diff options
Diffstat (limited to 'arch/arm/boot/dts/am57xx-beagle-x15.dts')
| -rw-r--r-- | arch/arm/boot/dts/am57xx-beagle-x15.dts | 49 |
1 files changed, 31 insertions, 18 deletions
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index 3a05b94f59ed..d55e3ea89fda 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -98,13 +98,6 @@ pinctrl-0 = <&extcon_usb1_pins>; }; - extcon_usb2: extcon_usb2 { - compatible = "linux,extcon-usb-gpio"; - id-gpio = <&gpio7 24 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&extcon_usb2_pins>; - }; - hdmi0: connector { compatible = "hdmi-connector"; label = "hdmi"; @@ -326,12 +319,6 @@ >; }; - extcon_usb2_pins: extcon_usb2_pins { - pinctrl-single,pins = < - 0x3e8 (PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_ctsn.gpio7_24 */ - >; - }; - tpd12s015_pins: pinmux_tpd12s015_pins { pinctrl-single,pins = < 0x3b0 (PIN_OUTPUT | MUX_MODE14) /* gpio7_10 CT_CP_HPD */ @@ -415,11 +402,12 @@ /* SMPS9 unused */ ldo1_reg: ldo1 { - /* VDD_SD */ + /* VDD_SD / VDDSHV8 */ regulator-name = "ldo1"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; + regulator-always-on; }; ldo2_reg: ldo2 { @@ -432,7 +420,7 @@ }; ldo3_reg: ldo3 { - /* VDDA_1V8_PHY */ + /* VDDA_1V8_PHYA */ regulator-name = "ldo3"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -440,6 +428,15 @@ regulator-boot-on; }; + ldo4_reg: ldo4 { + /* VDDA_1V8_PHYB */ + regulator-name = "ldo4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + ldo9_reg: ldo9 { /* VDD_RTC */ regulator-name = "ldo9"; @@ -495,6 +492,14 @@ gpio-controller; #gpio-cells = <2>; }; + + extcon_usb2: tps659038_usb { + compatible = "ti,palmas-usb-vid"; + ti,enable-vbus-detection; + ti,enable-id-detection; + id-gpios = <&gpio7 24 GPIO_ACTIVE_HIGH>; + }; + }; tmp102: tmp102@48 { @@ -517,7 +522,8 @@ mcp_rtc: rtc@6f { compatible = "microchip,mcp7941x"; reg = <0x6f>; - interrupts = <GIC_SPI 2 IRQ_TYPE_EDGE_RISING>; /* IRQ_SYS_1N */ + interrupts-extended = <&crossbar_mpu GIC_SPI 2 IRQ_TYPE_EDGE_RISING>, + <&dra7_pmx_core 0x424>; pinctrl-names = "default"; pinctrl-0 = <&mcp79410_pins_default>; @@ -579,7 +585,6 @@ pinctrl-0 = <&mmc1_pins_default>; vmmc-supply = <&ldo1_reg>; - vmmc_aux-supply = <&vdd_3v3>; bus-width = <4>; cd-gpios = <&gpio6 27 0>; /* gpio 219 */ }; @@ -623,6 +628,14 @@ }; &usb2 { + /* + * Stand alone usage is peripheral only. + * However, with some resistor modifications + * this port can be used via expansion connectors + * as "host" or "dual-role". If so, provide + * the necessary dr_mode override in the expansion + * board's DT. + */ dr_mode = "peripheral"; }; @@ -681,7 +694,7 @@ &hdmi { status = "ok"; - vdda-supply = <&ldo3_reg>; + vdda-supply = <&ldo4_reg>; pinctrl-names = "default"; pinctrl-0 = <&hdmi_pins>; |