warned), BIT(6))) + cpu_v7_spectre_init(); +} + +void cpu_v7_ca15_ibe(void) +{ + if (check_spectre_auxcr(this_cpu_ptr(&spectre_warned), BIT(0))) + cpu_v7_spectre_init(); +} + +void cpu_v7_bugs_init(void) +{ + cpu_v7_spectre_init(); +} diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S index b528a15f460d..6fe52819e014 100644 --- a/arch/arm/mm/proc-v7.S +++ b/arch/arm/mm/proc-v7.S @@ -9,6 +9,7 @@ * * This is the "shell" of the ARMv7 processor support. */ +#include <linux/arm-smccc.h> #include <linux/init.h> #include <linux/linkage.h> #include <asm/assembler.h> @@ -93,6 +94,37 @@ ENTRY(cpu_v7_dcache_clean_area) ret lr ENDPROC(cpu_v7_dcache_clean_area) +#ifdef CONFIG_ARM_PSCI + .arch_extension sec +ENTRY(cpu_v7_smc_switch_mm) + stmfd sp!, {r0 - r3} + movw r0, #:lower16:ARM_SMCCC_ARCH_WORKAROUND_1 + movt r0, #:upper16:ARM_SMCCC_ARCH_WORKAROUND_1 + smc #0 + ldmfd sp!, {r0 - r3} + b cpu_v7_switch_mm +ENDPROC(cpu_v7_smc_switch_mm) + .arch_extension virt +ENTRY(cpu_v7_hvc_switch_mm) + stmfd sp!, {r0 - r3} + movw r0, #:lower16:ARM_SMCCC_ARCH_WORKAROUND_1 + movt r0, #:upper16:ARM_SMCCC_ARCH_WORKAROUND_1 + hvc #0 + ldmfd sp!, {r0 - r3} + b cpu_v7_switch_mm +ENDPROC(cpu_v7_smc_switch_mm) +#endif +ENTRY(cpu_v7_iciallu_switch_mm) + mov r3, #0 + mcr p15, 0, r3, c7, c5, 0 @ ICIALLU + b cpu_v7_switch_mm +ENDPROC(cpu_v7_iciallu_switch_mm) +ENTRY(cpu_v7_bpiall_switch_mm) + mov r3, #0 + mcr p15, 0, r3, c7, c5, 6 @ flush BTAC/BTB + b cpu_v7_switch_mm +ENDPROC(cpu_v7_bpiall_switch_mm) + string cpu_v7_name, "ARMv7 Processor" .align @@ -158,31 +190,6 @@ ENTRY(cpu_v7_do_resume) ENDPROC(cpu_v7_do_resume) #endif -/* - * Cortex-A8 - */ - globl_equ cpu_ca8_proc_init, cpu_v7_proc_init - globl_equ cpu_ca8_proc_fin, cpu_v7_proc_fin - globl_equ cpu_ca8_reset, cpu_v7_reset - globl_equ cpu_ca8_do_idle, cpu_v7_do_idle - globl_equ cpu_ca8_dcache_clean_area, cpu_v7_dcache_clean_area - globl_equ cpu_ca8_set_pte_ext, cpu_v7_set_pte_ext - globl_equ cpu_ca8_suspend_size, cpu_v7_suspend_size -#ifdef CONFIG_ARM_CPU_SUSPEND - globl_equ cpu_ca8_do_suspend, cpu_v7_do_suspend - globl_equ cpu_ca8_do_resume, cpu_v7_do_resume -#endif - -/* - * Cortex-A9 processor functions - */ - globl_equ cpu_ca9mp_proc_init, cpu_v7_proc_init - globl_equ cpu_ca9mp_proc_fin, cpu_v7_proc_fin - globl_equ cpu_ca9mp_reset, cpu_v7_reset - globl_equ cpu_ca9mp_do_idle, cpu_v7_do_idle - globl_equ cpu_ca9mp_dcache_clean_area, cpu_v7_dcache_clean_area - globl_equ cpu_ca9mp_switch_mm, cpu_v7_switch_mm - globl_equ cpu_ca9mp_set_pte_ext, cpu_v7_set_pte_ext .globl cpu_ca9mp_suspend_size .equ cpu_ca9mp_suspend_size, cpu_v7_suspend_size + 4 * 2 #ifdef CONFIG_ARM_CPU_SUSPEND @@ -547,12 +554,79 @@ __v7_setup_stack: __INITDATA + .weak cpu_v7_bugs_init + @ define struct processor (see <asm/proc-fns.h> and proc-macros.S) - define_processor_functions v7, dabort=v7_early_abort, pabort=v7_pabort, suspend=1 + define_processor_functions v7, dabort=v7_early_abort, pabort=v7_pabort, suspend=1, bugs=cpu_v7_bugs_init + +#ifdef CONFIG_HARDEN_BRANCH_PREDICTOR + @ generic v7 bpiall on context switch + globl_equ cpu_v7_bpiall_proc_init, cpu_v7_proc_init + globl_equ cpu_v7_bpiall_proc_fin, cpu_v7_proc_fin + globl_equ cpu_v7_bpiall_reset, cpu_v7_reset + globl_equ cpu_v7_bpiall_do_idle, cpu_v7_do_idle + globl_equ cpu_v7_bpiall_dcache_clean_area, cpu_v7_dcache_clean_area + globl_equ cpu_v7_bpiall_set_pte_ext, cpu_v7_set_pte_ext + globl_equ cpu_v7_bpiall_suspend_size, cpu_v7_suspend_size +#ifdef CONFIG_ARM_CPU_SUSPEND + globl_equ cpu_v7_bpiall_do_suspend, cpu_v7_do_suspend + globl_equ cpu_v7_bpiall_do_resume, cpu_v7_do_resume +#endif + define_processor_functions v7_bpiall, dabort=v7_early_abort, pabort=v7_pabort, suspend=1, bugs=cpu_v7_bugs_init + +#define HARDENED_BPIALL_PROCESSOR_FUNCTIONS v7_bpiall_processor_functions +#else +#define HARDENED_BPIALL_PROCESSOR_FUNCTIONS v7_processor_functions +#endif + #ifndef CONFIG_ARM_LPAE - define_processor_functions ca8, dabort=v7_early_abort, pabort=v7_pabort, suspend=1 - define_processor_functions ca9mp, dabort=v7_early_abort, pabort=v7_pabort, suspend=1 + @ Cortex-A8 - always needs bpiall switch_mm implementation + globl_equ cpu_ca8_proc_init, cpu_v7_proc_init + globl_equ cpu_ca8_proc_fin, cpu_v7_proc_fin + globl_equ cpu_ca8_reset, cpu_v7_reset + globl_equ cpu_ca8_do_idle, cpu_v7_do_idle + globl_equ cpu_ca8_dcache_clean_area, cpu_v7_dcache_clean_area + globl_equ cpu_ca8_set_pte_ext, cpu_v7_set_pte_ext + globl_equ cpu_ca8_switch_mm, cpu_v7_bpiall_switch_mm + globl_equ cpu_ca8_suspend_size, cpu_v7_suspend_size +#ifdef CONFIG_ARM_CPU_SUSPEND + globl_equ cpu_ca8_do_suspend, cpu_v7_do_suspend + globl_equ cpu_ca8_do_resume, cpu_v7_do_resume +#endif + define_processor_functions ca8, dabort=v7_early_abort, pabort=v7_pabort, suspend=1, bugs=cpu_v7_ca8_ibe + + @ Cortex-A9 - needs more registers preserved across suspend/resume + @ and bpiall switch_mm for hardening + globl_equ cpu_ca9mp_proc_init, cpu_v7_proc_init + globl_equ cpu_ca9mp_proc_fin, cpu_v7_proc_fin + globl_equ cpu_ca9mp_reset, cpu_v7_reset + globl_equ cpu_ca9mp_do_idle, cpu_v7_do_idle + globl_equ cpu_ca9mp_dcache_clean_area, cpu_v7_dcache_clean_area +#ifdef CONFIG_HARDEN_BRANCH_PREDICTOR + globl_equ cpu_ca9mp_switch_mm, cpu_v7_bpiall_switch_mm +#else + globl_equ cpu_ca9mp_switch_mm, cpu_v7_switch_mm +#endif + globl_equ cpu_ca9mp_set_pte_ext, cpu_v7_set_pte_ext + define_processor_functions ca9mp, dabort=v7_early_abort, pabort=v7_pabort, suspend=1, bugs=cpu_v7_bugs_init #endif + + @ Cortex-A15 - needs iciallu switch_mm for hardening + globl_equ cpu_ca15_proc_init, cpu_v7_proc_init + globl_equ cpu_ca15_proc_fin, cpu_v7_proc_fin + globl_equ cpu_ca15_reset, cpu_v7_reset + globl_equ cpu_ca15_do_idle, cpu_v7_do_idle + globl_equ cpu_ca15_dcache_clean_area, cpu_v7_dcache_clean_area +#ifdef CONFIG_HARDEN_BRANCH_PREDICTOR + globl_equ cpu_ca15_switch_mm, cpu_v7_iciallu_switch_mm +#else + globl_equ cpu_ca15_switch_mm, cpu_v7_switch_mm +#endif + globl_equ cpu_ca15_set_pte_ext, cpu_v7_set_pte_ext + globl_equ cpu_ca15_suspend_size, cpu_v7_suspend_size + globl_equ cpu_ca15_do_suspend, cpu_v7_do_suspend + globl_equ cpu_ca15_do_resume, cpu_v7_do_resume + define_processor_functions ca15, dabort=v7_early_abort, pabort=v7_pabort, suspend=1, bugs=cpu_v7_ca15_ibe #ifdef CONFIG_CPU_PJ4B define_processor_functions pj4b, dabort=v7_early_abort, pabort=v7_pabort, suspend=1 #endif @@ -669,7 +743,7 @@ __v7_ca7mp_proc_info: __v7_ca12mp_proc_info: .long 0x410fc0d0 .long 0xff0ffff0 - __v7_proc __v7_ca12mp_proc_info, __v7_ca12mp_setup + __v7_proc __v7_ca12mp_proc_info, __v7_ca12mp_setup, proc_fns = HARDENED_BPIALL_PROCESSOR_FUNCTIONS .size __v7_ca12mp_proc_info, . - __v7_ca12mp_proc_info /* @@ -679,7 +753,7 @@ __v7_ca12mp_proc_info: __v7_ca15mp_proc_info: .long 0x410fc0f0 .long 0xff0ffff0 - __v7_proc __v7_ca15mp_proc_info, __v7_ca15mp_setup + __v7_proc __v7_ca15mp_proc_info, __v7_ca15mp_setup, proc_fns = ca15_processor_functions .size __v7_ca15mp_proc_info, . - __v7_ca15mp_proc_info /* @@ -689,7 +763,7 @@ __v7_ca15mp_proc_info: __v7_b15mp_proc_info: .long 0x420f00f0 .long 0xff0ffff0 - __v7_proc __v7_b15mp_proc_info, __v7_b15mp_setup, cache_fns = b15_cache_fns + __v7_proc __v7_b15mp_proc_info, __v7_b15mp_setup, proc_fns = ca15_processor_functions, cache_fns = b15_cache_fns .size __v7_b15mp_proc_info, . - __v7_b15mp_proc_info /* @@ -699,9 +773,25 @@ __v7_b15mp_proc_info: __v7_ca17mp_proc_info: .long 0x410fc0e0 .long 0xff0ffff0 - __v7_proc __v7_ca17mp_proc_info, __v7_ca17mp_setup + __v7_proc __v7_ca17mp_proc_info, __v7_ca17mp_setup, proc_fns = HARDENED_BPIALL_PROCESSOR_FUNCTIONS .size __v7_ca17mp_proc_info, . - __v7_ca17mp_proc_info + /* ARM Ltd. Cortex A73 processor */ + .type __v7_ca73_proc_info, #object +__v7_ca73_proc_info: + .long 0x410fd090 + .long 0xff0ffff0 + __v7_proc __v7_ca73_proc_info, __v7_setup, proc_fns = HARDENED_BPIALL_PROCESSOR_FUNCTIONS + .size __v7_ca73_proc_info, . - __v7_ca73_proc_info + + /* ARM Ltd. Cortex A75 processor */ + .type __v7_ca75_proc_info, #object +__v7_ca75_proc_info: + .long 0x410fd0a0 + .long 0xff0ffff0 + __v7_proc __v7_ca75_proc_info, __v7_setup, proc_fns = HARDENED_BPIALL_PROCESSOR_FUNCTIONS + .size __v7_ca75_proc_info, . - __v7_ca75_proc_info + /* * Qualcomm Inc. Krait processors. */ diff --git a/arch/arm/net/bpf_jit_32.c b/arch/arm/net/bpf_jit_32.c index b5030e1a41d8..6e8b71613039 100644 --- a/arch/arm/net/bpf_jit_32.c +++ b/arch/arm/net/bpf_jit_32.c @@ -84,7 +84,7 @@ * * 1. First argument is passed using the arm 32bit registers and rest of the * arguments are passed on stack scratch space. - * 2. First callee-saved arugument is mapped to arm 32 bit registers and rest + * 2. First callee-saved argument is mapped to arm 32 bit registers and rest * arguments are mapped to scratch space on stack. * 3. We need two 64 bit temp registers to do complex operations on eBPF * registers. @@ -234,18 +234,11 @@ static void jit_fill_hole(void *area, unsigned int size) #define SCRATCH_SIZE 80 /* total stack size used in JITed code */ -#define _STACK_SIZE \ - (ctx->prog->aux->stack_depth + \ - + SCRATCH_SIZE + \ - + 4 /* extra for skb_copy_bits buffer */) - -#define STACK_SIZE ALIGN(_STACK_SIZE, STACK_ALIGNMENT) +#define _STACK_SIZE (ctx->prog->aux->stack_depth + SCRATCH_SIZE) +#define STACK_SIZE ALIGN(_STACK_SIZE, STACK_ALIGNMENT) /* Get the offset of eBPF REGISTERs stored on scratch space. */ -#define STACK_VAR(off) (STACK_SIZE-off-4) - -/* Offset of skb_copy_bits buffer */ -#define SKB_BUFFER STACK_VAR(SCRATCH_SIZE) +#define STACK_VAR(off) (STACK_SIZE - off) #if __LINUX_ARM_ARCH__ < 7 @@ -708,7 +701,7 @@ static inline void emit_a32_arsh_r64(const u8 dst[], const u8 src[], bool dstk, } /* dst = dst >> src */ -static inline void emit_a32_lsr_r64(const u8 dst[], const u8 src[], bool dstk, +static inline void emit_a32_rsh_r64(const u8 dst[], const u8 src[], bool dstk, bool sstk, struct jit_ctx *ctx) { const u8 *tmp = bpf2a32[TMP_REG_1]; const u8 *tmp2 = bpf2a32[TMP_REG_2]; @@ -724,7 +717,7 @@ static inline void emit_a32_lsr_r64(const u8 dst[], const u8 src[], bool dstk, emit(ARM_LDR_I(rm, ARM_SP, STACK_VAR(dst_hi)), ctx); } - /* Do LSH operation */ + /* Do RSH operation */ emit(ARM_RSB_I(ARM_IP, rt, 32), ctx); emit(ARM_SUBS_I(tmp2[0], rt, 32), ctx); emit(ARM_MOV_SR(ARM_LR, rd, SRTYPE_LSR, rt), ctx); @@ -774,7 +767,7 @@ static inline void emit_a32_lsh_i64(const u8 dst[], bool dstk, } /* dst = dst >> val */ -static inline void emit_a32_lsr_i64(const u8 dst[], bool dstk, +static inline void emit_a32_rsh_i64(const u8 dst[], bool dstk, const u32 val, struct jit_ctx *ctx) { const u8 *tmp = bpf2a32[TMP_REG_1]; const u8 *tmp2 = bpf2a32[TMP_REG_2]; @@ -1199,8 +1192,8 @@ static int build_insn(const struct bpf_insn *insn, struct jit_ctx *ctx) s32 jmp_offset; #define check_imm(bits, imm) do { \ - if ((((imm) > 0) && ((imm) >> (bits))) || \ - (((imm) < 0) && (~(imm) >> (bits)))) { \ + if ((imm) >= (1 << ((bits) - 1)) || \ + (imm) < -(1 << ((bits) - 1))) { \ pr_info("[%2d] imm=%d(0x%x) out of range\n", \ i, imm, imm); \ return -EINVAL; \ @@ -1330,7 +1323,7 @@ static int build_insn(const struct bpf_insn *insn, struct jit_ctx *ctx) case BPF_ALU64 | BPF_RSH | BPF_K: if (unlikely(imm > 63)) return -EINVAL; - emit_a32_lsr_i64(dst, dstk, imm, ctx); + emit_a32_rsh_i64(dst, dstk, imm, ctx); break; /* dst = dst << src */ case BPF_ALU64 | BPF_LSH | BPF_X: @@ -1338,7 +1331,7 @@ static int build_insn(const struct bpf_insn *insn, struct jit_ctx *ctx) break; /* dst = dst >> src */ case BPF_ALU64 | BPF_RSH | BPF_X: - emit_a32_lsr_r64(dst, src, dstk, sstk, ctx); + emit_a32_rsh_r64(dst, src, dstk, sstk, ctx); break; /* dst = dst >> src (signed) */ case BPF_ALU64 | BPF_ARSH | BPF_X: @@ -1452,83 +1445,6 @@ exit: emit(ARM_LDR_I(rn, ARM_SP, STACK_VAR(src_lo)), ctx); emit_ldx_r(dst, rn, dstk, off, ctx, BPF_SIZE(code)); break; - /* R0 = ntohx(*(size *)(((struct sk_buff *)R6)->data + imm)) */ - case BPF_LD | BPF_ABS | BPF_W: - case BPF_LD | BPF_ABS | BPF_H: - case BPF_LD | BPF_ABS | BPF_B: - /* R0 = ntohx(*(size *)(((struct sk_buff *)R6)->data + src + imm)) */ - case BPF_LD | BPF_IND | BPF_W: - case BPF_LD | BPF_IND | BPF_H: - case BPF_LD | BPF_IND | BPF_B: - { - const u8 r4 = bpf2a32[BPF_REG_6][1]; /* r4 = ptr to sk_buff */ - const u8 r0 = bpf2a32[BPF_REG_0][1]; /*r0: struct sk_buff *skb*/ - /* rtn value */ - const u8 r1 = bpf2a32[BPF_REG_0][0]; /* r1: int k */ - const u8 r2 = bpf2a32[BPF_REG_1][1]; /* r2: unsigned int size */ - const u8 r3 = bpf2a32[BPF_REG_1][0]; /* r3: void *buffer */ - const u8 r6 = bpf2a32[TMP_REG_1][1]; /* r6: void *(*func)(..) */ - int size; - - /* Setting up first argument */ - emit(ARM_MOV_R(r0, r4), ctx); - - /* Setting up second argument */ - emit_a32_mov_i(r1, imm, false, ctx); - if (BPF_MODE(code) == BPF_IND) - emit_a32_alu_r(r1, src_lo, false, sstk, ctx, - false, false, BPF_ADD); - - /* Setting up third argument */ - switch (BPF_SIZE(code)) { - case BPF_W: - size = 4; - break; - case BPF_H: - size = 2; - break; - case BPF_B: - size = 1; - break; - default: - return -EINVAL; - } - emit_a32_mov_i(r2, size, false, ctx); - - /* Setting up fourth argument */ - emit(ARM_ADD_I(r3, ARM_SP, imm8m(SKB_BUFFER)), ctx); - - /* Setting up function pointer to call */ - emit_a32_mov_i(r6, (unsigned int)bpf_load_pointer, false, ctx); - emit_blx_r(r6, ctx); - - emit(ARM_EOR_R(r1, r1, r1), ctx); - /* Check if return address is NULL or not. - * if NULL then jump to epilogue - * else continue to load the value from retn address - */ - emit(ARM_CMP_I(r0, 0), ctx); - jmp_offset = epilogue_offset(ctx); - check_imm24(jmp_offset); - _emit(ARM_COND_EQ, ARM_B(jmp_offset), ctx); - - /* Load value from the address */ - switch (BPF_SIZE(code)) { - case BPF_W: - emit(ARM_LDR_I(r0, r0, 0), ctx); - emit_rev32(r0, r0, ctx); - break; - case BPF_H: - emit(ARM_LDRH_I(r0, r0, 0), ctx); - emit_rev16(r0, r0, ctx); - break; - case BPF_B: - emit(ARM_LDRB_I(r0, r0, 0), ctx); - /* No need to reverse */ - break; - } - break; - } /* ST: *(size *)(dst + off) = imm */ case BPF_ST | BPF_MEM | BPF_W: case BPF_ST | BPF_MEM | BPF_H: diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig index afc1a1d4f7a5..c0a242cae79a 100644 --- a/arch/arm/plat-omap/Kconfig +++ b/arch/arm/plat-omap/Kconfig @@ -115,16 +115,6 @@ config OMAP_SERIAL_WAKE to data on the serial RX line. This allows you to wake the system from serial console. -choice - prompt "OMAP PM layer selection" - depends on ARCH_OMAP - default OMAP_PM_NOOP - -config OMAP_PM_NOOP - bool "No-op/debug PM layer" - -endchoice - endmenu endif diff --git a/arch/arm/plat-samsung/adc.c b/arch/arm/plat-samsung/adc.c index 42bac8d5ab5d..2da35735fa38 100644 --- a/arch/arm/plat-samsung/adc.c +++ b/arch/arm/plat-samsung/adc.c @@ -413,8 +413,7 @@ static int s3c_adc_remove(struct platform_device *pdev) #ifdef CONFIG_PM static int s3c_adc_suspend(struct device *dev) { - struct platform_device *pdev = to_platform_device(dev); - struct adc_device *adc = platform_get_drvdata(pdev); + struct adc_device *adc = dev_get_drvdata(dev); unsigned long flags; u32 con; diff --git a/arch/arm/plat-samsung/include/plat/map-s5p.h b/arch/arm/plat-samsung/include/plat/map-s5p.h index f5769e93544a..d69a0ca09fb5 100644 --- a/arch/arm/plat-samsung/include/plat/map-s5p.h +++ b/arch/arm/plat-samsung/include/plat/map-s5p.h @@ -11,10 +11,6 @@ #define S5P_VA_CHIPID S3C_ADDR(0x02000000) -#define S5P_VA_COREPERI_BASE S3C_ADDR(0x02800000) -#define S5P_VA_COREPERI(x) (S5P_VA_COREPERI_BASE + (x)) -#define S5P_VA_SCU S5P_VA_COREPERI(0x0) - #define VA_VIC(x) (S3C_VA_IRQ + ((x) * 0x10000)) #define VA_VIC0 VA_VIC(0) #define VA_VIC1 VA_VIC(1) diff --git a/arch/arm/probes/kprobes/opt-arm.c b/arch/arm/probes/kprobes/opt-arm.c index bcdecc25461b..b2aa9b32bff2 100644 --- a/arch/arm/probes/kprobes/opt-arm.c +++ b/arch/arm/probes/kprobes/opt-arm.c @@ -165,13 +165,14 @@ optimized_callback(struct optimized_kprobe *op, struct pt_regs *regs) { unsigned long flags; struct kprobe *p = &op->kp; - struct kprobe_ctlblk *kcb = get_kprobe_ctlblk(); + struct kprobe_ctlblk *kcb; /* Save skipped registers */ regs->ARM_pc = (unsigned long)op->kp.addr; regs->ARM_ORIG_r0 = ~0UL; local_irq_save(flags); + kcb = get_kprobe_ctlblk(); if (kprobe_running()) { kprobes_inc_nmissed_count(&op->kp); @@ -191,6 +192,7 @@ optimized_callback(struct optimized_kprobe *op, struct pt_regs *regs) local_irq_restore(flags); } +NOKPROBE_SYMBOL(optimized_callback) int arch_prepare_optimized_kprobe(struct optimized_kprobe *op, struct kprobe *orig) { diff --git a/arch/arm/probes/kprobes/test-core.c b/arch/arm/probes/kprobes/test-core.c index 9ed0129bed3c..14db14152909 100644 --- a/arch/arm/probes/kprobes/test-core.c +++ b/arch/arm/probes/kprobes/test-core.c @@ -766,8 +766,9 @@ static int coverage_start_fn(const struct decode_header *h, void *args) static int coverage_start(const union decode_item *table) { - coverage.base = kmalloc(MAX_COVERAGE_ENTRIES * - sizeof(struct coverage_entry), GFP_KERNEL); + coverage.base = kmalloc_array(MAX_COVERAGE_ENTRIES, + sizeof(struct coverage_entry), + GFP_KERNEL); coverage.num_entries = 0; coverage.nesting = 0; return table_iter(table, coverage_start_fn, &coverage); diff --git a/arch/arm/tools/syscall.tbl b/arch/arm/tools/syscall.tbl index 0bb0e9c6376c..fbc74b5fa3ed 100644 --- a/arch/arm/tools/syscall.tbl +++ b/arch/arm/tools/syscall.tbl @@ -412,3 +412,4 @@ 395 common pkey_alloc sys_pkey_alloc 396 common pkey_free sys_pkey_free 397 common statx sys_statx +398 common rseq sys_rseq diff --git a/arch/arm/vdso/Makefile b/arch/arm/vdso/Makefile index bb4118213fee..f4efff9d3afb 100644 --- a/arch/arm/vdso/Makefile +++ b/arch/arm/vdso/Makefile @@ -30,6 +30,9 @@ CFLAGS_vgettimeofday.o = -O2 # Disable gcov profiling for VDSO code GCOV_PROFILE := n +# Prevents link failures: __sanitizer_cov_trace_pc() is not linked in. +KCOV_INSTRUMENT := n + # Force dependency $(obj)/vdso.o : $(obj)/vdso.so diff --git a/arch/arm/vfp/vfpmodule.c b/arch/arm/vfp/vfpmodule.c index 4c375e11ae95..35d0f823e823 100644 --- a/arch/arm/vfp/vfpmodule.c +++ b/arch/arm/vfp/vfpmodule.c @@ -218,8 +218,7 @@ static void vfp_raise_sigfpe(unsigned int sicode, struct pt_regs *regs) { siginfo_t info; - memset(&info, 0, sizeof(info)); - + clear_siginfo(&info); info.si_signo = SIGFPE; info.si_code = sicode; info.si_addr = (void __user *)(instruction_pointer(regs) - 4); @@ -257,7 +256,7 @@ static void vfp_raise_exceptions(u32 exceptions, u32 inst, u32 fpscr, struct pt_ if (exceptions == VFP_EXCEPTION_ERROR) { vfp_panic("unhandled bounce", inst); - vfp_raise_sigfpe(FPE_FIXME, regs); + vfp_raise_sigfpe(FPE_FLTINV, regs); return; } diff --git a/arch/arm/xen/enlighten.c b/arch/arm/xen/enlighten.c index ba7f4c8f5c3e..8073625371f5 100644 --- a/arch/arm/xen/enlighten.c +++ b/arch/arm/xen/enlighten.c @@ -89,6 +89,17 @@ int xen_unmap_domain_gfn_range(struct vm_area_struct *vma, } EXPORT_SYMBOL_GPL(xen_unmap_domain_gfn_range); +/* Not used by XENFEAT_auto_translated guests. */ +int xen_remap_domain_mfn_array(struct vm_area_struct *vma, + unsigned long addr, + xen_pfn_t *mfn, int nr, + int *err_ptr, pgprot_t prot, + unsigned int domid, struct page **pages) +{ + return -ENOSYS; +} +EXPORT_SYMBOL_GPL(xen_remap_domain_mfn_array); + static void xen_read_wallclock(struct timespec64 *ts) { u32 version; |