diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/extcon/extcon-arizona.txt | 60 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/extcon/extcon-max3355.txt | 21 |
2 files changed, 81 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/extcon/extcon-arizona.txt b/Documentation/devicetree/bindings/extcon/extcon-arizona.txt index e1705fae63a8..e27341f8a4c7 100644 --- a/Documentation/devicetree/bindings/extcon/extcon-arizona.txt +++ b/Documentation/devicetree/bindings/extcon/extcon-arizona.txt @@ -13,3 +13,63 @@ Optional properties: ARIZONA_ACCDET_MODE_HPR or 2 - Headphone detect mode is set to HPDETR If this node is not mentioned or if the value is unknown, then headphone detection mode is set to HPDETL. + + - wlf,use-jd2 : Use the additional JD input along with JD1 for dual pin jack + detection. + - wlf,use-jd2-nopull : Internal pull on JD2 is disabled when used for + jack detection. + - wlf,jd-invert : Invert the polarity of the jack detection switch + + - wlf,micd-software-compare : Use a software comparison to determine mic + presence + - wlf,micd-detect-debounce : Additional software microphone detection + debounce specified in milliseconds. + - wlf,micd-pol-gpio : GPIO specifier for the GPIO controlling the headset + polarity if one exists. + - wlf,micd-bias-start-time : Time allowed for MICBIAS to startup prior to + performing microphone detection, specified as per the ARIZONA_MICD_TIME_XXX + defines. + - wlf,micd-rate : Delay between successive microphone detection measurements, + specified as per the ARIZONA_MICD_TIME_XXX defines. + - wlf,micd-dbtime : Microphone detection hardware debounces specified as the + number of measurements to take, valid values being 2 and 4. + - wlf,micd-timeout-ms : Timeout for microphone detection, specified in + milliseconds. + - wlf,micd-force-micbias : Force MICBIAS continuously on during microphone + detection. + - wlf,micd-configs : Headset polarity configurations (generally used for + detection of CTIA / OMTP headsets), the field can be of variable length + but should always be a multiple of 3 cells long, each three cell group + represents one polarity configuration. + The first cell defines the accessory detection pin, zero will use MICDET1 + and all other values will use MICDET2. + The second cell represents the MICBIAS to be used. + The third cell represents the value of the micd-pol-gpio pin. + + - wlf,gpsw : Settings for the general purpose switch + +Example: + +codec: wm8280@0 { + compatible = "wlf,wm8280"; + reg = <0>; + ... + + wlf,use-jd2; + wlf,use-jd2-nopull; + wlf,jd-invert; + + wlf,micd-software-compare; + wlf,micd-detect-debounce = <0>; + wlf,micd-pol-gpio = <&codec 2 0>; + wlf,micd-rate = <ARIZONA_MICD_TIME_8MS>; + wlf,micd-dbtime = <4>; + wlf,micd-timeout-ms = <100>; + wlf,micd-force-micbias; + wlf,micd-configs = < + 0 1 0 /* MICDET1 MICBIAS1 GPIO=low */ + 1 2 1 /* MICDET2 MICBIAS2 GPIO=high */ + >; + + wlf,gpsw = <0>; +}; diff --git a/Documentation/devicetree/bindings/extcon/extcon-max3355.txt b/Documentation/devicetree/bindings/extcon/extcon-max3355.txt new file mode 100644 index 000000000000..f2288ea9eb82 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-max3355.txt @@ -0,0 +1,21 @@ +Maxim Integrated MAX3355 USB OTG chip +------------------------------------- + +MAX3355 integrates a charge pump and comparators to enable a system with an +integrated USB OTG dual-role transceiver to function as a USB OTG dual-role +device. + +Required properties: +- compatible: should be "maxim,max3355"; +- maxim,shdn-gpios: should contain a phandle and GPIO specifier for the GPIO pin + connected to the MAX3355's SHDN# pin; +- id-gpios: should contain a phandle and GPIO specifier for the GPIO pin + connected to the MAX3355's ID_OUT pin. + +Example: + + usb-otg { + compatible = "maxim,max3355"; + maxim,shdn-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; + id-gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>; + }; |