diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom')
18 files changed, 776 insertions, 1137 deletions
diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts index 9dee131b1e24..70fd9ff8dfa2 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts @@ -481,287 +481,261 @@ }; &qspi_clk { - pinconf { - pins = "gpio63"; - bias-disable; - }; + bias-disable; }; &qspi_cs0 { - pinconf { - pins = "gpio68"; - bias-disable; - }; + bias-disable; }; &qspi_data01 { - pinconf { - pins = "gpio64", "gpio65"; - - /* High-Z when no transfers; nice to park the lines */ - bias-pull-up; - }; + /* High-Z when no transfers; nice to park the lines */ + bias-pull-up; }; &qup_i2c2_default { - pinconf { - pins = "gpio15", "gpio16"; - drive-strength = <2>; + drive-strength = <2>; - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; &qup_i2c4_default { - pinconf { - pins = "gpio115", "gpio116"; - drive-strength = <2>; + drive-strength = <2>; - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; &qup_i2c7_default { - pinconf { - pins = "gpio6", "gpio7"; - drive-strength = <2>; + drive-strength = <2>; - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; &qup_i2c9_default { - pinconf { - pins = "gpio46", "gpio47"; - drive-strength = <2>; + drive-strength = <2>; - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; -&qup_uart3_default { - pinconf-cts { - /* - * Configure a pull-down on CTS to match the pull of - * the Bluetooth module. - */ - pins = "gpio38"; - bias-pull-down; - }; +&qup_uart3_cts { + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + bias-pull-down; +}; - pinconf-rts { - /* We'll drive RTS, so no pull */ - pins = "gpio39"; - drive-strength = <2>; - bias-disable; - }; +&qup_uart3_rts { + /* We'll drive RTS, so no pull */ + drive-strength = <2>; + bias-disable; +}; - pinconf-tx { - /* We'll drive TX, so no pull */ - pins = "gpio40"; - drive-strength = <2>; - bias-disable; - }; +&qup_uart3_tx { + /* We'll drive TX, so no pull */ + drive-strength = <2>; + bias-disable; +}; - pinconf-rx { - /* - * Configure a pull-up on RX. This is needed to avoid - * garbage data when the TX pin of the Bluetooth module is - * in tri-state (module powered off or not driving the - * signal yet). - */ - pins = "gpio41"; - bias-pull-up; - }; +&qup_uart3_rx { + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module is + * in tri-state (module powered off or not driving the + * signal yet). + */ + bias-pull-up; }; -&qup_uart8_default { - pinconf-tx { - pins = "gpio44"; - drive-strength = <2>; - bias-disable; - }; +&qup_uart8_tx { + drive-strength = <2>; + bias-disable; +}; - pinconf-rx { - pins = "gpio45"; - drive-strength = <2>; - bias-pull-up; - }; +&qup_uart8_rx { + drive-strength = <2>; + bias-pull-up; }; -&qup_spi0_default { - pinconf { - pins = "gpio34", "gpio35", "gpio36", "gpio37"; - drive-strength = <2>; - bias-disable; - }; +&qup_spi0_spi { + drive-strength = <2>; + bias-disable; }; -&qup_spi6_default { - pinconf { - pins = "gpio59", "gpio60", "gpio61", "gpio62"; - drive-strength = <2>; - bias-disable; - }; +&qup_spi0_cs { + drive-strength = <2>; + bias-disable; }; -&qup_spi10_default { - pinconf { - pins = "gpio86", "gpio87", "gpio88", "gpio89"; - drive-strength = <2>; - bias-disable; - }; +&qup_spi6_spi { + drive-strength = <2>; + bias-disable; }; -&tlmm { - qup_uart3_sleep: qup-uart3-sleep { - pinmux { - pins = "gpio38", "gpio39", - "gpio40", "gpio41"; - function = "gpio"; - }; +&qup_spi6_cs { + drive-strength = <2>; + bias-disable; +}; + +&qup_spi10_spi { + drive-strength = <2>; + bias-disable; +}; + +&qup_spi10_cs { + drive-strength = <2>; + bias-disable; +}; - pinconf-cts { +&tlmm { + qup_uart3_sleep: qup-uart3-sleep-state { + cts-pins { /* * Configure a pull-down on CTS to match the pull of * the Bluetooth module. */ pins = "gpio38"; + function = "gpio"; bias-pull-down; }; - pinconf-rts { + rts-pins { /* * Configure pull-down on RTS. As RTS is active low * signal, pull it low to indicate the BT SoC that it * can wakeup the system anytime from suspend state by * pulling RX low (by sending wakeup bytes). */ - pins = "gpio39"; - bias-pull-down; + pins = "gpio39"; + function = "gpio"; + bias-pull-down; }; - pinconf-tx { + tx-pins { /* * Configure pull-up on TX when it isn't actively driven * to prevent BT SoC from receiving garbage during sleep. */ pins = "gpio40"; + function = "gpio"; bias-pull-up; }; - pinconf-rx { + rx-pins { /* * Configure a pull-up on RX. This is needed to avoid * garbage data when the TX pin of the Bluetooth module * is floating which may cause spurious wakeups. */ pins = "gpio41"; + function = "gpio"; bias-pull-up; }; }; - sdc1_on: sdc1-on { - pinconf-clk { + sdc1_on: sdc1-on-state { + clk-pins { pins = "sdc1_clk"; bias-disable; drive-strength = <16>; }; - pinconf-cmd { + cmd-pins { pins = "sdc1_cmd"; bias-pull-up; drive-strength = <10>; }; - pinconf-data { + data-pins { pins = "sdc1_data"; bias-pull-up; drive-strength = <10>; }; - pinconf-rclk { + rclk-pins { pins = "sdc1_rclk"; bias-pull-down; }; }; - sdc1_off: sdc1-off { - pinconf-clk { + sdc1_off: sdc1-off-state { + clk-pins { pins = "sdc1_clk"; bias-disable; drive-strength = <2>; }; - pinconf-cmd { + cmd-pins { pins = "sdc1_cmd"; bias-pull-up; drive-strength = <2>; }; - pinconf-data { + data-pins { pins = "sdc1_data"; bias-pull-up; drive-strength = <2>; }; - pinconf-rclk { + rclk-pins { pins = "sdc1_rclk"; bias-pull-down; }; }; - sdc2_on: sdc2-on { - pinconf-clk { + sdc2_on: sdc2-on-state { + clk-pins { pins = "sdc2_clk"; bias-disable; drive-strength = <16>; }; - pinconf-cmd { + cmd-pins { pins = "sdc2_cmd"; bias-pull-up; drive-strength = <10>; }; - pinconf-data { + data-pins { pins = "sdc2_data"; bias-pull-up; drive-strength = <10>; }; - pinconf-sd-cd { + sd-cd-pins { pins = "gpio69"; + function = "gpio"; bias-pull-up; drive-strength = <2>; }; }; - sdc2_off: sdc2-off { - pinconf-clk { + sdc2_off: sdc2-off-state { + clk-pins { pins = "sdc2_clk"; bias-disable; drive-strength = <2>; }; - pinconf-cmd { + cmd-pins { pins = "sdc2_cmd"; bias-pull-up; drive-strength = <2>; }; - pinconf-data { + data-pins { pins = "sdc2_data"; bias-pull-up; drive-strength = <2>; }; - pinconf-sd-cd { + sd-cd-pins { pins = "gpio69"; + function = "gpio"; bias-pull-up; drive-strength = <2>; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi index 1ce73187a562..8b8ea8af165d 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi @@ -181,23 +181,15 @@ ap_ts_pen_1v8: &i2c4 { /* PINCTRL - modifications to sc7180-trogdor.dtsi */ &en_pp3300_dx_edp { - pinmux { - pins = "gpio67"; - }; - - pinconf { - pins = "gpio67"; - }; + pins = "gpio67"; }; &ts_reset_l { - pinconf { - /* - * We want reset state by default and it will be up to the - * driver to disable this when it's ready. - */ - output-low; - }; + /* + * We want reset state by default and it will be up to the + * driver to disable this when it's ready. + */ + output-low; }; /* PINCTRL - board-specific pinctrl */ @@ -327,16 +319,10 @@ ap_ts_pen_1v8: &i2c4 { "DP_HOT_PLUG_DET", "EC_IN_RW_ODL"; - dmic_clk_en: dmic_clk_en { - pinmux { - pins = "gpio83"; - function = "gpio"; - }; - - pinconf { - pins = "gpio83"; - drive-strength = <8>; - bias-pull-up; - }; + dmic_clk_en: dmic-clk-en-state { + pins = "gpio83"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; }; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi index 8264b8d5e778..70e52fdb606a 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi @@ -180,36 +180,19 @@ ap_ts_pen_1v8: &i2c4 { /* PINCTRL - modifications to sc7180-trogdor.dtsi */ &en_pp3300_dx_edp { - pinmux { - pins = "gpio67"; - }; - - pinconf { - pins = "gpio67"; - }; + pins = "gpio67"; }; &sec_mi2s_active { - pinmux { - pins = "gpio49", "gpio50", "gpio51", "gpio52"; - function = "mi2s_1"; - }; - - pinconf { - pins = "gpio49", "gpio50", "gpio51", "gpio52"; - drive-strength = <2>; - bias-pull-down; - }; + pins = "gpio49", "gpio50", "gpio51", "gpio52"; }; &ts_reset_l { - pinconf { - /* - * We want reset state by default and it will be up to the - * driver to disable this when it's ready. - */ - output-low; - }; + /* + * We want reset state by default and it will be up to the + * driver to disable this when it's ready. + */ + output-low; }; /* PINCTRL - board-specific pinctrl */ @@ -339,16 +322,10 @@ ap_ts_pen_1v8: &i2c4 { "DP_HOT_PLUG_DET", "EC_IN_RW_ODL"; - en_pp3300_touch: en-pp3300-touch { - pinmux { - pins = "gpio87"; - function = "gpio"; - }; - - pinconf { - pins = "gpio87"; - drive-strength = <2>; - bias-disable; - }; + en_pp3300_touch: en-pp3300-touch-state { + pins = "gpio87"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown-r0.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown-r0.dts index 1a62e8d435ab..3abd6222fe46 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown-r0.dts +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown-r0.dts @@ -29,16 +29,10 @@ }; &tlmm { - en_fp_rails: en-fp-rails { - pinmux { - pins = "gpio74"; - function = "gpio"; - }; - - pinconf { - pins = "gpio74"; - drive-strength = <2>; - bias-disable; - }; + en_fp_rails: en-fp-rails-state { + pins = "gpio74"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown.dtsi index 74f0e07ea5cf..4156ad6dbd96 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown.dtsi @@ -87,13 +87,7 @@ ap_ts_pen_1v8: &i2c4 { /* PINCTRL - modifications to sc7180-trogdor.dtsi */ &en_pp3300_dx_edp { - pinmux { - pins = "gpio67"; - }; - - pinconf { - pins = "gpio67"; - }; + pins = "gpio67"; }; /* PINCTRL - board-specific pinctrl */ diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi index 002663d752da..269007d73162 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi @@ -75,21 +75,13 @@ ap_ts_pen_1v8: &i2c4 { /* PINCTRL - modifications to sc7180-trogdor.dtsi */ &trackpad_int_1v8_odl { - pinmux { - pins = "gpio58"; - }; - - pinconf { - pins = "gpio58"; - }; + pins = "gpio58"; }; &ts_reset_l { - pinconf { - /* This pin is not connected on -rev0, pull up to park. */ - /delete-property/bias-disable; - bias-pull-up; - }; + /* This pin is not connected on -rev0, pull up to park. */ + /delete-property/bias-disable; + bias-pull-up; }; /* PINCTRL - board-specific pinctrl */ diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0.dtsi index 7bc8402c018e..f4c1f3813664 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0.dtsi @@ -24,30 +24,13 @@ /* PINCTRL - modifications to sc7180-trogdor-mrbland.dtsi */ &avdd_lcd_en { - pinmux { - pins = "gpio80"; - }; - - pinconf { - pins = "gpio80"; - }; + pins = "gpio80"; }; &mipi_1800_en { - pinmux { - pins = "gpio81"; - }; - - pinconf { - pins = "gpio81"; - }; + pins = "gpio81"; }; -&vdd_reset_1800 { - pinmux { - pins = "gpio76"; - }; - pinconf { - pins = "gpio76"; - }; +&vdd_reset_1800 { + pins = "gpio76"; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland.dtsi index 97cba7f8064f..5e563655baec 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland.dtsi @@ -160,13 +160,7 @@ pp3300_disp_on: &pp3300_dx_edp { */ tp_en: &en_pp3300_dx_edp { - pinmux { - pins = "gpio85"; - }; - - pinconf { - pins = "gpio85"; - }; + pins = "gpio85"; }; /* PINCTRL - board-specific pinctrl */ @@ -296,55 +290,31 @@ tp_en: &en_pp3300_dx_edp { "DP_HOT_PLUG_DET", "EC_IN_RW_ODL"; - avdd_lcd_en: avdd-lcd-en { - pinmux { - pins = "gpio88"; - function = "gpio"; - }; - - pinconf { - pins = "gpio88"; - drive-strength = <2>; - bias-disable; - }; + avdd_lcd_en: avdd-lcd-en-state { + pins = "gpio88"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - avee_lcd_en: avee-lcd-en { - pinmux { - pins = "gpio21"; - function = "gpio"; - }; - - pinconf { - pins = "gpio21"; - drive-strength = <2>; - bias-disable; - }; + avee_lcd_en: avee-lcd-en-state { + pins = "gpio21"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - mipi_1800_en: mipi-1800-en { - pinmux { - pins = "gpio86"; - function = "gpio"; - }; - - pinconf { - pins = "gpio86"; - drive-strength = <2>; - bias-disable; - }; + mipi_1800_en: mipi-1800-en-state { + pins = "gpio86"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - vdd_reset_1800: vdd-reset-1800 { - pinmux { - pins = "gpio87"; - function = "gpio"; - }; - - pinconf { - pins = "gpio87"; - drive-strength = <2>; - bias-disable; - }; + vdd_reset_1800: vdd-reset-1800-state { + pins = "gpio87"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-parade-ps8640.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-parade-ps8640.dtsi index 6a84fba178d6..070b3acb7baa 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-parade-ps8640.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-parade-ps8640.dtsi @@ -83,29 +83,17 @@ edp_brij_i2c: &i2c2 { }; &tlmm { - edp_brij_ps8640_rst: edp-brij-ps8640-rst { - pinmux { - pins = "gpio11"; - function = "gpio"; - }; - - pinconf { - pins = "gpio11"; - drive-strength = <2>; - bias-disable; - }; + edp_brij_ps8640_rst: edp-brij-ps8640-rst-state { + pins = "gpio11"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - en_pp3300_edp_brij_ps8640: en-pp3300-edp-brij-ps8640 { - pinmux { - pins = "gpio32"; - function = "gpio"; - }; - - pinconf { - pins = "gpio32"; - drive-strength = <2>; - bias-disable; - }; + en_pp3300_edp_brij_ps8640: en-pp3300-edp-brij-ps8640-state { + pins = "gpio32"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel.dtsi index 56d787785fd5..d06cc4ea3375 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel.dtsi @@ -84,13 +84,7 @@ }; &en_pp3300_dx_edp { - pinmux { - pins = "gpio67"; - }; - - pinconf { - pins = "gpio67"; - }; + pins = "gpio67"; }; /* PINCTRL - board-specific pinctrl */ diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi index a7582fb547ee..6c5287bd27d6 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi @@ -312,15 +312,9 @@ ap_ts_pen_1v8: &i2c4 { "DP_HOT_PLUG_DET", "EC_IN_RW_ODL"; - dmic_sel: dmic-sel { - pinmux { - pins = "gpio86"; - function = "gpio"; - }; - - pinconf { - pins = "gpio86"; - bias-pull-down; - }; + dmic_sel: dmic-sel-state { + pins = "gpio86"; + function = "gpio"; + bias-pull-down; }; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi index 695b04fe7221..c1367999eafb 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi @@ -147,13 +147,7 @@ pp3300_disp_on: &pp3300_dx_edp { */ tp_en: &en_pp3300_dx_edp { - pinmux { - pins = "gpio67"; - }; - - pinconf { - pins = "gpio67"; - }; + pins = "gpio67"; }; /* PINCTRL - board-specific pinctrl */ @@ -283,42 +277,24 @@ tp_en: &en_pp3300_dx_edp { "DP_HOT_PLUG_DET", "EC_IN_RW_ODL"; - lcd_rst: lcd-rst { - pinmux { - pins = "gpio87"; - function = "gpio"; - }; - - pinconf { - pins = "gpio87"; - drive-strength = <2>; - bias-disable; - }; + lcd_rst: lcd-rst-state { + pins = "gpio87"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - ppvar_lcd_en: ppvar-lcd-en { - pinmux { - pins = "gpio88"; - function = "gpio"; - }; - - pinconf { - pins = "gpio88"; - drive-strength = <2>; - bias-disable; - }; + ppvar_lcd_en: ppvar-lcd-en-state { + pins = "gpio88"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - pp1800_disp_on: pp1800-disp-on { - pinmux { - pins = "gpio86"; - function = "gpio"; - }; - - pinconf { - pins = "gpio86"; - drive-strength = <2>; - bias-disable; - }; + pp1800_disp_on: pp1800-disp-on-state { + pins = "gpio86"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts index bc097d1b1b23..671b3691f1bb 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts @@ -63,13 +63,7 @@ ap_ts_pen_1v8: &i2c4 { /* PINCTRL - modifications to sc7180-trogdor.dtsi */ &trackpad_int_1v8_odl { - pinmux { - pins = "gpio58"; - }; - - pinconf { - pins = "gpio58"; - }; + pins = "gpio58"; }; /* PINCTRL - board-specific pinctrl */ diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi index f869e6a343c1..65333709e529 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi @@ -76,16 +76,10 @@ edp_brij_i2c: &i2c2 { }; &tlmm { - edp_brij_irq: edp-brij-irq { - pinmux { - pins = "gpio11"; - function = "gpio"; - }; - - pinconf { - pins = "gpio11"; - drive-strength = <2>; - bias-pull-down; - }; + edp_brij_irq: edp-brij-irq-state { + pins = "gpio11"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; }; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0.dtsi index db29e0cba29d..7f272c6e95f6 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0.dtsi @@ -24,30 +24,13 @@ /* PINCTRL - modifications to sc7180-trogdor-wormdingler.dtsi */ &avdd_lcd_en { - pinmux { - pins = "gpio80"; - }; - - pinconf { - pins = "gpio80"; - }; + pins = "gpio80"; }; &mipi_1800_en { - pinmux { - pins = "gpio81"; - }; - - pinconf { - pins = "gpio81"; - }; + pins = "gpio81"; }; -&vdd_reset_1800 { - pinmux { - pins = "gpio76"; - }; - pinconf { - pins = "gpio76"; - }; +&vdd_reset_1800 { + pins = "gpio76"; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler.dtsi index 6312108e8b3e..123989ba97e1 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler.dtsi @@ -222,13 +222,7 @@ pp3300_disp_on: &pp3300_dx_edp { */ tp_en: &en_pp3300_dx_edp { - pinmux { - pins = "gpio85"; - }; - - pinconf { - pins = "gpio85"; - }; + pins = "gpio85"; }; /* PINCTRL - board-specific pinctrl */ @@ -358,55 +352,31 @@ tp_en: &en_pp3300_dx_edp { "DP_HOT_PLUG_DET", "EC_IN_RW_ODL"; - avdd_lcd_en: avdd-lcd-en { - pinmux { - pins = "gpio88"; - function = "gpio"; - }; - - pinconf { - pins = "gpio88"; - drive-strength = <2>; - bias-disable; - }; + avdd_lcd_en: avdd-lcd-en-state { + pins = "gpio88"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - avee_lcd_en: avee-lcd-en { - pinmux { - pins = "gpio21"; - function = "gpio"; - }; - - pinconf { - pins = "gpio21"; - drive-strength = <2>; - bias-disable; - }; + avee_lcd_en: avee-lcd-en-state { + pins = "gpio21"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - mipi_1800_en: mipi-1800-en { - pinmux { - pins = "gpio86"; - function = "gpio"; - }; - - pinconf { - pins = "gpio86"; - drive-strength = <2>; - bias-disable; - }; + mipi_1800_en: mipi-1800-en-state { + pins = "gpio86"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - vdd_reset_1800: vdd-reset-1800 { - pinmux { - pins = "gpio87"; - function = "gpio"; - }; - - pinconf { - pins = "gpio87"; - drive-strength = <2>; - bias-disable; - }; + vdd_reset_1800: vdd-reset-1800-state { + pins = "gpio87"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi index 33817358ebb0..4a5ea17a15ba 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi @@ -880,17 +880,17 @@ hp_i2c: &i2c9 { }; &spi0 { - pinctrl-0 = <&qup_spi0_cs_gpio>; + pinctrl-0 = <&qup_spi0_spi>, <&qup_spi0_cs_gpio>; cs-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>; }; &spi6 { - pinctrl-0 = <&qup_spi6_cs_gpio>; + pinctrl-0 = <&qup_spi6_spi>, <&qup_spi6_cs_gpio>; cs-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; }; ap_spi_fp: &spi10 { - pinctrl-0 = <&qup_spi10_cs_gpio>; + pinctrl-0 = <&qup_spi10_spi>, <&qup_spi10_cs_gpio>; cs-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>; cros_ec_fp: ec@0 { @@ -997,175 +997,141 @@ ap_spi_fp: &spi10 { /* PINCTRL - additions to nodes defined in sc7180.dtsi */ &dp_hot_plug_det { - pinconf { - pins = "gpio117"; - bias-disable; - }; + bias-disable; }; &pri_mi2s_active { - pinconf { - pins = "gpio53", "gpio54", "gpio55", "gpio56"; - drive-strength = <2>; - bias-pull-down; - }; + drive-strength = <2>; + bias-pull-down; }; &pri_mi2s_mclk_active { - pinconf { - pins = "gpio57"; - drive-strength = <2>; - bias-pull-down; - }; + drive-strength = <2>; + bias-pull-down; }; &qspi_cs0 { - pinconf { - pins = "gpio68"; - bias-disable; - }; + bias-disable; }; &qspi_clk { - pinconf { - pins = "gpio63"; - drive-strength = <8>; - bias-disable; - }; + drive-strength = <8>; + bias-disable; }; &qspi_data01 { - pinconf { - pins = "gpio64", "gpio65"; - - /* High-Z when no transfers; nice to park the lines */ - bias-pull-up; - }; + /* High-Z when no transfers; nice to park the lines */ + bias-pull-up; }; &qup_i2c2_default { - pinconf { - pins = "gpio15", "gpio16"; - drive-strength = <2>; + drive-strength = <2>; - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; &qup_i2c4_default { - pinconf { - pins = "gpio115", "gpio116"; - drive-strength = <2>; + drive-strength = <2>; - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; &qup_i2c5_default { - pinconf { - pins = "gpio25", "gpio26"; - drive-strength = <2>; + drive-strength = <2>; - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; &qup_i2c7_default { - pinconf { - pins = "gpio6", "gpio7"; - drive-strength = <2>; + drive-strength = <2>; - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; &qup_i2c9_default { - pinconf { - pins = "gpio46", "gpio47"; - drive-strength = <2>; + drive-strength = <2>; - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; +}; + +&qup_spi0_spi { + drive-strength = <2>; + bias-disable; }; &qup_spi0_cs_gpio { - pinconf { - pins = "gpio34", "gpio35", "gpio36", "gpio37"; - drive-strength = <2>; - bias-disable; - }; + drive-strength = <2>; + bias-disable; +}; + +&qup_spi6_spi { + drive-strength = <2>; + bias-disable; }; &qup_spi6_cs_gpio { - pinconf { - pins = "gpio59", "gpio60", "gpio61", "gpio62"; - drive-strength = <2>; - bias-disable; - }; + drive-strength = <2>; + bias-disable; +}; + +&qup_spi10_spi { + drive-strength = <2>; + bias-disable; }; &qup_spi10_cs_gpio { - pinconf { - pins = "gpio86", "gpio87", "gpio88", "gpio89"; - drive-strength = <2>; - bias-disable; - }; + drive-strength = <2>; + bias-disable; }; -&qup_uart3_default { - pinconf-cts { - /* - * Configure a pull-down on CTS to match the pull of - * the Bluetooth module. - */ - pins = "gpio38"; - bias-pull-down; - }; +&qup_uart3_cts { + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + bias-pull-down; +}; - pinconf-rts-tx { - /* We'll drive RTS and TX, so no pull */ - pins = "gpio39", "gpio40"; - drive-strength = <2>; - bias-disable; - }; +&qup_uart3_rts { + /* We'll drive RTS, so no pull */ + drive-strength = <2>; + bias-disable; +}; - pinconf-rx { - /* - * Configure a pull-up on RX. This is needed to avoid - * garbage data when the TX pin of the Bluetooth module is - * in tri-state (module powered off or not driving the - * signal yet). - */ - pins = "gpio41"; - bias-pull-up; - }; +&qup_uart3_tx { + /* We'll drive TX, so no pull */ + drive-strength = <2>; + bias-disable; }; -&qup_uart8_default { - pinconf-tx { - pins = "gpio44"; - drive-strength = <2>; - bias-disable; - }; +&qup_uart3_rx { + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module is + * in tri-state (module powered off or not driving the + * signal yet). + */ + bias-pull-up; +}; - pinconf-rx { - pins = "gpio45"; - drive-strength = <2>; - bias-pull-up; - }; +&qup_uart8_tx { + drive-strength = <2>; + bias-disable; +}; + +&qup_uart8_rx { + drive-strength = <2>; + bias-pull-up; }; &sec_mi2s_active { - pinconf { - pins = "gpio49", "gpio50", "gpio51"; - drive-strength = <2>; - bias-pull-down; - }; + drive-strength = <2>; + bias-pull-down; }; /* PINCTRL - board-specific pinctrl */ @@ -1196,447 +1162,324 @@ ap_spi_fp: &spi10 { pinctrl-names = "default"; pinctrl-0 = <&bios_flash_wp_l>, <&ap_suspend_l_neuter>; - amp_en: amp-en { - pinmux { - pins = "gpio23"; - function = "gpio"; - }; - - pinconf { - pins = "gpio23"; - bias-pull-down; - }; + amp_en: amp-en-state { + pins = "gpio23"; + function = "gpio"; + bias-pull-down; }; - ap_ec_int_l: ap-ec-int-l { - pinmux { - pins = "gpio94"; - function = "gpio"; - input-enable; - }; - - pinconf { - pins = "gpio94"; - bias-pull-up; - }; + ap_ec_int_l: ap-ec-int-l-state { + pins = "gpio94"; + function = "gpio"; + input-enable; + bias-pull-up; }; - ap_edp_bklten: ap-edp-bklten { - pinmux { - pins = "gpio12"; - function = "gpio"; - }; - - pinconf { - pins = "gpio12"; - drive-strength = <2>; - bias-disable; + ap_edp_bklten: ap-edp-bklten-state { + pins = "gpio12"; + function = "gpio"; + drive-strength = <2>; + bias-disable; - /* Force backlight to be disabled to match state at boot. */ - output-low; - }; + /* Force backlight to be disabled to match state at boot. */ + output-low; }; - ap_suspend_l_neuter: ap-suspend-l-neuter { - pinmux { - pins = "gpio27"; - function = "gpio"; - }; - - pinconf { - pins = "gpio27"; - bias-disable; - }; + ap_suspend_l_neuter: ap-suspend-l-neuter-state { + pins = "gpio27"; + function = "gpio"; + bias-disable; }; - bios_flash_wp_l: bios-flash-wp-l { - pinmux { - pins = "gpio66"; - function = "gpio"; - input-enable; - }; - - pinconf { - pins = "gpio66"; - bias-disable; - }; + bios_flash_wp_l: bios-flash-wp-l-state { + pins = "gpio66"; + function = "gpio"; + input-enable; + bias-disable; }; - edp_brij_en: edp-brij-en { - pinmux { - pins = "gpio104"; - function = "gpio"; - }; - - pinconf { - pins = "gpio104"; - drive-strength = <2>; - bias-disable; - }; + edp_brij_en: edp-brij-en-state { + pins = "gpio104"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - en_pp3300_codec: en-pp3300-codec { - pinmux { - pins = "gpio83"; - function = "gpio"; - }; - - pinconf { - pins = "gpio83"; - drive-strength = <2>; - bias-disable; - }; + en_pp3300_codec: en-pp3300-codec-state { + pins = "gpio83"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - en_pp3300_dx_edp: en-pp3300-dx-edp { - pinmux { - pins = "gpio30"; - function = "gpio"; - }; - - pinconf { - pins = "gpio30"; - drive-strength = <2>; - bias-disable; - }; + en_pp3300_dx_edp: en-pp3300-dx-edp-state { + pins = "gpio30"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - en_pp3300_hub: en-pp3300-hub { - pinmux { - pins = "gpio84"; - function = "gpio"; - }; - - pinconf { - pins = "gpio84"; - drive-strength = <2>; - bias-disable; - }; + en_pp3300_hub: en-pp3300-hub-state { + pins = "gpio84"; + function = "gpio"; + drive-strength = <2>; + bias-disable; }; - fp_to_ap_irq_l: fp-to-ap-irq-l { - pinmux { - pins = "gpio4"; - function = "gpio"; - input-enable; - }; + fp_to_ap_irq_l: fp-to-ap-irq-l-state { + pins = "gpio4"; + function = "gpio"; + input-enable; - pinconf { - pins = "gpio4"; - - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; - h1_ap_int_odl: h1-ap-int-odl { - pinmux { - pins = "gpio42"; - function = "gpio"; - input-enable; - }; - - pinconf { - pins = "gpio42"; - bias-pull-up; - }; + h1_ap_int_odl: h1-ap-int-odl-state { + pins = "gpio42"; + function = "gpio"; + input-enable; + bias-pull-up; }; - hp_irq: hp-irq { - pinmux { - pins = "gpio28"; - function = "gpio"; - }; - - pinconf { - pins = "gpio28"; - bias-pull-up; - }; + hp_irq: hp-irq-state { + pins = "gpio28"; + function = "gpio"; + bias-pull-up; }; - pen_irq_l: pen-irq-l { - pinmux { - pins = "gpio21"; - function = "gpio"; - }; - - pinconf { - pins = "gpio21"; + pen_irq_l: pen-irq-l-state { + pins = "gpio21"; + function = "gpio"; - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; - pen_pdct_l: pen-pdct-l { - pinmux { - pins = "gpio52"; - function = "gpio"; - }; + pen_pdct_l: pen-pdct-l-state-state { + pins = "gpio52"; + function = "gpio"; - pinconf { - pins = "gpio52"; - - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; - pen_rst_odl: pen-rst-odl { - pinmux { - pins = "gpio18"; - function = "gpio"; - }; - - pinconf { - pins = "gpio18"; - bias-disable; - drive-strength = <2>; + pen_rst_odl: pen-rst-odl-state { + pins = "gpio18"; + function = "gpio"; + bias-disable; + drive-strength = <2>; - /* - * The pen driver doesn't currently support - * driving this reset line. By specifying - * output-high here we're relying on the fact - * that this pin has a default pulldown at boot - * (which makes sure the pen was in reset if it - * was powered) and then we set it high here to - * take it out of reset. Better would be if the - * pen driver could control this and we could - * remove "output-high" here. - */ - output-high; /* TODO: Remove this? */ - }; + /* + * The pen driver doesn't currently support + * driving this reset line. By specifying + * output-high here we're relying on the fact + * that this pin has a default pulldown at boot + * (which makes sure the pen was in reset if it + * was powered) and then we set it high here to + * take it out of reset. Better would be if the + * pen driver could control this and we could + * remove "output-high" here. + */ + output-high; /* TODO: Remove this? */ }; - p_sensor_int_l: p-sensor-int-l { - pinmux { - pins = "gpio24"; - function = "gpio"; - input-enable; - }; + p_sensor_int_l: p-sensor-int-l-state { + pins = "gpio24"; + function = "gpio"; + input-enable; - pinconf { - pins = "gpio24"; - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; - qup_uart3_sleep: qup-uart3-sleep { - pinmux { - pins = "gpio38", "gpio39", - "gpio40", "gpio41"; - function = "gpio"; - }; - - pinconf-cts { + qup_uart3_sleep: qup-uart3-sleep-state { + cts-pins { /* * Configure a pull-down on CTS to match the pull of * the Bluetooth module. */ pins = "gpio38"; + function = "gpio"; bias-pull-down; }; - pinconf-rts { + rts-pins { /* * Configure pull-down on RTS. As RTS is active low * signal, pull it low to indicate the BT SoC that it * can wakeup the system anytime from suspend state by * pulling RX low (by sending wakeup bytes). */ - pins = "gpio39"; - bias-pull-down; + pins = "gpio39"; + function = "gpio"; + bias-pull-down; }; - pinconf-tx { + tx-pins { /* * Configure pull-up on TX when it isn't actively driven * to prevent BT SoC from receiving garbage during sleep. */ pins = "gpio40"; + function = "gpio"; bias-pull-up; }; - pinconf-rx { + rx-pins { /* * Configure a pull-up on RX. This is needed to avoid * garbage data when the TX pin of the Bluetooth module * is floating which may cause spurious wakeups. */ pins = "gpio41"; + function = "gpio"; bias-pull-up; }; }; /* Named trackpad_int_1v8_odl on earlier revision schematics */ trackpad_int_1v8_odl: - tp_int_odl: tp-int-odl { - pinmux { - pins = "gpio0"; - function = "gpio"; - }; - - pinconf { - pins = "gpio0"; + tp_int_odl: tp-int-odl-state { + pins = "gpio0"; + function = "gpio"; - /* Has external pullup */ - bias-disable; - }; + /* Has external pullup */ + bias-disable; }; - ts_int_l: ts-int-l { - pinmux { - pins = "gpio9"; - function = "gpio"; - }; - - pinconf { - pins = "gpio9"; - bias-pull-up; - }; + ts_int_l: ts-int-l-state { + pins = "gpio9"; + function = "gpio"; + bias-pull-up; }; - ts_reset_l: ts-reset-l { - pinmux { - pins = "gpio8"; - function = "gpio"; - }; - - pinconf { - pins = "gpio8"; - bias-disable; - drive-strength = <2>; - }; + ts_reset_l: ts-reset-l-state { + pins = "gpio8"; + function = "gpio"; + bias-disable; + drive-strength = <2>; }; - sdc1_on: sdc1-on { - pinconf-clk { + sdc1_on: sdc1-on-state { + clk-pins { pins = "sdc1_clk"; bias-disable; drive-strength = <16>; }; - pinconf-cmd { + cmd-pins { pins = "sdc1_cmd"; bias-pull-up; drive-strength = <16>; }; - pinconf-data { + data-pins { pins = "sdc1_data"; bias-pull-up; drive-strength = <16>; }; - pinconf-rclk { + rclk-pins { pins = "sdc1_rclk"; bias-pull-down; }; }; - sdc1_off: sdc1-off { - pinconf-clk { + sdc1_off: sdc1-off-state { + clk-pins { pins = "sdc1_clk"; bias-disable; drive-strength = <2>; }; - pinconf-cmd { + cmd-pins { pins = "sdc1_cmd"; bias-pull-up; drive-strength = <2>; }; - pinconf-data { + data-pins { pins = "sdc1_data"; bias-pull-up; drive-strength = <2>; }; - pinconf-rclk { + rclk-pins { pins = "sdc1_rclk"; bias-pull-down; }; }; - sdc2_on: sdc2-on { - pinconf-clk { + sdc2_on: sdc2-on-state { + clk-pins { pins = "sdc2_clk"; bias-disable; drive-strength = <16>; }; - pinconf-cmd { + cmd-pins { pins = "sdc2_cmd"; bias-pull-up; drive-strength = <10>; }; - pinconf-data { + data-pins { pins = "sdc2_data"; bias-pull-up; drive-strength = <10>; }; - pinconf-sd-cd { + sd-cd-pins { pins = "gpio69"; + function = "gpio"; bias-pull-up; drive-strength = <2>; }; }; - sdc2_off: sdc2-off { - pinconf-clk { + sdc2_off: sdc2-off-state { + clk-pins { pins = "sdc2_clk"; bias-disable; drive-strength = <2>; }; - pinconf-cmd { + cmd-pins { pins = "sdc2_cmd"; bias-pull-up; drive-strength = <2>; }; - pinconf-data { + data-pins { pins = "sdc2_data"; bias-pull-up; drive-strength = <2>; }; - pinconf-sd-cd { + sd-cd-pins { pins = "gpio69"; + function = "gpio"; bias-pull-up; drive-strength = <2>; }; }; - uf_cam_en: uf-cam-en { - pinmux { - pins = "gpio6"; - function = "gpio"; - }; + uf_cam_en: uf-cam-en-state { + pins = "gpio6"; + function = "gpio"; + drive-strength = <2>; - pinconf { - pins = "gpio6"; - drive-strength = <2>; - /* External pull down */ - bias-disable; - }; + /* External pull down */ + bias-disable; }; - wf_cam_en: wf-cam-en { - pinmux { - pins = "gpio7"; - function = "gpio"; - }; + wf_cam_en: wf-cam-en-state { + pins = "gpio7"; + function = "gpio"; + drive-strength = <2>; - pinconf { - pins = "gpio7"; - drive-strength = <2>; - /* External pull down */ - bias-disable; - }; + /* External pull down */ + bias-disable; }; }; diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi index f1482675610a..ea886cf08b4d 100644 --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi @@ -796,7 +796,7 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; pinctrl-names = "default"; - pinctrl-0 = <&qup_spi0_default>; + pinctrl-0 = <&qup_spi0_spi>, <&qup_spi0_cs>; interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -850,7 +850,7 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; pinctrl-names = "default"; - pinctrl-0 = <&qup_spi1_default>; + pinctrl-0 = <&qup_spi1_spi>, <&qup_spi1_cs>; interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -940,7 +940,7 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; pinctrl-names = "default"; - pinctrl-0 = <&qup_spi3_default>; + pinctrl-0 = <&qup_spi3_spi>, <&qup_spi3_cs>; interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -1030,7 +1030,7 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; pinctrl-names = "default"; - pinctrl-0 = <&qup_spi5_default>; + pinctrl-0 = <&qup_spi5_spi>, <&qup_spi5_cs>; interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -1097,7 +1097,7 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; pinctrl-names = "default"; - pinctrl-0 = <&qup_spi6_default>; + pinctrl-0 = <&qup_spi6_spi>, <&qup_spi6_cs>; interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -1187,7 +1187,7 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; pinctrl-names = "default"; - pinctrl-0 = <&qup_spi8_default>; + pinctrl-0 = <&qup_spi8_spi>, <&qup_spi8_cs>; interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -1277,7 +1277,7 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; pinctrl-names = "default"; - pinctrl-0 = <&qup_spi10_default>; + pinctrl-0 = <&qup_spi10_spi>, <&qup_spi10_cs>; interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -1331,7 +1331,7 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; pinctrl-names = "default"; - pinctrl-0 = <&qup_spi11_default>; + pinctrl-0 = <&qup_spi11_spi>, <&qup_spi11_cs>; interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -1487,410 +1487,443 @@ gpio-ranges = <&tlmm 0 0 120>; wakeup-parent = <&pdc>; - dp_hot_plug_det: dp-hot-plug-det { - pinmux { - pins = "gpio117"; - function = "dp_hot"; - }; + dp_hot_plug_det: dp-hot-plug-det-state { + pins = "gpio117"; + function = "dp_hot"; }; - qspi_clk: qspi-clk { - pinmux { - pins = "gpio63"; - function = "qspi_clk"; - }; + qspi_clk: qspi-clk-state { + pins = "gpio63"; + function = "qspi_clk"; }; - qspi_cs0: qspi-cs0 { - pinmux { - pins = "gpio68"; - function = "qspi_cs"; - }; + qspi_cs0: qspi-cs0-state { + pins = "gpio68"; + function = "qspi_cs"; }; - qspi_cs1: qspi-cs1 { - pinmux { - pins = "gpio72"; - function = "qspi_cs"; - }; + qspi_cs1: qspi-cs1-state { + pins = "gpio72"; + function = "qspi_cs"; }; - qspi_data01: qspi-data01 { - pinmux-data { - pins = "gpio64", "gpio65"; - function = "qspi_data"; - }; + qspi_data01: qspi-data01-state { + pins = "gpio64", "gpio65"; + function = "qspi_data"; }; - qspi_data12: qspi-data12 { - pinmux-data { - pins = "gpio66", "gpio67"; - function = "qspi_data"; - }; + qspi_data12: qspi-data12-state { + pins = "gpio66", "gpio67"; + function = "qspi_data"; }; - qup_i2c0_default: qup-i2c0-default { - pinmux { - pins = "gpio34", "gpio35"; - function = "qup00"; - }; + qup_i2c0_default: qup-i2c0-default-state { + pins = "gpio34", "gpio35"; + function = "qup00"; }; - qup_i2c1_default: qup-i2c1-default { - pinmux { - pins = "gpio0", "gpio1"; - function = "qup01"; - }; + qup_i2c1_default: qup-i2c1-default-state { + pins = "gpio0", "gpio1"; + function = "qup01"; }; - qup_i2c2_default: qup-i2c2-default { - pinmux { - pins = "gpio15", "gpio16"; - function = "qup02_i2c"; - }; + qup_i2c2_default: qup-i2c2-default-state { + pins = "gpio15", "gpio16"; + function = "qup02_i2c"; }; - qup_i2c3_default: qup-i2c3-default { - pinmux { - pins = "gpio38", "gpio39"; - function = "qup03"; - }; + qup_i2c3_default: qup-i2c3-default-state { + pins = "gpio38", "gpio39"; + function = "qup03"; }; - qup_i2c4_default: qup-i2c4-default { - pinmux { - pins = "gpio115", "gpio116"; - function = "qup04_i2c"; - }; + qup_i2c4_default: qup-i2c4-default-state { + pins = "gpio115", "gpio116"; + function = "qup04_i2c"; }; - qup_i2c5_default: qup-i2c5-default { - pinmux { - pins = "gpio25", "gpio26"; - function = "qup05"; - }; + qup_i2c5_default: qup-i2c5-default-state { + pins = "gpio25", "gpio26"; + function = "qup05"; }; - qup_i2c6_default: qup-i2c6-default { - pinmux { - pins = "gpio59", "gpio60"; - function = "qup10"; - }; + qup_i2c6_default: qup-i2c6-default-state { + pins = "gpio59", "gpio60"; + function = "qup10"; }; - qup_i2c7_default: qup-i2c7-default { - pinmux { - pins = "gpio6", "gpio7"; - function = "qup11_i2c"; - }; + qup_i2c7_default: qup-i2c7-default-state { + pins = "gpio6", "gpio7"; + function = "qup11_i2c"; }; - qup_i2c8_default: qup-i2c8-default { - pinmux { - pins = "gpio42", "gpio43"; - function = "qup12"; - }; + qup_i2c8_default: qup-i2c8-default-state { + pins = "gpio42", "gpio43"; + function = "qup12"; }; - qup_i2c9_default: qup-i2c9-default { - pinmux { - pins = "gpio46", "gpio47"; - function = "qup13_i2c"; - }; + qup_i2c9_default: qup-i2c9-default-state { + pins = "gpio46", "gpio47"; + function = "qup13_i2c"; }; - qup_i2c10_default: qup-i2c10-default { - pinmux { - pins = "gpio86", "gpio87"; - function = "qup14"; - }; + qup_i2c10_default: qup-i2c10-default-state { + pins = "gpio86", "gpio87"; + function = "qup14"; }; - qup_i2c11_default: qup-i2c11-default { - pinmux { - pins = "gpio53", "gpio54"; - function = "qup15"; - }; + qup_i2c11_default: qup-i2c11-default-state { + pins = "gpio53", "gpio54"; + function = "qup15"; + }; + + qup_spi0_spi: qup-spi0-spi-state { + pins = "gpio34", "gpio35", "gpio36"; + function = "qup00"; + }; + + qup_spi0_cs: qup-spi0-cs-state { + pins = "gpio37"; + function = "qup00"; + }; + + qup_spi0_cs_gpio: qup-spi0-cs-gpio-state { + pins = "gpio37"; + function = "gpio"; + }; + + qup_spi1_spi: qup-spi1-spi-state { + pins = "gpio0", "gpio1", "gpio2"; + function = "qup01"; + }; + + qup_spi1_cs: qup-spi1-cs-state { + pins = "gpio3"; + function = "qup01"; + }; + + qup_spi1_cs_gpio: qup-spi1-cs-gpio-state { + pins = "gpio3"; + function = "gpio"; + }; + + qup_spi3_spi: qup-spi3-spi-state { + pins = "gpio38", "gpio39", "gpio40"; + function = "qup03"; + }; + + qup_spi3_cs: qup-spi3-cs-state { + pins = "gpio41"; + function = "qup03"; }; - qup_spi0_default: qup-spi0-default { - pinmux { - pins = "gpio34", "gpio35", - "gpio36", "gpio37"; + qup_spi3_cs_gpio: qup-spi3-cs-gpio-state { + pins = "gpio41"; + function = "gpio"; + }; + + qup_spi5_spi: qup-spi5-spi-state { + pins = "gpio25", "gpio26", "gpio27"; + function = "qup05"; + }; + + qup_spi5_cs: qup-spi5-cs-state { + pins = "gpio28"; + function = "qup05"; + }; + + qup_spi5_cs_gpio: qup-spi5-cs-gpio-state { + pins = "gpio28"; + function = "gpio"; + }; + + qup_spi6_spi: qup-spi6-spi-state { + pins = "gpio59", "gpio60", "gpio61"; + function = "qup10"; + }; + + qup_spi6_cs: qup-spi6-cs-state { + pins = "gpio62"; + function = "qup10"; + }; + + qup_spi6_cs_gpio: qup-spi6-cs-gpio-state { + pins = "gpio62"; + function = "gpio"; + }; + + qup_spi8_spi: qup-spi8-spi-state { + pins = "gpio42", "gpio43", "gpio44"; + function = "qup12"; + }; + + qup_spi8_cs: qup-spi8-cs-state { + pins = "gpio45"; + function = "qup12"; + }; + + qup_spi8_cs_gpio: qup-spi8-cs-gpio-state { + pins = "gpio45"; + function = "gpio"; + }; + + qup_spi10_spi: qup-spi10-spi-state { + pins = "gpio86", "gpio87", "gpio88"; + function = "qup14"; + }; + + qup_spi10_cs: qup-spi10-cs-state { + pins = "gpio89"; + function = "qup14"; + }; + + qup_spi10_cs_gpio: qup-spi10-cs-gpio-state { + pins = "gpio89"; + function = "gpio"; + }; + + qup_spi11_spi: qup-spi11-spi-state { + pins = "gpio53", "gpio54", "gpio55"; + function = "qup15"; + }; + + qup_spi11_cs: qup-spi11-cs-state { + pins = "gpio56"; + function = "qup15"; + }; + + qup_spi11_cs_gpio: qup-spi11-cs-gpio-state { + pins = "gpio56"; + function = "gpio"; + }; + + qup_uart0_default: qup-uart0-default-state { + qup_uart0_cts: cts-pins { + pins = "gpio34"; function = "qup00"; }; - }; - qup_spi0_cs_gpio: qup-spi0-cs-gpio { - pinmux { - pins = "gpio34", "gpio35", - "gpio36"; + qup_uart0_rts: rts-pins { + pins = "gpio35"; function = "qup00"; }; - pinmux-cs { + qup_uart0_tx: tx-pins { + pins = "gpio36"; + function = "qup00"; + }; + + qup_uart0_rx: rx-pins { pins = "gpio37"; - function = "gpio"; + function = "qup00"; }; }; - qup_spi1_default: qup-spi1-default { - pinmux { - pins = "gpio0", "gpio1", - "gpio2", "gpio3"; + qup_uart1_default: qup-uart1-default-state { + qup_uart1_cts: cts-pins { + pins = "gpio0"; function = "qup01"; }; - }; - qup_spi1_cs_gpio: qup-spi1-cs-gpio { - pinmux { - pins = "gpio0", "gpio1", - "gpio2"; + qup_uart1_rts: rts-pins { + pins = "gpio1"; function = "qup01"; }; - pinmux-cs { - pins = "gpio3"; - function = "gpio"; + qup_uart1_tx: tx-pins { + pins = "gpio2"; + function = "qup01"; }; - }; - qup_spi3_default: qup-spi3-default { - pinmux { - pins = "gpio38", "gpio39", - "gpio40", "gpio41"; - function = "qup03"; + qup_uart1_rx: rx-pins { + pins = "gpio3"; + function = "qup01"; }; }; - qup_spi3_cs_gpio: qup-spi3-cs-gpio { - pinmux { - pins = "gpio38", "gpio39", - "gpio40"; - function = "qup03"; + qup_uart2_default: qup-uart2-default-state { + qup_uart2_tx: tx-pins { + pins = "gpio15"; + function = "qup02_uart"; }; - pinmux-cs { - pins = "gpio41"; - function = "gpio"; + qup_uart2_rx: rx-pins { + pins = "gpio16"; + function = "qup02_uart"; }; }; - qup_spi5_default: qup-spi5-default { - pinmux { - pins = "gpio25", "gpio26", - "gpio27", "gpio28"; - function = "qup05"; + qup_uart3_default: qup-uart3-default-state { + qup_uart3_cts: cts-pins { + pins = "gpio38"; + function = "qup03"; }; - }; - qup_spi5_cs_gpio: qup-spi5-cs-gpio { - pinmux { - pins = "gpio25", "gpio26", - "gpio27"; - function = "qup05"; + qup_uart3_rts: rts-pins { + pins = "gpio39"; + function = "qup03"; }; - pinmux-cs { - pins = "gpio28"; - function = "gpio"; + qup_uart3_tx: tx-pins { + pins = "gpio40"; + function = "qup03"; }; - }; - qup_spi6_default: qup-spi6-default { - pinmux { - pins = "gpio59", "gpio60", - "gpio61", "gpio62"; - function = "qup10"; + qup_uart3_rx: rx-pins { + pins = "gpio41"; + function = "qup03"; }; }; - qup_spi6_cs_gpio: qup-spi6-cs-gpio { - pinmux { - pins = "gpio59", "gpio60", - "gpio61"; - function = "qup10"; + qup_uart4_default: qup-uart4-default-state { + qup_uart4_tx: tx-pins { + pins = "gpio115"; + function = "qup04_uart"; }; - pinmux-cs { - pins = "gpio62"; - function = "gpio"; + qup_uart4_rx: rx-pins { + pins = "gpio116"; + function = "qup04_uart"; }; }; - qup_spi8_default: qup-spi8-default { - pinmux { - pins = "gpio42", "gpio43", - "gpio44", "gpio45"; - function = "qup12"; + qup_uart5_default: qup-uart5-default-state { + qup_uart5_cts: cts-pins { + pins = "gpio25"; + function = "qup05"; }; - }; - qup_spi8_cs_gpio: qup-spi8-cs-gpio { - pinmux { - pins = "gpio42", "gpio43", - "gpio44"; - function = "qup12"; + qup_uart5_rts: rts-pins { + pins = "gpio26"; + function = "qup05"; }; - pinmux-cs { - pins = "gpio45"; - function = "gpio"; + qup_uart5_tx: tx-pins { + pins = "gpio27"; + function = "qup05"; }; - }; - qup_spi10_default: qup-spi10-default { - pinmux { - pins = "gpio86", "gpio87", - "gpio88", "gpio89"; - function = "qup14"; + qup_uart5_rx: rx-pins { + pins = "gpio28"; + function = "qup05"; }; }; - qup_spi10_cs_gpio: qup-spi10-cs-gpio { - pinmux { - pins = "gpio86", "gpio87", - "gpio88"; - function = "qup14"; + qup_uart6_default: qup-uart6-default-state { + qup_uart6_cts: cts-pins { + pins = "gpio59"; + function = "qup10"; }; - pinmux-cs { - pins = "gpio89"; - function = "gpio"; + qup_uart6_rts: rts-pins { + pins = "gpio60"; + function = "qup10"; }; - }; - qup_spi11_default: qup-spi11-default { - pinmux { - pins = "gpio53", "gpio54", - "gpio55", "gpio56"; - function = "qup15"; + qup_uart6_tx: tx-pins { + pins = "gpio61"; + function = "qup10"; + }; + + qup_uart6_rx: rx-pins { + pins = "gpio62"; + function = "qup10"; }; }; - qup_spi11_cs_gpio: qup-spi11-cs-gpio { - pinmux { - pins = "gpio53", "gpio54", - "gpio55"; - function = "qup15"; + qup_uart7_default: qup-uart7-default-state { + qup_uart7_tx: tx-pins { + pins = "gpio6"; + function = "qup11_uart"; }; - pinmux-cs { - pins = "gpio56"; - function = "gpio"; + qup_uart7_rx: rx-pins { + pins = "gpio7"; + function = "qup11_uart"; }; }; - qup_uart0_default: qup-uart0-default { - pinmux { - pins = "gpio34", "gpio35", - "gpio36", "gpio37"; - function = "qup00"; + qup_uart8_default: qup-uart8-default-state { + qup_uart8_tx: tx-pins { + pins = "gpio44"; + function = "qup12"; }; - }; - qup_uart1_default: qup-uart1-default { - pinmux { - pins = "gpio0", "gpio1", - "gpio2", "gpio3"; - function = "qup01"; + qup_uart8_rx: rx-pins { + pins = "gpio45"; + function = "qup12"; }; }; - qup_uart2_default: qup-uart2-default { - pinmux { - pins = "gpio15", "gpio16"; - function = "qup02_uart"; + qup_uart9_default: qup-uart9-default-state { + qup_uart9_tx: tx-pins { + pins = "gpio46"; + function = "qup13_uart"; }; - }; - qup_uart3_default: qup-uart3-default { - pinmux { - pins = "gpio38", "gpio39", - "gpio40", "gpio41"; - function = "qup03"; + qup_uart9_rx: rx-pins { + pins = "gpio47"; + function = "qup13_uart"; }; }; - qup_uart4_default: qup-uart4-default { - pinmux { - pins = "gpio115", "gpio116"; - function = "qup04_uart"; + qup_uart10_default: qup-uart10-default-state { + qup_uart10_cts: cts-pins { + pins = "gpio86"; + function = "qup14"; }; - }; - qup_uart5_default: qup-uart5-default { - pinmux { - pins = "gpio25", "gpio26", - "gpio27", "gpio28"; - function = "qup05"; + qup_uart10_rts: rts-pins { + pins = "gpio87"; + function = "qup14"; }; - }; - qup_uart6_default: qup-uart6-default { - pinmux { - pins = "gpio59", "gpio60", - "gpio61", "gpio62"; - function = "qup10"; + qup_uart10_tx: tx-pins { + pins = "gpio88"; + function = "qup14"; }; - }; - qup_uart7_default: qup-uart7-default { - pinmux { - pins = "gpio6", "gpio7"; - function = "qup11_uart"; + qup_uart10_rx: rx-pins { + pins = "gpio89"; + function = "qup14"; }; }; - qup_uart8_default: qup-uart8-default { - pinmux { - pins = "gpio44", "gpio45"; - function = "qup12"; + qup_uart11_default: qup-uart11-default-state { + qup_uart11_cts: cts-pins { + pins = "gpio53"; + function = "qup15"; }; - }; - qup_uart9_default: qup-uart9-default { - pinmux { - pins = "gpio46", "gpio47"; - function = "qup13_uart"; + qup_uart11_rts: rts-pins { + pins = "gpio54"; + function = "qup15"; }; - }; - qup_uart10_default: qup-uart10-default { - pinmux { - pins = "gpio86", "gpio87", - "gpio88", "gpio89"; - function = "qup14"; + qup_uart11_tx: tx-pins { + pins = "gpio55"; + function = "qup15"; }; - }; - qup_uart11_default: qup-uart11-default { - pinmux { - pins = "gpio53", "gpio54", - "gpio55", "gpio56"; + qup_uart11_rx: rx-pins { + pins = "gpio56"; function = "qup15"; }; }; - sec_mi2s_active: sec-mi2s-active { - pinmux { - pins = "gpio49", "gpio50", "gpio51"; - function = "mi2s_1"; - }; + sec_mi2s_active: sec-mi2s-active-state { + pins = "gpio49", "gpio50", "gpio51"; + function = "mi2s_1"; }; - pri_mi2s_active: pri-mi2s-active { - pinmux { - pins = "gpio53", "gpio54", "gpio55", "gpio56"; - function = "mi2s_0"; - }; + pri_mi2s_active: pri-mi2s-active-state { + pins = "gpio53", "gpio54", "gpio55", "gpio56"; + function = "mi2s_0"; }; - pri_mi2s_mclk_active: pri-mi2s-mclk-active { - pinmux { - pins = "gpio57"; - function = "lpass_ext"; - }; + pri_mi2s_mclk_active: pri-mi2s-mclk-active-state { + pins = "gpio57"; + function = "lpass_ext"; }; }; |