diff options
Diffstat (limited to 'arch/arm/mach-ux500/board-mop500-pins.c')
-rw-r--r-- | arch/arm/mach-ux500/board-mop500-pins.c | 53 |
1 files changed, 0 insertions, 53 deletions
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c index 6cc71d02957f..71ee944ea70f 100644 --- a/arch/arm/mach-ux500/board-mop500-pins.c +++ b/arch/arm/mach-ux500/board-mop500-pins.c @@ -27,7 +27,6 @@ BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0)); /* These also force them into GPIO mode */ BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED); -BIAS(gpio_in_pd, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED); BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED); BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED); @@ -299,56 +298,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = { AB8505_PIN_HOG("GPIO53_D15", in_pd), }; -/* - * The HREFv60 series of platforms is using available pins on the DB8500 - * insteaf of the Toshiba I2C GPIO expander, reusing some pins like the SSP0 - * and SSP1 ports (previously connected to the AB8500) as generic GPIO lines. - */ -static struct pinctrl_map __initdata hrefv60_pinmap[] = { - /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */ - DB8500_PIN_HOG("GPIO31_V3", gpio_in_pu), /* EN1 */ - DB8500_PIN_HOG("GPIO32_V2", gpio_in_pd), /* DRDY */ - /* - * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and - * GPIO 67 for interrupts. Pull-up the IRQ line and drive both - * reset signals low. - */ - DB8500_PIN_HOG("GPIO143_D12", gpio_out_lo), /* TOUCH_RST1 */ - DB8500_PIN_HOG("GPIO67_G2", gpio_in_pu), /* TOUCH_INT2 */ - DB8500_PIN_HOG("GPIO146_D13", gpio_out_lo), /* TOUCH_RST2 */ - /* - * Drive D19-D23 for the ETM PTM trace interface low, - * (presumably pins are unconnected therefore grounded here, - * the "other alt C1" setting enables these pins) - */ - DB8500_PIN_HOG("GPIO70_G5", gpio_out_lo), - DB8500_PIN_HOG("GPIO71_G4", gpio_out_lo), - DB8500_PIN_HOG("GPIO72_H4", gpio_out_lo), - DB8500_PIN_HOG("GPIO73_H3", gpio_out_lo), - DB8500_PIN_HOG("GPIO74_J3", gpio_out_lo), - /* NAHJ CTRL on GPIO 76 to low, CTRL_INV on GPIO216 to high */ - DB8500_PIN_HOG("GPIO76_J2", gpio_out_lo), /* CTRL */ - DB8500_PIN_HOG("GPIO216_AG12", gpio_out_hi), /* CTRL_INV */ - /* NFC ENA and RESET to low, pulldown IRQ line */ - DB8500_PIN_HOG("GPIO77_H1", gpio_out_lo), /* NFC_ENA */ - DB8500_PIN_HOG("GPIO144_B13", gpio_in_pd), /* NFC_IRQ */ - DB8500_PIN_HOG("GPIO142_C11", gpio_out_lo), /* NFC_RESET */ - DB8500_PIN_HOG("GPIO91_B6", gpio_in_pu), /* FORCE_SENSING_INT */ - DB8500_PIN_HOG("GPIO92_D6", gpio_out_lo), /* FORCE_SENSING_RST */ - DB8500_PIN_HOG("GPIO97_D9", gpio_out_lo), /* FORCE_SENSING_WU */ - /* DiPro Sensor interrupt */ - DB8500_PIN_HOG("GPIO139_C9", gpio_in_pu), /* DIPRO_INT */ - /* Audio Amplifier HF enable */ - DB8500_PIN_HOG("GPIO149_B14", gpio_out_hi), /* VAUDIO_HF_EN, enable MAX8968 */ - /* GBF interface, pull low to reset state */ - DB8500_PIN_HOG("GPIO171_D23", gpio_out_lo), /* GBF_ENA_RESET */ - /* MSP : HDTV INTERFACE GPIO line */ - DB8500_PIN_HOG("GPIO192_AJ27", gpio_in_pd), - /* Accelerometer interrupt lines */ - DB8500_PIN_HOG("GPIO82_C1", gpio_in_pu), /* ACC_INT1 */ - DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */ -}; - static struct pinctrl_map __initdata snowball_pinmap[] = { /* Mux in SSP0 connected to AB8500, pull down RXD pin */ DB8500_MUX_HOG("ssp0_a_1", "ssp0"), @@ -390,8 +339,6 @@ void __init snowball_pinmaps_init(void) void __init hrefv60_pinmaps_init(void) { - pinctrl_register_mappings(hrefv60_pinmap, - ARRAY_SIZE(hrefv60_pinmap)); pinctrl_register_mappings(ab8500_pinmap, ARRAY_SIZE(ab8500_pinmap)); } |