diff options
Diffstat (limited to 'arch/arm/mach-at91/include/mach/board.h')
| -rw-r--r-- | arch/arm/mach-at91/include/mach/board.h | 42 |
1 files changed, 16 insertions, 26 deletions
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h index eac92e995bb5..d0b377b21bd7 100644 --- a/arch/arm/mach-at91/include/mach/board.h +++ b/arch/arm/mach-at91/include/mach/board.h @@ -40,13 +40,14 @@ #include <linux/atmel-mci.h> #include <sound/atmel-ac97c.h> #include <linux/serial.h> +#include <linux/platform_data/macb.h> /* USB Device */ struct at91_udc_data { - u8 vbus_pin; /* high == host powering us */ + int vbus_pin; /* high == host powering us */ u8 vbus_active_low; /* vbus polarity */ u8 vbus_polled; /* Use polling, not interrupt */ - u8 pullup_pin; /* active == D+ pulled up */ + int pullup_pin; /* active == D+ pulled up */ u8 pullup_active_low; /* true == pullup_pin is active low */ }; extern void __init at91_add_device_udc(struct at91_udc_data *data); @@ -56,10 +57,10 @@ extern void __init at91_add_device_usba(struct usba_platform_data *data); /* Compact Flash */ struct at91_cf_data { - u8 irq_pin; /* I/O IRQ */ - u8 det_pin; /* Card detect */ - u8 vcc_pin; /* power switching */ - u8 rst_pin; /* card reset */ + int irq_pin; /* I/O IRQ */ + int det_pin; /* Card detect */ + int vcc_pin; /* power switching */ + int rst_pin; /* card reset */ u8 chipselect; /* EBI Chip Select number */ u8 flags; #define AT91_CF_TRUE_IDE 0x01 @@ -70,37 +71,26 @@ extern void __init at91_add_device_cf(struct at91_cf_data *data); /* MMC / SD */ /* at91_mci platform config */ struct at91_mmc_data { - u8 det_pin; /* card detect IRQ */ + int det_pin; /* card detect IRQ */ unsigned slot_b:1; /* uses Slot B */ unsigned wire4:1; /* (SD) supports DAT0..DAT3 */ - u8 wp_pin; /* (SD) writeprotect detect */ - u8 vcc_pin; /* power switching (high == on) */ + int wp_pin; /* (SD) writeprotect detect */ + int vcc_pin; /* power switching (high == on) */ }; extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data); /* atmel-mci platform config */ extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data); - /* Ethernet (EMAC & MACB) */ -struct at91_eth_data { - u32 phy_mask; - u8 phy_irq_pin; /* PHY IRQ */ - u8 is_rmii; /* using RMII interface? */ -}; -extern void __init at91_add_device_eth(struct at91_eth_data *data); - -#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) \ - || defined(CONFIG_ARCH_AT91SAM9G45) -#define eth_platform_data at91_eth_data -#endif +extern void __init at91_add_device_eth(struct macb_platform_data *data); /* USB Host */ struct at91_usbh_data { u8 ports; /* number of ports on root hub */ - u8 vbus_pin[2]; /* port power-control pin */ + int vbus_pin[2]; /* port power-control pin */ u8 vbus_pin_inverted; u8 overcurrent_supported; - u8 overcurrent_pin[2]; + int overcurrent_pin[2]; u8 overcurrent_status[2]; u8 overcurrent_changed[2]; }; @@ -110,9 +100,9 @@ extern void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data); /* NAND / SmartMedia */ struct atmel_nand_data { - u8 enable_pin; /* chip enable */ - u8 det_pin; /* card detect */ - u8 rdy_pin; /* ready/busy */ + int enable_pin; /* chip enable */ + int det_pin; /* card detect */ + int rdy_pin; /* ready/busy */ u8 rdy_pin_active_low; /* rdy_pin value is inverted */ u8 ale; /* address line number connected to ALE */ u8 cle; /* address line number connected to CLE */ |