diff options
Diffstat (limited to 'arch/arm/boot/dts/stm32mp135f-dk.dts')
| -rw-r--r-- | arch/arm/boot/dts/stm32mp135f-dk.dts | 144 |
1 files changed, 143 insertions, 1 deletions
diff --git a/arch/arm/boot/dts/stm32mp135f-dk.dts b/arch/arm/boot/dts/stm32mp135f-dk.dts index de341d17e87d..9ff5a3eaf55b 100644 --- a/arch/arm/boot/dts/stm32mp135f-dk.dts +++ b/arch/arm/boot/dts/stm32mp135f-dk.dts @@ -59,6 +59,22 @@ }; }; + v3v3_sw: v3v3-sw { + compatible = "regulator-fixed"; + regulator-name = "v3v3_sw"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_adc: vdd-adc { + compatible = "regulator-fixed"; + regulator-name = "vdd_adc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + vdd_sd: vdd-sd { compatible = "regulator-fixed"; regulator-name = "vdd_sd"; @@ -66,6 +82,39 @@ regulator-max-microvolt = <2900000>; regulator-always-on; }; + + vdd_usb: vdd-usb { + compatible = "regulator-fixed"; + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; +}; + +&adc_1 { + pinctrl-names = "default"; + pinctrl-0 = <&adc1_usb_cc_pins_a>; + vdda-supply = <&vdd_adc>; + vref-supply = <&vdd_adc>; + status = "okay"; + adc1: adc@0 { + status = "okay"; + /* + * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in6 & in12. + * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C: + * 5 * (5.1 + 47kOhms) * 5pF => 1.3us. + * Use arbitrary margin here (e.g. 5us). + */ + channel@6 { + reg = <6>; + st,min-sample-time-ns = <5000>; + }; + channel@12 { + reg = <12>; + st,min-sample-time-ns = <5000>; + }; + }; }; &i2c1 { @@ -79,6 +128,42 @@ /* spare dmas for other usage */ /delete-property/dmas; /delete-property/dma-names; + + mcp23017: pinctrl@21 { + compatible = "microchip,mcp23017"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <12 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&gpiog>; + pinctrl-names = "default"; + pinctrl-0 = <&mcp23017_pins_a>; + interrupt-controller; + #interrupt-cells = <2>; + microchip,irq-mirror; + }; + + typec@53 { + compatible = "st,stm32g0-typec"; + reg = <0x53>; + /* Alert pin on PI2 */ + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpioi>; + /* Internal pull-up on PI2 */ + pinctrl-names = "default"; + pinctrl-0 = <&stm32g0_intn_pins_a>; + firmware-name = "stm32g0-ucsi.mp135f-dk.fw"; + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + + port { + con_usb_c_g0_ep: endpoint { + remote-endpoint = <&usbotg_hs_ep>; + }; + }; + }; + }; }; &i2c5 { @@ -108,7 +193,7 @@ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>; pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>; pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; - broken-cd; + cd-gpios = <&gpioh 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; disable-wp; st,neg-edge; bus-width = <4>; @@ -128,3 +213,60 @@ pinctrl-0 = <&uart4_pins_a>; status = "okay"; }; + +&usbh_ehci { + phys = <&usbphyc_port0>; + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + /* onboard HUB */ + hub@1 { + compatible = "usb424,2514"; + reg = <1>; + vdd-supply = <&v3v3_sw>; + }; +}; + +&usbotg_hs { + phys = <&usbphyc_port1 0>; + phy-names = "usb2-phy"; + usb-role-switch; + status = "okay"; + port { + usbotg_hs_ep: endpoint { + remote-endpoint = <&con_usb_c_g0_ep>; + }; + }; +}; + +&usbphyc { + status = "okay"; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; + st,current-boost-microamp = <1000>; + st,decrease-hs-slew-rate; + st,tune-hs-dc-level = <2>; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <11>; + st,trim-hs-impedance = <2>; + st,tune-squelch-level = <1>; + st,enable-hs-rx-gain-eq; + st,no-hs-ftime-ctrl; + st,no-lsfs-sc; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; + st,current-boost-microamp = <1000>; + st,decrease-hs-slew-rate; + st,tune-hs-dc-level = <2>; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <11>; + st,trim-hs-impedance = <2>; + st,tune-squelch-level = <1>; + st,enable-hs-rx-gain-eq; + st,no-hs-ftime-ctrl; + st,no-lsfs-sc; +}; |