diff options
Diffstat (limited to 'Documentation')
12 files changed, 308 insertions, 60 deletions
diff --git a/Documentation/IRQ-domain.txt b/Documentation/IRQ-domain.txt index 39cfa72732ff..3a8e15cba816 100644 --- a/Documentation/IRQ-domain.txt +++ b/Documentation/IRQ-domain.txt @@ -95,8 +95,7 @@ since it doesn't need to allocate a table as large as the largest hwirq number. The disadvantage is that hwirq to IRQ number lookup is dependent on how many entries are in the table. -Very few drivers should need this mapping. At the moment, powerpc -iseries is the only user. +Very few drivers should need this mapping. ==== No Map ===- irq_domain_add_nomap() diff --git a/Documentation/devicetree/bindings/clock/pistachio-clock.txt b/Documentation/devicetree/bindings/clock/pistachio-clock.txt new file mode 100644 index 000000000000..868db499eed2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/pistachio-clock.txt @@ -0,0 +1,123 @@ +Imagination Technologies Pistachio SoC clock controllers +======================================================== + +Pistachio has four clock controllers (core clock, peripheral clock, peripheral +general control, and top general control) which are instantiated individually +from the device-tree. + +External clocks: +---------------- + +There are three external inputs to the clock controllers which should be +defined with the following clock-output-names: +- "xtal": External 52Mhz oscillator (required) +- "audio_clk_in": Alternate audio reference clock (optional) +- "enet_clk_in": Alternate ethernet PHY clock (optional) + +Core clock controller: +---------------------- + +The core clock controller generates clocks for the CPU, RPU (WiFi + BT +co-processor), audio, and several peripherals. + +Required properties: +- compatible: Must be "img,pistachio-clk". +- reg: Must contain the base address and length of the core clock controller. +- #clock-cells: Must be 1. The single cell is the clock identifier. + See dt-bindings/clock/pistachio-clk.h for the list of valid identifiers. +- clocks: Must contain an entry for each clock in clock-names. +- clock-names: Must include "xtal" (see "External clocks") and + "audio_clk_in_gate", "enet_clk_in_gate" which are generated by the + top-level general control. + +Example: + clk_core: clock-controller@18144000 { + compatible = "img,pistachio-clk"; + reg = <0x18144000 0x800>; + clocks = <&xtal>, <&cr_top EXT_CLK_AUDIO_IN>, + <&cr_top EXT_CLK_ENET_IN>; + clock-names = "xtal", "audio_clk_in_gate", "enet_clk_in_gate"; + + #clock-cells = <1>; + }; + +Peripheral clock controller: +---------------------------- + +The peripheral clock controller generates clocks for the DDR, ROM, and other +peripherals. The peripheral system clock ("periph_sys") generated by the core +clock controller is the input clock to the peripheral clock controller. + +Required properties: +- compatible: Must be "img,pistachio-periph-clk". +- reg: Must contain the base address and length of the peripheral clock + controller. +- #clock-cells: Must be 1. The single cell is the clock identifier. + See dt-bindings/clock/pistachio-clk.h for the list of valid identifiers. +- clocks: Must contain an entry for each clock in clock-names. +- clock-names: Must include "periph_sys", the peripheral system clock generated + by the core clock controller. + +Example: + clk_periph: clock-controller@18144800 { + compatible = "img,pistachio-clk-periph"; + reg = <0x18144800 0x800>; + clocks = <&clk_core CLK_PERIPH_SYS>; + clock-names = "periph_sys"; + + #clock-cells = <1>; + }; + +Peripheral general control: +--------------------------- + +The peripheral general control block generates system interface clocks and +resets for various peripherals. It also contains miscellaneous peripheral +control registers. The system clock ("sys") generated by the peripheral clock +controller is the input clock to the system clock controller. + +Required properties: +- compatible: Must include "img,pistachio-periph-cr" and "syscon". +- reg: Must contain the base address and length of the peripheral general + control registers. +- #clock-cells: Must be 1. The single cell is the clock identifier. + See dt-bindings/clock/pistachio-clk.h for the list of valid identifiers. +- clocks: Must contain an entry for each clock in clock-names. +- clock-names: Must include "sys", the system clock generated by the peripheral + clock controller. + +Example: + cr_periph: syscon@18144800 { + compatible = "img,pistachio-cr-periph", "syscon"; + reg = <0x18148000 0x1000>; + clocks = <&clock_periph PERIPH_CLK_PERIPH_SYS>; + clock-names = "sys"; + + #clock-cells = <1>; + }; + +Top-level general control: +-------------------------- + +The top-level general control block contains miscellaneous control registers and +gates for the external clocks "audio_clk_in" and "enet_clk_in". + +Required properties: +- compatible: Must include "img,pistachio-cr-top" and "syscon". +- reg: Must contain the base address and length of the top-level + control registers. +- clocks: Must contain an entry for each clock in clock-names. +- clock-names: Two optional clocks, "audio_clk_in" and "enet_clk_in" (see + "External clocks"). +- #clock-cells: Must be 1. The single cell is the clock identifier. + See dt-bindings/clock/pistachio-clk.h for the list of valid identifiers. + +Example: + cr_top: syscon@18144800 { + compatible = "img,pistachio-cr-top", "syscon"; + reg = <0x18149000 0x200>; + clocks = <&audio_refclk>, <&ext_enet_in>; + clock-names = "audio_clk_in", "enet_clk_in"; + + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm3380-l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm3380-l2-intc.txt new file mode 100644 index 000000000000..8f48aad50868 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm3380-l2-intc.txt @@ -0,0 +1,41 @@ +Broadcom BCM3380-style Level 1 / Level 2 interrupt controller + +This interrupt controller shows up in various forms on many BCM338x/BCM63xx +chipsets. It has the following properties: + +- outputs a single interrupt signal to its interrupt controller parent + +- contains one or more enable/status word pairs, which often appear at + different offsets in different blocks + +- no atomic set/clear operations + +Required properties: + +- compatible: should be "brcm,bcm3380-l2-intc" +- reg: specifies one or more enable/status pairs, in the following format: + <enable_reg 0x4 status_reg 0x4>... +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- interrupt-parent: specifies the phandle to the parent interrupt controller + this one is cascaded from +- interrupts: specifies the interrupt line in the interrupt-parent controller + node, valid values depend on the type of parent interrupt controller + +Optional properties: + +- brcm,irq-can-wake: if present, this means the L2 controller can be used as a + wakeup source for system suspend/resume. + +Example: + +irq0_intc: interrupt-controller@10000020 { + compatible = "brcm,bcm3380-l2-intc"; + reg = <0x10000024 0x4 0x1000002c 0x4>, + <0x10000020 0x4 0x10000028 0x4>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&cpu_intc>; + interrupts = <2>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7038-l1-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7038-l1-intc.txt new file mode 100644 index 000000000000..cc217b22dccd --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7038-l1-intc.txt @@ -0,0 +1,52 @@ +Broadcom BCM7038-style Level 1 interrupt controller + +This block is a first level interrupt controller that is typically connected +directly to one of the HW INT lines on each CPU. Every BCM7xxx set-top chip +since BCM7038 has contained this hardware. + +Key elements of the hardware design include: + +- 64, 96, 128, or 160 incoming level IRQ lines + +- Most onchip peripherals are wired directly to an L1 input + +- A separate instance of the register set for each CPU, allowing individual + peripheral IRQs to be routed to any CPU + +- Atomic mask/unmask operations + +- No polarity/level/edge settings + +- No FIFO or priority encoder logic; software is expected to read all + 2-5 status words to determine which IRQs are pending + +Required properties: + +- compatible: should be "brcm,bcm7038-l1-intc" +- reg: specifies the base physical address and size of the registers; + the number of supported IRQs is inferred from the size argument +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- interrupt-parent: specifies the phandle to the parent interrupt controller(s) + this one is cascaded from +- interrupts: specifies the interrupt line(s) in the interrupt-parent controller + node; valid values depend on the type of parent interrupt controller + +If multiple reg ranges and interrupt-parent entries are present on an SMP +system, the driver will allow IRQ SMP affinity to be set up through the +/proc/irq/ interface. In the simplest possible configuration, only one +reg range and one interrupt-parent is needed. + +Example: + +periph_intc: periph_intc@1041a400 { + compatible = "brcm,bcm7038-l1-intc"; + reg = <0x1041a400 0x30 0x1041a600 0x30>; + + interrupt-controller; + #interrupt-cells = <1>; + + interrupt-parent = <&cpu_intc>; + interrupts = <2>, <3>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt index bae1f2187226..44a9bb15dd56 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt @@ -13,8 +13,7 @@ Such an interrupt controller has the following hardware design: or if they will output an interrupt signal at this 2nd level interrupt controller, in particular for UARTs -- typically has one 32-bit enable word and one 32-bit status word, but on - some hardware may have more than one enable/status pair +- has one 32-bit enable word and one 32-bit status word - no atomic set/clear operations @@ -53,9 +52,7 @@ The typical hardware layout for this controller is represented below: Required properties: - compatible: should be "brcm,bcm7120-l2-intc" -- reg: specifies the base physical address and size of the registers; - multiple pairs may be specified, with the first pair handling IRQ offsets - 0..31 and the second pair handling 32..63 +- reg: specifies the base physical address and size of the registers - interrupt-controller: identifies the node as an interrupt controller - #interrupt-cells: specifies the number of cells needed to encode an interrupt source, should be 1. @@ -66,10 +63,7 @@ Required properties: - brcm,int-map-mask: 32-bits bit mask describing how many and which interrupts are wired to this 2nd level interrupt controller, and how they match their respective interrupt parents. Should match exactly the number of interrupts - specified in the 'interrupts' property, multiplied by the number of - enable/status register pairs implemented by this controller. For - multiple parent IRQs with multiple enable/status words, this looks like: - <irq0_w0 irq0_w1 irq1_w0 irq1_w1 ...> + specified in the 'interrupts' property. Optional properties: diff --git a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt index 5a65478e5d40..aae4c384ee1f 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt @@ -27,8 +27,13 @@ Optional properties: Required properties for timer sub-node: - compatible : Should be "mti,gic-timer". - interrupts : Interrupt for the GIC local timer. + +Optional properties for timer sub-node: +- clocks : GIC timer operating clock. - clock-frequency : Clock frequency at which the GIC timers operate. +Note that one of clocks or clock-frequency must be specified. + Example: gic: interrupt-controller@1bdc0000 { diff --git a/Documentation/devicetree/bindings/mips/brcm/bcm3384-intc.txt b/Documentation/devicetree/bindings/mips/brcm/bcm3384-intc.txt deleted file mode 100644 index d4e0141d3620..000000000000 --- a/Documentation/devicetree/bindings/mips/brcm/bcm3384-intc.txt +++ /dev/null @@ -1,37 +0,0 @@ -* Interrupt Controller - -Properties: -- compatible: "brcm,bcm3384-intc" - - Compatibility with BCM3384 and possibly other BCM33xx/BCM63xx SoCs. - -- reg: Address/length pairs for each mask/status register set. Length must - be 8. If multiple register sets are specified, the first set will - handle IRQ offsets 0..31, the second set 32..63, and so on. - -- interrupt-controller: This is an interrupt controller. - -- #interrupt-cells: Must be <1>. Just a simple IRQ offset; no level/edge - or polarity configuration is possible with this controller. - -- interrupt-parent: This controller is cascaded from a MIPS CPU HW IRQ, or - from another INTC. - -- interrupts: The IRQ on the parent controller. - -Example: - periph_intc: periph_intc@14e00038 { - compatible = "brcm,bcm3384-intc"; - - /* - * IRQs 0..31: mask reg 0x14e00038, status reg 0x14e0003c - * IRQs 32..63: mask reg 0x14e00340, status reg 0x14e00344 - */ - reg = <0x14e00038 0x8 0x14e00340 0x8>; - - interrupt-controller; - #interrupt-cells = <1>; - - interrupt-parent = <&cpu_intc>; - interrupts = <4>; - }; diff --git a/Documentation/devicetree/bindings/mips/brcm/cm-dsl.txt b/Documentation/devicetree/bindings/mips/brcm/cm-dsl.txt deleted file mode 100644 index 8a139cb3c0b5..000000000000 --- a/Documentation/devicetree/bindings/mips/brcm/cm-dsl.txt +++ /dev/null @@ -1,11 +0,0 @@ -* Broadcom cable/DSL platforms - -SoCs: - -Required properties: -- compatible: "brcm,bcm3384", "brcm,bcm33843" - -Boards: - -Required properties: -- compatible: "brcm,bcm93384wvg" diff --git a/Documentation/devicetree/bindings/mips/brcm/soc.txt b/Documentation/devicetree/bindings/mips/brcm/soc.txt new file mode 100644 index 000000000000..7bab90cc4a7b --- /dev/null +++ b/Documentation/devicetree/bindings/mips/brcm/soc.txt @@ -0,0 +1,12 @@ +* Broadcom cable/DSL/settop platforms + +Required properties: + +- compatible: "brcm,bcm3384", "brcm,bcm33843" + "brcm,bcm3384-viper", "brcm,bcm33843-viper" + "brcm,bcm6328", "brcm,bcm6368", + "brcm,bcm7125", "brcm,bcm7346", "brcm,bcm7358", "brcm,bcm7360", + "brcm,bcm7362", "brcm,bcm7420", "brcm,bcm7425" + +The experimental -viper variants are for running Linux on the 3384's +BMIPS4355 cable modem CPU instead of the BMIPS5000 application processor. diff --git a/Documentation/devicetree/bindings/mips/img/pistachio.txt b/Documentation/devicetree/bindings/mips/img/pistachio.txt new file mode 100644 index 000000000000..a736d889c2b8 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/img/pistachio.txt @@ -0,0 +1,42 @@ +Imagination Pistachio SoC +========================= + +Required properties: +-------------------- + - compatible: Must include "img,pistachio". + +CPU nodes: +---------- +A "cpus" node is required. Required properties: + - #address-cells: Must be 1. + - #size-cells: Must be 0. +A CPU sub-node is also required for at least CPU 0. Since the topology may +be probed via CPS, it is not necessary to specify secondary CPUs. Required +propertis: + - device_type: Must be "cpu". + - compatible: Must be "mti,interaptiv". + - reg: CPU number. + - clocks: Must include the CPU clock. See ../../clock/clock-bindings.txt for + details on clock bindings. +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "mti,interaptiv"; + reg = <0>; + clocks = <&clk_core CLK_MIPS>; + }; + }; + + +Boot protocol: +-------------- +In accordance with the MIPS UHI specification[1], the bootloader must pass the +following arguments to the kernel: + - $a0: -2. + - $a1: KSEG0 address of the flattened device-tree blob. + +[1] http://prplfoundation.org/wiki/MIPS_documentation diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index 77685185cf3b..e49e423268c0 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -15,6 +15,7 @@ Table of Contents 1) Entry point for arch/arm 2) Entry point for arch/powerpc 3) Entry point for arch/x86 + 4) Entry point for arch/mips/bmips II - The DT block format 1) Header @@ -288,6 +289,33 @@ it with special cases. or initrd address. It simply holds information which can not be retrieved otherwise like interrupt routing or a list of devices behind an I2C bus. +4) Entry point for arch/mips/bmips +---------------------------------- + + Some bootloaders only support a single entry point, at the start of the + kernel image. Other bootloaders will jump to the ELF start address. + Both schemes are supported; CONFIG_BOOT_RAW=y and CONFIG_NO_EXCEPT_FILL=y, + so the first instruction immediately jumps to kernel_entry(). + + Similar to the arch/arm case (b), a DT-aware bootloader is expected to + set up the following registers: + + a0 : 0 + + a1 : 0xffffffff + + a2 : Physical pointer to the device tree block (defined in chapter + II) in RAM. The device tree can be located anywhere in the first + 512MB of the physical address space (0x00000000 - 0x1fffffff), + aligned on a 64 bit boundary. + + Legacy bootloaders do not use this convention, and they do not pass in a + DT block. In this case, Linux will look for a builtin DTB, selected via + CONFIG_DT_*. + + This convention is defined for 32-bit systems only, as there are not + currently any 64-bit BMIPS implementations. + II - The DT block format ======================== diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 491bbd104b06..11a76df2e1f1 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -2317,7 +2317,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted. noexec32=off: disable non-executable mappings read implies executable mappings - nofpu [SH] Disable hardware FPU at boot time. + nofpu [MIPS,SH] Disable hardware FPU at boot time. nofxsr [BUGS=X86-32] Disables x86 floating point extended register save and restore. The kernel will only save |