diff options
Diffstat (limited to 'Documentation')
5 files changed, 35 insertions, 5 deletions
diff --git a/Documentation/admin-guide/sysrq.rst b/Documentation/admin-guide/sysrq.rst index a46209f4636c..e6424d8c5846 100644 --- a/Documentation/admin-guide/sysrq.rst +++ b/Documentation/admin-guide/sysrq.rst @@ -231,13 +231,13 @@ prints help, and C) an action_msg string, that will print right before your handler is called. Your handler must conform to the prototype in 'sysrq.h'. After the ``sysrq_key_op`` is created, you can call the kernel function -``register_sysrq_key(int key, struct sysrq_key_op *op_p);`` this will +``register_sysrq_key(int key, const struct sysrq_key_op *op_p);`` this will register the operation pointed to by ``op_p`` at table key 'key', if that slot in the table is blank. At module unload time, you must call -the function ``unregister_sysrq_key(int key, struct sysrq_key_op *op_p)``, which -will remove the key op pointed to by 'op_p' from the key 'key', if and only if -it is currently registered in that slot. This is in case the slot has been -overwritten since you registered it. +the function ``unregister_sysrq_key(int key, const struct sysrq_key_op *op_p)``, +which will remove the key op pointed to by 'op_p' from the key 'key', if and +only if it is currently registered in that slot. This is in case the slot has +been overwritten since you registered it. The Magic SysRQ system works by registering key operations against a key op lookup table, which is defined in 'drivers/tty/sysrq.c'. This key table has diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt index c1091a923a89..0fa8e3e43bf8 100644 --- a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt +++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt @@ -21,6 +21,8 @@ Optional properties: the second cell is used to specify the GPIO polarity: 0 = active high, 1 = active low. +- irda-mode-ports: An array that lists the indices of the port that + should operate in IrDA mode. Example: sc16is750: sc16is750@51 { @@ -55,6 +57,8 @@ Optional properties: the second cell is used to specify the GPIO polarity: 0 = active high, 1 = active low. +- irda-mode-ports: An array that lists the indices of the port that + should operate in IrDA mode. Example: sc16is750: sc16is750@0 { diff --git a/Documentation/devicetree/bindings/serial/rs485.yaml b/Documentation/devicetree/bindings/serial/rs485.yaml index 8141e4aad530..fe90569475e1 100644 --- a/Documentation/devicetree/bindings/serial/rs485.yaml +++ b/Documentation/devicetree/bindings/serial/rs485.yaml @@ -41,4 +41,8 @@ properties: rs485-rx-during-tx: description: enables the receiving of data even while sending data. $ref: /schemas/types.yaml#/definitions/flag + + rs485-term-gpios: + description: GPIO pin to enable RS485 bus termination. + maxItems: 1 ... diff --git a/Documentation/devicetree/bindings/serial/samsung_uart.yaml b/Documentation/devicetree/bindings/serial/samsung_uart.yaml index ff2f49fe322c..32a5e1e30833 100644 --- a/Documentation/devicetree/bindings/serial/samsung_uart.yaml +++ b/Documentation/devicetree/bindings/serial/samsung_uart.yaml @@ -29,6 +29,14 @@ properties: reg: maxItems: 1 + reg-io-width: + description: | + The size (in bytes) of the IO accesses that should be performed + on the device. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 1, 4 ] + clocks: minItems: 2 maxItems: 5 diff --git a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml index 238c44192d31..75b8521eb7cb 100644 --- a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml +++ b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml @@ -48,6 +48,12 @@ properties: minItems: 1 maxItems: 2 + cts-gpios: + maxItems: 1 + + rts-gpios: + maxItems: 1 + wakeup-source: true rs485-rts-delay: true @@ -55,6 +61,14 @@ properties: linux,rs485-enabled-at-boot-time: true rs485-rx-during-tx: true +if: + required: + - st,hw-flow-ctrl +then: + properties: + cts-gpios: false + rts-gpios: false + required: - compatible - reg |