diff options
Diffstat (limited to 'arch/arc/plat-arcfpga/platform.c')
| -rw-r--r-- | arch/arc/plat-arcfpga/platform.c | 226 |
1 files changed, 226 insertions, 0 deletions
diff --git a/arch/arc/plat-arcfpga/platform.c b/arch/arc/plat-arcfpga/platform.c new file mode 100644 index 000000000000..4e20a1a5104d --- /dev/null +++ b/arch/arc/plat-arcfpga/platform.c @@ -0,0 +1,226 @@ +/* + * ARC FPGA Platform support code + * + * Copyright (C) 2012 Synopsys, Inc. (www.synopsys.com) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/console.h> +#include <linux/of_platform.h> +#include <asm/setup.h> +#include <asm/clk.h> +#include <asm/mach_desc.h> +#include <plat/memmap.h> +#include <plat/smp.h> +#include <plat/irq.h> + +/*-----------------------BVCI Latency Unit -----------------------------*/ + +#ifdef CONFIG_ARC_HAS_BVCI_LAT_UNIT + +int lat_cycles = CONFIG_BVCI_LAT_CYCLES; + +/* BVCI Bus Profiler: Latency Unit */ +static void __init setup_bvci_lat_unit(void) +{ +#define MAX_BVCI_UNITS 12 + + unsigned int i; + unsigned int *base = (unsigned int *)BVCI_LAT_UNIT_BASE; + const unsigned long units_req = CONFIG_BVCI_LAT_UNITS; + const unsigned int REG_UNIT = 21; + const unsigned int REG_VAL = 22; + + /* + * There are multiple Latency Units corresponding to the many + * interfaces of the system bus arbiter (both CPU side as well as + * the peripheral side). + * + * Unit 0 - System Arb and Mem Controller - adds latency to all + * memory trasactions + * Unit 1 - I$ and System Bus + * Unit 2 - D$ and System Bus + * .. + * Unit 12 - IDE Disk controller and System Bus + * + * The programmers model requires writing to lat_unit reg first + * and then the latency value (cycles) to lat_value reg + */ + + if (CONFIG_BVCI_LAT_UNITS == 0) { + writel(0, base + REG_UNIT); + writel(lat_cycles, base + REG_VAL); + pr_info("BVCI Latency for all Memory Transactions %d cycles\n", + lat_cycles); + } else { + for_each_set_bit(i, &units_req, MAX_BVCI_UNITS) { + writel(i + 1, base + REG_UNIT); /* loop is 0 based */ + writel(lat_cycles, base + REG_VAL); + pr_info("BVCI Latency for Unit[%d] = %d cycles\n", + (i + 1), lat_cycles); + } + } +} +#else +static void __init setup_bvci_lat_unit(void) +{ +} +#endif + +/*----------------------- Platform Devices -----------------------------*/ + +static unsigned long arc_uart_info[] = { + 0, /* uart->is_emulated (runtime @running_on_hw) */ + 0, /* uart->port.uartclk */ + 0, /* uart->baud */ + 0 +}; + +#if defined(CONFIG_SERIAL_ARC_CONSOLE) +/* + * static platform data - but only for early serial + * TBD: derive this from a special DT node + */ +static struct resource arc_uart0_res[] = { + { + .start = UART0_BASE, + .end = UART0_BASE + 0xFF, + .flags = IORESOURCE_MEM, + }, + { + .start = UART0_IRQ, + .end = UART0_IRQ, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device arc_uart0_dev = { + .name = "arc-uart", + .id = 0, + .num_resources = ARRAY_SIZE(arc_uart0_res), + .resource = arc_uart0_res, + .dev = { + .platform_data = &arc_uart_info, + }, +}; + +static struct platform_device *fpga_early_devs[] __initdata = { + &arc_uart0_dev, +}; +#endif + +static void arc_fpga_serial_init(void) +{ + /* To let driver workaround ISS bug: baudh Reg can't be set to 0 */ + arc_uart_info[0] = !running_on_hw; + + arc_uart_info[1] = arc_get_core_freq(); + + arc_uart_info[2] = CONFIG_ARC_SERIAL_BAUD; + +#if defined(CONFIG_SERIAL_ARC_CONSOLE) + early_platform_add_devices(fpga_early_devs, + ARRAY_SIZE(fpga_early_devs)); + + /* + * ARC console driver registers itself as an early platform driver + * of class "earlyprintk". + * Install it here, followed by probe of devices. + * The installation here doesn't require earlyprintk in command line + * To do so however, replace the lines below with + * parse_early_param(); + * early_platform_driver_probe("earlyprintk", 1, 1); + * ^^ + */ + early_platform_driver_register_all("earlyprintk"); + early_platform_driver_probe("earlyprintk", 1, 0); + + /* + * This is to make sure that arc uart would be preferred console + * despite one/more of following: + * -command line lacked "console=ttyARC0" or + * -CONFIG_VT_CONSOLE was enabled (for no reason whatsoever) + * Note that this needs to be done after above early console is reg, + * otherwise the early console never gets a chance to run. + */ + add_preferred_console("ttyARC", 0, "115200"); +#endif +} + +static void __init plat_fpga_early_init(void) +{ + pr_info("[plat-arcfpga]: registering early dev resources\n"); + + setup_bvci_lat_unit(); + + arc_fpga_serial_init(); + +#ifdef CONFIG_SMP + iss_model_init_early_smp(); +#endif +} + +static struct of_dev_auxdata plat_auxdata_lookup[] __initdata = { +#if defined(CONFIG_SERIAL_ARC) || defined(CONFIG_SERIAL_ARC_MODULE) + OF_DEV_AUXDATA("snps,arc-uart", UART0_BASE, "arc-uart", arc_uart_info), +#endif + {} +}; + +static void __init plat_fpga_populate_dev(void) +{ + pr_info("[plat-arcfpga]: registering device resources\n"); + + /* + * Traverses flattened DeviceTree - registering platform devices + * complete with their resources + */ + of_platform_populate(NULL, of_default_bus_match_table, + plat_auxdata_lookup, NULL); +} + +/*----------------------- Machine Descriptions ------------------------------ + * + * Machine description is simply a set of platform/board specific callbacks + * This is not directly related to DeviceTree based dynamic device creation, + * however as part of early device tree scan, we also select the right + * callback set, by matching the DT compatible name. + */ + +static const char *aa4_compat[] __initdata = { + "snps,arc-angel4", + NULL, +}; + +MACHINE_START(ANGEL4, "angel4") + .dt_compat = aa4_compat, + .init_early = plat_fpga_early_init, + .init_machine = plat_fpga_populate_dev, + .init_irq = plat_fpga_init_IRQ, +#ifdef CONFIG_SMP + .init_smp = iss_model_init_smp, +#endif +MACHINE_END + +static const char *ml509_compat[] __initdata = { + "snps,arc-ml509", + NULL, +}; + +MACHINE_START(ML509, "ml509") + .dt_compat = ml509_compat, + .init_early = plat_fpga_early_init, + .init_machine = plat_fpga_populate_dev, + .init_irq = plat_fpga_init_IRQ, +#ifdef CONFIG_SMP + .init_smp = iss_model_init_smp, +#endif +MACHINE_END |